LaserMax Optical Equipment & Accessories Operators Manual

RAIL MOUNTED LASER

Ruger SR22RAIL MOUNTED LASER

Operator’s Manual

LMS-RMSRRUGER SR22® | SR9C® | SR40C® | 9E®

12/14/15 5:16 PM

https://www.carid.com/lasermax/

L

R

PARTS IDENTIFICATION

adjustment tool

laser safety label

right activation switch

left activation switch

activation switch

screw opening

screw opening

windage port elevation port

lens

Right Housing

Left Housing

mounting screws 1/3N battery

RMSR User Guide 3.1.indd 1

IMPORTANT: Prior to installation, battery change, cleaning or maintenance, follow the firearm operator’s manual to ensure that the firearm is unloaded

INSTALLATION

1. To separate laser from its packaging, first rotate the disposable rail support upward to exposemounting screws. You may need to press the two small posts on rail support to release them from the tray (figure 1).

2. Use a Phillip’s screwdriver (not provided) to remove the two (2) mounting screws from left housing (figure 2). Set these screws aside.

3. Separate the left housing from the right housing.

4. Place right housing onto Picatinny rail as shown (figure 3).

5. Mate left housing with right housing, ensuring that activation switch passes through opening in left housing (figure 4).

6. Press together to remove gap (figure 5).

7. Insert two (2) mounting screws into recessed screw holes inleft housing.

1 2 3

4

!

Important: LMS-RMSR mounting screws are self-tapping; extra care should be taken when installing them for the first time to ensure that they are screwed in straight. Improper installation could cause the threads to strip.

8. Tighten mounting screws with a Phillips screwdriver (not provided). Do not over-tighten.

OPERATION1. To turn the laser on, press in on the activation switch from either side (figure 7). Press again

to turn the laser off.

2. To switch aiming point from pulse to steady, press and release the activation switch from either side to activate the laser. Then, press and hold the activation switch for 5 seconds. The laser mode will change. Repeat the process to return to the previous mode. Note: When reactivated, laser will always return to the previously set mode.

3. To save power and prevent inadvertent battery drain, the LMS-RMSR will shut off automatically after a ten minute period of inactivity. Cycle the activation switch to turn laser back on.

65

7

!

https://www.carid.com/optics.html

ALIGNING THE LASER1. Alignment adjustments should be made at a minimum of 10

yards distance from the target. To begin, insert adjustment tool into one of the two alignment ports (figures 8 & 9) and slowly rotate the tool while comparing laser position on target to fixed sights. The laser dot should be centered, slightly above top of front sight. Important: Do not rotate adjustment tool more than one full turn in either direction from the factory position – doing so may cause damage to the laser and void the warranty. A one quarter turn will result in a movement of approximately 3 inches at 10 yards.

2. Windage adjustment: with the muzzle pointing forward and adjustment tool inserted into the windage port, a clockwise turn will shift the laser aiming point to the left and a counterclockwise turn will shift the laser beam to the right (figure 8).

3. Elevation adjustment: with the muzzle pointing forward and adjustment tool inserted into the elevation port, a clockwise turn will shift the laser beam up and a counterclockwise turn will shift the laser beam down(figure 9).

4. Verify zero by shooting targets and making additional adjustments as needed.

Note: a slight shift in alignment may be observed after firing the first time. Recheckalignment after break in and readjust as necessary.

8

9

BATTERY REPLACEMENT TIP: During periods of non-use, test the LaserMax laser periodically to ensure adequate battery levels.

1. Remove mounting screws to separate left housing from right housing.

2. Lift expended 1/3N Lithium battery out of right housing.

3. Install a fresh 1/3N Lithium battery with the negative (-) side toward circuit board and positive (+) side against the coiled spring (figure 3).

4. Mate left housing with right housing, ensuring that activation switch passes through opening in left housing (figure 5). Press together to remove gap.

5. Insert two (2) mounting screws into recessed screw holes in left housing.

6. Tighten mounting screws with a Phillips screwdriver (not provided). Do not over-tighten.

CLEANING & MAINTENANCEAfter repeated fire, the lens may become clouded with gunpowder residue. For best results, it is recommended that this area be cleaned, along with the firearm, after each use. To clean the lens, follow these steps.

