MNL-X7SPT-DF-D525 - ICH9 - Motherboard - Super Micro … · 2016. 7. 1. · Manual Revision 1.0 Release Date: February 22, 2011 Unless you request and receive written permission from

X7SPT-DF-D525

Revision 1.0

Manual Revision 1.0

Release Date: February 22, 2011

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.

Copyright © 2011 by Super Micro Computer, Inc. All rights reserved. Printed in the United States of America

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software and docu-mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.

IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.

WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.

iii

Preface

About This Manual

This manual is writ ten for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the

X7SPT-DF-D525 motherboard. This product is intended to be profession-ally installed and serviced by a technician.

About This Motherboard

The X7SPT-DF-D525 motherboard is a uni-processor twin motherboard. Featuring two nodes on the same board, it is a great choice for system builders who need more computing power in the same space required for most single node solutions.

Each node of the X7SPT-DF-D525 is equipped with the Intel ATOM D525 (Dual Core, 1.8GHz, 13W) processor and offer several configuration choices, including memory up to 4GB (non-ECC SO-DIMM), up to 3 SATA ports, an on-board VGA, and up to 4 USB 2.0 ports.

Manual Organization

Chapter 1 describes the features, specifications and performance of the mainboard and provides detailed information about the chipset.

Chapter 2 provides hardware installation instructions. Read this chapter when in-stalling the processor, memory modules and other hardware components into the system. If you encounter any problems, see Chapter 3, which describes trouble-shooting procedures for video, memory and system setup stored in the CMOS.

Chapter 4 includes an introduction to the BIOS and provides detailed information on running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Codes.

Appendix B lists Driver Installation Instructions.

Preface

iv

X7SPT-DF-D525 User’s Manual

Conventions Used in the Manual:

Special attention should be given to the following symbols for proper installation and to prevent damage done to the components or injury to yourself:

Danger/Caution: Instructions to be strictly followed to prevent catastrophic system failure or to avoid bodily injury

Warning: Critical information to prevent damage to the components or data loss.

Important: Important information given to ensure proper system installa-tion or to relay safety precautions.

Note: Additional Information given to differentiate various models or pro-vides information for correct system setup.

v

Contacting Supermicro

Contacting Supermicro

HeadquartersAddress: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

EuropeAddress: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-PacificAddress: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: 886-2-8228-1366, ext.132 or 139

vi


Table of Contents

PrefaceAbout This Manual ........................................................................................................ iiiAbout This Motherboard ................................................................................................ iiiManual Organization ..................................................................................................... iiiConventions Used in the Manual: .................................................................................ivContacting Supermicro ...................................................................................................v

Chapter 1 Introduction1-1 Overview ......................................................................................................... 1-1

Checklist .......................................................................................................... 1-1 X7SPT-DF-D525 Image .............................................................. 1-2Motherboard Layout ........................................................................................ 1-3Quick Reference ............................................................................................. 1-4Motherboard Features ................................................................................... 1-7X7SPT-DF-D525 Series Block Diagram ......................................................... 1-9

1-2 Chipset Overview ......................................................................................... 1-10I/O Controller Hub: ICH9R ............................................................................ 1-10

1-3 PC Health Monitoring .....................................................................................1-11Recovery from AC Power Loss ......................................................................1-11Onboard Voltage Monitoring .........................................................................1-11Fan Status Monitor with Software ..................................................................1-11CPU Overheat LED and Control ...................................................................1-11

1-4 Power Configuration Settings........................................................................ 1-12Slow Blinking LED for Suspend-State Indicator ........................................... 1-12BIOS Support for USB Keyboard.................................................................. 1-12Main Switch Override Mechanism ................................................................ 1-12

1-5 Power Supply ................................................................................................ 1-121-6 Super I/O ....................................................................................................... 1-131-7 Overview of the Nuvoton BMC Controller ..................................................... 1-131-8 Node Hot-Swapping ...................................................................................... 1-14

Chapter 2 Installation2-1 Static-Sensitive Devices .................................................................................. 2-1

Precautions ..................................................................................................... 2-1Unpacking ....................................................................................................... 2-1Tools Needed .................................................................................................. 2-2Location of Mounting Holes ............................................................................ 2-2

2-2 Motherboard Installation .................................................................................. 2-2

vii

Table of Contents

Installation Instructions .................................................................................... 2-32-3 System Memory .............................................................................................. 2-4

How to Install SO DIMMs ............................................................................... 2-4Memory Support .............................................................................................. 2-4The SO DIMM Socket ..................................................................................... 2-5

2-4 Back Panel I/O Ports & Switches ................................................................... 2-6Back Panel Connectors and I/O Ports ............................................................ 2-6

Universal Serial Bus (USB) ........................................................................ 2-7LAN Ports / IPMI ........................................................................................ 2-8VGA Connector .......................................................................................... 2-9Rear UID (Unit ID) Switch ........................................................................ 2-10

2-5 Header Connections .....................................................................................2-11Serial Ports (JKCOM/JCOM) - OEM Option .............................................2-11Universal Serial Bus (JUSB/JKUSB) ........................................................ 2-12Front Panel Accessible Add-on Card Header (JF2) ................................. 2-13Onboard Speaker (JKSP1/SP1) ............................................................... 2-14TPM Header (JTPM/JKTPM) ................................................................... 2-14SMB (JSMB1/JKSMB1) ............................................................................ 2-15SATA DOM Power - OEM Option ............................................................ 2-15

2-6 Jumper Settings ............................................................................................ 2-16Explanation of Jumpers ............................................................................ 2-16LAN Port Enable/Disable (JPL/JKPL) ...................................................... 2-17BMC Enable/Disable (JPB/JKPB) ............................................................ 2-17CMOS Clear (JBT1/JKBT1) ..................................................................... 2-18Watch Dog Timer Enable/Disable (JWD1/JKWD1) .................................. 2-18

2-7 Onboard Indicators ........................................................................................ 2-19LAN Port LEDs ......................................................................................... 2-19Unit ID LEDs (LE2/LKE2) ......................................................................... 2-20Main Power LED (LE1/LKE1)................................................................... 2-20Power/Suspend LED (DP2/DKP2) ........................................................... 2-20SATA LED (DKP3/DP3) ............................................................................ 2-21BMC Heartbeat LED (DKP1/DP1) ............................................................ 2-21

2-8 Serial ATA Ports ............................................................................................ 2-22SATA Connectors ..................................................................................... 2-22

Chapter 3 Troubleshooting3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ............................................................................................ 3-1No Power ........................................................................................................ 3-1No Video ......................................................................................................... 3-1

viii


Memory Errors ............................................................................................... 3-2Losing the System’s Setup Configuration ....................................................... 3-2

3-2 Technical Support Procedures ........................................................................ 3-23-3 Frequently Asked Questions ........................................................................... 3-33-4 Returning Merchandise for Service................................................................. 3-5

Chapter 4 BIOS 4-1 Introduction ...................................................................................................... 4-1

