Maricopa County Community College District. South … E...Antenna Orientation: KJZZ ERI SHPX‐12AC‐HW 51 Degrees True KBAQ ERI MP‐10AC‐DA‐HW 1 – 3 Degrees True, Actual to

(2) dB Products 420 or Equiv. (2 runs ½” Andrew)

ERI SHPX‐12AC‐HW 91.5 Mhz.

KJZZ (4 1/16” Andrew)

ERI MP‐10AC‐DA‐HW 89.5 Mhz.

KBAQ (3 1/8” Andrew)

Exalt 2’ w TX/RX ODU

Andrew HP‐6 (EW‐90)

Mark‐P‐9A72GNU ( ½” Andrew) Shively 6828‐4 (4 1/16”)

193.57ft

240 ft.

175 – 235 ft

144.3 ft.

120 – 170 ft.

85.3 ft.

106 ft.

102 ft. 112 ft.

Maricopa County Community College District. South Mountain Electronic Site, Phoenix, AZ. Antenna Placements.

11/7/2014 DVA

210 ft.

Antenna Orientation:

KJZZ ERI SHPX‐12AC‐HW 51 Degrees True

KBAQ ERI MP‐10AC‐DA‐HW 1 – 3 Degrees True, Actual to be determined by Test Range data.

SHARED AUX, SHIVELY 6828‐4 340 Degrees True

Andrew HP6 43.8 Degrees True

Mark Products P‐9A72GNU 43.8 Degrees True

Exalt 2’ Spread Spectrum 43.8 Degrees True

Painting and Marking Specifications

FCC Part 1, 3, 11, 21

LED Lamps at 120 ft. Level

LED L‐864 Code Beacon at 240 – 243 Ft. Level.

Tower Loading

TIA ‐222‐G or Higher

70 MPH Sustained Wind, 90 MPH 3 second Gust

Topographic Category 4

Allow Capacity for 2 additional communication antennas, DB‐420 or equiv. at 210 ft. level using ½” lines.

11/13/2014 ERI - FM Antennas

http://www.eriinc.com/Catalog/Antennas/FM-Antennas.aspx 1/4

Catalog > Antennas > FM Antennas

FM Antennas

ERI is the world's largest supplier of antennas used by broadcast stations. We entered thebusiness of manufacturing FM antennas in the earliest days of FM radio and continue to servethe changing needs of FM broadcasters with the industry’s best products.

ROTOTILLER ® X Series Circularly Polarized FM Antenna

The ROTOTILLER X Series circularly polarized FM (88 - 108 MHz) antenna combines the exceptionalengineering features of an internally fed, fully pressurized system with superior fabrication characterizedby totally welded feed connections, rugged brass material and TIG welding. The ROTOTILLER X Series isavailable in low, medium, and super high power versions and is suitable for single frequency ormultiplexed applications.

Product Line: ROTOTILLER

Polarization: Circular

Maximum Power Rating 120.00 kW

ROTOTILLER ® Circularly Polarized FM Antenna

The original ROTOTILLER circularly polarized FM (88 - 108 MHz) antenna combines the exceptionalengineering features of an internally fed, fully pressurized system with superior fabrication characterizedby totally welded feed connections, rugged brass material and TIG welding. The ROTOTILLER is availablein low, medium, and super high power versions; capable for single frequency or multiplexed operations;and suitable for directional applications.

Product Line: ROTOTILLER

Polarization: Circular

Maximum Power Rating 120.00 kW

ROTOTILLER ® Rotofiller Series Circularly Polarized FM Antenna

The ROTOTILLER Rotofiller Series circularly polarized FM (88 - 108 MHz) antenna combines theexceptional engineering features of an internally fed, fully pressurized system with superior fabricationcharacterized by totally welded feed connections, rugged brass material and TIG welding. The RotofillerSeries provides reduced downward radiation lessening interference with ground level equipment and

Copyright © 2013 Electronics Research, Inc. All rights reserved.Printed in USA (No. 20090316002_AEN Revision 03 | 2013 10 22)Your Single Source for Broadcast Solutions™ | www.eriinc.com | 877 ERI-LINE

ROTOTILLER® X SeriesCircularly Polarized FM Antenna

MPX Series ROTOTILLER® FM Antenna

ERI antennas are unchallenged in quality and dependability. ERI is the only manufacturer to use large diameter outer conductors and a completely enclosed, pressurized, internal series feed system. The result is a simple and reliable method of coupling power to the elements. Unlike competing designs, ERI series fed antennas do not require a troublesome secondary current loop for element excitation with all the resulting disadvantages. All ERI antennas include brackets for mounting on leg, pole, or face mounting (up to 42-inch uniform cross section tower); brackets for other mounting configurations are optionally available.

ERI’s original and distinctive design combines the exceptional engineering features of an internally fed, fully pressurized system with superior fabrication characterized by totally welded feed connections, rugged brass material and TIG welding. The ROTOTILLER® X Series FM antenna’s unique design consists of two series fed, bent dipole elements which form a space phased, circularly polarized radiator. The antenna’s configuration and the large diameter of the radiating elements contribute to the excellent bandwidth of the antenna system, and also inhibits corona discharge.

The horizontally polarized horizontal plane azimuth pattern of the SHPX series antenna is omnidirectional within ±2 dB when the antenna is pole or LAMBDA™ Optimized Mounting System mounted atop a tower. Side mounting the antenna on a typical tower structure will affect the azimuth pattern. ERI offers a pattern measurement service to assist in determining the effect of the mounting structure on the antenna’s pattern. Using ERI’s pattern optimization service, the pattern’s circularity may be improved through the addition of parasitically excited elements.

Benefits• Low VSWR, superior VSWR band

width, and minimal weather related VSWR problems

• Fully pressurized, internal feed and welded feed connections

• High input power capacity• Modular construction facilitates easy installation and

repair• Rugged brass construction and stainless steel support

brackets and hardware – Corrosion resistant construction• Radomes or deicing heaters not normally required for

radial ice less than 1/2-inch; however radomes or deicing heaters are available

• Quarter Wave Stub included

CharacteristicsProduct Line ROTOTILLER®

Product Series X Series

Frequency Range 88 - 108 MHz, Single frequency or multiplexed versions

Polarization Circular (Clockwise)

Azimuth ± 2 dB in free space

Axial Ratio Less than 3 dB in free space

VSWR at Input 1.07:1 or less (with field matching) 1.25:1 or less (with top pole or LAMBDA™ Mounting System) 1.50:1 or less (top mounted without field matching)



Electrical Specifications

Type Number Number of Bays

Power Gain dB Gain Input Type Feed

ConfigurationInput Power Rating Bay to Bay

SpacingkW

SHPX-1AE 1 0.461 -3.3623 3 1/8 inch 50 Ohm Female End 32.0 Full Wave

SHPX-1BE 1 0.461 -3.3623 6 1/8 inch 50 Ohm Female End 40.0 Full Wave

SHPX-2AC 2 0.997 -0.0128 3 1/8 inch 50 Ohm Female Center 39.0 Full Wave

SHPX-2AC6 2 0.997 -0.0128 6 1/8 inch 50 Ohm Female Center 64.0 Full Wave

SHPX-2AE 2 0.997 -0.0128 3 1/8 inch 50 Ohm Female End 32.0 Full Wave

SHPX-2BC 2 0.997 -0.0128 6 1/8 inch 50 Ohm Female Center 80.0 Full Wave

SHPX-2BE 2 0.997 -0.0128 6 1/8 inch 50 Ohm Female End 56.0 Full Wave

SHPX-2CE 2 0.997 -0.0128 6 1/8 inch 50 Ohm Female End 80.0 Full Wave

SHPX-3AC 3 1.559 1.9278 3 1/8 inch 50 Ohm Female Off Center 39.0 Full Wave

SHPX-3AC6 3 1.559 1.9278 6 1/8 inch 50 Ohm Female Off Center 64.0 Full Wave

SHPX-3AE 3 1.559 1.9278 3 1/8 inch 50 Ohm Female End 32.0 Full Wave

SHPX-3BC 3 1.559 1.9278 6 1/8 inch 50 Ohm Female Center 112.0 Full Wave

SHPX-3BE 3 1.559 1.9278 6 1/8 inch 50 Ohm Female End 56.0 Full Wave

SHPX-4AC 4 2.133 3.2903 3 1/8 inch 50 Ohm Female Center 39.0 Full Wave

SHPX-4AC6 4 2.133 3.2903 6 1/8 inch 50 Ohm Female Center 64.0 Full Wave




SHPX-4CE 4 2.133 3.2903 6 1/8 inch 50 Ohm Female End 120.0 Full Wave









SHPX-6CE 6 3.303 5.1888 6 1/8 inch 50 Ohm Female End 120.0 Full Wave



SHPX-7BC 7 3.894 5.9034 6 1/8 inch 50 Ohm Female Off Center 112.0 Full Wave
















SHPX Model - Super High Power







SpacingkW

SHPX-2AC6-HW 2 0.702 -1.5366 6 1/8 inch 50 Ohm Female Center 64.0 Half Wave

SHPX-2AC-HW 2 0.702 -1.5366 3 1/8 inch 50 Ohm Female Center 39.0 Half Wave

SHPX-2AE-HW 2 0.702 -1.5366 3 1/8 inch 50 Ohm Female End 32.0 Half Wave

SHPX-2BC-HW 2 0.702 -1.5366 6 1/8 inch 50 Ohm Female Center 80.0 Half Wave

SHPX-2BE-HW 2 0.702 -1.5366 6 1/8 inch 50 Ohm Female End 56.0 Half Wave

SHPX-2CE-HW 2 0.702 -1.5366 6 1/8 inch 50 Ohm Female End 80.0 Half Wave

SHPX-3AC6-HW 3 1.012 0.0518 6 1/8 inch 50 Ohm Female Off Center 64.0 Half Wave

SHPX-3AC-HW 3 1.012 0.0518 3 1/8 inch 50 Ohm Female Off Center 39.0 Half Wave

SHPX-3AE-HW 3 1.012 0.0518 3 1/8 inch 50 Ohm Female End 32.0 Half Wave

SHPX-3BC-HW 3 1.012 0.0518 6 1/8 inch 50 Ohm Female Center 112.0 Half Wave

SHPX-3BE-HW 3 1.012 0.0518 6 1/8 inch 50 Ohm Female End 56.0 Half Wave

SHPX-4AC6-HW 4 1.307 1.1628 6 1/8 inch 50 Ohm Female Center 64.0 Half Wave

SHPX-4AC-HW 4 1.307 1.1628 3 1/8 inch 50 Ohm Female Center 39.0 Half Wave




SHPX-4CE-HW 4 1.307 1.1628 6 1/8 inch 50 Ohm Female End 120.0 Half Wave









SHPX-6CE-HW 6 1.913 2.8171 6 1/8 inch 50 Ohm Female End 120.0 Half Wave



SHPX-7BC-HW 7 2.217 3.4577 6 1/8 inch 50 Ohm Female Off Center 112.0 Half Wave























SpacingkW

MPX-1E 1 0.461 -3.3623 3 1/8 inch 50 Ohm Female End 12.0 Full Wave

MPX-2C 2 0.997 -0.0128 3 1/8 inch 50 Ohm Female Center 18.0 Full Wave

MPX-2E 2 0.997 -0.0128 3 1/8 inch 50 Ohm Female End 18.0 Full Wave

MPX-3C 3 1.559 1.9278 3 1/8 inch 50 Ohm Female Off Center 18.0 Full Wave

MPX-3E 3 1.559 1.9278 3 1/8 inch 50 Ohm Female End 18.0 Full Wave

MPX-4C 4 2.133 3.2903 3 1/8 inch 50 Ohm Female Center 18.0 Full Wave





MPX-7C 7 3.894 5.9034 3 1/8 inch 50 Ohm Female End 18.0 Full Wave






MPX-2C-HW 2 0.702 -1.5366 3 1/8 inch 50 Ohm Female Center 18.0 Half Wave

MPX-2E-HW 2 0.702 -1.5366 3 1/8 inch 50 Ohm Female End 18.0 Half Wave

MPX-3C-HW 3 1.012 0.0518 3 1/8 inch 50 Ohm Female Off Center 18.0 Half Wave

MPX-3E-HW 3 1.012 0.0518 3 1/8 inch 50 Ohm Female End 18.0 Half Wave

MPX-4C-HW 4 1.307 1.1628 3 1/8 inch 50 Ohm Female Center 18.0 Half Wave











MPX Model - Medium Power







SpacingkW

LPX-1E 1 0.461 -3.3623 1 5/8 inch 50 Ohm Female End 9.0 Full Wave

LPX-2C 2 0.997 -0.0128 3 1/8 inch 50 Ohm Female Center 12.0 Full Wave

LPX-2E 2 0.997 -0.0128 1 5/8 inch 50 Ohm Female End 9.0 Full Wave

LPX-3C 3 1.559 1.9278 3 1/8 inch 50 Ohm Female Off Center 12.0 Full Wave

LPX-3E 3 1.559 1.9278 1 5/8 inch 50 Ohm Female End 9.0 Full Wave

LPX-4C 4 2.133 3.2903 3 1/8 inch 50 Ohm Female Center 12.0 Full Wave











LPX-2C-HW 2 0.702 -1.5366 3 1/8 inch 50 Ohm Female Center 12.0 Half Wave

LPX-2E-HW 2 0.702 -1.5366 1 5/8 inch 50 Ohm Female End 9.0 Half Wave

LPX-3C-HW 3 1.012 0.0518 3 1/8 inch 50 Ohm Female Off Center 12.0 Half Wave

LPX-3E-HW 3 1.012 0.0518 1 5/8 inch 50 Ohm Female End 9.0 Half Wave

LPX-4C-HW 4 1.307 1.1628 3 1/8 inch 50 Ohm Female Center 12.0 Half Wave











LPX Model - Low Power



Mechanical Specifications

Type Number

Weight CaAa

Antenna Antenna & ½ in. radial ice Antenna & radome Antenna, radome,

½ in. radial ice Antenna Antenna & ½ in. radial ice

Antenna with radome

Antenna, radome, & ½ in. radial ice

lbm kg lbm kg lbm kg lbm kg ft2 m2 ft2 m2 ft2 m2 ft2 m2

SHPX-1AE 107.00 48.53 187.00 84.82 157.00 71.21 312.00 141.52 4.69 0.44 5.93 0.55 8.98 0.83 10.26 0.95

SHPX-1BE 155.00 70.31 255.00 115.67 205.00 92.99 380.00 172.37 5.28 0.49 6.57 0.61 9.56 0.89 10.90 1.01

SHPX-2AC 250.00 113.40 410.00 185.97 350.00 158.76 660.00 299.37 11.13 1.03 14.73 1.37 19.69 1.83 23.38 2.17

SHPX-2AC6 315.00 142.88 480.00 217.72 415.00 188.24 730.00 331.12 12.50 1.16 15.78 1.47 21.06 1.96 24.43 2.27

SHPX-2AE 220.00 99.79 380.00 172.37 320.00 145.15 630.00 285.76 9.99 0.93 12.96 1.20 18.55 1.72 21.61 2.01

SHPX-2BC 415.00 188.24 600.00 272.16 515.00 233.60 850.00 385.55 13.33 1.24 16.33 1.52 21.89 2.03 24.98 2.32

SHPX-2BE 315.00 142.88 515.00 233.60 415.00 188.24 765.00 347.00 11.66 1.08 14.48 1.35 20.22 1.88 23.13 2.15

SHPX-2CE 345.00 156.49 575.00 260.82 445.00 201.85 825.00 374.21 14.00 1.30 16.83 1.56 22.75 2.11 25.48 2.37

SHPX-3AC 363.00 164.65 603.00 273.52 513.00 232.69 978.00 443.61 16.42 1.53 21.76 2.02 29.27 2.72 34.74 3.23

SHPX-3AC6 428.00 194.14 673.00 305.27 578.00 262.18 1048.00 475.36 17.79 1.65 22.81 2.12 30.64 2.85 35.79 3.32

SHPX-3AE 333.00 151.05 573.00 259.91 483.00 219.09 948.00 430.01 15.28 1.42 19.99 1.86 28.13 2.61 32.97 3.06

SHPX-3BC 575.00 260.82 860.00 390.09 725.00 328.85 1235.00 560.19 19.71 1.83 24.23 2.25 32.55 3.02 37.21 3.46

SHPX-3BE 475.00 215.46 775.00 351.53 625.00 283.50 1150.00 521.63 18.04 1.68 22.38 2.08 30.88 2.87 35.36 3.29

SHPX-4AC 476.00 215.91 796.00 361.06 676.00 306.63 1296.00 587.86 21.72 2.02 28.79 2.67 38.84 3.61 46.09 4.28

SHPX-4AC6 541.00 245.39 871.00 395.08 741.00 336.11 1371.00 621.88 23.09 2.15 29.84 2.77 40.21 3.74 47.14 4.38

SHPX-4AE 446.00 202.30 766.00 347.45 646.00 293.02 1266.00 574.25 20.58 1.91 27.01 2.51 37.70 3.50 44.32 4.12

SHPX-4BC 735.00 333.39 1105.00 501.22 935.00 424.11 1605.00 728.02 26.09 2.42 32.13 2.98 43.21 4.01 49.44 4.59

SHPX-4BE 635.00 288.03 1035.00 469.47 835.00 378.75 1535.00 696.26 24.42 2.27 30.28 2.81 41.54 3.86 47.59 4.42

SHPX-4CE 695.00 315.25 1155.00 523.90 895.00 405.97 1655.00 750.70 30.00 2.79 35.39 3.29 47.20 4.39 52.70 4.90

SHPX-5AC 559.00 253.56 959.00 435.00 809.00 366.96 1584.00 718.49 25.87 2.40 34.04 3.16 47.28 4.39 55.67 5.17

SHPX-5AC6 672.00 304.81 1152.00 522.54 972.00 440.89 1902.00 862.73 31.17 2.90 41.07 3.82 56.85 5.28 67.03 6.23

SHPX-5AE 559.00 253.56 959.00 435.00 809.00 366.96 1584.00 718.49 25.87 2.40 34.04 3.16 47.28 4.39 55.67 5.17

SHPX-5BC 895.00 405.97 1365.00 619.15 1145.00 519.36 1990.00 902.65 32.47 3.02 40.04 3.72 53.88 5.01 61.67 5.73

SHPX-5BE 795.00 360.61 1295.00 587.40 1045.00 474.00 1920.00 870.90 30.80 2.86 38.19 3.55 52.21 4.85 59.82 5.56

SHPX-6AC 702.00 318.42 1182.00 536.15 1002.00 454.50 1932.00 876.34 32.31 3.00 42.84 3.98 57.99 5.39 68.80 6.39

SHPX-6AC6 767.00 347.91 1262.00 572.43 1067.00 483.98 2012.00 912.63 33.68 3.13 43.89 4.08 59.36 5.51 69.85 6.49

SHPX-6BC 1055.00 478.54 1610.00 730.28 1355.00 614.62 2360.00 1070.48 38.85 3.61 47.94 4.45 64.54 6.00 73.90 6.87

SHPX-6CE 1045.00 474.00 1735.00 786.98 1345.00 610.08 2485.00 1127.18 46.00 4.27 53.96 5.01 71.66 6.66 79.91 7.42

SHPX-7AC 785.00 356.07 1345.00 610.08 1135.00 514.83 2220.00 1006.97 36.46 3.39 48.09 4.47 66.43 6.17 78.38 7.28

SHPX-7AC6 850.00 385.55 1425.00 646.37 1200.00 544.31 2300.00 1043.26 37.83 3.51 49.14 4.57 67.80 6.30 79.43 7.38

SHPX-7BC 1215.00 551.11 1855.00 841.41 1565.00 709.87 2730.00 1238.31 45.23 4.20 55.84 5.19 75.20 6.99 86.13 8.00

SHPX-8AC 928.00 420.93 1568.00 711.23 1328.00 602.37 2568.00 1164.83 42.90 3.99 56.89 5.29 77.14 7.17 91.51 8.50

SHPX-8AC6 993.00 450.42 1653.00 749.79 1393.00 631.85 2653.00 1203.38 44.27 4.11 57.94 5.38 78.51 7.29 92.56 8.60

SHPX-8BC 1375.00 623.69 2115.00 959.35 1775.00 805.13 3115.00 1412.94 51.62 4.80 63.75 5.92 85.86 7.98 98.36 9.14

SHPX-9AC 1136.00 515.28 1876.00 850.94 1586.00 719.40 3001.00 1361.23 50.71 4.71 66.74 6.20 89.22 8.29 105.69 9.82

SHPX-9AC6 1201.00 544.76 1961.00 889.49 1651.00 748.88 3086.00 1399.79 52.08 4.84 67.79 6.30 90.59 8.42 106.74 9.92

SHPX-9BC 1535.00 696.26 2375.00 1077.28 1985.00 900.38 3500.00 1587.57 58.01 5.39 71.66 6.66 96.52 8.97 110.59 10.27

SHPX-10AC 1154.00 523.45 1954.00 886.32 1654.00 750.24 3204.00 1453.31 53.49 4.97 70.95 6.59 96.29 8.95 114.21 10.61

SHPX-10AC6 1219.00 552.93 2044.00 927.14 1719.00 779.73 3294.00 1494.13 54.86 5.10 72.00 6.69 97.66 9.07 115.26 10.71

SHPX-10BC 1695.00 768.84 2620.00 1188.41 2195.00 995.64 3870.00 1755.40 64.38 5.98 79.56 7.39 107.19 9.96 122.82 11.41

SHPX-11AC 1172.00 531.61 2037.00 923.97 1722.00 781.09 3412.00 1547.66 56.27 5.23 75.16 6.98 103.36 9.60 122.73 11.40

SHPX-11AC6 1237.00 561.09 2127.00 964.79 1787.00 810.57 3502.00 1588.48 57.64 5.35 76.21 7.08 104.73 9.73 123.78 11.50

SHPX-11BC 1855.00 841.41 2865.00 1299.54 2405.00 1090.89 4240.00 1923.23 70.75 6.57 87.46 8.13 117.86 10.95 135.05 12.55

SHPX-12AC 1380.00 625.96 2340.00 1061.41 1980.00 898.11 3840.00 1741.79 64.07 5.95 85.00 7.90 115.44 10.72 136.92 12.72

SHPX-12AC6 1445.00 655.44 2435.00 1104.50 2045.00 927.60 3935.00 1784.89 65.45 6.08 86.05 7.99 116.81 10.85 137.97 12.82

SHPX-12BC 2015.00 913.99 3125.00 1417.48 2615.00 1186.14 4625.00 2097.86 77.15 7.17 95.36 8.86 128.51 11.94 147.28 13.68Notes: (1) Antenna weight and wind load are approximate values for a typical structure assuming no top load. Final design loads will vary for specific projects and should be verified by an ERI representative. (2) Wind loads are calculated in accordance with the ANSI/TIA/EIA 222-F standard. Weight and effective wind area (CaAc) includes antenna, inner transmission feed and typical support mast and mounting brackets with no ice.





Type Number

Weight CaAa



Antenna with radome



SHPX-2AC6-HW 301.00 136.53 458.00 207.75 401.00 181.89 708.00 321.14 11.00 1.02 13.44 1.25 19.56 1.82 22.09 2.05

SHPX-2AC-HW 236.00 107.05 388.00 175.99 336.00 152.41 638.00 289.39 9.57 0.89 12.67 1.18 18.13 1.68 21.32 1.98

SHPX-2AE-HW 206.00 93.44 358.00 162.39 306.00 138.80 608.00 275.78 8.39 0.78 10.68 0.99 16.95 1.57 19.33 1.80

SHPX-2BC-HW 395.00 179.17 565.00 256.28 495.00 224.53 815.00 369.68 11.55 1.07 13.72 1.27 20.12 1.87 22.33 2.07

SHPX-2BE-HW 295.00 133.81 480.00 217.72 395.00 179.17 730.00 331.12 9.37 0.87 11.74 1.09 17.93 1.67 20.39 1.89

SHPX-2CE-HW 317.00 143.79 527.00 239.04 417.00 189.15 777.00 352.44 10.88 1.01 13.25 1.23 19.44 1.81 21.90 2.03

SHPX-3AC6-HW 400.00 181.44 629.00 285.31 550.00 249.48 1004.00 455.41 14.70 1.37 18.18 1.69 27.54 2.56 31.16 2.89

SHPX-3AC-HW 335.00 151.95 559.00 253.56 485.00 219.99 934.00 423.66 13.27 1.23 17.41 1.62 26.11 2.43 30.39 2.82

SHPX-3AE-HW 305.00 138.35 529.00 239.95 455.00 206.38 904.00 410.05 12.09 1.12 15.42 1.43 24.93 2.32 28.40 2.64

SHPX-3BC-HW 535.00 242.67 790.00 358.34 685.00 310.71 1165.00 528.44 15.65 1.45 18.88 1.75 28.50 2.65 31.82 2.96

SHPX-3BE-HW 435.00 197.31 705.00 319.78 585.00 265.35 1080.00 489.88 13.47 1.25 16.90 1.57 26.31 2.44 29.88 2.78

SHPX-4AC6-HW 499.00 226.34 805.00 365.14 699.00 317.06 1305.00 591.94 18.39 1.71 22.93 2.13 35.51 3.30 40.24 3.74

SHPX-4AC-HW 434.00 196.86 730.00 331.12 634.00 287.58 1230.00 557.92 16.96 1.58 22.16 2.06 34.08 3.17 39.47 3.67

SHPX-4AE-HW 404.00 183.25 700.00 317.51 604.00 273.97 1200.00 544.31 15.78 1.47 20.17 1.87 32.90 3.06 37.48 3.48

SHPX-4BC-HW 675.00 306.17 1000.00 453.59 875.00 396.89 1500.00 680.39 19.30 1.79 23.78 2.21 36.43 3.38 41.09 3.82

SHPX-4BE-HW 575.00 260.82 930.00 421.84 775.00 351.53 1430.00 648.64 17.56 1.63 22.07 2.05 34.69 3.22 39.37 3.66

SHPX-4CE-HW 611.00 277.14 1011.00 458.58 811.00 367.86 1511.00 685.38 20.15 1.87 24.65 2.29 37.27 3.46 41.96 3.90

SHPX-5AC6-HW 598.00 271.25 976.00 442.71 848.00 384.65 1601.00 726.20 22.09 2.05 27.68 2.57 43.49 4.04 49.31 4.58

SHPX-5AC-HW 533.00 241.76 901.00 408.69 783.00 355.16 1526.00 692.18 20.66 1.92 26.91 2.50 42.06 3.91 48.54 4.51

SHPX-5AE-HW 503.00 228.16 871.00 395.08 753.00 341.56 1496.00 678.57 19.48 1.81 24.92 2.32 40.88 3.80 46.55 4.32

SHPX-5BC-HW 815.00 369.68 1225.00 555.65 1065.00 483.08 1850.00 839.15 23.40 2.17 28.94 2.69 44.80 4.16 50.58 4.70

SHPX-5BE-HW 715.00 324.32 1155.00 523.90 965.00 437.72 1780.00 807.39 21.66 2.01 27.23 2.53 43.06 4.00 48.86 4.54

SHPX-6AC6-HW 697.00 316.15 1152.00 522.54 997.00 452.23 1902.00 862.73 25.78 2.40 32.42 3.01 51.47 4.78 58.38 5.42

SHPX-6AC-HW 632.00 286.67 1072.00 486.25 932.00 422.75 1822.00 826.45 24.35 2.26 31.65 2.94 50.03 4.65 57.61 5.35

SHPX-6BC-HW 955.00 433.18 1435.00 650.90 1255.00 569.26 2185.00 991.10 27.05 2.51 33.84 3.14 52.73 4.90 59.80 5.56

SHPX-6CE-HW 905.00 410.50 1495.00 678.12 1205.00 546.58 2245.00 1018.31 29.41 2.73 36.06 3.35 55.10 5.12 62.01 5.76

SHPX-7AC6-HW 796.00 361.06 1328.00 602.37 1146.00 519.82 2203.00 999.26 29.47 2.74 37.16 3.45 59.45 5.52 67.45 6.27

SHPX-7AC-HW 731.00 331.58 1243.00 563.82 1081.00 490.33 2118.00 960.71 28.04 2.61 36.39 3.38 58.00 5.39 66.68 6.19

SHPX-7BC-HW 1095.00 496.68 1645.00 746.16 1445.00 655.44 2520.00 1143.05 30.70 2.85 38.74 3.60 60.66 5.64 69.02 6.41

SHPX-8AC6-HW 895.00 405.97 1499.00 679.93 1295.00 587.40 2499.00 1133.53 33.18 3.08 41.92 3.89 67.42 6.26 76.53 7.11

SHPX-8AC-HW 830.00 376.48 1414.00 641.38 1230.00 557.92 2414.00 1094.97 31.74 2.95 41.14 3.82 65.99 6.13 75.76 7.04

SHPX-8BC-HW 1235.00 560.19 1870.00 848.22 1635.00 741.62 2870.00 1301.81 34.80 3.23 43.90 4.08 69.04 6.41 78.51 7.29

SHPX-9AC6-HW 994.00 450.87 1670.00 757.50 1444.00 654.99 2795.00 1267.79 36.89 3.43 46.68 4.34 75.39 7.00 85.61 7.95

SHPX-9AC-HW 929.00 421.39 1585.00 718.94 1379.00 625.50 2710.00 1229.24 35.44 3.29 45.89 4.26 73.98 6.87 84.84 7.88

SHPX-9BC-HW 1375.00 623.69 2095.00 950.28 1825.00 827.81 3220.00 1460.57 38.90 3.61 49.06 4.56 77.42 7.19 88.00 8.18

SHPX-10AC6-HW 1093.00 495.78 1846.00 837.33 1593.00 722.57 3096.00 1404.32 40.57 3.77 51.41 4.78 83.37 7.75 94.67 8.80

SHPX-10AC-HW 1028.00 466.29 1756.00 796.51 1528.00 693.09 3006.00 1363.50 39.13 3.64 50.64 4.70 81.94 7.61 93.90 8.72

SHPX-10BC-HW 1515.00 687.19 2305.00 1045.53 2015.00 913.99 3555.00 1612.52 42.55 3.95 53.96 5.01 85.35 7.93 97.23 9.03

SHPX-11AC6-HW 1192.00 540.68 2022.00 917.16 1742.00 790.16 3397.00 1540.85 44.25 4.11 56.14 5.22 91.35 8.49 103.73 9.64

SHPX-11AC-HW 1127.00 511.20 1927.00 874.07 1677.00 760.67 3302.00 1497.76 42.82 3.98 55.39 5.15 89.90 8.35 102.96 9.57

SHPX-11BC-HW 1655.00 750.70 2515.00 1140.78 2205.00 1000.17 3890.00 1764.47 46.20 4.29 58.86 5.47 93.28 8.67 106.46 9.89

SHPX-12AC6-HW 1291.00 585.59 2237.00 1014.69 1891.00 857.74 3693.00 1675.12 47.96 4.46 60.90 5.66 99.33 9.23 112.82 10.48

SHPX-12AC-HW 1226.00 556.10 2142.00 971.59 1826.00 828.26 3598.00 1632.03 46.53 4.32 60.13 5.59 97.89 9.09 112.04 10.41

SHPX-12BC-HW 1795.00 814.20 2740.00 1242.84 2395.00 1086.35 4240.00 1923.23 50.30 4.67 64.02 5.95 101.66 9.44 115.94 10.77Notes: (1) Antenna weight and wind load are approximate values for a typical structure assuming no top load. Final design loads will vary for specific projects and should be verified by an ERI representative. (2) Wind loads are calculated in accordance with the ANSI/TIA/EIA 222-F standard. Weight and effective wind area (CaAc) includes antenna, inner transmission feed and typical support mast and mounting brackets with no ice.





