metecnospan®

Technical Drawings v3 - Current 05/02/2020Leaders in Thermal & Architectural Building Solutions

2 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Contents

Panel Details - PIR-R-01-6 .................................................................. 3

Typical Section Through Building - PIR13-OP02-0 ............................... 4

Barge Capping Detail - PIR13-BC01-1 ................................................ 5

Barge / Parapet Detail - PIR13-BC02-1 ............................................... 6

Head Flashing Detail - PIR13-HF01-2 ................................................. 7

Un-insulated Box Gutter Detail- PIR13-RD02-3 ................................... 8

Ridge Detail - PIR13-RD03-3 .............................................................. 9

Cyclonic / Non-cyclonic Fastening - PIR13-RD04-4 ........................... 10

Insulated Box Gutter Detail - PIR13-RD07-1 ...................................... 11

Expansion Step Detail - PIR13-RJ01-4 .............................................. 12

Roof End Lap Detail - PIR13-SL01-3 ................................................. 13

Insulated Valley Boxed Gutter - PIR13-RV01-1 .................................. 14

Eaves Gutter Detail - PIR13-WC03-2 ................................................. 15

Eaves Gutter Detail 2 - PIR13-WC04-2 .............................................. 16

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

3MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Panel Details - PIR-R-01-6

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

4 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Typical Section Through Building - PIR13-OP02-0

Roofing

g py g p p yLimited trading as Bondor. It is subject to their recalmay not be reproduced or its contents divulged withowritten authority.

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

5MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Barge Capping Detail - PIR13-BC01-1

Roofing / Cladding

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

6 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Barge / Parapet Detail - PIR13-BC02-1

Roofing / Cladding

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

7MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Head Flashing Detail - PIR13-HF01-2

Roofing / Cladding

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

8 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Un-insulated Box Gutter Detail- PIR13-RD02-3

Roofing

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

9MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Ridge Detail - PIR13-RD03-3

Roofing

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

10 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/03/2020

Standard Constructionmetecnospan®

Cyclonic / Non-cyclonic Fastening - PIR13-RD04-4

Roofing

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

11MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Insulated Box Gutter Detail - PIR13-RD07-1

Roofing

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

12 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Expansion Step Detail - PIR13-RJ01-4

Roofing

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

14 GAUGE TEK SCREWS WITH CYCLONE WASHERS TO EVERY RIB (TYPICAL)

2° MINIMUM PITCH

METECNOSPAN ROOF

TURN UP PAN TO FULL RIB HEIGHT (SPECIALTOOL AVAILABLE)

250150

COLORBONDFLASHING

TURN DOWN PANAPPROXIMATELY 20°(SPECIAL TOOLAVAILABLE)

14 GAUGE TEK SCREWSWITH CYCLONEWASHERS TO EVERYRIB (TYPICAL)

50mm ROOF STEP

50

20

300300

4mm STEEL RIVETS @300 CTRS (TYPICAL)

ROOF SUPPORT STRUCTURE

COLORBOND TRIM FLASHING IF REQUIRED

MINERAL WOOL INFILL (IF REQUIRED)C

OP02DETAIL

13MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Roof End Lap Detail - PIR13-SL01-3

Roofing

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

METECNOSPAN

METECNOSPAN

SECURELAP SEAL STRIP & FIXING PLATE

12 x 25 ROOFZIP WITH MULTISEAL THROUGH UPPER SHEET & SECURELAP FIXING PLATE

TURN UP ROOF PANS TO FULL RIB HEIGHT (SPECIAL TOOL AVAILABLE)

TURN DOWN PAN20°(SPECIAL

TOOL AVAILABLE)

MINIMUM 200mmEND LAP CUTBACK

OVERHANG (AUST. STD)

PURLIN / ROOFSUPPORT STRUCTURE

COP02

DETAIL

IF LESS THAN 1500mm BETWEEN PURLINS AT END

LAP JOINT 10mm PACKER REQUIRED ON UPPER PURLIN

2510

10mm PVC PACKER (IF REQUIRED SEE BONDOR)