Starting BIOS Setup Utility .............................................................................. 4-1How To Change the Configuration Data ......................................................... 4-1How to Start the Setup Utility ......................................................................... 4-2

4-2 Main Setup ...................................................................................................... 4-2System Overview: The following BIOS information will be displayed: ....... 4-3System Time/System Date ........................................................................ 4-3Processor ................................................................................................... 4-3System Memory ........................................................................................ 4-3

4-3 Advanced Setup Configurations...................................................................... 4-4BOOT Feature.............................................................................................. 4-4

Quick Boot .................................................................................................. 4-4Quiet Boot .................................................................................................. 4-4AddOn ROM Display Mode ........................................................................ 4-4Bootup Num-Lock ....................................................................................... 4-5Wait For 'F1' If Error ................................................................................... 4-5Hit 'Del' Message Display .......................................................................... 4-5Watch Dog Function ................................................................................... 4-5Power Button Function ............................................................................... 4-5Restore on AC Power Loss ........................................................................ 4-5Interrupt 19 Capture ................................................................................... 4-5EUP Support .............................................................................................. 4-5

CPU Configuration ....................................................................................... 4-6Clock Spread Spectrum ............................................................................. 4-6Max CPUID Value Limit.............................................................................. 4-6Execute-Disable Bit Capability (Available when supported by the OS and the CPU) ..................................................................................................... 4-6Hyper-threading Technology ....................................................................... 4-6

Advanced Chipset Control ........................................................................... 4-6

Northbridge Configuration............................................................................ 4-6DRAM Frequency ....................................................................................... 4-6Configure DRAM Timing by SPD ............................................................... 4-6DRAM CAS# Latency ............................................................................... 4-7

ix

Table of Contents

DRAM RAS# to CAS# Delay .................................................................... 4-7DRAM RAS# Precharge ............................................................................. 4-7DRAM RAS# Activate to Precharge .......................................................... 4-7Internal Graphics Mode Select ................................................................... 4-7Active State Power Management ............................................................... 4-7USB Functions ........................................................................................... 4-7Legacy USB Support (available if USB Functions above is Enabled)....... 4-7USB Controller ........................................................................................... 4-7

IDE/SATA Configuration ............................................................................... 4-8SATA#1 Configuration ................................................................................ 4-8SATA#2 Configuration (Available if IDE is enabled under "Configure SATA#1 as" above) .................................................................................... 4-8IDE Detect Timeout (sec) ........................................................................... 4-8Primary IDE Master/Slave,Secondary IDE Master/Slave .......................... 4-8

PCI/PnP Configuration .............................................................................. 4-10Clear NVRAM ........................................................................................... 4-10Plug & Play OS ........................................................................................ 4-10PCI Latency Timer .....................................................................................4-11PCI IDE Bus Master ..................................................................................4-11ROM Scan Ordering ..................................................................................4-11Load Onboard LAN 1 Option ROM/ Load Onboard LAN 2 Option ROM .4-11

Super IO Device Configuration .................................................................4-11Serial Port1 Address/ Serial Port2 Address ..............................................4-11

Remote Access Configuration ...................................................................4-11Remote Access ........................................................................................4-11

Hardware Health Configuration .......................................................4-12CPU Overheat Alarm ................................................................................ 4-12CPU Temperature ..................................................................................... 4-13System Temperature ................................................................................ 4-13FAN1/FAN2 Speed ................................................................................... 4-14Fan Speed Control Modes ....................................................................... 4-14CPU Vcore, AVCC, 3.3Vcc, 12V, V_DIMM, 5V, -12V, 3.3Vsb, and Vbat 4-15

ACPI Configuration .................................................................................... 4-15High Performance Event Timer ................................................................ 4-15USB Device Wakeup from S3/S4 ............................................................ 4-15ACPI Aware O/S ....................................................................................... 4-15Suspend Mode ......................................................................................... 4-15

x


AMI OEMB Table ...................................................................................... 4-15ACPI APIC Support .................................................................................. 4-16APIC ACPI SCI IRQ ................................................................................. 4-16Headless Mode ........................................................................................ 4-16ACPI Version Features ............................................................................. 4-16

IPMI Configuration ..................................................................................... 4-16IPMI Firmware Revision ........................................................................... 4-16Status of BMC .......................................................................................... 4-16IPMI Function ........................................................................................... 4-16View BMC System Event Log .................................................................. 4-16Clear BMC System Event Log ................................................................. 4-17Set LAN Configuration ............................................................................. 4-17BMC Watch Dog Timer Action ................................................................. 4-18

Event Log Configuration ............................................................................ 4-18View Event Log ........................................................................................ 4-18Mark all events as read ............................................................................ 4-18Clear event log ......................................................................................... 4-18

4-4 Security Settings ........................................................................................... 4-19Supervisor Password .............................................................................. 4-19User Password: ........................................................................................ 4-19Change Supervisor Password .................................................................. 4-19Change User Password ........................................................................... 4-20Boot Sector Virus Protection .................................................................... 4-20

4-5 Boot Settings ................................................................................................ 4-21Hard Disk Drives ........................................................................................ 4-21Removable Drives ...................................................................................... 4-22

Retry Boot Devices .................................................................................. 4-22

4-6 Exit Options ................................................................................................... 4-22Save Changes and Exit ........................................................................... 4-22Discard Changes and Exit ...................................................................... 4-23Discard Changes ...................................................................................... 4-23Load Optimal Defaults .............................................................................. 4-23Load Fail-Safe Defaults ............................................................................ 4-23

xi

Appendix A POST Error Beep CodesRecoverable POST Error Beep Codes ......................................................................A-1

Appendix B Software Installation InstructionsB-1 Installing Drivers ..............................................................................................B-1B-2 Configuring Supero Doctor III .........................................................................B-2

Table of Contents

xii


Notes

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

ChecklistCongratulations on purchasing your computer motherboard from an acknowledged leader in the industry. Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance. Please check with the system’s manual that all the parts have been included. If anything listed is damaged or missing, contact your retailer.

1-2


X7SPT-DF-D525 Image

Note: All graphics shown in this manual were based upon the latest PCB Revision available at the time of publishing of the manual. The motherboard you've received may or may not look exactly the same as the graphics shown in this manual.


1-3

Motherboard Layout

Important Notes

Jumpers not indicated are for •testing only. See Chapter 2 for detailed •information on jumpers, I/O ports and JF1 front panel connections. " " indicates the location of •"Pin 1".