Type Number

Weight CaAa



Antenna with radome



MPX-1E 75.00 34.02 127.00 57.61 119.00 53.98 210.00 95.25 4.18 0.39 5.46 0.51 6.73 0.63 8.14 0.76

MPX-2C 186.00 84.37 307.00 139.25 274.00 124.28 476.00 215.91 10.11 0.94 13.78 1.28 15.21 1.41 19.14 1.78

MPX-2E 156.00 70.76 260.00 117.93 244.00 110.68 426.00 193.23 8.97 0.83 12.01 1.12 14.07 1.31 17.37 1.61

MPX-3C 267.00 121.11 440.00 199.58 399.00 180.98 692.00 313.89 14.89 1.38 20.33 1.89 22.54 2.09 28.37 2.64

MPX-3E 237.00 107.50 393.00 178.26 369.00 167.38 642.00 291.21 13.75 1.28 18.56 1.72 21.40 1.99 26.60 2.47

MPX-4C 348.00 157.85 573.00 259.91 524.00 237.68 908.00 411.86 19.68 1.83 26.88 2.50 29.87 2.78 37.60 3.49

MPX-4E 318.00 144.24 526.00 238.59 494.00 224.07 858.00 389.18 18.54 1.72 25.11 2.33 28.73 2.67 35.83 3.33

MPX-5C 429.00 194.59 706.00 320.24 649.00 294.38 1124.00 509.84 24.46 2.27 33.43 3.11 37.20 3.46 46.83 4.35

MPX-5E 399.00 180.98 659.00 298.92 619.00 280.77 1074.00 487.16 23.32 2.17 31.66 2.94 36.06 3.35 45.06 4.19

MPX-6C 510.00 231.33 839.00 380.56 774.00 351.08 1340.00 607.81 29.25 2.72 39.99 3.72 44.54 4.14 56.07 5.21

MPX-7C 561.00 254.47 925.00 419.57 869.00 394.17 1506.00 683.11 32.89 3.06 44.76 4.16 50.73 4.71 63.52 5.90

MPX-8C 672.00 304.81 1105.00 501.22 1024.00 464.48 1772.00 803.77 38.82 3.61 53.09 4.93 59.20 5.50 74.53 6.92

MPX-9C 723.00 327.95 1191.00 540.23 1119.00 507.57 1938.00 879.06 42.46 3.94 57.86 5.38 65.39 6.07 81.98 7.62

MPX-10C 834.00 378.30 1371.00 621.88 1274.00 577.88 2204.00 999.72 48.39 4.50 66.19 6.15 73.87 6.86 92.99 8.64

MPX-11C 885.00 401.43 1457.00 660.88 1369.00 620.97 2370.00 1075.01 52.03 4.83 70.96 6.59 80.06 7.44 100.44 9.33

MPX-12C 996.00 451.78 1637.00 742.53 1524.00 691.27 2636.00 1195.67 57.96 5.38 79.29 7.37 88.53 8.22 111.45 10.35

MPX-2C-HW 172.00 78.02 285.00 129.27 260.00 117.93 454.00 205.93 8.55 0.79 11.72 1.09 13.64 1.27 17.08 1.59

MPX-2E-HW 142.00 64.41 238.00 107.95 230.00 104.33 404.00 183.25 7.37 0.68 9.73 0.90 12.47 1.16 15.09 1.40

MPX-3C-HW 239.00 108.41 396.00 179.62 371.00 168.28 648.00 293.93 11.74 1.09 15.99 1.49 19.37 1.80 24.03 2.23

MPX-3E-HW 209.00 94.80 349.00 158.30 341.00 154.67 598.00 271.25 10.56 0.98 14.00 1.30 18.20 1.69 22.04 2.05

MPX-4C-HW 306.00 138.80 507.00 229.97 482.00 218.63 842.00 381.92 14.92 1.39 20.26 1.88 25.11 2.33 30.98 2.88

MPX-4E-HW 276.00 125.19 460.00 208.65 452.00 205.02 792.00 359.25 13.74 1.28 18.27 1.70 23.93 2.22 28.99 2.69

MPX-5C-HW 373.00 169.19 618.00 280.32 593.00 268.98 1036.00 469.92 18.11 1.68 24.53 2.28 30.85 2.87 37.93 3.52

MPX-5E-HW 343.00 155.58 571.00 259.00 563.00 255.37 986.00 447.24 16.93 1.57 22.54 2.09 29.67 2.76 35.94 3.34

MPX-6C-HW 440.00 199.58 729.00 330.67 704.00 319.33 1230.00 557.92 21.29 1.98 28.80 2.68 36.58 3.40 44.88 4.17

MPX-7C-HW 507.00 229.97 840.00 381.02 815.00 369.68 1424.00 645.92 24.47 2.27 33.07 3.07 42.31 3.93 51.83 4.82

MPX-8C-HW 574.00 260.36 951.00 431.37 926.00 420.03 1618.00 733.91 27.66 2.57 37.34 3.47 48.05 4.46 58.78 5.46

MPX-9C-HW 641.00 290.75 1062.00 481.72 1037.00 470.38 1812.00 821.91 30.85 2.87 41.61 3.87 53.79 5.00 65.73 6.11

MPX-10C-HW 708.00 321.14 1173.00 532.06 1148.00 520.72 2006.00 909.91 34.04 3.16 45.88 4.26 59.52 5.53 72.68 6.75

MPX-11C-HW 775.00 351.53 1284.00 582.41 1259.00 571.07 2200.00 997.90 37.23 3.46 50.15 4.66 65.25 6.06 79.63 7.40

MPX-12C-HW 842.00 381.92 1395.00 632.76 1370.00 621.42 2394.00 1085.90 40.41 3.75 54.42 5.06 70.98 6.59 86.58 8.04Notes: (1) Antenna weight and wind load are approximate values for a typical structure assuming no top load. Final design loads will vary for specific projects and should be verified by an ERI representative. (2) Wind loads are calculated in accordance with the ANSI/TIA/EIA 222-F standard. Weight and effective wind area (CaAc) includes antenna, inner transmission feed and typical support mast and mounting brackets with no ice.

MPX Model - Medium Power




Type Number

Weight CaAa



Antenna with radome



LPX-1E 62.00 28.12 102.00 46.27 106.00 48.08 176.00 79.83 3.08 0.29 4.59 0.43 5.61 0.52 7.24 0.67

LPX-2C 163.00 73.94 256.00 116.12 251.00 113.85 406.00 184.16 8.40 0.78 12.00 1.11 13.45 1.25 17.30 1.61

LPX-2E 124.00 56.25 204.00 92.53 212.00 96.16 352.00 159.66 6.38 0.59 9.60 0.89 11.43 1.06 14.90 1.38

LPX-3C 225.00 102.06 358.00 162.39 357.00 161.93 582.00 263.99 11.69 1.09 17.02 1.58 19.26 1.79 24.96 2.32

LPX-3E 186.00 84.37 306.00 138.80 318.00 144.24 528.00 239.50 9.67 0.90 14.62 1.36 17.24 1.60 22.56 2.10

LPX-4C 287.00 130.18 460.00 208.65 463.00 210.01 758.00 343.82 14.99 1.39 22.03 2.05 25.08 2.33 32.62 3.03

LPX-4E 248.00 112.49 408.00 185.07 424.00 192.32 704.00 319.33 12.97 1.20 19.64 1.82 23.06 2.14 30.23 2.81

LPX-5C 349.00 158.30 562.00 254.92 569.00 258.09 934.00 423.66 18.29 1.70 27.04 2.51 30.90 2.87 40.28 3.74

LPX-5E 310.00 140.61 510.00 231.33 530.00 240.40 880.00 399.16 16.27 1.51 24.65 2.29 28.88 2.68 37.89 3.52

LPX-6C 411.00 186.43 664.00 301.19 675.00 306.17 1110.00 503.49 21.58 2.00 32.06 2.98 36.72 3.41 47.95 4.45

LPX-7C 473.00 214.55 766.00 347.45 781.00 354.26 1286.00 583.32 24.87 2.31 37.08 3.44 42.54 3.95 55.62 5.17

LPX-8C 535.00 242.67 868.00 393.72 887.00 402.34 1462.00 663.15 28.17 2.62 42.09 3.91 48.36 4.49 63.27 5.88

LPX-9C 101.00 45.81 154.00 69.85 145.00 65.77 230.00 104.33 5.31 0.49 7.41 0.69 7.84 0.73 10.05 0.93

LPX-10C 659.00 298.92 1072.00 486.25 1099.00 498.50 1814.00 822.82 34.77 3.23 52.12 4.84 60.00 5.57 78.60 7.30

LPX-11C 225.00 102.06 358.00 162.39 357.00 161.93 582.00 263.99 11.91 1.11 17.44 1.62 19.48 1.81 25.38 2.36

LPX-12C 783.00 355.16 1276.00 578.78 1311.00 594.66 2166.00 982.48 41.36 3.84 62.15 5.77 71.64 6.66 93.93 8.73

LPX-2C-HW 157.00 71.21 247.00 112.04 245.00 111.13 397.00 180.08 7.59 0.71 10.50 0.98 12.63 1.17 15.79 1.47

LPX-2E-HW 118.00 53.52 195.00 88.45 206.00 93.44 343.00 155.58 5.62 0.52 8.32 0.77 10.67 0.99 13.62 1.27

LPX-3C-HW 213.00 96.62 340.00 154.22 345.00 156.49 564.00 255.83 10.12 0.94 14.23 1.32 17.69 1.64 22.17 2.06

LPX-3E-HW 174.00 78.93 288.00 130.63 306.00 138.80 510.00 231.33 8.15 0.76 12.05 1.12 15.73 1.46 20.00 1.86

LPX-4C-HW 269.00 122.02 433.00 196.41 445.00 201.85 731.00 331.58 12.66 1.18 17.96 1.67 22.75 2.11 28.55 2.65

LPX-4E-HW 230.00 104.33 381.00 172.82 406.00 184.16 677.00 307.08 10.69 0.99 15.79 1.47 20.78 1.93 26.38 2.45

LPX-5C-HW 325.00 147.42 526.00 238.59 545.00 247.21 898.00 407.33 15.20 1.41 21.69 2.02 27.81 2.58 34.93 3.25

LPX-5E-HW 286.00 129.73 474.00 215.00 506.00 229.52 844.00 382.83 13.23 1.23 19.52 1.81 25.84 2.40 32.76 3.04

LPX-6C-HW 381.00 172.82 619.00 280.77 645.00 292.57 1065.00 483.08 17.73 1.65 25.43 2.36 32.87 3.05 41.32 3.84

LPX-7C-HW 437.00 198.22 712.00 322.96 745.00 337.93 1232.00 558.83 20.26 1.88 29.17 2.71 37.93 3.52 47.71 4.43

LPX-8C-HW 493.00 223.62 805.00 365.14 845.00 383.29 1399.00 634.58 22.80 2.12 32.89 3.06 42.99 3.99 54.08 5.02

LPX-9C-HW 549.00 249.02 898.00 407.33 945.00 428.64 1566.00 710.33 25.34 2.35 36.61 3.40 48.05 4.46 60.45 5.62

LPX-10C-HW 605.00 274.42 991.00 449.51 1045.00 474.00 1733.00 786.08 27.88 2.59 40.36 3.75 53.11 4.93 66.84 6.21

LPX-11C-HW 661.00 299.82 1084.00 491.69 1145.00 519.36 1900.00 861.83 30.42 2.83 44.11 4.10 58.17 5.40 73.23 6.80

LPX-12C-HW 717.00 325.23 1186.00 537.96 1245.00 564.72 2067.00 937.58 32.95 3.06 47.82 4.44 63.23 5.87 79.60 7.40Notes: (1) Antenna weight and wind load are approximate values for a typical structure assuming no top load. Final design loads will vary for specific projects and should be verified by an ERI representative. (2) Wind loads are calculated in accordance with the ANSI/TIA/EIA 222-F standard. Weight and effective wind area (CaAc) includes antenna, inner transmission feed and typical support mast and mounting brackets with no ice.

LPX Model - Low Power



Mounting Notes

The base price of ERI FM antennas include brackets for mounting on a tower leg or pole, up to 15-inches in diameter, or for face mounting on a uniform cross section tower section up to 42-inch face. Optional, standard fiberglass and steel anti-rotation brackets are available for uniform cross section tower faces up to 42-inches, center to center. For uniform tower faces greater than 42-inches steel anti-rotation brackets are generally used. Fiberglass anti-rotation brackets for face sizes larger than 42-inches may be available as a special order item. Please contact ERI with those requirements. Standard FM antenna mounting brackets and anti-rotation brackets assume that the tower face is unobstructed. If conduits, transmission lines, or other appurtenances are mounted on the tower face(s) they could interfere with standard bracket designs and may require an optional, extra cost, brackets to accommodate the obstruction. Contact ERI with details for further information. Brackets for mounting on tapered tower legs are available at additional cost. Contact ERI with tower details. Anti-rotation brackets (one per bay) required for leg mounting if leg O.D. is:

• LPX, LP, 300, and 350 Series Antennas - 2-inches (51 mm) leg size or less

• SHPX, SHP, SHP-H, MPX, and MP Series Antennas - 3-inches (76 mm) leg size or less

• Radomed Antennas - 5-inches (127 mm) leg size or less

Utilize the ERI AdvantageCombine an ERI antenna with an ERI Mounting Structure, Pattern Measurement and Installation. Assure yourself of the best antenna/tower interaction. ERI’s Pattern Measurement service will provide the crucial answers concerning the relationship between the antenna mounting orientation and antenna pattern.

ERI Mounting Sections are designed to achieve optimum antenna performance while reducing weight and wind loads. Only ERI can offer you an antenna/tower/installation package that will achieve your highest expectations in a demanding FM market. Contact Electronics Research for complete electrical and mechanical specifications.



Ordering Information

Type Number Definitiona - b c d e - f - g - h

a Model: SHPX, LPX, MPX

b Number of Bays

c Interbay Line Size: A = 3 1/8 inch, B = 4 1/8 inch, C = 6 1/8 inch

d Input Feed Configuration: E = End Fed, C = Center fed for even number of bays, off center fed for odd number of bays

e RF Input Size: Blank = 3 1/8 inch, 6 = 6 1/8 inch

f Design Note 1: Blank = Omnidirectional, DA = Directional Azimuth Pattern

g Design Note 2: Blank = Full wave length bay to bay spacing, HW = Half wave length bay to bay spacing

h Design Note 3: Blank = Standard product, SP = Special Design

Example: SHPX-4AC-DA-HW

Description: ERI Model SHPX ROTOTILLER FM Antenna, four bay, 4 1/8 inch interbay line, center fed, directional azimuth pattern, half wave length bay to bay spacing.

Options*

• Anti-rotation brackets• Quarter wave stub - Included with SHPX, MPX, and LPX

antennas• Beam tilt (center fed antennas only)• First null fill (center fed antennas only)• Second null fill (center fed antennas only); Second null

fill not available for LPX antennas• Beam tilt and first null fill (center fed antennas only)• Radomes• Deicers (600w/220v)• Stem heaters (300w/220v)• Export packing* Options available at additional cost.


Around the World, Across the Spectrum,Your Single Source For Broadcast Solutions

About Electronics Research, Inc.Founded in 1943, Electronics Research, Inc. delivers high quality, innovative, integrated solutions to broadcasters across the U.S. and around the world. Our dedicated staff of engineers, designers, fabricators, and project managers take pride in contributing to your success by providing AM, FM, VHF, UHF, BRS-EBS, and Mobile Media broadcast systems including the industry’s best antenna, transmission line, filter/combiner, and tower and structural support systems. In addition to manufacturing the full range of broadcast system components and installation accessories, ERI offers a suite of engineering and field services needed to plan, install, optimize, and maintain your broadcast facility. We are your single source for broadcast solutions.

Broadcast Antenna Systems• ROTOTILLER® FM Antenna

• LYNX™ Dual Input Antenna for FM-IBOC

• 1105 Circularly Polarized FM Antenna

• 100A Series Low Power Circularly Polarized FM Antenna

• FM Low Power Horizontally Polarized Educational FM Antenna

• P300/P350 Series Vertically Polarized FM Antenna

• 1180 and 1090 Series Broadband Panel FM Radio Antenna

• SLIMWING™ Batwing VHF Television Antenna

• CRUCIS™ Crossed Dipole VHF Television Antenna

• STINGRAY™ Broadband Television Panel Antenna

• TRASAR® High Power Traveling Wave Television Antenna

• AGW Quick-Deploy Emergency UHF Television Antenna

• ALP Low and Medium Power UHF Television Antenna

• AL PLUS Low and Medium Power UHF Television Antenna

• AL Series Low Power UHF Television Antenna

• HMD BRS-EBS Antenna

• SHADOWMASTER® Shadow-Filling BRS-EBS Antenna

Transmission Line Systems• MACXLine® Rigid Transmission Line with Bellows• HELIAX® Air- and Foam-dielectric Coaxial Cable• HELIAX® Standard Elliptical Waveguide• GUIDELine® Circular Waveguide• Standard Rectangular Waveguide• Dehydrators and Pressurization Equipment

Filter and Combining Systems• FM Radio Filter and Combining Systems

• UHF and VHF Television Filter and Combining Systems

• DAB Filter and Combining Systems

• Mobile Media Filter and Combining Systems

• RF Components

• System Monitoring and Protection Components

Structural Support Systems• Guyed Towers

• Self-Supporting Towers

• Roof-top Antenna Support Structures

• Specialty Structures and Custom Antenna Supports

RF and Structural System Services• RF Field and Engineering Services

• Installation and Structural Engineering Services

Electronics Research, Inc.7777 Gardner RoadChandler, Indiana 47610-9219USA

877 ERI-LINE (toll-free: North America)www.eriinc.com (web)+1 812 925-6000 (international)+1 812 925-4030 (fax)

All designs, specifications, and availabilities of products and services presented in this publication are subject to change without notice.

Antennas Transmission Line Towers Filters/Combiners Broadcast Services

11/13/2014 ERI - SHPX-12AC-HW

http://www.eriinc.com/Catalog/Antennas/FM-Antennas/ROTOTILLER-X-Series/SHPX-12AC-HW.aspx 1/1

Catalog > Antennas > FM Antennas > ROTOTILLER X Series > SHPX-12AC-HW

ROTOTILLER ® X Series Circularly Polarized FM Antenna

Type Number: SHPX-12AC-HW

ROTOTILLER X Series SHPX Model Super High Power Circularly Polarized FM Antenna


Number of Bays: 12

Power Gain: 3.7320 numeric | 5.7194 dB

Input Type: 3 1/8 inch 50 Ohm EIA Female

Feed Configuration: Center

Input Power Rating: 39 kW

Bay to Bay Spacing: 0.5 Wave Length


Weight, Antenna only: 1226 lbm | 556.10 kg

Weight, Antenna with radome: 1826 lbm | 828.26 kg

Weight, Antenn with half inch of ice: 2142 lbm | 971.59 kg

Weight, Antenna with radome and half inch of ice: 3598 lbm | 1,632.03 kg

CaAa, Antenna only: 46.53 ft2 | 4.32 m2

CaAa, Antenna with radome: 97.89 ft2 | 9.09 m2

CaAa, Antenna with half inch of ice: 60.13 ft2 | 5.59 m2

CaAa, Antenna with radome and half inch of ice: 112.04 ft2 | 10.41 m2

Mechanical Specification Notes

(1) All loads calculated in accordance with the ANSI/TIA-222 standard. (2) Prov ided ef f ectiv e wind areas, CaAa, do NOT include potential wind shielding/interf erence due to

the interaction with the supporting structure (i.e. does not include Ka f actor). (3) Listed antenna weights and ef f ectiv e wind areas assume 98 MHz and include the antenna

radiating elements, f eed harnessing, and standard leg mounting brackets. Special mounting bracket loads f or f ace-mounted and/or pole standof f mounted sy stems are NOT

included. Final design loads will v ary f or specif ic projects and should be v erif ied by an ERI representativ e when precise loading is required.

All designs, specif ications, and av ailabilities of products and serv ices presented in this publication are subject to change without notice.

Pages on this site may require Adobe Reader. You can download this f ree sof tware here.

Copy right © 2014 Electronics Research, Inc. All rights reserv ed.

11/13/2014 Mail - KBAQ Phoenix

https://mail.google.com/mail/u/0/?ui=2&ik=242e6b96a9&view=pt&cat=A%20Tower&search=cat&msg=14977db22820a4f4&siml=14977db22820a4f4

Ralph Hogan <[email protected]>

KBAQ Phoenix

Shawn Knotts <[email protected]> Mon, Nov 3, 2014 at 3:51 PM

ERI MP - 10AC - DA - HW - SP - FM Antenna

System Length - 52.011 ftBay Spacing - 65.698 inches

EFFECTIVE PROJECTED AREA(ft^2) (EPA)

NORMAL(ft^2) TRANSVERSE(ft^2) WEIGHT(lbs.)

No Ice 62.7 64.4 1,020 0.5 in Ice 91.9 93.9 1,860 1.0 in Ice 118.8 121.5 2,9702.0 in Ice 177.5 181.1 6,4204.0 in Ice 310.4 318.9 17,500

Shawn Knotts

Western Region Account Manager

Electronics Research, Inc.

(812) 760-5581

[email protected] 5:02:26 PMSubject: KBAQ Phoenix

Electronics Research, Inc. 7777 Gardner Rd. Chandler, In 47610 Phone (812) 925-6000 Fax (812) 925-4030 http://www.eriinc.com/

Directional Antenna System

for KBAQ, Phoenix, Arizona

July 2, 2009

Electronics Research Inc. is providing a custom fabricated antenna system that is specially designed to meet the FCC requirements and the general needs of radio station KBAQ. The antenna is the ERI model MP-10AC-HW-SP configuration. The circular polarized system consists of 10 half-wavelength spaced bays using one driven circular polarized radiating element per bay, two horizontal parasitic elements at bay level and four vertical parasitic elements per bay. The antenna was mounted on the North 1 degrees East tower leg with bracketry to provide an antenna orientation of North 1 degrees East. The antenna was tested on a 27.5" face tower, which is the structure the station plans to use to support the array. All tests were performed on a frequency of 89.5 megahertz, which is the center of the FM broadcast channel assigned to KBAQ. The system will included –0.585 degrees of beam tilt. Pattern measurements were made on a sixty-acre antenna pattern range that is owned and operated by Electronics Research, Inc. The tests were performed under the direction of Thomas B. Silliman, president of Electronics Research, Inc. Mr. Silliman has the Bachelor of Electrical Engineering and the Master of Electrical Engineering degrees from Cornell University and is a registered professional engineer in the states of Indiana, Maryland and Minnesota.

Directional Antenna System Proposed For

KBAQ, Phoenix, Arizona

(Continued)

2

DESCRIPTION OF THE TEST PROCEDURE The test antenna consisted of two bay levels of the circular polarized system with the associated horizontal and vertical parasitic elements. The elements and brackets that were used in this test are electrically equivalent to those that will be supplied with the antenna. A section of 3 1/8 inch o.d. rigid coaxial line was used to feed the test antenna, and a section of 3 1/8 inch o.d. rigid outer conductor only was attached above the test antenna. The lines were properly grounded during all tests. The power distribution and phase relationship to the antenna elements was adjusted in order to achieve the directional radiation patterns for both horizontal and vertical polarization components. The proof-of-performance was accomplished using a 27.5" face tower with identical dimension and configuration including all braces, ladders, conduits, coaxial lines and other appurtenances that are included in the actual aperture at which the antenna will be installed. The structure was erected vertically on a turntable mounted on a non-metallic building with the antenna centered vertically on the structure, making the center of radiation of the test approximately 30 feet above ground. The turntable is equipped with a motor drive and a US Digital angle position indicator. The resolution of this angle position indicator is one-hundredth of a degree. The antenna under test was operated in the transmitting mode and fed from a HP8657D signal generator. The frequency of the signal source was set at 89.5 MHz and was constantly monitored by a Rohde & Schwarz ESVD measuring receiver.



(Continued)

3

A broadband horizontal and vertical dipole system, located approximately 628 feet from the test antenna, was used to receive the emitted test signals. The dipole system was mounted at the same height above terrain as the center of the antenna under test. The signals received by the dipole system were fed to the test building by way of two buried Heliax cables to a Rohde & Schwarz measuring receiver. This data was interfaced to a laser jet printer by means of a computer system. Relative field strength was plotted as a function of azimuth. The measurements were performed by rotating the test antenna in a counter-clockwise direction and plotting the received signal on polar co-ordinated graph paper in a clockwise direction. Both horizontal and vertical components were recorded separately. CONCLUSIONS The circular polarized system consists of 10 half-wavelength spaced bays using one driven circular polarized radiating element per bay, two horizontal parasitic elements at bay level and four vertical parasitic elements per bay. The power distribution and phase relationship will be fixed when antenna is manufactured. Proper maintenance of the elements should be all that is required to maintain the pattern in adjustment. The MP-10AC-HW-SP array is to be mounted on the North 1 degrees East tower leg of the 27.5" face tower at a bearing of North 1 degrees East. Blue prints provided with the antenna will show the proper antenna orientation alignment. The antenna alignment procedure should be directed by a licensed surveyor as prescribed by the FCC. Figure #1 represents the maximum value of either the horizontal or vertical component at any azimuth. The measured horizontal plane relative field pattern, for both the horizontal and vertical polarization components, is shown on Figure #2 attached. The actual measured pattern does not exceed the authorized FCC composite pattern at any azimuth. A calculated vertical plane relative field pattern is shown on Figure #3 attached. The power in the maximum will reach 30 kilowatts (14.771 dBk). The power at North 110-170 degrees East does not exceed 13.147 kilowatts (11.188 dBk).



(Continued)

4

The power at North 190-200 degrees East does not exceed 14.995 kilowatts (11.759 dBk). The power at North 220-240 degrees East does not exceed 15.038 kilowatts (11.772 dBk). The RMS of the vertically polarized horizontal plane component does not exceed the RMS of the horizontally polarized horizontal plane component. The composite horizontal and vertical maximum relative field pattern obtained from the measured data as shown on Figure #1 has an RMS that is greater that 85% of the filed composite pattern. The clear vertical length of the structure required to support the antenna is 69 feet 3 inches. The directional antenna should not be mounted on the top of an antenna tower that includes a top-mounted platform larger than the cross-sectional area of the tower in the horizontal plane. No obstructions other than those that are specified by the blue prints supplied with the antenna are to be mounted within 75 ft. horizontally of the system. The vertical distance to the nearest obstruction should be a minimum of 10 ft. from the directional antenna. Metallic guy wires should be a minimum distance of forty feet horizontally from the antenna. ELECTRONICS RESEARCH, INC.

The Microsoft Word document on file electronically at Electronic Research, Inc. governs the specifications, scope, and configuration of the product described. All other representations whether verbal, printed, or electronic are subordinate to the master copy of this document on file at ERI.

® Horizontal Plane Relative Field Pattern


1.00

0.80

0.60

0.40

0.20

FIGURE NO: 1 STATION: KBAQ LOCATION: PHOENIX, AZ. ANTENNA: MP-10AC-DA-HW-SP STRUCTURE: 27.5'' FACE TOWER

DATE: 7/2/2009 FREQUENCY: 89.5 MHZ ORIENTATION: 1° TRUE MOUNTING: 16" ELL BAYS TESTED: TWO

COMMENTS: COMPOSITE PATTERN: THIS PATTERN SHOWS THE MAXIMUM OF EITHER THE H OR V AZIMUTH VALUES. THIS

PATTERN IS GREATER THAT 90% OF THE FCC FILED COMPOSITE PATTERN BPED-20060227AHT.

Measured Composite:

RMS: 0.821 Maximum: 1.000 @ 3° True Minimum: 0.537 @ 146° True

FCC COMPOSITE:

RMS: 0.875 MAXIMUM : 1.000 @ 0° TRUE MINIMUM : 0.662 @ 110° TRUE

® Horizontal Plane Relative Field List Electronics Research, Inc. 7777 Gardner Rd. Chandler, In 47610 Phone (812) 925-6000 Fax (812) 925-4030 http://www.eriinc.com/

Envelope Envelope Angle Field kW dBk

Polarization Angle

Field kW dBk

Polarization

0º 0.998 29.87 14.75 Vertical 180º 0.580 10.10 10.04 Vertical 5º 1.000 29.97 14.77 Vertical 185º 0.587 10.33 10.14 Vertical

10º 0.995 29.72 14.73 Vertical 190º 0.592 10.51 10.21 Vertical 15º 0.987 29.23 14.66 Vertical 195º 0.595 10.61 10.26 Vertical 20º 0.975 28.50 14.55 Vertical 200º 0.596 10.66 10.28 Vertical 25º 0.958 27.54 14.40 Vertical 205º 0.598 10.74 10.31 Vertical 30º 0.938 26.39 14.22 Vertical 210º 0.604 10.94 10.39 Vertical 35º 0.921 25.42 14.05 Vertical 215º 0.613 11.27 10.52 Vertical 40º 0.907 24.70 13.93 Vertical 220º 0.625 11.72 10.69 Vertical 45º 0.910 24.85 13.95 Horizontal 225º 0.638 12.23 10.87 Vertical 50º 0.922 25.52 14.07 Horizontal 230º 0.656 12.90 11.11 Vertical 55º 0.939 26.44 14.22 Horizontal 235º 0.679 13.83 11.41 Vertical 60º 0.955 27.35 14.37 Horizontal 240º 0.707 14.98 11.76 Vertical 65º 0.966 28.00 14.47 Horizontal 245º 0.740 16.44 12.16 Vertical 70º 0.970 28.21 14.50 Horizontal 250º 0.783 18.40 12.65 Vertical 75º 0.962 27.77 14.44 Horizontal 255º 0.829 20.60 13.14 Vertical 80º 0.941 26.56 14.24 Horizontal 260º 0.865 22.46 13.52 Vertical 85º 0.905 24.59 13.91 Horizontal 265º 0.891 23.83 13.77 Vertical 90º 0.855 21.93 13.41 Horizontal 270º 0.906 24.64 13.92 Vertical 95º 0.794 18.93 12.77 Horizontal 275º 0.908 24.75 13.94 Vertical

100º 0.741 16.47 12.17 Vertical 280º 0.912 24.93 13.97 Horizontal 105º 0.695 14.48 11.61 Vertical 285º 0.928 25.83 14.12 Horizontal 110º 0.657 12.95 11.12 Vertical 290º 0.941 26.58 14.25 Horizontal 115º 0.626 11.74 10.70 Vertical 295º 0.952 27.18 14.34 Horizontal 120º 0.599 10.76 10.32 Vertical 300º 0.961 27.68 14.42 Horizontal 125º 0.577 9.99 10.00 Vertical 305º 0.968 28.10 14.49 Horizontal 130º 0.560 9.41 9.74 Vertical 310º 0.974 28.46 14.54 Horizontal 135º 0.548 9.00 9.54 Vertical 315º 0.980 28.83 14.60 Horizontal 140º 0.540 8.76 9.42 Vertical 320º 0.986 29.17 14.65 Horizontal 145º 0.537 8.66 9.38 Vertical 325º 0.991 29.47 14.69 Horizontal 150º 0.538 8.69 9.39 Vertical 330º 0.995 29.70 14.73 Horizontal 155º 0.541 8.79 9.44 Vertical 335º 0.998 29.88 14.75 Horizontal 160º 0.547 8.99 9.54 Horizontal 340º 1.000 29.99 14.77 Horizontal 165º 0.555 9.25 9.66 Horizontal 345º 0.999 29.94 14.76 Horizontal 170º 0.562 9.47 9.76 Horizontal 350º 0.995 29.70 14.73 Horizontal 175º 0.572 9.80 9.91 Vertical 355º 0.988 29.29 14.67 Horizontal

Station: KBAQ Location: Phoenix, AZ. Frequency: 89.5 MHz

Antenna: MP-10AC-DA-HW-SP Orientation: 1° True Tower: 27.5'' Face tower

Figure: 1 Date: 7/2/2009 Reference: kbaq1m.fig

Polarization: Maximum Field: Minimum Field: RMS: Maximum ERP: Maximum Power Gain: Horizontal Plane Gain:

Envelope 1.000 @ 3° True 0.537 @ 146° True 0.821 30.000 kW 4.676 (6.699 dB) 4.717 (6.737 dB)

Total Input Power: 6.415 kW

® Horizontal Plane Relative Field Pattern


FIGURE NO: STATION: LOCATION: ANTENNA: STRUCTURE:

DATE: FREQUENCY: ORIENTATION: ° TRUE MOUNTING:

Horizontal

RMS: Maximum: Minimum:

VERTICAL

RMS: MAXIMUM : MINIMUM :

1.00

0.80

0.60

0.40

0.20

FIGURE NO: 1 STATION: KBAQ LOCATION: PHOENIX, AZ. ANTENNA: MP-10AC-DA-HW-SP STRUCTURE: 27.5'' FACE TOWER

DATE: 7/2/2009 FREQUENCY: 89.5 MHZ ORIENTATION: 1° TRUE MOUNTING: STANDARD BAYS TESTED: TWO

COMMENTS: MEASURED PATTERNS OF THE HORIZONTAL AND VERTICAL COMPONENTS.