1. Keep firearm pointed in a safe direction.

2. Confirm laser is off.

3. Dampen the end of a cotton swab with isopropyl alcohol.

4. Apply dampened swab to lens and polish in a small circular pattern. Be sure to cleanaround edges of lens.

LaserMax components should never be submerged or flushed with cleaning solvents. Failure to adhere to these guidelines may cause damage and void the factory warranty.

T

12/14/15 5:16 PM

REPLACEMENT PARTS LMS-AT50 adjustment tool

LMS-13N replacement battery

LMS-2x13N 2-pack replacement batteries

CF-MS mounting screws

IF YOU EXPERIENCE AN ISSUE WITH YOUR LASER PLEASE DO NOT RETURN IT TO THE STORE.

REMINDER Aiming a laser beam at moving vehicles including boats, aircraft, trains, and construction equipment may be illegal. Check current applicable laws and follow them accordingly.

DANGER Laser radiation is emitted from the front aperture of the laser when

the switch is activated.

WARNING Avoid direct eye exposure to beam. Do not point laser at anything you do not wish to destroy.

NOTICE: The FDA requires the label supplied with your laser be affixed to the outside of the gun near the laser aperture.

LMS-RMSR Red Laser CLASS 3R VISIBLE LASER Output Power: <5mW Wavelength: 600–700nm

RAIL MOUNTED LASERS

MicroII


elevation port

activation switch

lens

battery hatch

battery hatch tab

windage port locking nut

REPLACEMENT PARTS LMS-AT50 adjustment tool



LMS-MICRO-CS clamping screw

adjustment tool

clamping screw 1/3N battery

IMPORTANT: PRIOR TO INSTALLATION, BATTERY CHANGE, CLEANING OR MAINTENANCE, FOLLOW THE FIREARM OPERATOR’S MANUAL TO ENSURE THAT THE FIREARM IS UNLOADED.

INSTALLATION1. To remove laser from package use a flat head screwdriver (not

supplied) to unscrew clamping screw from right side of laser housing.2. Position Micro II on firearm rail.3. Guide Micro II into position, aligning clamping screw hole with

preferred notch on rail (see figure 1).4. Insert clamping screw into right side of laser housing (see figure 2).

When fully inserted, clamping screw will engage locking nut. 5. Tighten clamping screw with a flat head screwdriver (not supplied). Note: Variations in depth of handgun rail notches may require thatclamping screw be pressed from locking nut end to remove.

OPERATING INSTRUCTIONS1. To turn the laser on, press and release the activation switch

from either side (see figure 3). Press and release again to turnthe laser off.

2. To switch the laser aiming point from pulse to steady, turn the laser on, then press and hold the activation switch for 3 seconds. Press and hold the activation switch for 3 seconds again to returnto the previous mode.

3. To save power and prevent inadvertant battery drain, Micro II will shut off automatically after a ten minute period of inactivity.Cycle the activation switch to turn the laser back on.

1

2

3

ALIGNING THE LASER1. Alignment adjustments should be made at a minimum of 10

yards distance from the target. To begin, insert the adjustmenttool into one of the two alignment ports (figures 4 & 5) and slowly rotate the tool while comparing the laser position on target to the fixed sights. Important: Do not turn alignment screws more than one full turn in either direction from their factory position. This may cause damage to the laser and void the warranty. A one quarter turn will result in a movement of about 7 inches at 10 yards.

2. Windage adjustment: with the muzzle pointing forward and adjustment tool inserted into the alignment port on the right side, a clockwise turn will shift the laser aiming point to the left and a counterclockwise turn will shift the laser beam to the right.

3. Elevation adjustment: with the muzzle pointing forward and adjustment tool inserted into the alignment port on the bottom, a clockwise turn will shift the laser beam down and a counterclockwise turn will shift the laser beam up.

