Upload
engr-gohar-mumtaz
View
217
Download
0
Embed Size (px)
Citation preview
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
1/114
Bandpass Modulation
&
Demodulation
Engr. Ghulam Shabbir
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
2/114
Modulation and Demodulation (MODEM)
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
3/114
Digital Communication System
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
4/114
Modulation and Demodulation (MODEM)
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
5/114
Baseband vs. Bandpass Communications
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
6/114
Baseband vs. Bandpass Communications
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
7/114
Baseband vs. Bandpass Communications
Bandpass transmission involves some translation ofthe baseband signal to some band of frequencycentered around fc
Bandpass Transmitter:
Carrier (high frequency pure sinusoidal generated by thelocal oscillator) is altered in response to a given low
frequency signal (message signal) generated by the source
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
8/114
8
Bandpass Modulation and Demodulation
Bandpass Modulation is the process by which somecharacteristics of a sinusoidal waveform is variedaccording to the message signal.
Modulationshifts the spectrum of a baseband signalto some high frequency.
Demodulator/Decoder baseband waveform recovery
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
9/114
Modulation Modulation - process (or result of the process)
of translation of the baseband message signalto bandpass (modulated carrier) signal at
frequencies that are very high compared to thebaseband frequencies.
Demodulation is the process of extracting thebaseband message back the modulated carrier.
An information-bearing signal is non-deterministic, i.e. it changes in an unpredictablemanner.
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
10/114
Modulation & Demodulation
Baseband
Modulation
CarrierRadio
Channel
Synchronization/Detection/
Decision
Carrier
Data in Data out
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
11/114
Modulation Modulation is a process of mixing a signal with a
sinusoid to produce a new signal. This new signal, conceivably, will have certain
benefits of an un-modulated signal, especially duringtransmission.
If we look at a general function for a sinusoid:f(t) =A sin (t+)
This sinusoid has the following 3 parameters that canbe altered, to affect the shape of the graph.
1. A, is called the magnitude, or amplitude of thesinusoid.
2. The term , is known as the frequency3. The term, is known as the phase angle.
All 3 parameters can be altered to transmit data.
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
12/114
Modulation The sinusoidal signal that is used in the
modulation is known as the carrier signal, orsimply "the carrier".
The signal that is used in modulating the carriersignal (or sinusoidal signal) is known as the "datasignal" or the "message signal".
It is important to notice that a simple sinusoidalcarrier contains no information of its own.
In other words we can say that modulation isused because some data signals are not alwayssuitable for direct transmission, but themodulated signal may be more suitable.
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
13/114
Why Modulate? Digital modulation is the process by which digital
symbols are transformed into waveforms that arecompatible with characteristics of the channel.
In the case of baseband modulation, thesewaveforms usually take the form of shaped pulses.
But in the case of bandpass modulation the shapedpulses modulate a sinusoid called a carrier wave, orsimply a carrier; for radio transmission the carrieris converted to an electromagnetic (EM) field ofpropagation to the desired destination.
The transmission of EM fields through space isaccomplished with the use of antennas.
Why it is necessary to use a carrier for the radiotransmission of baseband signals
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
14/114
Why Modulate? The size of the antenna depends on the wavelength and
the application.
For cellular telephones, antennas are typically /4 in size,where wavelength is equal to c/f, and c, the speed of light, is
3 x 108 m/s.
Most channels require that the baseband signal be shifted toa higher frequency.
For example in case of a wireless channel antenna size isinversely proportional to the center frequency, this isdifficult to realize for baseband signals.
For speech signal f = 3kHz = c/f = (3x108) / (3x103) Antenna size without modulation /4=105 /4 meters = 15
miles - practically unrealizable
Same speech signal if amplitude modulated using fc= 900MHz will require an antenna size of about 8cm.
For this reason, carrier-wave or bandpass modulation is anessential step for all systems involving radio transmission.
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
15/114
It means that we need height of antenna equal to 105m or 100 km! This is practically impossible!
However we can reduce its height by l/2, l/4, l/8 or up
to l/16. But even if we reduce it to l/16, it becomes 6.2km, which is still impossible! Therefore, we cannottransmit low frequency signals directly.
As per above equation, if we increase frequency ofelectrical signal the height will reduce.
However, this creates one more problem! We want totransmit electrical signals in audio range. But, ourhighest audio frequency is 20 kHz. For this, height ofantenna will be around 15 km. This height is also
impossible!
Why Modulate?
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
16/114
This height is practically easily possible!
Also, our voice frequency constantly changes. So we willhave to change height of antenna constantly. So all theseproblems are absurd.
The only solution to this problem----- is the process ofmodulation.
In modulation very high frequency, carrier wave is taken.It is modulated (in either AM or FM style) by modulatingsignal, which we want to transmit actually.
After modulation, low frequency RIDESover carrier wave. This modulated carrier wave is connected to antenna for
transmission.
Now suppose we want to transmit 3 kHz signal, with 300MHz carrier wave. Then actually, 300 MHz signal is
transmitted. For this height of antenna will be
Why Modulate?
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
17/114
Why Modulate? Now carrier signal will be transmitted with modulating
signal and at some distance, we shall receive it. In receiver, we want 3 kHz signal actually. So by another
process of DEMODULATION, we shall filter outunwanted 300 MHz signal and remaining PURE 3 kHzsignal will be used.
Bandpass modulation can provide other importantbenefits in signal transmission. If more than one signalutilizes a single channel, modulation may be used toseparate the different signals.
