MODEL NI8 AL-XX70-B RS-X70 20210302 AVAILABLE …

MODELOL-HRN-RS-NI8

GUIDE IDNI8_AL-XX70-B_RS-X70_20220131

AVAILABLE ACCESSORIESOL-HRN-RS-PWR (Adapt to any brand remote start)

INSTALL GUIDE

VEHICLE COMPATIBILITY

DISCLAIMER: The manufacturer of this product nor its affiliates accept any responsibility for any electrical damage to the vehicle or any other connected systems as a result of improper installation of this product. All wiring connections & vehicle compatibility must be verified by a professionally qualified technician prior to installation.!

For AL-XX70-B installations see pages 2-13For RS-X70 installations see pages 14-25

For OL-MDB-ALL Stand-Alone installations see pages 26-36

Infiniti QX50 Push-to-Start Automatic 2019 - 2020 DL-NI8 RS-NI8 4

Nissan Altima Push-to-Start Sedan Automatic 2019 - 2021 DL-NI8 RS-NI8 2

Nissan Qashqai Push-to-Start 4 Cyl. Automatic 2017 - 2020 DL-NI8 RS-NI8 2

Nissan Qashqai Std. Key 4 Cyl. Automatic 2017 - 2018 DL-NI9 RS-NI9 2

Nissan Qashqai Std. Key 4 Cyl. Automatic 2019- 2020 DL-NI9 RS-NI9 3

Nissan Rogue Push-to-Start 4 Cyl. Automatic 2014 - 2016 DL-NI8 RS-NI8 1

Nissan Rogue Push-to-Start 4 Cyl. Automatic 2017 - 2020 DL-NI8 RS-NI8 2

Nissan Rogue Std. Key 4 Cyl. Automatic 2014 - 2016 DL-NI9 RS-NI9 1



Nissan Rogue Sport Push-to-Start 4 Cyl. Automatic 2017 - 2020 DL-NI8 RS-NI8 2

Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2017 - 2018 DL-NI9 RS-NI9 2

Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2019 - 2020 DL-NI9 RS-NI9 3

Make Model Trim YearsFirmware

DiagramXX70 or X70 Stand-Alone

For AL-XX70-B & RS-X70 installations configure Installer Feature #9 to LOCK AFTER RS OFF to control

RAP/Autolight Shutdown. See system installtion guide for programming instructions

INSTALL GUIDEGUIDE ID: NI8_AL-XX70-B_RS-X70_20220131 Page 2 of 36

MODEL: OL-HRN-RS-NI8

INSTALLATION STEPS:1) Go to OmegaWeblink.com or use WebLink Mobile to fl ash the OL-BLADE-AL64 with the fi rmware matching the vehicle.

NOTE: If OEM remote is being used to activate the remote start be sure to enable “Factory keyless RS sequence” as “Lock + Lock + Lock” OR “Lock + Unlock + Lock”2) While at OmegaWeblink.com, make sure the AL-XX70-B is updated to v1.5 FW or higher.3) Make all the connections shown in the diagram on the following pages.4) Connect any optional hardware as needed.5) Program the OL-BLADE-AL64 to the vehicle (see “BLADE Programming” on the following pages).6) Perform Vehicle Learn to confi gure the remote start to match the vehicle (see “AL-XX70-B Programming/Vehicle Learn” on the following pages).

NOTE: If Vehicle Learn is not performed remote start operation could fail.7) Test the system for all desired functions.

NOTE: Any features NOT supported by the interface module must be hard wired from the remote start to the vehicle. Refer to the remote start install guide and vehicle wiring info at www.wiresheet.com (only available for authorized dealers) for instructions.