Note: a slight shift in alignment may be observed after firing Micro II for the first time. Recheck alignment after break in and readjust as necessary.

BATTERY REPLACEMENTMicro II can remain on the firearm or be removed to change the battery.


2. Press and hold battery hatch near tab (see figure 6).

4

5

6

While maintaining pressure on battery hatch with one hand, use the other hand to press battery hatch tab away from battery hatch (see figure 7).

3. Release battery hatch to expose battery chamber.

4. Replace expended battery with fresh 1/3N battery. The flat, inscribed side of battery should face outward (see figure 8).

5. Secure battery hatch by applying gentle pressure until it snaps closed.

CLEANINGAfter repeated fire, the lens may become clouded with gunpowder residue. For best results, it is recommended that this area be cleaned, along with the firearm, after each use. To clean the lens, follow these steps:




4. Apply dampened swab to lens and polish in a small circular pattern. Be sure to clean around edges of lens.

WARNINGCare should be taken when applying oil or lubricant to clean the firearm. Getting oil or lubricant on the laser components may cause damage and void the factory warranty. The Micro II should not be submerged or flushed with cleaning solvents.

8

7

IF YOU EXPERIENCE AN ISSUE WITH YOUR MICRO II LASER, PLEASE DO NOT RETURN IT TO THE STORE.

MICRO-2-R Red Laser CLASS 3R VISIBLE LASER Output Power: <5mW Wavelength: 650nm

MICRO-2-G Green Laser CLASS 3R VISIBLE LASER Output Power: <5mW Wavelength: 510-535nm

MICRO-2-IR Infrared Laser CLASS 1 LASER Output Power: <0.7mW Wavelength: 850nm


DANGER Laser radiation is emitted from the front aperture of the laser when the switch is activated.


ITAR CONTROLLEDCLASS 1 LASER PRODUCT

<0.7mWWavelength: 850nm

COMPLIES WITH 21CFR1040 PER LASER NOTICE 50 (2007)

ADJUSTABLE FIT LASER

· Advanced mounting technology provides the perfect fit

· Accessory rail permits attachment of tactical light

· Aiming point can be set to operator’s choice of pulse or steady

· Auto-off after 10 minutes preserves battery power

Operator’s Manual

9/30/15 11:18 AM

SPARTAN


adjustment tool

laser safety label

paddle switch

screw openings

windage port elevation port

rail vise positioner

lens

Right Housing

Left Housing

clamping screws 1/3N battery

Spartan User Guide.indd 1

IMPORTANT: PRIOR TO INSTALLATION, BATTERY CHANGE, CLEANING OR MAINTENANCE, FOLLOW THE FIREARM MANUFACTURER’S INSTRUCTIONS TO ENSURE THAT THE FIREARM IS UNLOADED.

INSTALLATION1. To separate Spartan™ from

its packaging, first rotate the disposable rail support upward to expose clampingscrews. You may need to press the two small posts on rail support to release them from the tray (figure 1).

2. Use a Phillip’s head screwdriver (not provided) to remove the two (2) clamping screws from left housing (figure 2). Set thesescrews aside.

3. Separate the left and right laser housings. Remove rail vise positioner (figure 3) and set it aside.

4. Identify the right housing and take note of its slotted channels(figure 4).

5. Position the right housing against the rail of the firearm as shown (figure 5). Hold in place on rail at the desired location between trigger guard and muzzle.

SPARTAN

1 2

3 4

5

6. Slide the curved front end of rail vise positioner into the Picatinny rail slot and position thethree teeth into the corresponding slotted channels in right housing (figure 6). Note: While holding this assembly in place with your support hand, assume a normal grip on the firearm and test the trigger finger’s reach to the paddle switch to ensure optimal placement on the rail. To customize the fit, remove right housing, reposition as desired, then place the slotted channels of right housing back onto the teeth of rail vise positioner in its new, preferred location.

7. Mate left laser housing with right housing and press the two halves together to close the gap.

8. While holding the completed assembly in place on the pistol rail, insert two (2) clamping screws into the holes inthe left housing (figure 7).