Modulation can be used to minimize the effects of
interference. A class of such modulation schemes, known as spread-
spectrum modulation, requires a system bandwidthmuch larger than the minimum bandwidth that would berequired by the message.
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
18/114
Why Modulate?
Modulation can also be used to place a signal in afrequency band where design requirements, such afiltering and amplification, can be easily met. This is thecase when radio-frequency (RF) signals are converted toan intermediate frequency (IF) in a receiver.
This is evident that efficient antenna of realistic physicalsize is needed for radio communication system
For this reason, carrier-wave or bandpass modulation isan essential step for all systems involving radiotransmission.
Modulation also required if channel has to be shared byseveral transmitters (Frequency division multiplexing).
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
19/114
WhyCarrier ?
Effective radiation of EM waves requires antennadimensions comparable with the wavelength:
Antenna for 3 kHz would be ~100 km long
Antenna for 3 GHz carrier is 10 cm long
Sharing the access to the telecommunication channelresources
Amplitude, frequency and phase of a carrier can bevaried according to the message signal.
Three ways of representing a modulated signal (M&P,I&Q and complex envelope).
ASK generation and demodulation/detection
FM (or FSK) equivalent to modulating the phase of the
carrier by the integral of the message signal.
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
20/114
Bandpass modulation (either analog or digital) is the processby which an information signal is converted to a sinusoidal
waveform; for digital modulation, such a sinusoid of duration Tis referred to as a digital symbol.
The sinusoid has just three features that can be used todistinguish it from other sinusoids:
Amplitude
Frequency
Phase
Thus bandpass modulation can be defined as the processwhereby the amplitude, frequency or phase of an RF carrier, or
a combination of them, is varied in accordance with theinformation to be transmitted.
The general form of the carrier wave is
s(t)= A(t) cos(t)
where A(t)is the time-varying amplitude and (t) is the time-
varying angle.
DigitalBandpassModulation
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
21/114
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
22/114
It is convenient to write (t) = (t) + (t), so that
s(t) = A(t) cos ( (t) +(t))
=A(t) cos (2fct +(t))
where 0 is the radian frequency of the carrier,(t) is the phase ; and = 2fc The three parameters (amplitude, frequency and
phase) can be varied in analog or digital form.
When varied in digital form, it is referred to asShifting & Keying.
DigitalBandpassModulation
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
23/114
The basic bandpass modulation / demodulation
types are listed as under:
DigitalBandpassModulation
When the receiver exploits knowledge of thecarriers phase to detect the signals, the process iscalled coherent detection
When the receiver does not utilize such phasereference information, the process is called non-
coherent detection.
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
24/114
Modulation Process
Modulation implies varying one or morecharacteristics (modulation parameters a1, a2, an) of a carrier f in accordance with the
information-bearing (modulating) basebandsignal.
Sinusoidal waves, pulse train, square wave,etc. can be used as carriers
1 2 31 2 3
, , , ... , (= carrier), , ,... (= modulation parameters)
(= time)
n
n
f f a a a a ta a a a
t
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
25/114
Digital Bandpass Modulation TechniquesThree ways of representing bandpass signal:
(1) Magnitude and Phase (M & P)
Any bandpass signal can be represented as:
A(t) 0is real valued signal representing the magnitude
(t) is the genarlized angle (t)is the phase
The representation is easy to interpret physically, but often isnot mathematically convenient
In this form, the modulated signal can represent informationthrough changing three parameters of the signal namely:
Amplitude A(t) : as inAmplitude Shift Keying (ASK)
Phase (t) : as inPhase Shift Keying (PSK)
Frequency d(t)/dt : as in Frequency Shift Keying (FSK)
)](cos[)(cos[)()( 0 tttAttAts
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
26/114
Continuous Carrier
Carrier: A sin[t +]
A = const
= const = const
Amplitude modulation(AM)
A = A(t) carries information = const
= const
Frequency modulation(FM)
A = const
= (t) carries information
= const
Phase modulation (PM)
A = const = const
= (t) carries information
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
27/114
There are three major classes of digital modulation techniquesused for transmission of digitally represented data:
1. Amplitude Shift Keying (ASK)1. Frequency Shift Keying (FSK)
2. Phase-shift keying (PSK)
All convey data by changing some aspect of a base signal, thecarrier wave (usually a sinusoid), in response to a data signal.
In the case of PSK, the phase is changed to represent the datasignal.
There are two fundamental ways of utilizing the phase of asignal in this way:
1. By viewing the phase itself as conveying theinformation, in which case the demodulator must have areference signal to compare the received signal's phaseagainst; or
2. By viewing the changein the phase as conveyinginformation differential schemes, some of which do
not need a reference carrier (to a certain extent).
Digital Bandpass Modulation Techniques
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
28/114
Angle Modulation
Angle modulation is a class of analog modulation.
In this type of modulation, the frequency or phase ofcarrier is varied in proportion to the amplitude of themodulating signal.
Frequency and phase modulation are also known asAngle Modulation.
These techniques are based on altering the angle (orphase) of a sinusoidal carrier wave to transmit data,as opposed to varying the amplitude, such as in AMtransmission.
