OPERATING INSTRUCTIONS

Page 2 of 16

CONTENTS

1 Runtastic Speed & Cadence Sensor incl. lithium battery

(3 V, CR2032, Art. No.: RUNSCS1, Model: BSCBLE)

4 tools for assembly

SPOKE MAGNET

CABLE TIE

SPOKE

MAGNET PEDAL MAGNET

RUBBER CLAMP

Page 3 of 16

ELECTROMAGNETIC COMPATIBILITY Very strong magnetic fields (e.g. transformers) should be avoided, since they may cause distortions of the transmission signals. Non-compliance with this information may lead to defects in or damage to your Runtastic Speed & Cadence Sensor.

RISKS FOR CHILDREN AND PEOPLE IN NEED OF CARE

This device is not intended for use by children aged eight (8) upwards and individuals with limited physical, sensorial or emotional capacities or limited experience and / or knowledge unless they are super-vised by an individual responsible for their safety or receive instruc-tions from the latter as to how the device should be used and have understood the dangers arising from it. Children should be super-vised in order to ensure that they do not play with the device. Cleaning and user maintenance may not be performed by children without su-pervision.

Page 4 of 16

BATTERY OPERATION

Your Runtastic Speed & Cadence Sensor uses a lithium battery (3 V, CR2032).

Here is some information about handling of batteries: Only replace a battery with a

battery of equal rating and qual-ity.

Batteries must not be charged or reactivated by any other means; they must not be opened, thrown into a fire or short-circuited.

Always store batteries out of the reach of children. If swallowed, batteries may be fatal. Store the batteries and the Runtastic Speed & Cadence Sensor out of reach of babies and toddlers. If a battery has been swallowed, immediately seek medical atten-tion.

Never expose the batteries to excessive heat, such as solar radiation, fire, etc. This can in-crease the risk of leakage. Non-

Page 5 of 16

compliance with this information may lead to damage and, under certain circumstances, even ex-plosion of the batteries.

Promptly remove an empty bat-tery from the Runtastic Speed & Cadence Sensor. Otherwise, it runs the risk of leaking. If a bat-tery is leaking, avoid contact with your skin, eyes, and mucus. Immediately rinse all parts of your body that came into con-tact with battery acid using plenty of clean water and seek medical attention. If required, clean the battery contacts and mating contacts in the device. Keep the instruction manual in a safe place to be able to look up information, including battery in-formation. Non-compliance with these notes may lead to damage and, under certain circumstances, even explosion of the batteries. For information about replace-ment of the battery for the Runtastic Speed & Cadence Sensor read the section "Battery

Page 6 of 16

replacement in the Runtastic Speed & Cadence Sensor".

DISPOSAL

Batteries are classified as hazardous waste. For cor-rect disposal of batteries, suitable containers are pro-vided in battery-selling shops and at municipal waste collection points.

If you want to dispose of your Runtastic Speed & Cadence Sensor, please comply with the currently valid local rules and regulations. Obtain information from the compe-tent municipal body. KRIPPL-WATCHES Warenhandels GmbH Maria-Theresia-Straße 41, 4600 Wels, Austria Dispose of packaging in compliance with currently valid rules and regulations.

Page 7 of 16

Obtain information from the compe-tent local municipal body. FUNCTIONS AND USE

For transmission of cycling speed and cadence from your Runtastic Speed & Cadence Sensor to your smartphone, the latest Bluetooth technology is used. I.e. smartphones with Bluetooth® Smart and Bluetooth® Smart ready are compatible. An up-to-date list of all compatible smartphones is provided at

Runtastic.com/products

GETTING STARTED 1. Installation of Runtastic Bike App and activation code

Copy the link provided below into the address bar of your browser to open Runtastic.com; there you can get step-by-step help and instruc-tions for entering your activation code.

Runtastic.com/activate

Or scan the QR code below using your smartphone to open the page.

Page 8 of 16

In order to be able to use this fea-ture, you need to have previously downloaded the free app from the corresponding store, and then you can scan these types of codes. Now, scan the QR code and follow the instructions on Runtastic.com. In order to use your Runtastic Speed & Cadence Sensor you must activate your Bluetooth interface and the sensors in the Bike App. 2. Connecting the Speed & Ca-dence Sensor to your smartphone Open the Runtastic Bike App and access the Settings screen. Then choose „Speed & Cadence“. Select „Connect Speed & Cadence Sensor“. Activate „Enable BT Smart“. To acti-vate your Speed & Cadence Sensor take either the spoke or the pedal magnet and move it across the cor-

Page 9 of 16

responding marks on the Speed & Cadence Sensor, with a maximum distance of 4 – 5 mm between sen-sor and magnet.