AL-XX70-B Layout

F WHITE 4 PIN PLUG-IN SENSOR PORTS (harness included w/ optional sensors)

G TEMPERATURE SENSOR - DO NOT COVER(For high/low temp auto start and for automatic low temp crank extender)

H BLADE CARTRIDGE PORT - For OL-BLADE-AL64 or OL-BLADE-TB

I GREEN & BLACK DATA PORTS - For Telematics / Data Sensor (Shock, Tilt, etc) / Vehicle Interface Module. (DBI & iDatalink protocols supported on both ports - see ‘Vehicle Learn’ or installer feature #12)

J BLADE HARNESS PORT - Use harness from BLADE or an ‘OL-HRN-RS’ T-Harness.

L BACKUP BATTERY PORT - Uses standard 9v battery with bracket & plug. Featuring PowerMaze technology - only supports security critical functions!

K ANTENNA / STATUS LIGHT / VALET PORT - Supports compatible plug-in antennas or push-button status light (P/N: AU-LED-PB2)

A WHITE 6 PIN HIGH CURRENT POWER HARNESS (P/N: H-RS6E*)

B WHITE 18 PIN MAIN INPUT/OUTPUT HARNESS (P/N: H-RS18A)

C RED 4 PIN DOOR LOCK/UNLOCK HARNESS (P/N: DLP-N4)

D RED 3 PIN REMOTE START HARNESS (P/N: RS-OUTPUT)

E WHITE 4 PIN AUXILIARY HARNESS (P/N: H-RS4)

F

C D E I J K

G

L

H

AB

AL-XX70-B Installation Steps


MODEL: OL-HRN-RS-NI8Wire Location Chart Diagram #1

Nissan Rogue Push-to-Start 4 Cyl. Automatic 2014 - 2016

Body Control Module - - - - - Under Driver Side Dash

Horn WHITE 100 35 TAN (-) Driver Kick Panel

Lift Gate GREEN 8 6 LT.GREEN (-) At Switch On Lower Dash

Nissan Rogue Std. Key 4 Cyl. Automatic 2014 - 2016




Make Model Trim Year Item Connector Color

Connector Pins Pin # Wire Color Polarity Location



J

E

PIN COLOR1 PINK2 WHITE/BLUE3 LT. GREEN/RED4 LT. GREEN/BLACK

1

4

N/CN/CN/CN/C

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

BLUE

N/CN/CN/C

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

RED

N/CN/CN/C

C

B

PIN COLOR1 VIOLET/WHITE2 BLACK/RED3 GREEN/VIOLET4 WHITE/BLACK5 BROWN/RED6 WHITE/RED7 WHITE8 BROWN/BLACK9 VIOLET/BLACK

10 GREEN11 VIOLET12 RED/WHITE13 ORANGE14 BLACK15 BLACK/WHITE16 GRAY17 BROWN18 BLUE/BLACK

110

918

N/CN/CN/C

N/CN/CN/CN/C

N/CN/C

N/C

N/C

N/C

A

AL-XX70-B Diagram #1

Door Lock Option A

Door Lock Option B

CAN Option A

CAN Option B

BLUE/BLACK - OEM Horn (-) OutputOPTIONAL

BROWN - Siren (+) OutputOPTIONAL

BLACK -Chassis Ground

Optional Siren

RED

OEM Horn

GRAY - Connect to supplied hood pin IF no OEM hood pin is present

A

PINK - Not Used

CB

BCM HARNESS (BLACK CONN)

DE

BCM HARNESS (GRAY CONN)

HJ


OL-HRN-RS-NI8(A)