Figure:
An angle modulated signal
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
29/114
0( ) ( ) cos( ( )) ( ) cos( )s t A t t A t t
0
)()(
dt
tdti
dtt
i )()(
Angle Modulation
Consider a signal with constant frequency:
Frequency is the derivative of phase or the rate of change ofphase. The instantaneous frequency can be written as:
or
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
30/114
Then considering a message signal
m(t) = Amcos (2fmt),
we can write the phase modulation as
0( ) ( )pt t K m t
0( ) cos[ ( )]PM ps t A t K m t
0( ) ( )i pd
t K m t dt
Phase Shift Keying (PSK) or PM
If we consider an angle modulated signal s(t) = A cos (t)
or a phase modulated signal as
where i= 2fc and
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
31/114
In case of frequency modulation for a message signal
m(t) = Amcos (2fmt)
0( ) ( )i ft K m t
0( ) [ ( )]t
ft K m t d
0 ( )
t
ft K m d
0
0
( ) cos[ ( ) ]
cos[ ( )]
t
FM f
f
s t A t K m d
A t K a t
where:
( ) ( )
t
a t m d
Frequency Shift Keying (FSK) or FM
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
32/114
0 0.05 0.1 0.15
-1
-0.5
0
0.5
1
The message signal
0 0.05 0.1 0.15
-1
-0.5
0
0.5
1
Time
The modulated signal
Example
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
33/114
% Matlab script for generating FM via Phase modulation
clear all;close all;
t0=.15; % signal duration
ts=0.0005; % sampling interval
fc=200; % carrier frequency
kf=100; % Modulation index
fs=1/ts; % sampling frequency
t=[0:ts:t0]; % time vector
df=0.25; % required frequency resolution%message signal
m=[ones(1,t0/(3*ts)),-1*ones(1,t0/(3*ts)),ones(1,t0/(3*ts)+1)];
int_m(1)=0;
for i=1:length(t)-1 % Integral of m
int_m(i+1)=int_m(i)+m(i)*ts;
end
u=cos(2*pi*fc*t+2*pi*kf*int_m); % phase modulating with the% integral of the signal
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
34/114
Phasor Representation of AmplitudeModulation
Consider the AM signal in phasor form:
0( ) Re 12 2
m mj t j tj t e e
s t e
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
35/114
Phasor Representation of FM
Consider the FM signal in phasor form:
0( ) Re 12 2
m mj t j t j ts t e e e
Di it l d l ti ( ) PSK (b) FSK ( ) ASK (d) ASK/PSK (APK)
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
36/114
Digital modulations, (a) PSK (b) FSK (c) ASK (d) ASK/PSK (APK)
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
37/114
Amplitude Shift Keying Modulation Process
In Amplitude Shift Keying (ASK), the amplitude of the carrier is switchedbetween two (or more) levels according to the digital data
For BASK (also called ON-OFF Keying (OOK)), one and zero are representedby two amplitude levels A1and A0
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
38/114
Analytical Expression:
where Ai=peak amplitude
Hence,
where
00,0
10),cos()(
binaryTt
binaryTttAts
ci
)cos(2)cos(2)cos()( 02
00 tAtAtAts rmsrms
R
V
PtT
E
tP
2
00 )cos(
2
)cos(2
1,......2,0,00,0
10),cos()(2
)( Mi
binaryTt
binaryTttT
tEts i
i
i
1,......2,0,)(0
2 MidttsET
i
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
39/114
Where for binary ASK (also known as ON OFF Keying (OOK))
Mathematical ASK Signal Representation
The complex envelopeof an ASK signal is:
The magnitudeand phaseof an ASK signal are:
The in-phase and quadrature components are:
the quadrature component is wasted.
1( ) ( ) cos( ), 0 1c cs t A m t t t T binary
0 ( ) 0, 0 0s t t T binary
)()( tmAtg c
0)(),()( ttmAtA c
)()( tmAtx c
,0)( ty
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
40/114
It can be seen that thebandwidth of ASKmodulated is twice thatoccupied by the source
baseband stream
Bandwidth of ASK
Bandwidth of ASK can be found from its power spectral density
The bandwidth of an ASK signal is twice that of the unipolar NRZline code used to create it., i.e.,
This is the null-to-null bandwidth of ASK
b
bT
RB 22
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
41/114
If raised cosine rolloff pulse shaping is used, then the bandwidthis:
Spectral efficiency of ASK is half that of a baseband unipolar NRZline code
This is because the quadrature component is wasted
(1 )b
B r R
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
42/114
Detectors for ASK (Coherent Receiver)
Coherent detection requires the phase information
A coherent detector mixes the incoming signal with a locallygenerated carrier reference
Multiplying the received signal r(t)by the receiver local oscillator
(say Accos (wct))yields a signal with a baseband component plusa component at 2fc
Passing this signal through a low pass filter eliminates the highfrequency component
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
43/114
The output of the LPF is sampled once per bit period This sample z(T)is applied to a decision rule
z(T)is called the decision statistic
Matched filter receiver of OOK signal
A MF pair such as the rootraised cosine filter can thus beused to shape the source and
received baseband symbols In fact this is a very common
approach in signal detection inmost bandpass data modems
N h R i
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
44/114
Noncoherent Receiver
Does not require a phase reference at the receiver
If we do not know the phase and frequency of the
carrier, we can use a noncoherent receiverto recoverASK signal
Envelope Detector:
The simplest implementation of an envelope detector
comprises a diode rectifier and smoothing filter
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
45/114
Phase Shift Keying (PSK)
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
46/114
Phase Shift Keying (PSK)
These signals are called antipodal.