14 GAUGE TEK SCREW WITH MULTISEAL WASHER

WAFERTEK SCREW FIXED THROUGH PURLIN (TYPICAL) 14 GAUGE TEK SCREW

WITH NEO THROUGH SECURELAP & FIXING PLATE

25mm PVC PACKER (AVAILABLE FROM BONDOR ON REQUEST)

14 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Insulated Valley Boxed Gutter - PIR13-RV01-1

Roofing

METECN- ROO

INSULATEBOXED

Descripti

Description

Title

RevDate

Limited trading as Bondor. It ismay not be reproduced or its cwritten authority.

Metecno Ptytrading as

www.bondor1300 300 0

44 096 40

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

15MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Eaves Gutter Detail - PIR13-WC03-2

Roofing / Cladding

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

16 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Eaves Gutter Detail 2 - PIR13-WC04-2

Roofing

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

17MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

18 MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

19MetecnoSpan® Construction - Technical Drawings v3 - Current 05/02/2020

Standard Constructionmetecnospan®

Note: • We recommend that you should engage your local Bondor® architectural specialist at design stage to ensure the panel system is designed to suit specific project requirements.• All exposed core material is to be encapsulated with a non-combustible covering in order to achieve a BAL-40 or less.• Panel by Bondor®, screw may be by Bondor®, all other items by others.• Additional construction details are available through the Bondor® Website Client Portal or by contacting a local Bondor® representative. www.bondor.com.au• This drawing is copyright and the property of Metecno Pty Limited trading as Bondor®. It is subject to their legal recall and may not be reproduced or it’s contents divulged without written authority.

www.bondor.com.au

1300 300 099

BRISBANE/EXPORT 103 Ingram Road Acacia Ridge QLD 4110 Ph: (07) 3323 8500 Fax: (07) 3323 8501

PERTH 17 Gauge Circuit Canning Vale WA 6155 Ph: (08) 9256 0600 Fax: (08) 9256 0620

ADELAIDE 70-72 Rundle Road Salisbury South SA 5106

Ph: (08) 8282 5000 Fax: (08) 8282 5099

MELBOURNE 329A St Albans Road Sunshine VIC 3020 Ph: (03) 8326 8000 Fax: (03) 8326 8099

LAUNCESTON 7 Connector Park Drive Kings Meadows TAS 7249

Ph: (03) 6335 8500 Fax: (03) 6335 8544

SYDNEY 49-53 Newton Road Wetherill Park NSW 2164

Ph: (02) 9609 0888 Fax: (02) 9729 1114

Leaders in Thermal & Architectural Building Solutions

** Limited availability. ^ Darker colours warranted for use in limited regions. Metecno Pty Limited. ABN 44 096 402 934. The manufacturer reserves the right to change the specification without notice. Bondor®, LuxeWall®, MetecnoInspire®, Equitilt®, BondorPanel®, FlameGuard®, MetecnoPanel®, EconoClad®, MetecnoKasset®, InsulWall®, LuxeWall®, DesignerWall®, SolarSpan®, InsulRoof®, MetecnoSpan®, Purline®, Equideck®, InsulLiving®, EconoClad®, Metecno are trademarks of Metecno Pty Limited. BlueScope, Colorbond®, Permagard® and colour names are trademarks of BlueScope Steel Limited. Microban® is a registered trade mark of the Microban Products Company. The colours shown in this publication have been reproduced to represent actual product colours as accurately as possible. However, given printing limitations, we recommend checking your chosen colour against an actual sample before placing orders. This advice is of a general nature only. Designers must provide for adequate structural performance and other Building Code requirements. This information is subject to change. Refer to Bondor® website for latest version. Consult Bondor® for your application. BON0535 Drawing Pack - MetecnoSpan v3 05/02/2020