OL-HRN-RS-NI8(D)DL-NI8/9

DO NOT CONNECT

BLACK - Ground

FG

Body Control Module

DO NOT CONNECT

DO NOT CONNECT

K L

VEHICLE’S OBDII

CONNECTOR

RED/WHITE - Trunk Release (-) OutputPower Liftgate

OPTIONAL



Nissan Altima Push-to-Start Sedan Automatic 2019 - 2021


Horn BLACK 16 10 VIOLET (-) Horn Switch On Column

Trunk Release GRAY 4 2 BROWN (-) At Liftgate Switch Lower Dash Panel

Nissan Qashqai Push-to-Start 4 Cyl. Automatic 2017 - 2020


Horn WHITE 14 14 WHITE (-) At Horn Switch On Column

Lift Gate GREEN 8 6 LT.GREEN (-) At Liftgate Switch Lower Dash Panel

Nissan Qashqai Std. Key 4 Cyl. Automatic 2017 - 2018












Nissan Rogue Sport Push-to-Start 4 Cyl. Automatic 2017 - 2020


Horn WHITE 100 79 PINK (-) Driver Kick Panel


Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2017 - 2018



Lift Gate GREEN 8 6 LT. GREEN (-) At Liftgate Switch Lower Dash Panel





J

E


1

4

N/CN/CN/CN/C

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

BLUE

N/CN/CN/C

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

RED

N/CN/CN/C

C

B



110

918

N/CN/CN/C

N/CN/CN/CN/C

N/CN/C

N/C

N/C

N/C

A

AL-XX70-B Diagram #2

Door Lock Option A

Door Lock Option B

CAN Option B

CAN Option A



Optional Siren

RED


A

PINK - Not Used

CB




BLACK - Ground

BCM HARNESS (GREEN CONN)

Body Control Module

VEHICLE’S OBDII

CONNECTOR

OL-HRN-RS-NI8(A)



OEM Horn

RED/WHITE - Trunk Release (-) Output

Power Liftgate/Trunk Release

OPTIONAL

DO NOT CONNECT

DE

HJ

FGK L


















MODEL: OL-HRN-RS-NI8AL-XX70-B Diagram #3

J

E


1

4

N/CN/CN/CN/C

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

BLUE

N/CN/CN/C

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

RED

N/CN/CN/C

C

B



110

918

N/CN/CN/C

N/CN/CN/CN/C

N/CN/C

N/C

N/C

N/C

A

Door Lock Option A

Door Lock OptionB

CAN Option B

CAN Option A

CONNECT



Optional Siren

RED


A

PINK - Not Used

CB




BLACK - Ground


Body Control Module

VEHICLE’S OBDII

CONNECTOR

OL-HRN-RS-NI8(A)



OEM Horn


OPTIONAL

DE

HJ

FGK L



Infiniti QX50 Push-to-Start Automatic 2019 - 2020


Horn WHITE 100 18 GRAY (-) Driver Kick Panel

Lift Gate WHITE 16 4 WHITE (-) At Liftgate Switch Lower Dash Panel




MODEL: OL-HRN-RS-NI8AL-XX70-B Diagram #4

J

E


1

4

N/CN/CN/CN/C

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

BLUE

N/CN/CN/C

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

RED

N/CN/CN/C

C

B



110

918

N/CN/CN/C

N/CN/CN/CN/C

N/CN/C

N/C

N/C

N/C

A

Door Lock Option B

Door Lock Option A

CAN Option B

CAN Option A



Optional Siren

RED


A

PINK - Not Used

CB




BLACK - Ground


Body Control Module

VEHICLE’S OBDII

CONNECTOR

OL-HRN-RS-NI8(A)



OEM Horn

RED/WHITE - Trunk Release (-) OutputTrunk Release

OPTIONAL

CONNECT

DE

HJ

FGK L



YELLOW - Alarm notifi cation input (+/-)

AL-XX70-B Optional Accessories

Antenna Cable

Push-Button LED Cable

K Antenna/LED Cable OR

Mod

el: L

INKR

-LT

ww

w.o

meg

alin

kr.c

om

I

I OL-ADAPTOR-B2G DATA CABLE

DATA CABLE

OR

F SENSOR CABLE

BLACK

GREEN

Any Add-onSensor

AL-XX70-B MUST have V1.4 or newer fi rmware for Linkr-LT compatibility.


MODEL: OL-HRN-RS-NI8Blade Installation

Slide Blade into unit. Notice programming button under LED.

Blade Programming

Blade Programming (cont.)

OR

Wait, the LED will turn OFF.

Turn the ignition to the ON position.1

Turn the ignition to the OFF position.

4

Wait, the LED will turn solid RED, then solid BLUE for 1 second, then solid RED.

