LZB-1916R1A - EDACS SIMULCAST CONTROL POINT TRUNKING SHELF ... · EDACS SIMULCAST CONTROL POINT TRUNKING SHELF SXK 107 3847/2 TABLE OF CONTENTS ... This manual covers Ericsson and

ericssonz

Maintenance Manual

EDACS SIMULCASTCONTROL POINTTRUNKING SHELFSXK 107 3847/2

TABLE OF CONTENTS

Control Point Trunking Card ........................ AE/LZB 119 1886Vertical Turbo Card ...................................... AE/LZB 119 1887Vertical Interface Card.................................. AE/LZB 119 1888

AE/LZB 119 1916/1 R1A

2

NOTICE!

This manual covers Ericsson and General Electric products manufactured and sold by Ericsson Inc.

NOTICE!

Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Anyrepairs, alterations or substitution of recommended parts made by the user to this equipment not approved by themanufacturer could void the user's authority to operate the equipment in addition to the manufacturer's warranty.

NOTICE!

The software contained in this device is copyrighted by Ericsson Inc. Unpublished rights are reserved under the copyrightlaws of the United States.

This manual is published by Ericsson Inc., without any warranty. Improvements and changes to this manual necessitated bytypographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made byEricsson Inc., at any time and without notice. Such changes will be incorporated into new editions of this manual. No partof this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, includingphotocopying and recording, for any purpose, without the express written permission of Ericsson Inc.

EDACS and MASTR are registered trademarks, and GETC, Failsoft, Aegis, and Guardog are trademarks of Ericsson Inc.

Copyright November 1996, Ericsson, Inc.

AE/LZB 119 1916/1 R1A

3

TABLE OF CONTENTS

Section/Paragraph Page

TABLE OF CONTENTS..................................................................................................................................... 3

LIST OF FIGURES AND TABLES ................................................................................................................... 3

SPECIFICATIONS*............................................................................................................................................ 5

INTRODUCTION................................................................................................................................................ 5

DESCRIPTION.................................................................................................................................................... 5TRUNKING SHELF ...................................................................................................................................... 5MODULES ..................................................................................................................................................... 6

CONNECTION LIST .......................................................................................................................................... 8

PARTS LIST ........................................................................................................................................................ 24CONTROL POINT TRUNKING SHELF - SXK 107 3847/2........................................................................ 24BACKPLANE ASSEMBLY - ROA 117 2256............................................................................................... 24

ASSEMBLY DIAGRAM..................................................................................................................................... 25CONTROL POINT TRUNKING SHELF VME CAGE - SXK 107 3847/2 .................................................. 25CARD CAGE ASSEMBLY - SXA 120 4329/2 ............................................................................................. 26

OUTLINE DIAGRAM ........................................................................................................................................ 27

SCHEMATIC DIAGRAM .................................................................................................................................. 29

CONTROL POINT TRUNKING SHELF CONFIGURATION...................................................................... 37

LIST OF FIGURES AND TABLES

Figure Title Page

Figure 1 - Interconnect Diagram per Channel ............................................................................................................7

Table 1 - Connector P1 Pinouts .................................................................................................................................6

Table 2 - Connector J01, Site Controller Interface ....................................................................................................8

Table 3 - Connector J02, Continous Reset .................................................................................................................9

Table 4 - Connector J03, Remote (Voted) Data.........................................................................................................9

Table 5 - Connector J04, Voted Digital Interconnect...............................................................................................10

Table 6 - Connector J05, 9600 bps TX Data to CV2 Selector..................................................................................10

Table 7 - Connector J06, Inhibit Signal From Alarm Computer ..............................................................................11

Table 8 - Connector J07, Console Key From MSC..................................................................................................11

Table 9 - Connector J08, PTT Switch Contacts .......................................................................................................12

Table 10 - Connector J09, Analog/Digital Switch Contacts.....................................................................................13

Table 11 - Connector J10, 9600 bps Data................................................................................................................14

Table 12 - Connector J11, 9000 Hz Clock...............................................................................................................14

AE/LZB 119 1916/1 R1A LIST OF FIGURES AND TABLES

4

TABLE OF CONTENTS

Section/Paragraph Page

Table 13 - Connector J12, 150 bps Low Speed Data (LSD) ....................................................................................15

Table 14 - Connector J13, GPS Combined Reference Signal ..................................................................................15

Table 15 - Connector J14, Request To Send (RTS) Signal ......................................................................................16

Table 16 - Connector J15, Clear To Send (RTS) Signal ..........................................................................................16

Table 17 - Connector J18/J19, Backup Serial Link (BSL) and Frame Sync Line (FSL) Signal..............................17

Table 18 - Connector J20/J21, Reset Signals ...........................................................................................................17

Table 19 - Connector J22, Transmit Clock (TXC) Signal........................................................................................18

Table 20 - Connector P01, Input Power ...................................................................................................................18

Table 21 - Connector PS01*, Turbo Card Slot.........................................................................................................19

Table 22 - Connector PS02*, Control Point Trunking Card Slot .............................................................................20

Table 23 - Connector PS03*, Simulcast Interface Card Slot....................................................................................22

AE/LZB 119 1916/1 R1A

5

SPECIFICATIONS*

DIMENSIONS (H x W x D) 13.3cm x 48.26cm x 24.03cm (5.22" x 19.00" x 9.5")(3 Rack Units x 220 mm Card Cage)

INPUT VOLTAGE +5 Vdc, +12 Vdc, -12 Vdc

NUMBER OF CARD SLOTS 21

CONNECTORS:

J1

J2 thru J17, and J22

J18, J19, J20, and J21

P1

PS1 thru PS18

24 Pin Header

14 Pin Header

6 Pin Modular

15 Pin Power Connector

96 Pin DIN Connector

INTRODUCTIONThis manual provides maintenance information for the

EDACS Simulcast Control Point Trunking Card Shelf.

