147 ©

REMOVE REAR SUPPORTMODIFY CAVITY

MINI STAN DIN ISO DIN

TUNERS / CASSETTE / DISC PLAYERS RADIOEQ

STACKSINGLEDBL DIN

APPLICATION KIT MODEL: DIN1190 (SHAFT)

HARNESS ADAPTOR: MA02 ANTENNA ADAPTOR:

IN-DASH INSTALLATION AREA DIMENSIONS

DEPTH WIDTH HEIGHTMAX

DEPTH

CAVITY 71/4" 71/4" 75/32"

TYPE: DIN X 2 75/32" 23/32"DASHOPENING

DASH MATERIAL: PLASTIC THICKNESS: 1/8"

FOR MAX DEPTH

AMPLIFIER/EQ MOUNTING LOCATIONS (WxHxD)

CONSOLE UNDER GLOVE TRUNK/SEAT BOX CARGO

K5 = WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATEKIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER.

KS = SCOSCHE KIT RECOMMENDED.N = NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED.P = PERFECT WITHOUT MODIFICATION.P1 = MODIFY OR REMOVE POCKETS.P2 = COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT).P3 = PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT.R = REAR LOAD ISOMOUNT.U = UNDERDASH.W1 = WITH POWER WINDOWS ONLY.W2 = WITHOUT POWER WINDOWS ONLY.

IN DASH APPLICATION NOTES

CHASSIS H 13/4-2 2 2 2 37/8 3

CHASSIS W 71/8 71/8 71/8 7 71/8 71/8

CHASSIS D 43/4-51/2 57/8-6

11/16 57/8-611/16 57/8-6

11/16 57/8-611/16 57/8-6

11/16

NOSE H 15/8-13/4 15/8-1

3/4 23/8 113/16 33/4-4

NOSE W 41/8-43/16 41/8-4

3/16 71/2 611/16 611/16-71/4

SHAFT SP. 51/8-53/4 51/8-6

NO

TE

:T

HIS

MA

NU

AL

IS B

AS

ED

ON

CA

RE

FU

LLY

DO

CU

ME

NT

ED

RE

SE

AR

CH

. AB

SO

LUT

EA

CC

UR

AC

Y IS

AT

TE

MP

TE

D B

UT

NO

T G

UA

RA

NT

EE

D. U

SE

TH

IS M

AN

UA

L A

S A

RE

FE

RE

NC

EG

UID

E. S

CO

SC

HE

, IN

C. C

AN

NO

T B

E R

ES

PO

NS

IBLE

FO

R IN

CO

NS

IST

EN

CIE

S T

HAT

MAY

OC

CU

R.

KS KS P K4 K4 N

B = BACK UP PLATES REQUIRED.C1 = CUT TRIM/PLASTIC (STRUCTURE).C2 = CUT STEEL.D = BELOW DECK ONLY.D1 = LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT).D2 = CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK.D3 = NARROW SURFACE, BELOW DECK ONLY.F1 = MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING.F2 = MODIFY DASH CAVITY AND/OR PANEL.K = INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED.K1 = KIT MODIFICATIONS REQUIRED.K2 = EXTENSION KIT RECOMMENDED.K3 = WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO.K4 = FABRICATE PANEL/BRACKETS.

MAZDA1998-UP MIATAConvertible

Dimensions shown are inches.For inch/mm conversions refer to chart section.

UPDATEDTHROUGH

'99200020012002

23/32"

Various

DASH.

148 ©1998 SCOSCHE INDUSTRIES, INC.

FACTORY 2 X DIN DASH OPENING - NOTICE REMOVABLE DIVIDER BAR. FRONT DOOR PANEL.

FRONT DOOR 6 X 8" PROVISION ADAPTER.

TWEETER PROVISION IN DOOR PANEL.

1998-UP MAZDA MIATACONVERTIBLE

PRELIMINARY: DISCONNECT THE NEGATIVE BATTERY CABLE.

ANTENNA: THE FACTORY ANTENNA IS LOCATED ON THE LEFT REARFENDER.

RADIO REMOVAL AND IN-DASH INSTALLATION:NOTE: THE FACTORY STEREO PROVISION IS FOR A DIN SNAP-IN STYLE

RADIO.1. UNSNAP COVERS FROM THE SIDES OF THE RADIO’S FACEPLATE2. INSERT FORD-TYPE RADIO RELEASE TOOLS, RELEASE THE RADIO FROM

THE DASH, UNPLUG AND REMOVE RADIO.

FRONT DOOR SPEAKER INSTALLATION:NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 6 X 8" SPEAKER IN A

FACTORY ADAPTER.1. EXTRACT (2) PUSH PIN FASTENERS FROM THE REAR EDGE OF THE

DOOR PANEL AND (1) FROM THE TOP FRONT CORNER.2. EXTRACT (1) SCREW FROM DOOR RELEASE HANDLE CUP ASSEMBLY,

UNCLIP AND REMOVE.3. EXTRACT (1) SCREW FROM THE TOP OF THE DOOR PULL HANDLE.4. REMOVE CARPET STRIP FROM ARMREST CUP AND EXTRACT (1) SCREW

FROM BEHIND.5. USING A PANEL REMOVAL TOOL, RELEASE THE PANEL FASTENERS

AROUND THE PERIMETER OF THE DOOR PANEL THAN LIFT PANEL UPAND AWAY FROM DOOR TO REMOVE.

6. EXTRACT (4) SCREWS FROM SPEAKER ADAPTER UNPLUG, AND REMOVEASSEMBLY.