17
Apex systems International DMM13001-B Product Specification Copyright Apex Systems International BVBA www.apexsyst.com 27/5/2014 Page 1 of 17 [email protected] Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W 1.0 General The DMM13001 module is a dimmer with 4 channels of maximum 100Watts. If the load exceeds 100W, the 4 channels can be combined according to the needs : 1x100W + 1x300W, 2 x 200W or 1x400W. The module is designed for DIN rail mounting and is 6U wide (105mm). The DMM13001 module is suitable for switching and controlling dimmable electronic control gear for fluorescent lighting, compact fluorescent lighting or dimmable LED lighting. The dimmer has a thermal protection and a short circuit protection. The dimmer can be controlled in several ways : a) by push buttons connected to the dimmer inputs. b) by analog inputs (0..10V) c) by push buttons connected to the bus d) by an easyplus home server connected to the bus. BUS Control : The dimmer module is controlled via the Easyplus CAN-bus. Commands coming from an Easyplus server or an Easyplus input device are controlling the dimmer outputs. The dimmer value and ramp speed are varied through the bus system. Analog input control (0..10V): The dimmer module is controlled by a 0-10V input signal. A voltage between 0 and 10 volts is applied to the input connector and according to the input, the output 230V AC follows. Push button control : The dimmer is controlled by buttons. You can connect 4 buttons to control the 4 dimmer outputs. The last value of the output is stored in the ram memory. 2.0 Loads The DMM13001-B is fit for light bulbs, halogen lamps (230VAC), dimmable retrofit ledlamps and electronic transformers. ** Remark : there is another type of the 4 channel dimmer : type DMM13001-M/I to control motors and inductors. light bulb halogen lamp (230V) dimmable retrofit ledlamps electronic transformer motor electric transformer

Micro Controlled Dimmer 13001 - Apex Syst · 2014. 5. 26. · been cooled. After cooling, it restar ts automatic. In the software ther e is a button “get overheat protection value”

  • Upload
    others

  • View
    1

  • Download
    0

Embed Size (px)

Citation preview

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    1.0 GeneralThe DMM13001 module is a dimmer with 4 channels of maximum 100Watts. If the load exceeds 100W, the 4 channels can be combined according to the needs : 1x100W + 1x300W, 2 x 200W or 1x400W.The module is designed for DIN rail mounting and is 6U wide (105mm). The DMM13001 module is suitable for switching and controlling dimmable electronic control gear for fluorescent lighting, compact fluorescent lighting or dimmable LED lighting.

    The dimmer has a thermal protection and a short circuit protection.

    The dimmer can be controlled in several ways :a) by push buttons connected to the dimmer inputs.b) by analog inputs (0..10V)c) by push buttons connected to the busd) by an easyplus home server connected to the bus.

    BUS Control : The dimmer module is controlled via the Easyplus CAN-bus. Commands coming from an Easyplus server or an Easyplus input device are controlling the dimmer outputs. The dimmer value and ramp speed are varied through the bus system.

    Analog input control (0..10V): The dimmer module is controlled by a 0-10V input signal. A voltage between 0 and 10 volts is applied to the input connector and according to the input, the output 230V AC follows.

    Push button control : The dimmer is controlled by buttons. You can connect 4 buttons to control the 4 dimmer outputs. The last value of the output is stored in the ram memory.

    2.0 LoadsThe DMM13001-B is fit for light bulbs, halogen lamps (230VAC), dimmable retrofit ledlamps and electronic transformers.

    ** Remark : there is another type of the 4 channel dimmer : type DMM13001-M/I to control motors and inductors.

    light bulb halogen lamp (230V) dimmable retrofit ledlamps electronic transformer

    motor electric transformer

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 1 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    3.0 MountingThe module fits on a standard DIN Rail and needs no special tools to install it.

    4.0 Power Connections

    4.1 General

    The electrical connection is made with the standard bus connector and the big power connector on top of the dim-mer. The module is powered with 24V DC via the bus connector. You can also add power only without connecting the bus system. The 10 pole power connector is supplied by 230VAC.

    Side View

    Front View Backside

    230 VAC Supply + 4 dimmer channels

    +24V, GND, Bus H, Bus L

    4 direct inputs for buttons OR 4 analog inputs 0..10V

    Before applying any power, be sure that all signals are correctly wired !!!

    Address programming button

    Led powerLed programming

    Jumper J3 for input selection(remove cover first)

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 2 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    4.2 Power Connections 24VDC - 230VAC - example 1

    The 24VDC is attached to the busconnector and the 230VAC is connected to the green power connector. All of the neutral wires of the loads are connected to the power connector.