DESCRIPTION

TRUNKING SHELF

The Trunking Card Shelf is a 3 Rack Unit VME cardcage consisting of the Card Cage SXA 120 4329/2 andBackplane ROA 117 2256.

Each shelf provides up to twenty-one (21) card slots.However, only 18 slots are used by the Control Point forhousing combinations of the Vertical Turbo Card, ControlPoint Trunking Card and Simulcast Interface Card. A set ofthese cards is required for each channel.

Each plug-in card measures 100mm high by 220mmlong with a 96 pin DIN connector for the card to backplaneinterface. The number of shelves and card sets depends onthe number of channels.

Each channel connected to the shelf interfaces with theTrunking Card through the Interface Card. Each TrunkingCard also interfaces to its own Turbo Card for additionalmemory.

The Backplane, ROA 117 2256 is a six layered printedcircuit board. Each backplane contains eighteen (18) 96 pinDIN connectors to mate with the cards installed in the cardcage. The rear of the backplane has the input and outputconnectors, power connectors, and the input power fuses.Refer to the Outline Diagrams for location of the variouscomponents, and the schematic diagrams for pin and signalrouting information.

Outline Diagram (1078-ROA 117 2256 sheet 1) showsthe front side of the board as seen through the front or openside of the card cage. The diagram shows the location ofconnectors PS01 thru PS18.

Sheet 2 of the Outline Diagram shows the back side ofthe board as seen from the rear or closed side of the cardcage. This diagram shows the location of all input andoutput connectors, the input power connector and the threepower fuses.

* These specifications are intended for use during servicing. Refer to appropriate Specification Sheet for thecomplete specification.

AE/LZB 119 1916/1 R1A DESCRIPTION

6

Power is supplied to the shelf's power connector P1from the Power Distribution Panel. The +5 Vdc, +12 Vdc,and -12 Vdc power is then routed through fuses F1, F2 andF3 respectively to the individual plug-in cards via thebackplane. Pinouts for P1 are as follows:

Table 1 - Connector P1 Pinouts

P1-1 GND P1-6 +12 Vdc P1-11 +5 Vdc

P1-2 GND P1-7 GND P1-12 -12 Vdc

P1-3 GND P1-8 +5 Vdc P1-13 +5 Vdc

P1-4 GND P1-9 +12 Vdc P1-14 +5 Vdc

P1-5 GND P1-10 +5 Vdc P1-15 -12 Vdc

MODULES

The modules (cards) used in the Control Point TrunkingShelf includes the following:

• Control Point Trunking Card ROA 117 2240/3.Refer to AE/LZB 119 1886.

• Vertical Turbo Card ROA 117 2239. Refer toAE/LZB 119 1887.

• Vertical Interface Card ROA 117 2235. Refer toAE/LZB 119 1888.

DESCRIPTION AE/LZB 119 1916/1 R1A

7

U3

RA

M D

00-D

08

A2

A9

A2

A9

U3

RA

M A

00-A

15

B1

B16

RU

S I

N

AD

OU

T

CT

S

RX

D

RT

S

9.6

CLK

150

DA

TA

(LS

D)

MC

LK

PT

T O

UT

VD

I T

TL

A16

A16

A26

A26

C3

C3

C4

C4

C5

C5

C8

C8

C9

C9

C10

C10

C14

C14

C24

C24

WR

ITE

RA

M C

S

A10

A10

A11

A11

TU

RB

OR

OA

117

223

9C

PT

CR

OA

117

224

0/3

INT

ER

FA

CE

RO

A 1

17 2

235

AD

OU

T+

B3

AD

OU

T-

B4

J9T

o P

O1-

J9(T

o C

trl

Pan

el C

900)

CT

S23

2+B

7C

TS

232-

B8

J15

RT

S23

2+B

5R

TS

232-

B6

J14

Rem

ote

RX

D+

B9

Rem

ote

RX

D-

B10

J3T

o P

01-J

9(V

oted

Dat

a)

GC

LK O

UT

+B

15G

CLK

OU

T-

B16

J11

To

D60

7-J2

(9.6

Clo

ck)

9.6R

EF

IN

+B

179.

6RE

F I

N-

B18

J13

To

D80

0-J1

1,J1

2, J

13,

or J

14(9

600

Ref

eren

ce)

150

D O

UT

+B

1115

0 D

OU

T-

B12

J12

To

D80

0-J1

, J2

,J3

, or

J4

(150

bps

Dat

a)

PT

T O

UT

+B

1P

TT

OU

T-

B2

J8T

o P

01-J

8(T

o C

trl P

anel

C90

0)

VD

I IN

+C

25V

DI

IN-

C26

J4T

o P

01-J

4(V

oted

Dig

ital

Inte

rcon

nect

)

GD

AT

OU

T+

B13

GD

AT

OU

T-

B14

J10

To

D60

7-J1

(9.6

Dat

a to

D80

0-J1

8)9.

