MCC3

Charging Cart

User Guide

DUKANE CORP AV SERVICE DEPT2 9 0 0 Du ka n e Dr iv e S t C h a r l e s, I L 6 0 1 7 48 0 0� 6 7 6 � 2 4 8 7F a x 6 3 0� 5 8 4� 5 1 5 6a v s er v ic e @ d u ka n e. c o mh t tp : / /w w w . d u ka n e. c o m /a v / s er v ic e /

975mm

430-MCC3-03

Step 1

T h is as s e m b ly c a n r e q u i r e2p e op l e.At t a co n eAttach the 4 wheels using the bolts,

the flat, and the lock washers.Locate the lock washer between theflat washer and the wheel plate. Theflat washer goes on the bolt followedby the lock washer.

Step 2

Open cart rear doors. Use key if locked.Then push on lower region of thehandle to release the door lockhandle.

Step 3

Us e t h e s

O p e n ta n d l oc o n n eP o w e r c C o n n e c t

Install the supplied power cables whichhave a C14 plug for the power outlet stripand a female plug for the power adapter device.

Power cable

C5 plug. Connect to thepower adapter.

C14 plug for the power strip.

Open the reardoor and loadin the poweradapters andpower cables.

Install and arrange thecables.

Step 4U c h a i n fo r se cu r i ty l a p to p p r i n te r sl o c a te d o n t he wo r k p l a t fo rm .Two "U" fastener locations for security ofthe cart and devices placed on the topsurface.

Step 5

5 ” La s te r sb ra ke lo c k( 2 r ig i d / 2 l in g )Po w e r s w i t c h fo r 4 o u t l e tPu s h bu t to n u n de r t he b re a ke r to tu r no n t he p o we r o n fo r 4 o u t le tm o d u le.W he n c a r t i s p l u g ge d i n to t he w a l l a l l 4o u t le t s c a n o pe r a te u n le s s t he c h a r g i n gp ro g r am i s ru n n i n g.T he c h a r g i n g de v i ce s w i l l re q u i re fu l l c a r tp o we r a n d t he 4 o u t le t s h a ve n o p o we rw he n t he c h a r g i n g p ro g r am i s o pe r a t i n g.

Tips!

4 Outlet power strip on side of cart

Step 6

Arrange the cables

Sun 09:30:15

Now 2012 / 01/ 01

EXIT CH1 CH2 CH3

1. Default Charging

2. set now

3. Reservation

4. set time

5. sw version

Se l e c t * to s w i t c h t h e t im e a n d t h e m e n u.

* Op t i o n a lse t t i n g.* P re s s “ E S C ” t o h o l d c h a r g i n g a n d p re s s “ E n te r ” t o c o n t i n u e c h a r i n g w h e n d o i n g t h e c h a r g i n g p ro g r am .* P re s s “ E S C ” a n d h o l d o n fo r 4 se c t o e s c a p e t h e p re se n t s c re e n.* T h e O S D w i l l j um p t o t h e s c re e n o f p re se n t t im e i f t h e se t t i n g a c t i o n i s p a u se d o v e r 6 0 se c.t o e xe c u te t h e c h a r g i n g 0. 5~ 4 h r by e a c h c h a n n e l se t t i n g.A L L: t h ro u g h S u n t o S a tMV F : t h ro u g h M o n t o F r iS u n. M o n. T u e . We d. T h u. F r i. S a t. : e v e ry s i n g l e d ayt h e s t a t u s o f O N a n d O F Ft h e t im e t o s t a r t t h e c h a r g i n gt o se t u p t h e p re se n t t im e .

2 h r s f a s t m o d e t o e a c h c h a n n e l_ + E n te rt o c h e c k c u r re n t c h a r g i n g se t t i n g.t o u p d a te t h e se t t i n g.1. Set now

2. see project

S o f t w a re v e r s i o nB a t te ry s t a t u ssw ver : 0.04

battery : 3.12V

ITEM:01 ALL

T:02:00 RUN

1. Reservation

2. see project

T he in te r io r o u t l e ts w i l l ha ve po we r o n ly a f te r t he" O S D " p ro g ra m i s f i n a l iz e d.T he co n t ro l le r ca n be p ro g ra m e d o n ly a f te r t h e ca r ti s p l u g g e d i n to a wa l l o u t le t.

Setup of Control - On Screen Display (OSD)

BaTips!

Quick Starting the cart 1.Plug in the cart power cord. The controller automatically comes ON. There is no OFF/ON switch. 2.Install the 2 AAA batteries in the control unit by opening the screw closed door and inserting thebatteries.3.Set the current time and date by using the control LCD On Screen Display (OSD) and the buttonsbelow it. When starting the LCD will display the “Weekday, time, NOW and the date”. Also the leftside LED will be ON. •Press the ESC button to get the main menu which will show “ 1. Def charging 2. Charge Time”. •Then move down to “4. Set time” by using the “-“ button. The blinking cursor needs to be on the“Set time” level. •Next press the “Enter “ button 2 times to get the blinking cursor on the time / day display. •Then use the - and + buttons with the blinking cursor to obtain the correct time / date values. •Use the “Enter” button to store each value. •Upon completion, press the ESC button twice to return to the main menu or display.4.Activating the charging system; •Press the ESC button to get the menu item “1. Def. charging” with the cursor present. •Then press Enter and the menu will go to “C1 Run” and a message like “E:21:19” and the cartwill start the default charging cycle. The default program for charging the power outlet strips at 2 hrper strip should now be operating. •The LED corresponding to one of the 3 channels (CH ) should be on. •When the CH 1, 2, or 3 LED is ON that power strip is active.If you get into a locked state, you can disconnect power to the cart by removing the power cord plugfrom the bottom of the CH1 power strip for 5 seconds. This resets the program to the start. 5.Close the rear door

1. Def Charging

2. Charge time

3. schedule

4. set time

5. information

to execute the charging 0.5~4hr by each channel setting.