The reason that they are chosen is that they have acorrelation coefficient of -1, which leads to theminimum error probability for the same Eb/No.
These two signals have the same frequency andenergy.
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
47/114
Phase Shift Keying (PSK)BINARY PSK
All PSK signals can be graphically represented by asignal constellation in a two-dimensional coordinatesystem with 1(t) and 2(t) as its horizontal andvertical axis, respectively under:
Figure: BPSK signal constellation
and
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
48/114
Phase Shift Keying (PSK) In PSK, the phase of the carrier signal is switched
between 2 (for BPSK) or more (for MPSK) in response to
the baseband digital data
With PSK the information is contained in theinstantaneous phase of the modulated carrier
Usually this phase is imposed and measured with respect
to a fixed carrier of known phase Coherent PSK For binary PSK, phase states of 0o and 180o are used
Waveform:
PSK Generation
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
49/114
PSK Generation
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
50/114
Phase shift keying (PSK) was developed during the earlydays of the deep-space program. PSK is now widely usedin both military and commercial communications
systems.
The general analytical expression for PSK can be writtenas
where
g(t)is signal pulse shape
A = amplitude of the signal. It is a peak value of the
waveform. = carrier phase
c= 2fc
( ) ( ) cos[ ( )], 0 , 1, 2,....,i c i bs t A g t t t t T i M
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
51/114
Waveform Amplitude Coefficient
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
52/114
Waveform Amplitude CoefficientThe waveform amplitude coefficient appearing in the equation of PSKhas same general form modulation formats. The derivation ofthis expression begins with
where A is the peak value of the waveform. Since the peak value ofthe sinusoidal waveform equals times the root-mean-square(rms) value, we can write
assuming the signal to be a voltage or a current waveform, A2rmsrepresents average power P (normalized to 1). Therefore, we can
write
Replacing P watts by E joules/T seconds, we get
So, we shall use either the amplitude A in above equation or
tcosAts )(
TE/2
2
tcosAts rms 2)(
tcos rms2 2
tcosPts 2)(
t)( cos T
2Ets
TE/2
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
53/114
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
54/114
We can also write a PSK signal as:
Furthermore, s1(t) may be represented as a linear combination oftwo orthogonal functions 1(t) and 2(t) as follows
Where
M
it
T
Ets ci
)1(2cos
2)(
tM
it
M
i
T
Ecc
cossin
)1(2sincos
)1(2cos
2
)()1(2
sin)()1(2
cos)( 21 tM
iEt
M
iEtsi
]sin[2
)(]cos[2
)( 21 tT
tandtT
t cc
yxyxyx sinsincoscos)cos(
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
55/114
Using the concept of the orthogonal basis function, wecan represent PSK signals as a two dimensional vector
For M-ary phase modulation M = 2k, where kis the numberof information bits per transmitted symbol
In an M-ary system, one of M 2possible symbols, s1(t),, sm(t), is transmitted during each Ts- second signalinginterval
The mapping or assignment of kinformation bits into
M = 2kpossible phases may be performed in many ways,e.g. for M = 4
21
)1(2sin,
)1(2cos)(
M
iE
M
iEts bbi
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
56/114
A preferred assignment is to use Gray code in which
adjacent phases differ by only one binary digit such thatonly a single bit error occurs in a k-bit sequence.
It is also possible to transmit data encoded as the phasechange (phase difference) between consecutive symbols
This technique is known as Differential PSK (DPSK)
There is no non-coherent detection equivalent for PSKexcept for DPSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
57/114
M-ary PSK In MPSK, the phase of the carrier takes on one of Mpossible
values
Thus, MPSK waveform is expressed as
Each si(t)may be expanded in terms of two basis function 1(t)and 2(t)defined as
MiM
iti ,.....,2,1,)1(2)(
M
itTEtsi
)1(2cos2)( 0
M
ittgtsi
)1(2cos)()( 0
...........