MH8

MH7MH6

MH5

MH3

MH2

MH1

JKWF1

JWF1

1

3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC LE2AC

SKW1

SW1

UK67

J666

JKLAN

1

JLAN

1

JF2

JKTPM

19 20

JTPM

12

1920

JKDIMM1

JDIMM1

JKDIMM2

JDIMM2

E

JKPL2

JKPL1

JKWD

1

JKPB

JWD

1

JPB3

JPL1

JPL2

1

U39

DKP3

DKP2

DKP1

A

C

LKE1A C

LE1

DP2

SKP1+

SP1

+

JKBT1

JBT1

JKUSB2

JKUSB3

JUSB3

1

7

JUSB2

1

7

JKSMB1

JSMB1

JKCOM

1

JKCOM2JCOM1

JCOM2

5

JVGA

1

DP1

1-4


MH8

MH7MH6

MH5

MH3

MH2

MH1

JKWF1

JWF1

1

3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC LE2AC

SKW1

SW1

UK67

J666

JKLAN

1

JLAN

1

JF2

JKTPM

19 20

JTPM

12

1920

JKDIMM1

JDIMM1

JKDIMM2

JDIMM2

E

JKPL2

JKPL1

JKWD

1

JKPB

JWD

1

JPB3

JPL1

JPL2

1

U39

DKP3

DKP2

DKP1

A

C

LKE1A C

LE1

DP2

SKP1+

SP1

+

JKBT1

JBT1

JKUSB2

JKUSB3

JUSB3

1

7

JUSB2

1

7

JKSMB1

JSMB1

JKCOM

1

JKCOM2JCOM1

JCOM2

5

JVGA

1

DP1

9543 10

11

87

61 2

12

1415

16

18

1923

24

25

26

2728

29

30

31

45

50

13

32

33

41

4243

44

Quick Reference

17

20

21

22

35

36

137138139

140

47

46

49

48

51 52

34

CPUNode 2

CPUNode 1


1-5

Ports and Connectors

Number Connectors* Description3,8 JKVGA1, JVGA1 Video/Graphics Connector

4,9 JKLAN1/JKLAN2,JLAN1/JLAN2 RJ45 Connector for LAN1 and LAN2

5,10 JK666, J666 (top) IPMI Dedicated LAN13, 22 JCOM2,JKCOM2 Internal Serial Port (COM2)14, 23 JCOM1,JKCOM1 Internal Serial Port (COM1)17, 36 SKP1, SP1 Onboard Speaker24, 39 JKTPM, JTPM TPM Header25 U1/UK2 ICH927, 47 JSMB1, JKSMB1 System Management Bus header30 JDIMM1, JDIMM2 SO-DIMM Slots (Node 1)48 JKDIMM1, JKDIMM2 SO-DIMM Slots (Node 2)29 JF2 Hot Plug Connector19, 37 JKWF1, JWF1 SATA Disk on Module (DOM) Power21, 38 IKSATA1, ISATA1 SATA 1 Connector

20, 40 JKUSB2/JKUSB3, JUSB3/JUSB2 USB Headers

41, 42 BT1,BKT1 Onboard Battery51, 52 J666, JK666 (bottom) Back Panel USB 2.0 Ports (JUSB0/JUSB1, JKUSB0/JKUSB1)

*NOTE: All jumpers, connectors, LEDs with "K" in the name are for Node 2. The rest are for Node 1 or shared between the two.

Number LED* Description Color/State Status

2,6 LKE2, LE2 Unit ID LED Blue: Solid On UID On

28, 43 LE1,LKE1 3.3V Dual LED Green: Solid On PWR On

16, 31 DKP2, DP2 Power LED Green: Solid or BlinkingSolid On: Power OnBlinking: Suspend

15, 32 DKP3, DP3 SATA LED Green: Blinking SATA Drive Activity

45, 33 DKP1, DP1 BMC Heartbeat LED Green: Blinking BMC is active

LED Indicators

1-6


Jumper Descriptions

Number Jumper* Description Default Setting1,7 SKW1,SW1 Unit ID Switch Open11, 50 JPL2, JKPL2 LAN2 Enable/Disable Pins 1-2 (Enabled)12, 49 JPL1, JKPL1 LAN1 Enable/Disable Pins 1-2 (Enabled)

26, 44 JPB,JKPB BMC Enable/Disable Pins 1-2 (Enabled)Pins 2-3 (Disabled)

18, 35 JKWD1, JWD1 Watch Dog Timer ModePins 1-2 (Default)Pins 2-3 (NMI)

34, 46 JBT1,JKBT1 CMOS Clear (See Chapter 2)


1-7

Motherboard Features

Special Features

Twin motherboard with two nodes in one board

Processor (Each Node)Single Integrated Dual-Core Intel® ATOM™ D525 processor, 1.8 GHz, 13 Watts, 2 x 512KB L2 cache

Memory (Each Node) Supports up to 4GB of unbuffered 800MHz Non-ECC DDR3 SODIMMs in 2 •sockets (1.5V, 512MB, 1GB, 2GB)

Chipset (Each Node) Intel® ICH9R (South Bridge)•

Integrated Graphics (Shared) Matrox G200eW Graphics Accelerator•

BIOS 32 Mb AMI BIOS• ®, SPI Flash BIOS

PC Health MonitoringOnboard voltage monitors for CPU Cores, Chipset Voltage, Memory Voltage •+1.8V, +3.3V, +5V, +12V, +3.3V standby, +5V standby, VBat

Tachometer monitoring •Status monitor for speed control, on/off control•Temperature monitor for chassis, CPU environments•CPU thermal trip support•Supero Doctor III, Watch Dog/NMI•

PowerConfigurationACPI/ACPM Power Management•Keyboard wake-up from soft off•Fan auto-off in sleep mode•Power on mode for AC power recovery•

1-8


I/O Controllers and Ports (Each Node) Built-in ICH9R SATA Controller •Winbond Super I/O controller 83627DHG-P •One back panel VGA port•1 onboard SATA connector•3 SATA ports via Hot-Plug slot (Supports RAID 0/1/5/10)•Dual 10/100/1000 LAN ports (Intel 82574L)•One IPMI 2.0 with shared LAN ports•USB 2.0 ports & headers (USB1~USB6): Two ports on the back panel•One 20-pin TPM Header•Optimized for the Supermicro 2U chassis.•12VDC Power through Hot-Plug slot•OEM Options•

Two Fast 16550-compatible UART COM Ports (internal headers)xFour USB ports (on two headers)x

OtherLead free•

CD UtilitiesBIOS flash upgrade utility, Drivers and utilities for Intel® ICH9R chipset•

Dimensions6.8" x 16.4"•


1-9

X7SPT-DF-D525 Series Block Diagram

Note: This is a general block diagram. Please see the Motherboard Features pages for details on the features of the motherboard.

DC

PINEVIEW-D

SOD

IMM

1

SOD

IMM

2

DDR3 800

ICH9R

DMI

Intel 82574LGbE(LAN2)

Intel 82574LGbE(LAN1)

PCI-E x1

PCI-E x1

RJ45Dual

RJ45USBx2Combo

MDI

MDI

RMII

X7SPT-DF-D525

LPC

SATA GEN2x4

USB 2.0 x6

WPCM450BMC

128MBDDR2

PCI 33

SDRAM

W83627DHGSIO

COM 1Header

COM 2Header

D525

SATA Port 2

SATA Port 1

SATA Port 3

USBHeader x2

(4 Ports)

USBRearCONN

x2

BLOCK DIAGRAM

12V DC hot plug connectorUIDFAN PWM control

10/100EnetPHY

USBx2

SATA Port 4DOM

CK505CLK Generator

USB x2

TPM header

VGAconnt.