ALL:through Sun to SatM-F:through Mon to FriSun. Mon. Tue. Wed. Thu. Fri. Sat.: every single daythe status of ON and OFFthe time to start the charging

to set up the present time.

2hrs fast mode to each channel

to check current charging setting.

to update the setting.

1. charge time

2. view settings

Software versionBattery status

sw ver : 0.04battery : 3.12V

ITEM:01 ALL

T:02:00 RUN

1. Reservation2. view settings

Ca n h o l d u p to a s c re e n s i z e o f 1 4 " fo r s o m e m o d e l s .CO p t i o n a l

w i t h a l l t he n e ce s s a ry pa r ts . co m p l e te

Ba t te r y Po we r co r dCa b l e T i e s( 3 6p c s ) A P H o l d e rKe y

Accessory

Feature

M a n u a lU s er ’ sm an u a l

36 pcs.

4 Power outlets on outside for external use. They operate when theinner charging system is not in use.

Swiveling 5" casters ( 2 with brake locks ).

components

Charging Control unit The cursor indicating the active line of the display is a flashing black box or a character. The white lighted LED shows the status of the charging system. When ON the left most

LED “EXT” indicates the charging is not active. The other 3 LEDs indicate if a channel (power strip of 12 outlets) is active. For example the “CH 1” LED being ON indicates the channel 1 strip is active with power to the outlets.

To pause the charging press the ESC button on the left. The left “EXT” LED comes ON The cart completes only one full cycle of the 3 Channels (the 3 power outlet strips). To clear the menu operation, disconnect the power input plug from the bottom of the left

side power strip. Use the ESC button to get to the top menu level. If there is no load on a power strip the controller will advance to the next Channel in 2

minutes. The 4 outside power outlets will not be available when the charging program is operat-

ing. Turing on the power to the cart. On Screen Displays (OSD) Example. “ Wed 14:45:50” Date and time ( Hour:min:sec) “New 2014/01/09” ( Year/Month/day) Set the time if first time operation . Push ESC button and go to menu item “4. Set time.” For Default 2 hour charging. Push ESC button to get the menu “ 1. 2 Hr charging -cursor flashing ” Push ENTER button. Will get a display that shows the Run End time for the Channels. Now Ex, “C1 Run E 16:45” Indicates CH 1 will run, charging, till ending at 4:45pm. Also “ C2 Stop E18:45 “ Indicates CH 2 will run, charging, till ending at 6:45pm The CH 1 LED will be ON showing the charging has started for the CH 1 power strip. After 2 hours Ch 1 will switch OFF at 4:45, and the charging will start on Channel 2 power strip.

MENU (OSD) Press “ESC” button to get menu 1. “ Def Charging” Default Charging The default is a 2 hr charge to each channel (Outlet Strip). Each outlet strip has a channel number. To start the charging press ENTER button The CH1 LED should come on.

The OSD should show the message “C1 Run E XX:00 “ indicating the End time for the Channel 1 charge.

2. Charge time Use for the custom charge time Controls the charging time period for a channel. ( 0.5 to 4 hours )

1.Charge time; Use to set the charging time period for a channel. Press ENTER to get “C1 T=2.0 Hr

Change to the desired time, Will get “Run(Y/N)=?N” or “Y” Use -/+ buttons to get desired. Then Press ENTER . Repeat for other Channels. Get display : “Select” “C1/C2/C3(Y/N)? N” or Y Get

desired N or Y and press ENTER. Get display “ Confirm” For confirmation press ENTER.

This will start the Charging cycle. 2. View settings; Use to check the current settings. Can also modify them.

Same routine as prior menu level.

3. Schedule Used to set the days and the time of day the cart will automatically start the charging cycle. Also can set the time duration for the charging on each Channel.

1. Reservation Use to make the settings. Press ENTER. Display is “01 All 02:00” Program 1 is set for all (All) the

week days to start the charging at 2 AM. Also get “02 Mon 04:00” Program 2 is for Monday only to start at

4 AM Can select the day and time. There are 8 choices Then can set the charge time for the Channels. For example; “C1 T=0.5 Hr” When the programming is completed press ENTER. Get display ; “Select” “C1/C2/C3(Y/N)? N” or Y Get

desired N or Y and press ENTER. Get display “ Confirm” Press ENTER. This will start the charging on specified day and time.

2. View settings ( This is a view of the current settings )

4. Set time (To set the control unit to the present time and date) 1. Set the time Press ENTER

Set time , day month , year. Use the -/+ buttons 2. See Time Use to check the time settings.

5. Information (Software Version) and the AA battery voltage

MCC3 CHARGING CONTROL UNIT

Buttons; ESC - + ENTER

5

5 Caution; Push button for turning all the charging power strips ON . Use only if total charging

load is under 11 amps. Note that all 3 LEDs are ON. Push button again to turn OFF.

Timer Ver 0.11A