John Deere Spraying Solutions · PDF fileJohn Deere Spraying Solutions ... When you’re in the market for spray nozzles and accessories, ... The American Society of Agricultural and

John Deere Spraying SolutionsSpray Nozzles and Accessories Guide

Technozzlegy[tek-noz’-uhl-jee]

John Deere Spraying Solutions

John Deere is redefining sprayer performance and accuracy. A concept so advanced, we’re calling it Technozzlegy, the next generation in a long line of John Deere nozzles, pumps and accessories. A total performance package that will unleash the full potential of your sprayer for every application-fertilizer, herbicides, fungicides and insecticides. It’s never been easier to choose the right spray nozzle to match each application.

When you’re in the market for spray nozzles and accessories, you’ll find this booklet to be a helpful tool in determining the correct tip for your particular spraying situation. Your local John Deere dealer is also a valuable resource for any of your spraying application questions.

Application type .....................................................2Spray Nozzle Information .......................................6Wear and Chemical Compatibility .........................10Spray Heights .......................................................12Ultra Low-drift (ULA) ............................................14Ultra Plus Low-drift (ULAC) ...................................16TwinAir (TAQ) .......................................................18Low-drift Air (LDA) ................................................20GuardianTM (LDX) ..................................................22Low-drift (LD) .......................................................24Low-drift Ceramic (LDC) .......................................26Extended Range (ER) ............................................28Extended Range Stainless Steel (ERI) ....................30Extended Range Ceramic (ERC) .............................32Flat Fan (FF)..........................................................34High Flow (HF) ......................................................36

Flood (FL) .............................................................38Straight Stream Ceramic (STC) ..............................40Straight Stream (ST) .............................................42Hollow Cone Ceramic (HCC) ..................................44Even Spray (ES) .....................................................46Chemical Resistant (CR) ........................................48Off-Center Brass (OC) ...........................................50Fence Row/Boomless (XT) ....................................52TwinCapTM ............................................................54Nozzle Body Adapters ...........................................55 Spray Nozzle Caps ................................................56Plumbing products ...............................................58Pumps ..................................................................59Application support ..............................................60Liquid-handling ....................................................61

JOHN DEERE SPRAY PARTS Table of Contents

1

JOHN DEERE SPRAY PARTS

2

Application type

The following chart has been designed to simplify selection of the correct spray tip type for the agrochemical to be applied. It is based on having good conditions for spraying and should be used in conjunction with the agrochemical manufacturer’s label.

Manufacturer's Recommended droplet size

John Deere Spray Nozzle Selection Guide

Sect

ion

Code Spray Tip Orifice Material Pressure RangeNominal Spray

Angle Pattern VF F M C VC XC

Broa

dcas

t

ULA Ultra Low-drift Polyacetal 15 to 115 120 Tapered FanULAC Ultra Plus Low-drift ceramic Ceramic 30 to 100 110 Tapered FanTAQ TwinAir Polyacetal 30 to 115 110 Twin Tapered FanLDA Low-drift Air Polyacetal 15 to 115 110 Tapered FanLDX Guardian™ Polyacetal 15 to 115 120 Tapered FanLD Low-drift Polyacetal 15 to 70 110 Tapered FanLDC Low-drift Ceramic Ceramic 30 to 70 110 Tapered FanER Extended Range Polyacetal 15 to 70 80,110 Tapered FanERC Extended Range Ceramic Ceramic 20 to 70 110 Tapered FanERI Extended Range Stainless Steel Stainless Steel 15 to 70 80 Tapered FanFF Flat Fan Polyacetal 30 to 60 80,110 Tapered Fan