P5V VRM

P3V3VRM

P3V3_DUALVRM

P5V_DUAL

V_DIMMVRM

P1V5VRM

P1V05VRM

P1V8PLLVRM

VCCPVRM

RMII

Shared LAN

Dedicated LAN

1-10


1-2 Chipset Overview

I/O Controller Hub: ICH9RThe I/O Controller ICH9R provides the data buffering and interface arbitration re-quired for the system to operate efficiently. It also provides the bandwidth needed for the system to maintain its peak performance. The Direct Media Interface (DMI) provides the connection between the MCH and the ICH9R. The ICH9R supports up to six PCI-Express lanes, six Serial ATA (SATA) ports and twelve USB 2.0 ports. In addition, the ICH9R offers the Intel Matrix Storage Technology which provides various RAID options for data protection and rapid data access. It also supports the next generation of client management through the use of PROActive technology in conjunction with Intel's next generation Gigabit Ethernet controller.

Intel ICH9R System Features

The I/O Controller Hub provides the I/O subsystem with access to the rest of the system. Functions and capabilities include:

Advanced Power Management•

SMBus 2.0 (I• 2C)

SST/PECI Fan Speed Control•

SPI Flash•

Low Pin Count (LPC) Interface •


1-11

1-3 PC Health Monitoring

This section describes the PC health monitoring features of the X7SPT-DF-D525. The motherboard has an onboard System Hardware Monitor chip that supports PC health monitoring.

Recovery from AC Power LossBIOS provides a setting for you to determine how the system will respond when AC power is lost and then restored to the system. You can choose for the system to remain powered off (in which case you must hit the power switch to turn it back on) or for it to automatically return to a power on state. See the Power Lost Control setting in the BIOS chapter of this manual to change this setting. The default set-ting is Last State.

Onboard Voltage Monitoring The onboard voltage monitor will scan the following voltages continuously: CPU Cores, Chipset Voltage, Memory Voltage (+1.8V), +3.3V, +3.3V standby, +5V, +12V, and Vbat. Once a voltage becomes unstable, it will give a warning or send an error message to the screen. The User can adjust the voltage thresholds to define the sensitivity of the voltage monitor by using SD III.

Fan Status Monitor with SoftwareThe PC health monitor can check the RPM status of the cooling fans via Supero Doctor III.

CPU Overheat LED and Control This feature is available when the user enables the CPU overheat warning function in the BIOS. This allows the user to define an overheat temperature. When this temperature reaches the pre-defined threshold, the CPU thermal trip feature will be activated and it will send a signal to the Speaker LED and, at the same time, the CPU speed will be decreased.

1-12


1-4 PowerConfigurationSettings

This section describes features of your motherboard that deal with power and power settings.

Slow Blinking LED for Suspend-State IndicatorWhen the CPU goes into a suspend state, the chassis power LED will start blinking to indicate that the CPU is in suspend mode. When the user presses any key, the CPU will wake up and the LED will automatically stop blinking and remain on.

BIOS Support for USB KeyboardIf the USB keyboard is the only keyboard in the system, it will function like a normal keyboard during system boot-up.

Main Switch Override MechanismWhen an ATX power supply is used, the power button can function as a system suspend button. When the user presses the power button, the system will enter a SoftOff state. The monitor will be suspended and the hard drive will spin down. Pressing the power button again will cause the whole system to wake up. During the SoftOff state, the ATX power supply provides power to keep the required circuitry in the system "alive." In case the system malfunctions and you want to turn off the power, just press and hold the power button for 4 seconds. The power will turn off and no power will be provided to the motherboard.

1-5 Power Supply

As with all computer products, a stable power source is necessary for proper and reliable operation. It is even more important for processors that have high CPU clock rates of 1 GHz and faster.

The X7SPT-DF-D525 accommodates 12V power through its Hot-Plug port.


1-13

1-6 Super I/O

The Super I/O provides two high-speed, 16550 compatible serial communication ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable baud rate generator, complete modem control capability and a processor interrupt system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which sup-port higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Configuration and Power Interface), which includes support of legacy and ACPI power manage-ment through a SMI or SCI function pin. It also features auto power management to reduce power consumption.

1-7 Overview of the Nuvoton BMC Controller

The NuvotonSM Baseboard Management Controller (BMC), supports the 2D/VGA-compatible Graphics Core with the PCI interface, Virtual Media, and Keyboard/Video/Mouse (KVM) Redirection modules.

The Nuvoton BMC interfaces with the host system via a PCI interface to commu-nicate with the graphics core. It supports USB 2.0 and 1.1 for remote keyboard/mouse/virtual media emulation. It also provides LPC interface to control Super I/O functions and is connected to the network via an external Ethernet PHY module. It also communicates with onboard components via six SMBus interfaces, fan control, Platform Environment Control Interface (PECI) buses, and General Purpose I/O (T-SGPIO) ports.

The Nuvoton WPCM450 (Manufacturer P/N WPCM450RA0BX) has all the features as described above plus IPMI 2.0 support. This particular chip is installed on the X7SPT-DF-D525 motherboard model.

Note: Please refer to the Embedded IPMI User's Guide posted on our website at http://www.supermicro.com/support/manuals/. You may also find information about IPMI by visiting Intel's website at http://www.intel.com/design/servers/ipmi/

1-14


1-8 Node Hot-Swapping

The X7SPT-DF-D525 supports cable-free node hot-swapping when installed in a Supermicro 2U Twin2 Server chassis together with the cable-free hot-swap adapter (both sold separately). Node hot-swapping enables the user to replace a mother-board in a multi-node server without powering down the entire system. However, cable-free node hot-swapping allows node hot-swapping without the tedious task of unplugging and plugging back all the supporting cables between the chassis and motherboard. This is done by mounting the motherboard on a tray and attaching the tray's adapter to the motherboard. The adapter has a connector on its end that plugs into the server's backplane. This serves as the connection between the motherboard and all the components mounted in the chassis. Thus the term 'cable-free'. It also enables the motherboard to easily slide in and out of the chassis for easy maintenance. See the figure below for more information.

Cable-Free Node Hot-Swap Adapter.

An Adapter is attached to the motherboard. This connects the SATA drive, System Power, etc between the motherboard and the chassis.

Connector on the Adapter's end.

The entire module slides into the chassis and the adapter's connector engages with the socket on the chassis' back-plane.

Motherboard

The entire setup slides into chassis

Adapter TrayNote: The image is for illustration purposes only and is not the same motherboard described in the manual.

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Static-Sensitive Devices

Electrostatic-Discharge (ESD) can damage electronic com ponents. To pre-vent damage to your system board, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD.

