Manual (Micro )EDM Mechanical Tool S Series’ F Series’Current (Amps) S 35 S 50 S 65 F 50 Plus F 65 Plus My EDMWork Tank (mm) 800×500 900×550 1150×660 1200×600 1500×800 2000×1000

×325 ×375 ×450 ×450 ×500 ×400Work Table (mm) 550×350 600×400 700×420 800×500 1000×600 1200×800X Travel (mm) 300 350 450 500 800 1200Y Travel (mm) 200 250 350 300 500 600Z Travel (mm) 200 250 200+200 250 250 400Max Job Wt (kgs) 300 500 600 2000 3500 4500Max Job HT (mm) 275 325 400 400 400 600Daylight-With

295 385 480 535 535 820Eletrode Holder (mm)Shut Height (mm) 95 135 80 285 285 420Throat Min (mm) N.A. N.A. N.A. 135 135 120Throat Max (mm) N.A. N.A. N.A. 440 540 720Pump Motor (HP) 0.5 0.5 0.5 0.5 0.5-2Nos. 0.5Die. Electric Tank (L) 170 240 525 635 900 1280Filtraction -Vertical 10μ-2 Nos 10μ-2 Nos 10μ-2 Nos 10μ-2 Nos 10μ-4 Nos 10μ-2 NosNet Weight (kgs) 1000 1250 1600 1600 2000 2800Machine Floor Area 1500× 2200× 2400× 2200× 2700× 3300×Micro (mm) 1500 1700 1600 1700 2600 3000Machine Floor Area 2200× 2300× 2400× 2200× 2700× 3300×ZNC (mm) 1500 1600 1600 1700 2600 3000

Manual (Micro )EDM

Machine Tool Unit Speed I Speed IIWork Table mm 400×300 (Stainless Steel) 550×350 (Stainless Steel)

X Travel mm 200 350 Y Travel mm 150 250Z Travel mm 300 300

Guide Travel Z2(Moto-rised) mm 150 150

Electrode Pipe Dia mm 0.3 ̴3.0 0.3 ̴3.0Max. Job Weight Kgs 300 350

Daylight 330 340Shut Height 180 190

Throat mm 310 380Max. Job Height mm 310 310

Max.Drilling Depth mm 300 300Dielectric Fluid Liters 50 50

Pulse GeneratorCurrent Amps 25 35Power KVA

Power Spply 415V,3 Phase ,50Hz 415V,3 Phase ,50HzOn Time Setting Frequency 10 Steps 10 StepsOff Time Setting Frequency 10 Steps 10 StepsPower Booster Gap C 10 Steps 10 Steps

Net Weight Kgs 800 900Machine Floor Area mm 1100×1700 1200×1900

EDM DRILL MACHINE

EDM DRILL MACHINE

Pulse Generator ZNCCurrent (Amps) 25 35 50 65 50 70 70Power Supply 415 V,3 Ph. 50 Hz 415 V,3 Ph. 50 HzDisplay system Hand Pendant with Digital Display 15’’ LED

Control systems Micro Processor based PC BASEPower (KVA) 3 4 5 7 5 7

MRR Gr-St*(mm3/min) 180 280 400 700 440 600MRR Cu-St*(mm3/min) 140 230 300 400 360 560

Best Surface finish (μ Ra) 0.5 0.7 0.7Min Electrode wear (%) 0.3 0.3 0.2

Pulse on time (micro sec) 1-2000/11 steps 2-2400Max Electrode Wt (kgs) 50 70

Floor Area 475×650 555×1000 600×650(for standalone) (mm)

ZNC EDM

PAC MACHINE TOOLS INDIA LLP FA-18, First Floor, Crown Plaza, Sector-15A, Mathura Road, Faridabad - 121007, Delhi (NCR) (India)

Tel.: +91-129-4001625 Fax: +91-129-4001627 E-mail : info@pacindia.net, Website: www.pacindia.net