1616
884
2
2
PSK
PSKQPSK
BPSK
MPSKM k
,cos2
)(1 tT
t cs
,sin2
)(2 tT
t cs
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
58/114
Quadrature PSK (QPSK) Two BPSK in phase quadrature
QPSK (or 4PSK) is a modulation technique that transmits 2-bitof information using 4 states of phases
For example
General expression:
2-bit Information
00 0
01 /2
10
11 3/2
Each symbol correspondsto two bits
sc
s
sQPSK Tti
M
itf
T
Ets
04,3,2,1,
)1(22cos
2)(
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
59/114
We can also have:
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
60/114
sc
s
sQPSK Tti
M
it
T
Ets
04,3,2,1,
4
)1(2cos
2)(
We can also have:
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
61/114
One of 4 possible waveforms is transmitted during each signalinginterval Ts
i.e., 2 bits are transmitted per modulation symbol Ts=2Tb)
In QPSK, both the in-phase and quadrature components are used
The I and Q channels are aligned and phase transition occur onceevery Ts= 2Tbseconds with a maximum transition of 180 degrees
From
As shown earlier we can use trigonometric identities to show that
Mitf
TEts c
s
sQPSK )1(22cos2)(
)sin()1(2sin2)cos()1(2cos2)( tM
iTEt
Mi
TEts c
s
sc
s
sQPSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
62/114
In terms of basis functions
we can write sQPSK(t) as
With this expression, the constellation diagram can easily be drawn For example:
tfT
tandtfT
t cs
c
s
2sin2
)(2cos2
)( 21
)(
)1(2sin)(
)1(2cos)( 21 t
M
iEt
M
iEts ssQPSK
Coherent Detection
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
63/114
Coherent Detection
1. Coherent Detection of PSK
Coherent detection requires the phase information
A coherent detector operates by mixing the incoming data signalwith a locally generated carrier reference and selecting thedifference component from the mixer output
Multiplying r(t) by the receiver LO (say A cos(ct)) yields a signalwith a baseband component plus a component at 2fc
The LPF eliminates the high frequency component The output of the LPF is sampled once per bit period
The sampled value z(T) is applied to a decision rule
z(T) is called the decision statistic
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
64/114
Matched filter receiver
A MF pair such as the root raised cosine filter can thus be used toshape the source and received baseband symbols
In fact this is a very common approach in signal detection in mostbandpass data modems
2 Coherent Detection of MPSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
65/114
2. Coherent Detection of MPSK
QPSK receiver is composed of 2 BPSK receivers
one that locks on to the sine carrier and
the other that locks onto the cosine carrier
tAt 01 cos)(
tAt 02 sin)(
2
0 0 1 0 0 00 0
( ) ( ) ( ) ( cos ) ( cos )2
s sT T sA Tz t s t t dt A t A t dt L
1 0 2 0 00 0
( ) ( ) ( ) ( cos ) ( sin ) 0s sT T
z t s t t dt A t A t dt
)cos( 00 tAs
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
66/114
If
Decision:
1. Calculate zi(t) as
2. Find the quadrant of (Z0, Z1)
Output S0(t) S1(t) S2(t) S3(t)
Z0 Lo 0 -Lo 0
Z1 0 -Lo 0 Lo
)45cos()()45cos()( 0201oo
tAtandtAt
Output S0(t) S1(t) S2(t) S3(t)
Z0 Lo -Lo -Lo Lo
Z1 Lo Lo -Lo -Lo
dtttrtz iT
i )()()( 0
4cos
2
2
0
sTAL
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
67/114
A coherent QPSK receiver requires accurate carrier recovery usinga 4th power process, to restore the 90ophase states to modulo 2
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
68/114
Correlation Receiver
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
69/114
T
0
T
0
comparator selectssi(t)
with max zi(t)
Decision Stage
reference signal
.
.
.
.
..
.
.
.
.
.
.
)(1 t
)(tM
dtttrTzT
)()()( 10
1
dtttrTz MT
M )()()(0
T
0
T
0
comparator selectssi(t)
with max zi(t)
)( tsi
Decision Stage)(1 ts
reference signal
)(tsM
.....
.
......
dttstrTzT
)()()( 10
1
dttstrTz MT
M )()()(0
)()()( tntstr i
)( ts
i)()()( tntstr i
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
70/114
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
71/114
)()()( 11 ttats ii
Transmitted signals si(t) in terms of 1(t) and coefficients ai1(t) are
Assume that s1 was transmitted, then values of product integratorswith reference to 1 are
)()()()( 11111 tEttats
)()()()( 11212 tEttats
T
dtttntEEszE0
1
2
11)()()(|
1
T
dtttntEEszE0
12
12)()()(|
1
22
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
72/114
where E{n(t)}=0
Decision stage determines the the location of the transmitted signalwithin the signal space
For antipodal case choice of 1(t) = 2/T cosw0t normalizes E{zi(T)}to E
Prototype signals si(t) are the same as reference signals j(t) exceptfor normalizing scale factor
Decision stage chooses signal with largest value of zi(T)
EdttT
tntET
EszET
0 002
11 c os2
)(c os2
|
Edtt
TtntE
TEszE
T
0 00
2
12cos
2)(cos
2|
Sampled Matched Filter
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
73/114
Sampled Matched Filter
The impulse response h(t) of a filter matched to s(t) is:
Let the received signal r(t) comprise a prototype signal si(t) plusnoise n(t)
Bandwidth of the signal is W =1/2T where T is symbol time then Fs= 2W = 1/T
Sample at t =kTs . This allows us to use discrete notation:
Let ci(n) be the coefficients of the MF where n is the time index andN represents the samples per symbol
elsewhere
TttTsth 0
0)()(
,...1,02,1)()()( kiknkskr i
])1[()( nNsnc ii
(eq 4.26)
(eq 4.27)
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
74/114
Discrete form of convolution integral suggests
Since noise is assumed to have zero mean, so the expected valueof a received sample is:
Therefore, if si(t) is transmitted, the expected MF output is:
Combining eq (4.27) and (eq 4.29) to express the correlator outputs
at time k = N1 = 3:
Nmodulo,.....,1,0)()()(1
0
Kncnkrkz i
N
n
i
2,1)()( ikskrEi
Nmodulo,.....,1,0)()()(1
0
KncnkskzE i
N
n
ii
(eq 4.28)
(eq 4.29)
3
1 1 1
0
( 3) (3 ) ( ) 2n
z k s n c n
3
2 1 2
0
( 3) (3 ) ( ) 2n
z k s n c n
(eq 4.30a) (eq 4.30b)
Sampled
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
75/114
p
Matched
Filter
Fig 4.10
Coherent Detection of MPSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
76/114
The signal space for a multiple phase-shift keying (MPSK) signal setis illustrated for a four-level (4-ary) PSK or quadriphase shiftkeying(QPSK)