2

3

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

5

6

Turn the ignition to the ON position.

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

If LED flashes BLUE rapidly proceed with step 7. If LED turns solid BLUE for 2 seconds proceed to step 13.

WARNING:Disconnect power lastDisconnect remote start from vehicle.

WARNING: Do not press Blade programming button. Connect power first.Connect all other remote start connectors

10

Connect remote start to computer and proceed with extended programming.9

8

Turn the ignition to the OFF position.7

Proceed to AL-XX70-B Programming/Vehicle Learn.



14

Wait, the LED will turn solid RED, then solid BLUE for 1 second, then solid RED.

12

13

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON



AL-XX70-B Programming/Vehicle Learn V1.6 (see installation guide for older versions)

Before You Begin:- Make sure all wires/harnesses are connected.- Program the BLADE to the vehicle per the instructions on the previous pages.- Connect any additional accessories/modules to the data ports.- MANUAL TRANSMISSION VEHICLES ONLY: Set the parking brake. The BLACK/WHITE wire must be connected to the parking brake wire.

Within 5 seconds of step 1 press the Valet button 3x or send remote start command (by remote, Linkr, activa-tion input wire etc.).

- The system will chirp & fl ash lights to indicate crankdelay (Default: 1 chirp/fl ash = 1.5 sec)

- Press valet button to change crank delay- Chirps: 1=1.5 sec, 2=15 sec, 3=20 sec, 4=30 sec

2

Programming complete.8

MANUAL TRANSMISSIONS: Release the parking brake.

AUTOMATIC TRANSMISSIONS: Turn the ignition key OFF.

- The system will chirp & fl ash the lights equal the #of IGN/ACC/START circuits detected (Max: 4).

MANUAL - Proceed to step 5.AUTOMATIC - Skip to step 6.

4

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON Turn ignition to ON position (do not start).1

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON Start the engine with the key and let the engine reach normal idle.

3

TO SAVE SETTINGS/FINISH VEHICLE LEARN: Press the BRAKE pedal (will shut down RS).

- This disables VEHICLE LEARN (to enable again, programinstaller feature #2 (bank 10) to “Enabled”.

TO CANCEL/START OVER: Press the valet button once.

7

5 MANUAL TRANSMISSIONS: Set the parking brake again to enter Manual Transmission Reservation Mode option selection. (installer feature #11)

- The system will chirp & fl ash the light to indicate currentsetting (default: 2 - Off)

- Set and Release the parking brake to scrool through settingoptions.

- Chirp confi rmation: 1 = ON - Shutdown w/ lock, 2 = OFF,3 = ON - Shutdown w/ door close, 4 = ON - Shutdown 10sec. after door close

- Before turning the key OFF, perform the MT reservationsequence (see operation guide) and exit the vehicle.

6

TroubleShooting

- See system installation guide for remote start diagnostics and troubleshooting.- See OmegaLink module/fi rmware guide at www.wiresheet.com for interface module diagnostics and troubleshooting.

OR

Activate remote start (within 60 sec. of Step 4 or 5). Wait until engine is running and LED fl ashes slowly (10-45 seconds after engine cranks & runs).Push-to-Start vehicles: Ensure the OEM fob is at least 20 ft. away to allow remote start.

- The system will detect data protocols, select the bestavailable engine running detection method, and, learn anyavaialble tach input (data or analog).

3x

2x

2x



C D

AB

GFERS-X70 Layout

E TEMPERATURE SENSOR - DO NOT COVER(For high/low temp auto start and for automatic low temp crank extender)

F ANTENNA / STATUS LIGHT / VALET PORT - Supports compatible plug-in antennas or push-button status light (P/N: AU-LED-PB2)

G GREEN & BLACK DATA PORTS - For Telematics / Data Sensor (Shock, Tilt, etc) / Vehicle Interface Module. (DBI & iDatalink protocols supported on both ports - see ‘Vehicle Learn’ or installer feature #12)

A WHITE 6 PIN HIGH CURRENT POWER HARNESS (P/N: H-RS6E*)

B WHITE 14 PIN MAIN INPUT/OUTPUT HARNESS (P/N: H-RS14A)

C RED 3 PIN DOOR LOCK/UNLOCK HARNESS (P/N: DLP-N3)

D RED 3 PIN REMOTE START HARNESS (P/N: RS-OUTPUT)

RS-X70 Installation Steps

INSTALLATION STEPS:1) Go to www.OmegaWeblink.com or use WebLink Mobile to fl ash the bypass module with the fi rmware matching the vehicle.