3


John Deere Spray Nozzle Selection Guide

Application type

Sect

ion



Broa

dcas

t

ULA Ultra Low-drift Polyacetal 15 to 115 120 Tapered FanULAC Ultra Plus Low-drift ceramic Ceramic 30 to 100 110 Tapered FanTAQ TwinAir Polyacetal 30 to 115 110 Twin Tapered FanLDA Low-drift Air Polyacetal 15 to 115 110 Tapered FanLDX Guardian™ Polyacetal 15 to 115 120 Tapered FanLD Low-drift Polyacetal 15 to 70 110 Tapered FanLDC Low-drift Ceramic Ceramic 30 to 70 110 Tapered FanER Extended Range Polyacetal 15 to 70 80,110 Tapered FanERC Extended Range Ceramic Ceramic 20 to 70 110 Tapered FanERI Extended Range Stainless Steel Stainless Steel 15 to 70 80 Tapered FanFF Flat Fan Polyacetal 30 to 60 80,110 Tapered Fan

Color Code ClassificationVF Very FineF FineM MediumC Coarse

VC Very CoarseXC Extremely Coarse

* See product page for complete listing.


4

Application type

Sect

ion



Wid

e HF High-Flow Polyacetal 20 to 80 140 Wide-angle Tapered FanFL Flood Polyacetal 15 to 60 80 to 145 Wide-angle Flood

Stre

am

STC Straight Stream Ceramic Ceramic 15 to 60 0 6-stream SST Straight Stream PVDF 15 to 150 0 Stream SD-C Disc and Core Polyacetal 10 to 150 0 Stream S

Band

ing

& Di

rect

ed D-C Disc and Core Polyacetal 10 to 150 45 to 110 Hollow ConeHCC Hollow Cone Ceramic Ceramic 40 to 350 80 Hollow ConeES Even Spray Polyacetal 30 to 60 80 Even FanOC Off-Center Brass 30 to 60 80 Off-center Tapered Fan

Spec

ial XT Fence row/boomless Polyacetal or

Stainless Steel 30 to 60 105 Ultra-wide Boomless Fan

TC TwinCap™ Polyacetal or PVDF --- --- Double Tip HolderCR Chemical Resistant PVDF 110 Tapered Fan

5

JOHN DEERE SPRAY PARTSApplication type

Sect

ion



Wid

e HF High-Flow Polyacetal 20 to 80 140 Wide-angle Tapered FanFL Flood Polyacetal 15 to 60 80 to 145 Wide-angle Flood

Stre

am

STC Straight Stream Ceramic Ceramic 15 to 60 0 6-stream SST Straight Stream PVDF 15 to 150 0 Stream SD-C Disc and Core Polyacetal 10 to 150 0 Stream S

Band

ing

& Di

rect

ed D-C Disc and Core Polyacetal 10 to 150 45 to 110 Hollow ConeHCC Hollow Cone Ceramic Ceramic 40 to 350 80 Hollow ConeES Even Spray Polyacetal 30 to 60 80 Even FanOC Off-Center Brass 30 to 60 80 Off-center Tapered Fan

Spec

ial XT Fence row/boomless Polyacetal or

Stainless Steel 30 to 60 105 Ultra-wide Boomless Fan

TC TwinCap™ Polyacetal or PVDF --- --- Double Tip HolderCR Chemical Resistant PVDF 110 Tapered Fan

S These nozzles produce streams to minimize atomization.


6

Spray nozzle information

ASABE S572 Droplet Size Classification

The American Society of Agricultural and Biological Engineers (ASABE) developed the ASABE S572 standard to measure and interpret spray quality from tips.

Spray Quality* Size of Droplets Retention on Difficult to Wet Leaves Used for Drift Potential

Very Fine Small Excellent Exceptions High

Fine Very Good Good Cover

Medium Good Most Products

Coarse Moderate Systemic Herbicides

Very Coarse Poor Soil Herbicides

Extremely Coarse Large Very Poor Liquid Fertilizer Low

*Always read the pesticide label to determine which spray quality is required.