6 D

AT

AA

29C

11

SIM

ULC

AS

T C

ON

TR

OL

PO

INT

TR

UN

KIN

G C

AR

D S

HE

LF (

SX

K 1

07 3

847/

2)D

501,

D50

2, D

503,

D50

4

TX

DC

6J5

To

P01

-J5

(RS

-232

Dat

a to

CV

2 S

elec

tor)

MS

C K

eyC

17J7

To

P01

-J7

(MS

C K

ey t

o V

oter

)

INH

IBIT

C12

J6T

o B

403-

J19

(Sig

nal

to A

larm

Com

pute

r -

D80

5)

C23

MO

M R

ES

ET

J20

J21

B40

3-J5

2(M

omen

tary

Res

etfr

om S

/C G

uard

og)

C20

J1P

01-J

1 or

J2

(To

Site

Con

trol

ler)

SIT

E C

NT

L R

X1

SIT

E C

NT

L T

X1

C19C7

TX

CJ2

2

C29

J18

J19

Dai

sy C

hain

ed t

o :

Syn

c S

helf

D80

0-J6

and

Dow

nlin

k

BS

L

FS

LC

28B1

B16

Figure 1 - Interconnect Diagram per Channel

AE/LZB 119 1916/1 R1A CONNECTION LIST

8

Table 2 - Connector J01, Site Controller Interface

CONNECTORPIN

SIGNAL NAME INPUT/OUTPUT

ANALOG/DIGITAL

LEVEL

1 G01_SITE_CNTL_RX1 Input Digital 19.2k RX Data2 GND 0 V3 G01_SITE_CNTL_TX1 Output Digital 19.2k TX Data4 GND 0 V5 G02_SITE_CNTL_RX1 Input Digital 19.2k RX Data6 GND 0 V7 G02_SITE_CNTL_TX1 Output Digital 19.2k TX Data8 GND 0 V9 G03_SITE_CNTL_RX1 Input Digital 19.2k RX Data10 GND 0 V11 G03_SITE_CNTL_TX1 Output Digital 19.2k TX Data12 GND 0 V13 G04_SITE_CNTL_RX1 Input Digital 19.2k RX Data14 GND 0 V15 G04_SITE_CNTL_TX1 Output Digital 19.2k TX Data16 GND 0 V17 G05_SITE_CNTL_RX1 Input Digital 19.2k RX Data18 GND 0 V19 G05_SITE_CNTL_TX1 Output Digital 19.2k TX Data20 GND 0 V21 G06_SITE_CNTL_RX1 Input Digital 19.2k RX Data22 GND 0 V23 G06_SITE_CNTL_TX1 Output Digital 19.2k TX Data24 GND 0 V

CONNECTION LIST AE/LZB 119 1916/1 R1A

9

Table 3 - Connector J02, Continous Reset

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J02 - 1 GND 0 VJ02 - 2 G01_CONT_RESET Input Digital Active low resets GPTCJ02 - 3 GND 0 VJ02 - 4 G02_CONT_RESET Input Digital Active low resets GPTCJ02 - 5 GND 0 VJ02 - 6 G03_CONT_RESET Input Digital Active low resets GPTCJ02 - 7 GND 0 VJ02 - 8 G04_CONT_RESET Input Digital Active low resets GPTCJ02 - 9 GND 0 VJ02 - 10 G05_CONT_RESET Input Digital Active low resets GPTCJ02 - 11 GND 0 VJ02 - 12 G06_CONT_RESET Input Digital Active low resets GPTCJ02 - 13 N/CJ02 - 14 N/C

Table 4 - Connector J03, Remote (Voted) Data

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J03 - 1 G01_Remote_RXD- Input Digital 9600 bps DataJ03 - 2 G01_ Remote_RXD+ Input Digital 9600 bps DataJ03 - 3 G02_Remote_RXD- Input Digital 9600 bps DataJ03 - 4 G02_ Remote_RXD+ Input Digital 9600 bps DataJ03 - 5 G03_Remote_RXD- Input Digital 9600 bps DataJ03 - 6 G03_ Remote_RXD+ Input Digital 9600 bps DataJ03 - 7 G04_Remote_RXD- Input Digital 9600 bps DataJ03 - 8 G04_ Remote_RXD+ Input Digital 9600 bps DataJ03 - 9 G05_Remote_RXD- Input Digital 9600 bps DataJ03 - 10 G05_ Remote_RXD+ Input Digital 9600 bps DataJ03 - 11 G06_Remote_RXD- Input Digital 9600 bps DataJ03 - 12 G06_ Remote_RXD+ Input Digital 9600 bps DataJ03 - 13 N/CJ03 - 14 N/C


10

Table 5 - Connector J04, Voted Digital Interconnect

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J04 - 1 G01_VDI_IN- Input Digital RS-232 DataJ04 - 2 G01_ VDI_IN+ Input Digital RS-232 DataJ04 - 3 G02_VDI_IN- Input Digital RS-232 DataJ04 - 4 G02_ VDI_IN+ Input Digital RS-232 DataJ04 - 5 G03_VDI_IN- Input Digital RS-232 DataJ04 - 6 G03_ VDI_IN+ Input Digital RS-232 DataJ04 - 7 G04_VDI_IN- Input Digital RS-232 DataJ04 - 8 G04_ VDI_IN+ Input Digital RS-232 DataJ04 - 9 G05_VDI_IN- Input Digital RS-232 DataJ04 - 10 G05_ VDI_IN+ Input Digital RS-232 DataJ04 - 11 G06_VDI_IN- Input Digital RS-232 DataJ04 - 12 G06_ VDI_IN+ Input Digital RS-232 DataJ04 - 13 N/CJ04 - 14 N/C