NOTE: iDatalink 2-way protocol is recommended for full functionality.NOTE: If OEM remote is being used to activate the remote start be sure “Factory keyless RS sequence” is set to “Lock + Lock + Lock” OR “Lock + Unlock + Lock”

2) Make all the connections shown in the diagram on the following pages.3) Connect any optional hardware as needed.4) Select Data Mode and program the bypass module to the vehicle (see module programming instructions).5) Perform Vehicle Learn to confi gure the remote start to match the vehicle.

NOTE: If Vehicle Learn is not performed remote start operation could fail.6) Test the system for all desired functions.

NOTE: Any features NOT supported by the interface module must be hard wired from the remote start to the vehicle. Refer to the remote start install guide and vehicle wiring info at www.wiresheet.com (only available for authorized dealers) for instructions.















DATA CABLE

RS-X70 Diagram #1

G

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

N/CN/CN/C

C

B

PIN COLOR1 ORANGE2 WHITE/BLACK3 RED/WHITE4 LT. GREEN/BLACK5 GRAY6 VIOLET/WHITE7 BLACK/WHITE8 WHITE/BLUE9 YELLOW

10 LT. GREEN/RED11 BLACK12 BROWN13 BROWN/RED14 WHITE

18

714

N/C

N/C

N/CN/CN/CN/CN/C

N/CN/C

N/C

A

OL-H

RN-R

S-NI

8(B)

Connect PINK wires when using OL-HRN-RS-NI8(B) harness

BROWN - OEM Horn (-) Output

Door Lock Option A

Door Lock Option B

CAN Option A

CAN Option B

OPTIONALOEM Horn


A

CB




OL-HRN-RS-NI8(A)


DO NOT CONNECT

BLACK - Ground

Body Control Module

DO NOT CONNECT

DO NOT CONNECT

VEHICLE’S OBDII

CONNECTOR


OPTIONAL

DE

HJ

FGK L



Nissan Altima Push-to-Start Sedan Automatic 2019 - 2021


Horn BLACK 16 10 VIOLET (-) Horn Switch On Column


Nissan Qashqai Push-to-Start 4 Cyl. Automatic 2017 - 2020
















Nissan Rogue Sport Push-to-Start 4 Cyl. Automatic 2017 - 2020












DATA CABLE

RS-X70 Diagram #2

G

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

N/CN/CN/C

C

B



18

714

N/C

N/C

N/CN/CN/CN/CN/C

N/CN/C

N/C

A

Door Lock Option A

Door Lock Option B

CAN Option B

CAN Option A

OL-H

RN-R

S-NI

8(B)


BROWN - OEM Horn (-) OutputOPTIONAL

OEM Horn


A

OL-HRN-RS-NI8(A)


DO NOT CONNECT

BLACK - Ground

VEHICLE’S OBDII

CONNECTOR

RED/WHITE - Trunk Release (-) OutputOPTIONAL

CB





Body Control Module


DE

HJ

FGK L



















DATA CABLE

RS-X70 Diagram #3

G

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

N/CN/CN/C

C

B



18

714

N/C

N/C

N/CN/CN/CN/CN/C

N/CN/C

N/C

A

Door Lock Option A

Door Lock Option B

CAN Option B

CAN Option A

CONNECT

CB





Body Control Module

OL-H

RN-R

S-NI

8(B)



OEM Horn


A

OL-HRN-RS-NI8(A)