7

JOHN DEERE SPRAY PARTSSpray nozzle information

The ASABE S572 standard uses six droplet classification categories, six of which are common for agriculture and horticulture:

Very Fine , Fine , Medium , Coarse , Very Coarse and Extremely Coarse .

Most agrochemical applications recommend a fine, medium, or coarse spray.

Fine sprays provide enhanced retention for directed spraying on the target including:

•Foliar-acting weed control

•Contact-acting fungicides and insecticides

Medium sprays are the most widely used spray type.

•Used by default by most applicators when spray quality is not defined by the label.

•Systemic-acting fungicides, insecticides and herbicides

Coarse sprays are used with systemic, residual, and soil-applied herbicides.


8

Suggested minimum spray heights — Flat fan spray nozzles

Droplet sizes are expressed in microns. One micron equals .001 millimeters. Other than the effects of the specific material being sprayed, the four major factors affecting droplet size are:

• Spraynozzlestyle—flatfan,floods,cones,discs,cores• Capacity—lowflowproducessmallerdroplets;highflowproduces

larger droplets• Pressure—lowpressureproduceslargerdroplets;highpressureproducessmallerdroplets• Spraypatterntype—eliptical(flatfannozzle),band(banded/floodnozzle),conical(cone

nozzle)

ThresholdsClassificationcategory Symbol Dv0.1 Dv0.5 Dv0.9

Droplet size classification is based on BCPC specification and in accordance with ASAE S-572 at date of printing 10/04. Classifications are subject to change.Measures made by MALVERN particle size 2600 and Oxford Visisizer.

Very fine 41.5 99.9 170.8Fine 65.7 163.6 350.1Medium 88.0 249.4 495.2Coarse 95.6 365.1 683.5Very coarse 109.2 408.3 842.6Extremely coarse 109.2 >408.3 >842.6

9



10

Wear and Chemical Compatibility

Comparative Accelerated Wear Test

Time (Hours)

% In

crea

sein

Flo

w

Brass 26% (worst)Stainless Steel 15% (fair)PVDF 12% (good)Polyacetal 8% (better)Ceramic 5% (best)

Comparative Accelerated Wear Test

Time (Hours)

% In

crea

sein

Flo

w

Brass 26% (worst)Stainless Steel 15% (fair)PVDF 12% (good)Polyacetal 8% (better)Ceramic 5% (best)

11

JOHN DEERE SPRAY PARTSWear and Chemical Compatibility

CERAMIC (C) — Highly resistant to abrasive and corrosive chemistry, and pro vides superior wear resistance in abrasive applications and high pressures. Nozzle orifices are made of pink sintered ceramic and reinforced by special oxides.

POLYACETAL (P) — Provides good resistance to most chemicals and superior resistance to wear with most agricultural chemistry. Susceptible to strong mineral acids and a few organic solvents. Resistance to most alkalis is excellent. Organic solvents usually cause slight swelling without any other harmful effect.

POLYVINLYIDENE FLUORIDE (PVDF) — Should be used with acid-based agricultural defoliation chemistry. Good resistance to wear. Resists many reagents and high temperatures (up to 300º F , 148º C). Susceptible to high temper-atures above water boiling (210º F , 98º C) in combination with concentrated sulfuric and nitric acids. Preferred in industrial spraying applications.

STAINLESS STEEL (SS) — Good resistance to chemicals and average wear resistance.

BRASS (B) — Average resistance to most chemistry and poor wear resistance. Susceptible to corrosion, especially with fertilizers.


12

Spray Heights

Suggested Minimum Broadcast Spray Heights (Flat Fan Spray Tips)

(ERI)

(ULA)

(ERI)

(ULA)

13


Suggested Minimum Broadcast Spray Heights (Flat Fan Spray Tips)

Spray Heights

(ERI)

(ULA)

(ERI)

(ULA)

Optimum Broadcast Spray Heights(Flat Fan Spray Tips)

* Not Recommended** 40” tip spacing is prone to off-target trespass under certain conditions that affect drift.


