Upload
vubao
View
215
Download
0
Embed Size (px)
Citation preview
Oct 14th – 16th 2015, Brno, Czech Republic, EU
Feb 20th 2015
TEMPLATE FOR PAPER / POSTER PREPARATION
Obligatory division of the paper:
Abstract Keywords Introduction Main text (containing the methodological bases, experimental part, results and its discussion), Conclusion AcknowledgementsReferences
Text editor: MS WORD version 97 and newer
Font: size 10 pt, ArialSpacing: 1.2Margin of the page: 20 mm from all sides
TITLE OF PAPER (11 pt, bold, center, gaps 12 before, 6 after, spacing 1.2)
Authors (SURNAME Name) (11 pt, center, gaps 12 and 12, spacing 1.2)e.g. NOVÁK Jan1, ALTMAN John2
Name and address of the institution, e-mail address (10 pt, italics, center, gaps 6 and 0, spacing 1.2)e.g. 1VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
2University of Strathclyde, Faculty of Physics, Glasgow, Scotland, United Kingdom, EU
Abstract (title 10 pt, bold, gaps 24 and 0)
Abstracts (text 10 pt, gaps 6 and 0) must have extent to 250 words.
Keywords: (title10 pt, bold, gaps 6 and 0, text: max 5 keywords, 10 pt, gaps 6 and 0)
1. CHAPTER TITLES (10 pt, bold, gaps 18 and 0)
We recommend split the text of paper (gaps 6 and 0) into numbered chapters and subchapters, for example 1.1, 1.2 etc. Please use the specific header and footer in written paper. For sending your paper, use the conference registration system please. The range of papers is up to 6 pages incl. pictures and 20 MB.
The paper must be sent in *.doc, *.docx or *.rtf format.
1.1. Subchapter title (10 pt, bold, gaps 12 and 0)
Oct 14th – 16th 2015, Brno, Czech Republic, EU
2. PICTURES, EQUATIONS, TABLES
It is recommended to put tables and pictures within the text. The name of the table (Table 1 Real, minimal and maximal chemical) write above the table to the left (10 pt, bold) and the name of the picture (Fig. 1 Volume enthalpy) write under the picture to left or center (10 pt, bold). The text of table or picture is 10 pt.
It is possible to include the color pictures and graphs into the text, because the proceedings will be in the electronic form. The pictures have to be original or quality scanned. We will not accept bad photocopy. Descriptions of the pictures should be clear and legible. The pictures and graphs must be a part of paper. If you have any questions, please write to the conference secretariat.
The position of the figures (in the figure position “Tab”) should be selected as the "In the text"
Fig. 1 Title of the figure (10 pt, gaps 6 and 12)
Table 1 Title of table (10 pt, gaps 12 and 2)
Text (9 pt, gaps 6 and 0, single spacing) Column
Row
Equations must be created in Equation Editor and written in the separate line on the left side for example:
(1)
We ask you to keep writing repeating units and captions by these examples
700 MPa; 100 g; 900 °C; 1040 K; 0.5 % (fundamentally decimal point, not comma); 1.5 h;
W = 2000 mm; ld /h0 > 3; v = 600 ms-1 (mathematical dot in the middle row, insert not using the equation, but as a symbol); 52 x 10-5; W/(mK); it is also accepted W/mK; 20 °C to 80 °C; 180 °C; description of axes at the Figs: Surface temperature (°C)
3. CONCLUSION
The paper must contain conclusion.
Oct 14th – 16th 2015, Brno, Czech Republic, EU
ACKNOWLEDGEMENTS
The acknowledgements, please, write size 10 pt, italics, bold and center it.
REFERENCES
The number of cited references can be written in square brackets placed immediately after the text and continuously. Do not start on a new page. References to the literature mark in by the Arabic numerals continuously in order as they appear in the text. The font size in the References is 9 pt, right align. Examples are shown for: [1] - a book, [2] - article in a journal, [3] - paper in the proceedings:
[1] CAMPUZANO F., MULA J. Supply Chain Simulation: A System Dynamics Approach for Improving Performance. Springer: London, 2011.
[2] CHRISTOPHER M., PECK H. Building the Resilient Supply Chain. International Journal of Logistics Management, Vol. 15, No. 2, 2004, pp. 1-13.
[3] WICHER P., LENORT R. Inventory Planning and Control of Electrodes for Electric Arc Furnace. In METAL 2013: 22nd International Conference on Metallurgy and Materials. Ostrava: TANGER, 2013, pp. 2050-2056.
NOTE: LIST OF ERRORS THAT AUTHORS MAKE OFTEN
Scientific goal and contribution of the paper is not clearly defined in the introduction of the paper
Absence of citations of the tables and figures in the text with relevant commentary
Missing bibliographic references in the text
Absence of the conclusion
Lack of sufficient number of citations to the current foreign literature, especially journals
Wrong format of cited references