Horizontal

RMS: 0.801 Maximum: 1.000 @ 341° True Minimum: 0.524 @ 141° True

VERTICAL

RMS: 0.784 MAXIMUM : 1.000 @ 3° TRUE MINIMUM : 0.537 @ 146° TRUE

® Horizontal Plane Relative Field List Electronics Research, Inc. 7777 Gardner Rd. Chandler, In 47610 Phone (812) 925-6000 Fax (812) 925-4030 http://www.eriinc.com/

Horizontal Vertical Horizontal Vertical Angle Field kW dBk Field kW dBk Angle

Field kW dBk Field kW dBk 0º 0.979 28.74 14.59 0.998 29.87 14.75 180º 0.568 9.69 9.86 0.580 10.10 10.04 5º 0.965 27.93 14.46 1.000 29.97 14.77 185º 0.569 9.70 9.87 0.587 10.33 10.14

10º 0.950 27.08 14.33 0.995 29.72 14.73 190º 0.567 9.65 9.84 0.592 10.51 10.21 15º 0.936 26.28 14.20 0.987 29.23 14.66 195º 0.563 9.50 9.78 0.595 10.61 10.26 20º 0.924 25.60 14.08 0.975 28.50 14.55 200º 0.556 9.28 9.67 0.596 10.66 10.28 25º 0.914 25.07 13.99 0.958 27.54 14.40 205º 0.548 9.03 9.55 0.598 10.74 10.31 30º 0.907 24.70 13.93 0.938 26.39 14.22 210º 0.542 8.80 9.44 0.604 10.94 10.39 35º 0.904 24.50 13.89 0.921 25.42 14.05 215º 0.538 8.67 9.38 0.613 11.27 10.52 40º 0.904 24.52 13.90 0.907 24.70 13.93 220º 0.539 8.72 9.41 0.625 11.72 10.69 45º 0.910 24.85 13.95 0.898 24.20 13.84 225º 0.548 9.01 9.55 0.638 12.23 10.87 50º 0.922 25.52 14.07 0.893 23.93 13.79 230º 0.565 9.59 9.82 0.656 12.90 11.11 55º 0.939 26.44 14.22 0.892 23.89 13.78 235º 0.592 10.51 10.22 0.679 13.83 11.41 60º 0.955 27.35 14.37 0.894 23.98 13.80 240º 0.627 11.81 10.72 0.707 14.98 11.76 65º 0.966 28.00 14.47 0.897 24.15 13.83 245º 0.669 13.42 11.28 0.740 16.44 12.16 70º 0.970 28.21 14.50 0.900 24.32 13.86 250º 0.713 15.26 11.84 0.783 18.40 12.65 75º 0.962 27.77 14.44 0.895 24.05 13.81 255º 0.758 17.22 12.36 0.829 20.60 13.14 80º 0.941 26.56 14.24 0.882 23.32 13.68 260º 0.799 19.14 12.82 0.865 22.46 13.52 85º 0.905 24.59 13.91 0.859 22.15 13.45 265º 0.835 20.92 13.20 0.891 23.83 13.77 90º 0.855 21.93 13.41 0.828 20.58 13.13 270º 0.866 22.51 13.52 0.906 24.64 13.92 95º 0.794 18.93 12.77 0.789 18.65 12.71 275º 0.892 23.86 13.78 0.908 24.75 13.94

100º 0.733 16.13 12.08 0.741 16.47 12.17 280º 0.912 24.93 13.97 0.896 24.10 13.82 105º 0.678 13.81 11.40 0.695 14.48 11.61 285º 0.928 25.83 14.12 0.879 23.15 13.65 110º 0.634 12.05 10.81 0.657 12.95 11.12 290º 0.941 26.58 14.25 0.857 22.06 13.44 115º 0.600 10.79 10.33 0.626 11.74 10.70 295º 0.952 27.18 14.34 0.835 20.94 13.21 120º 0.573 9.86 9.94 0.599 10.76 10.32 300º 0.961 27.68 14.42 0.815 19.92 12.99 125º 0.553 9.17 9.62 0.577 9.99 10.00 305º 0.968 28.10 14.49 0.798 19.10 12.81 130º 0.538 8.67 9.38 0.560 9.41 9.74 310º 0.974 28.46 14.54 0.786 18.55 12.68 135º 0.528 8.36 9.22 0.548 9.00 9.54 315º 0.980 28.83 14.60 0.782 18.35 12.64 140º 0.524 8.23 9.16 0.540 8.76 9.42 320º 0.986 29.17 14.65 0.787 18.60 12.70 145º 0.525 8.28 9.18 0.537 8.66 9.38 325º 0.991 29.47 14.69 0.802 19.30 12.85 150º 0.531 8.46 9.27 0.538 8.69 9.39 330º 0.995 29.70 14.73 0.826 20.45 13.11 155º 0.539 8.71 9.40 0.541 8.79 9.44 335º 0.998 29.88 14.75 0.858 22.10 13.44 160º 0.547 8.99 9.54 0.546 8.95 9.52 340º 1.000 29.99 14.77 0.900 24.29 13.85 165º 0.555 9.25 9.66 0.553 9.17 9.63 345º 0.999 29.94 14.76 0.938 26.39 14.21 170º 0.562 9.47 9.76 0.562 9.46 9.76 350º 0.995 29.70 14.73 0.967 28.05 14.48 175º 0.566 9.61 9.83 0.572 9.80 9.91 355º 0.988 29.29 14.67 0.987 29.22 14.66

Station: KBAQ Location: Phoenix, AZ. Frequency: 89.5 MHz

Antenna: MP-10AC-DA-HW-SP Orientation: 1° True Tower: 27.5'' Face tower

Figure: 2 Date: 7/2/2009 Reference: kbaq1m.fig

Polarization: Maximum Field: Minimum Field: RMS: Maximum ERP: Maximum Power Gain: Horizontal Plane Gain:

Horizontal 1.000 @ 341° True 0.524 @ 141° True 0.801 30.000 kW 4.676 (6.699 dB) 4.717 (6.737 dB)

Vertical 1.000 @ 3° True 0.537 @ 146° True 0.784 30.000 kW 4.676 (6.699 dB) 4.717 (6.737 dB)

Total Input Power: 6.415 kW

Directional Antenna System for


(Continued)

ANTENNA SPECIFICATIONS

Antenna Type: MP-10AC-DA-HW-SP Frequency: 89.5 MHz Number of Bays: Ten

MECHANICAL SPECIFICATIONS

Mounting: Standard System length: 53 ft 5 in Aperture length required: 69 ft 3 in Orientation: 1° true Input flange to the antenna 3 1/8“ female.

ELECTRICAL SPECIFICATIONS

(For directional use)

Maximum horizontal ERP: 30.000 kW (14.771 dBk) Horizontal maximum power gain: 4.676 (6.699 dB) H Pol H Plane power gain: 4.717 (6.737 dB) Maximum vertical ERP: 30.000 kW (14.771 dBk) Vertical maximum power gain: 4.676 (6.699 dB) V Pol H Plane power gain: 4.717 (6.737 dB) Beam Tilt: -0.585° Total input power: 6.415 kW (8.072 dBk)

VHLPX3VHLPX3--6W6W 1.0 m | 3 ft ValuLine® High Performance Low Profile Antenna, dualpolarized, 5.925–7.125 GHz

General Specifications Antenna Type VHLPX ValuLine® High Performance Low Profile Antenna, dualpolarized Diameter, nominal 1.0 m | 3 ft Polarization Dual

Electrical Specifications Beamwidth, Horizontal 3.3 ° Beamwidth, Vertical 3.3 ° Cross Polarization Discrimination (XPD) 30 dB Electrical Compliance Brazil Anatel Class 2 | ETSI 302 217 Class 3 | US FCC Part 101B2 FronttoBack Ratio 60 dB Gain, Low Band 32.0 dBi Gain, Mid Band 33.0 dBi Gain, Top Band 34.0 dBi Operating Frequency Band 5.925 – 7.125 GHz Radiation Pattern Envelope Reference (RPE) 7167 Return Loss 17.7 dB VSWR 1.30

Mechanical Specifications Fine Azimuth Adjustment ±15° Fine Elevation Adjustment ±15° Mounting Pipe Diameter 115 mm | 4.5 in Net Weight 24 kg | 53 lb Side Struts, Included 0 Side Struts, Optional 1 inboard Wind Velocity Operational 200 km/h | 124 mph Wind Velocity Survival Rating 250 km/h | 155 mph

Wind Forces At Wind Velocity Survival Rating Angle a for MT Max 0 ° Axial Force (FA) 2979 N | 670 lbf Side Force (FS) 936 N | 210 lbf Twisting Moment (MT) 1184 N•m Weight with 1/2 in (12 mm) Radial Ice 46 kg | 101 lb

Product SpecificationsProduct Specifications

©©2014 CommScope, Inc. All rights reserved. All trademarks identified by 2014 CommScope, Inc. All rights reserved. All trademarks identified by ® ® or ™ are registered trademarks, respectively, of CommScope.or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: June 11, 2014All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: June 11, 2014

page 1 of 5page 1 of 5September 22, 2014September 22, 2014

Zcg with 1/2 in (12 mm) Radial Ice 220 mm | 9 in Zcg without Ice 324 mm | 13 in

Product SpecificationsProduct SpecificationsVHLPX3VHLPX3--6W6W



Wind Forces At Wind Velocity Survival Rating Image




Antenna Dimensions And Mounting Information

* Footnotes

Axial Force (FA) Maximum forces exerted on a supporting structure as a result of wind from the most critical direction for this parameter. The individual maximums specified may not occur simultaneously. All forces are referenced to the mounting pipe.

Cross Polarization Discrimination (XPD) The difference between the peak of the copolarized main beam and the maximum crosspolarized signal over an angle twice the 3 dB beamwidth of the copolarized main beam.

FronttoBack Ratio Denotes highest radiation relative to the main beam, at 180° ±40°, across the band. Production antennas do not exceed rated values by more than 2 dB unless stated otherwise.

Gain, Mid Band For a given frequency band, gain is primarily a function of antenna size. The gain of Andrew antennas is determined by either gain by comparison or by computer integration of the measured antenna patterns.

Operating Frequency Band Bands correspond with CCIR recommendations or common allocations used throughout the world. Other ranges can be accommodated on special order.

Radiation Pattern Envelope Reference (RPE) Radiation patterns determine an antenna’s ability to discriminate against unwanted signals under conditions of radio congestion. Radiation patterns




are dependent on antenna series, size, and frequency.

Return Loss The figure that indicates the proportion of radio waves incident upon the antenna that are rejected as a ratio of those that are accepted.

Side Force (FS) Maximum side force exerted on the mounting pipe as a result of wind from the most critical direction for this parameter. The individual maximums specified may not occur simultaneously. All forces are referenced to the mounting pipe.

Twisting Moment (MT) Maximum forces exerted on a supporting structure as a result of wind from the most critical direction for this parameter. The individual maximums specified may not occur simultaneously. All forces are referenced to the mounting pipe.

VSWR Maximum; is the guaranteed Peak VoltageStandingWaveRatio within the operating band.

Wind Velocity Operational The wind speed where the antenna deflection is equal to or less than 0.1 degrees. In the case of ValuLine antennas, it is defined as a maximum deflection of 0.3 x the 3 dB beam width of the antenna.

Wind Velocity Survival Rating The maximum wind speed the antenna, including mounts and radomes, where applicable, will withstand without permanent deformation. Realignment may be required. This wind speed is applicable to antenna with the specified amount of radial ice.




All specifications subject to change without noticeTelewave, Inc. • San Jose, CA • 1-800-331-3396 ~ 408-929-4400 • www.telewave.comTWDS-7036 Rev. 1/11

445 - 480 MHz

ANT450F6

The Telewave ANT450F6 is an extremely rugged, medium-gain, fiberglass collinear antenna, de signed for op er a tion in all environmental conditions. The antenna is con struct ed with brass and copper el e ments, con nect ed at DC ground potential for lightning impulse pro tec tion.

All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, high-tech radome to ensure survivability in the worst environments. The “Cool Blue” radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives.

The ANT450F6 inc ludes an ANTC482 dual clamp set for mounting to a 1.5” to 3.5” O.D. support pipe, and a 24” removable RG-213 N-Male jumper. Stand-off and top mounts are also available.

90

60

30

0

-30

-60

-90

-60

-30

0

30

60

-3

-10

-20

ANT450F6 - 460 MHzVertical PlaneGain = 6.32 dBd

FIBERGLASS COLLINEAR ANTENNA 6 dBd

SPECIFICATIONSFrequency (continuous) 445-480 MHz Dimensions (L x base diam.) in. 94 x 2.375Gain 6 dBd Tower weight (antenna + clamps) 21 lb.Power rating (typ.) 500 watts Shipping weight 26 lb.Impedance 50 ohms Wind rating / with 0.5” ice 150 / 125 MPHVSWR 1.5:1 or less Maximum exposed area 1.5 ft.²Pattern Omnidirectional Lateral thrust at 100 MPH 60 lb.Vertical beamwidth 18° Bending moment at top clamp 143 ft. lb.Termination Recessed N Female

7-16 DIN-F opt.(100 MPH, 40 PSF flat plate equiv.)

Technical Data Sheet DA6-105BC

TrunkLine Antenna, High Performance, Single Polarized, 6 ft

Allinformationcontainedinthepresentdatasheetissubjecttoconfirm

ationattim

eofordering

RFS The Clear Choice ® DA6-105BC Rev: A / 05. Apr 12 Print Date: 22.09.2014Please visit us on the internet at http://www.rfsworld.com/ Radio Frequency Systems

Product Description(Only available in North America)

RFS TrunkLine Antennas are designed for microwave backbone networks, long distance, high capacitylinksA choice between tested and validated ultra-high (ETSI EN 302 217 Class 3 and FCC Class A) electricalperformance or high (ETSI Class 2 and FCC Class B) performanceSizes ranging from 1.8 m (6 ft) to 4.6 m (15 ft)Single- and dual-polarized models with the ability to upgrade from single to dual polarization and changefrequencies in the field in most cases

Antenna

Features/Benefits• Field-proven reliability and long life• Support for winds up to 200 km/h (125 mph) with high-wind versions that support winds up to 252 km/h(155 mph) and an optional sway bar for added assurance in case mistakes are made during installation• A single-piece configuration and compact packaging to reduce transportation costs• Frequencies ranging from 4 GHz to 15 GHz with support for two wideband frequency ranges (5.725-6.875 and 7.125-8.5 GHz) to reduce antenna requirements and simplify logistics

Technical FeaturesProduct Type Point to point antennas

Frequency, GHz 10.5 - 10.7

Diameter, ft (m) 6 (1.8)

Profile TrunkLine

Reflector 1-part

Swaybar 1: (2.0 m x Ø60 mm)

optional Swaybar 1: SMA-SK-60-2000A (2.0 m x Ø60mm)

Performance High

Polarization Single

Regulatory Compliance ETSI EN 302217 Range 1, class 2 , FCC Category A

3dB beamwidth, (degrees) 1.1

Antenna Input CPR90G

Low Band Gain, dBi 43.5

Mid Band Gain, dBi 43.6

High Band Gain, dBi 43.7

F/B Ratio, dB 68

XPD, dB 30

Max VSWR / R L, dB 1.06 ( 30.7 )

Elevation Adjustment, degrees ± 5

Azimuth Adjustment, degrees ± 5

Polarization Adjustment, degrees ± 5

Radome flexible

Antenna color White RAL 9010

Mounting Pipe Diameter minimum, mm (in) 114 (4.5)

Mounting Pipe Diameter maximum, mm (in) 114 (4.5)

Approximate Weight, kg (lb) 95 (209)

Survival Windspeed, km/h (mph) 200 (125)

Operational Windspeed, km/h (mph) 190 (118)

Further Accessories SMA-WK-6A : Wind Kit< br />SMA-SKO-UNIVERSAL-L : Universal sway bar fixation kit

http://www.rfsworld.com/

Technical Data Sheet DA6-105BC (Cont.)

TrunkLine Antenna, High Performance, Single Polarized, 6 ft

Allinformationcontainedinthepresentdatasheetissubjecttoconfirm

ationattim

eofordering

RFS The Clear Choice ® DA6-105BC Rev: A / 05. Apr 12 Print Date: 22.09.2014Please visit us on the internet at http://www.rfsworld.com/ Radio Frequency Systems

All values @ Survival Wind Speed

FST Side force max, N (lb) 3715 (832)

FAT Fa Axial force max, N (lb) 7500 (1680)

M Torque max., Nm (lb*ft) 2835 (2100)

Dimensions mm (in)

ØA 2000 (79)B 1242 (48.9)C 364 (14.3)D @ Mounting pipe Ø 219 (8.5): not applicableD @ Mounting pipe Ø 114 (4.5): 175 (6.9)D @ Mounting pipe Ø 89 (3.5): not applicableD @ Mounting pipe Ø 48 (1.9): not applicableE 283 (11.1)F 590 (23.2)G not applicableH not applicable

Notesno notes

DocumentationComplete Antenna installation RPE (IQ-Link format)

RPE (Pathloss format)RPE (PDF format)

http://www.rfsworld.com/

http://www.rfsworld.com/WebSearchECat/Datasheets/media/?q=images%2fSMA%2fInstallation%2fNMT628-00.pdf

http://www.rfsworld.com/WebSearchECat/Datasheets/media/?q=images%2fSMA%2fRPE%2fDA6-105B%2c+040225.adf

http://www.rfsworld.com/WebSearchECat/Datasheets/media/?q=images%2fSMA%2fRPE%2fDA6-105B%2c+040225.txt

http://www.rfsworld.com/WebSearchECat/Datasheets/media/?q=images%2fSMA%2fRPE%2fDA6-105B%2c+040225.pdf

Shively Labs®

Document No. ds-6828 (140905)

Model 6828 FM Antenna

A Division of Howell Laboratories, Inc., P. O. Box 389, Bridgton, Maine 04009 USA www.shively.com

(207) 647-3327 1-888-SHIVELY Fax: (207)647-8273 [email protected]

An Employee-Owned Company Certified to ISO-9001

True circular polarization

Handles up to 20 kW per bay 2

Multiplexes over 10 MHz bandwidth

Shively standard features:

• Ring stub design

• Consistently predictable patterns

• -ready

• Pattern studies available

• No factory personnel needed to install

• Radomes and deicers available

• Rugged corrosion-resistant mounts

• Null fill, beam tilt, and special bay spacing avail-able - contact the factory

Performance Specifications:

Polarization: Right circular.

VSWR: < 1.2 : 1 over 10 MHz;

< 1.1 : 1 over 7 MHz.

Azimuth pattern circularity: Horizontal component ± 1.5 dB

on pole.

Input connection: Optional - contact the factory.

Electrical Specifications:

No. of bays

Gain at98.1 MHz

Maximum power rating

Typical power rating, 3-1/8" input 3

Typical power rating, 6-1/8" input 3

Power dB kW kW @ 98 MHz kW @ 98 MHz

1 0.46 -3.40 20 12 —

2 1.01 0.026 40 24 —

3 1.57 1.978 60 36 —

4 2.14 3.318 80 45 —

5 2.71 4.331 100 45 —

6 3.27 5.145 100 45 —

8 4.38 6.416 100 — 90

10 5.49 7.399 100 — 90

12 6.61 8.204 100 — 90

Notes:1. Our gain figures are derived from the computed directivity and include the losses in the antenna feed system. Gain is provided

for one polarization and is equal in circularly polarized antennas for both horizontal and vertical components. Gain will be reduced if null fill, beam tilt is provided. Gain will increase in a directional array by the directivity of the azimuth pattern.

2. With specially-designed rigid feed systems.

3. With high-power flexible feed system and specified input connector size.

Size and weight:

No. of Bays

Vertical Tower Space Weight

Antenna radiation aperture

Physical space used

Total tower space

recommended

Without radomes

With radomes

With radomes & 1/2” (1.2 cm)

radial ice

ft (m) ft (m) ft (m) lb (kg) lb (kg) lb (kg)

1 2.0 (0.7) 7.5 (2.29) 27.5 (8.38) 120 (54.5) 225 (103) 346 (157)

2 9.0 (2.74) 16.5 (5.03) 36.5 (11.03) 240 (109) 450 (205) 692 (315)

3 18.0 (5.48) 25.5 (7.76) 45.5 (13.85) 360 164) 675 (307) 1038 (472)

4 27.0 (8.23) 34.5 (10.52) 54.5 (16.52) 480 (218) 900 (409) 1385 (630)

5 36.0 (10.96) 43.5 (13.24) 63.5 (19.33) 600 (273) 1125 (511) 1731 (787)

6 45.0 (13.72) 52.5 (16.00) 72.5 (22.00) 720 (327) 1350 (614) 2077 944)

8 63.0 (19.20) 70.5 (21.49) 90.5 (27.49) 960 (436) 1800 (818) 2769 (1259)

10 81.0 (24.69) 88.5 (26.97) 108.5 (32.97) 1200 (545) 2250 (1023) 3461 (1573)

12 99.0 (30.17) 106.5 (32.46) 126.5 (38.46) 1440 (655) 2700 (1227) 4154 (1888)

Revision 'G' effective projected area:

No. of Bays

Without radomes

With radomes

With radomes & 1/2” (1.2 cm)

radial ice

With radomes & 1” (2.5 cm)

radial ice

With radomes & 2” (5.1 cm)

radial ice

ft2 ft2 ft2 ft2 ft2

EPAN

EPAT

EPAN

EPAT

EPAN

EPAT

EPAN

EPAT

EPAN

EPAT

1 6.2 5.8 10.9 10.9 13.0 13.0 13.7 13.7 14.9 14.9

2 12.5 11.7 21.7 21.7 26.0 26.0 27.4 27.4 29.9 29.9

3 18.7 17.5 32.6 32.6 34.1 34.1 41.0 41.0 44.8 44.8

4 25.0 23.4 43.4 43.4 52.1 52.1 54.6 54.6 59.7 59.7

5 31.2 29.2 54.3 54.3 65.1 65.1 68.3 68.3 74.7 74.7

6 37.5 35.0 65.1 65.1 78.1 78.1 82.0 82.0 89.6 89.6

8 50.0 46.7 86.8 86.8 104.2 104.2 109.3 109.3 119.5 119.5

10 62.5 58.4 108.5 108.5 130.2 130.2 136.6 136.6 149.4 149.4

12 75.0 70.1 130.2 130.2 156.3 156.3 163.9 163.9 209.9 209.9

Notes:4. The mounting structure must not flex more than ± 1/2 in (± 1.2 cm) in any 10-ft (3-meter) section. 5 feet (1.5 m) of mounting

structure is required above and below the antenna bays for proper pattern formation.

5. Antenna radiation aperture is the distance from the center of the top bay to the center of the bottom bay. Physical space used is from the top of the top bay to the input flange at the bottom of the array, or the bottom of the bottom bay in a center-fed array. Total tower space recommended allows ten feet (3 m) of clear tower space above and below the antenna to protect from pattern interference by other antennas. At frequencies lower than 98 MHz, each of these dimensions will increase by up to 1 ft (0.3 m) per bay.

6. Windload and weight tabulations are estimates. They include the bay and input connection. No values have been included in these tabulations for mounts. Actual values vary with the specific installation. Contact us with details of your installation if more precise values are needed.

7. The effective projected area (EPA) is calculated per TIA standard ANSI/TIA-222-G.EPA

N - Effective projected area associated with the windward face normal to the azimuth of the antenna: EPA

N = Σ(C

aA

c)

N

EPAT - Effective projected area associated with the windward face at the side of the antenna: EPA

T = Σ(C

aA

c)

T

8. Deicers add approximately 1 lb (0.45 kg) per bay in weight and 2 lb (0.9 kg) or 0.05 ft2 per bay in windload.

9. Ask for technical assistance at Shively if you are planning to mount antennas on AM towers or install them at altitudes over 3,000 ft (915 m) above mean sea level.

2

datkins

Highlight

datkins

Highlight

11/13/2014 Hutton Communications: General Dynamics P-9A72GN-S

http://www.hol4g.com/ac/product.aspx?number=TPG-P-9A72GN-S&p=257533&sc=0 1/1

CUSTOMER LOGIN

United States: 877-648-8866 Canada East: 800-265-8685 Canada West: 800-463-4793

Home | Products | Market Segments | Overview | Resource Library | Customer Service | Contact Us | Site Policy | © 2011-2013 HUTTON

Products

PRODUCT CATEGORIES

Search by Manufacturer

Products Homepage

Hutton Outlet

Welcome to Hutton Communications! Region: CA NA D A (s el ect ed) USA more info

Zoom In

Product Description

P9A72GNS , 6', 940-960 MHZ, 22.1 DBI

GAIN, PARABOLIC GRID, N(F)

NS Non-Cancel Non-Return Item

List Can$ 2,516.48

1

Add to Cart

Part No.: TPG-P-9A72GN-S

Uom: Each

Search

All Products Go

Advanced Search

General Dynamics P-9A72GN-S

Technica l Specif ica tions

Depth 81"

Width 24"

Height 81"

Weight 378 LB

Warranty 1 year

Shipping * Heavy Freight

* A product is usually associated with one of the following:

1) Parcel Freight: Indicates that shipping will typically be completed via UPS, FedEx, USPS or

other carriers that typically transport smaller items.

2) Heavy Freight: Indicates that shipping will typically be completed via Truck.

3) Call For Quote: Indicates a product that requires us to determine the shipping method and

pricing.

Sign In

Secure Sign In

User Name:

Password:

Reset PasswordNew Customer Registration

Antennas

Antenna Accessories

Cables and Connectors

Distributed Antenna Systems

Fiber Optics

Filter Products

In-Vehicle Mounts

IP Network Devices

Power & Related Products

RF Amplifiers

Site Hardware

Test & Measurement Equipment

Tools & Shop Supplies

Towers

Two-Way Radio Accessories

Radios

Home Products Market Segments Overview Resource Library Customer Service

http://www.hol4g.com/mk/

https://www.huttononline.com/ac/s/signin.aspx

http://www.hol4g.com/

http://www.hol4g.com/prod/type.aspx

http://www.hol4g.com/market-segments/enterprise.aspx

http://www.hol4g.com/ho/about/about.aspx

http://www.hol4g.com/rl/tl/tl.aspx

http://www.hol4g.com/cs/cf/cf.aspx

http://www.hol4g.com/ho/contact/contact.aspx

http://www.hol4g.com/cs/cf/TandC.aspx

http://www.hol4g.com/prod/manu.pdf

http://www.hol4g.com/ac/shop.aspx?c=0

http://www.hol4g.com/hse/outletList.aspx

https://www.hol4g.com/ac/doselectregion.aspx?r=2

https://www.hol4g.com/ac/AdvancedSearch.aspx

https://www.hol4g.com/ac/s/ResetPW.aspx

https://www.hol4g.com/ac/s/webregistration.aspx

http://www.hol4g.com/ac/search.aspx?sc=3549
















http://www.hol4g.com/mk/

http://www.hol4g.com/ac/shop.aspx?c=0

http://www.facebook.com/HuttonComm

http://www.twitter.com/HuttonComm

ExtendAir Digital Microwave Radios

Installation & Management Guide

Note: The enclosed manual is for the EX-r Series radios which are very similar to the ExtendAir Series. The manual for the ExtendAir Series is

not yet available.

Contact Exalt Customer Care for any support requirements at 408-871-9890 (7am to 4pm M-F) or email to [email protected]

Models: r5000 / rc5000 / r5000HP r5005 / rc5005 / r5005HP r5010 / rc5010 / r5010HP r5015 / rc5015 / r5015HP

Part Number: 203591-000 Date: 2009-07-30

Exalt Installation and Management Guider-Series Digital Microwave Radios

ii 500000012008-05-09

Legal NoticeThe information contained herein is the property of Exalt Communications, Inc. (“Exalt”) and is supplied without liability for errors or omissions. No part of this document may be reproduced, in any form, except as authorized by contract or other written permission from the owner.

Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders.

The contents of this document are current as of the date of publication. Exalt reserves the right to change the contents without prior notice.

The publication of information in this document does not imply freedom from patent or other rights of Exalt or others.

© 2008 Exalt Communications Inc. All rights reserved.

The Exalt logo is a trademark of Exalt Communications, Inc.

Open-Source License InformationIn addition to proprietary software/firmware, which is the sole intellectual property of Exalt, the r-Series Digital Microwave Radios make use of public (open-source) software/firmware within the terms of use of their respective shared license agreements. Exalt will supply copies of any of this code, within the terms of their individual licensing agreements, upon request.

Open-Source Code License Agreement Website

Linux Operating System GNU GPL Version 2 www.gnu.org

BusyBox CLI GNU GPL Version 2 www.gnu.org

www.busybox.net

GoAhead Web Server Copyright (c) 2003 GoAhead Software, Inc. All Rights Reserved. www.goahead.com

U-boot Boot Code GNU GPL Version 2 www.gnu.orgwww.sourceforge.net

Net-SNMP (see Copyright Notices) www.sourceforge.net

http://www.gnu.org

http://www.gnu.org

http://www.busybox.net

http://www.goahead.com

http://www.gnu.org

http://www.gnu.org

http://www.sourceforge.net


50000001 iii2008-05-09

Table of ContentsLegal Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iiOpen-Source License Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iiList of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiList of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiiAbout this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Related Documentation and Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

The r-Series Digital Microwave Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Basic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Pre-installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Link Engineering and Site Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Familiarization with the r-Series Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Shipping Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Initial Configuration and Back-to-Back Bench Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

RF Output Power Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Time Division Duplex (TDD) Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Link Orientation and Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Radio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Radio Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Synchronization Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Offset Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

When Sync is Lost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Virtual Local Area Network (VLAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Link Symmetry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Simple Network Management Protocol (SNMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

System Installation and Initiation Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Record Keeping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Mechanical Configuration and Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Mounting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Radio Ports and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connector Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Terminating the RF Connectors (EX-4.9r-c, EX-5r-c, EX-5r-c IP) . . . . . . . . . . . . . . 24AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Power Injector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

CAT5 Lightning/Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Reset to Critical Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Antenna/Transmission System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Initial Antenna Mounting (EX-4.9r-c, EX-5r-c, and EX-5r-c IP) . . . . . . . . . . . . . . . 27Transmission Line from Antenna to Radio (EX-4.9r-c, EX-5r-c, and EX-5r-c IP) . . . . 28

Indoor Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29RF Lightning Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29


iv 500000012008-05-09

Antenna Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Configuration and Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Telnet into the Command Line Interface (CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Connect to the Radio in a Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Exalt Graphical User Interface (GUI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Preparing to Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Make Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Log In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Login Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Navigating the GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Summary Status Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Navigation Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Radio Information Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Administration Settings Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Simple Network Management Protocol (SNMP) Configuration . . . . . . . . . . . . . . . . . . . 41

SNMP v1/v2c/v3 Support Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42System Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Ethernet Interface Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48VLAN Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49T1/E1 Configuration Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

T1 Interface Configuration Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51E1 Interface Configuration Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52T1/E1 Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

File Transfer Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54File Activation Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57GPS Information Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Alarms Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Performance Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Event Log Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Diagnostic Charts Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Spectrum Analyzer Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Reboot Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Manual Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Integrated Antenna Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70EX-4.9r-c, EX-5r-c, and EX 5r-c IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Legacy Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

EX-4.9r System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72System Specifications, 5.3GHz Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73System Specifications, 5.4GHz Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74System Specifications, 5.8GHz Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Interface Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77TDM Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77


v 500000012008-05-09

RSL & GPS Sync Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Power/Ethernet Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

General Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Typical Indications of Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Improper RF Cable Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Multipath Propagation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83RF Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Path Obstruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Misaligned Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Faulty Antenna (EX-4.9r-c, EX-5r-c, and EX-5r-c IP) . . . . . . . . . . . . . . . . . . . . . . . . . . 84Improper Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Insufficient Link Margin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Moisture in the Transmission System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Back-to-back Bench Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Basic Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Specification Performance Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

General Compliance and Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Dynamic Frequency Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

4.9GHz Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91United States Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Federal Communications Commission (FCC), United States . . . . . . . . . . . . . . . . . . 91Canada Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Industry Canada (IC), Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Antennas Supported in Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Europe and ITU Country Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Regulatory Domain Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96EIRP Limits for the United States and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

EX-4.9r EIRP for the USA and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97EX-5r Series EIRP for the US and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

5250–5350 MHz Band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 5470–5725 MHz Band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 5725–5850 MHz Band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

EIRP Limits for Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99EX-5r Series EIRP for Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

5470–5725 MHz Band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 5725–5850 MHz Band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

EIRP Limits for the European Union and ITU Countries . . . . . . . . . . . . . . . . . . . . . . . . . . 100EX-5r Series EIRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

5250–5350 MHz band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 5470–5725 MHz band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 5725–5850 MHz band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Declaration of Conformity to the R&TTE Directive


vi 500000012008-05-09

1999/5/EC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103EU WEEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103EU RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Exalt Limited Hardware Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105Exclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105RMA Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Copyright Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112


vii 500000012008-05-09

List of FiguresFigure 1 Exalt EX-5r (integrated antenna model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Figure 2 Mounting and cabling—integrated antenna model . . . . . . . . . . . . . . . . . . . . . . . . . 4Figure 3 Cabling and mounting—external antenna model. . . . . . . . . . . . . . . . . . . . . . . . . . . 5Figure 4 Synchronized GPS sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Figure 5 Radio installation tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Figure 6 Pole-mount example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Figure 7 r-Series pole and wall mount (with azimuth and elevation adjustment) . . . . . . . . 20Figure 8 EX-4.9r-c, EX-5r-c, and EX-5r-c IP pole/wall mount . . . . . . . . . . . . . . . . . . . . . . 20Figure 9 r-Series connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Figure 10 Power injector connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Figure 11 CLI main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Figure 12 Initiating the browser connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Figure 13 Browser Login screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Figure 14 Radio Information page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Figure 15 Exalt GUI window description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Figure 16 Summary status information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Figure 17 Radio Information page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Figure 18 Administration Settings page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Figure 19 SNMP Configuration page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Figure 20 System Configuration page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Figure 21 Ethernet Interface Configuration page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Figure 22 VLAN Configuration page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Figure 23 T1 Interface Configuration page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Figure 24 External (remote) loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Figure 25 External (local) loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Figure 26 Internal loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Figure 27 File Transfer page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Figure 28 File Transfer page—download file link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Figure 29 File Activation page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Figure 30 GPS Information page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Figure 31 Alarms page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Figure 32 Performance page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Figure 33 Event Log page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Figure 34 Diagnostic Charts page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Figure 35 Spectrum Analyzer page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Figure 36 Spectrum analyzer graph example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Figure 37 Reboot page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Figure 38 Manual page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Figure 39 r-Series connector orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Figure 40 TDM connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Figure 41 RSL & GPS connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Figure 42 Power/Ethernet connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Figure 43 Basic back-to-back bench test configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85


viii 500000012008-05-09

List of TablesTable 1 Factory default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Table 2 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Table 3 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Table 4 Recommended transmission line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Table 5 Default login information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Table 6 Alarm status indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Table 7 Supported antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Table 8 Product Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Table 9 Regulatory Domain Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Table 10 EU and ITU Country Specific EIRP Levels for EX-5r Series . . . . . . . . . . . . . . . 101


50000001 12008-05-09

About this DocumentThis manual provides a complete description of the r-Series Digital Microwave Radios and related software. This manual provides planners, engineers, installers, system administrators, and technicians general and specific information related to the planning, installation, operation, management, and maintenance of these devices.