Table 6 - Connector J05, 9600 bps TX Data to CV2 Selector

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J05 - 1 GNDJ05 - 2 G01_TXD Output Digital RS-232 Data to CV2 SelectorJ05 - 3 GNDJ05 - 4 G02_TXD Output Digital RS-232 Data to CV2 SelectorJ05 - 5 GNDJ05 - 6 G03_TXD Output Digital RS-232 Data to CV2 SelectorJ05 - 7 GNDJ05 - 8 G04_TXD Output Digital RS-232 Data to CV2 SelectorJ05 - 9 GNDJ05 - 10 G05_TXD Output Digital RS-232 Data to CV2 SelectorJ05 - 11 GNDJ05 - 12 G06_TXD Output Digital RS-232 Data to CV2 SelectorJ05 - 13 N/CJ05 - 14 N/C


11

Table 7 - Connector J06, Inhibit Signal From Alarm Computer

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J06 - 1 GNDJ06 - 2 G01_INHIBIT Input Digital Active lowJ06 - 3 GNDJ06 - 4 G02_INHIBIT Input Digital Active lowJ06 - 5 GNDJ06 - 6 G03_INHIBIT Input Digital Active lowJ06 - 7 GNDJ06 - 8 G04_INHIBIT Input Digital Active lowJ06 - 9 GNDJ06 - 10 G05_INHIBIT Input Digital Active lowJ06 - 11 GNDJ06 - 12 G06_INHIBIT Input Digital Active lowJ06 - 13 N/CJ06 - 14 N/C

Table 8 - Connector J07, Console Key From MSC

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J07 - 1 GND 0 VdcJ07 - 2 G01_MSC_KEY Input Digital TTLJ07 - 3 GND 0 VdcJ07 - 4 G02_MSC_KEY Input Digital TTLJ07 - 5 GND 0 VdcJ07 - 6 G03_MSC_KEY Input Digital TTLJ07 - 7 GND 0 VdcJ07 - 8 G04_MSC_KEY Input Digital TTLJ07 - 9 GND 0 VdcJ07 - 10 G05_MSC_KEY Input Digital TTLJ07 - 11 GND 0 VdcJ07 - 12 G06_MSC_KEY Input Digital TTLJ07 - 13 N/CJ07 - 14 N/C


12

Table 9 - Connector J08, PTT Switch Contacts

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J08 - 1 G01_PTT_OUT- Output Digital 0 VdcJ08 - 2 G01_PTT_OUT+ Output Digital Relay Contact Closure, ±0.5 Vdc

when closedJ08 - 3 G02_PTT_OUT- Output Digital 0 VdcJ08 - 4 G02_PTT_OUT+ Output Digital Relay Contact Closure, ±0.5 Vdc





when closedJ08 - 13 N/CJ08 - 14 N/C


13

Table 10 - Connector J09, Analog/Digital Switch Contacts

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J09 - 1 G01_AD_OUT- Output Digital 0 VdcJ09 - 2 G01_AD_OUT+ Output Digital Relay Contact Closure, ±0.5

Vdc when closedJ09 - 3 G02_AD_OUT- Output Digital 0 VdcJ09 - 4 G02_AD_OUT+ Output Digital Relay Contact Closure, ±0.5





Vdc when closedJ09 - 13 N/CJ09 - 14 N/C


14

Table 11 - Connector J10, 9600 bps Data

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J10 - 1 G01_GDAT_OUT- Output Digital 0 VdcJ10 - 2 G01_GDAT_OUT+ Output Digital 9600 bps, RS-232 dataJ10 - 3 G02_GDAT_OUT- Output Digital 0 VdcJ10 - 4 G02_GDAT_OUT+ Output Digital 9600 bps, RS-232 dataJ10 - 5 G03_GDAT_OUT- Output Digital 0 VdcJ10 - 6 G03_GDAT_OUT+ Output Digital 9600 bps, RS-232 dataJ10 - 7 G04_GDAT_OUT- Output Digital 0 VdcJ10 - 8 G04_GDAT_OUT+ Output Digital 9600 bps, RS-232 dataJ10 - 9 G05_GDAT_OUT- Output Digital 0 VdcJ10 - 10 G05_GDAT_OUT+ Output Digital 9600 bps, RS-232 dataJ10 - 11 G06_GDAT_OUT- Output Digital 0 VdcJ10 - 12 G06_GDAT_OUT+ Output Digital 9600 bps, RS-232 dataJ10 - 13 N/CJ10 - 14 N/C

Table 12 - Connector J11, 9000 Hz Clock

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J11 - 1 G01_GCLK_OUT- Output Digital 0 VdcJ11 - 2 G01_GCLK_OUT+ Output Digital 9600Hz, RS-232 dataJ11 - 3 G02_GCLK_OUT- Output Digital 0 VdcJ11 - 4 G02_GCLK_OUT+ Output Digital 9600Hz, RS-232 dataJ11 - 5 G03_GCLK_OUT- Output Digital 0 VdcJ11 - 6 G03_GCLK_OUT+ Output Digital 9600Hz, RS-232 dataJ11 - 7 G04_GCLK_OUT- Output Digital 0 VdcJ11 - 8 G04_GCLK_OUT+ Output Digital 9600Hz, RS-232 dataJ11 - 9 G05_GCLK_OUT- Output Digital 0 VdcJ11 - 10 G05_GCLK_OUT+ Output Digital 9600Hz, RS-232 dataJ11 - 11 G06_GCLK_OUT- Output Digital 0 VdcJ11 - 12 G06_GCLK_OUT+ Output Digital 9600Hz, RS-232 dataJ11 - 13 N/CJ11 - 14 N/C


15

Table 13 - Connector J12, 150 bps Low Speed Data (LSD)