OL-HRN-RS-NI8(D)DL-NI8/9BLACK -

Ground

VEHICLE’S OBDII

CONNECTOR


OPTIONAL

DE

HJ

FGK L



Infiniti QX50 Push-to-Start Automatic 2019 - 2020


Horn WHITE 100 18 GRAY (-) Driver Kick Panel






DATA CABLE

RS-X70 Diagram #4

G

DPIN COLOR

1 BLUE2 RED3 GREEN3

1

N/CN/CN/C

C

B



18

714

N/C

N/C

N/C

N/CN/CN/C

N/CN/C

N/C

A

CONNECT

Door Lock Option B

Door Lock Option A

CAN Option B

CAN Option A

CB





Body Control Module

OL-H

RN-R

S-NI

8(B)



OEM Horn


A

OL-HRN-RS-NI8(A)

OL-HRN-RS-NI8(D)DL-NI8/9BLACK -

Ground

VEHICLE’S OBDII

CONNECTOR

RED/WHITE - Trunk Release (-) OutputTrunk Release

OPTIONAL

DE

HJ

FGK L


MODEL: OL-HRN-RS-NI8RS-X70 Optional Accessories

YELLOW - Alarm notifi cation input (+/-)

Antenna Cable

Push-Button LED Cable

F Antenna/LED Cable OR

Mod

el: L

INKR

-LT

ww

w.o

meg

alin

kr.c

om

G

G OL-ADAPTOR-B2G DATA CABLE

DATA CABLE

OR

G SENSOR CABLE

BLACK

GREEN

Data ShockSensorBLACK

RS-X70 MUST have V1.4 or newer fi rmware for Linkr-LT compatibility.


MODEL: OL-HRN-RS-NI8Installation Mode Selection

Module Programming

Press & hold programming button until LED turns solid GREEN to register selection.

2Press & release programming button to select installation mode.

LED flash (1x) once = Data Mode (Recommended)LED flashes (2x) twice = Hardwire Mode

1

Module Programming (cont.)

OR




4

Wait, the LED will turn solid RED, then solid GREEN for 1 second, then solid RED.

3

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

5 Turn the ignition to the ON position.

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

If LED flashes GREEN rapidly proceed with step 7. If LED turns solid GREEN for 2 seconds proceed to step 13.

WARNING:Disconnect power lastDisconnect module from vehicle.

WARNING: Do not press module programming button. Connect power first.Connect all other module connectors

10

Connect module to computer and proceed with extended programming.9

8

Turn the ignition to the OFF position.7

Proceed to RS-X70 Programming/Vehicle Learn.



14

Wait, the LED will turn solid GREEN for 2 second.

12

13

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

6

2



RS-X70 Programming/Vehicle Learn V1.6 (see installation guide for older versions)

Before You Begin:- Make sure all wires/harnesses are connected.- Program the bypass module to the vehicle per the instructions on the previous pages.- Connect any additional accessories/modules to the data ports.- MANUAL TRANSMISSION VEHICLES ONLY: Set the parking brake. The BLACK/WHITE wire must be connected to the parking brake wire.

Within 5 seconds of step 1 press the Valet button 3x or send remote start command (by remote, Linkr, activa-tion input wire etc.).

- The system will chirp & fl ash lights to indicate crankdelay (Default: 1 chirp/fl ash = 1.5 sec)

- Press valet button to change crank delay- Chirps: 1=1.5 sec, 2=15 sec, 3=20 sec, 4=30 sec

2

Programming complete.8

MANUAL TRANSMISSIONS: Release the parking brake.

AUTOMATIC TRANSMISSIONS: Turn the ignition key OFF.

- The system will chirp & fl ash the lights equal the #of IGN/ACC/START circuits detected (Max: 4).

MANUAL - Proceed to step 5.AUTOMATIC - Skip to step 6.

4

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON Turn ignition to ON position (do not start).1

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON Start the engine with the key and let the engine reach normal idle.