    4.3 Power Connections 24VDC - 230VAC - example 2

    The 24VDC is attached to the busconnector and the 230VAC is connected to the green power connector. Only one of the neutral wires is connected to the green power connector to provide power to the module. The neutral wires of the loads are connected to the automatic fuse directly.

    Power supply Dimmer Automatic fuse

    Neutral wiresnot connectedto the greenpower connector.

    Power supply Dimmer Automatic fuse

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 3 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    5.0 Dimmer Control Modes

    5.1 Dimmer Control by 4 buttons on the direct inputs.

    The 4 dimmer channels are controlled by 4 buttons which are connected to the 4 digital inputs on the dimmer itself. The dimmer channels are then controlled with a dimmer function. Short push a button to light the light source to the last “on” light level, press short again to switch the light off. Long press to increase the light level, short release and long press again to decrease the light level.

    5.1.1 Jumper setting A jumper must be placed on the pins J3.

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 4 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    5.2 Dimmer Control by analog inputs 0..10V

    The 4 dimmer channels are now controlled by an external 0..10V signal. The signal can be generated by a potenti-ometer or by a home automation system.

    Remark : If you use 0..10V analog signals to control the dimmer channels, the dimmer cannot be controlled by an Easyplus home server. 5.2.1 Jumper setting

    The jumper on J3 must be removed.

    5.3 Dimmer Control by external buttons

    The 4 dimmer channels are controlled by 4 buttons which are connected to the bus system of the dimmer. The input address will control the channel of the dimmer with the same address. For example : the dimmer pro-grammed base address is 24, so dimmer channel 0 = address 24, dimmer channel 1 = address 25, dimmer channel 2 = address 26 and dimmer channel 3 = address 27. If we push on a digital input with address 24 we will control the dimmer channel 0. Using input 27 will control channel 3.

    Power supply

    Home automation system X

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 5 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    5.3.1 Jumper setting A jumper must be placed on the pins J3.

    5.4 Dimmer Control by Easyplus Home Server

    The dimmer will be controlled by the Easyplus home server through the bus system. The dimmer behavior is then programmed with the Easylink software. For more information can be found in the Easylink software help.

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 6 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    Remark : if the dimmer channels are controlled by an Easyplus home server, the analog inputs on the dimmer can-not be used.5.4.1 Jumper setting

    The jumper on J3 must be removed.

    5.5 Dimmer control in Pre home automation system

    The dimmer is controlled by digital inputs from bus system or/and is controlled by the direct inputs on the dimmer module. In this mode, all of the dimmer channels will be switched off by an external long push on digital input 0.

    5.5.1 Jumper setting A jumper must be placed on the pins J3.

    6.0 Higher output power by output paralleling.Every channel can handle a load up to 100W. It is possible to combine several outputs to be able to have one output of 200, 300 or 400W. Setting up the dimmer to combine several outputs is done in the Easyplus dimmer control software, which can be freely downloaded for the website. To use the software, you will need the Easyplus USB-Bus interface. Order code : USB14011

    6.1 Power output combinations

    6.1.1 Two channels of 200Watts

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 7 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    6.1.2 One channel of 300Watts / one channel of 100Watts

    6.1.3 One channel of 400Watts

    Software configuration for 2x200Watts

    Software configuration for 1x300Watts / 1 x100Watts

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 8 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    6.2 Programming hardware

    To change the configuration of the 4 channel dimmer, there is an Easyplus dimmer configuration tool. The tool can be downloaded from the website, www.apexsyst.com. The program makes use of the USB14001_USB_BUS interface. Just connect the interface to the usb plug of the pc on one side and to the bus system on the other side.

    ** In many cases, the configuration of the dimmer doesn’t need any changes.

    6.3 Description of the software tool

    6.3.1 General descriptionThe dimmer configuration software is used to test and to fine tune your dimmer channels. You can set the minium level and the profile of each channel. You can also change the base address and check the over-heat protection value. ** check out the drawing on the next page.

    6.3.2 Base Address ProgrammingIf used in a bus system every dimmer needs to get a different base address. You can change it by selecting the module base address spin button and then press the button “Program Base Address”. Then press the small button on the module itself (see below). A led starts blinking and the confirmation is received in the program. In the left under corner a small message appears for a small time period.

    Software configuration for 1x400Watts

    Hardware configuration for programming

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 9 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    6.3.3 Testing / Minium level settings To test every channel, select the module base address and then move the sliders form each channel. Check out where the minimum light level is and then press the button “Set Minimum Level Ch1(..4)” to set the minimum level. Now the light level on that channel will start from the stored light value.

    Base address programming Address Program button

    Led lights up in programming mode.Led blinks after pressing the button, indicating that an address has beenprogrammed.