9. Partially tighten clamping screws with a Phillip’s head screwdriver (not provided). Ensure that the laser is attached at the desired point on the rail before completely tightening the screws. Do not overtighten.

OPERATING INSTRUCTIONS1. To turn the laser on, press and release the paddle switch from either side. Press and release

again to turn the laser off.

2. To switch the laser aiming point from pulse to steady, turn the laser on, then press and hold the paddle switch for 5 seconds. Press and hold the paddle switch again to return to theprevious mode.

3. To save power and prevent inadvertent battery drain, Spartan™ will turn off automaticallyafter a ten minute period of inactivity. Cycle the paddle switch to turn the laser back on.

6

7

ALIGNING THE LASER1. Alignment adjustments should be made at a minimum

of 10 yards distance from the target. To begin, insert the adjustment tool into one of the two alignment ports (figures8 & 9) and slowly rotate the tool while comparing the laser position on target to the fixed sights. Important: Do not turnalignment screws more than one full turn in either direction from their factory position. This may cause damage to the laser and void the warranty. A one quarter turn will result ina movement of about 7 inches at 10 yards.

2. Windage adjustment: with the muzzle pointing forward andthe adjustment tool inserted into the alignment port on the right side, a clockwise turn will shift the laser aiming point to the right and a counterclockwise turn will shift the laser beam to the left.

3. Elevation adjustment: with the muzzle pointing forward and the adjustment tool inserted into the alignment port on the bottom, a clockwise turn will shift the laser beam down and a counterclockwise turn will shift the laser beam up.

Note: a slight shift in alignment may be observed after firing Spartan™ for the first time. Recheck alignment after break in and readjust as necessary.

BATTERY REPLACEMENTSpartan™ can remain on the firearm or be removed to change batteries. Follow these steps:

1. Use a Phillips head screwdriver to remove clamping screws from left housing.2. Remove left housing to expose the battery compartment.

SPARTAN

8

9

3. Carefully remove the expended 1/3N battery (see figure 10).

4. Insert a fresh 1/3N battery with the negative (–) side facing thegold contact.

5. Mate left housing with right housing and press the two halves together to close the gap.

6. While holding the assembly in place on the pistol rail, insert two (2) clamping screws into the holes in left housing.

7. Partially tighten the screws with a Phillips screwdriver.

8. Ensure that the laser is attached at desired point on rail before completely tightening the screws. Do not over-tighten.

CLEANINGAfter repeated fire, the lens may become clouded with gunpowder residue. For best results, it is recommended that this area be cleaned along with the firearm after each use. To clean the lens, follow these steps:




4. Apply dampened swab to lens and polish in a small circular pattern. Be sure to clean around the edges of the lens.

WARNINGCare should be taken when applying oil or lubricant to clean the firearm. Getting oil or lubricant on laser components may cause damage and void the factory warranty. Spartan™ should not be submerged in or flushed with lubricants or cleaning solvents.

10

9/30/15 11:18 AM

REPLACEMENT PARTS 06049-0-1 rail vise positioner

LMS-AT50 adjustment tool



CF-MS clamping screws

IF YOU EXPERIENCE AN ISSUE WITH YOUR SPARTAN™ LASER PLEASE DO NOT RETURN IT TO THE STORE.

SPS-R Red Laser CLASS 3R VISIBLE LASER Output Power: <5mW Wavelength: 650nm

SPS-G Green Laser CLASS 3R VISIBLE LASER Output Power: <5mW Wavelength: 510-535nm


DANGER Laser radiation is emitted from the front aperture of the laser when

the switch is activated.


NOTICE: The FDA requires the label supplied with your laser be affixed to the outside of the gun near the laser aperture.

RAIL MOUNTED LASERS

Uni™

RAIL MOUNTED LASERS

Uni

LMS-UNI-ESLMS-UNI-GLMS-UNI-IRLMS-UNI-ES-RVPLMS-UNI-GVPLMS-UN-IR-RVP

LMS-UNI-ES | LMS-UNI-G | LMS-UNI-IR


lens

removable rail grip

battery cover screws

adjustment tool

1/3N batteries

357 batteries

LMS-UNI-ES | LMS-UNI-IR

LMS-UNI-G

clamping screw

integrated rail

activation switch

battery cover

battery cover

IMPORTANT: Prior to installation, battery change, cleaning or maintenance, follow the firearm operator’s manual to ensure that the firearm is unloaded.