Fig 4.11
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
77/114
At the transmitter, binary digits are collected two at a time for eachsymbol interval
Two sequential digits instruct the modulator as to which of the four
waveforms to produce si(t) can be expressed as:
where:E: received energy of waveform over each symbol duration T
w0: carrier frequency
Assuming an ortho-normal signal space, the basis functions are:
tT
t 01 cos2
)(
Mi
Tt
M
it
T
Etsi
,...1
0)
2cos(
2)( 0
tT
t 02 sin2
)(
si(t) can be written in terms of these orthonormal coordinates:
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
78/114
si(t) can be written in terms of these orthonormal coordinates:
The decision rule for the detector is:
Decide that s1(t) was transmitted if received signal vector fall inregion 1
Decide that s2(t) was transmitted if received signal vector fall inregion 2 etc
i.e choose ith waveform if zi(T) is the largest of the correlatoroutputs
The received signal r(t) can be expressed as:
Mi
Tttatats iii
,...1
0)()()( 2211
)(2sin)(2cos 21 tM
iEtM
iE
Mi
Tttntt
T
Etr ii
,...1
0)(sinsincoscos
2)( 00
The upper corelator computes dtttrXT
)()(
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
79/114
The upper corelator computes
The lower corelator computes
dtttrX )()( 10
dtttrYT
)()( 20
The computation of the received
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
80/114
pphase angle can beaccomplished by computing thearctan of Y/X
Where:X: is the inphase component of thereceived signal
Y: is the quadrature component ofthe received signal
: is the noisy estimate of thetransmitted i
The demodulator selects the ithat is closest to the angle
Or it computes | i - | for each iprototypes and chooses i yieldingsmallest output
Fig 4.13
Coherent Detection of FSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
81/114
FSK modulation is characterized by the information in the frequencyof the carrier
Typical set of FSK signal waveform:
Where : is an arbitrary constant
E: is the energy content of si(t) over each symbol duration T
(wi+1- wi): is typically assumed to be an integral multiple of /T
Assuming the basis functions form an orthonormal set:
Amplitude 2/T normalizes the expected output of the MF
Mi
Ttt
T
Ets ii
,...1
0)cos(
2)(
NjtT
t jj ,....,1cos2
)(
dttT
tT
Ea ji
T
ij )cos(2
)cos(2
0
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
82/114
Therefore
This implies, the ith prototype signal vector is located on the ith
coordinate axis at a displacement E from the origin of the symbolspace
For general M-ary case and given E, the distance between any twoprototype signal vectors si and sj is constant:
otherwise
jiforEaij
0
jiforEssssd jiji 2||||),(
Signal space partitioning for 3-ary FSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
83/114
NONCOHERENT DETECTION
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
84/114
Detection of Differential PSK DPSK refers to a detection scheme classified as noncoherent
because it does not require a reference in phase with the received
carrier Therefore if the transmitted waveform is:
The received signal can be characterized by:
is an arbitrary constant ; assumed to be uniform random variabledistributed between 0and 2n(t):AWGN process
Mi
Tttt
T
Ets ioi
,....1
0)](cos[
2)(
Mi
Tttntt
T
Etr io
,....1
0)(])(cos[
2)(
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
85/114
If we assume that varies slowly relative to two period times(2T),the phase difference between two successive waveforms j(T1)andk(T2) is independent of :
Basis for differentially coherent detection of differentially encoded
PSK is: Carrier phase of previous signaling interval is used as phase
reference for demodulation
Its use requires differentially encoded message signal at thetransmitter since information is carried by difference in phase
between successive waveforms
)()()()()( 21212 TTTTT ijkjk
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
86/114
Detector in general calculates thecoordinates of the incoming signal
by correlating it with locallygenerated waveforms such as:2/T cosw0t and 2/T sinw0t
The detector then measures the
angle between the currentlyreceived signal vector and thepreviously received signal vector.
Fig 4.16 Signal space for DPSK
Detection of Binary PSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
87/114
Sample Index,k 0 1 2 3 4 5 6 7 8 9 10Information Message,ak 1 1 0 1 0 1 1 0 0 1
Differentially Encodedmessage (first bitarbitrary), dk
1 1 1 0 0 1 1 1 0 1 1
Corresponding phaseshift, k
0 0 0 0 0 0 0 0
Differential Encoding
kkk add 1
kkk
add 1
Encoding Schemes
Decoding Scheme
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
88/114
Sample Index,k 0 1 2 3 4 5 6 7 8 9 10
r(k) 0 0 0 1 1 0 0 0 1 0 0
1 1 0 1 0 1 1 0 0 1
)( ka
1 kkk rra
Advantages1) Phase ambiguity can be resolved
2) Non-coherent detection techniques can be used
)( ka
Sample Index,k 0 1 2 3 4 5 6 7 8 9 10r(k) 1 1 1 0 0 1 1 1 0 1 1
1 1 0 1 0 1 1 0 0 1
Drawback of Differential Encoding/Decoding:
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
89/114
)( ka
Sample Index,k 0 1 2 3 4 5 6 7 8 9 10
r(k) 1 1 1 1 0 1 1 1 0 1 1
1 1 1 0 0 1 1 0 0 1
2-bits in error
When single bit errors occur in the received data sequence dueto noise, they tend to propagate as double bit errors
Since the decoder is comparing the logic state of current bit withprevious bit, and if the previous bit is in error, the next decoded bitwill also be in error
Differentially Encoded PSK (DEPSK) Modulation
Th d d {d } i d t h hift i ith
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
90/114
The encoded sequence {dk} is used to phase-shift a carrier withphase angle 0 and representing symbols 1 and 0respectively
Method for the detection of DEPSK
Coherent detection of PSK followed by differential decoder (dk isequivalent to rk in the previous slides)
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
91/114
In DPSK, the carrier phase of the previous data bit can be usedas a reference
Detection of FSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
92/114
The demodulator must be configured as an energy
detector, without exploiting phase measurements
For this reason noncoherent detector requires twice asmany channel branches as the coherent detector.