Revision History

IconsThe following icons denote specific types of information:

Date Products and Release code

2006-09-19 EX-5r & EX-5r-c v1.0.0

2007-02-19 EX-4.9r v1.0

2007-02-23 EX-5r and EX5r-c v2.0.0 (GPS, Sync, SNMP feature release)

2007-04-20 EX-4.9r v1.1 (AES feature release)

2007-07-27 EX-5r IP and EX5r-c IP v 2.1.0

EX-5r and EX-5r-c v2.1.0 (Regulatory Domain Key, Base License Key, and Dynamic Frequency Selection feature releases)

2007-10-26 EX-5r, EX-5r-c, EX-5r IP and EX-5r-c IP v3.0 (Spectrum Analyzer, VLAN, Asymmetry, Legacy SNMP and Enhanced Event Log feature releases)

2008-03-08 New chassis release.

2008-05-09 Updated contact information.

Note: This symbol means take note. Notes contain helpful suggestions or references to materials not contained in the manual.

Warning! This warning symbol means there is a risk of electric shock. This situation that could cause bodily injury. Before working on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.

Caution! This symbol means be careful. There is a risk of doing something that might result in equipment damage or loss of data. This is a general warning, caution, or risk of danger.


2 500000012008-05-09

IntroductionExalt Communications, Inc. thanks you for your purchase. Our goal is to build the highest quality, highest reliability digital microwave radio products. This commitment to quality and reliability extends to our employees and partners alike. We appreciate any comments on how we can improve our products, as well as your sales and Customer Care experience.

Related Documentation and SoftwareThis manual makes reference to other documentation and software files that may be necessary. To access all documents and software mentioned in this manual visit:

http://login.exaltcom.com/

You must have a user account to view all downloads. Follow the online instructions to create a user account and request access.

The r-Series Digital Microwave RadiosThe r-Series Exalt Digital Microwave Radios are the most advanced carrier-class point-to-point terrestrial radio communications devices operating in the 4940 to 4990MHz and 5250 to 5850MHz frequency bands. The r-Series radios are available in the following configurations:

• EX-4.9r, EX-5r, and EX-5r IP have integrated software selectable polarization antenna

• EX-4.9r-c, EX-5r-c, and EX-5r-c IP have external antenna connectors, which allows connection of either one single- or dual-polarized antenna (with software selectable polarization)

Exalt Communications supports two physical forms of the r-Series radios:

• Legacy model, which has custom weatherproof connectors; the r-c models have the RF connectors on the front

• Updated model, which has weatherproof connectors that accept standard RJ-45; the r-c models have the RF connectors on the rear

In this guide, the term Legacy is used where necessary to differentiate the two forms.

The r-Series radios connect voice and/or digital data from one location to another, obviating the need for copper or fiber connectivity, or enhancing existing connectivity by providing a redundancy solution, a primary solution, and/or additional capacity. Figure 1shows the Exalt EX-5r digital microwave radio.

Customer Care Hotline (USA): (408) 871-9890

Toll-Free Customer Care Hotline (USA): (877) EXALT-01 (392-5801)

Direct-Dial Telephone (USA): (408) 871-1804

Website: www.exaltcom.com

Sales e-mail: [email protected]

Customer Care e-mail: [email protected]

Mailing Address: Exalt Communications, Inc.

580 Division St.

Campbell, CA 95008

USA

http://login.exaltcom.com/


50000001 32008-05-09

Figure 1 Exalt EX-5r (integrated antenna model)

The r-Series radios require a clear line-of-sight and proper path clearance to achieve a high-performance, reliable connection. Perform professional path engineering and site planning before installing this equipment.

The primary focus of this document is the installation and maintenance of the digital microwave radio, and assumes that path engineering and site planning has already been performed. Please refer to the Exalt document, Guidance for Engineering and Site Planning of Terrestrial Wireless Links, for detailed information on these activities.

The EX-4.9r and EX-4.9r-c radios utilize radio frequencies in the 4940 to 4990MHz range, which is typically a licensed band range reserved for use by Public Safety agencies and applications. This band is not generally available outside North America.

The EX-5r, EX-5r IP, EX-5r-c, and EX-5r-c IP radios utilize radio frequencies in the 5250 to 5850 MHz range. In most countries these frequency bands are considered as ‘license-exempt’ or ‘unlicensed.’ This means that virtually any user may use these frequencies freely, without paying for access, or any type of pre-notification, post-notification or registration. As a result of this designation, users may also move or change these systems at any time, with significant flexibility to the location, orientation and configuration of the system. However, due also to this designation, there may be uncontrolled interference from other similar devices that occupy this spectrum. In these cases, it is up to engineering and maintenance personnel to design the system with existing and future interference sources in mind, recognizing that there is a chance that the interference conditions could be very dynamic, and outages may occur on the system as a result, and that, in some very rare cases, the system may cause interference into another system and may be required to be disengaged or modified/re-oriented to eliminate the interference.

If the spectrum in your country is designated as ‘license-exempt’ or similar, this does not infer that the installer may configure the system in any manner at any location. In most cases, there are regulations, or device-based conditions that limit the use of the device, such as maximum gain antenna, antenna types and maximum output power, as well as, in some cases, application limits, limited geography of use, and other unique regulations. The link design engineer and/or professional installer must determine these limitations and engineer/install the system within the confines of all local regulations. Also, it is required to examine any regulations that may apply to peripheral equipment, installation and cabling of the system that may be regulated for human safety, electrical code, air-traffic control, and other safety-related categories.


4 500000012008-05-09

In certain countries, the spectrum for this product is NOT considered to be license-exempt. In these cases, there may be additional regulatory requirements concerning the location, frequency, power, orientation, configuration, and other aspects of the system, including, in some cases, a need for link registration, coordination, and fees that may apply to the system usage. Please consult your local regulatory organization(s) to determine usage requirements.

In almost all cases, either for license-exempt or other designation, the product itself must be authorized for use in your country. Either Exalt or Exalt’s agent must have applied for certification or authorization to allow the sale and deployment of the system within the country. It is also possible that only certain versions or configurations of the device are allowed within a particular country. Please contact Exalt or your authorized Exalt representative for information pertaining to your country.

Basic FeaturesThe r-Series Digital Microwave Radios are intended for all-outdoor mounting and come with an indoor-mounted power injector. In some cases, the radio can be mounted indoors or in an enclosure. Depending on the configuration purchased, the associated antenna is either integrated as part of the unit or connected separately.

For the integrated antenna model, the entire unit is typically mounted on a tower or rooftop mast structure, with Ethernet/Power and other optional interface cables running from the unit location, through a structure penetration, and to the power injector and connected communications equipment.

For the external antenna model, the unit is typically mounted very close to the external antenna to minimize RF cabling and associated losses. Alternatively, the unit can be mounted at an easily accessible location with longer RF cabling to the antenna. Proper lightning or surge suppression devices and associated grounding are required for all connections.

Figure 2 Mounting and cabling—integrated antenna model

Note: It is the (professional) installer’s responsibility to ensure that the radio system is implemented in a legal fashion. Exalt is not liable for any unsafe or illegal installations.


50000001 52008-05-09

Figure 3 Cabling and mounting—external antenna model

For highest performance and reliability, it is advised to minimize the length of RF cable and associated transmission system losses between the antenna and the radio’s antenna port.

The r-Series radios provide connections for a combination of the following data communication interfaces:

• 10/100BaseT Ethernet

• 4xT1/E1 interfaces for synchronous voice traffic (except EX-5r IP and EX-5r-c IP)

The r-Series radios are powered by a combined Power/Ethernet cable, and associated power injector. The power injector provides 48VDC to the unit.

The r-Series radios provide the following primary features and benefits:

• Low-latency optimization and control for voice and data connections

• Very high throughput and flexible interface configurations with voice+data combinations

• Encryption for extreme wireless security

• Easy-to-use management and configuration

• Flexible utilized channel bandwidth

selection for interference avoidance and frequency coordination

• Flexible center frequency tuning

for interference avoidance and frequency coordination

• Flexible capacity to meet current connection requirements and future growth needs

• Carrier-class reliability and performance

• Connector covers (for covering and securing unused connectors) — Legacy models include a safety ring

• (Legacy models only) Safety ring and 3'/1m PoE cable


6 500000012008-05-09

Pre-installation TasksThis section describes the steps necessary to prepare a site for the installation of the Exalt Digital Microwave Radio.

Link Engineering and Site PlanningDesign all terrestrial wireless links prior to purchase and installation. Generally, professional wireless engineering personnel are engaged to determine the viability and requirements for a well-engineered link to meet the users’ needs for performance and reliability.

The reader is referred to the Exalt document, Guidance for Engineering and Site Planning of Terrestrial Wireless Links and the ExaltCalc path calculator. This document and calculator aid in the pre-planning and engineering required to determine following attributes:

• Antenna type gain at each end of the link

• Antenna mounting height/location for proper path clearance

• Antenna polarization orientation

• RF cabling type, length, connectors, route, and mounting

• Antenna system grounding

• Lightning arrestor type(s), location(s), and grounding

• Radio mounting location and mechanisms

• Radio grounding

• Radio transmitter output power setting

• Anticipated received signal level (RSL) at each end

• Anticipated fade margin and availability performance at each end

• Radio settings for TDD frame length and occupied bandwidth

• Anticipated throughput performance (TDM circuit support and Ethernet)

• Anticipated system latency

With respect to radio path and site planning, these radios are generally identical to other microwave terrestrial wireless systems. Engineering of these systems requires specific knowledge about the radios, including:

• RF specifications (transmitter output power, receiver threshold, occupied channel bandwidth, and carrier-to-interference to erance)

• Regulatory limitations on transmitter output power setting and antenna type/gain

• Noise/interference profile for the intended location

Familiarization with the r-Series RadiosThe r-Series radios utilize time division duplex (TDD) radio transmission. This means that the transmitted signal in both directions uses the same center frequency and transmits in one direction for a period of time, and then in the opposite direction for another period of time. This total period of time is referred to as the frame length or TDD frame length, and is further discussed in Time Division Duplex (TDD) Factors.


50000001 72008-05-09

The two radio terminals are identical hardware, except for the TDD setting in software. When the radios are in their default state, both radios are configured as Radio B. One end of the link must be configured as Radio A before the two ends of the radio system can communicate. It can be considered that Radio A is the primary radio in the link. Radio A provides the master clock and control to Radio B. For most applications, it is not important how the radio link is oriented, only that one end is configured for Radio A and the other for Radio B. For some applications (such as, multi-radio hub sites or repeaters), the orientation of the radio systems may be more critical. See Link Orientation and Synchronization for details.

There are two ways to configure the radios for Radio A/B determination:

• Use the Exalt browser-based graphical user interface (GUI) – preferred.

• Connect to the radio using Telnet.

Exalt recommends using the Exalt GUI for radio configuration. This interface requires a computer with an Ethernet port and web browser software, such as Microsoft Internet Explorer 5.0 or above. See Configuration and Management for details on how to connect to and use the browser-based GUI interface.

Shipping Box ContentsUnless purchased as a spare terminal, the radios are shipped as a complete hop (that is, a radio link pair consisting of two terminals). An outer box has labeling that indicates the contents of the box, with the part number and serial number details for both radio terminals.

Inside the outer box are two identical boxes, each of these boxes is also marked with the part number and serial number of the individual terminal contained inside the box. The terminal box contains the following items:

• Radio terminal (configured as Radio B)

• AC adapter

• Power injector

• Mounting kit (for pole or wall mounting)

• Accessory kit

– Grounding screw/washers

– Connector covers with safety ring (for covering and securing unused connectors)

– Weather-sealing tape (required for RF connectors on the EX-4.9r-c, EX-5r-c, or EX-5r-c IP)

– RF connector cover (for the EX-4.9r-c, EX-5r-c, or EX-5r-c IP covering the unused RF connector, where applicable)

– RSL adapter cable

• Registration card

• Quick-start guide

• 3'/1m PoE cable (with safety ring)

Inspect the outer packaging and the contents of the boxes upon receipt. If you suspect any shipping damage or issues with the contents, contact Exalt Customer Care.


8 500000012008-05-09

The radio terminal boxes contain a single pre-terminated PoE cable intended for bench testing and to make the short connection between the radio and the PoE lightning arrestor near the radio. If running a longer cable from the radio to the PoE lightning protector (such as at the egress point), use pre-terminated cables (sold separately). Pre-terminated cables are available in different lengths to meet a variety of applicationss, and can also be used for the T1/E1 connections (where applicable).

Initial Configuration and Back-to-Back Bench Test Every Exalt digital microwave radio goes through extensive quality testing and performance evaluation over the full operating temperature range prior to shipment. However, before installation, it is strongly advised to perform several tests and tasks that are much more difficult to perform once the radio link endpoints are distant from one another. A back-to-back bench test and pre-configuration will provide confidence that the radio link is operational and properly configured prior to installation, so that if troubleshooting is necessary, the radio hardware and configuration settings are eliminated from the troubleshooting process. Verify the following in the back-to-back testing:

• Confirm that the radio system is generally operational

– Radios power-up with planned power and wiring solutions

– Regulatory Domain Key (RDK) entry successful

– RF link connects in both directions

– Traffic passes across the link

– Configure connected equipment and cabling

– Test Ethernet (CAT5) cabling, and/or T1/E1 cabling, any auxiliary connector cabling and configure all interfaces

– Configure IP settings for configuration and management

– Configure passwords and security modes

– Become familiar with the configuration and management interfaces through the Exalt GUI interface

– Configure radio parameters

– Set transmitter output power to engineered or allowed level (see RF Output Power Setting)

Note: Register your system as soon as possible. A 2-year Warranty period applies to products registered within 90 days of purchase. The Warranty period is reduced to 1-year for unregistered products and products registered after the first 90 days.

Note: Exalt radios with the RDK function are DISABLED when initially shipped. To ENABLE the radio, a valid RDK must be entered on the Administration Settings Page page of the Exalt GUI. The RDK references the unit's serial number and is provided based on the country and/or region where the radio system will be deployed. The RDK is obtained through your Exalt Authorized distributor or reseller.

Note: Some countries require Dynamic Frequency Selection (DFS) , which delays the transmitter turn-on time during the initial Channel Availability Check period of 1 minute. In accordance with these regulations, the radios boot up, and then wait for 1 minute before linking.


50000001 92008-05-09

– Set operating center frequency

– Set link distance, occupied channel bandwidth, and frame length

• Make detailed radio performance measurements

– Measure transmitter output power

– Measure receiver threshold performance

– Confirm unfaded error-free performance

Some of these tasks may not be possible or practical within a bench test environment due to the nature of the remote connectivity of peripheral equipment. However, it is good practice to perform as much as possible in this environment to minimize field/installation time and troubleshooting efforts.

Detailed performance measurements are usually not required for pre-installation, but can be easily performed at this stage and may be helpful for later troubleshooting efforts or for internal records. During troubleshooting, there may often be a point at which a back-to-back bench test should be performed to verify many or all of the above items, and in the case of a suspected faulty device, to help confirm the fault and determine which end of the system is at fault and in need of repair or replacement.

RF Output Power Setting

The maximum RF output power is bounded by one of the following criteria:

• Maximum RF output power setting capability of the radio device

• Maximum RF output power allowed/authorized by the local government regulations and for this specific device

• Maximum effective isotropic radiated power (EIRP) of the transmission system allowed/authorized by the local government regulations and for this specific device

• Desired RSL to not exceed the maximum RSL allowed by the device

• Desired RSL to minimize/eliminate interference into neighboring systems

Time Division Duplex (TDD) FactorsThe r-Series radios are very dynamic, allowing the installer to optimize and control the performance of the radio system for the intended application. The following parameters must be carefully determined during the link engineering phase:

• Link distance

• Bandwidth

• TDD frame size

• Mode (modulation)

Note: See Back-to-back Bench Testing for detailed instructions.

Note: In many cases the radio must be pre-configured for legal maximum output power before connecting to the antenna and transmission system. Instructions for adjusting the output power can also be found at the rear of this guide in the EIRP section for your region.


10 500000012008-05-09

• The setting of the above parameters determines the following performance factors:

• Number of supported T1/E1 channels (on applicable models)

• Ethernet throughput

• System latency (delay)

Use the ExaltCalc calculator to determine optimum settings for the above parameters to meet the needs of your application.

The following generalizations can be made with regards to these factors:

• The shorter the TDD frame size, the lower the latency

• The shorter the link distance, the lower the latency, the higher the throughput

• The longer the TDD frame size, the higher the throughput

• The higher the bandwidth, the higher the capacity

• The higher the mode, the higher the capacity

Link Orientation and SynchronizationLink orientation refers to the Radio A and Radio B placement in your network. Link synchronization refers to using external or internal timing to coordinate multiple links.

For every link, one end of the radio link must be configured as Radio A, while the other end is configured as Radio B. In single-link systems, it does not matter which end of the system is mounted at which end of the link, and there is typically no requirement for any link synchronization.

Link orientation and synchronization are more important for networks with site(s) where there is more than one link of the same type or for sites using the same type of radio that are very close to each another at one or both ends.

Configure collocated radio terminals for the same link orientation. That is, configure all radios at the same location as Radio A or Radio B.

It can be advantageous to utilize link synchronization for collocated links. The radios allow the use of an optional GPS synchronization kit. This synchronization controls the transmitter and receiver frame timing so that collocated radios are transmitting at the same time and receiving at the same time. This can substantially reduce the opportunity for self-interference. Without synchronization, collocated radios may be transmitting and receiving at the same time, incurring near-end interference.

Note: Disable all T1/E1 ports if there are no T1/E1 interfaces connected. This shifts all available throughput to the Ethernet interface.

Note: If a selected combination of the Link Distance, Frame Size, Bandwidth, and Mode parameters cannot support all the desired T1 or E1 ports, the ports that cannot be supported are automatically disabled. Priority is placed on the T1/E1 port number. That is, the first port to be disabled, if necessary, is the highest port number, such as Port 4. See T1/E1 Configuration Pages for more information.


50000001 112008-05-09

Radio A/B Configuration

Use the Exalt GUI to configure the radio terminals for Radio A and Radio B orientation. Since many other parameters also need to be set, and the Exalt GUI is needed for these configurations, this is the best way to completely configure the radio terminals.

Radios arrive from manufacture in default configuration, orientated as Radio B and configured as shown in Table 1.

Note: It is not always necessary to synchronize collocated radios. If antennas are substantially separated or blocked from one another and/or frequency separation tuning is used, the opportunity for near-end interference can be eliminated.

Note: When synchronization is required or desired, one GPS kit is required for each r-Series radio link in the connected or collocated network.

Table 1 Factory default settings

Parameter EX-5r, EX-5r IP, EX-5r-c, and EX-5r-c IP Settings EX-4.9r and EX-4.9r-c Settings

Frequency 5788 MHz (5600 or 5785 MHz if the regulatory domain does not allow 5788 MHz)

4965 MHz

Transmit Power +4dBm +4dBm

Link Distance <10 miles <10 miles

Bandwidth 8 MHz (10 MHz for some regulatory domains) 10 MHz

Mode Mode 1 Mode 1

TDD Frame Size 2ms 2ms

Link Security Key 000000000000 000000000000

Administration Password password password

User Password password password

IP Address 10.0.0.1 10.0.0.1

IP Mask 255.0.0.0 255.0.0.0

IP Gateway 0.0.0.0 0.0.0.0

Ethernet Interface Alarm Enabled, 100/Full Alarm Enabled, 100/Full

T1/E1 Enabling All Disabled All Disabled


12 500000012008-05-09

Radio ResetUse the reset function if the IP address and/or passwords are lost. Use the following steps to perform a critical parameter reset:

1 Remove power from the radio by disconnecting the AC adapter from the power injector.

2 Hold down RESET button on the power injector while applying power.

Hold the RESET button down through the entire power cycle and monitor the DATA+POWER left LED on the power injector. Release the RESET button only after the LED is in the steady state (45 to 60 seconds).

3 Release the RESET button.

The following configurations are reset on the radio:

• IP address = 10.0.0.1

• IP mask = 255.0.0.0

• IP gateway = 0.0.0.0

• Administration password = password

• User password = password

Radio SynchronizationThe radio synchronization feature improves the performance of Exalt radios operating in the same frequency band and that are collocated (such as in repeater and hub configurations). Radio synchronization ties radio systems together to operate off of a common clock system, ensuring that all radios simultaneously transmit and receive, and thus eliminating near-field interference issues and related radio system coupling.

Synchronization ModesSynchronization can be accomplished using a GPS source. A Global Positioning System (GPS) kit from Exalt is required to implement external source synchronization. GPS synchronization is not available on all radio models. Contact your Exalt representative for details.

Synchronization implementation requires one synchronization source for each link.

Virtually any combination of hubs and repeater sites, star configurations, and/or backbones can be implemented with synchronization. It is typically necessary or ideal in each configuration to match the following parameters on every radio in the network:

• Link Distance – Match to the longest distance link in the network.

Note: In many cases, the system design will not be identical to the factory default configuration, and in some cases, these differences prohibit the installation of the radio. If at all possible, obtain a computer and configure the radio terminals using the browser-based GUI. See Exalt Graphical User Interface (GUI) for details.

Note: The synchronization function is not currently available on all Exalt radio models. A firmware upgrade may be required for models without sync if sync is desired. Contact your Exalt representative for details.


50000001 132008-05-09

• Frame Length – Match to the lowest frame length to optimize total system latency (for example, for TDM networks) or match to a highest frame length to optimize user throughput. Choose an intermediate value to compromise between latency and throughput.

• Mode – It is desirable, but not always necessary, to match the mode for all collocated links.

• Bandwidth – It is desirable, but not always necessary, to match the bandwidth for all collocated links.

For complex networks, an Exalt engineer should review multi-link networks before deployment as several factors can optimize the network for desired performance.

Figure 4illustrates two separate radios benefiting from synchronized GPS sources.

Figure 4 Synchronized GPS sources

Offset TimingManual control of offset timing is also allowed. This provides a means to delay the synchronization signal using a user-defined offset. This is helpful when Exalt radios are near other devices operating in the same frequency band that also use a timing source, such as GPS. The timing source to the Exalt radios can be adjusted to match the other radio system timing source mechanism.

Offset timing can also optimize timing intervals for repeaters and backbones. As the distance of each link results in a unique factor for speed-of-light transmission of the radio signal, a subsequent radio can be delayed in timing so that the overall synchronization of radios is precisely maintained.

Offset timing can be adjusted in 1-ms intervals, from zero to the radio’s frame length setting. For example, if using a 2-ms frame length, the offset timing can be set from zero up to 1999 ms.

Note: When GPS Sync is enabled, link initiation typically takes 1 to 3 minutes to allow for the radio to properly synchronize to the available GPS satellites.


14 500000012008-05-09

When Sync is LostIf the primary sync source (for example, the GPS source) signal is lost due to equipment failure, a disconnected sync cable, loss of satellite link, or other condition, the radio is said to be flywheeling. When flywheeling, the radio’s clock is free-running off internal clocking and is no longer synchronized to any source. If the original sync source is restored to the flywheeling radio’s configuration, it attempts to synchronize to this signal without causing transmission interruption.

When the flywheeling radio runs independently for long periods of time, the synchronization signal may be too far outside the capture range of the synchronization loop, and portions of transmission frames can be lost during this re-synchronization process. This condition is temporary and all interconnected radios will re-synchronize to the sync source, as necessary.

If the flywheeling period is exceeded, the radio will stop transmitting. There is a setting for infinite flywheeling; however, long periods of flywheeling can cause interference with collocated radios.

Virtual Local Area Network (VLAN)VLAN segments information in a single connection and creates multiple separate connections to secure information of one type or for one set of users from other information types or for other sets of users. Exalt’s VLAN communications implementation adheres to the IEEE standard 802.1q.

In most cases, an Exalt radio acting as a Layer 2 bridge between two locations is only required to pass traffic with VLAN tagging. Without additional configuration, all Exalt radios support frame sizes in excess of 1900 bytes, which currently supports all defined VLAN packet sizes.

Some situations require Exalt radios to act upon VLAN traffic and perform any or all of the following functions:

• Connect specific traffic, using VLAN tagging, to different purposes, such as management traffic to the radio’s NMS system.

• Allow only traffic with specifically assigned VLANs to pass across the link, blocking all other VLANs or any non-VLAN traffic.

• Allow management access only through a VLAN connection, leaving the main traffic transparent.

• Allow management access without a VLAN connection, but flowing only specific VLAN traffic across the link.

Link SymmetryThe default configuration of r-Series radios provides 50/50 symmetrical throughput. The Tx/Rx Throughput Ratio setting enables programming different symmetry for applications where significantly higher throughput in one direction is anticipated such as for video broadcast, video aggregation, or remote server/storage WANs.

Note: Offset timing is not currently supported in all models. Consult your Exalt representative for details.

Note: If an application only requires the transparent passing of VLAN traffic, disable the VLAN function.

Note: Currently, not all Exalt radio models include VLAN configuration. For models with VLAN configuration support, use the VLAN Configuration Page in the Exalt GUI.


50000001 152008-05-09

Exalt does not recommend placing two links with asymmetry back-to-back in a serial configuration due to the TDD cycle of the radios. This configuration requires that one radio transmits in an overlapping time period while another radio is receiving. Physical antenna isolation and/or frequency channel spacing may accommodate this configuration. Asymmetry is, however, ideal for single-hop, multi-link hub/spoke architectures, or simply single independent links.

TDD frame sizes of 2ms and 5ms are supported. The 5ms configuration maximizes the aggregate throughput of the radio for every situation. The 2ms configuration reduces latency to meet latency-critical applications, especially for multi-link and TDM circuit support. The following RF BW/mode combinations are supported for these two configurations:

• 16MHz/Mode1

• 16MHz/Mode2

• 32MHz/Mode1

• 32MHz/Mode2

• 64MHz/Mode1 (64MHz requires a license key)

The following Tx/Rx ratios are supported for these two configurations:

• 65/35 and 35/65

• 80/20 and 20/80

For example, a radio configuration of 32MHz/Mode2 with a 5ms TDD frame size supports up to 110Mbps user capacity or 55Mbps full-duplex. By selecting 80/20 on one side of the link and 20/80 on the other side, the radio allows up to 88Mbps in one direction, and 22Mbps in the opposite direction.

T1/E1 is supported with asymmetric settings. However, based on the BW/mode setting (and in some cases, TDD frame size and distance), the direction with the limited throughput limits the number of T1 or E1 connections obtained. For example, the 16MHz/Mode1 setting typically supports up to 27Mbps aggregate throughput. In the 80/20 ratio configuration, one direction is limited to 5.4Mbps, which is less than 3xE1 and less than 4xT1. Since TDM connections must be symmetrical, this setting therefore limits throughput to no more than 2xE1 or 3xT1.

Simple Network Management Protocol (SNMP)The Exalt radios primarily use a browser-based graphical user interface (GUI) for radio configuration and management, as described in Exalt Graphical User Interface (GUI). In addition, a command line interface (CLI) is provided for serial and/or Telnet access, as described in Configuration and Management. SNMP is often used for management of larger networks as described here. Use SNMP to manage networked devices and execute the following functions:

• GET: Obtain information from the device, such as a configuration setting or parameter.

• SET: Change a configuration setting on the device.

Note: Asymmetry is only supported for a specific subset of system configurations that are optimized for typical asymmetric applications.

Asymmetry is not currently supported in all r-Series radio models. Consult your Exalt representative for details.

Note: GPS sync is supported with asymmetric settings, but in addition to the other requirements for sync, all radios tied to sync must be set with matching ratios.


16 500000012008-05-09

• TRAP: The device proactively informs the management station of a change of state, usually used for critical alarms or warnings.

One feature of the SNMP implementation is that system configuration changes do not take effect using the SET command. Instead, groups of configuration settings can be preconfigured for global change, and a single ‘Save’ (Commit) command implements all changes.

When some parameters are changed, a link may drop and/or management control lost. MIB files allow many parameters to be set at once, allowing only a temporarily dropped link or management control issue. The opposite end radio can be quickly reconfigured, with little downtime for the link and management control. The save (Commit) command is similar to the Update button.

Dropped links or management control issues do not occur with every parameter change. Many configuration changes do not impact traffic or management access.

Exalt radios utilize SNMPv3, a high security version of SNMP, to ensure secure access to and storing of management data. The SNMPv3 security string matches the admin and user passwords. Passwords must be eight characters or longer. Some models also have legacy SNMP support for customers requiring SNMPv1 and/or SNMPv2.

Note: Currently the SNMP implementation does not support TRAP functions. For critical alarms, use the GET command for specific alarm conditions.

Note: Currently not all Exalt radios implement SNMP. Check the software release notes to verify that the function is available. Generally, the radio supports SNMP when MIB files are listed on the File Activation Page.


50000001 172008-05-09

System Installation and Initiation ProcessThe tasks required for radio installation and initiation are outlined in the following figure.

Figure 5 Radio installation tasks

Path & Site Analysis

Link Design

Build Antenna Structures &

Egress

Mount Antennas &

Transmission Line

Install & Test Network &

Power Wiring

Read This Manual

Completely

Pre-configure Radios

Perform Back-to-Back

Test

Mount Radios

Connect Transmission

Line

Connect Power

Align Antennas to Planned RSL

Verify LEDs for Good Link

Test Network Connectivity

Connect & Test Primary

Services

Test Network Management

System

Both Transmission System & Radio

Preparation Tasks Must Be Complete

Transmission System Tasks Radio Preparation Tasks


18 500000012008-05-09

Record KeepingAfter installation, record the following items for ongoing maintenance and future troubleshooting. Keep a record for each end of the radio link and store a copy of these records at the radio location, at the opposite end radio location, and a central record storage location.

• GPS coordinates for antenna locations at each site

• Antenna heights above ground level (AGL), as mounted

• Antenna model numbers, serial numbers, and specifications

• Antenna polarization as mounted

• Length/type of primary transmission lines at each site

• Model number and serial number of RF lightning arrestors

• Length/type of secondary transmission line(s)

• Transmitter output power setting as installed at each site

• RSL as measured after antenna alignment at each site

• Designed RSL per original design at each site

• RSL reading with far-end power off (from each end)

• Spectrum analyzer plot with far end off at each site

• Voltage standing wave ratio (VSWR)/return loss at radio’s antenna connector at each site

• Radio’s network management IP address at each site

• Radio’s network management gateway address at each site

• Radio’s operating frequency, bandwidth setting, and mode of operation

• Optionally purchased extended warranty and/or emergency service contract details

In addition, certain information may be desired for central record-keeping only:

• Link security codes and log in passwords (stored in a secure place)

• Photographs of complete installation

• End-user sign-off/acceptance documentation (if any)

• Photo of product identification label (part number, serial number, MAC address information)

• Electronic copy of radio’s configuration file

• Electronic copy of radio’s installed software


50000001 192008-05-09

InstallationThis section presents all tasks required to install the Exalt Digital Microwave Radio.

Mechanical Configuration and MountingThe r-Series radios are environmentally sealed units intended for deployment outdoors. The device must be deployed within an ambient temperature range as specified, and with non-restrictive airflow around the chassis. The EX-4.9r-c, EX-5r-c, and EX-5r-c IP can also be mounted in an enclosure or indoors. The same airflow and temperature conditions apply. All r-Series models can be mounted behind a window if window losses are considered in the link budget calculation.

Provide proper clearance for all cables and connectors attached to the device.

Note that for the EX-4.9r-c, EX-5r-c, and EX-5r-c IP the RF cable connector may require significant clearance for the bend radius of the coaxial cable assembly. All RF connectors, cables, and adapters must be rated for operation within the radio’s frequency range. RF connector losses must be accounted for within the link engineering design and output power settings.

Mounting the SystemUse the mounting system supplied with each terminal for wall or pole mounting (Figure 6). The pole mounting kit can accommodate a pole 2–5"/5–13cm in diameter. Install the mounting system first, and then affix the radio to the mount. The radio can also be affixed to the mount, and the entire assembly (including radio) mounted.

Figure 6 Pole-mount example

Figure 7 illustrates the pole/wall mount assembly, showing the azimuth and elevation adjustment points.