Precautions• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing the board from the antistatic bag.

• Handle the board by its edges only; do not touch its components, peripheral chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard and peripherals back into their antistatic bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the motherboard.

• Use only the correct type of onboard CMOS battery. Do not install the onboard upside down battery to avoid possible explosion.

UnpackingThe motherboard is shipped in antistatic packaging to avoid static damage. When unpacking the board, make sure the person handling it is static protected.

2-2


MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

2-2 Motherboard Installation

All motherboards have standard mounting holes to fit different types of chassis. Make sure that the locations of all the mounting holes for both motherboard and chassis match. Although a chassis may have both plastic and metal mounting fas-teners, metal ones are highly recommended because they ground the motherboard to the chassis. Make sure that the metal standoffs click in or are screwed in tightly. Then use a screwdriver to secure the motherboard onto the motherboard tray.

Caution: Some components are very close to the mounting holes. Please take precautionary measures to prevent damage to these components when installing the motherboard to the chassis.

Tools Needed

Philips Screwdriver Pan head screws (7 pieces)

Location of Mounting HolesThere are seven (7) mounting holes on the X7SPT-DF-D525 motherboard.

Stand Offs (7 pieces)(Only if needed)

Note: The above items are not provided with this motherboard.


2-3

Installation Instructions

Caution: To avoid damaging the motherboard and its components, please do not use a force greater than 8 lb/inch on each mounting screw during motherboard installation.

Locate the mounting holes on the motherboard. Refer to the layout on the previous page for mounting hole locations.

Locate the matching mounting holes on the chassis. Install standoffs in the chassis as needed. Align the mounting holes on the motherboard against the mounting holes on the chassis.

Install the motherboard into the chassis carefully to avoid damage to moth-erboard components.

Insert a Pan head #6 screw into a mounting hole on the motherboard and its matching mounting hole on the chassis, using the Philips screwdriver.

Repeat Step 4 to insert #6 screws to all mounting holes.

12

3

Stand Off

4

56 Make sure that the motherboard is securely placed on the chassis.

2-4


MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

Installing and Removing DIMMs

2-3 System Memory

CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage.

How to Install SO DIMMsInsert the desired number of SO DIMMs into the memory slots, starting with 1. DIMM1, then DIMM2. Pay attention to the notch along the bottom of the mod-ule to prevent incorrect DIMM module installation.

Insert each DIMM module at an angle vertically and snap it into place. Repeat 2. step 1 to install DIMM2 if needed. See instructions on the next page.

Memory SupportThere are two nodes on the X7SPT-DF-D525. Each node supports up to 4GB of unbuffered Non-ECC DDR3 SODIMMs (800MHz in 2 SO DIMM slots.) Populating these DIMM slots with a pair of memory modules of the same type and same size will result in interleaved memory, which will improve memory performance.

Note: Check the Supermicro website for a list of memory modules that have been validated with the X7SPT-DF-D525 motherboard.

MH2

MH3 MH4

D17

JPW

1

JUSB1

JD1JP

C3

JPU

SB1

JWD1

JPG

1JB

MC1

JPL1

JPT1

JPL2

JDIMM2

1

JDIMM1

JI2C2

JI2C

1JO

H1

JL1

JL2

SP1

+

J2

J3

JBT1

JBAT

1

JPCI

E1

JUSB5

JUSB

4

JUSB

3

JUSB2

JLPC

80

R1050

JSM

B1

FAN

1FA

N2

JCOM2

JCOM4

JPI2

C1

JWF1

J8

JVG

A1

CD1

JPB

FAN

FAN

COM

S CL

EAR

2-3 DISABLE1-2 ENABLE

JPB:BMC ENABLE/DISABLE

CD-in

JPT1:TPM ENABLE/DISABLE1-2 ENABLE2-3 DISABLE

AUD

IO F

P

T-SG

PIO

2T-

SGPI

O1

JPI2C:PWR I2C

JSM

B1:S

MBu

s1

JPUSB1:USB WAKE UP


JWF1:DOM PWR

JD1:1-3 PWR LED4-7 SPEAKER

ON

:EN

ABL

EJI

2C2

OFF

:DIS

ABL

E

JI2C

1O

FF:D

ISA

BLE

ON

:EN

ABL

E

JL2:AUDIO FRONT PANEL SELECTON:AC'97 FRONT PANEL

OFF:HD AUDIO FRONT PANELJPG1:VGA


2-3 DISABLEJPL2:1-2 ENABLE

JPL1:1-2 ENABLE2-3 DISABLE

JL1:CHASISS INTRUSION

JF1 PWR ON RST X OH/FF NIC2 NIC1 HDD LED PWR LED X NMI

2-3 NMIJWD1:1-2 RST

JBT1

:

LAN

2

LAN

1

I-SAT

A5

I-SAT

A2

I-SAT

A4

I-SAT

A1

I-SAT

A3I-S

ATA

0

SLO

T1 P

CI-E

X4

(IN X

16 S

LOT)

SYS

CPU

KB/M

OU

SE

COM4

COM3

COM2

COM

1

SODIMM2

SODIMM1

CPU

REV:

1.00

X7SP

A-L

J6J5

J10

J11

J12

J13

J14JPF

DIMM1

DIMM2


2-5

Insert the SO DIMM module vertically at about a 45 degree angle.

To Remove: Use your thumbs to gently push the side clips near both ends away from the module. This should release it from the slot. Pull the SO DIMM module upwards.

The SO DIMM Socket

Position the SO DIMM module's bottom key so it aligns with the receptive point on the slot.

Press down until the module locks into place. The side clips will automatically secure the SO DIMM module, locking it into place.

1

2

3

4

Insert this end first

Press down until the module locks into place.

Locking clip

Locking clip

Align

2-6


MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

I/OPortLocationsandDefinitions

2-4 Back Panel I/O Ports & Switches

The I/O ports are color coded in conformance with the PC 99 specification. See the figure below for the colors and locations of the various I/O ports.

Back Panel Connectors and I/O Ports

24

71 3 5 6

8

1. USB0/USB12. IPMI LAN (OEM Option)3. LAN1 Port4. LAN2 Port5. VGA Port6. Unit ID Switch

Back Panel Connectors

9

11

12

10

Node 1

7. USB0/USB18. IPMI LAN9. LAN1 Port10. LAN2 Port11. VGA Port12. Unit ID Switch

Node 2


2-7

Internal USB2/3 (Node 1)




MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

Backpanel USB0 (Node 1)




Universal Serial Bus (USB)

For each node: 2 Universal Serial Bus ports (USB0/1) are located on the I/O backpanel. Additionally, two USB headers (USB 2/3, 4/5) are also located on the motherboard to provide front chassis access. (Cables are not included). See the tables on the right for pin definitions.