3

TO SAVE SETTINGS/FINISH VEHICLE LEARN: Press the BRAKE pedal (will shut down RS).

- This disables VEHICLE LEARN (to enable again, programinstaller feature #2 (bank 10) to “Enabled”.

TO CANCEL/START OVER: Press the valet button once.

7

5 MANUAL TRANSMISSIONS: Set the parking brake again to enter Manual Transmission Reservation Mode option selection. (installer feature #11)

- The system will chirp & fl ash the light to indicate currentsetting (default: 2 - Off)

- Set and Release the parking brake to scrool through settingoptions.

- Chirp confi rmation: 1 = ON - Shutdown w/ lock, 2 = OFF,3 = ON - Shutdown w/ door close, 4 = ON - Shutdown 10sec. after door close

- Before turning the key OFF, perform the MT reservationsequence (see operation guide) and exit the vehicle.

6

TroubleShooting

- See system installation guide for remote start diagnostics and troubleshooting.- See OmegaLink module/fi rmware guide at www.wiresheet.com for interface module diagnostics and troubleshooting.

OR

Activate remote start (within 60 sec. of Step 4 or 5). Wait until engine is running and LED fl ashes slowly (10-45 seconds after engine cranks & runs).Push-to-Start vehicles: Ensure the OEM fob is at least 20 ft. away to allow remote start.

- The system will detect data protocols, select the bestavailable engine running detection method, and, learn anyavaialble tach input (data or analog).

3x

2x

2x


MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Layout

A B

E F G H

C D

INSTALLATION STEPS:1) Go to OmegaWeblink.com or use WebLink Mobile to flash the OL-MDB-ALL with the firmware matching the vehicle.

NOTE: If OEM remote is being used to activate the remote start be sure to enable “Factory keyless RS sequence” as “Lock + Lock + Lock” OR “Lock + Unlock + Lock”2) Make all the connections shown in the diagram on the following pages.3) Connect any optional RF kit or telematics device as needed.4) Program the OL-MDB-ALL to the vehicle (see “Module Programming” on the following pages).

NOTE: If an Omegalink RF (OL-RF-XX-SST) is used you will need to program the remotes at this time, Excalibur RF (RFK-XX-SST) kits will be pre-programmed from the factory.5) Test the system for all desired functions.

F WHITE 3 PIN

G WHITE 7 PIN

H WHITE 6 PIN

A BLACK 4 PIN DATA PORT

B BLACK 10 PIN

C PROGRAMMING/STATUS LED

D PROGRAMMING/RESET BUTTON

E BLUE 3 PIN

OL-MDB-ALL as Stand-Alone Installation Steps



Nissan Rogue Push-to-Start 4 Cyl. Automatic 2014 - 2016Body Control Module - - - - - Under Driver Side Dash


Nissan Rogue Std. Key 4 Cyl. Automatic 2014 - 2016Body Control Module - - - - - Under Driver Side Dash





MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Diagram #1

PIN COLOR1 GREEN/BLACK2 BLUE/BLACK3 RED/WHITE4 BROWN5 VIOLET/YELLOW6 VIOLET/BLACK7 WHITE8 BLACK/WHITE9 GREEN

10 VIOLET/WHITE N/C

N/CN/CN/CN/CN/CN/CN/C

1

10

B

Optional RF Kit/Telematics Port

DO NOT CONNECT

HOOD PIN Note: If vehicle is NOT equipped with a factory hood pin connect GREEN/BLACK wire to installed hood pin

OL-HRN-RS-NI8(C)RS-NI8/9

Door Lock Option A

Door Lock Option B

CAN Option A

CAN Option B

CB




OL-HRN-RS-NI8(A) Body Control Module

DO NOT CONNECT

DO NOT CONNECT

VEHICLE’S OBDII

CONNECTOR

ORANGE/WHITE - Trunk Release (-) OutputPower Liftgate

OPTIONAL

DE

HJ

FGK L



Nissan Altima Push-to-Start Sedan Automatic 2019 - 2021Body Control Module - - - - - Under Driver Side Dash


