TABLE LEG LONG&SHORT FRAME

~ / %mmX170 BOLT 41 L(ANGIE IRON 145X45) 4

~ ~ %mmX28mmx3mm(WASHER) 41 .·

' %mmXYiX90 BOLT 8 @j SEMl-TUBULAR RIVET 4 17X34X3/8-16UNC

y %mmX50BOLT 4 -s %MMX114mm BLOT 81 0 318 mmX28mmx3mm(WASHER) 20 @ 13 mmX32mmx3mm(V'JASHER) 31

0 %mmXT7.7 NUT 8 <?P> SEMl-TUBULAR RIVET 8 17*52*3/8-16UNC

TOP RAIL SLATE

~ 3/8X63mmBOL T 18 < lllllllllllllllllllllllllllllllllll/JI! 11 6llE70FA FLAT HEAD PHILLIPS SCREW 16

@> %x28 mmx3mm(WASHER) 1_8 <? 100MMX25MMX8MM WOOD 16

APRON APRON(SIDE) 1

l 3/8X50mmBDLT 12 A 1/4llE16mmbolt 8

sl %x28 mmx3mm(WASHER) 12

e M6•2.0(WASHER)

0 ~ L(ANGIE IRON 116X30) 4 LEG&LEG CONNECTION

~ 3q 3.8•12TA FLAT HEAD PHILLIPS SCREW

~ 3/8X63mmBDL T 4 FAIRWAY

0 %x28 mmx3mm(WASHER) 4 < lll11111111lllllA1 l 8#l1El' FA FLAT HEAD PHILLIPS SCREW 30 1

® END TOP RAIL 2

® SIDE TOP RAIL 4

® LONG BASE APRON 2

@ SHORT BASE APRON 2

CORNERX4 drop pocketX6 LX4pcs MX2pcs MIDDLE HOLEX2 TABLE LGEX4

drop pocket install corner

corner crimping

~ 1-fommX33mmBOL T 12

~ %x28 mmx3mm(WASHER) 12

packet screw .,,A 1/ 4l1El0 mmbolt 12 0 114xl5 mmx1 mm(WASHER) 12

© LONG SUPPORT FRAME 2

© SHORT SUPPORT FRAME 2

® MIDDLE SUPPORT FRAME 2

C8) SLATE 3~PCS

CD TABLE LEG 1 2

STEP 1

~ tJ ~

II=================;:===~\

' 1

1 1

ß 3/8X5 0 mmBOU T 1

%x28 mmx3mm(WASHER)

LEG&LEG CONNECTION

1

STEP2

.·

REMARK:

Sphericnl segr-ient of the first spher ico.l segr-ient in the foot blocl-<s ho.ve nlreo.oly loeen loool-<ing olepnrtr-ien t in genern l .

the structure of sphericnl seg r-i ent in the nsser-ilo l y of n certo. in lnw: there is n certo. in syr-ir-ietry

sphericnl segr-ient) so nsser-iloly screws nre the snr-ie .

STEP 3

--

TABLE LEG

/ LONG&SHORT FRA E

this is slate

:

STEP4

.0 ioo...,.,x20...,.,xa,.,,., wooo

RE MARK: The first spherical segment of the chassis should first be completed. Second stone an the bottom shelf then settle.and use rapid tooth screws.

At last ,wood chips for horizontal adjustment

STEP5

SIDE TOP RAIL PLAN

END TOP RAIL PLAN

RE MARK: In the lock by connec t ing screws deck o.nd s lo. te) the

bo.ll Must first puMp in the ston e on the to.blec loth) o.nä

we rely on hiM to wro.p c loth.

STEP 6

0

%x28 mmx3mm(WASHER)

\ ~fommX33MM BOL T

~,,.A 1/4• 10mmboH 0 v«Sm~'•m(W""'RJ

corner crimping

STEP 7

~

\ APRON(SIDE) „ ~ A l/4916MMboll

RE MARK:

Long shie ld connec tion with the r e lo. ti o n s h ip

between short-sheet ing

STEP8 They o.re the two holes

. \

0 3/8X50MMBDL T

l %x28 mmx3mm(WASHER)

APRON