    Software configuration tool

    Press to program address

    Select funtionPush to set minimum

    Pust to get overheat value

    Connection status Busdata

    Test slider

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 10 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    6.3.4 Combining ChannelsTo be able to connect loads up to 400Watts it is possible to combine several output channels. Select sev-eral output check boxes under one input control. This input will then control the selected output channels at the same time. You also need to connect the output channels on the hardware site. Check out higher in the document.

    6.3.5 Select ProfileThe output behavior of every channel can be changed by selecting another profile according to the kind of load. Every output channel can have it’s own output profile.

    6.3.6 Overheat protectionThe module has an overheating protection. If a channel gets to hot, the module shuts down until it has been cooled. After cooling, it restarts automatic. In the software there is a button “get overheat protection value” to be able to read the heat value on this moment. In this way it is also easy to determine if the mod-ule is to loaded or not.

    Hardware configuration for programming

    Store the configurationinto the dimmer module.Read the configuration

    from the dimmer module.Put the checkboxes back into the default position.

    Select the checkboxes according to your needs.

    Select a profile and press the “sent profile” button to store into the dimmer module.

    Put the profile in the default position.

    Read the profilefrom the dimmer module.

    Store the profileinto the dimmer module.

    Select a profile.

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 11 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    7.0 Example UsageHere are some examples of hardware setup.

    7.1 Usage with T28 touchscreen

    Connect the T28 screen to the dimmer via the bus system. Jumper J3 must be placed on the DMM13001. The addresses must correspond. For example the dimmer has basic address 24. The push buttons on the T28 must have the address 24..27.If you press button 24, output 0 of the dimmer will be controlled. If you press button 25, output 1...*Remark : a power supply is required.

    7.2 Usage with GT28 glass touch control panel

    Connect the GT28 screen to the dimmer via the bus system. Jumper J3 must be placed on the DMM13001. The addresses must correspond. For example if the dimmer has basic address 24, he basic address of the GT28 must have the address 24.If you press button 24, output 0 of the dimmer will be controlled. If you press button 25, output 1...*Remark : a power supply is required.

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 12 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    7.3 Usage with quad input module

    Connect the DLQ03011 module to the dimmer via the bus system. Jumper J3 must be placed on the DMM13001. The addresses must correspond. For example if the dimmer has basic address 24, he basic address of the DLQ03011 must have the address 24.If you press button 24, output 0 of the dimmer will be controlled. If you press button 25, output 1...

    *Remark : a power supply is required.

    7.4 Wiring example : multiple dimmers with T28

    Connect the T28 screen to the dimmers via the bus system. Jumper J3 must be placed on every DMM13001. The addresses must correspond. For example the dimmer has basic address 24. The push buttons on the T28 must have the address 24..27. To control the next dimmer (address 28), the push buttons must have address 28..31.If you press button 28, output 0 of the dimmer with address 28 will be controlled. If you press button 25, output 1 of dimmer 24 will be controlled.*Remark : a power supply is required.

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 13 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    7.5 Cabling example : multiple dimmers with multiple quad input modules

    Connect the quad input modules to the dimmers via the bus system. Jumper J3 must be placed on every DMM13001. The addresses must correspond. For example the dimmer has basic address 24. The push buttons on the T28 must have the address 24..27. To control the next dimmer (address 28), the push buttons must have address 28..31.If you press button 28, output 0 of the dimmer with address 28 will be controlled. If you press button 25, output 1 of dimmer 24 will be controlled.*Remark : a power supply is required.

    7.6 Cabling example : multiple dimmers with a 16 input module

    Connect the 16 input module to the dimmers via the bus system. Jumper J3 must be placed on every DMM13001. The addresses must correspond. For example the digital input module has basic address 0. The dimmer modules must have the basic address 0, 4, 8 and 12. Push button 0 will control dimmer basic address 0 channel 0, push but-ton 15 will control dimmer with ba 12 channel 3.*Remark : a power supply is required.

    8.0 Bus terminator When using the DMM13001 module in a bus system, be sure that there are two bus terminators placed in the bus system. If the module is on the end of the cable please put a jumper on the bus terminator jumper pins. Two bus terminators must be used for the proper working of the bus system. Don’t put 3 or more terminators in a single bus.

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 14 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    How can we know if the bus is terminated properly ? We can measure the resistance between the CanH and the CanL. If the resistance is about 70 or 80 ohms, depending on the kind and the length of the wires, it is ok. If we measure 120 a 140 ohm, then there is only one bus terminator installed and another one should be placed.

    Consult the Easyplus technical manual for details on how the bus works and how it should be properly terminated.