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J12 - 1 G01_150_D_OUT- Output Digital 0 VdcJ12 - 2 G01_150_D_OUT+ Output Digital 150 bps LSD (RS-232)J12 - 3 G02_150_D_OUT- Output Digital 0 VdcJ12 - 4 G02_150_D_OUT+ Output Digital 150 bps LSD (RS-232)J12 - 5 G03_150_D_OUT- Output Digital 0 VdcJ12 - 6 G03_150_D_OUT+ Output Digital 150 bps LSD (RS-232)J12 - 7 G04_150_D_OUT- Output Digital 0 VdcJ12 - 8 G04_150_D_OUT+ Output Digital 150 bps LSD (RS-232)J12 - 9 G05_150_D_OUT- Output Digital 0 VdcJ12 - 10 G05_150_D_OUT+ Output Digital 150 bps LSD (RS-232)J12 - 11 G06_150_D_OUT- Output Digital 0 VdcJ12 - 12 G06_150_D_OUT+ Output Digital 150 bps LSD (RS-232)J12 - 13 N/CJ12 - 14 N/C

Table 14 - Connector J13, GPS Combined Reference Signal

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J13 - 1 G01_9.6_REF_IN- Input Digital 9600 Hz (RS-422) CR1 DataJ13 - 2 G01_9.6_REF_IN+ Input Digital 9600 Hz (RS-422) CR2 DataJ13 - 3 G02_9.6_REF_IN- Input Digital 9600 Hz (RS-422) CR1 DataJ13 - 4 G02_9.6_REF_IN+ Input Digital 9600 Hz (RS-422) CR2 DataJ13 - 5 G03_9.6_REF_IN- Input Digital 9600 Hz (RS-422) CR1 DataJ13 - 6 G03_9.6_REF_IN+ Input Digital 9600 Hz (RS-422) CR2 DataJ13 - 7 G04_9.6_REF_IN- Input Digital 9600 Hz (RS-422) CR1 DataJ13 - 8 G04_9.6_REF_IN+ Input Digital 9600 Hz (RS-422) CR2 DataJ13 - 9 G05_9.6_REF_IN- Input Digital 9600 Hz (RS-422) CR1 DataJ13 - 10 G05_9.6_REF_IN+ Input Digital 9600 Hz (RS-422) CR2 DataJ13 - 11 G06_9.6_REF_IN- Input Digital 9600 Hz (RS-422) CR1 DataJ13 - 12 G06_9.6_REF_IN+ Input Digital 9600 Hz (RS-422) CR2 DataJ13 - 13 N/CJ13 - 14 N/C


16

Table 15 - Connector J14, Request To Send (RTS) Signal

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J14 - 1 G01_RTS_232- Output Digital 0 VdcJ14 - 2 G01_RTS_232+ Output Digital RTS Data Stream (RS-232)J14 - 3 G02_RTS_232- Output Digital 0 VdcJ14 - 4 G02_RTS_232+ Output Digital RTS Data Stream (RS-232)J14 - 5 G03_RTS_232- Output Digital 0 VdcJ14 - 6 G03_RTS_232+ Output Digital RTS Data Stream (RS-232)J14 - 7 G04_RTS_232- Output Digital 0 VdcJ14 - 8 G04_RTS_232+ Output Digital RTS Data Stream (RS-232)J14 - 9 G05_RTS_232- Output Digital 0 VdcJ14 - 10 G05_RTS_232+ Output Digital RTS Data Stream (RS-232)J14 - 11 G06_RTS_232- Output Digital 0 VdcJ14 - 12 G06_RTS_232+ Output Digital RTS Data Stream (RS-232)J14 - 13 N/CJ14 - 14 N/C

Table 16 - Connector J15, Clear To Send (RTS) Signal

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J15 - 1 G01_CTS_232- Input Digital 0 VdcJ15 - 2 G01_CTS_232+ Input Digital CTS Data Stream (RS-232)J15 - 3 G02_CTS_232- Input Digital 0 VdcJ15 - 4 G02_CTS_232+ Input Digital CTS Data Stream (RS-232)J15 - 5 G03_CTS_232- Input Digital 0 VdcJ15 - 6 G03_CTS_232+ Input Digital CTS Data Stream (RS-232)J15 - 7 G04_CTS_232- Input Digital 0 VdcJ15 - 8 G04_CTS_232+ Input Digital CTS Data Stream (RS-232)J15 - 9 G05_CTS_232- Input Digital 0 VdcJ15 - 10 G05_CTS_232+ Input Digital CTS Data Stream (RS-232)J15 - 11 G06_CTS_232- Input Digital 0 VdcJ15 - 12 G06_CTS_232+ Input Digital CTS Data Stream (RS-232)J15 - 13 N/CJ15 - 14 N/C


17

Table 17 - Connector J18/J19, Backup Serial Link (BSL) and Frame Sync Line (FSL) Signal

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J18/J19 - 1 J18/J19 - 2 BSL I/O Digital Backup Serial Link, 19.2k Baud

data on 13 Vdc level.J18/J19 - 3 GND 0 VdcJ18/J19 - 4 FSL I/O Digital Frame Sync Line, Periodic

negative pulses on 0-13 Vdc level.J18/J19 - 5 GND 0 VdcJ18/J19 - 6

Table 18 - Connector J20/J21, Reset Signals

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J20/J21 - 1 J20/J21 - 2 MOM_RESET Input Digital Active Low (Momentary by way of

internal one-shot.)J20/J21 - 3 GND 0 VdcJ20/J21 - 4 GUARDOG_STATUS Input Digital not usedJ20/J21 - 5 GND 0 VdcJ20/J21 - 6