Note: The power injector and power supply must be placed indoors or in an enclosure.

Note: There are two RF connectors on the EX-4.9r-c, EX-5r-c, and EX-5r-c IP which facilitate connection to a cross-polarized antenna for polarization diversity. Seal the secondary connector when using a single-polarized antenna. Use the N-type cover cap and weather-seal tape included in the accessory kit to weatherproof this connector.


20 500000012008-05-09

Figure 7 r-Series pole and wall mount (with azimuth and elevation adjustment)

Figure 8 illustrates the EX-4.9r-c, EX-5r-c, and EX-5r-c IP pole/wall mount assembly.

Figure 8 EX-4.9r-c, EX-5r-c, and EX-5r-c IP pole/wall mount

For the integrated antenna model, it is critical to mount the entire device at the predetermined location for proper path clearance to the link end. Ensure that there is adequate space around the mounting system and the radio to allow for antenna alignment for both azimuth and elevation adjustments.

Radio Ports and IndicatorsThis section provides a brief overview of the connectors, controls, and indicators on the device. Details about each item are in other sections of this document. Figure 9 shows the connectors on the r-Series radios.

Note: Mount the EX-4.9r-c, EX-5r-c, and EX-5r-c IP as close as possible to the antenna to minimize the length and associated losses of RF cabling.


50000001 212008-05-09

Figure 9 r-Series connectors

Connector OverviewThe primary user interfaces are shown in Figure 9. Table 2 provides details of the connectors. Detailed pin structures for each connector are in Interface Connections.

LED IndicatorsTable 3 provides details of the LED indicators on the r-Series radios. Note that there are two LEDs, labeled top and bottom, associated with each connector. See Alarms Page for information on how the Exalt GUI displays LED status.

Table 2 Connectors

Connector Description

GPS/RSL (1) Connection to (optional) external GPS antenna for network synchronization.

(2) Antenna alignment RSL voltage (during installation)

TDM 2&4 Ports for up to two user T1 or E1 circuits to traverse link, port numbers 2 and 4.

TDM 1&3 Ports for up to two user T1 or E1 circuits to traverse link, port numbers 1 and 3.

Power/Ethernet Connected cables traverse to the power injector (Data+Power side), and provide the following functions:

• Primary ports for user Ethernet data (10BaseT or 100BaseT) to traverse link

• DC power from power injector

(Ground) Threaded (M5) receptacle.

Use a connector cover on all unused connectors for weatherproofing. The connector covers are included in the accessory kit. Use a safety ring on each connector to secure the connector covers.


22 500000012008-05-09

RESET ButtonThere is only one external control on the r-Series radios system, a button labeled “RESET” which is located on the Power Injector. This button performs two functions: critical system parameter reset and summary alarm information.

Use the reset function if the IP address and/or passwords are lost. Use the following steps to perform a critical parameter reset:

1 Remove power from the radio by disconnecting the AC adapter from the power injector.

2 Hold down RESET button on the power injector while applying power.

Hold the RESET button down through the whole power cycle and monitor the DATA+POWER left LED on the power injector. Release the RESET button only after the LED is in the steady state (1 to 3 minutes, depending on firmware installed).

3 Release the RESET button.

The following configurations are reset on the radio:

• IP address = 10.0.0.1

• IP mask = 255.0.0.0

• IP gateway = 0.0.0.0


Table 3 LED indicatorsLocation Type Function

TDM 2&4 Green LED Solid when T1 clocking is present for input #2.

TDM 2&4Bottom

Green LED Solid when T1 clocking is present for input #4.

TDM 1&3 Green LED Solid when T1 clocking is present for input #1.

TDM 1&3Bottom

Green LED Solid when T1 clocking is present for input #3.

GPS/RSL Green LED Solid when valid GPS connection is detected.

GPS/RSLBottom

Green LED Unused.

Power/Ethernet Green LED Solid when proper power is applied.

Power/EthernetBottom

Green LED (Future implementation)

Power Injector

DATA+POWER Green LED Solid when no alarm conditions are present.

Flashing when in alarm condition.

While RESET button is pressed:

Solid when in major alarm condition (traffic affecting).

Flashing when in minor alarm condition (not traffic affecting).

Off when no alarm conditions are present.

DATA+POWERRight

Green LED Solid when proper power is applied.


50000001 232008-05-09


A flashing left DATA+POWER LED on the power injector indicates that alarm conditions exist on the radio. To access summary alarm information during normal operation, press and hold the RESET button. The following is status for the left the DATA+POWER LED while holding the RESET:

• Solid on is a link alarm (link is down or errored)

• Flashing indicates a minor alarm (does not affect traffic)

PowerThe radio requires a DC power source within specifications. DC can be provided from a DC battery source, central lab/rack supply, or from the supplied AC adapter.

Terminating the RF Connectors (EX-4.9r-c, EX-5r-c, EX-5r-c IP)Before applying power, the RF connectors must be properly terminated into a 50-Ohm load. If this is not performed, the radio may be damaged by simply applying power. Also, there are human safety factors to consider regarding potentially harmful RF radiation.

The following lists a few simple ways to achieve proper termination:

• Connect a 50-Ohm coaxial termination device to the RF port of the radio. The termination must be rated to 1W (or more). Example(s) include:

– Broadwave Technologies P/N 552-200-002, or similar

• Connect the complete transmission system. That is, the RF cabling including the antenna. The cabled antenna provides a proper termination for the RF output.

• Connect a fixed (or a series of fixed) 50-Ohm attenuator(s) to the RF connector, either directly or at the end of an RF transmission line. The attenuator must be at least 30dB as specified at the operating frequency (~4950 MHz for the EX-4.9r-c; ~5700 MHz for the EX-5r-c and EX-5r-c IP) and rated for a minimum of 1W input power. Examples include:

– Broadwave Technologies P/N 352-103-xxx

– Bird 2-A-MFN-xx

– JFW Industries 50FP-xxx-H6-N

Cover any unused connector with the connector cap and apply the weather-seal tape. Both cap and tape are included in the accessory kit.

AC PowerThe AC adapter easily connects to the power injector. Refer to the input voltage requirements stated on the label affixed to the adapter to ensure that the adapter can be used with the AC mains supply.

The AC plug outlet provided with the adapter may need to be replaced to match the country configuration. The adapter cable uses a standard connector for this cable for use of a pre-wired cable appropriate to the outlet configuration. If the appropriate cable is not available, the existing AC plug end can be severed and a replacement plug affixed. Consult a qualified electrician for this activity.

Note: Read this section completely before applying power.


24 500000012008-05-09

Do not plug the adapter into the mains power. First, verify that the RF connector is properly terminated (see Power), and then plug in the radio-side connector from the AC adapter to the radio. If the AC mains can be turned off using a switch, disable the power, plug the AC side of the adapter into the AC mains socket, and then enable power to the circuit. If the AC mains cannot be turned off, plug in to the AC main socket to apply power.

Verify that the radio is active by observing LED activity on the injector and radio. All LEDs on the radio flash at initial power cycle.

Exalt strongly recommends that the AC mains supply be fused or on a separate breaker to ensure against over-voltage and/or over-current situations and to provide some form of protection to the radio electronics and other devices connected to the same supply. In addition, if the AC power is subject to significant spikes or variation, power conditioning is a worthwhile investment, as the quality of mains power may have a direct impact on the device operation, performance and/or reliability. An Uninterruptible Power Source (UPS) or other form of battery-backed system protects against brown-out and black-out conditions, and condition the power presented to the adapter.

Evaluate the opportunity for lightning or other similar surges to be present on the powering system, including the ability for surges to couple to the power wiring system. If an evaluation indicates that there is a potential likelihood for these conditions to occur, additional surge protection is recommended for the input power wiring, especially to protect the radio electronics between the adapter and the radio’s DC input connector.

The above statement is similarly true for every wired connection to the device. While the configuration for surge suppression or line conditioning is of a different type for each kind of signal interface, the opportunity for damage to the device, loss of communications and property is significant. In some cases, there can also be a risk to human life by not protecting against lightning entering a building through wiring or improper grounding. If you do not have experience in this type of installation practice, consult a qualified electrician and/or telecoms professional during the installation and wiring of the equipment.

Power InjectorThe r-Series radios use a power injector to send DC power to the radio over the CAT5 cable, and including the Ethernet connections. Figure 10 shows the power injector connectors that connect the AC adapter (included with the system) and the radio.

Figure 10 Power injector connectors

• Connect the network Ethernet connection to the DATA connection of the power injector.

• Connect the cable for the radio to the DATA+POWER connection of the power injector.


50000001 252008-05-09

• Ground the power injector using the grounding receptacle. The injector can also be mount wall using the bottom panel brackets.

CAT5 Lightning/Surge ProtectionTo provide for human safety and for the safety of connected network equipment, it is highly recommended to place a weatherproof lightning suppression device at the egress point where the CAT5 cable(s) enter the building, shelter, or cabinet.

To protect the radio equipment, install a weatherproof lightning suppression device near the radio for all connected CAT5 cables.

For the Power/Ethernet cable, specific voltage requirements must be met. The following devices are the only devices currently recommended:

• Transtector ALPU-EXLT

• Transtector ALPU-90v

• Transtector ALPU-ALVR

Generally, use the short CAT5 cable supplied with each radio for the short connection between the radio and the first arrestor. Use bulk outdoor-rated CAT5 cable for the longer run between arrestors, and indoor- or outdoor-rated cable with a standard CAT5 termination for the connection from the egress arrestor and power injector.

If the radio arrestor is deleted from the design, Exalt resellers can supply a longer cable with the proper weatherproof connector for the connection from the radio to the egress arrestor.

Apply this same method for the TDM connections. There are no special requirements for lightning arrestors. Vendors, such as Transtector and Polyphaser, offer single and multiple TDM weatherproof arrestors. Note that each connector on the radio can carry up to 2 TDM (Time Division Multiplexing) connections.

Reset to Critical Factory SettingsIf necessary, the radio terminal may be reset to critical factory settings. This may be necessary if the IP address and/or passwords for the system are not known. All other configurations are left at their current settings. If a complete default factory configuration is desired, load the Default Configuration File into the system, as described in System Configuration Page.

The following parameters are configured after a reset to critical factory settings:

• IP Address = 10.0.0.1

• IP Mask = 255.0.0.0

• IP Gateway = 0.0.0.0


Note: For legacy models only, all CAT5 cables must be purchased from an Exalt authorized dealer. This is due to the use of a custom weatherproof connector.

For standard models, use only outdoor-rated UV-resistant CAT5 cable. This cable must have an outer diameter between 0.25"/6.35 mm and 0.31"/7.87mm. Belden 1300A is recommended. Securely hand-tighten all connectors on the ODU to ensure a weatherproof seal.


26 500000012008-05-09


Antenna/Transmission SystemThis section provides guidance to mounting and connecting the RF transmission system, which consists of the antenna, RF cabling, and RF lightning arrestors. Consult the manufacturer’s instructions for proper mounting, grounding, and wiring of these devices, and for definitive direction. These manufacturer’s instructions supersede any information in this section. See Table 7 for a list of supported antennas.

Initial Antenna Mounting (EX-4.9r-c, EX-5r-c, and EX-5r-c IP)The antenna must be an exact model recommended by the path and site planning engineer(s). Mount the antenna at the proper height, mast/mounting location and polarization orientation as determined by the path and site planning engineer(s). The model type, location, and orientation of the antenna is critical with respect to achieving proper path clearance, as well as to mitigate external or self-interference from nearby or collocated systems operating in or near the same frequency band.

The antenna structure must be secure and safe with respect to the mounting of the antenna, transmission system weight, radio housing, and the combined weight of any personnel that may climb or attach to the structure.

The combined weight of items and forces on the structure must be carefully considered in the design and construction of the structure. This must include the weight bearing on the structure in the highest wind conditions possible in the region, and with respect to all objects affixed to the structure.

If additional objects are affixed to the structure in the future, it may be important to evaluate both the mechanical impact of these planned additions (with respect to wind and weight loading), as well as the potential impact to RF interference and frequency coordination (if additional radio equipment is anticipated). This is especially important if future equipment is likely to operate within the same frequency band.

Once the antenna is mounted, cabled, and aligned, your goal is to never require modification. This prior planning is important in the path and site planning stages and in construction of the antenna structure.

Follow the antenna manufacturer’s instructions for mechanical mounting of the antenna. Ensure that there is enough room around the antenna for alignment activities (moving the antenna in vertical and horizontal arcs), and for the RF transmission line to connect to the antenna connector unobstructed and within the specified bend radius requirements of the transmission line.

At this point, the antenna mounts should be fully secure to the structure, the feed of the antenna securely mounted to the antenna (if the feed is a separate assembly), and the azimuth and elevation adjustments not completely tightened in preparation of the antenna alignment activity. It is a good practice to connect the transmission line to the antenna connector as early in the process as possible, to reduce the opportunity for debris or moisture to enter either the antenna connector or the transmission line connector. Use a connector cover or other temporary measures to ensure that the connector is kept clear. Take extra care if the antenna is installed during inclement weather to ensure that no moisture gets inside the antenna connector at any time.

Warning! Mount the antenna in a restricted area and in a manner preventing long-term human exposure to the transmitted RF energy. To comply with FCC and Industry Canada regulations, the minimum safe distance from the antenna for continuous human exposure is 10'/3m.


50000001 272008-05-09

Now the antenna can be aimed in the general direction required for the link. Use a compass, a reference bearing, binoculars or any other similar device to point the antenna in the direction (generally) of the far end radio, and then slightly tighten the azimuth and elevation adjustments so that the antenna maintains its general position and is safe to be left without additional securing. Refer to the Exalt white paper, Antenna Alignment, for more information on antenna alignment techniques.

Transmission Line from Antenna to Radio (EX-4.9r-c, EX-5r-c, and EX-5r-c IP)Most installations use a very short length of coaxial transmission line for the connection between the antenna and the radio device. Coaxial transmission line can either have a solid or braided shield. Solid-shield cables are more resistant to external signal coupling and interference, but are generally stiffer than braided cables. Consult the path or site engineer(s) to ensure that the proper materials are chosen for the installation and that all factors were considered.

Generally, the larger the diameter of the transmission line, the lower the loss. So for longer runs of transmission line, larger diameter cables are highly advised. However, at every frequency, there is a maximum diameter cable that supports the operating frequency. Verify the specifications. This should is determined in the path and site planning process.

Table 4 lists representative samples of transmission line types recommended for the Exalt Digital Microwave Radio.

It is critical that the transmission line and antenna be capable of supporting the same type of connector, or easily adapted. It can be important to minimize the number of connectors and adapters, and it is ideal that they match directly without adaptation. In most cases, transmission line allows for N-type male connectors and antennas have N-type female connectors.

If possible, connect the primary transmission line directly to the antenna. It is desired to have the fewest possible pieces of transmission line in the system, to minimize losses and points of failure from connectors. The antenna can typically accommodate a direct connection if planned in advance. Use a 90º adapter for the connection to the antenna, if necessary, but confirm that all connectors and transmission lines are properly specified for the operating frequency with minimum loss, proper impedance (50 Ohm) and proper VSWR characteristics.

Transmission line connector termination is a critical element of the installation. Many ‘factory built’ RF transmission lines do not provide the proper characteristics for proper transmission, despite their published specifications, often due to the fully or semi-automated process of factory termination, which may not have considered the frequency of your system. When buying pre-terminated transmission line, it is strongly advised to obtain the documentation of test measurements on the

Table 4 Recommended transmission line

Manufacturer Type Description Loss at 4.9GHz Loss at 5.3GHz Loss at 5.8GHz

Andrew LDF4-50 1/2-inch solid shield 5.6dB/100' 5.7dB/100' 6.0dB/100'

Andrew LDF4.5-50 5/8-inch solid shield 4.3dB/100' 4.4dB/100' 4.7dB/100'

Times LMR-600 1/2-inch braided shield 6.8dB/100' 6.9dB/100' 7.3dB/100'

Times LMR-900 5/8-inch braided shield 4.5dB/100' 4.6dB/100' 4.9dB/100'

RFS LCF12-50J 1/2-inch solid shield 5.5dB/100' 5.6dB/100' 5.9dB/100'

RFS LCF12-58J 5/8-inch solid shield 4.4dB/100' 4.5dB/100' 4.8dB/100'


28 500000012008-05-09

connected transmission line showing that the loss characteristics and VSWR are within the specified limits specifically at your operating frequency. In addition to factory-built transmission line, self-terminated transmission line can suffer the same issues.

The manufacturers of transmission line typically offer instruction and certification for transmission line termination, and may also provide videos illustrating the process. There is no amount of extra care, education, precision, and effort that can be overstated for this process.

There is often a need for a small excess of transmission line near the antenna to accommodate both the need for extra slack as the antenna is loosened and moved for the alignment process, and to accommodate a drip loop for the transmission line and the initial transmission line securing hardware and grounding near the antenna. In addition, the transmission line is typically very stiff, and can provide undue pulling force on the antenna or radio connector. Take care to align the cable with the connector so that it does not provide any torque or strain on the connector.

Consult your transmission line manufacturer for the proper transportation, hoisting, securing, and grounding process. Always be very mindful of the entire length of transmission line to ensure that the transmission line is never twisted, kinked, or over-bent beyond the specified bend radius. Once a transmission line is over-bent or kinked, it will likely never recover its specified characteristics, even after straightening, and will often be completely unusable.

The opposite end of this primary transmission line typically terminates at the radio connector. If using a long transmission line (in excess of 3'/1m), an RF lightning arrestor is recommended to protect the radio equipment.

As soon as practical, weatherproof the connected ends of the transmission line to the antenna and lightning arrestor and radio. This process should be delayed as long as possible to ensure that all systems are working properly before applying the weatherproofing. Once weatherproofing is applied, it may have to be removed for testing or installation modification. With this in mind, if the installation is occurring during inclement weather, take extra care at all times to ensure that no moisture enters any connector at any time. If moisture is suspected to have compromised the antenna or transmission line, it may render those devices useless without any means for remedy except for full replacement.

Cap and weatherproof the second antenna connector on the radio if using a single-polarity antenna.

Indoor MountingOn rare occasions the antenna can be mounted indoors behind a window. In these cases, there would not be a need for drip loops or an RF lightning arrestor. Use a very short transmission line connected directly between the antenna and the radio mounted nearby. The weatherproofing process can also be omitted.

RF Lightning ArrestorRF lightning arrestors provide a direct path to ground for lightning strikes that may couple to or directly hit the outdoor transmission system or antenna structure. The RF lightning arrestor prevents any associated voltage and current from entering the radio equipment, other equipment, or humans.

The following lightning arrestors are examples of proper devices for Exalt Digital Microwave Radios:

• Polyphaser AL-LSXM

Caution: Always follow the manufacturer’s termination process EXACTLY, and only use the manufacturer’s authorized tools and connectors for a given transmission line type.


50000001 292008-05-09

• Andrew BB-BNFNFE-26

Mount and ground the RF lightning arrestor in accordance to the manufacturer’s recommendations. Place it as close as possible to the radio equipment. Minimize the distance to the radio to lessen the opportunity for lightning to couple to or strike the unprotected section of transmission line (if any). Consult a qualified electrician or installer in all cases of grounding and lightning arrestor implementation.

Antenna AlignmentAntennas must be installed at both ends of the planned link to commence precision alignment. Refer to the Exalt white paper, Antenna Alignment. The r-Series radios have an integrated antenna.

Antennas are typically aligned using the radio hardware for precise alignment. However, there are many very useful tools available to aid in this process, inclusive of devices specifically designed for the purpose of aligning antennas. Some examples are:

• XL Microwave Path Align-R

• Teletronics 17-402

Use of these devices may be extremely advantageous as compared to using the radio, because they employ many unique facilities to aid in this process. Using these tools also makes it possible to align the antennas before the radio equipment is delivered. However, many installers successfully use the radios as the means for antenna alignment.

The following are the primary facilities when using the radio to align the antenna:

• RSL voltage connection using a volt meter (recommended)

Insert the included adapter into the GPS connector on the radio housing and the opposite end connected to a volt meter.

The RSL test point DC voltage is inversely proportional and numerically calibrated to the received signal level. The voltage rises as the antennas are less in alignment, and falls as antennas are more in alignment. The voltage measurement corresponds to the received signal level in measurements of dBm (a negative number for RSL measurements). For example, an RSL of -60dBm yields an RSL voltage measurement of 0.60VDC; an RSL of –45dBm measures 0.45VDC.

• Audio alignment buzzer

Enable the audio alignment buzzer through the Exalt GUI. When enabled, the radio enclosure emits a sound. The pitch rises when higher (better) levels of RSL are achieved. Align the antennas until the highest pitch is accomplished. The tone is continuous when the two ends of the radio system are in communication. Otherwise, the buzzer beeps.

• Exalt GUI RSL reading indicates the current RSL in dBm.

Note: There is a slight delay in RSL readings in the GUI as the RSL levels change. In this case, fine alignment can be done in small adjustments allowing a small gap of time so that the impact of the adjustment on the GUI display catches up to real time.

Note: Only use the browser-based GUI for antenna alignment if there are no other means available. If this method is required, refer to Exalt Graphical User Interface (GUI). The RSL reading can be read on a PC or any handheld computing device that supports an HTML browser and Ethernet connectivity.


30 500000012008-05-09

Configuration and ManagementThis section describes the command line interface (CLI) and Exalt graphical user interface (GUI).

Telnet into the Command Line Interface (CLI)Use a Telnet connection to access the CLI in the Exalt Digital Microwave Radios. Use the CLI to set key parameters on the system.

Connect to the Radio in a Telnet Session

Make the Telnet connection to the radio through the Ethernet port. Use Windows and perform the following steps:

1 Open a command prompt or MS-DOS prompt (Start>Run).

2 Type C:\>Telnet <IP Address> at the command line:

The default IP address is 10.0.0.1

TelnetUse Telnet when prompted to enter the administration level login and password. The default administration login is admin and password is password. It is recommended that the default administration password be reset by performing a radio reset (see Reset to Critical Factory Settings).

Figure 11 shows the three menu choices available after log in.

Figure 11 CLI main menu

Select 1 or 2 to display the Configuration or Status menus, respectively. Select 3 to exit the session. The following selections can be made on all screens:

• 0 = back to previous screen

• 9 = help

• Ctrl+\ (control and backslash keys) = exit session

Exalt Graphical User Interface (GUI)The Exalt GUI is the primary user interface for configuring and troubleshooting the radio and radio system. A computer or hand-held device with a conventional HTML browser and Ethernet port is required. Microsoft Internet Explorer is the preferred browser. Netscape, Mozilla, and Firefox are also supported.

Note: The accessing computer must be on the same IP subnet as the radio.


50000001 312008-05-09

Preparing to Connect

If the radios are new, both radios are preconfigured as Radio B, and have the same IP address. The initial priority is to configure one radio to Radio A and assign different IP addresses, unique to each radio. There are two ways to change the IP address:

1 Reset the radio to the critical default factory settings (see Radio Reset).

2 Connect to the GUI using the default IP address (10.0.0.1), and change the IP address through the GUI interface.

To configure a radio as Radio A, connect to the GUI and change the configuration, as discussed in this section.

Make Connections

It is recommended that one radio at a time be configured, on a bench, before taking the radios to the field for installation:

• (EX-4.9r-c, EX-5r-c, and EX-5r-c IP only) Terminate the RF connector with a 50-Ohm termination or a fixed attenuator of at least 20dB (see Power).

Once connected to the radio using Ethernet, log in to the Exalt GUI.

Log In

Use the following steps to log in to the Exalt GUI.

1 Open a browser window.

Microsoft Internet Explorer is the recommended browser. Netscape, Mozilla, and Firefox are also supported. If there are issues with your browser, please report it to Exalt Customer Care. You may be required to use a different browser to immediately overcome issues.

2 Type the IP address of the radio in the address bar.

Note: To connect to the radio’s Ethernet port and use the GUI interface, the accessing computer must match the radio’s IP address subnet. It is therefore necessary to either change the radio’s IP address through the CLI to match the subnet of the computer, or change the computer’s IP address to match the subnet of the radio (such as, a computer IP address of 10.0.0.10 if trying to connect to a radio set to the factory default IP address of 10.0.0.1).

Note: Do not connect the radios in a back-to-back configuration. If the radios are set to their factory default settings, both radios are configured as Radio B and cannot communicate. Both radios also have the same IP address, which causes IP address conflicts

Note: The IP address subnet of the accessing computer must match the radio’s IP address subnet to connect using Ethernet.


32 500000012008-05-09

Figure 12 Initiating the browser connection

The following window displays after pressing the Enter key or clicking the Go button in the browser window.

Figure 13 Browser Login screen

Login Privileges

There are two levels of login privileges:

• Administrator (admin) – assigned complete permissions to view, edit, and configure

• User (user) – assigned limited, view-only permissions with no edit or configuration rights

The default login names and passwords are as follows:

Administrator login credentials are required for configuration purposes. Type the user name and passwords for Administrator level and click OK. The following screen displays.

Table 5 Default login information

Privilege level User name Default password

Administrator admin password

User user password


50000001 332008-05-09

Figure 14 Radio Information page

Quick StartTo establish a link on the bench, apply the following basic configurations to the radio terminal. Use the steps in the Quick Start Guide included with the radio. A summary of the items that need to be configured are:

• Radio IP address for each end.

– Each end must have a different IP address and cannot match the accessing computer’s IP address or any address assigned if radios are part of a larger network.

– It may be required to change the IP address of the accessing computer after changing the IP address of the radio so that the IP subnet matches.

– The radio IP address is listed on the Administration Settings Page.

• Install the Regulatory Domain Key (RDK) for RDK-enabled radios only.

– The radio is non-functional without the RDK.

– RDK is entered on the Administration Settings page.

– RDK references the unit’s serial number and the country/region where the radio will be deployed.

– RDK is obtained through your Exalt Authorized reseller or distributor.

• Set one radio as Radio A.

– The radio selected as Radio A must be configured.

– Radio A/B selection is the Endpoint Identifier parameter on the System Configuration Page.

– Even though both radios are set as Radio B by default, confirm this configuration on the radio intended to be Radio B.


34 500000012008-05-09

If all other parameters are still configured at their factory default settings, the radios can now be connected back-to-back to verify that the link is communicating and perform any other desired tests. See Back-to-back Bench Testing for test information.

Navigating the GUI describes each page of the GUI. Most configuration parameter settings are intuitive. The following link parameters must match at both ends for the link to communicate:

• Link Security Key (Administration Settings Page)

• Bandwidth (System Configuration Page)

• RF Frequency (System Configuration page)

• Link Distance (System Configuration page)

• TDD Frame Size (System Configuration page)

Navigating the GUIThe GUI provides the primary interface for all configuration and management. There are three sections of the main GUI window:

• Summary status information section (upper-left corner)

• Navigation panel

• Main window

Figure 15 Exalt GUI window description

Summary Status Section

This section of the Exalt GUI provides a review of the system status.

In the screens in Figure 15, the top bar illustrates the alarm condition of the link. The information inside the bar is equivalent to the entry of the Link Name set by the administrator in the Administration Settings Page.

Note: Changing any of these parameters causes a temporary loss of link. The GUI displays a warning and provides an opportunity to cancel changes.

SUMMARY STATUS

NAVIGATION PANE

MAIN WINDOW


50000001 352008-05-09

The color of the panel indicates alarm status:

• Green indicates the system is communicating and all functions are normal

• Yellow indicates a minor non-traffic affecting alarm condition

• Red indicates a major traffic affecting alarm condition

The left panel summarizes the alarm conditions of the local radio (the radio that matches the IP address). The information displayed is the IP address and the endpoint identifier (Radio A or Radio B). The right panel summarizes the alarm conditions of the remote radio (the radio linked to the local radio).

The Summary Status Section allows the Exalt GUI to be a rudimentary management system. Minimize the browser window to display just the top bar or the top bar and radio information, and open several browsers on the desktop. When a window status changes to yellow or red, you can quickly maximize that window to determine the issues.

Figure 16 Summary status information

Navigation Panel

In the navigation panel, pages with sub-pages have a plus (+) to the left of the page link. Click the plus sign or page name title to view sub-page titles. The pages can be collapsed to hide the sub-pages when a minus (–) sign appears to the left of the page link.

Management pages are indicated with an X to the left of the page name. Click the X or page name to display the page within the main window.

Note: The ‘local’ radio might be the near-end or the far-end radio, depending on the management interface connection. The terms local and remote refer to the orientation of the radio terminals relative to the IP address you are managing. When making certain changes to a near-end radio without first making changes to the far-end radio, the link may become disconnected unless configuration changes are reverted to their original settings. When making changes that may disrupt the link, always change the far-end radio first, and then the near-end radio to match.


36 500000012008-05-09

Note: The ‘local’ radio might be the near-end or the far-end radio, depending on the management interface connection. The terms local and remote refer to the orientation of the radio terminals relative to the IP address you are managing. When making certain changes to a near-end radio without first making changes to the far-end radio, the link may become disconnected unless configuration changes are reverted to their original settings. When making changes that may disrupt the link, always change the far-end radio first, and then the near-end radio to match.


50000001 372008-05-09

Radio Information PageThis page provides general information about the local radio terminal. This information is helpful for troubleshooting and for record keeping.

Figure 17 Radio Information page


38 500000012008-05-09

Administration Settings PageThis page allows contains general parameters for the radio system. The Current Value column lists entries actual settings. Desired changes are entered in the New Value column.

After all desired changes are entered, click the Update button to accept and enable changes.

Figure 18 Administration Settings page

Most entries on this page are self-explanatory. The following lists unique or important parameters.

• Fill in the date and time fields as soon as practical. Events are captured with time/date stamps, which is valuable information for troubleshooting.

• Set the Link Security Key to something other than the factory default setting (12 characters, all zeros) at each end. The link security key must match at both sides of the link. If the security key remains at the factory setting, the radio link is open to sabotage by a party with the same radio model. Each link should have a unique security key. If using the same security key for every link in the network, the radio could link to any other radio with the same security key. This is problematic in multi-radio networks.

– Note that the security key must be exactly 12 characters. Any printable ASCII character can be used. The link security key is case sensitive.


50000001 392008-05-09

– Reset the admin and user passwords. These passwords should not match. If the admin password remains at the factory default setting, it provides an opportunity for random reassignment by a network-connected user.

– The new password must be entered twice. If the passwords do not match and the Update button clicked, the password is not changed and remains set to the previous password.

• Enter the license key provided by Exalt to access extended features or diagnostic capabilities. Click Update to accept the changes and enable the new features. License keys are issued by radio serial number, so ensure that the license key used was issued for this particular radio.

• The Regulatory Domain Key establishes the frequency bands, tuning frequencies, bandwidths, output power and Dynamic Frequency Selection (DFS) requirements, in accordance with the regulations that apply in the country where the product is deployed. The RDK must be typed in to enable ANY functionality for the radio. The RDK is issued to the Exalt Authorized distributor or reseller, and is paired to the specific serial number of the radio.

• AES Advance Encryption Standard) can be implemented to provide additional data security for the wireless link. This function requires an upgrade license key (purchased separately). Both radios in the link must have a valid AES upgrade license key to implement AES. Different bit-length encryption license keys (for example, 128-bit and 256-bit) are also available, depending on model type. If the required upgrade license key is present, simply insert a matching ASCII string on both terminals and select the Enable AES On option for AES encryption. Note that similar to the administration and user passwords, the AES string must be entered twice for each terminal.

Note: Changing the link security key interrupts transmission until the opposite end is changed to match. Always change the far-end radio first, and then change the near-end radio.


40 500000012008-05-09

Simple Network Management Protocol (SNMP) ConfigurationUse SNMP to manage networked devices and execute the following functions:

• GET: Obtain information from the device, such as a configuration setting or parameter.

• SET: Change a configuration setting on the device.

• TRAP: The device proactively informs the management station of a change of state, usually used for critical alarms or warnings.

Figure 19 SNMP Configuration page

One feature of the SNMP implementation is that system configuration changes do not take effect using the SET command. Instead, groups of configuration settings can be preconfigured for global change, and a single ‘Save’ (Commit) command implements all changes.

When some parameters are changed, a link may drop and/or management control lost. MIB files allow many parameters to be set at once, allowing only a temporarily dropped link or management control issue. The opposite end radio can be quickly reconfigured, with little downtime for the link and management control. The save (Commit) command is similar to the Update button.

Dropped links or management control issues do not occur with every parameter change. Many configuration changes do not impact traffic or management access.

EX-series radios utilize SNMPv3, a high security version of SNMP, to ensure secure access to and storing of management data. The SNMPv3 security string matches the admin and user passwords. Passwords must be eight characters or longer.

Note: Currently the SNMP implementation does not support TRAP functions. For critical alarms, use the GET command for specific alarm conditions.


50000001 412008-05-09

The SNMP MIBs are organized similar to the GUI. Become familiar with the GUI before using the SNMP function.

SNMP v1/v2c/v3 Support Options

Enable the SNMPv1/v2c options to allow entering read and read/write community strings.

Enable the SNMPv3 options to allow entering read and read/write user names and passwords. These entries are de-coupled from the standard radio user names and passwords. SNMPv3 provides full management security.