Back Panel USB 0/1,PinDefinitions

Pin# Definition Pin# Definition

1 +5V 5 +5V

2 USB_PN 6 USB_PN

3 USB_PP 7 USB_PP

4 Ground 8 Ground

Front Panel USB 2/3, USB 4/5PinDefinitions

Pin # Definition Pin # Definition

1 +5V 6 +5V

2 USB_PN 7 USB_PN

3 USB_PP 8 USB_PP

4 Ground 9 Ground

5 NA 10 Key

4

3

1

25

12


43

678

56

7

8

2-8


IPMI LAN (Node 1, Node 2)

LAN1 (Node 1, Node 2)

LAN2 (Node 1, Node 2)

LAN Ports / IPMI

For each node: There are LAN ports located on the I/O back panel. These ports accept RJ45 type cables. There are two Ethernet ports (LAN1 & LAN2) and one IPMI port for each node on the motherboard

Note: Please refer to the LED Indicator Section for LAN LED information.


RJ45/LANPinDefinitions


1 TX_D1+ 5 BI_D3-

2 TX_D1- 6 RX_D2-

3 RX_D2+ 7 BI_D4+

4 BI_D3+ 8 BI_D4-

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

61

2

43

5

6

1

2

4

3

5


2-9

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

VGA Port/Connector (Node 1)

VGA Port/Connector (Node 2)

1

VGA Connector

For each node: A VGA connector is located next to the LAN Ports on the I/O back panel. This connector is used to provide video display. Refer to the board layout below for the location.

1


15-pin VGA Connector

VGA Port/ConnectorPinDefinitions


1 Red Video 9 +5V DC

2 Green Video 10 Ground (Vsync, DDC)

3 Blue Video 11 Reserved

4 Reserved 12 I2C Data

5 Ground 13 H Sync

6 Red Return 14 V Sync

7 Green Return 15 I2C Clock

8 Blue Return

2

2

2-10


Rear UID (Unit ID) Switch

The Rear UID Switch is used together with the Front Panel UID LED and Rear UID LED (located next to the UID Switch). The Rear UID Switch makes it easier to identify or 'mark' the unit by turning on both the blue UID LED on the back panel and the UID LED on the front panel simulta-neously. It enables the user to locate the system from either side of the chassis when the system is installed for example with several units, to pinpoint which system the user wants to work on.

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

1


2

UID Switch (Node 1)

UID Switch (Node 2)

1

2


2-11

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

Serial Ports (JKCOM/JCOM) - OEM Option

Two internal serial port headers (COM1, COM2) are located on the motherboard for each node. See the table on the right for pin definitions.

Serial Ports-COM1/COM2/COM3/COM4PinDefinitions


1 DCD 6 DSR

2 RXD 7 RTS

3 TXD 8 CTS

4 DTR 9 RI

5 Ground 10 N/A

JCOM2 (Node 1)

JCOM1 (Node 1)

JKCOM2 (Node 2)

JKCOM1 (Node 2)

1

2

4

3

1 24

3

2-5 Header Connections

This section provides brief descriptions and pin-out definitions for onboard header connectors. Be sure to use the correct cable for each header or connector.

2-12


Universal Serial Bus (JUSB/JKUSB)

For each node, there are two USB head-ers located on the motherboard to provide front chassis access. (Cables are not included). See the tables on the right for pin definitions.

Front Panel USB 2/3, USB 4/5PinDefinitions


1 +5V 2 +5V

3 USB_PN 4 USB_PN

5 USB_PP 6 USB_PP

7 Ground 8 Ground

9 NA 10 Key

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

12

4 3

JKUSB2 (Node 2)

JKUSB3 (Node 2)

JUSB2 (Node 1)

JUSB3 (Node 1)

1

2

4

3


2-13

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

Front Panel Accessible Add-on Card Header (JF2)

JF2 Add-on card header provides front access to the power supply, Serial ATA and Front Panel Control connections for the motherboard. Plug an Add-On card into this header to use the functions indicated above. This header is designed specifically for this motherboard. Refer to the tables to the right for pin-out definitions.

JF21

1

2-14


3 41 2

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

Onboard Speaker (JKSP1/SP1)

An onboard speaker or buzzer is pro-vided for each node. This device pro-vides audible status messages for the motherboard.

SKP1 (Node 2)

JKTPM (Node 2)

JTPM (Node 1)

SP1 (Node 1)

1

2

4

3

TPM Header (JTPM/JKTPM)

This header is used to connect a Trusted Platform Module (TPM), available from a third-party vendor. A TPM is a secu-rity device that allows encryption and authentication of hard drives. It enables the motherboard to deny access if the TPM associated with the hard drive is not installed in the system. See the table on the right for pin definitions.

Trusted Platform Module HeaderPinDefinitions


1 LCLK 2 GND

3 LFRAME 4 No Pin

5 LRESET 6 VCC5

7 LAD3 8 LAD2

9 VCC3 10 LAD1

11 LAD0 12 GND

13 RSV0 14 RSV1

15 SB3V 16 SERIRQ

17 GND 18 CLKRUN

19 LPCPD 20 RSV2


2-15

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

SMB (JSMB1/JKSMB1)

A System Management Bus (SMB) header is located at JSMB1 for Node 1 and JKSMB1 for Node 2. Connect the appropriate cable here to use the SMB I2C connection on your system.

SMB HeaderPinDefinition

Pin# Definition

1 Data

2 Ground

3 Clock

4 No Connection

1

2

JSMB1 (Node 1)

JKSMB1 (Node 2)

JWF1 (Node 1)

JKWF1 (Node 2)

1

2

4

3

3

4

SATA DOM Power - OEM Option

The SATA DOM Power on JWF1 for Node 1 and JKWF1 for Node 2 is used to supply power to SATA Disk-on-Module (DOM) solid-state storage devices.

2-16


2-6 Jumper Settings

Explanation of Jumpers

To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board.

Note: On two pin jumpers, "Closed" means the jumper is on and "Open" means the jumper is off the pins.


2-17

LAN Port Enable/Disable (JPL/JKPL)

The JPL jumper is used to disable/enable the LAN ports on the motherboard. See the table on the right for jumper settings. The default setting is enabled.

LAN EnableJumper Settings

Pin# Definition

1-2 Enabled (default)

2-3 Disabled

B

AC

BMC Enable/Disable (JPB/JKPB)

The JPB jumper is used to enable or disable the onboard Baseboard Manage-ment Controller (BMC) and the on-board IPMI feature. This jumper is used together with the IPMI settings in the BIOS. The default position is pins 1 and 2 (enabled). See the table on the right for jumper settings.

JPB/JKPBPinDefinitions

Pin Setting Definition

Pins 1-2 Enabled (Default)

Pins 2-3 Disabled

A LAN2 Enable/Disable (Node 1)LAN2 Enable/Disable (Node 2)

LAN1 Enable/Disable (Node 1)

LAN2 Enable/Disable (Node 2)

BMC Enable/Disable (Node 1)

BMC Enable/Disable (Node 2)

BM

H8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

D

CD

E

F

EF

2-18


CMOS Clear (JBT1/JKBT1)

JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads to prevent accidental clearing of the CMOS. To clear the CMOS, use a metal object such as a small screwdriver to touch both pads at the same time to short the connection. Always remove the AC power cord from the system before clearing CMOS.

