MODEL: 1893 / 1893-11" IMPACT WRENCH

SPECIFICATIONS

Important Warnings - Impacts 1. Eye protection and hearing protection and safety gloves must always be worn when operating an impact wrench or impact

driver.

2. When using heavy impact sockets or sockets on impact wrenches with 3/4” drive anvils or larger, a socket retaining ring and pin should be used to prevent the socket falling off and causing injury.

3. Use only impact sockets and accessories. Only use sockets designated “FOR USE WITH IMPACT WRENCHES”, hand tool

damage and replace when necessary. Accessory Hazards

4. Disconnect the assembly power tool for threaded fasteners from the energy supply before changing the inserted tool or accessory.

5. Do not touch sockets or accessories during impacting as this increases the risk of cuts, burns or vibration injuries.

6. Use only sizes and types of accessories and consumables that are recommended by the assembly power tool for threaded fasteners manufacturer; do not use other types or sizes of accessories and consumables.

Model No. Free Speed (RPM)

Bolt Capacity (in.)

Square Drive (in.)

Impacts Per Minute

Max. Torque (ft-lb) @90 psi

Weight (lbs.)

Length (in)

Air Cons. (CFM)

Rec. Hose Size (in.)

Air Inlet (in.)

1893 5,000 1-1/4 1 x 8 1400 1800 26 22.0 12 1/2 1/2 NPT

1893-1 5,000 1-1/4 1 1400 1800 23.25 14.0 12 1/2 1/2 NPT

Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will cause damage to the tool. Drain the air tank daily. Clean the air inlet �lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed in the illustration below. The air inlet, used for connecting air supply, has standard 1/4” NPT American Thread. Line pressure should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and �ttings should have the same inside dimensions.

Air Supply

MODEL: 1893 / 1893-11" IMPACT WRENCH

Exploded View & Parts List

Ref #

Part Number Description Qty Ref #

Part Number Description Qty.

1 947-407101-AC Motor Housing - Aircat 1 22 9OR01608204 O-Ring 1

2 9PN04002308 Pin 1 23 943-403323 Spring 1

3 947-407103 Air Inlet 1 24 943-403324 Pin 1

4 947-407304 Trigger 1 25 947-407125 Anvil Bushing 1

5 947-407105 Valve Stem 1 27 9SP04001000 Spring Pin 1

6 947-407106 Reverse Valve Bushing 1 28 947-407128 Hammer Case 1

7 9OR01908204 O-Ring 1 29 947-407135 Gasket 1

8 943-403147 Valve Spring 1 30 947-407130-12 Screw 8

9 9OR00705305 O-Ring 1 32 947-407112 Side Plate 1

10 961902 Spring Pin 2 33 947-407108 Hammer Frame 1

11 947-407134 Gasket 1 34 947-407109 Hammer Cam 1

12 947-407220-AC Rear Cover - Aircat 1 35 947-407111 Hammer 1

13 90610146 Ball Bearing 1 36 947-407102 Anvil 1

14 947-407114 Rear End Plate 1 947-4071L02-91 Anvil (1" L=9") 1

15 947-407115 Rotor 1 37 910211 O-Ring 1

16 947-407116 Rotor Blade 6 38 947-405112 Retainer Ring 1

17 9SP06001800 Spring Pin 2 39 940317-14 Spring Pin 1

18 947-407118 Cylinder 1 40 947-407160 Dead Handle 1

19 947-407119 Front End Plate 1 41 97H-753528 Screw 4

20 906205Z Ball Bearing 1 43 910018 Hex. Key Wrench 1

21 947-407121 Air Regulator 1 46 947-407146 Valve Bushing 1

SERVICE CENTER LISTINGS ENCLOSED

AIRCAT and NITROCAT air tools are warranted to be free from defects in material and workmanship for 2 years from date of purchase. We will repair or replace; at our option any defective part or unit which proves to be defective in material or workmanship during this 2 year period. The foregoing obligation is AIRCAT and Florida Pneumatic's sole liability under this or any implied warranty, under no circumstances shall it be liable for any incidental or consequential damages.

This warranty applies to the tool only. The warranty does not apply to any attached accessories/consumable products; such as drill chucks, sander backing pads, air hammer retainers and chisels or “kit” accessories or any other accessory included with the tool.

an AIRCAT or Florida Pneumatic Authorized Service Center) are not covered by this warranty.

Return your tool to an AIRCAT or Florida Pneumatic Authorized Service Center freight prepaid. Be sure to include your name, address, copy of purchase with date and description of the suspected defect.

AIRCAT whose policy is continued product improvement reserves the right to make changes in design or construction at any time without incurring any obligation on tools previously sold.

Tune-Up and Head Kits for all AIRCAT PNEUMATIC impact wrenches and ratchets are available.

For Authorized Service Centers, please visit www.aircat.com/warranty-service