Note: Currently not all EX-series radios implement SNMP. Check the software release notes to verify that the function is available. Generally, the radio supports SNMP when MIB files are listed on the File Activation Page.

Note: Users are encouraged to avoid enabling SNMPv1/V2c support due to known security loopholes in these protocols.


42 500000012008-05-09

System Configuration PageThis page contains several critical system parameters.

Figure 20 System Configuration page

Most entries on this page are self-explanatory. The following lists unique or important parameters.

• Set the Endpoint Identifier so that one end of the link is set to Radio A and the opposite end set to Radio B. In single-link networks, it is unimportant which end is designated A or B. In multi-link networks, however, it may be important to orient the links so that at any collocation site (where there are multiple radios of the same type at the same site), all radios are set to the same Endpoint Identifier (A or B). See Link Orientation and Synchronization.

• Set the Radio Transmit Power (dBm) parameter to the designed level. The professional installer sets this value or dictates the value of this setting to the system administrator following the system

Note: For models requiring a Regulatory Domain Key (RDK), you must enter a valid RDK to edit this page.

Note: Changing the Endpoint Identifier parameter requires a reboot of the radio to take effect. The reboot temporarily interrupts traffic.


50000001 432008-05-09

design and local regulations. In many cases, this value must be set to a proper value to comply with legal restrictions. Improper values can result in liability to the user and/or installer.

– Do not adjust the Radio Transmit Power parameter to a value higher than is legally allowed.

– Do not adjust the Radio Transmit Power parameter lower than the link budget and fade margin can afford.

• Set the Bandwidth (MHz) parameter to the designed level. The value of this is determined in the design/engineering stage. The Bandwidth parameter must also match at both ends of the link. In conjunction with the Mode parameter, the Bandwidth parameter directly relates to the capacity, latency, and the number of TDM circuits supported. The transmitter and receiver bandwidth are modified using this parameter, making it critical that it be set with respect to the local RF noise and interference profile, and/or in relation to any multi-link network design.

• Set the Mode parameter to the designed selection. The value of this setting is determined in the design/engineering stage. The Mode parameter must match at both ends of the link. In conjunction with the Bandwidth parameter, the Mode parameter setting directly relates to the capacity of the system, as well as critical RF parameters, including receiver threshold, carrier-to-interference ratio, and in some cases, maximum radio transmit power.

• Set the RF Frequency (GHz) parameter to the designed point. The value of this setting is determined in the design/engineering stage. RF Frequency must match at both ends of the link. It

Note: Changing Radio Transmit Power may temporarily interrupt traffic. Small changes in output power do not normally interrupt traffic, but larger changes may.

Note: The link may be lost and unrecoverable through GUI control. If the link is lost due to reduction of Radio Transmit Power, travel to the radio location(s) may be required to reset the value.

Note: Changing Bandwidth will temporarily interrupt traffic. The Bandwidth parameter must match at each end. Adjust the far-end radio first, and then the near-end radio. Changing Bandwidth changes the radio’s threshold. A narrower bandwidth has better threshold performance and improved interference immunity, therefore if changing to a wider bandwidth, there is an opportunity that the link may be lost and unrecoverable through GUI control. Check the available fade margin and interference profile to determine if the impact to threshold and increased bandwidth is acceptable to maintain the link and the desired performance. If the link is lost due to increasing the Bandwidth parameter, travel to the radio location(s) may be required to reset the value.

Note: Changing Mode will temporarily interrupt traffic. The Mode setting must match at each end. Adjust the far-end radio first, and then the near-end radio. Changing Mode changes the radio’s threshold, carrier-to-interference ratio, and also may have impact on the Radio Transmit Power. A lower mode has better threshold performance and carrier-to-interference ratio, and in some cases, higher output power, therefore if changing to a higher mode (for example, from Mode 1 to Mode 2), there is an opportunity that the link may be lost and unrecoverable through GUI control. Check the available fade margin and interference profile, and determine if the impact to RF performance is sufficient to maintain the link and desired performance. If the link is lost due to increasing the Mode parameter, travel to the radio location(s) may be required to reset the value.


44 500000012008-05-09

may be critical to set RF Frequency with respect to the local RF noise and interference profiles, and/or in relation to any multi-link network design.

The frequency selection section includes the ability to select from either the complete list of frequencies (“All”) that can be tuned for the selected band and bandwidth, or, in some cases, a pre-selected list of non-overlapping center frequencies (“Preferred”) that Exalt determined provides the most flexible collocation opportunities for large networks of Exalt radios

The frequency selection section includes a band selection button that must be enabled for the frequency band of operation for which the link was engineered. In some cases, some bands may not be selectable due to regulatory constraints. Some bands also require Dynamic Frequency Selection (DFS), based on the active RDK. DFS is automatically enabled for these bands and is selectable for all other bands.

• DFS is automatically enabled for any band where required based on the regulations that match the active RDK. For bands where DFS is not required, it can still be selected. For DFS to operate properly, set the antenna gain figure to match the installed transmission system gain (that is, the gain of the antenna minus all losses between the radio and the antenna).

• Set the Link Distance (miles) parameter to the range that is equal to or greater than the actual link distance. The value of this setting is determined in the design/engineering stage.

• Set the TDD Frame Size (ms) parameter to the designed level. The value of this setting is determined in the design/engineering stage. The TDD Frame Size parameter must match at both ends of the link. The TDD Frame Size parameter setting directly relates to the capacity, latency, and number of TDM circuits that can be supported over the given link distance. In multi-link networks, especially where there are collocated links, it is also important to set all radios to the same TDD Frame Size setting to avoid self-interference. Future enhancement: The GPS or

Note: Changing RF Frequency will temporarily interrupt traffic. The RF Frequency parameter setting must match at each end. Adjust the far-end radio first, and then the near-end radio. If the RF Frequency parameter is changed to a frequency with interference, the link may be lost and unrecoverable through GUI control. If the link is lost due to changing the RF Frequency parameter, travel to the radio location(s) may be required to reset the value.

Note: When DFS is enabled, the radio temporarily stops transmitting for at least 60 seconds to ensure that no radar interference is present. This is called "Channel Availability Check (CAC).” The DFS status displays on the

. Once CAC passes, the radio resumes normal operation. If at any time during CAC or regular operation a qualifying radar signature is detected, the radio shuts down communications for a minimum of 30 minutes. This is the Non-Occupancy Period (NOP). Transmission only resumes after the NOP completes and then only after a successful CAC.

Note: Changing the Link Distance parameter will temporarily interrupt traffic. The Link Distance setting must match at each end and must not be less than the actual link distance. Adjust the far-end radio first, and then the near-end radio. If the Link Distance parameter is changed to a setting less than the actual distance, the link may be lost and unrecoverable through GUI control. If the link is lost due to this situation, travel to the radio location(s) may be required to reset the value. If the Link Distance parameter setting is set to a distance unnecessarily higher than the actual link distance, the radio may have substantially reduced performance with respect to throughput and latency.


50000001 452008-05-09

internal sync function may be necessary for these networks. See Time Division Duplex (TDD) Factors and Link Orientation and Synchronization for more information.

• Set the TX/RX Throughput Ratio (%) parameter to program radio symmetry. The default setting is 50/50 for symmetrical, full-duplex throughput. Other throughput ratio options are 20/80, 80/20, and 65/35, 35/65. See Link Symmetry.

• For asymmetric throughput, only TDD frame size settings of 2ms and 5ms and RF Bandwidth settings of 16MHz and higher are supported.

The 64MHz/Mode2 configuration does not support asymmetry due to capacity limitations of the 100BaseT interface. Set the Radio Collocation parameter to control parameters related to the GPS Synchronization feature (see Radio Synchronization).

This parameter can be enabled when an Exalt GPS receiver is connected to Radio A. There are two additional features:

– Set the Flywheel Period parameter to ‘Normal’ (default) or ‘Infinite.’ This is the period of time that the radio will run on the internal timing signal if the GPS timing signal is lost.

– The Normal parameter is a time period that allows the GPS timing signal to be recovered. The default time to wait is set between 5 and 10 min. The system then resynchronizes to the GPS signal without impact to traffic. If Normal is selected and GPS timing is not recovered within the set time period, the system stops transmitting (loss of link) until GPS timing is recovered. This prevents self-interference to local systems, but loses the link.

– The Infinite parameter allows the radio to run on the internal clock source with no limit and attempts to resynchronize with GPS when the GPS timing source is detected. This allows the link to continue to operate, however, if a GPS signal is not detected within approximately 10 minutes, the radio may start to cause interference to other collocated systems, and other collocated systems may start to cause interference with it. If after this interval GPS timing is restored, a temporary outage due to the resynchronization requirement may occur.

– Set the Tx Timing Offset (uSec) parameter to allow the administrator to delay transmitter timing from the GPS timing pulse by a fixed time, in microseconds. This is useful if multiple GPS-synchronized Exalt radio systems are present, separated by distance, such as when using a repeater. This delay is required to offset the difference in speed-of-light between the two locations. It is recommended to add a 5uSec delay for every mile of difference in path length. For example, if there is one link with no delay, delay the link within the field-of-view of the first link on the same or overlapping frequency channel accordingly so that it is synchronized, including the speed-of-light delay between the two sites.

• Antenna Port parameter

– EX-4.9r, EX-5r, and EX-5r IP: The antenna port selection toggles between the vertically and horizontally polarized integrated antennas. Ensure that both link ends match polarization.

– EX-4.9r-c, EX-5r-c, and EX-5r-c IP: The antenna port selection allows selection of either the ANT 1 or ANT 2 connector (or the A or B connector on Legacy models) on the front face of

Note: Changing the TDD Frame Size parameter will temporarily interrupt traffic. TDD Frame Size parameters must match at each end. Adjust the far-end radio first, and then the near-end radio. If the TDD Frame Size parameter is set to a value that cannot be supported for the link distance, the link may be lost and unrecoverable through GUI control. If the link is lost due to this situation, travel to the radio location(s) may be required to reset the value.


46 500000012008-05-09

the radio housing. Only set this parameter if using a dual-polarized antenna or two separate antennas.

• Buzzer Timeout (minutes) parameter creates an audio signal for antenna alignment. Turn on the buzzer continuously during antenna alignment or preset a period of time that the buzzer will sound. If the buzzer stops before alignment activities are complete, change the selection and press the Update button or select the ON option until alignment activities are complete.

Note: Changing the antenna port will temporarily interrupt traffic. The polarization of the antennas at each end must match at each end – adjust the far-end radio first, then the near-end radio.


50000001 472008-05-09

Ethernet Interface Configuration PageThis page allows the administrator to set the alarm, and duplex settings of the Ethernet connection.

It also allows determination of the management information for in-band (carried over the air and available from both the MAIN and AUX connectors on either end of the link) or out-of-band (not carried over the air and only available from the local AUX connector)

Figure 21 Ethernet Interface Configuration page

To ignore Ethernet alarms, disable the alarming of the MAIN and/or connector. Muting the MAIN connection is desirable when connected equipment senses Ethernet signaling and makes decisions (such as, spanning tree protocol enable) based on the Ethernet signal. If the MAIN connection has muting enabled, the port is muted when the link is not active.

It may be desirable to disable the alarming of the AUX connector if it is not used.

Set the Ethernet interfaces on the radio and connected equipment to 100/full-duplex for best performance. If the Ethernet ports are set to auto-negotiation, poor throughput performance may be a result, as well as intermittent disconnections of the Ethernet connection.


48 500000012008-05-09

VLAN Configuration PageVLAN is disabled as the default setting for Exalt radios. The Exalt radios still pass VLAN and non-VLAN traffic across the link, but do not examine the VLAN traffic or act upon it. Enable VLAN using the Exalt GUI for expanded VLAN support.

Figure 22 VLAN Configuration page

When VLAN is first enabled, the Ethernet interface port is assigned as Default VLAN, until the port is configured with specific VLAN IDs. For example, a specific VLAN for management access to the radio must be manually configured.


50000001 492008-05-09

If any VLANs are configured in addition to the management VLAN, the radio automatically discards traffic that not matching a configured VLAN. Non-tagged traffic, or traffic with tags matching VLANs that are not configured, do not flow across the radio link.

Up to 16 unique VLANs can be configured. VLAN ID numbering ranges from 1 to 4094. The Native (default) VLAN ID can be changed from the default setting. Every configured VLAN can also have a logical name to help track the function of each VLAN.

VLAN configurations are maintained even when VLAN is disabled. That is, the VLANs can be configured and the configuration saved, even though they are not active until VLAN is enabled. Use the procedure in Reset to Critical Factory Settings to restore the management connection if a mistake was made assigning the management VLAN and access cannot be restored.

Note: Once a management VLAN is configured or modified and the Update button clicked, the management connection will likely be lost. The management connection to the radio must follow the configuration to the assigned VLAN. After configuring and enabling the management VLAN on the radio, reconfigure your network’s management access to match the settings on the radio.

Note: Only one entry per VLAN ID is allowed. If the same VLAN ID is entered into the table more than once, the radio uses the first assignment found in the table and ignores duplicate entries.


50 500000012008-05-09

T1/E1 Configuration PagesThese pages allow the administrator to selectively enable or disable the T1 or E1 circuits, one at a time. For enabled T1/E1 circuits, additional configuration, including loopback functions, are available. Disable the unused T1 or E1 so that the alarms are turned off and more throughput is allocated to the Ethernet interface. Every enabled T1 or E1 input, even if there is no T1 or E1 signal present, reduces the aggregate throughput of the Ethernet interface by roughly 3Mbps (for T1) or 4Mbps (for E1).

This page toggles between T1 and E1, as required, by clicking the Set to T1 or Set to E1 button. A warning displays that a reboot is necessary, and the radio reboots if the administrator continues. This will interrupt traffic. It may be necessary to re-login to the radio after the reboot completes. T1/E1 mode self-coordinates across the link if the link is active. This means that it only needs to be set while connected at one end. In addition, enabling and disabling T1/E1 circuits also self-coordinates across the link if the link is active. If a link is not active and T1/E1 enabling is a mismatch when a link is first created, the Radio A configuration for T1/E1 enabling supersedes the settings on the Radio B configuration, and changes the settings on Radio B.

T1 Interface Configuration Page

This page allows the administrator to enable/disable each individual T1 channel, set the Line Build Out (LBO), Line Code (either AMI or B8ZS), and AIS enabling/disabling for each input. If enabled, the radio places an AIS code on the output of the associated interface if and when the link fails or when there is no T1 signal available from the far end to provide the user at the local end. Loopback controls are also provided (see T1/E1 Loopback).

Note: Certain combinations of the TDD Frame Size, Link Distance, Mode, and Bandwidth parameter settings limit the number of T1/E1 circuits that can be carried by the radio. In these cases, certain fields on the T1/E1 Interface Configuration pages are not available, starting with the highest port number. For example, for a 4x T1/E1 radio version, if only three (3) circuits can be carried, port 4 is not available for configuration and is disabled. If only two circuits can be carried, both ports 3 and 4 are not available. Increasing the TDD frame size and Mode parameters, and/or increasing the Bandwidth parameter results in an increase in the supported number of T1/E1 circuits.


50000001 512008-05-09

Figure 23 T1 Interface Configuration page

E1 Interface Configuration Page

This page allows the administrator to enable/disable each individual E1 channel. The AIS can also be enabled and disabled for each input. If enabled, the radio places an AIS code on the output of the associated interface if and when the link fails or when there is no E1 signal available from the far end to provide the user at the local end. Loopback controls are also provided (see T1/E1 Loopback).

Figure 24 E1 Interface Configuration page


52 500000012008-05-09

T1/E1 Loopback

Loopback is provided for any enabled T1 or E1 port. As shown in and , the choices are:

• No Loopback (default)

• External (local)

• External (remote)

• Internal

All loopback configurations control the loop at the Line Interface integrated circuit, which is the device wired directly to the front panel ports.

External loopback modes are used in conjunction with an external test source. The designation of ‘local’ or ‘remote’ refers to where the loopback is occurring relative to the location where the loopback is implemented. That is, on the radio being accessed, if External (remote) is selected, this loops the signal back at the remote radio interface back towards the local radio. Likewise, if External (local) is selected, the signal loops back at the local interface towards the remote radio (Figure 25 and Figure 26).

Figure 25 External (remote) loopback

Figure 26 External (local) loopback

When a local T1/E1 port is configured for External (remote) loopback, it is the same as configuring the remote radio for External (local) loopback.

Internal loopback uses an internal test source, and sends the test source signal across the link, looped at the remote radio’s interface, returned to the local radio, and looped at the local radio’s interface back to the source. The inputs at both ends are looped back at the line level. illustrates the internal loopback function.

Figure 27 Internal loopback

Note: Only one Internal loopback can be enabled at any time.


50000001 532008-05-09

File Transfer PageThis page allows the administrator to upload and download files to and from the radio. Three types of files can be uploaded: configuration, radio firmware, and Regulatory Domain Database (RDD). When uploading Configuration Files, current configuration parameters are immediately overwritten, and the unit automatically reboots. When uploading radio firmware files, the file is placed into reserve memory space. After the new radio firmware file uploads, use the File Activation page to enable the files (see File Activation Page).

Figure 28 File Transfer page

Up to four types of files can be downloaded: configuration, radio firmware, radio event log, and MIB. The MIB file refers to the Management Information Base related to the Simple Network Management Protocol (SNMP) function, and is only available on models which support SNMP. See Simple Network Management Protocol (SNMP) for more information.

Note: Issues with the RDK may be caused when the Regulatory Domain Database (RDD) is not up to date. Go to the Exalt Web site to download the current RDD.

http://www.exaltcom.com/support/downloads.htm


54 500000012008-05-09

Use the following steps to download a file.

1 Select the type of file to download (configuration or radio firmware).

2 Click the Download button and wait for the radio to prepare the file for download.

For the MIB file download, a second page/link appears (Figure 29).

3 Left-click the link on the page to download the file to a desired location.

Figure 29 File Transfer page—download file link

File download and upload is useful when configuring several radios with similar settings. A copy of the configuration file can also help restore radio settings. In addition, a copy of the Exalt default configuration file is helpful to restore the radio to factory settings.

If copying the same configuration file into multiple radios, some parameters will match and that may be undesirable. However, it may be easier to change just a subset of parameters rather than every parameter. The following parameters can cause problems or confusion if they match at each of a link:

• Radio Name

• Endpoint Identifier

Note: Check the before uploading radio firmware files. New file uploads overwrite the secondary file location. If important files reside in the primary or secondary file location, download them before uploading the new files. Only the active radio firmware file can be downloaded. Therefore, to download the reserve file, it must first be activated (using the Swap button). See File Activation Page. The current radio firmware and RDD versions can be viewed on the Radio Information Page.

Note: Do not change the name of any download file. The configuration file must be named config.nv. To keep track of multiple configuration files, use a folder naming system or temporarily rename the file, however, it must be named config.nv before it can be uploaded to a radio. Never change radio firmware file names under any circumstances.


50000001 552008-05-09

• IP Address

• IP Subnet Mask

• Default Gateway

The following parameters can match at both ends of the link:

• Link Name

• Link Security Key (although each link should be different)

• Admin and User passwords

• Bandwidth

• RF Frequency

• Link Distance

• TDD Frame Size

• T1/E1 configurations

• Ethernet configurations


56 500000012008-05-09

File Activation PageUse this page to move stored or uploaded files for use on the radio. The page indicates which file is currently in use, and which file is available for use. Click the Swap button to place the file in the Alternative File column into the active state and move the file in the Current File column to the Alternative File column.

Figure 30 File Activation page

Note: In all cases, the radio reboots after a new file is selected using the Swap function. This places the radio out of service for a short time.


50000001 572008-05-09

GPS Information PageThis page provides information on how many GPS satellites are within the view of the Exalt GPS receiver. This page is active for implementations that include the GPS receiver connection for synchronization. This information can be helpful for troubleshooting GPS issues.

Figure 31 GPS Information page


58 500000012008-05-09

Alarms PageThis page provides an easy-to-read summary of the alarm status of both local and remote radios. The colors on this page reflect the color of the alarms displayed on the radio front panel. However, additional detail displays on this page to aid in quick assessment of issues and status.

Figure 32 Alarms page

Table 6 lists alarm status conditions that appear on this page.


50000001 592008-05-09

The Temperature alarm monitors the internal temperature of the unit based on specific points inside the radio chassis. It is normal for the internal temperature to be above the ambient temperature, so the temperature reading may be higher than the highest specified ambient temperature. When the internal electronics reach a point that is higher than the normal temperature rise at the highest ambient temperature, the temperature alarm turns yellow. Power down the radio as soon as possible, and investigate the cause of the temperature rise before the radio is put back into service. In almost all cases, a temperature alarm is due to an external cause.

Table 6 Alarm status indicatorsLabel Status

Link Indicates RF link status:

• Green Solid = Error-free connection (BER<10e-6)

• Yellow Solid = Errored connection (10e-3>BER >10e-6)

• Red Solid = No link (BER>10e-3)

DFS Indicates the status of the Dynamic Frequency Selection (DFS).

• Green = No DFS activity, normal transmission

• Red = Either CAC or NOP is in progress.

Collocation Indicates the enabled/disabled status with Internal or GPS sync and current alarm status.

• Green Solid = Sync enabled and sync input present

• Yellow Solid = Sync enabled and missing proper sync input in flywheel operation period

• Red Solid = Sync enabled and missing proper sync input signal and flywheel period expired

Ethernet Main • Green Solid = Data present

• Off = No data present

T1/E1 Input • Green = Enabled and connection present (clocking confirmed)

• Red = Enabled and no connection present

• Grey = Disabled or unavailable due to configuration

Temperature • Green Solid = Normal temperature range

• Yellow Solid = Exceeding normal temperature range


60 500000012008-05-09

Performance PageThis page provides statistical information about the performance of the system in relation to the integrity of the user data and the RF link.

Figure 33 Performance page

• The Current BER field indicates the current bit error rate of the link. If the link is operating perfectly, this should indicate zero. Generally, the link should remain at a BER less than 1x10-6 (1 bit out of every million bits errored). This is the threshold performance specification and the standard to which the link was engineered. However, radio links can and are affected by weather, interference, and other external sources and will occasionally have a higher error rate. A link remains operational unless the BER exceeds 1x10-3 (1 bit out of every hundred bits errored). Consult the link design engineer for an understanding of the predicted error rate of the radio link as it has been designed. Many applications are unaffected by bit errors, but TDM circuits (for example, T1 or E1) are more sensitive. Also, if the link operator is providing a service guarantee, this value may need to be monitored or examined in cases of service issues. The behavior of BER in relation to other alarms or measurements and external events can be very helpful in troubleshooting activities.

• Current RSL is the measurement of the received signal level at the radio antenna port. This is the measured level of the RF signal coming from the opposite end of the radio link. The link was engineered to a specific RSL by the link design engineer, and this RSL should be obtained during installation and remain relatively stable during the operation of the link. RSL can and will vary as a result of weather changes and other external sources, such as path obstructions. Once again, this variation was part of the original design to achieve a certain level of performance over time. Bit errors occur when the RSL falls to a level within roughly 3dB of the threshold specification. When the RSL falls below the threshold specification, the link disconnects and will not reconnect until the RSL is above the threshold specification. The behavior of RSL in relation to other alarms or measurements and external events can be very helpful in troubleshooting activities.


50000001 612008-05-09

• Errored Seconds (ES) indicates the total number of seconds that occurred where there was at least one bit error since the last time that the radio statistics counter was reset. Generally, ES are not a significant concern, so long as they are not continuous or above the anticipated performance based on the original link engineering goals. If ES are continuous or at a high rate, this is normally an indication of poor link performance due to poor RSL or interference, or severe impact by weather or other environmental factors. However, similar to the performance factors previously listed, ES can and will occur in any radio link. Once again, consult the link engineer to determine the original design goals, and compare actual performance to these expectations to determine if any improvements are necessary or if other problems may be causing excessive ES.

• Unavailable Seconds (also called UAS) are similar to ES, but this counter keeps track of every second where the bit error rate equals or exceeds 1x10-3, as well as any seconds where there is a complete loss of radio communication, over the period since the last counter reset. If Unavailable Seconds are continuous or at a high rate, this is normally an indication of poor link performance due to poor RSL or interference, or severe impact by weather or other environmental factors. However, similar to the performance factors listed above, Unavailable Seconds can and do occur in any radio link. Consult the link engineer to determine the original design goals, and compare actual performance to these expectations to determine if any improvements are necessary or if other problems may be causing excessive Unavailable Seconds.

• Minimum RSL indicates the worst (lowest) received signal level that occurred since the last counter reset. It is helpful to know if the RSL dropped significantly from the normal level, or has reached a level near or below threshold.

• Minimum RSL Timestamp indicates the date and time when the Minimum RSL occurred. This is helpful for general troubleshooting, and especially comparing to items in the event log or diagnostic charts from the same time period.

• Maximum RSL indicates the best (highest) RSL that occurred since the last counter reset. This indicates the best performance of the radio link, which is normally equal to the installed value, and is usually the designed value.

• Time Since Reset indicates the amount of time passed since the last counter reset. This helps to quantify the seriousness of other statistics, such as ES and Unavailable Seconds, if there have been high numbers of ES and/or Unavailable Seconds over a relatively short period of time.

Each end of the link statistics on this page can be independently reset using the Reset Statistics button for the local or remote radio. It is good practice to reset the statistics at the time that the link is commissioned (after all antenna alignment is complete and stable RSL at designed levels is achieved, and no more system reboots are anticipated). Make a habit of viewing this page regularly, make records of the performance, and reset the statistics so that the counters can more precisely pinpoint issues.

Note: Unavailable Seconds do not register as ES. In other words, the ES counter counts all seconds that are errored NOT INCLUDING the seconds that were classified as unavailable. The total number of seconds with errors or outages is the sum of ES and Unavailable Seconds.

Note: Resetting statistics from one end also resets the statistics for the same radio at the opposite end. That is, if the Local statistics are reset, logging into the remote end shows the Remote statistics on that end (which is the local radio in the first condition) as being reset at the same time.


62 500000012008-05-09

Event Log PageUse this page to review a list of the events logged by the radio. The following items are listed in the event log:

• Alarms

• Alarms clearing (Normal)

• Radio Reboots

Every event is tagged with the time that the event occurred, and a severity and type. The event log also allows filtering to limit the view of the log to the lowest level of desired information. For example, a filter level of Minor displays Minor, Major, and Critical severity events.

The log contains the last 1000 events. Events are deleted on a FIFO basis, erasing the oldest entries to make room for the newest entries.

The event log can be cleared and be downloaded from the radio (some models may require a software upgrade to enable this feature). A screen capture of the browser window can serve as a useful record.

Figure 34 Event Log page


50000001 632008-05-09

Diagnostic Charts PageUse this page as an aid in troubleshooting. This page illustrates the historical (and current) performance for three parameters: RSL, Radio Temperature, and BER.

The horizontal scale illustrates 120 points of time measurement and is synchronized on all three graphs. The scale displays in minutes, hours, or days from the last two hours (120 minutes), five days (120 hours), or four months (120 days). All information is stored, so all of these periods are available for short- and long-term performance analysis. The right side of a graph represents the most recent measurement, and data ‘marches’ from the right-to-left at every interval.

The vertical scale of each chart independently scales to show the maximum resolution based on the maximum variation of the data over the selected time measurement.

Figure 35 Diagnostic Charts page

Use the cursor to point to any spot on any of the three charts, and all three charts illustrate the measurements taken for that time interval in the upper-left corner of each chart. The time interval is indicated by T=(value). This is followed by the value of the measurement, listing the highest value, lowest value and average value measured over that time interval.

For example, in Figure 35 the displayed time interval is minutes, and the cursor is held at the T=17 mark on the horizontal axis. The measurements shown indicate performance from 17 minutes ago. The high/low/average values shown on each chart are measurements made across that specific one-hour interval.

Changes in RSL often have an impact on BER, and this can be confirmed by looking for synchronized events. When BER events occur without corresponding changes in RSL, this normally indicates


64 500000012008-05-09

interference, atmospheric changes, transmission system issues (such as problems with cables, connectors or antennas), or possibly radio hardware problems.

It is also useful to help determine if changes in radio temperature are occurring, and if they are having any impact on RSL or BER. If the radio is mounted in an environmentally controlled location, this has less relevance. However, temperature monitoring can be helpful to ensure that the radio is operating within specifications.


50000001 652008-05-09

Spectrum Analyzer PageThe spectrum analyzer feature provides a useful pre-planning and troubleshooting tool. This feature is only available on radios with firmware supporting the spectrum analyzer. Perform a spectrum analysis after deployment and just before commissioning to maintain a record of the spectrum at the time of deployment. Figure 36 shows the Spectrum Analyzer page.

Figure 36 Spectrum Analyzer page

While a professional spectrum analyzer provides higher levels of control and precision for pre-planning, the Spectrum Analyzer page allows evaluation of the RF spectrum as seen at the radio’s RF input port prior to deployment. This is useful for pre-planning the center frequency and occupied bandwidth, and to determine polarization and antenna type and mounting locations.

For troubleshooting, enable the spectrum analyzer to scan the desired segment or full band of the frequency range. Select the step size and set the remote radio transmitter ON or OFF. This allows viewing of the clean spectrum without the remote transmitter on and a comparison of the remote transmitter in the midst of other signals.


66 500000012008-05-09

Use the smallest step size to obtain the finest view of the spectrum. The spectrum analyzer can be set to match the start and stop frequency for a dwell mode. Peak and average detection modes are also available. Peak detection is helpful for capturing intermittent events such as pulsed emissions.

It is best to set the Scan Time option to a time value as opposed to using the ‘infinity’ setting. If your management computer is connected to the radio through the radio link, access to the GUI is interrupted during the duration of the analysis.

The spectrum analyzer graph displays received signals in red or green (Figure 37), normalized in dBm to the resolution bandwidth of the analyzer. Red indicates a peak hold function. This is the highest level detected during the entire scan. Green indicates the last value measured at that frequency.

Figure 37 Spectrum analyzer graph example

A completely green vertical box indicates that the signal maintained a steady level for the entire scan or that the last scan measured at a strong or stronger level than the rest of the analysis. A completely red vertical box indicates that there was a signal at some point during the scan, but that the signal was not detected at the last scan. A graph displaying green on the lower part and red at the upper part indicates that at some time during the scan, a signal was detected at a higher level than was detected during the last scan.

The last spectrum analyzer scan performed displays in this page until the radio is rebooted. You can do a screen capture for record keeping and for comparison to future analyses. The time and date of the analysis displays on the page, which is handy as a reference in a screen capture.

Note: Enabling the spectrum analyzer interrupts all radio traffic for the duration of the analysis. In addition, access to the radio’s GUI may also be interrupted, depending on the location of the interfaced computer relative to the radio where the spectrum analysis is occurring. The GUI is available at the completion of the spectrum analysis.

Note: The result of selecting infinity may be complete loss of contact to that radio and may require a physical visit to the radio location to disable the spectrum analyzer.


50000001 672008-05-09

Reboot PageUse this page to reboot the radio. The function may never be required, but can be used in emergencies. All configurations that require a reboot automatically reboot on administrator confirmation.

Figure 38 Reboot page


68 500000012008-05-09

Manual PageThe manual (this document or the version that matches the installed firmware) is available within the GUI. Adobe Acrobat Reader 5.5 or higher is required (go to www.adobe.com to download Acrobat Reader). Click the Manual link to display the manual within the browser window. Once the manual displays, click the save button on the PDF toolbar to download the manual locally.

Figure 39 Manual page

http://www.adobe.com


50000001 692008-05-09

SpecificationsThis section presents specifications for the r-Series of Digital Microwave Radios.

Physical Specifications

Integrated Antenna Models

EX-4.9r-c, EX-5r-c, and EX 5r-c IP

Legacy Models

Physical Configuration Outdoor unit (ODU)Dimensions (H x W x D) 14.6 x 14.6x 3.8"/37 x 37 x 9.7 cmWeight 12 lbs; 5.5 kgOperating Temperature –40 to +149°F /–40 to +65°C; Altitude 15,000'/4.6 km Humidity 100% condensingEnvironmental NEMA4/IP56

Physical Configuration Outdoor unit (ODU)Dimensions (H x W x D) 14.6 x 14.6x 2.5"/37 x 37 x 6.4 cmWeight 12 lbs; 5.5 kgOperating Temperature –40 to +149°F /–40 to +65°C; Altitude 15,000'/4.6 km Humidity 100% condensingEnvironmental NEMA4/IP56

Physical Configuration Outdoor unit (ODU)Dimensions (H x W x D) 13 x 13 x 4.25"/33 x 33 x 10.8 cmWeight 15 lbs; 6.8 kgOperating Temperature –40 to +149°F /–40 to +65°C; Altitude 15,000'/4.6 km Humidity 100% condensingEnvironmental NEMA4/IP56


70 500000012008-05-09

Common System Specifications

Tuning Resolution 1MHz; 5MHz for EX-4.9r and some regulatory domainsPower Control Step Size 0.5dBSelectable Modulation Modes Mode 1 (QPSK); Mode 2 (16QAM)Selectable Frame Lengths (ms) 0.5, 1, 2, 2.5, 4, 5Maximum Aggregate User Capacity a

a. Not all bandwidth and mode combinations are available on all radio models. Some radios may requirespecific software license keys, which can be purchased from your authorized Exalt representative.