One implementation can be obtained by using the in-phase (I) and quadrature (Q) channels to detect a binaryFSK (BFSK) as shown in the next slide.
{Correlation Squaring
I and Q energy
Summation Test statistic and
decision
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
93/114
T
0
T
0
Decision Stage
I channel
Q channel
2
(.)
2(.)
tT 1cos/2
tT1sin/2
)(1 Tz
)(2 Tz
)(21
Tz
)(2
2Tz
T
0
T
0
I channel
Q channel
2(.)
2(.)
tT 2cos/2
tT 2sin/2
)(3 Tz
)(4 Tz
)(23
Tz
)(24 Tz
TzTz ()( 242
3
)()(2
2
2
1 TzTz
)(tr )(Tz
2H
1H
0)(Tz
)( tsiDecision Stage
{ { { {
Fig 4.18
One of the simplest ways of detecting binary FSK is to pass the
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
94/114
One of the simplest ways of detecting binary FSK is to pass thesignal through 2 Band Pass Filters(BPF) tuned to the 2 signalingfreqs and detect which has the larger output averaged over a
symbol period
An envelope detector consists of a rectifier and a low pass filter
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
95/114
An envelope detector consists of a rectifier and a low-pass filter
Detectors are matched to signal envelopes and not to signalsthemselves
For BFSK, decision is made on the basis of maximum amplitudeamongst the two envelope detectors
For MFSK, decision is made on the basis of which of the Menvelope detectors has the maximum output
Fig 4.19
Required Tone Spacing for Noncoherent
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
96/114
Orthogonal FSK Signaling
FSK is usually implemented as orthogonal signaling, but not all FSKsignaling is orthogonal
How can we tell
If the two tones f1 and f2 are orthogonal to each other
Or they are uncorrelated over symbol time T
Property: any pair of tones in the set must have a frequencyseparation that is a multiple of 1/T Hz
A tone with frequency f1 that is switched on for a symbol duration Tseconds and then switched off can be analytically described as:
))/()2(cos()( Ttrecttfts ii
2/||0
2/2/1)/(
Ttfor
TtTforTtrect
Fourier transform of si(t):
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
97/114
The spectra of two such adjacent tones: tone1 with frequency f1 andtone 2 with frequency f2 are shown:
TffcTts ii )(sin)}({
Fig 4.20
F FSK th b d idth i t l t d t th t l
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
98/114
For FSK the bandwidth requirements are related to the spectralspacing between the two tones
The frequency difference between the center of the spectral main
lobe and the first zero crossing represents the minimum requiredspacing
With noncoherent detection, this corresponds to a minimum toneseparation of 1/T Hz.
For coherent detection, this corresponds to a minimum toneseparation of 1/2T Hz.
See Example 4.3, Page 202.
Example 4.3: Non-coherent FSK signaling
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
99/114
Two waveforms for: where f1>f2, thesymbol rate 1/T and = a constant arbitrary angle
(a) Prove that the minimum tone spacing for non coherentlydetected orthogonal FSK signaling is 1/T
1 2cos(2 ) cos 2f t and f t
1 2
0
cos(2 )cos 2 0
T
f t f t dt
1 2 1 2
0 0
cos cos 2 cos 2 sin sin 2 cos2 0
T T
f t f t dt f t f t dt
1 2 1 2
0
cos [cos 2 ( ) cos 2 ( ) ]T
f f t f f t dt 1 2 1 2
0
sin [sin 2 ( ) sin 2 ( ) ] 0T
f f t f f t dt
(eq 4.45)
T
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
100/114
1 2 1 2
1 2 1 2 0
sin 2 ( ) sin 2 ( )cos
2 ( ) 2 ( )
T
f f t f f t
f f f f
1 2 1 2
1 2 1 2 0
cos 2 ( ) cos 2 ( )sin 02 ( ) 2 ( )
T
f f t f f tf f f f
1 2 1 2
1 2 1 2
sin 2 ( ) sin 2 ( )cos
2 ( ) 2 ( )
f f T f f T
f f f f
1 2 1 2
1 2 1 2
cos 2 ( ) 1 cos 2 ( ) 1sin 0
2 ( ) 2 ( )
f f T f f T
f f f f
Assume that f1+f2 >> 1
1 2 1 2
1 2 1 2
sin 2 ( ) cos 2 ( )0
2 ( ) 2 ( )
f f T f f T
f f f f
(eq 4.49)
(eq 4.50)
C bi i 4 49 & 4 50
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
101/114
1 2 1 2cos sin 2 ( ) sin cos2 ( ) 1 0f f T f f T
1 2
1 2
Note that for arbitrary , the termseq4.51cansum to0 only when sin 2 ( ) 0
andsimultaneouslycos2 ( ) 1
f f T
f f T
sin 0x for x n and
cos 1 2 integersx for x k where n and k are
:for arbitrary
1 22 ( ) 2f f T k or 1 2k
f fT
1 2
1(minimum 1)f f tone spacing at k
T
Combining eq-4.49 & eq-4.50
(eq 4.51)
(eq 4.52)
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
102/114
(b) What is the minimum tone spacing for coherently detectedorthogonal FSK signaling?