INSTALLATION ON PISTOL RAIL1. To separate UNI from its packaging, first rotate the

disposable rail support upward to expose clamping screw. You may need to press the two small posts on rail support to release them from the tray (figure 1).

2. Loosen clamping screw with a coin or flat head screwdriver (not provided). Do not remove clamping screw.

3. While gripping UNI housing, press in on clamping screw to expand opening of removable rail grip (figure 2) and remove from disposable rail support packaging.

4. Mount UNI on firearm rail as shown (figure 3), then release pressure on clamping screw. Ensure that UNI is securely positioned on rail surface and clamping screw is seated into rail notch.

5. Tighten clamping screw with a coin or flat head screwdriver.

6. Additional accessories may now be mounted to UNI’s integrated rail following the accessory manufacturer’s instructions.

1

2

3

!

OPERATION1. To turn laser on, press in on activation switch from either side

(figure 4). Return switch to center position to turn laser off.

2. To switch laser aiming point from pulse to steady, turn laser on for at least two seconds, then turn it off. Next, cycle laser on and off three times from the same side, stopping at the center position between each cycle (each on/off cycle should take less than half of a second). To return the laser to the previous mode, repeat the process.

3. To save power and prevent inadvertent battery drain, UNI will shut off automatically after a ten minute period of inactivity. Cycle the activation switch to turn laser back on.

ALIGNING THE LASER1. Alignment adjustments should be made at a minimum of 10 yards distance from the target.

To begin, insert adjustment tool into one of the two alignment ports (figures 5 & 6) and slowly rotate the tool while comparing laser position on target to fixed sights. Important: Do not turn alignment screws more than one full turn in either direction from the factory position. This may cause damage to the laser and void the warranty. A one quarter turn will result in a movement of about 3 inches at 10 yards.

2. Windage adjustment: with the muzzle pointing forward and adjustment tool inserted into windage port, a clockwise turn will shift the laser aiming point to the left and a counterclockwise turn will shift it to the right (figure 5).

3. Elevation adjustment: with the muzzle pointing forward and adjustment tool inserted into elevation port, a clockwise turn will shift the laser aiming point down and a

4

counterclockwise turn will shift it up (figure 6).

Note: a slight shift in alignment may be observed after firing the first time. Recheck alignment after break-in and readjust as necessary.

BATTERY REPLACEMENT

1. Loosen both battery cover screws with a Philips head screwdriver to remove battery cover.

2. Turn UNI over to eject expended batteries.

3. Insert fresh batteries as shown (figure 7).

4. Reinsert battery cover by sliding edge of battery cover into battery cover slot (figure 8).

5. Reinstall battery cover screws to secure battery cover. Do not overtighten.

87 battery cover slot

5 6

REPLACEMENT PARTS 04520-3-3 battery cover (UNI-ES & UNI-IR)LMS-UNI-BCN-G battery cover (UNI-G) LMS-UBCS battery cover screwsLMS–2X357 (2) 357 batteries (UNI-ES & UNI-IR)LMS–2X13N (2) 1/3N batteries (UNI-G)LMS-AT50 adjustment tool LMS–UNI–CS clamping screw with springLMS–UNI–RG removable rail gripLMS–UNI–AS activation switch04507-0-1 activation switch coverLMS-SCS activation switch cover screwsLMS-UNI-MAS- 6 momentary switch 6” cordLMS-UNI-MAS-10 momentary switch 10” cordLMS-MANTA manta rail cover system

CLEANINGAfter repeated fire, the lens may become clouded with gunpowder residue. For best results, it is recommended that this area be cleaned, along with the firearm, after each use. To clean the lens, follow these steps:




4. Apply dampened swab to lens and polish in a small circular pattern. Be sure to clean around edges of lens.

LMS-UNI-ES-RVP | LMS-UNI-GVP | LMS-UNI-IR-RVP

RIFLE PACK PARTS IDENTIFICATION

cord cover

pressure pad

momentary activation switch (MAS)

sleeve

activation switch cover screws

activation switch cover

end cap

end cap

connector

cord

lubricant

lens

removable rail grip

battery cover screwsadjustment tool 1/3N batteries

357 batteries

clamping screw

integrated rail

activation switch

LMS-UNI-ES | LMS-UNI-IR

LMS-UNI-G

battery cover

battery cover

INSTALLATION OF MOMENTARY ACTIVATION SWITCH (MAS)All UNI lasers leave the factory configured for use with the standard activation switch. To change to the rifle (MAS) configuration, follow these steps:

1. Loosen battery cover screws with a Philips head screwdriver (not provided). Do not remove.

2. Remove activation switch cover screws (figure 9) and set aside.

3. Carefully remove activation switch cover and activation switch. Store these parts for future use (figure 10).

4. Insert connector of momentary activation switch into opening in UNI as shown (figure 11).

5. Reinstall activation switch cover screws to secure connector. Do not overtighten.

6. Tighten battery cover screws. Do not overtighten.

7. Shift the UNI master ON/OFF switch toward the cable to activate the pressure pad of the momentary activation switch (figure 12). Verify connection by pressing the pressure pad. The UNI laser aiming point will now illuminate whenever the pressure pad is pressed.

Tip: Slide Uni master ON/OFF switch to the “OFF” position during transport or when not is use to prevent inadvertant activation.

9

10

11

12

T

INSTALLATION ON RIFLE RAIL

1. To install on rifle rail, first, loosen clamping screw with a coin or flat head screwdriver (not provided). Do not remove clamping screw.

2. While gripping UNI housing, press in on clamping screw to enlarge removable rail grip opening (figure 13).

3. Mount UNI on firearm rail as shown (figure 14), then release pressure on clamping screw. Ensure that UNI is securely positioned on rail surface and clamping screw is seated into rail notch.

4. Tighten clamping screw with a coin or flat head screwdriver.

5. Additional accessories may now be mounted to UNI’s integrated rail following the accessory manufacturer’s instructions.

INSTALLATION OF MANTA® CORD MANAGEMENT SYSTEM1. Insert pressure pad through front of Manta® end cap

(figure 15 ).

13 14

15

2. Coat pressure pad with a small amount of lubricant to aid in installation.

3. Slide lubricated pressure pad into Manta® sleeve as shown (figure 16)

4. Position assembled momentary activation switch at desired location on firearm, angling to hook edge of Manta® sleeve on firearm rail (figure 17).

5. Snap opposing edge of Manta® sleeve onto firearm rail to secure.6. Attach remaining Manta® end cap on opposite side of Manta® sleeve (figure 18).

7. Adjust Manta® end caps to achieve desired placement.

8. Snap supplied Manta® cord cover over cord to ensure snag-free operation (figure 19).

16 17

18 19

IF YOU EXPERIENCE AN ISSUE WITH YOUR UNI LASER, PLEASE DO NOT RETURN IT TO THE STORE.

LMS-UNI-ESLMS-UNI-ES-RVPRed Laser CLASS 3R VISIBLE LASER Output Power: <5mW Wavelength: 600–700nm

LMS-UNI-GLMS-UNI-GVP Green Laser CLASS 3R VISIBLE LASER Output Power: <5mW Wavelength: 510-535nm

LMS-UNI-IRLMS-UNI-IR-RVP Infrared Laser CLASS 1 LASER Output Power: <0.7mW Wavelength: 800–900nm


DANGER Laser radiation is emitted from the front aperture of the laser when the switch is activated.


ITAR CONTROLLEDCLASS 1 LASER PRODUCT

<0.7mWWavelength: 800–900 nm

COMPLIES WITH 21CFR1040 PER LASER NOTICE 50 (2007)

Documents

LaserMax Optical Equipment & Accessories Operators Manual