    9.0 Safety instructionsRead the complete manual before carrying out the installation and activating the system.

    • The device must be mounted and commissioned by an authorised electrician in accordance with the country-specific regulations.

    • This device is exclusively suitable for DIN-rail mounting EN 50022. It must be mounted in a closed distribution board and should be well ventilated. Heat dissipation must be ensured.

    • Before carrying out the installation the DMM13001 should be de-energized.

    • The device must not be opened. The guarantee will be void if the device has been opened.

    • Electrical shock when live parts are touched.

    • This user manual has to be handed over to the user. It has to be included in the electrical installation file and has to be passed on to any new owners. Additional copies are available on the Apex systems website or via the support service.

    In case of questions, you can consult the Apex systems support service.

    Apex Systems International BVBAHermesstraat 6c1930 [email protected]

    In case of a defect, you can return your product to a registered Apex systems wholesaler, together with a clear description of your complaint (Conditions of use, stated defect…).

    BUS H

    BUS L

    Bus terminator Bus terminator2 bus terminators in one bus

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 15 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    10.0 Order Codes

    10.1 Main Module

    Order Code Description

    DMM13001-B Easyplus microcontrolled 4 channel dimmer, 4x100W/2x200W/1x100W+1x300W

    10.2 Accessories

    Description Order Code

    Power Supply 24V/240W PSU07091Power Supply 24V/60W PSU24060Multifunctional touchscreen 2.8 inch T28Glass touch panel 2.8 inch GT28Quad digital input module DLQ0403116 digital input module DIS03101Easyplus home server light EPC10008Easyplus home server medium EPC10024Easyplus home server standard EPC10040Easyplus home server exclusive EPC07101

    11.0 Guarantee Provisions- Period of guarantee: 2 years from date of delivery. The delivery date is the invoice date of purchase of the product by the consumer. If there is no invoice, the date of production applies.

    - The consumer is obliged to inform Apex systems international in writing about the defect, within two months after stating the defect.

    - In case of a failure to conform, the consumer has the right to a repair or replacement (decided by Apex systems international) free of charge.

    - Apex systems international cannot be held liable for a defect or damage as a result of an incorrect installation, improper or careless use or wrong usage or transformation of the goods.

    - The compulsory regulations of the national legislation concerning the sales of consumer goods and the protection of the consumers in the countries where Apex systems sells, directly or via sister or daughter companies, chain stores, distributors, agents or permanent sales representatives, take priority over the rules and regulations mentioned above.

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 16 of 17 [email protected]

  • Apex systems International

    DMM13001-B

    Product Specification

    Micro Controlled Dimmer 4x100W/2x200W/1x300W+1x100W

    12.0 Disclaimers

    Limited warranty and liabilityInformation in this document is believed to be accurate and reliable. However, Apex Systems International does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information.In no event shall Apex Systems International be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory.Notwithstanding any damages that customer might incur for any reason whatsoever, Apex Systems International aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Apex Systems International.

    Right to make changesApex Systems International reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof.

    Suitability for useApex Systems International products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Apex Systems International product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Apex Systems International accepts no liability for inclusion and/or use of Apex Systems International products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk.

    ApplicationsApplications that are described herein for any of these products are for illustrative purposes only. Apex Systems International makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification.Customers are responsible for the design and operation of their applications and products using Apex Systems International products, and Apex Systems International accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Apex Systems International product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s).Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Apex Systems International does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Apex Systems International products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Apex Systems International does not accept any liability in this respect.

    Copyright Apex Systems International BVBA www.apexsyst.com27/5/2014 Page 17 of 17 [email protected]

    1.0 General2.0 Loads3.0 Mounting4.0 Power Connections4.1 General4.2 Power Connections 24VDC - 230VAC - example 14.3 Power Connections 24VDC - 230VAC - example 2

    5.0 Dimmer Control Modes5.1 Dimmer Control by 4 buttons on the direct inputs.5.2 Dimmer Control by analog inputs 0..10V5.3 Dimmer Control by external buttons5.4 Dimmer Control by Easyplus Home Server5.5 Dimmer control in Pre home automation system

    6.0 Higher output power by output paralleling.6.1 Power output combinations6.2 Programming hardware6.3 Description of the software tool

    7.0 Example Usage7.1 Usage with T28 touchscreen7.2 Usage with GT28 glass touch control panel7.3 Usage with quad input module7.4 Wiring example : multiple dimmers with T287.5 Cabling example : multiple dimmers with multiple quad input modules7.6 Cabling example : multiple dimmers with a 16 input module

    8.0 Bus terminator9.0 Safety instructions10.0 Order Codes10.1 Main Module10.2 Accessories

    11.0 Guarantee Provisions12.0 Disclaimers