Upload
belinda-copeland
View
217
Download
1
Tags:
Embed Size (px)
Citation preview
MOTOR
Made by:Tomas Leiva, Marco and
Mathieu Maldemay
History
Since the early 18th century, steam power has been applied to a variety of practical uses.In 1698 Thomas Savery patented a steam pump that used steam in direct contact with the water being pumped. Savery's steam pump used condensing steam to create a vacuum and draw water into a chamber, and then applied pressurized steam to further pump the water. Thomas Newcomen's atmospheric engine was the first commercial true steam engine using a piston, and was used in 1712 for pumping in a mine. In 1781 James Watt patented a steam engine that produced continuous rotary motion. Watt's ten-horsepower engines enabled a wide range of manufacturing machinery to be powered.
Steam engine
A steam engine is a heat engine that performs mechanical work using steam as its working fluid. Using boiling water to produce mechanical motion goes back over 2000 years, but early devices were not practical.
Electric motor
• An electric motor is an electrical machine that converts electrical energy into mechanical energy. The reverse of this would be the conversion of mechanical energy into electrical energy and is done by an electric generator. Electric motors can operate in both motoring and generating or braking modes to also produce electrical energy from mechanical energy. Electric motors can be powered by direct current (DC) sources, such as from batteries, motor vehicles or rectifiers, or by alternating current (AC) sources, such as from the power grid, inverters or generators.
Diesel engine
• The diesel engine is an internal combustion engine in which ignition of the fuel that has been injected into the combustion chamber is initiated by the high temperature which a gas achieves when greatly compressed. This contrasts with spark-ignition engines such as a petrol engine or gas engine, which use a spark plug to ignite an air-fuel mixture.
Cylinder • A cylinder is the central working part of a
reciprocating engine or pump, the space in which a piston travels. Multiple cylinders are commonly arranged side by side in a bank, or engine block, which is typically cast from aluminum or cast iron before receiving precision machine work. Cylinders may be sleeved or sleeveless .
Cylinder head
• the cylinder head sits above the cylinders on top of the cylinder block. It closes in the top of the cylinder, forming the combustion chamber. This joint is sealed by a head gasket. In most engines, the head also provides space for the passages that feed air and fuel to the cylinder, and that allow the exhaust to escape. The head can also be a place to mount the valves, spark plugs, and fuel injectors.
Piston
• A piston is a component of reciprocating engines, reciprocating pumps, gas compressors and pneumatic cylinders, among other similar mechanisms. In an engine, its purpose is to transfer force from expanding gas in the cylinder to the crankshaft via a piston rod and/or connecting rod. In a pump, the function is reversed and force is transferred from the crankshaft to the piston for the purpose of compressing or ejecting the fluid in the cylinder. In some engines, the piston also acts as a valve by covering and uncovering ports in the cylinder wall.
camshaft• A camshaft is a shaft to which a cam
is fastened or of which a cam forms an integral part. the camshaft is used to operate poppet valves. It then consists of a cylindrical rod running the length of the cylinder bank with a number of oblong lobes protruding from it, one for each valve.
exhaust system
An exhaust system is usually piping used to guide reaction exhaust gases away from a controlled combustion inside an engine or stove. The entire system conveys burnt gases from the engine and includes one or more exhaust pipes. Depending on the overall system design, the exhaust gas may flow through one or more of:• Cylinder head and exhaust manifold• A turbocharger to increase engine power.• A catalytic converter to reduce air
pollution.• A muffler to reduce noise.
INTAKE
• An intake, or especially for aircraft inlet, is an air intake for an engine. Because the modern internal combustion engine is in essence a powerful air pump, like the exhaust system on an engine, the intake must be carefully engineered and tuned to provide the greatest efficiency and power. An ideal intake system should increase the velocity of the air until it travels into the combustion chamber, while minimizing turbulence and restriction of flow.
Exhaust valve
• A poppet valve is a valve typically used to control the timing and quantity of gas or vapor flow into an engine. It consists of a hole, usually round or oval, and a tapered plug, usually a disk shape on the end of a shaft also called a valve stem. The portion of the hole where the plug meets with it is referred as the 'seat' or 'valve seat'. The shaft guides the plug portion by sliding through a valve guide.
filter
There is three type of filter in a motor.• Oil filter: An oil filter is a filter designed to remove
contaminants from engine oil, transmission oil, lubricating oil, or hydraulic oil.
• Fuel filter: A fuel filter is a filter in the fuel linethat screens out dirt and rust particles from the fuel, normally made into cartridges containing a filter paper. They are found in most internal combustion engines.• Air filter: A particulate air filter is a device composed of fibrous materials which removes solid particulates such as dust, pollen, mould, and bacteria from the air.
Oil filter
TURBOS• A turbocharger, or turbo it is a turbine-
driven forced induction device that increases an engine's efficiency and power by forcing extra air into the combustion chamber. This improvement over a naturally aspirated engine's output results because the turbine can force more air, and proportionately more fuel, into the combustion chamber than atmospheric pressure alon
supercharger• A supercharger is an air compressor
that increases the pressure or density of air supplied to an internal combustion engine. This gives each intake cycle of the engine more oxygen, letting it burn more fuel and do more work, thus increasing power.
Spark plug • A spark plug is a device for delivering electric current
from an ignition system to the combustion chamber of a spark-ignition engine to ignite the compressed fuel/air mixture by an electric spark, while containing combustion pressure within the engine. A spark plug has a metal threaded shell, electrically isolated from a central electrode by a porcelain insulator. The central electrode, which may contain a resistor, is connected by a heavily insulated wire to the output terminal of an ignition coil or magneto.
Transmission • A machine consists of a power source and a
power transmission system, which provides controlled application of the power. Merriam-Webster defines transmission as an assembly of parts including the speed-changing gears and the propeller shaft by which the power is transmitted from an engine to a live axle. Often transmission refers simply to the gearbox that uses gears and gear trains to provide speed and torque conversions from a rotating power source to another device.
Crankshaft • A crankshaft is a mechanical part able to perform
a conversion between reciprocating motion and rotational motion. In a reciprocating engine, it translates reciprocating motion of the piston into rotational motion whereas in a reciprocating compressor, it converts the rotational motion into reciprocating motion. In order to do the conversion between two motions, the crankshaft has crank throws or crankpin, additional bearing surfaces whose axis is offset from that of the crank, to which the big ends of the connecting rods from each cylinder attach.
Starter
• A starter is an electric motor, pneumatic motor, hydraulic motor, an internal-combustion engine in case of very large engines or other device used for rotating an internal-combustion engine so as to initiate the engine's operation under its own power.
Power steering
• In automobiles, power steering helps drivers steer by augmenting steering effort of the steering wheel. Hydraulic or electric actuators add controlled energy to the steering mechanism, so the driver needs to provide only modest effort regardless of conditions. Power steering helps considerably when a vehicle is stopped or moving slowly. Also, power steering provides some feedback of forces acting on the front wheels to give an ongoing sense of how the wheels are interacting with the road; this is typically called "road feel".