18

Table 19 - Connector J22, Transmit Clock (TXC) Signal

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

J22 - 1 GND Output Digital 0 VdcJ22 - 2 G01_TXC Output Digital 9600 baud square wareJ22 - 3 GND Output Digital 0 VdcJ22 - 4 G02_TXC Output Digital 9600 baud square wareJ22 - 5 GND Output Digital 0 VdcJ22 - 6 G03_TXC Output Digital 9600 baud square wareJ22 - 7 GND Output Digital 0 VdcJ22 - 8 G04_TXC Output Digital 9600 baud square wareJ22 - 9 GND Output Digital 0 VdcJ22 - 10 G05_TXC Output Digital 9600 baud square wareJ22 - 11 GND Output Digital 0 VdcJ22 - 12 G06_TXC Output Digital 9600 baud square wareJ22 - 13 N/CJ22 - 14 N/C

Table 20 - Connector P01, Input Power

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

P01 - 1 GND Input Analog 0 Vdc





P01 - 6 +12_IN Input Analog +12 Vdc






P01 - 12 -12_IN Input Analog -12 Vdc



P01 - 15 -12_IN Input Analog -12 Vdc


19

For Turbo Cards in slots 4, 7, 10, 13, and 16 replace the connector number with PS04, PS07, PS10, PS13, and PS16respectively. In addition, reference to Signal Names starting with G01 are replaced with G02, G03, G04, G05, and G06respectively.

Table 21 - Connector PS01*, Turbo Card Slot

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

PS01 - A1 GND 0 VdcPS01 - A2 G01_U3_RAM_D00 I/O Digital Data Bus to CPTCPS01 - A3 G01_U3_RAM_D01 I/O Digital Data Bus to CPTCPS01 - A4 G01_U3_RAM_D02 I/O Digital Data Bus to CPTCPS01 - A5 G01_U3_RAM_D03 I/O Digital Data Bus to CPTCPS01 - A6 G01_U3_RAM_D04 I/O Digital Data Bus to CPTCPS01 - A7 G01_U3_RAM_D05 I/O Digital Data Bus to CPTCPS01 - A8 G01_U3_RAM_D06 I/O Digital Data Bus to CPTCPS01 - A9 G01_U3_RAM_D07 I/O Digital Data Bus to CPTCPS01 - A10 G01_WRITE Input Digital Write Enable pulse from CPTCPS01 - A11 G01_RAM_CS Input Digital Output Enable pulse from CPTCPS01 - A30 +5 Input +5 VdcPS01 - A31 +5 Input +5 VdcPS01 - A32 GND 0 VdcPS01 - B1 G01_U3_RAM_A00 I/O Digital Address Bus to CPTCPS01 - B2 G01_U3_RAM_A01 I/O Digital Address Bus to CPTCPS01 - B3 G01_U3_RAM_A02 I/O Digital Address Bus to CPTCPS01 - B4 G01_U3_RAM_A03 I/O Digital Address Bus to CPTCPS01 - B5 G01_U3_RAM_A04 I/O Digital Address Bus to CPTCPS01 - B6 G01_U3_RAM_A05 I/O Digital Address Bus to CPTCPS01 - B7 G01_U3_RAM_A06 I/O Digital Address Bus to CPTCPS01 - B8 G01_U3_RAM_A07 I/O Digital Address Bus to CPTCPS01 - B9 G01_U3_RAM_A08 I/O Digital Address Bus to CPTCPS01 - B10 G01_U3_RAM_A09 I/O Digital Address Bus to CPTCPS01 - B11 G01_U3_RAM_A10 I/O Digital Address Bus to CPTCPS01 - B12 G01_U3_RAM_A11 I/O Digital Address Bus to CPTCPS01 - B13 G01_U3_RAM_A12 I/O Digital Address Bus to CPTCPS01 - B16 G01_U3_RAM_A15 Output Digital Address Bus to CPTCPS01 - B24 G01_TX1_232 Output Digital RS-232 Programming DataPS01 - B25 G01_RX1_232 Input Digital RS-232 Programming DataPS01 - B26 G01_TX2_232 Output Digital RS-232 Programming DataPS01 - B27 G01_RX2_232 Input Digital RS-232 Programming DataPS01 - B30 +5 Input +5 VdcPS01 - B31 +5 Input +5 VdcPS01 - B32 GND 0 VdcPS01 - C1 GND 0 VdcPS01 - C30 -12 Input -12 VdcPS01 - C31 +12 Input +12 VdcPS01 - C32 GND 0 Vdc


