Embed Size (px)
Citation preview
ANCHORING GROUT | ENGLISH VERSION 02/20201 |
Fluidity Non-Shrink
High CompressiveStrength
Anchoring TrowelStrength
Mixing
Plasticconsistency
Pouringconsistency
1 bag 25 kg.
Water (Litres)
2.5
3.6
12.5 Litres
13 Litres
Workable mortar
ANCHORING GROUT
A premixed cementitious non-shrink grout.
CHARACTERISTICS
DESCRIPTION
USES
WORK INSTRUCTIONS
DOSAGE
PACKAGING
• 25 kg. bag.
• 1 year from date of manufactureif stored in unopened originalpackaging in dry condition.
STORAGE
• High compressive strength up to 700 KSC.
• Impact and vibration resistance.
• Fuidity.
• No bleeding.
• No shrinkage.
• No crack.
• Anchoring rebar and bolt in concrete.
• Horizontal and vertical application.
Surface Preparation
1. The substrate must be clean, no dust and without any traces of oil,
laitance or curing compound.
2. The steel rebar must be cleaned, no rust and oil.
3. Remove loose and damaged concrete and laitance using
a point tool or chisel in order to obtain a clean surface.
4. Damp the substrate prior to application.
NON-SHRINK GROUTRepairingand Grouting
e-learning VDO*The information provided in this document results from our knowledge of the products and our experience. On-site results may vary, in particular according to the product application methods adopted. Where application methods not representative test before using the products. The above-mentioned information in no way constitutes a warranty relative to the use of the products. Our general terms and conditions of sale shall prevail, in any event, on the information provided in this document. Prior to application, customers and users are requested to check that they have the lasted version of this document.
Sika (Thailand) Limited700/ 37 Moo 5, Amata City Chonburi Industrial Estate, Km.57 Bangna-Trad Rd, Klong Tamhru, Muang, Chonburi 20000
e-learning VDO*The information provided in this document results from our knowledge of the products and our experience. On-site results may vary, in particular according to the product application methods adopted. Where application methods not representative test before using the products. The above-mentioned information in no way constitutes a warranty relative to the use of the products. Our general terms and conditions of sale shall prevail, in any event, on the information provided in this document. Prior to application, customers and users are requested to check that they have the lasted version of this document.
Sika (Thailand) Limited700/ 37 Moo 5, Amata City Chonburi Industrial Estate, Km.57 Bangna-Trad Rd, Klong Tamhru, Muang, Chonburi 20000
ANCHORING GROUT | ENGLISH VERSION 02/20202 |
Flexural Strength ASTM C348 (Pouring) (MPa) Evaluation
3 Days > 5
7 Days > 7
28 Days > 8Compressive Strength ASTM C109 (Pouring) (MPa) Evaluation
Compressive Strength ASTM C109 (Plastic) (MPa) Evaluation
Shrinkage ASTM C1090
Specimens of Cementitious Mixtures ASTM 827 : 0-4%
Evaluation
1 Day > 20
3 Days > 40
7 Days > 50
28 Days > 60
1 Day > 40
3 Days > 55
7 Days > 65
28 Days > 70
1 Day 0- +0.3%
3 Days 0- +0.3%
14 days 0- +0.3%
28 Days 0- +0.3%
Particle Size, max. : 2 mm.
Bulk Density (kg./L.) : 1.31 +/- 0.1
Pot Life (min.) : 30
Initial setting (min.) :
Final setting (min.) :
325
360
Product Preparation
1. Mix LANKO 703 ANCHORING GROUT with clean water.
Mixing at least 3 minutes or until required consistency
is obtained.
2. Leave the mixture to stand for 1-3 minutes.
1. Formwork should be at least 50 mm. from the plate and
25 mm. above the bottom of the plate.
2. Pour a continuous flow of grout from one side only.
3. When mortar begins to set, cure with curing compound
(e.g. LANKO 361 CURE).
AnchoringApplication
Grouting and bedding
1. Diameter of the holes : diameter of the rebar +20 to
30 mm.
2. Maximum thickness between concrete and rebar should
not exceed 50 mm.
3. Depth of hole : 10-20 times of diameter of rebar.
4. Remove residual water prior to anchoring.
PRECAUTIONS
• Temperature range for use : 5Oc to 35Oc.
• Do not use a concrete vibrator.
• Do not mix with other product.
SPECIFICATIONS