Nissan Qashqai Push-to-Start 4 Cyl. Automatic 2017 - 2020Body Control Module - - - - - Under Driver Side Dash


Nissan Qashqai Std. Key 4 Cyl. Automatic 2017 - 2018Body Control Module - - - - - Under Driver Side Dash


Nissan Rogue Push-to-Start 4 Cyl. Automatic 2017 - 2020Body Control Module - - - - - Under Driver Side Dash




Nissan Rogue Sport Push-to-Start 4 Cyl. Automatic 2017 - 2020Body Control Module - - - - - Under Driver Side Dash


Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2017 - 2018Body Control Module - - - - - Under Driver Side Dash





MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Diagram #2


10 VIOLET/WHITE N/C


1

10

B


DO NOT CONNECT



Door Lock Option A

Door Lock Option B

CAN Option B

CAN Option A

OL-HRN-RS-NI8(A)

VEHICLE’S OBDII

CONNECTOR

ORANGE/WHITE - Trunk Release (-) OutputOPTIONAL

CB





Body Control Module


DE

HJ

FGK L



Nissan Qashqai Std. Key 4 Cyl. Automatic 2019 - 2020Body Control Module - - - - - Under Driver Side Dash




Nissan Rogue Sport Std. Key 4 Cyl. Automatic 2019 - 2020Body Control Module - - - - - Under Driver Side Dash







10 VIOLET/WHITE N/C


1

10

B


OL-MDB-ALL as Stand-Alone Diagram #3

CONNECT



Door Lock Option A

Door Lock Option B

CAN Option B

CAN Option A

OL-HRN-RS-NI8(A)

VEHICLE’S OBDII

CONNECTOR

ORANGE/WHITE - Trunk Release (-) OutputPower Liftgate

OPTIONAL

CB





Body Control Module

DE

HJ

FGK L



Infiniti QX50 Push-to-Start Automatic 2019 - 2020Body Control Module - - - - - Under Driver Side Dash







10 VIOLET/WHITE N/C


1

10

B


OL-MDB-ALL as Stand-Alone Diagram #4

CONNECT



Door Lock Option B

Door Lock Option A

CAN Option B

CAN Option A

CB





Body Control Module

OL-HRN-RS-NI8(A)

VEHICLE’S OBDII

CONNECTOR

Trunk Release

DE

HJ

FGK L


MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Optional Accessories

YELLOW - Alarm notification input (+/-) Mod

el: L

INKR

-LT

ww

w.o

meg

alin

kr.c

om

DATA CABLE

OL-MDB-ALL MUST have be flashed for Linkr compatibility

ADAPTOR Antenna Cable

OL-MDB-ALL MUST have be flashed for Excalibur RF Kit compatibility



H-OLRF4B Antenna Cable

OL-MDB-ALL MUST have be flashed for Omegalink RF Kit compatibility

Optional RF Kit/Telematics Port RED & BLACK - Not Used

RED & BLACK - Not Used

Not Used

OL-HRN-LINKR-ALL


MODEL: OL-HRN-RS-NI8OL-MDB-ALL as Stand-Alone Module Programming

OR




4

Wait, the LED will turn solid RED, then solid GREEN for 1 second, then solid RED.

3

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

5 Turn the ignition to the ON position.

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

If LED flashes GREEN rapidly proceed with step 7. If LED turns solid GREEN for 2 seconds proceed to step 13.

WARNING:Disconnect power lastDisconnect module from vehicle.

WARNING: Do not press module programming button. Connect power first.Connect all other module connectors

10

Connect module to computer and proceed with extended programming.9

8

Turn the ignition to the OFF position.7 Proceed to RS-X70 Programming/Vehicle Learn.



14

Wait, the LED will turn solid GREEN for 2 second.

12

13

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

ENGINESTARTSTOP

ENGINESTARTTTSTOP

OFF ACC STARTON

6

2

Documents

MODEL NI8 AL-XX70-B RS-X70 20210302 AVAILABLE …