20

Table 22 - Connector PS02*, Control Point Trunking Card Slot

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

PS02 - A1 GND 0 VdcPS02 - A2 G01_U3_RAM_D00 I/O Digital Data Bus to TurboPS02 - A3 G01_U3_RAM_D01 I/O Digital Data Bus to TurboPS02 - A4 G01_U3_RAM_D02 I/O Digital Data Bus to TurboPS02 - A5 G01_U3_RAM_D03 I/O Digital Data Bus to TurboPS02 - A6 G01_U3_RAM_D04 I/O Digital Data Bus to TurboPS02 - A7 G01_U3_RAM_D05 I/O Digital Data Bus to TurboPS02 - A8 G01_U3_RAM_D06 I/O Digital Data Bus to TurboPS02 - A9 G01_U3_RAM_D07 I/O Digital Data Bus to TurboPS02 - A10 G01_WRITE Output Digital TTL Write Enable pulse to TurboPS02 - A11 G01_RAM_CS Output Digital TTL Output Enable pulse to TurboPS02 - A16 G01_AD_OUT Output Digital TTLPS02 - A26 G01_RUS_IN 0 Vdc (grounded in Interface Card)PS02 - A28 GUARDOG_STATUS Not UsedPS02 - A29 G01_9.6_D Input Digital 9600 bps Data (TTL)PS02 - A30 +5 Input +5 VdcPS02 - A31 +5 Input +5 VdcPS02 - A32 GND 0 VdcPS02 - B1 G01_U3_RAM_A00 I/O Digital Address Bus to TurboPS02 - B2 G01_U3_RAM_A01 I/O Digital Address Bus to TurboPS02 - B3 G01_U3_RAM_A02 I/O Digital Address Bus to TurboPS02 - B4 G01_U3_RAM_A03 I/O Digital Address Bus to TurboPS02 - B5 G01_U3_RAM_A04 I/O Digital Address Bus to TurboPS02 - B6 G01_U3_RAM_A05 I/O Digital Address Bus to TurboPS02 - B7 G01_U3_RAM_A06 I/O Digital Address Bus to TurboPS02 - B8 G01_U3_RAM_A07 I/O Digital Address Bus to TurboPS02 - B9 G01_U3_RAM_A08 I/O Digital Address Bus to TurboPS02 - B10 G01_U3_RAM_A09 I/O Digital Address Bus to TurboPS02 - B11 G01_U3_RAM_A10 I/O Digital Address Bus to TurboPS02 - B12 G01_U3_RAM_A11 I/O Digital Address Bus to TurboPS02 - B13 G01_U3_RAM_A12 I/O Digital Address Bus to TurboPS02 - B16 G01_U3_RAM_A15 Output Digital Address Bus to TurboPS02 - B30 +5 Input +5 VdcPS02 - B31 +5 Input +5 VdcPS02 - B32 GND 0 VdcPS02 - C1 GND 0 VdcPS02 - C3 G01_CTS Input Digital TTLPS02 - C4 G01_RTS Output Digital TTLPS02 - C5 G01_RXD Input Digital TTLPS02 - C6 G01_TXD Output Digital RS-232 DataPS02 - C7 G01_TXC Output Digital RS-232 DataPS02 - C8 G01_9.6_CLK Output Digital TTL 9600 HzPS02 - C9 G01_MCLK Input Digital TTL 11.0592 MHzPS02 - C10 G01_150_D Output Digital TTL 150 bpsPS02 - C12 G01_INHIBIT Input Digital TTL, Active Low


21

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

PS02 - C14 G01_PTT_OUT Output Digital TTLPS02 - C17 G01_MSC_KEY Input Digital TTLPS02 - C19 G01_SITE_CNTL_RX1 Input Digital 19.2k Baud RX DataPS02 - C20 G01_SITE_CNTL_TX1 Output Digital 19.2k Baud TX DataPS02 - C22 G01_CONT_RESET I/O Digital TTL, Active Low Resets CPTCPS02 - C23 MOM-RESET Input Digital TTL, momentary active low resets

CPTCPS02 - C24 G01_VDI_TTL Input Digital TTLPS02 - C28 BSL I/O Digital 19.2k Baud on 13 Vdc levelPS02 - C29 FSL Input Digital Periodic negative pulses on 0 to 13

Vdc levelPS02 - C30 -12 Input -12 VdcPS02 - C31 +12 Input +12 VdcPS02 - C32 GND 0 Vdc

For Control Point Trunking Cards in slots 5, 8, 11, 14, and 17 replace the connector number with PS05, PS08, PS11, PS14,and PS17 respectively. In addition, reference to Signal Names starting with G01 are replaced with G02, G03, G04, G05, andG06 respectively.


22

Table 23 - Connector PS03*, Simulcast Interface Card Slot

CONNECTORPIN


ANALOG/DIGITAL

LEVEL

PS03 - A1 GND 0 VdcPS03 - A16 G01_AD_OUT Input Digital TTLPS03 - A26 G01_RUS_IN 0 Vdc (grounded in Interface Card)PS03 - A30 +5 Input +5 VdcPS03 - A31 +5 Input +5 VdcPS03 - A32 GND 0 VdcPS03 - B1 G01_PTT_OUT+ Output Solid State Switch, ±0.5 Vdc when

closedPS03 - B2 G01_PTT_OUT- Output 0 VdcPS03 - B3 G01_AD_OUT+ Output Solid State Switch, ±0.5 Vdc when

closedPS03 - B4 G01_AD_OUT- Output 0 VdcPS03 - B5 G01_RTS_232+ Output RTS Data Stream (RS-232)PS03 - B6 G01_RTS_232- Output 0 VdcPS03 - B7 G01_CTS_232+ Output CTS Data Stream (RS-232)PS03 - B8 G01_CTS_232- Output 0 VdcPS03 - B9 G01_REMOTE_RXD+ Output TTLPS03 - B10 G01_REMOTE_RXD- Output 0 VdcPS03 - B11 G01_150_D_OUT+ Output 150 bps, RS-232PS03 - B12 G01_150_D_OUT- Output 0 VdcPS03 - B13 G01_GDAT_OUT+ Output 9600 bps, RS-232PS03 - B14 G01_GDAT_OUT- Output 0 VdcPS03 - B15 G01_GCLK_OUT+ Output 9600 bps, RS-232PS03 - B16 G01_GCLK_OUT- Output 0 VdcPS03 - B17 G01_9.6_REF_IN+ Input 9600 Hz, RS-422PS03 - B18 G01_9.6_REF_IN- Input 9600 Hz, RS-422PS03 - B30 +5 Input +5 VdcPS03 - B31 +5 Input +5 VdcPS03 - B32 GND 0 VdcPS03 - C1 GND 0 VdcPS03 - C3 G01_CTS Output Digital TTLPS03 - C4 G01_RTS Input Digital TTLPS03 - C5 G01_RXD Input Digital TTLPS03 - C8 G01_9.6_CLK Input Digital TTL 9600 HzPS03 - C9 G01_MCLK Output Digital TTL 11.0592 MHzPS03 - C10 G01_150_D Input Digital TTL 150 bpsPS03 - C11 G01_9.6_D Input Digital TTL, 9600 bpsPS03 - C14 G01_PTT_OUT Input Digital TTLPS03 - C24 G01_VDI_TTL Output Digital TTLPS03 - C25 G01_VDI_IN+ Input Digital RS-232PS03 - C26 G01_VDI_IN- Input Digital 0 VdcPS03 - C30 -12 Input -12 VdcPS03 - C31 +12 Input +12 VdcPS03 - C32 GND 0 Vdc