Important: You must completely shut down the system, remove the AC power cord and then short JBT1 to clear CMOS.

A

CMOS Clear (Node 2)

Watch Dog Timer (Node 1)

Watch Dog Timer (Node 2)

CMOS Clear (Node 1)

MH2

MH3

MH4

D17

JPW1

JUSB

1

JD1

JPC3

JPUSB1

JWD

1

JPG1 JBMC1JPL1

JPT1

JPL2

JDIM

M2

1

JDIM

M1

JI2C2

JI2C1JOH1JL1

JL2

SP1+

J2

J3

JBT1

JBAT1

JPCIE1

JUSB

5

JUSB4

JUSB3JUSB

2

JLPC80

R105

0

JSMB1

FAN1 FAN2

JCO

M2

JCO

M4

JPI2C1

JWF1

J8

JVGA1

CD1

JPB

FAN

FAN

COMS CLEAR

2-3

DIS

ABLE

1-2

ENAB

LEJP

B:BM

C EN

ABLE

/DIS

ABLE

CD-in

JPT1

:TPM

ENA

BLE/

DIS

ABLE

1-2

ENAB

LE2-

3 D

ISAB

LE

AUDIO FP

T-SGPIO2 T-SGPIO1

JPI2

C:PW

R I2

C

JSMB1:SMBus1

JPUS

B1:U

SB W

AKE

UP

2-3

DIS

ABLE

1-2

ENAB

LE

JWF1

:DO

M P

WR

JD1:

1-3

PWR

LED

4-7

SPEA

KER

ON:ENABLEJI2C2OFF:DISABLE

JI2C1OFF:DISABLEON:ENABLE

JL2:

AUD

IO F

RONT

PAN

EL S

ELEC

TO

N:AC

'97

FRO

NT P

ANEL

OFF

:HD

AUD

IO F

RONT

PAN

ELJP

G1:V

GA

2-3

DIS

ABLE

1-2

ENAB

LE2-

3 D

ISAB

LEJP

L2:1

-2 E

NABL

E

JPL1

:1-2

ENA

BLE

2-3

DIS

ABLE

JL1:

CHAS

ISS

INTR

USIO

N

JF1

PWR

ON

RST

X O

H/FF

NIC

2 NI

C1 H

DD

LED

PW

R LE

D X

NM

I

2-3

NMI

JWD

1:1-

2 RS

T

JBT1:

LAN2

LAN1

I-SATA5

I-SATA2

I-SATA4

I-SATA1

I-SATA3

I-SATA0

SLOT1 PCI-E X4 (IN X16 SLOT)

SYS

CPUKB/MOUSE

COM

4

COM

3

COM

2

COM1

SODI

MM

2

SODI

MM

1

CPU

REV:1.00X7SPA-L

J6J5

J10 J11

J12

J13

J14

JPF

Metal contact pads

Motherboard

B

A

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

C D

Watch Dog Timer Enable/Disable (JWD1/JKWD1)

The Watch Dog Timer (JWD) is a system monitor that can reboot the system when a software application hangs. Short pins 1~2 to reset the system if an application hangs. Short pins 2~3 to generate a non-maskable interrupt (NMI) signal for the application that hangs. See the table on the right for jumper settings. Watch Dog must also be enabled in the BIOS.

Watch Dog Jumper Settings (JWD)

Jumper Setting Definition

Pins 1-2 Reset (default)

Pins 2-3 NMI

Open Disabled

BCD


2-19

LAN Port LEDs

Four total LAN ports are located on the I/O Backpanel. Each Ethernet LAN port has two LEDs. The yellow Activity LED (right, see below) indicates activity, while the Link/Speed LED (left) may be green, amber or off to indicate the speed of the connection. See the tables at right for more information.

2-7 Onboard Indicators

Rear View (when facing the rear side of the chassis)

Activity LEDLink/Speed LED


GLAN Activity LED Indicator

Color Definition

Yellow (Flashing) ConnectionActive

GLAN Link/Speed LED Indicator

LED Color Definition

Off No Connection or 10 Mbps

Green (On) 100 Mbps

Amber (On) 1 Gbps

2-20


E

Unit ID LEDs (LE2/LKE2)

There are two unit ID LEDs on the motherboard, one for each node. Each Unit ID LED is associated with a Unit ID switch. The Unit ID Switch activates the Unit ID LED next to it, and the corresponding Unit ID LED on the front panel of the chassis (if so equipped). This enables a user or a service person to easily identify which unit is being serviced from behind or in front of the system, a mounting rack or cabinet by simply looking at what chassis has its Unit ID LED activated.

MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

A

B

A Unit ID (Node 1)Unit ID (Node 2)

Main Power LED (Node 1)

Main Power LED (Node 2)

Power/Suspend LED (Node 1)

Power/Suspend LED (node 2)

BCD

F

Main Power LED (LE1/LKE1)

There are two main power LEDs on the motherboard, one for each node. This LED indicates that power from the power supply is reaching the motherboard (hard switched, usually on the power supply).

Power/Suspend LED (DP2/DKP2)

There are two Power/Suspend LEDs on the motherboard, one for each node. This LED indicates that the system is turned on (soft switched). When this LED is blink-ing, it indicates that the system is on suspend mode.

E

C

DF


2-21

SATA LED (Node 2)

SATA LED (Node 1)

BMC Heartbeat LED (Node 2)

BMC Heartbeat LED (Node 1)M

H8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

A

B

ABCD

SATA LED (DKP3/DP3)

There are two SATA LEDs on the motherboard, one for each node. When this LED is blinking, it indicates activity on the system's SATA port(s).

C

D

BMC Heartbeat LED (DKP1/DP1)

There are two BMC Heartbeat LEDs on the motherboard, one for each node. When this LED is blinking, it indicates that the Baseboard Management Controller (BMC) is activated.

2-22


MH

8

MH

7M

H6

MH

5

MH

3

MH

2

MH

1

JKWF1

JWF1

1 3

IKSATA1

ISATA1

BKT1

BT1

LKE2

AC

LE2

AC

SKW1

SW1

UK67

J666

JKLAN1

JLAN1

JF2

JKTPM

1920

JTPM

12

1920

JKD

IMM

1

JDIM

M1

JKD

IMM

2

JDIM

M2

E

JKPL

2

JKPL1

JKWD1

JKPB

JWD1

JPB

3

JPL1

JPL2

1

U39

DKP3DKP2

DKP1

A C

LKE1

AC

LE1

DP2

SKP1 +

SP1

+

JKBT1

JBT1

JKUSB2 JKUSB3

JUSB31 7 JUSB21 7

JKSMB1

JSM

B1

JKCOM1

JKCO

M2

JCO

M1

JCO

M2

5

JVGA1

DP1

2-8 Serial ATA Ports

A

SATA Connectors

There are 4 SATA ports supported on each node. IKSATA1/ISATA1 are located on the motherboard, while the rest are supported through the hot-plug using an adapter card (see JF2, 2-13). These four SATA ports are supported by the Intel ICH9R South Bridge. See the table on the right for pin definitions.

