LINAC 4 Emittance Meter. Linac 4 Emittance Meter 1er design for commissioning of the source Slit Sem-grid Measurement plate (F.C.) Emittance meter Upgrade

LINAC 4Emittance Meter

2

Linac 4 Emittance Meter

• 1er design for commissioning of the sourceSlitSem-gridMeasurement plate (F.C.)Emittance meter• Upgrade of the slit for 3MevNew slit

LINAC 4 Beam Instrumentation Review - 18-19 October 2011 D. GERARD BE/BI/ML

LINAC 4 Beam Instrumentation Review - 18-19 October 2011

3

SLIT

D. GERARD BE/BI/ML

SLIT 0.1 mmStainless steel plate: thickness 1 mm with 0.2 mm at the slit position


4D. GERARD BE/BI/ML

SEM-GRID

48 wires 40 µm Tungsten space 0.75 mm


5D. GERARD BE/BI/ML

SEM-GRID


6D. GERARD BE/BI/ML

SEM-GRID


7D. GERARD BE/BI/ML

SEM-GRID

Polarized plate


8D. GERARD BE/BI/ML

SEM-GRIDAngle setting


9D. GERARD BE/BI/ML

Measurement plate (F.C.)


10D. GERARD BE/BI/ML






12

Emittance Meter

D. GERARD BE/BI/ML


13

Emittance Meter

D. GERARD BE/BI/ML


14

Emittance Meter

D. GERARD BE/BI/ML


15

Emittance Meter

D. GERARD BE/BI/ML


16

Emittance Meter

D. GERARD BE/BI/ML


17

New Slit Design• Slit used at source front-end would reach too high temperatures at 3 MeV and

would not be thick enough at 12 MeV• New slit design based on

– Energy deposition: dilute energy deposition density by putting the blade with an angle w.r.t. beam axis

– Minimize scattering along slit gap: minimize slit thickness• New design based on graphite plates with an angle of 15 degrees w.r.t. beam

trajectory

D. GERARD BE/BI/ML


18

New Slit -Thermo-Mechanical Calculations (EN-MME)

D. GERARD BE/BI/ML

ANSYS Model Temperature Evolution during multi-shots

Without Cooling

With Cooling

Design Completed Fabrication Launched


19

Specification3 MeV 12 Mev

H- range in Carbon [mm] 0.1 1

Min/Max Slit thickness [mm] 2/5

Min single blade width [mm] 67

Min single blade height [mm] 67

Min slit fullstroke [mm] 134

Blade distance (slit gap) all along the slit thickness

[µm] 100, adjustable to 200

D. GERARD BE/BI/ML


20

NEW SLIT

D. GERARD BE/BI/ML


21

Graphite plateBEAMdirection15°

D. GERARD BE/BI/ML

NEW SLIT

Slit: 0.1 mm or 0.2 mm


22

wedge to adjust by machining after metrology measurement

D. GERARD BE/BI/ML

NEW SLIT


23

Additional graphite plates needed to cover the whole beam during the measurement

Five set of plates are ordered (3 spares)

D. GERARD BE/BI/ML

NEW SLIT


24

The back copper support of the graphite plate integrate the cooling circuit hole

D. GERARD BE/BI/ML

NEW SLIT


25

Two side plate close the cooling circuit. In the assembly, it is the only position where a brazing separate vacuum from the water of the cooling circuit

D. GERARD BE/BI/ML

NEW SLIT


26

Fixation of the graphite plate on the support

D. GERARD BE/BI/ML

NEW SLIT

Thickness at the slit position : 1 mm



NEW SLIT


28

NEW SLIT

Horizontal et vertical slit

D. GERARD BE/BI/ML


29

NEW SLITHorizontal et vertical slit movement with potentiometer

Window for laser profile measurement

Sliding support

D. GERARD BE/BI/ML

Stepping motor: 200 step / turn

Manipulator1.27 mm/turn => resolution 6.35 µm / motor step


30

NEW SLITSlope setting with the back micrometric screw

Tilt setting with the 2 front screw

D. GERARD BE/BI/ML

0.25 mm/ turn

BEAMPotentiometer will be added to the micrometric screw to be able to keep the position of the alignment setting


31

TILT setting

D. GERARD BE/BI/ML

Is done with a optical benchThe slit assembly is installed in the tank The tank is aligned to a optical bench (the survey target and the tilt reference plate are set).The assembly will be under vacuum.By acting on the 2 front micrometric screw the slit will be aligned

For the slope setting the assembly will stay on the same bench and under vacuum but a laser will replace the optical system.

Horizontal ref (or vertical) of the optical system

Several iteration by acting on the 2 micrometric screwsuntil getting the slit horizontal


32

Slope setting

D. GERARD BE/BI/ML

LASER BEAM

Laser beam sensor

Vertical movement of the laser

Mechanism under vacuum

Several iteration until getting the maximum value at the laser beam sensor

Setting the position of the slit by action on the back screw


33

NEW SLIT

D. GERARD BE/BI/ML


34

NEW SLIT

D. GERARD BE/BI/ML


35

Budget new slit

• Design: 93 kCHF• Manufacturing: 150 kCHF (88 kCHF + 60

KCHF)Total: ~250 kCHF

D. GERARD BE/BI/ML



Some pictures



GEFRAN PKM175 Répétitivité : 0.01 mm






40

Planning

• AP : delivery of the mechanical part earliest end of November.

• The supply parts are already at CERN except water flow, screw...

• Planning (working days):see next slide

D. GERARD BE/BI/ML


41

Planning 1. Assembly of the graphite plate, metrology lab, machining of the wedge, cleaning, reassembly and

remetrology lab:7 days 2. Assembly of the 2 slit out of the tank:10 working days 3. Assembly of the tank with the setting support on the optical alignement bench and alignment:3 working days 4. Assembly of the 2 slits inside the tank:2 working days 5. Tilt alignment of the 2 slits:2 working days Slope alignment of the 2 slits (not usual, probably with laser and captor):3 working days Check of the alignment and survey alignment2 working days

Mechanical assembly finish: 29 working days

But the position setting and check of the movement for the soft and hardware electronic needed to be done with the slit assembly on the optical alignment bench and with the support of the ML section

D. GERARD BE/BI/ML



Planning

If the delivery from the AP (Main Workshop) is end-of November Þ25/01/2012 the new slit will be ready (mechanical) BUT in parallel the Winter Shut Down !!!


43

• Thanks to:F. Roncarolo, B. CheymolB. Riffaud, E. Berthome, D. Steyaert, A.

DallochioG. Favre, S. Mathot M. Duraffourg, G. J. Focker....and all other people involved in this project

D. GERARD BE/BI/ML


44

Question?

• Thank for your attention• Question?

D. GERARD BE/BI/ML


45

Cut view

D. GERARD BE/BI/ML

Documents

LINAC 4 Emittance Meter. Linac 4 Emittance Meter 1er design for commissioning of the source Slit Sem-grid Measurement plate (F.C.) Emittance meter Upgrade