23

For Simulcast Interface Cards in slots 6, 9, 12, 15, and 18 replace the connector number with PS06, PS09, PS12, PS15, andPS18 respectively. In addition, reference to Signal Names starting with G01 are replaced with G02, G03, G04, G05, and G06respectively.

AE/LZB 119 1916/1 R1A PARTS LIST

24

CONTROL POINT TRUNKING SHELF

SXK 107 3847/2

SYMBOL PARTNUMBER

DESCRIPTION

1 SXA 120 4329/2 Card Cage, VME Shelf.

2 ROA 117 2256 Backplane printed wiring boardassembly. See separate parts list:

3 19A702364P213 Screw, M2.5 x 13, Pan head (qty:22).

4 19A700032P3 Lock Washer, Internal tooth, M2.5(qty: 22).

BACKPLANE ASSEMBLY

131-32 ROA 117 2256, Revision A

SYMBOL PARTNUMBER

DESCRIPTION

1 TVK 117 2228 R1 Control point/multi-layer print board

2 NFN 102 04 Fuse holder (qty 3 each)

3 RPV 403 143/901 Locking spring (qty 36 each)

------------------- FUSES -------------------

F1 NGH 241 04/8 Fuse 8.0 a t glass 5*20mm/glass-tube fuse

F2 NGH 241 04/2 Fuse 2.0 a t glass 5*20mm/glass-tube fuse

F3 NGH 241 03/8 Fuse 0.80a t glass 5*20m/glass-tube fuse

------------------- JACKS -------------------

J01 RPV 403 148/024 Header assembly/connector

J02 RPV 403 148/014 Press fit header for pwb/pinconnector unit
















J18 RNV 403 04/6 Connector





------------- CONNECTORS -------------

P01 RPT 403 407/015 15 pol/connector

PS01 RNV 403 844/096 Din, class 2,type c recepticle/forkcontact unit











ASSEMBLY DIAGRAM

CPTC SHELF VME CARD CAGESXK 107 3847/2

(151 88-SXK 107 3847/2, Sh. 1, Rev. A)

AE/LZB 119 1916/1 RIA

25

ASSEMBLY DIAGRAM

CARD CAGE ASSEMBLYSXA 120 4329/2(1301-SXA 120 4329, Sh. 1, Rev. A)

AE/LZB 119 1916/1 R1A

26

OUTLINE DIAGRAM

SIMULCAST TRUNKING SHELF BACKPLANEROA 117 2256

(1078-ROA 117 2256, Sh. 1, Rev. A)

AE/LZB 119 1916/1 RIA

27

OUTLINE DIAGRAM

SIMULCAST TRUNKING SHELF BACKPLANEROA 117 2256(1078-ROA 117 2256, Sh. 2, Rev. A)

AE/LZB 119 1916/1 R1A

28

SCHEMATIC DIAGRAM


(1911-ROA 117 2256, Sh. 1, Rev. A)

AE/LZB 119 1916/1 RIA

29

SCHEMATIC DIAGRAM


AE/LZB 119 1916/1 R1A

30

SCHEMATIC DIAGRAM


(1911-ROA 117 2256, Sh. 3, Rev. A)

AE/LZB 119 1916/1 RIA

31

SCHEMATIC DIAGRAM


AE/LZB 119 1916/1 R1A

32

SCHEMATIC DIAGRAM


(1911-ROA 117 2256, Sh. 5, Rev. A)

AE/LZB 119 1916/1 RIA

33

SCHEMATIC DIAGRAM


AE/LZB 119 1916/1 R1A

34

SCHEMATIC DIAGRAM


(1911-ROA 117 2256, Sh. 7, Rev. A)

AE/LZB 119 1916/1 RIA

35

SCHEMATIC DIAGRAM


AE/LZB 119 1916/1 R1A

36

SCHEMATIC DIAGRAM

CONTROL POINT TRUNKING SHELF CONFIGURATIONROA 117 2256

(19C852736, Sh. 1, Rev. A)

AE/LZB 119 1916/1 RIA

37

Ericsson Inc.Private Radio SystemsMountain View RoadLynchburg, Virginia 24502 AE/LZB 119 1916/1 R1A1-800-592-7711 (Outside USA, 804-592-7711) Printed in U.S.A.

AE/LZB 119 1916/1 R1A

Documents

LZB-1916R1A - EDACS SIMULCAST CONTROL POINT TRUNKING SHELF ... · EDACS SIMULCAST CONTROL POINT TRUNKING SHELF SXK 107 3847/2 TABLE OF CONTENTS ... This manual covers Ericsson and