Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
Single Handle Lavatory Faucet With Pop-up
3 Hole or Single Hole Installation
Model No. : 192-5889 Polished Chrome 192-5890 Brushed Nickel 192-5891 Oil-Rubbed Bronze
Rev 01/29/15
1
2
3
4
5
6
7
910
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 Allen Key
Aerator Wrench
Index
Screw
Aerator
Bolt
Locknut
Clamp
Putty Plate
Deck Plate
O-ring
Body
Cartridge
Cartridge Locknut
Trim Cap
Handle
Copper tube
Part NameNo.
5
Screwdriver
20
21
22
232425
26
27
29 30
28
31
32
11
12
13
14
15
16
17
8
18
19Flange
Locknut
Drain Body
Lift Rod
Extend Rod
Horizontal Rod
Rod Guide Nut
Top Rubber Washer
Bottom Rubber Washer
Drain Stopper
Washer
Tailpiece
Rod Ball Plastic Gasket
Fittings
20
21
22
23
24
25
26
27
28
29
30
31
32
Copper tube
Plumber's Putty
14
A. B. C.
Install With Deck Plate
Install Without Deck Plate
12
13
14
16
17
1.Position the faucet, deck plate 13 and putty plate 14 in order on the
countertop as shown. Don't forget the o-ring 12 .
2.Fix the faucet with clamp 16 and locknut 17 , and tighten the locknut with
basin wrench. But DON'T OVER TIGHTEN.
Add silicone under faucet to prevent leaks.(Optional)
1.Position the faucet in order on the countertop as shown. Don't forget the
o-ring 12 .
2.Fix the faucet with clamp 16 and locknut 17 ,and tighten the locknut with
basin wrench.But DON'T OVER TIGHTEN.
1216
17
Warning:
The supply valves and
supply lines are not
included, please
purchase them at a
plumbing supply store.
t
32
rod guide nut 30rod ballplasticgasket 29
drainstopperhole
drainbody 26
o-ring
sink
drain stopper 20
flange 21
align hole in drain stopperwith guide rodopening(pointed towardback wall)
flange 21
drain body 26
top rubber washer 22
sink base
locknut 25
washer 24 bottomrubberwasher 23
tailpiece 27
A. Insert lift rod 11 through hole
on faucet body.
B.Connect extend rod 32 to lift
rod 11 .Attach horizontal rod 28
to extend rod 32 using fittings 31,
tighten screw.
lift rod 11
faucetbody
extend rod 32
horizontal rod 28
screw
fittings 31
A. Replace pop-up drain stopper 20
to drain body 26 with o-ring
in place, and align stopper hole
with guide rod opening.
A. Remove rod guide nut 30 and
rod ball plastic gasket 29 .
B. Insert horizontal rod 28 into
drain body 26 and through hole
in drain stopper 20.
C. Replace rod guide nut 30 with
rod ball plastic gasket 29 and
tighten it.
horizontal rod 28
drainbody 26
A. Remove pop-up drain stopper 20.
and flange 21 with top rubber
washer 22 for pop-up assembly.
B. Insert drain body from underneath
of sink drain hole.Replace flange 21
and top rubber washer 22 back to
drain body 26.Tighten flange as far
as possible. Remove 22 and put
silicone along bottom of 21 .(Optional)
C. Slide bottom rubber washer 23
on drain body up against bottom
of sink. Tighten washer 24 and
locknut 25 firmly against base
for tight seal.
D.Remove tailpiece 27 from drain
body 26 ,add Teflon tape,replace
tailpiece 27.