PAGE 1 OF 2

MODEL L-75S DIAGRAM WITH HINGED TOP GUIDES

NOTES:1. THE CABINET BOX SHOWN IN THE DIAGRAM IS FOR REFERENCE ONLY AND IS NOT PROVIDED WITH THE LIFT SYSTEM2. FOR THIS LIFT MODEL, THE LENGTH OF ITS TRAVEL [EXTENSION LENGTH OR STROKE] IS 52"3. FOR THIS LIFT MODEL, THE TOTAL WEIGHT CAPACITY IS 130 LBS4. THIS LIFT MODEL MANUALLY ROTATES 180 DEGREES IN BOTH DIRECTIONS WITH A LOCKING HOME POSITION5. LIFT WILL NOT OPERATE WHEN SWIVELED6. HEIGHT OF THIS MODEL IS ADJUSTABLE IN 1/4" INCREMENTS UP TO 8” [MINIMUM HEIGHT = 37.8"; MAXIMUM HEIGHT = 45.8"]7. WHEN INSTALLED IN THE FLOOR, THE LID MUST BE SUPPORTED BY CATCHES8. THE LIFT MUST BE FASTENED TO THE FLOOR AND REAR WALL OF THE ENCLOSURE FOR OPTIMAL STABILITY AND SAFETY9. WHEN DETERMINING TV HEIGHT, ALWAYS USE MANUFACTURER SUPPLIED "TV WITHOUT STAND" HEIGHT10. LIFT MECHANISM IS POWDERCOATED BLACK STEEL - COLORS IN DIAGRAM ARE FOR CLARITY ONLY

IMPORTANT HINGED LID INFORMATION1. HINGED LIDS REQUIRE THE USE OF THE “HINGED TOP GUIDE” ACCESSORY. THESE GUIDES ARE MOUNTED OT THE TOP OF THE LIFT SYSTEM AND WILL PUSH THE LID OPEN AS THE LIFT EXTENDS. WHEN THE LIFT IS LOWERED, THE LID CLOSES BY GRAVITY. PLEASE NOTE: THE LID MUST NOT OPEN BEYOND 90 DEGREES.2. HINGES FOR THE LID ARE NOT PROVIDED BY NEXUS 213. FOR THE HINGED LID TO FUNCTION PROPERLY YOU MUST ALLOW AT LEAST 2” OF SPACE BETWEEN THE PIVOT POINT OF THE HINGE AND THE BACK OF THE LIFT SYSTEM. PLEASE BE AWARE SOME HINGE STYLES - SUCH AS EUROPEAN HINGES - MAY INCREASE THE OVERALL DEPTH THAT IS REQUIRED INSIDE THE CABINET. PLEASE CALL US IF YOU HAVE ANY QUESTIONS.

ALL CALCULATIONSASSUME 3/4" MATERIAL

FOR THE LID

1" MINIMUM CLEARANCE

INTERIOR ENCLOSURE WIDTH = TV WIDTH + 2"

BOTTOM OF TVRETRACTED GAP

TV FOR REFERENCE[NOT PROVIDED]

1" MINIMUMCLEARANCE

INTERIOR ENCLOSUREDEPTH =

TV DEPTH + 9.85"OR 11.75",

WHICHEVER ISGREATER

MINIMUM LID DEPTH= TV DEPTH + 9.85"

RECOMMENDEDBLOCK DEPTH = 3"

RECOMMENDEDBLOCK DEPTH = 3"

HINGED LIDPIVOT POINT

FOR INTERIOR ENCLOSURE HEIGHTSEE IMPORTANT DIMENSIONS TABLE

ON PAGE 2

COPYRIGHT 2017 - ALL RIGHTS RESERVEDUPDATED 04/12/18

TV TO SURFACE GAP[TO GUARANTEE SWIVEL FUNCTION

WITHOUT INTERFERENCE]

BOTTOM OF TVMUST CLEAR THETOP OF THE LIDWHEN HINGED

UPWARDSTV MUST CLEAR CENTER RISER

TO SWIVEL, SEE TABLE FORTRAVEL REQUIREMENTS AND

OTHER IMPORTANT DIMENSIONS

L-75S IMPORTANT DIMENSIONS TABLE

TV Height

Interior Enclosure

Height

Bottom of TV Retracted

Gap

Travel Required to

Swivel

TV to Surface

Gap

29” 38” 8.375” 34.25” -

FLUSH30” 38” 7.375” 36” -

31” 38” 6.375” 36.25” -

32” 38” 5.375” 38.25” 2.25”

33” 39” 5.375” 40.25” 1.25”

GAP

34” 39” 4.375” 40.25” 3.25”

35” 39” 3.375” 42.25” 5.25”

36” 40” 3.375” 44.25” 4.25”

37” 41” 3.375” 44.25” 3.25”

38” 41” 2.375” 44.25” 5.25”

39” 42” 2.375” 46.25” 4.25”

40” 43” 2.375” 46.25” 3.25”

41” 44” 2.375” 46.25” 2.25”

42” 45” 2.375” 46.25” 1.25”

43” 46” 2.375” 46.25” - FLUSH

PAGE 2 OF 2

MODEL L-75S DIAGRAM WITH HINGED TOP GUIDES

NOTES:1. ‘FLUSH’ ENTRIES ARE TV HEIGHTS AND ENCLOSURE HEIGHTS THAT WILL ALLOW FOR THE BOTTOM TV TO BE FLUSH WITH THE SURFACE AND STILL SWIVEL2. ‘GAP’ ENTRIES ARE TV HEIGHTS AND ENCLOSURE HEIGHTS THAT WILL REQUIRE A GAP BETWEEN THE BOTTOM OF TV AND THE SURFACE, WHEN EXTENDED, IN ORDER TO SWIVEL3. CABINETS CAN BE BUILT FOR FLUSH SWIVELING BY ADDING THE 'TV TO SURFACE GAP', THE 'INTERIOR ENCLOSURE HEIGHT' VALUE, AND THE TOP MATERIAL THICKNESS VALUE4. SEE DIAGRAM TO THE LEFT FOR CLARIFICATION OF 'TV TO SURFACE GAP'

COPYRIGHT 2017 - ALL RIGHTS RESERVEDUPDATED 04/12/18