For coherent detection we need to satisfy eq 4.45 for = 0instead of any arbitrary phase. Rewriting eq 4.51 for = 0
Or
1 2sin 2 ( ) 0f f T
1 22
nf f
T
1 2
1(minimum 1)
2f f tone spacing at n
T
Complex Envelope
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
103/114
A real bandpass waveform s(t) can be represented using complexnotation
Where g(t) is known as the complex envelope, expressed as:
The magnitude of the complex envelope is:
And its phase:
g(t) is called the baseband message or data in complex form and
, the carrier wave in complex form
})(Re{)(0tjw
etgts
)()()(|)(|)()()(
tjtjetRetgtjytxtg
)()(|)(|)( 22 tytxtgtR
)(
)(
tan)(1
tx
ty
t
tjwe 0
Then the modulation can be expressed as the product of the two
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
104/114
p p
Quadrature Implementation of a Modulator
Consider a baseband waveform g(t) appearing at discrete times k=1,2,, Then g(t), x(t) and y(t) can be written as gk, xk,yk. Let xk=yk=0.707A; Then complex envelope can be expressed in discrete form
as:
The modulation process suggests:
]}sin[cos)]()(Re{[)( 00 tjttjytxts
ttyttx00 sin)(cos)(
AjAjyxg kkk 707.0707.0
}Re{)( 0tjw
k egts ]}sin[cos]Re{[ 00 tjtjyx kk
tytx kk 00 sincos
tAtA 00 sin707.0cos707.0
4cos 0
tA
Quadrature Type Modulator
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
105/114
Lead/Lagrelationships
of sinusoids
Error Performance For Binary Systems
4 7 1 Probability of Bit error for coherently detected BPSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
106/114
4.7.1 Probability of Bit error for coherently detected BPSK
Whereas the received signal is :r(t) = si(t)+n(t)
The antipodal signals s1(t) and s2(t) can be characterized in a one-dimensional signal space as:
Decision is made on the basis:
Probability of bit error PB,
TttEts
tEts
0
)()(
)()(
22
11
otherwisets
Tzifts
)(
0)()(
2
01
0
21
)2/(
2
22exp
2
1
021
aaQduP
aaB
For equal-energy antipodal signaling the receiver output components are
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
107/114
For equal energy antipodal signaling, the receiver output components are
Then
2211 sforEaandsforEa bb
duPNE
Bb
0/2
2
2exp
2
1
0
2
N
EQP bB
Probability of Bit error for coherently detected Differentially
Encoded BPSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
108/114
Encoded BPSK
00
2
1
2
2 N
E
QN
E
QPbb
B
Fig 4.25
Probability of Bit error for coherently detected Binary
Orthogonal FSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
109/114
Orthogonal FSK
A general treatment for binary coherent signals (not limited to
antipodal signals) yields
For orthogonal, BFSK =/2; thus =0 and:
duPNE
Bb
0/)1(
2
2exp
2
1
duPNE
Bb
0/
2
2exp
2
1
0NEQP bB
Probability of Bit error for Noncoherently detected Binary
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
110/114
Orthogonal FSK
02exp2
1
N
E
Pb
B
Eb/N0 penalty of the simplernoncoherent detection is onlyabout 1dB at practical bit error
rates As a result, the simpler,
noncoherent FSK forms thebasis of many low end (e.g.1200 bps) telephone and radiomodems in the market-place
Note that, non-coherentperformance of FSK is notnearly as bad as that for ASK
Probability of Bit error for Binary DPSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
111/114
Theoretical performance forCOPSK and DPSK is shownhere for an AWGN channel
BER for COPSK is exactly thesame as that derived forbipolar (antipodal) basebandtransmission
0
exp2
1
N
EP bB
Advantages and Disadvantages of FSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
112/114
Advantages
FSK is a constant envelope modulation
hence insensitive to amplitude (gain) variations in the channel hence compatible with non-linear transmitter and receiver
systems
Detection of FSK can be based on relative frequency changesbetween symbol states and thus does not require absolute
frequency accuracy in the channel (FSK is thus relatively tolerant toLO drift and Doppler Shift)
Disadvantages
FSK is less bandwidth efficient than ASK or PSK The bit/symbol error rate performance of FSK is worse than PSK
In case of FSK, increasing the number of frequencies can increasethe occupied bandwidth
Advantages and Disadvantages of PSK
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
113/114
Advantage:
Bandwidth Efficiency
In order to improve on the bandwidth efficiency of bandpass datatransmission, we can increase the number of symbol states
A reduction in bandwidth by a factor of k
Mkk
BB
Binary
aryM 2_ log
b
aryM
b
BinarykT
BthenT
Bif1
,1
_
Disadvantages:
8/2/2019 Lec 9 DC_ Spring 2012_Bandpass Modulation
114/114
Reduced immunity to noise
As a general rule, we know that as the number ofsymbol states is increased, the tolerance to noise isreduced
Two exceptions to this rule, QPSK and orthogonalMFSK
Decreased immunity to noise compared to binary
Increased transmission power compared to binary
Increased complexity compared to binary Lower transmission quality compared to binary