Error Floor 10-12

Frequency Stability +7 ppmLink Security 96-bit Security Code

Mbps Mode Mode

8/10MHz 13 27

16/20MHza 27 54

32MHz 55 110

64MHza 110 216


50000001 712008-05-09

EX-4.9r System SpecificationsFrequency Band 4940 to 4990MHzTunable Range 4945 to 4985MHzOutput Power (at full power)

Selectable Channel Bandwidths 10MHz, 20MHza

a. Mode 2 for 20MHz BW is enabled through firmware options for the EX-4.9r.

Receiver Threshold (BER=10-6)

Maximum RSL Mode 1: -25dBm error-free; 0dBm no damageNon-overlapping channels 10MHz: 5; 20MHz: 2Regulatory Compliance FCC Part 90; IC RSS-111FCC ID TTM-104P90RIC ID 6254A-104P90REmission Designator(s)

dBm Mode 1 Mode 2

10MHz +22 +21

20MHz +24 +21

dBm Mode 1 Mode 2

10MHz -86 -78

20MHz -83 -75*

10MHz 8M72W 10MHz

20MHz 19M0W 20MHz


72 500000012008-05-09

System Specifications, 5.3GHz BandFrequency Band 5250 to 5350MHzTunable Range 5260 to 5332MHzOutput Power (at full power) +13dBm (0.02W)Output Power (at minimum power) -7dBmSelectable Channel Bandwidths 8MHz, 16MHz, 32MHz, 64MHza

a. A firmware option is required to enable 64MHz BW in jurisdictions where it is permitted. For someregulatory domains, the 8MHz Bandwidth setting displays as 10MHz, and the 16MHz Bandwidthsetting displays as 20MHz.


Maximum RSL Mode 1: -25dBm error-free; 0dBm no damageNon-overlapping channels 8MHz: 10; 16MHz: 5; 32MHz: 2; 64MHza: 1Regulatory Compliance FCC 15.407; IC RSS-210FCC ID TTM-105P25MIC ID 6254A-105P25REmission Designator(s)

dBm Mode 1 Mode 2

8MHz -86 -78

16MHz -83 -75

32MHz -80 -72

64MHz* -77 -69

8MHz 7M8W7D

16MHz 15M7W7D

32MHz 30M9W7D

64MHz* 60M8W7D


50000001 732008-05-09

System Specifications, 5.4GHz BandFrequency Band 5470 to 5725 MHzTunable Range 5488 to 5715 MHzOutput Power (at full power) +13dBm (0.02W)Output Power (at minimum power) -7dBmSelectable Channel Bandwidths 8MHz, 16MHz, 32MHz, 64MHza

a. A firmware option is required to enable 64MHz BW in jurisdictions where it is permitted. For someregulatory domains, the 8MHz Bandwidth setting displays as 10MHz, and the 16MHz Bandwidth set-ting displays as 20MHz.


Maximum RSL Mode 1: -25dBm error-free; 0dBm no damageNon-overlapping channels 8MHz: 29; 16MHz: 14; 32MHz: 7; 64MHza: 3Regulatory Compliance FCC 15.407; IC RSS-210; ACMAFCC ID TTM-105P25MIC ID 6254A-105P25REmission Designator(s)

dBm Mode 1 Mode 2

8MHz -86 -78

16MHz -83 -75

32MHz -80 -72

64MHz* -77 -69

8MHz 8M3W7D

16MHz 16M7W7D

32MHz 33M0W7D

64MHz* 65M0W7D


74 500000012008-05-09

System Specifications, 5.8GHz BandFrequency Band 5725 to 5850 MHzTunable Range 5731 to 5844 MHzOutput Power (at full power) +24dBm (0.25W), Mode 1

+21dBm (0.13W), Mode 2Output Power (at minimum power) +4dBmSelectable Channel Bandwidths 8MHz, 16MHz, 32MHz, 64MHza

a. A firmware option is required to enable 64MHz BW in jurisdictions where it is permitted. For someregulatory domains, the 8MHz Bandwidth setting displays as 10MHz, and the 16MHz Bandwidth set-ting displays as 20MHz.


Maximum RSL Mode 1: -25dBm error-free; 0dBm no damageNon-overlapping channels 8MHz: 15; 16MHz: 7; 32MHz: 3; 64MHza: 1Regulatory Compliance FCC 15.247; IC RSS-210; ACMAFCC ID TTM-105P25MIC ID 6254A-105P25REmission Designator(s)

(dBm) Mode 1 Mode 2

8MHz -86 -78

16MHz -83 -75

32MHz -80 -72

64MHz* -77 -69

8MHz 8M4W7D

16MHz 16M7W7D

32MHz 33M1W7D

64MHz* 64M5W7D


50000001 752008-05-09

Interfaces RF (x2, EX-4.9r-c, EX-5r-c, and EX-5r-c IP)

TDM (x2, 2 interfaces each; not activated on the IP versions)

Ethernet

Sync-In

Power — Power Injector

Integrated Antenna

Integrated Antenna—Legacy Models (EX-4.9r, EX-5r, and EX-5r IP)

Connector N-type femaleImpedance 50 Ohms

Connector RJ-45 (RJ48C), femaleT1 Impedance 100 Ohms, balancedT1 Line Codes AMI, B8ZS, selectableT1 LBO Settings (in ft.) 0-133, 133-266, 266-399, 399-533, 533-655T1 Clocking Speed 1.544 MbpsT1 Compliance ANSI T1.102-1987; ITU-T; G.823; GR-49T-COREE1 Impedance 120 Ohms, balancedE1 Line Codes HDB3E1 Clocking Speed 2.048 MbpsE1 Compliance CEPT-1; G.703; ITU-T-G703

Connectors RJ-45, female, auto-MDIXInterface Speed 10 or 100 MbpsDuplex Half, full, auto, selectableCompliance 802.3

Connector RJ-45, femaleSignal 1pps (GPS)

Connector 6-pin barrier stripInput Voltage 48VDCConsumption <60 W (1.25A)

Gain, EX-5r, EX-5r IP (midband) 24dBiGain, EX-4.9r (midband) 23dBi3dB Beamwidth 9 degreesPolarization Switch-selectable vertical or horizontal

Gain (midband) 20dBi3dB Beamwidth 15 degreesPolarization Switch-selectable vertical or horizontal


76 500000012008-05-09

Interface ConnectionsThis section provides the pin number assignment and wiring information for the connectors on the r-Series radios. All connectors are shown as viewed from the radio front panel, as shown in Figure 40.

Figure 40 r-Series connector orientation

TDM ConnectionsThere are two connectors for TDM; each connector has two TDM circuits available. Figure 41 illustrates the pin orientation and functionality of these connectors. These connectors are disabled on the IP version radios.

Figure 41 TDM connectors

RSL & GPS Sync ConnectorThis connector can be used during the antenna alignment process, to provide a received signal level (RSL) voltage to a voltmeter. The connector is also used for connection to an optional Exalt GPS antenna for the purposes of GPS synchronization. Figure 42 illustrates the pin orientation and functionality for this connector.

Pin Function

1 Tip Out (from radio) – Ch.1 & 2

2 Ring Out (from radio) – Ch.1 & 2

3 Tip Out (from radio) – Ch.3 & 4

4 Tip In (to radio) – Ch.1 & 2

5 Ring In (to radio) – Ch.1 & 2

6 Ring Out (from radio) – Ch.3 & 4

7 Tip In (to radio) – Ch.3 & 4

8 Ring In (to radio) – Ch.3 & 4


50000001 772008-05-09

Figure 42 RSL & GPS connector

Power/Ethernet ConnectorThis connector is the primary connector on the radio, and must be connected to provide power to the radio, and primary Ethernet communications for traffic and Ethernet. Figure 43 illustrates the pin orientation and functionality for this connector.

The Ethernet connector implements Auto-MDIX, and therefore either ‘straight’ or ‘crossover’ Ethernet cables may be used, independent of the wiring of the connected device. The wiring follows typical wiring for Power-over-Ethernet (PoE), however the power consumption requirement for the r-Series radio does not allow for ‘standard’ (802.3af) PoE, and only the Exalt power injector shall be used. In addition, the Exalt power injector provides critical reset and alarm capability that would not be available from a generic PoE injector, even if the power consumption requirement is met.

Figure 43 Power/Ethernet connector

Pin Function

1 +5V out to GPS antenna

2 Ground

3 Tx Data to GPS antenna

4 Enable signal to GPS antenna

5 Rx Data from GPS antenna

6 1pps signal from GPS antenna

7 Received Signal Level (RSL)

8 Unused

Pin Function

1 Paired with Pin 2

2 Paired with Pin 1

3 Paired with Pin 6

4 +DC Power (48V) In

5 +DC Power (48V) In

6 Paired with Pin 3

7 -DC Power (48V) In

8 -DC Power (48V) In


78 500000012008-05-09

AntennasTable 7 lists antennas supported by the EX-5r models for use in the USA. In some countries, antennas exceeding a certain level of gain may be unlawful. Refer to RF Output Power Setting for details on regulatory limits.

Table 7 Supported antennas

Manufacturer Model # Description Midband Gain (dBi)3dB (Azimuth/Elevation)Beamwidth (degrees)

Andrew P2F-52-N 2-foot Dish 29.4 5.4Andrew PX2F-52-N 2-foot Xpol Dish 29.4 5.4Andrew P3F-52-N 3-foot Dish 33.4 3.8Andrew PX3F-52-N 3-foot Xpol Dish 33.4 3.8Andrew P4F-52-N 4-foot Dish 34.9 3.0Andrew PX4F-52-N 4-foot Xpol Dish 34.9 3.0Andrew HP2F-52- 2-foot HP Dish 29.0 5.4Andrew HPX2F-52- 2-foot Xpol HP 29.0 5.4Andrew HP3F-52- 3-foot HP Dish 33.0 3.8Andrew HPX3F-52- 3-foot Xpol HP 33.0 3.8Andrew HP4F-52- 4-foot HP Dish 34.5 3.0Andrew HPX4F-52- 4-foot Xpol HP 34.5 3.0Andrew HP6F-52- 6-foot HP Dish 37.2 1.8Andrew HPX6F-52- 6-foot Xpol HP 37.2 1.8Andrew FPA5250D06 6-inch Panel 18.0 19.3Andrew FPA5250D12 1-foot Panel 23.6 9.6Exalt (Integral) 1-foot Xpol Panel 20.0 15.0Gabriel DFPS.5-52 6-inch Panel 18.0 19.0Gabriel DFPD1-52 1-foot Panel 23.5 9.4Gabriel DFPD2-52 2-foot Panel 28.0 4.6Gabriel QF2-52-N 2-foot Dish 28.5 5.6Gabriel QF2.5-52-N 2.5-foot Dish 31.2 4.4Gabriel QF4-52-N 4-foot Dish 34.8 2.7Gabriel QFD2-52 2-foot Xpol Dish 28.4 5.6Gabriel QFD2.5-52 2.5-foot Xpol Dish 31.1 4.4Gabriel QFD4-52 4-foot Xpol Dish 34.7 2.7Gabriel HQF2-52-N 2-foot HP Dish 28.2 5.7Gabriel HQF4-52-N 4-foot HP Dish 34.4 2.8Gabriel HQF6-52-N 6-foot HP Dish 37.4 1.9Gabriel HQFD2-52 2-foot Xpol HP 28.1 5.7Gabriel HQFD2.5-52 2.5-foot Xpol HP 30.7 4.5Gabriel HQFD4-52 4-foot Xpol HP 34.3 2.8Gabriel HQFD6-52 6-foot Xpol HP 37.3 1.9MTI MT-485001 7.5-inch Panel 19.0 18.0MTI MT-485002 1-foot Panel 23.0 9.0MTI MT-486004 18-inch Panel 26.0 6.0


50000001 792008-05-09

MTI MT-486001 2-foot Panel 28.0 4.5MTI MT-485005 7.5-inch Xpol 18.0 17.0MTI MT-485025 15-inch Xpol Panel 23.0 9.0Radio Waves FP.5-5-18 6-inch Panel 18.0 20.0Radio Waves FP1-5-24 1-foot Panel 23.8 10.0Radio Waves FP2-5-28 2-foot Panel 28.0 4.5Radio Waves FPD.5-5-18 6-inch Xpol Panel 18.0 20.0Radio Waves SP1-5.2 1-foot Dish 22.5 11.1Radio Waves SP2-5.2 2-foot Dish 29.0 6.1Radio Waves HP2-5.2 2-foot HP Dish 28.6 6.1Radio Waves SP3-5.2 3-foot Dish 32.0 4.0Radio Waves SP4-5.2 4-foot Dish 34.8 3.0Radio Waves SPD2-5.2 2-foot Xpol Dish 28.1 6.2Radio Waves SPD3-5.2 3-foot Xpol Dish 31.1 4.2Radio Waves SPD4-5.2 4-foot Xpol Dish 34.4 3.1Radio Waves SPD6-5.2 6-foot Xpol Dish 37.5 2.1RFS SPF2-52A 2-foot Dish 27.9 6.2RFS SPF3-52A 3-foot Dish 31.4 4.2RFS SPF4-52A 4-foot Dish 33.9 3.1RFS SPF6-52A 6-foot Dish 37.4 2.1RFS SDF4-52A 4-foot HP Dish 33.9 3.1RFS SDF6-52A 6-foot HP Dish 37.4 2.1RFS MA0528- 7.5-inch Panel 19.0 18.0RFS MA0528- 1-foot Panel 23.0 9.0RFS MA0528- 2-foot Panel 28.0 4.5

Table 7 Supported antennas (Continued)

Manufacturer Model # Description Midband Gain (dBi)3dB (Azimuth/Elevation)Beamwidth (degrees)

rhogan

Highlight


80 500000012008-05-09

TroubleshootingThis section provides information regarding troubleshooting of common issues and alarms on these radios. Exalt Digital Microwave Radio systems are designed by Exalt’s expert engineers with extensive experience through multiple generations of microwave radio design. These new-generation systems contain extensive diagnostic tools, alarm indications, and troubleshooting aids. And, as compared to other systems in their class, are easier to install, maintain, and troubleshoot. The GUI provides information to aid in troubleshooting (see Diagnostic Charts Page).

Contact Exalt Customer Care for further assistance with issues with your Exalt radio and with suggestions on how the radio and documentation can be improved.

General PracticesTroubleshooting a microwave radio link can be a complex task. Approach troubleshooting as a process of elimination, and first determine which portions of the system are operating properly.

In a vast majority of cases, failures or poor performance of microwave links is attributed to something other than the microwave radio hardware. In this respect, the back-to-back bench test (see Back-to-back Bench Testing) is very important to determine if radio hardware is operating properly and eliminate many variables in the troubleshooting process.

If a back-to-back bench test fails, then the radio hardware is either broken or the radios are improperly configured. Upgrade the radio to the most current release of firmware, and/or reset the radio to its critical factory settings, following the quick start guide instructions and those in Configuration and Management, helps to confirm if configuration issues cause failure. The most common issues with microwave radio links are:

• An improperly terminated RF cable

• Multipath propagation

• RF interference

• Path obstruction

• Misaligned antenna

• Faulty antenna

• Improper grounding

• Insufficient link margin in the design/implementation

• Moisture in the transmission system (antenna feed and/or RF cable)

If the radio link has been operating without issues and is exhibiting new poor performance behavior or becomes completely inoperative, the troubleshooting process should pay close attention to any conditions that may have changed between the time when the system was working without issue and the time when the issues started.

Also, it can be helpful to compare some performance parameters of the system before and after the presence of issues. Often the source of the issues can be determined by thoughtful consideration of changes, such as:

• Changes in weather, including high winds

• Changes made to the radio equipment, transmission system, or connected equipment

• New radio systems or electronic equipment the nearby radio or transmission system


50000001 812008-05-09

• New construction nearby either end of the link, or along the path

• Tree growth, flooded fields, or changes in rivers/lakes along the path

Verify that configurations are set as follows:

• RF matches at each end of the link

• Bandwidth matches at each end of the link

• Link distance matches at each end of the link

• TDD Frame Length matches at each end of the link

• Endpoint Identifier is different at each end of the link (one end Radio A, one end Radio B)

• Ethernet interfaces are enabled, as desired

• AUX Ethernet is set for in-band or out-of-band NMS, as desired

• T1/E1 enabling matches at each end of the link

• Link security key matches at each end of the link

Also, use the ExaltCalc tool in the design phase to determine the optimum setting for the Bandwidth and TDD Frame Length parameters for the given link distance, and provides guidance to the expected RF link performance, as well as throughput, latency, and number of supported T1/E1 circuits.

Typical Indications of IssuesIn many cases, microwave radio users do not notice changes or degradation to the radio system until the radio system fails completely or becomes highly errored or significantly intermittent. However, regular management of the radio system can help indicate changes in performance that have not yet impacted user performance, but may impact performance at a later date if left unchecked or unaddressed. The administrator can use this as an opportunity to be proactive and monitor the radio link performance regularly, watching for unexplained or unexpected changes in performance and trends in performance changes.

Most importantly, monitoring radio system RSL over time indicates the performance of the radio system. Address any long-term drop in RSL and erratic or unsteady RSL. Some RSL changes are expected and weather patterns and the related multipath can cause dramatic RSL changes resulting in system outage. However, that outage should not occur at a significantly greater rate than the designed long-term performance. Consult the path design engineer for more information about link reliability expectations and anticipated RSL deviation.

In addition, regular inspection of the transmission system (RF cables and antennas) and paying close attention to changes along the path, such as construction or tree height, or new microwave radio installations nearby, can be extremely helpful and proactive.

When link performance is very poor, alarms on the radio front panel and within the radio’s management system indicates particular failures. Consult this manual for more information on the specific alarms and diagnostics, or contact Exalt Customer Care for assistance.

Exalt Customer Care is primarily motivated to determine if the radio hardware is faulty and require return for repair, and to help execute an effective and efficient repair and return process for radio terminals believed to be faulty. However, Exalt Customer Care provides advice regarding the total radio system and RF path engineering and environment, and advises on troubleshooting.

End users should first contact the installer and/or designer of the system. In many cases, an in-depth understanding of RF design is required, and on-site analysis and special test equipment, may be


82 500000012008-05-09

necessary. Compared to phone support from Exalt Customer Care, troubleshooting is much more expeditious if the professional installer and/or link designer examines the system and reviews the management information in the GUI. In turn, if the professional installer and/or link designer contacts Exalt Customer Care, the process to rectify the system is much more expedient due to the in-depth knowledge related to the implementation and the RF environment.

Improper RF Cable TerminationImproper RF cable termination is a very common problem. In many cases, this is a problem that occurs during installation and is not a problem that suddenly appears. However, if cables are moved or flexed, especially near the termination points, and radio errors, changes in RSL, or other performance issues occur, this is a certain sign of this issue.

Another relatively easy method to test for this condition is to decrease the output power of the radio system (at each end, one end at a time). A poor RF cable termination may be reflecting too much RF energy back into the radio system, and reducing output power reduces the reflected energy at a faster rate than the transmitted energy towards the far end. Be careful not to reduce the output power to the point where the radio’s threshold is reached. Typically, a reduction of just 3 to 6dB is enough to determine if this is the issue. If the reduction of output power clears the error condition, this is the likely cause.

Use a reflectometer or meter that can read VSWR at the operating frequency to identify poor terminations as well as poor antenna feeds.

Multipath PropagationMultipath propagation is a term that encompasses changes to the RF path, such as reflections and/or refraction, causing partial or complete destruction of the radio signal, and thus excessive bit errors and/or system outages.

Rapid changes in temperature, inversion layers, humidity, air pressure, water evaporation, as well as standing water or moisture on objects along the path are all examples of changes that can cause multipath propagation. New building construction near either end of the path or along the path can cause new reflection characteristics.

If your system has been operating without issue and is suddenly experiencing issues that are symptomatic of a certain time of day or related to change in climatic events or some of the external factors listed above, this is likely the cause. Consult a professional RF path engineer in these cases. Often, minor repositioning of the antennas at either or both ends can reduce or eliminate these problems.

RF InterferenceRF interference is usually indicative of another radio system nearby either end of your radio system or aimed towards one or both ends of your radio system – usually at or near the same frequency and usually with a similar signal level.

Other forms of RF interference also exist, such as electronic equipment placed close to the radio chassis or transmitters that couple onto the cabling or grounding system of the radio. Microwave ovens and wireless communication devices used near the equipment or cabling are examples of electronic equipment interference.

Note: The Praxsym VSWR meter is an excellent tool for this purpose.


50000001 832008-05-09

RF interference, like most other causes of problems, is indicated by significant bit errors and/or system outages.

One means to determine presence of interference is the use of a spectrum analyzer that covers the same range as the radio system. A professional RF engineer can use a spectrum analyzer to locate sources of interference, measure these sources, and determine potential remedies to take to operate in the presence of interference.

If a spectrum analyzer is not available, the radio’s RSL port can help determine RSL levels of interfering signals. By turning the far-end radio off, the residual RSL measured by the radio indicates the level of interference seen by the radio. It is possible that interference levels below that which can be measured still have an impact on the radio system – especially if the radio system has low fade margin or is using a high order modulation.

Exalt Digital Microwave Radios provides considerable flexibility to tune to different frequencies across the bands within which they operate. This is the easiest method to use to try to avoid existing interference. In addition, the occupied bandwidth of the radio can be reduced. This, along with re-tuning, can be very effective, however throughput is reduced.

Repositioning the antenna and/or changing polarization, or upgrading the antenna to a higher gain, and/or using a high-performance antenna, are all secondary means that can be used. It may be necessary to perform combinations of both radio changes (retuning, occupied bandwidth reduction) and antenna system changes (position, polarization, upgrade).

The EX-4.9r and EX-4.9r-c radios operate under licensed regulations. If interference is suspected, the local frequency coordination organization, or other users of the spectrum should be consulted before re-tuning the radio to a different frequency channel.

Path ObstructionA path obstruction is defined as an object, such as a building or tree, impeding the proper path of the radio system. If the system design was proper at the time of installation and issues arise at a later date, an updated path profile and survey may be necessary to identify changes in path clearance.

Misaligned AntennaAt the time of initial installation, it is critical that the antennas at each end are properly aligned and that the designed RSL is achieved. However, antennas may become misaligned due to high winds, changes in the guy-wiring systems keeping the antenna mast stable, or loosening of the antenna mounting hardware. A reduction in the RSL of the link is symptomatic of this condition, but this condition is not the only condition that results in a reduction of RSL. However, if conditions occur where the antenna alignment may be suspected, the mechanics must be inspected and the antennas realigned.

Faulty Antenna (EX-4.9r-c, EX-5r-c, and EX-5r-c IP)A faulty antenna is rare, but is still a possibility. In some cases, the mechanics of the antenna feed can get moisture inside, or a bad or weak connection in the pin and connector structure of the antenna may occur. A VSWR measurement of the antenna connection can be made to verify this condition.

Note: Exalt Digital Microwave Radios operate in license-exempt bands. Microwave ovens, wireless Internet devices and cordless phone technology may also use this frequency band. It may be necessary to separate the radio chassis, cabling system and antenna from these devices.


84 500000012008-05-09

Improper GroundingIn addition to being a potential human safety issue, improper system grounding is a somewhat common condition that can cause continuous bit errors or bit errors when metal objects come in contact with the radio, transmission system, or racking system. If touching the radio causes errors, grounding is the cause. It can be difficult to identify grounding problems, but a professional electrician can normally inspect a system and identify if there are deficiencies in the grounding system.

Insufficient Link MarginIdeally, the link was designed with enough link margin (fade margin) to allow for multipath propagation and atmospheric fading and still remain reliable. In some cases, link margin is compromised by economic factors, such as using low-cost RF cabling or lower-cost antennas that have less gain or deficient performance compared to higher cost transmission system components. In some cases, there may be antenna size restrictions that forced the design to not have the desired amount of link margin.

If the link was designed with poor link margin, there are likely many cases of bit errors and outages. The antenna system and transmission line can be upgraded to help reduce this. If the link design was installed with sufficient margin, but RSL is reduced, the remaining link margin may no longer be enough to maintain a reliable link. The causes of RSL reduction were previously described, but are usually due to new path obstruction(s) or antenna misalignment due to wind or mechanical factors. The antenna height or location can be changed to overcome new obstructions. Realignment of the antenna, and/or improvement to mechanical structures can help overcome antenna misalignment.

Moisture in the Transmission SystemIf the connectors on cables and antennas and egress junctions are not properly weatherproofed, moisture can get into the transmission system and cause significant error conditions and erratic performance. In many cases, the transmission system must be replaced. A VSWR meter is one means to identify such issues. Conduct physical inspections often. If changes to the weatherproofing (such as cracking) are noticed, replace the weatherproofing before leakage occurs.


50000001 852008-05-09

Back-to-back Bench TestingUse back-to-back bench testing to test the radio before installation, pre-configure the radio and connected equipment before installation, or in the troubleshooting process to identify if the radio hardware is the source of a system issue. It is a critical process, and often required or highly desirable for any installation or troubleshooting exercise. This section describes how to properly configure the radio hardware and accessories for a proper back-to-back bench test.

For radio testing, there are two types of back-to-back configurations:

1 Basic test (test general operation)

2 Specification performance verification

Basic TestThe basic test is a simple test of radio functionality. It verifies that the radios are properly configured to communicate to one another, and verifies general radio performance as operational.

For the basic test, the following items are needed:

• Radio pair

• Powering source

• RF interconnect cable(s) (any length – short is best)

• Fixed or variable attenuation, between 60 and 90dB (note: attenuation for basic test does not to be calibrated or precise)

• Computer/terminal with either serial or Ethernet port (helpful, but not necessary)

– If no computer is available, use the temporary hardware configuration key or DIP switch, depending on radio model (see Initial Configuration and Back-to-Back Bench Test)

Connect the items as follows:

1 Connect attenuation and (known-good) RF cable(s) between radio pair, shown in .

2 Configure one radio as Radio A; the other as Radio B

3 Power on radio pair

Figure 44 Basic back-to-back bench test configuration

After connecting and powering on, observe the front panel LEDs to verify that the LINK and STATUS LEDs are green. If so, the radios are communicating and all radio-related alarm conditions are normal.


86 500000012008-05-09

It can be beneficial to have a computer to verify configuration in case of red LEDs or to pre-configure the radio as desired for operation. Follow the instructions in .

Specification Performance VerificationThe specification performance verification is a more detailed test that allows you to verify that the radio’s output power and threshold specifications are being met. This is typically a test that would only be performed in a troubleshooting scenario, but can be performed before installation to provide a detailed record or ensure radio performance before installation.

This test is identical to the basic test, but in place of the fixed attenuation, it requires the use of calibrated variable attenuation, or a set of calibrated fixed attenuators, or a combination of both, adding to a total attenuation value of 120dB, as measured at the operating frequency of the radio. In addition, a volt meter or computer is also required.

Connect the system as shown in Figure 44, using the combination of fixed and variable attenuation between the radio’s RF ports. Connect the volt meter to either radio’s RSL test point and associated reference ground connection.

In this test, it is desirable to use pre-tested RF cables, known to be good, and the insertion loss is known at the operating frequency. If the cables are short (6'/2m or less), you can estimate the loss, including connectors, to be less than 1dB each. The estimate of cable loss is critical to the overall confidence of the measurements made in this test.

There are two critical specifications that can be tested in this configuration:

• RF output power

• Radio receiver threshold

To measure transmitter output power, simply insert any value of attenuation between the radios between 60 and 90dB. Ensure that both RF output power settings are at maximum. Use the volt meter to measure RSL in both directions. The RSL measured value should match the appropriate value according to the inserted attenuation, such as:

RSL = RF Output Power – cabling losses – total attenuation

Verify output power by adjusting output power using the Exalt GUI (in administration mode) and evaluate the corresponding change to the RSL measurement.

For threshold testing, the key is to insert a measured amount of loss that is close to, but not exceeding the radio’s specified system gain. System gain is the difference between RF output power and receiver threshold. At your selected modulation and bandwidth settings, determine the specified threshold performance, and choose a value of attenuation (including cable losses) that adds to roughly 5 to 15dB less than the system gain.

For example, for the EX-2.4i, if the threshold for your measurement is -85dBm, the output power is +27dBm, so the system gain is 112dB. Choose a value of total attenuation in the range of roughly 100–105dB. Once this attenuation is inserted, verify RSL readings as in the first step, and then, using the GUI, reduce radio output power in 1dB steps until the receiving radio (the one whose output power not being adjusted) Link LED turns from green to yellow. This indicates that threshold has been reached. At this point, verify the equation for system gain using the new output power level setting and verify that the threshold performance is meeting or exceeding the published specification.

Note: Due to the variation of measurements and accuracies involved in this test, you may read a measurement that is 1dB to as much as 2dB off of the expected value. It should be of no concern unless the value is more than 3dB worse than expected.


50000001 872008-05-09

General Compliance and SafetyThe usage of radio transmission devices is subject to specific regulatory requirements governed by regional legislation. In most cases, the specific device must be authorized for use in a given country and must be installed and adjusted in accordance with specific radio-frequency settings and in a manner that has been authorized specific to the device itself in accordance with the specific location of the device. Some users may be completely or partially restricted from use of the device. Please consult local governmental agency/agencies for regulatory requirements before use, or contact Exalt or your Exalt authorized dealer for assistance.

Do not modify this device in any way without the express written consent of Exalt. Modification voids the manufacturer warranty, and may also be illegal in accordance to government regulations. In addition, there are no user-serviceable parts or assemblies inside the product housing. There may also be voltages, signals, and mechanisms within the device that could be harmful to human safety.

The mounting of this device and associated peripherals and connections (inclusive of antenna mast, antenna, cabling, egress, lightning protection devices, grounding, power, and so on) may be subject to regional requirements for health and human safety. A qualified professional installer and an electrician are highly recommended, and may be required by law.


88 500000012008-05-09

Dynamic Frequency SelectionDynamic Frequency Selection (DFS) may be required by regional legislation in some frequency bands to avoid causing interference to radar systems. Prior to the start of any transmission, the device equipped with DFS monitors the spectrum and is not permitted to transmit on a part of the spectrum that is already in use for radar transmissions for a period of 30 minutes. During operation of the device, the spectrum is continually monitored by the DFS to detect if radar begins transmission on a frequency that is being used by the device to transmit on. If the DFS software detects radar, the device must move off channel within a specified time period so that the device transmission does not interfere with the radar transmission. The device equipped with DFS is required to stay off that part of the spectrum for a minimum of 30 minutes, after which time the device may then check the spectrum for radar transmissions and begin transmitting if no radar is detected.


50000001 892008-05-09

Safety Notices1 Review this entire guide for important installation instructions BEFORE attempting to install this

product.

2 This product is intended to be installed, used, and maintained by experienced telecommunications personnel only.

3 Employ a properly licensed or authorized electrician to install or evaluate/certify the installation of all power and grounding related to the use of this equipment and all connected devices.

4 The device(s) shall only be connected to AC power sources provided by the supplier or to DC sources within the device specifications. Use a separate breaker circuit at the power source.

5 Lightning, surge protection devices, and earth grounding are required for most installations to ensure human safety. Consult a qualified electrician.

6 Servicing of this device should be performed by authorized personnel only. Do not disassemble this device. By opening or removing any covers you may expose yourself to hazardous energy parts. Incorrect reassembly of this product can cause a malfunction, and/or electrical shock, when the unit is subsequently used.

7 Do not connect or disconnect the power connection to the device when the power supply is plugged into an AC outlet. To connect, first connect the power connection to the device, and then apply power (or plug in) at the outlet. To disconnect, disengage power at the outlet or unplug, and then disconnect the direct connection to the device.

8 Do not insert any object of any shape or size inside this product at any time, whether powered or not. Objects may contact hazardous energy components that could result in a risk of fire or personal injury.

9 Liquids shall not come in contact with, or enter the inside of the device at any time.

10 Proper ventilation and/or airflow shall be provided surrounding the equipment. Items shall not come in contact with heat-sinking materials. Ensure that ambient operational and storage temperature specifications are maintained at all times.

11 Equipment is suitable for mounting on noncombustible surfaces only.

12 Do not move or alter the marking labels.

13 A CSU or similar isolating device is necessary between the equipment and the public telecommunications network. The equipment has not been evaluated for direct connection to the public telecommunications network.


90 500000012008-05-09

Regulatory NoticesThe following notices apply to the EX-5r, EX-5r IP, EX-5r-c, and EX-5r-c IP version radios and generally apply to the EX-4.9r versions.

4.9GHz ModelsThe EX-4.9r and EX-4.9r-c are licensed-band products operating within Part 90 of the FCC regulations and RSS-111 of Industry Canada. These bands are specifically reserved for Public Safety applications and related agencies, in accordance with these regulations.

Professional installation is required, and transmitter power reduction may be required, depending on transmission system gains and losses.