SATA Connectors PinDefinitions

Pin# Signal

1 Ground

2 SATA_TXP

3 SATA_TXN

4 Ground

5 SATA_RXN

6 SATA_RXP

7 Ground

B

IKSATA1 (Node 2)

ISATA1 (Node 1)AB

3-1

Chapter 3: Troubleshooting

Chapter 3

Troubleshooting

3-1 Troubleshooting Procedures

Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter. Always disconnect the AC power cord before adding, changing or installing any hardware components.

Before Power On1. Be sure to unplug the power cable before installing or removing the compo-

nents.)

2. Make sure that there are no short circuits between the motherboard and chas-sis.

3. Disconnect all ribbon/wire cables from the motherboard, including those for the keyboard and mouse. Also, be sure to remove all add-on cards.

4. Connect the chassis speaker and the power LED to the motherboard. Check all jumper settings as well.

No Power1. Make sure that there are no short circuits between the motherboard and chas-

sis.

2. Make sure that all jumpers are set to their default positions.

3. Check if the 115V/230V switch on the power supply is properly set.

4. Turn the power switch on and off to test the system.

5. The battery on your motherboard may be old. Check to make sure that it still supplies ~3VDC. If it does not, replace it with a new one.

No Video1. If the power is on, but you have no video--in this case, you will need to remove

all the add-on cards and cables first.

3-2

X7SPT-DF-D525 User's Manual

2. Use the speaker to determine if any beep codes exist. (Refer to Appendix A for details on beep codes.)

3. Remove all memory modules and turn on the system. (If the alarm is on, check the specs of memory modules, reset the memory or try a different one.)

Memory Errors 1. Make sure that the SO-DIMM modules are properly installed and fully seated

in the slots.

2. You should be using unbuffered 800MHz Non-ECC DDR3 SO DIMM memory for the X7SPT-DF-D525 (See Section 2-3). Also, it is recommended that you use the memory modules of the same type and speed for all DIMMs in the system.

3. Check for bad DIMM modules or slots by swapping modules between slots to see if you can locate the faulty modules.

4. Check the power supply voltage 115V/230V switch.

LosingtheSystem’sSetupConfiguration1. Please be sure to use a high quality power supply. A poor quality power supply

may cause the system to lose the CMOS setup information. Refer to Section 1-5 for details on recommended power supplies.

2. The battery on your motherboard may be old. Check to verify that it still supplies ~3VDC. If it does not, replace it with a new one.

3. If the above steps do not fix the Setup Configuration problem, contact your vendor for repairs.

3-2 Technical Support Procedures

Before contacting Technical Support, please make sure that you have followed all the steps listed below. Also, Note that as a motherboard manufacturer, Supermicro does not sell directly to end users, so it is best to first check with your distributor or reseller for troubleshooting services. They should know of any possible problem(s) with the specific system configuration that was sold to you.

1. Please go through the ‘Troubleshooting Procedures’ and 'Frequently Asked Question' (FAQ) sections in this chapter or see the FAQs on our website (http://www.supermicro.com/support/faqs/) before contacting Technical Support.

2. BIOS upgrades can be downloaded from our website at (http://www.supermicro.

3-3

Chapter 3: Troubleshooting

com/support/bios/).

Note: Not all BIOS can be flashed. Some cannot be flashed; it depends on the modifications to the boot block code.

3. If you've followed the instructions above to troubleshoot your system, and

still cannot resolve the problem, then contact Supermicro's technical support and

provide them with the following information:

• Motherboard model and PCB revision number

• BIOS release date/version (this can be seen on the initial display when your

system first boots up)

•System configuration

An example of a Technical Support form is on our website at (http://www.

supermicro.com/support/contact.cfm).

4. Distributors: For immediate assistance, please have your account number ready

when placing a call to our technical support department. We can be reached

by e-mail at [email protected], by phone at: (408) 503-8000, option

2, or by fax at (408)503-8019.

3-3 Frequently Asked Questions

Question: What type of memory does my motherboard support?

Answer: Each node of the X7SPT-DF-D525 supports up to 4GB of unbuffered 800MHz Non-ECC DDR3 SO DIMMs in 2 sockets (1.5V, 512MB, 1GB, 2GB)

Question: Why does Microsoft Windows XP (SP2) and Windows Vista show less memory than what is physically installed?

Answer: Microsoft implemented a design change in Windows XP with Service Pack 2 (SP2) and Windows Vista. This change is specific to the Physical Ad-dress Extension (PAE) mode behavior which improves driver compatibility. For more information, please read the following article at Microsoft’s Knowledge Base website at: http://support.microsoft.com/kb/888137.

Question: How do I update my BIOS?

Answer: It is recommended that you do not upgrade your BIOS if you are not experiencing any problems with your system. Updated BIOS files are located on our web site at http://www.supermicro.com/support/bios/. Please check our

3-4

X7SPT-DF-D525 User's Manual

BIOS warning message and the information on how to update your BIOS on our web site. Select your motherboard model and download the BIOS (.rom) file to your computer. Also, check the current BIOS revision and make sure that it is newer than your BIOS before downloading. You may choose the zip file or the .exe file. If you choose the zipped BIOS file, please unzip the BIOS file onto a bootable device or a USB pen/thumb drive. To flash the BIOS, run the batch file named "ami.bat" with the new BIOS ROM file from your bootable device or USB pen/thumb drive. Use the following format:

F:\> ami.bat BIOS-ROM-filename.xxx

Notes: Always use the file named “ami.bat” to update the BIOS and insert a space between "ami.bat" and the filename. The BIOS-ROM-filename will bear the motherboard name (i.e., X7SPT) and build version as the extension. For example, "X7SPT0.526".

When completed, your system will automatically reboot. If you choose the .exe file, please run the .exe file under Windows to create the BIOS flash floppy disk. Insert the floppy disk into the system you wish to flash the BIOS. Then, boot the system to the floppy disk. The BIOS utility will automatically flash the BIOS without any prompts. Please note that this process may take a few minutes to complete. Do not be concerned if the screen is paused for a few minutes.

Warning: Do not shut down or reset the system while updating the BIOS to prevent possible system boot failure!

When the BIOS flashing screen is completed, the system will reboot and will show “Press F1 or F2”. At this point, you will need to load the BIOS defaults. Press to go to the BIOS setup screen, and press to load the default settings. Next, press to save and exit. The system will then reboot.

Note: The SPI BIOS c

Documents

MNL-X7SPT-DF-D525 - ICH9 - Motherboard - Super Micro … · 2016. 7. 1. · Manual Revision 1.0 Release Date: February 22, 2011 Unless you request and receive written permission from