Once successfully activated the color of the symbols for speed and cadence on the display of your smartphone will change from or-ange to green. If the activation has not been suc-cessful, choose “Unpair all sensors” and repeat the activation process. In addition, you can deactivate and then reactivate the Bluetooth signal in your phone settings. 3. Assembly of the Runtastic Speed & Cadence Sensor

1. We recommend attaching the Runtastic Speed & Ca-dence Sensor to the chain

Page 10 of 16

stay of your bike (see figure below).

2. Guide the cable ties through

the openings in your Runtastic Speed & Cadence Sensor. Mount the sensor to the chain stay so that the Runtastic logo faces out-ward. Close the cable ties, but do not tighten them firmly yet.

3. Position the spoke magnet on one of the spokes so that the magnet is level with the Runtastic Speed & Cadence Sensor. Mount the spoke magnet on the spoke and close the cable ties, but do not tighten them firmly yet.

Page 11 of 16

In order to be able to mount the pedal magnet in the correct po-sition, the pedal must first be disassembled. Then, position the pedal magnet so that it is level with the Runtastic Speed & Ca-dence Sensor.

Then mount the pedal onto the crank arm.

Adjust the position of the spoke magnet so the magnet passes very close to the sensor but does not touch it. Keep a maximum distance of 4 – 5 mm between the magnet and the Runtastic Speed & Cadence Sensor. Align

Page 12 of 16

the Runtastic Speed & Cadence Sensor towards the wheel / spokes as precisely as possible. Note: The Speed & Cadence Sensor is composed of two parts. To en-sure optimal assembly on your bicycle slightly loosen the screws with an Allen key. Now you can adjust the two parts for ideal positioning. When finished tighten the screws again.

NOTE: The speed and cadence measurement must only be activat-ed once, before the first training session, after deactivation of the Bluetooth interface, after clicking the “Unpair all sensors” button and/or upon replacement of the battery or the Runtastic Speed & Cadence Sensor.

Page 13 of 16

STORAGE

Do not expose the Runtastic Speed & Cadence Sensor to excessive solar radiation over a longer period. BATTERY REPLACEMENT IN THE Runtastic SPEED & CADENCE SEN-SOR Open the battery compartment cover with a coin by turning it counterclockwise.

Remove the old bat-tery and insert a new 3V battery (type CR2032). Always ensure that the positive pole (+) is facing up-wards. Refit the battery cover and lock it by turning it clockwise. Ensure that the cover is securely closed, to pre-vent moisture from entering the Runtastic Speed & Cadence Sensor. SPECIFICATIONS Runtastic Speed & Cadence Sensor

Power supply: 1 lithium battery (3 V 0.5 mA CR2032)

Page 14 of 16

Transmission frequency from Runtastic Speed & Cadence Sensor to smartphone: Bluetooth 4.0

Water tightness

The Runtastic Speed & Cadence Sensor is splash-proof.

DECLARATION OF CONFORMITY

R&TTE directive 1999/5/EC, EU di-rective 2011/65/EU (RoHS): Short text on declaration of con-formity: hereby, Krippl watches de-clares, that the Runtastic Speed & Cadence Sensor (Art. No.: RUNSCS1, Model: BSCBLE) are in compliance with the basic requirements, and the remaining relevant conditions of the guidelines 1999/5/EC and 2011/65/EU. You can find the complete text of the declaration of conformity on our homepage: hardware.runtastic.com

Page 15 of 16

Page 16 of 16

WARRANTY We offer a 24-month warranty for this product. The warranty period starts from the date of sale (receipt, proof of purchase). Within this peri-od we repair all defects resulting from material failure or malfunctions free of charge, except: batteries, improper handling, dropping, shock or the like. If you would like to submit a com-plaint, you have the following op-tions: a) Contact your dealer or b) Write an email to:

service@runtastic.com

PLEASE NOTE: FOR ORGANIZA-TIONAL REASONS, WE CANNOT AC-CEPT ANY UNANNOUNCED PACK-AGES WHICH HAVE NOT BEEN PRE-PAID.

Runtastic.com