United States ComplianceThe r-Series product families operate under FCC Rule Parts 15.247 and/or 15.407 as a license-exempt device. The EX-4.9r products operate under FCC Rule Part 90 as a licensed device. They may only be used as a point-to-point transmission device for fixed or temporary-fixed (non-mobile) installations. The devices are subject to the following restrictions:

• Do not use external amplifiers to boost the power or overcome transmission system losses, unless the specific amplifier/cable/antenna combination has expressly been authorized by the FCC. The output power must never exceed +30 dBm.

• Cross-border transmissions are expressly prohibited, except with written permission from both the FCC and the governing body of the neighboring country (Cofetel for Mexico; Industry Canada for Canada).

• Use only parabolic dish antennas or directional flat-panel antennas. No other types of antennas (omni-directional, yagi, and so on) are authorized. Parabolic dishes of either grid or solid type are allowed. Maximum mid-band gain of each type of antenna certified is:

– EX-4.9r models:

– Parabolic dish: 26dBi (larger gains are allowed, with Tx power reduction)

– Directional flat panel: 26 dBi (larger gains are allowed, with Tx power reduction)

– EX-5r models:

– Parabolic dish: 37.9 dBi (6'/1.8m diameter)

– Directional flat panel: 28 dBi (~2'/61cm square)

Federal Communications Commission (FCC), United StatesThe device is allowed to be used provided it does not cause interference to other devices. It is not guaranteed to provide protection against interference from other electronic and radio devices.

The system has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures:


50000001 912008-05-09

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations.

Changes or modifications not expressly approved in writing by Exalt may void the user’s authority to operate this equipment.

This device must be professionally installed.To comply with regulations, the output power of this device may need to be adjusted in accordance to the associated transmission system. See RF Output Power Setting for details.

The antenna associated with this device shall be mounted in a location that is at least 10.5'/3.2m away from humans that may be subject to long-term or continuous exposure.

Canada ComplianceThe EX-5r models operate under RSS-210 of Industry Canada regulations. The EX-4.9r models operate under RSS-111 of Industry Canada regulations. Operation is subject to the following conditions, unless express permission is granted by Industry Canada to operate in a different manner:

• External amplifiers cannot be used to boost the power or to overcome transmission system losses, unless the specific amplifier/cable/antenna combination is expressly authorized by Industry Canada.

• Cross-border transmissions are expressly prohibited, except with written permission from both Industry Canada and the governing body of the neighboring country (FCC for USA)

• Only parabolic dish antennas or directional flat-panel antennas may be used. No other types of antennas (omni-directional, yagi, and so on) are authorized. Parabolic dishes of either grid or solid type are allowed. Maximum gain of each type of antenna allowed is:

– EX-4.9r models:

– Parabolic dish: 26 dBi (larger gains are allowed with Tx power reduction)

– Directional flat panel: 26 dBi (larger gains are allowed with Tx power reduction)

– EX-5r models:



Industry Canada (IC), CanadaThis Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.


92 500000012008-05-09

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:

1 this device may not cause interference, and

2 this device must accept any interference, including interference that may cause undesired operation of the device.

Antennas Supported in CanadaThe EX-5r Series radios are designed to operate with the antennas listed in Table 7, which have a maximum gain of 37.5dBi. Antennas not included in the list or having a gain greater than 37.5dBi are strictly prohibited for use with this device. The required antenna impedance is 50 Ohms.

Europe and ITU Country ComplianceAll of these permitted devices must be professionally installed. They can only be used as a point-to-point transmission device for fixed or temporary-fixed (non-mobile) installations.

The EX-4.9r devices are currently not permitted in any EU member or affiliate countries.

The EX-5r product family operates under EN 301 893 and EN 302 502 rules as a license-exempt device.

The EX-5r product family complies with ETS 301 893 for the 5.3 and 5.47 GHz bands for license-exempt use for most countries recognizing ETSI or ITU band assignments. This band is not yet harmonized for all countries recognizing ETSI or ITU band assignments. These bands require Dynamic Frequency Selection (DFS) and Transmitter Power Control (TPC) for radar-detection and avoidance. There is a +30dBm EIRP limit applied to this band. Transmitter power must be adjusted accordingly with respect to the RF cabling losses and antenna gains associated with each terminal.

The EX-5r product family complies with ETS 302 502 for the 5.8 GHz band. This band is not yet harmonized for all countries recognizing ETSI or ITU band assignments. Consult the individual country regulations or your Exalt Communications representative for details. This band requires DFS and TPC for radar-detection and avoidance. There is a +33dBm EIRP limit for use of the 10 MHz BW setting, and a +36dBm EIRP limit for use of the 20 MHz BW setting. Some countries limit the EIRP to +5dBm for all bandwidths in this band.

All models comply with the requirements for CE Mark (EN 60950-1 and IEC 60950-1) and EMC (EN 301 489-17). No substitutions shall be made, and all wiring and grounding instructions contained in this manual must be followed to ensure safety in accordance to the standards and local rules.

Note: Do not use external amplifiers to boost the power or overcome transmission system losses, unless the specific amplifier/cable/antenna combination has expressly been authorized by the specific country regulations. The output power must never exceed that specified in Specifications.


50000001 932008-05-09

Regulatory ComplianceAs of this printing, Exalt Communications, Inc. has approvals for the products that are covered by this manual, as indicated in Table 8. If your application or country is not listed, check with your Sales Representative for the current status.

Table 8 Product Approvals

Country EX-4.9r Series EX-5r Series, 5.3 GHz EX-5r Series, 5.4 GHz EX-5r Series, 5.8 GHz

Austria

Australia

Belgium

Canada

Cyprus

Czech Republic

Denmark

Estonia

Finland

France

Germany

Ghana

Great Britain

Hungary

Iceland

Ireland

Italy

Liechtenstein

Lithuania

Luxembourg

Malta

Mexico

Netherlands

Norway

Philippines

Poland

Portugal


94 500000012008-05-09

Romania

Slovak Republic

Slovenia

Spain

Sweden

Switzerland

Turkey

United States

Table 8 Product Approvals (Continued)

Country EX-4.9r Series EX-5r Series, 5.3 GHz EX-5r Series, 5.4 GHz EX-5r Series, 5.8 GHz


50000001 952008-05-09

Regulatory Domain KeysExalt radios are designed to allow the professional installer to select frequency bands, determine signal bandwidths, tune center frequencies, limit output power, and enable or disable DFS options as permitted by regional regulations. For models with the Regulatory Domain Key (RDK) feature, the radios ship with the RDK information empty and the radio cannot be enabled without a valid key. The partner, distributor, or installer is responsible for installing the RDK based on the final installation country of the radio. Exalt issues RDK information to their distributors when ship-to country information is provided. Consult your local Exalt distributor or reseller to obtain the RDK.

Countries are assigned to different regulatory domains based on current regulatory requirements. Each regulatory domain has the parameters set to ensure that when the radio is turned on, the default settings are complaint for local laws.

Regulatory Domain Keys are assigned by regulatory domain based on the local regulations.

Caution! It is critical that the RDK be set to the correct default setting so that the local regulations for the installation requirements are met.

Table 9 Regulatory Domain KeysRegulatory Domain Key Name

Frequency Band(s) Countries

049A0 4.9GHz USA, Canada

053A0 5.3GHz, 5.4GHz, 5.8GHz

USA (prior to July 20, 2007), Canada (prior to May 8, 2008), Singapore, Philippines

053A1 5.3GHz, 5.4GHz, 5.8GHz

USA (after July 20, 2007), Canada (after May 8, 2008)

053A2 5.8GHz China

053A3 5.3GHz, 5.8GHz

Mexico

053A4 5.3GHz, 5.4GHz, 5.8GHz

EU, Ghana

053A5 5.4GHz, 5.8GHz

Australia

053A6 5.3GHz, 5.4GHz, 5.8GHz

Philippines


96 500000012008-05-09

EIRP Limits for the United States and Canada

EX-4.9r EIRP for the USA and CanadaFor the EX-4.9r models, within the 4940–4990 MHz band, the maximum EIRP allowed is +50dBm. The maximum output power of the radio shall never exceed +24dBm.

For the EX-4.9r models, the transmit power must be reduced from maximum (+24dBm for 20MHz BW; +22dBm for 10MHz) by 1 dB for every 1dB that the antenna gain exceeds 26dBi (including transmission system losses)

EX-5r Series EIRP for the US and Canada

5250–5350 MHz Band

For all within the 5250–5350 MHz band, the maximum EIRP is 30 dBm. The maximum output of the radio is +13 dBm.

P = 30 – G + Lwhere:

5470–5725 MHz Band

For all models within the 5470–5725 MHz band, the maximum EIRP allowed is 30 dBm. The maximum output power of the radio is +13 dBm.


5725–5850 MHz Band

For all models within the 5725–5850 MHz band, the maximum EIRP allowed is 61.9 dBm. The maximum output power of the radio is +24 dBm in Mode 1 and +21 dBm in Mode 2.

P = 61.9 – G + L

Note: The professional installer is responsible to ensure that RF output power is properly adjusted to not exceed the regulatory limit.

P = Maximum transmitter output power of radio, in dBm.G = Specified gain of antenna, in dBi, from 5250 to 5350 MHz.L = Total transmission system losses of all elements between the radio’s RF connector and the

antenna’s RF connector (all cables, connectors, lightning suppressors), in dB, as specified or measured between 5250 and 5350 MHz.




50000001 972008-05-09

where:




98 500000012008-05-09

EIRP Limits for Australia

EX-5r Series EIRP for Australia

5470–5725 MHz Band

For EX-5r models within the 5470–5725 MHz band, the maximum EIRP allowed is 30 dBm. The maximum output power of the radio is +13 dBm.


5725–5850 MHz Band

For the EX-5r models within the 5725–5850 MHz band, the maximum EIRP allowed is 36 dBm. The maximum output power of the radio is +24 dBm in Mode 1 and +21 dBm in Mode 2.



Note: Australian regulations have a no-transmit band from 5600–5650 MHz, adjust the transmitter to avoid this range.






50000001 992008-05-09

EIRP Limits for the European Union and ITU CountriesThe countries that are covered by this Regulatory Domain are: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Ghana, Great Britain, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Norway, Poland, Portugal, Slovak Republic, Slovenia, Spain, Sweden, Netherlands, Switzerland, and Turkey.

• Use only parabolic dish antennas or directional flat-panel antennas. No other types of antennas (omni-directional, yagi, and so on) are authorized. Parabolic dishes of either grid or solid type are allowed. Maximum mid-band gain of each type of antenna certified is:

– EX-5r models:



EX-5r Series EIRP Table 10 summarizes the maximum power by band and country for EX-5r Series radios.

5250–5350 MHz band

For all models within the 5250–5350 MHz band, the maximum EIRP is specified in Table 10. The maximum output of the radio is +13 dBm.

P = ME – G + Lwhere:

5470–5725 MHz band

For all models within the 5470–5725 MHz band, the maximum EIRP allowed is specified in Table 10. The maximum output power of the radio is +13 dBm.



P = Maximum transmitter output power of radio, in dBm.

ME = Maximum EIRP, as specified in Table 10.

G = Specified gain of antenna, in dBi, from 5250 to 5350 MHz.

L = Total transmission system losses of all elements between the radio’s RF connector and the antenna’s RF connector (all cables, connectors, lightning suppressors), in dB, as specified or measured between 5250 and 5350 MHz.


100 500000012008-05-09

5725–5850 MHz band

For all models within the 5725–5850 MHz band, the maximum transmit power with respect to specific country EIRP regulations is determined based on the channel bandwidth. The EIRP power limit is specified in Table 10. The Exalt EX-5r series radios maximum transmitter conducted power is +24 dBm. Use the following equation to determine the maximum transmitter power for the radio:


P = Maximum transmitter output power of radio, in dBm.ME = Maximum EIRP, as specified in Table 10.G = Specified gain of antenna, in dBi, from 5470 to 5725 MHz.L = Total transmission system losses of all elements between the radio’s RF connector and the


P = Maximum transmitter output power of radio, in dBm.ME = Maximum EIRP, as specified in Table 10.G = Specified gain of antenna, in dBi, from 5725 to 5850 MHz.L = Total transmission system losses of all elements between the radio’s RF connector and

the antenna’s RF connector (all cables, connectors, lightning suppressors), in dB, as specified or measured between 5725 and 5850 MHz.


50000001 1012008-05-09

Table 10 EU and ITU Country Specific EIRP Levels for EX-5r Series

Country Maximum EIRP 5.3 GHz band Maximum EIRP 5.4 GHz bandMaximum EIRP 5.8 GHz band(BW dependent)a

a. If the output power is designated as 33/36 dBm, the EIRP is limited to 33 dBm for 10 MHz bandwidthtransmissions and 36 dBm for 20 MHz bandwidth transmissions.

Austria 23 dBm 30 dBm 5 dBm

Belgium 30 dBm

Cyprus 23 dBm 30 dBm

Czech 23 dBm 30 dBm 33/36 dBm

Denmark 23 dBm 30 dBm 33/36 dBm

Estonia 23 dBm 30 dBm

Finland 23 dBm 30 dBm

France 23 dBm 30 dBm 33/36 dBm

Germany 23 dBm 30 dBm 33/36 dBm

Ghana 23 dBm 30 dBm 33/36 dBm

Great 23 dBm 30 dBm 33/36 dBm

Hungary 23 dBm 30 dBm 33/36 dBm

Iceland 23 dBm 30 dBm 33/36 dBm

Ireland 23 dBm 30 dBm 33/36 dBm

Italy 23 dBm 30 dBm 33/36 dBm

Liechtens 23 dBm 30 dBm 5 dBm

Lithuania 23 dBm 30 dBm 33/36 dBm

Luxembo 23 dBm 30 dBm

Netherla 23 dBm 30 dBm 33/36 dBm

Norway 23 dBm 30 dBm 33/36 dBm

Poland 23 dBm 30 dBm 33/36 dBm

Portugal 23 dBm 30 dBm 5 dBm

Romania 23 dBm 30 dBm 33/36 dBm

Slovak 23 dBm 30 dBm 5 dBm

Slovenia 23 dBm 30 dBm

Spain 23 dBm 30 dBm 33/36 dBm

Sweden 23 dBm 30 dBm 33/36 dBm

Switzerla 23 dBm 30 dBm 5 dBm

Turkey 23 dBm 30 dBm 33/36 dBm


102 500000012008-05-09

Declaration of Conformity to the R&TTE Directive1999/5/EC

For 5 GHz radios, the following standards were applied:

• Radio: EN 301 893, EN 302 502

• EMC: EN 301 489-1, EN 301 489-17

• Safety: EN 60950-1, IEC 60950-1

The following CE mark is affixed to the product:

EU WEEEExalt is committed to meeting the requirements of the European Union’s Waste Electrical and Electronic Equipment (WEEE) Directive. The Directives require producers of electrical and electronic equipment to finance the take-back for re-use or recycling of their products placed on the EU market after 13 August 2005.

Exalt products that are within the scope of the Directives are labeled with a crossed-out "wheelie-bin" symbol as required by the Directives. This indicates that the product was placed on the market after 13 August 2005 and that end-users should segregate the product from other wastes at end-of-life.

The WEEE Directives are being implemented in each of the 28 EU and European Economic Area (EAA) countries through national legislation. This has resulted in considerable variation in the detailed requirements across the EU, many of which require presence in the EU. As a result, Exalt’s WEEE compliance approach is to require the distributors and/or resellers in the EU to comply with each country’s national legislation by registration of the distributor or reseller as the producer and for the reseller/distributor to carry out and fulfill the legislative requirements of each national compliance scheme.

Below is the crossed out wheelie bin symbol as required by the WEEE Directive.

English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Deutsch: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden Vorgaben der Richtlinie1999/5/EU.

Dansk: Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Directiv 1999/5/EF.

Español: Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directive 1999/5/EC.

Français: Cet appareil est conforme aux exigencies essentialles et aux autres dispositions pertinantes de la Directive 1999/5/EC.

Íslenska: Þessi búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipunar 1999/5/ESB.

Italiano: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/EC.

Nederlands: Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijn 1999/5/EC.

Norsk: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-directiv 1999/5/EC.

Português: Este equipamento satisfaz os requisitos essenciais e outras provisões da Directiva 1999/5/EC.

Suomalainen: Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimukset ja on siinä asetettujen muidenkin ehtojen mukainen.

Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.


50000001 1032008-05-09

EU RoHSRoHS is the acronym used to refer to the European Union (EU) Directive 2002/95/EC on the Restriction of the use of certain hazardous substances in electrical and electronic equipment. Hazardous materials are those chemicals and substances that are legislatively, market, or customer banned or restricted for use in products and/or manufacturing. There are six (6) RoHS substances: lead (Pb), cadmium (Cd), mercury (Hg), hexavalent chromium (Cr+6), polybrominated biphenyls (PBB) and polybrominated diphenylethers (PBDE). Other countries may be introducing legislation that results in similar restrictions of hazardous substances. Many Exalt products will continue to use lead-based solder under the exemption allowed for network infrastructure equipment. Small amounts of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE can also be found in a few electrical and electrical components.


104 500000012008-05-09

Exalt Limited Hardware WarrantyExalt Communications, Inc. (“Exalt”) warrants solely to the original purchaser (“Purchaser”) that the EX-4.9r, EX-4.9r-c, EX-5r, EX-5r IP, EX-5r-c, or EX-5r-c IP (the “Product”) will substantially conform in all material respects to the relevant Exalt published specifications that apply at the time of manufacture of such Product for two (2) years from the date of tender of Product by Exalt from FOB point designated by Exalt (the “Warranty Period”). Proof-of-purchase in the form of an invoice, payment of invoice, or delivery waybill must be supplied, if requested by Exalt, in case of any dispute of warranty start date. Exalt shall within the Warranty Period, at its own option: (A) use reasonable efforts to remedy any reproducible Product defect covered by this limited warranty within a reasonable period of time; (B) replace the defective Product with a functionally equivalent product (repair parts and products may be either reconditioned or new, but, if reconditioned, shall be of the same quality as new parts or products); or (C) if Exalt determines that it is unable to repair or replace such Product, Exalt will refund to Purchaser the amount actually paid by Purchaser for the applicable Product. All replaced parts become the property of Exalt. Exalt may, at its sole option, refuse to accept as defective Product that (i) is subject to the exclusions set forth below; or (ii) cannot be demonstrated to be defective by Exalt and Purchaser is unable to provide adequate information describing how the Product failed. Such Product will, at Purchaser’s option and expense, either be: (a) returned to Purchaser in the state received, or (b) repaired and returned to Purchaser. Repaired or replaced Product will be warranted for the remainder of the original Warranty Period, but not less than ninety (90) days.

RegistrationPurchaser is required to register its Product, within ninety (90) days of purchase, for full warranty support. Unregistered or late-registered Product will receive a Warranty Period of only one (1) year.

ExclusionsThis limited warranty will not apply to: (A) any Product that: (i) has been modified or altered by any party other than Exalt; (ii) has been subject to accident, misuse, abnormal wear and tear, neglect, or mistreatment; (iii) has been damaged during installation of the Product; (iv) has been damaged by the equipment or system with which the Product is used; (v) has sustained damage to the Products’ interface or power connectors; (vi) are determined to be stolen; or (vii) has been damaged caused by fire, power changes, other hazards, or acts of God (including without limitation lightning); or (B) any software included in any such Product. The warranty applies only to Products that can be identified by the Exalt trademark, trade name, serial number or logo affixed to them. Exalt does not warrant any Product that is not manufactured by, for, or with permission from Exalt. The Products covered by this warranty are not consumer products and are not intended for personal, family, or household purposes.

RMA ProceduresA return material authorization (RMA) is required prior to returning Product to Exalt for warranty or out-of-warranty repair/evaluation. As such, Purchaser must use the following procedure:

1 Contact Exalt and request an RMA number. Please be prepared to provide the serial number of the Product, the date of purchase, and a description of the failure that is as complete as possible.

2 Pack the Product in its original container and packing or an equivalent.

3 Write the RMA number CLEARLY on the outside of the shipping box.

4 For services during the Warranty Period, cost of shipment to Exalt’s authorized service center, taxes, duty, tariffs, risk of loss and insurance charges to Exalt shall be borne by the Purchaser. Cost


50000001 1052008-05-09

of return shipment and insurance charges shall be borne by Exalt and will be made by Exalt’s choice of carrier and method/schedule of shipment. Purchaser may expedite return shipments, upon request, at its own expense.

PRODUCTS RETURNED WITHOUT A DULY ISSUED RMA NUMBER WILL BE RETURNED TO PURCHASER AT PURCHASER’S EXPENSE.

THIS EXPRESS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, REGARDING THE PRODUCT, AND EXALT, ITS SUPPLIERS AND LICENSORS HEREBY EXPRESSLY DISCLAIM ALL SUCH IMPLIED AND EXPRESS WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE, TITLE, INTERFERENCE WITH QUIET ENJOYMENT, NON-INFRINGEMENT OF THIRD-PARTY RIGHTS AND MERCHANTABILITY. FURTHER, EXALT DOES NOT WARRANT RESULTS OF USE OR THAT PURCHASER’S USE OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. NO WARRANTIES ARE MADE BY EXALT’S SUPPLIERS OR LICENSORS. EXCEPT FOR THE EXPRESS WARRANTY STATED HEREIN, THE PRODUCT IS PROVIDED “AS IS” AND WITH ALL FAULTS. THE ENTIRE RISK AS TO SATISFACTORY QUALITY, ACCURACY, AND EFFORT IS WITH PURCHASER.


106 500000012008-05-09

Copyright NoticesThis section presents copyright notices for third-party software licensed to Exalt Communications, Inc.

Net-SNMP

The following copyright notice applies to the open-source licensing agreement for Net-SNMP.

Copyright 1989, 1991, 1992 by Carnegie Mellon University

Derivative Work - 1996, 1998-2000

Copyright 1996, 1998-2000 The Regents of the University of California

All Rights Reserved

Permission to use, copy, modify and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appears in all copies and that both that copyright notice and this permission notice appear in supporting documentation, and that the name of CMU and The Regents of the University of California not be used in advertising or publicity pertaining to distribution of the software without specific written permission.

CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

Network Associates Technology, Inc.

Copyright (c) 2001-2003, Networks Associates Technology, Inc

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

* Neither the name of the Networks Associates Technology, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,


50000001 1072008-05-09

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Cambridge Broadband, Ltd.

Portions of this code are copyright (c) 2001-2003, Cambridge Broadband Ltd.





* The name of Cambridge Broadband Ltd. may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Sun Microsystems, Inc.

Copyright © 2003 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara,

California 95054, U.S.A. All rights reserved.

Use is subject to license terms below.

This distribution may include materials developed by third parties.

Sun, Sun Microsystems, the Sun logo and Solaris are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.




* Neither the name of the Sun Microsystems, Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.


108 500000012008-05-09

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Sparta, Inc.

Copyright (c) 2003-2005, Sparta, Inc





* Neither the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.


Cisco, Inc.

Copyright (c) 2004, Cisco, Inc and Information Network

Center of Beijing University of Posts and Telecommunications.





50000001 1092008-05-09


* Neither the name of Cisco, Inc, Beijing University of Posts and Telecommunications, nor the names of their contributors may be used to endorse or promote products derived from this software without specific prior written permission.


Fabasoft R&D Software GmbH & Co.

Copyright (c) Fabasoft R&D Software GmbH & Co KG, 2003

[email protected]

Author: Bernhard Penz





110 500000012008-05-09

IndexAAC adapter 24Administration Settings page 39administrator privileges 33Advance Encryption Standard 40AES 40AIS enabling//disabling 51alarm conditions 36alarms 48, 59

clearing 63Alarms page 59AMI 51antenna port parameter 46antennas

alignment 30, 84Canada 93mounting 5, 27

indoor 29mounting height 7site preparation considerations 7transmission line 28troubleshooting 84

BB8ZS 51back-to-back bench test 9, 86back-to-back bench test configuration 86bandwidth 6Bandwidth parameter 44battery source 24BER 64browsers 31buzzer timeout selection parameter 47Ccables

Ethernet (CAT5) 9RF 7RFC 6T1/E1 9troubleshooting

improper RF cable termination 83center frequency tuning 6channel bandwidth 6CLI 31

main menu 31menu options 31

configuration file 54

connectors 22GPS/RSL 22Power/Ethernet 22, 78T1/E1 1&3 22T1/E1 2&4 22TDM 77

contact information 3Current BER field 61Current RSL field 61Ddata communication interface 6date and time 39DC power source 24Diagnostic Charts page 64dimensions 70documentation, related 3duplex settings 48Dynamic Frequency Selection (DFS) 45, 89EE1 channels 52E1 Interface Configuration page 52effective isotropic radiated power (EIRP) 10encryption 6Endpoint Identifier 34, 43Errored Seconds (ES) field 62Ethernet configuration parameters 52Ethernet connectors 78Ethernet interface 76

throughput settings 51Ethernet Interface Configuration page 48Event Log page 63ExaltCalc tool 11, 82external loopback modes 53Ffactory default settings 26, 55fade margin 7, 85features 6File Activation page 55, 57File Transfer page 54file transfers 54files

activating stored 57default configuration file 55

flywheeling 15frame length See TDD framefrequency


50000001 1112008-05-09

center 7Ggateway (default) 56Global Positioning System (GPS) kit 13GPS Information page 58GPS synchronization 46, 58GPS/RSL connector 22GPS/RSL LED 23grounding 85GUI

Administration Settings page 39Alarms page 59browsers supported 31description 31Diagnostic Charts page 64E1 Interface Configuration page 52Ethernet Interface Configuration page 48Event Log page 63File Activation page 55, 57File Transfer page 54GPS Information page 58IP address (default) 32log in 32login privileges 33navigation panel 36Performance page 61Radio A configuration 32Radio Information page 38Reboot page 68Spectrum Analyzer page 66summary status information 35System Configuration page 43T1 Interface Configuration page 51T1/E1 Configuration page 51VLAN page 49

Hhop 8hub 13Iinterfaces

Ethernet 76power 76RF 76T1/E1 76

interference 62interference profile 7IP address conflicts 32

IP address subnet 32IP settings 9Kkeys

Regulatory Domain Key (RDK) 40, 43LLEDs

GPS/RSL 23Power Injector 23Power/Ethernet 23T1/E1 1&3 23T1/E1 2&4 23

License Key 40lightning arrestor 7lightning arrestors 29Line Build Out (LBO) 51Line Code 51link 7

orientation 11RF link testing 9synchronization 11

Link Distance parameter 45link margin 85link parameters 35Link Security Key 39Link Security Key parameter 56login names 33login privileges 33loopback 51, 52, 53

external (local) 53external (remote) 53internal 53

MMaximum RSL field 62MIB files 54Minimum RSL field 62Minimum RSL Timestamp field 62Mode parameter 44mounting

hardware 20multi-link network 14multipath 82multipath propagation 83muting 48Nnoise profile 7


112 500000012008-05-09

Ooffset timing 14Pparameters

antenna port 46buzzer timeout selection 47

passwords 9, 33path obstruction 84performance degradation 82Performance page 61power

system LEDs 25Power connector 78power injector 24power interface 76Power/Ethernet connector 22Rradio

default settings 12grounding 85initiation tasks 18installation tasks 18maximum transmit power setting 44mounting 7, 20rebooting 63, 68warranty 105

Radio A 12Radio A configuration 8radio configuration 8radio features 6radio firmware files 54radio frequency 4Radio Information page 38radio mount

enclosure 5connections 6

indoor 5connections 5

Radio Transmit Power parameter 43Reboot page 68receiver threshold 7record keeping 19Regulatory Domain Database (RDD) 54Regulatory Domain Key (RDK) 40, 43, 96regulatory requirements

EX-4.9r FCC EIRP 97EX-5i FCC EIRP 99

EX-5r Series FCC EIRP 97USA 91

repeater 13RESET button 23RF cable length 6RF connector termination 24RF Frequency parameter 44RF interface 76RF interference 83RF lightning arrestor 29RF output power 10RSL 10

current RSL readings 61diagnostics 64Maximum RSL field 62Minimum RSL Timestamp field 62monitor for performance 82

RSL voltage 30Ssafety 88Set to E1 button 51Set to T1 button 51shipping box contents 8site preparation 7SNMP 16, 41specifications 70Spectrum Analyzer page 66Swap button 55, 57sync source 15synchronization 13System Configuration page 43system latency 7system parameters

default settings 26system performance 61system reboot 63system settings

Current BER field 61Errored Seconds (ES) field 62grounding 85Maximum RSL 62Minimum RSL field 62Time Since Reset field 62Unavailable Seconds field 62

system specifications 71TT1 clocking 23


50000001 1132008-05-09

T1 Interface Configuration page 51T1/E1 1&3 connector 22T1/E1 2&4 connector 22T1/E1 2&4 LED 23T1/E1 circuits 51T1/E1 Configuration page 51T1/E1 interfaces 76T1/E1 loopback 53TDD factors 10TDD frame length 7TDD Frame Size parameter 45TDM circuits 44TDM connections 77TDM connectors 77Telnet session 31temperature 64testing 86

back-to-back bench 9threshold 87

threshold testing 87time division duplex (TDD) SeeTDD frameTime Since Reset 62timing, offset 14transmission line

coaxial 28transmitter

output power 9troubleshooting 64, 81UUnavailable Seconds (UAS) 62unfaded error-free performance 10Update button 39user privileges 33VVLAN 15

tagging 15VLAN page 49voltage test 30VSWR 83Wwarranty 105

500000012008-05-09

General Specifications



SP2-5.20.6 m | 2 ft Standard Performance ParabolicReflector Antenna, Single-polarized, 5.25-5.85GHz

Antenna Type Standard Performance Parabolic Reflector Antenna

Size, nominal 2 ft | 0.6 m

Polarization Single

Operating Frequency Band 5.25 - 5.85 GHz

Half Power Beamwidth, Horizontal 6.1 degrees

Half Power Beamwidth, Vertical 6.1 degrees

Cross-Polarization Discrimination 28 dB

Front to Back Ratio (F/B) 38 dB

Gain, Low Frequency 28.5 dBi

Gain, Mid Frequency 29 dBi

Gain, High Frequency 29.5 dBi

VSWR 1.5:1

Return Loss -14 dB

Fine Azimuth Adjustment +/- 10 degrees

1

Regulatory Compliance

Shipping Information

Additional Comments

Technical Drawings

Fine Elevation Adjustment +/- 30 degrees

Mounting Pipe Diameter, Min 2 inch | 5.08 cm

Mounting Pipe Diameter, Max 4.5 inch | 11.4 cm

Net Weight 22 lbs | 9.9 kg

Wind Velocity Operational 90 mph | 145 km/h

Wind Velocity Survival Rating 125 mph | 201 km/h

Mechanical Configuration SP2

Axial Force (FA) 222 lbs | 988 N

Side Force (FS) 14 lbs | 62 N

Twisting Moment (MT) 225 ft-lbs | 305 Nm

Operating temperature range -40 to +60 C

Max pressure, psig, (if waveguideinterface)

5

FCC undeclared

ETSI undeclared

RoHS-complaint Yes

Package Type Cardboard

Gross Weight 25 lbs | 11.3 kg

Dimensions, L x W x H 28 x 8 x 28in | 71 x 20 x 71 cm

Shipping Volume 3.63 cu ft | 0.1 cu m

Note that all 5.2 models will operate 4.9-6.0 GHz with slightly degraded specifications

2

Radiowaves Glossary

Axial Force: Force applied to the face of the antenna due to wind at specified wind speed

Beamwidth The total width of the main beam measured in degrees between the 3-dB (half-power)points on either side of the peak of the main beam

Cross Polarization Discrimination (XPD) The dB difference between maximum received co-polarized signal at electrical boresightand maximum received cross-polarized signal

Front to Back Ratio (F/B) The dB difference between maximum received signal at electrical boresight to maximumreceived signal behind the antenna (180 +/- 40 degrees)

Gain A measure of how well the antenna focuses available energy into a single beam. Largerantennas typically have higher gains and smaller beamwidths.

Gross Weight Shipping weight, includes weight of antenna plus packaging materials

Net Weight Weight of antenna only as mounted on tower.

Operating Frequency Band The frequency limits between which the antenna meets declared specifications. Antennasmay operate outside the frequency band with mild performance degradation.

Return Loss A measure of how much rf energy incident upon the antenna is reflected back fromwhence it came, expressed as a negative dB value.

Side Force (FS) Force applied to the side of the antenna due to wind at specified wind speed

Twisting Moment (MT) The torsional (twisting) moment (force x distance) applied to the mounting pipe due towind at the specified wind speed.

3

VSWR A measure of how much rf energy incident upon the antenna is reflected back fromwhence it came, expressed as a ratio

Wind Velocity Operational Wind speed where the antenna deflection is less than or equal to 0.1 degrees

Wind Velocity Survival Rating Wind speed where the antenna will not suffer permanent damage, but may require re-pointing.

4

Documents

Maricopa County Community College District. South … E...Antenna Orientation: KJZZ ERI SHPX‐12AC‐HW 51 Degrees True KBAQ ERI MP‐10AC‐DA‐HW 1 – 3 Degrees True, Actual to