14

Ultra Low-drift Air (ULA)

ULTRA low drift — The ULA nozzle with dual air-eduction technology produces large air-filled droplets, optimizing drift control and target coverage. The wide 120-degree spray angle enables the boom height to be lowered to further reduce drift. The UL is ideal for use with pre-emergence and broad-spectrum systemic products. Unlike other air-aspirated nozzles, the UL is precision molded completely out of polyacetal. Independent tests show that polyacetal wears up to two times longer than stainless steel, providing superior wear resistance. The UL’s small, compact size reduces the chance for breakage.

• Creates air-filled droplets which significantly reduces spray drift• Wide 120° spray angle enables boom height to be lowered to further decrease drift• Engineered for superior spray uniformity at all pressures• Ideal use with pre-emergence and broad spectrum products• Precision-molded in tough and durable polyacetal• Small, compact size reduces the chances to of accidental breakage

Spray pattern: 120-deg. tapered flat fan Capacity: .15 to .80 US gal/min .57 to 3 l/min

15

JOHN DEERE SPRAY PARTSUltra Low-drift Air (ULA)

gpm@

40 psi

ULA 120 deg. — ASABE droplet classification data

10 pack

Quick-Change

PSULAQ20015PSULAQ2002PSULAQ20025PSULAQ2003PSULAQ2004PSULAQ2005PSULAQ2006PSULAQ2008

15 20 30 40 50 60 70 80 90 100 115psi psi psi psi psi psi psi psi psi psi psi

VC C C C C M M M M F FVC VC C C C C M M M M FVC VC C C C C M M M M MVC VC VC C C C C M M M MVC VC VC C C C C M M M MXC XC VC VC VC C C C C M MXC XC XC VC VC VC C C C C MXC XC XC VC VC VC C C C C M

0.150.200.250.300.400.500.600.80

10 pack

Nozzles

PSULA20015PSULA2002

PSULA2003PSULA2004PSULA2005PSULA2006 PSULA2008

PSULA20025


16

Ultra Plus Low-drift Air (ULAC)

ULTRA-Plus low drift ceramic — The ULAC air-aspirated spray nozzle produces large air-filled drop-lets that burst on impact, providing optimum drift-control capability and good target coverage. Its special two-part construction includes a removable pre-orifice, which makes cleaning easy. The ceramic nozzle and pre-orifice provide a long wear life, up to three times longer than stainless steel.

• Produces large air-filled droplets that burst on impact• Provides optimum drift control capability and good target coverage• Wear-resistant ceramic orifice

Spray pattern: 110 deg.-tapered flat fanCapacity: .10 to 1.0 US gal./min. .4 to 3.7 l/min

17

JOHN DEERE SPRAY PARTSUltra Plus Low-drift Air (ULAC)

"GPM @ 40 PSI"

ULAC 110 deg. - ASABE droplet classification chart QuickChange Nozzles

30 PSI

40 PSI

50 PSI

60 PSI

70 PSI

80 PSI

90 PSI

100 PSI

10 pack 10 Pack

0.10 VC VC VC VC C C C C PSULACQ1001 PSULAC1001

0.15 VC VC VC VC VC VC C C PSULACQ10015 PSULAC10015

0.20 VC VC VC VC VC VC VC C PSULACQ1002 PSULAC1002

0.25 XC VC VC VC VC VC VC VC PSULACQ10025 PSULAC10025

0.30 XC XC XC VC VC VC VC VC PSULACQ1003 PSULAC1003

0.40 XC XC XC VC VC VC VC VC PSULACQ1004 PSULAC1004

0.50 XC XC XC XC VC VC VC VC PSULACQ1005 PSULAC1005

0.60 XC XC XC XC VC VC VC VC PSULACQ1006 PSULAC1006

0.80 XC XC XC XC XC XC XC XC PSULACQ1008 PSULAC1008

1.00 XC XC XC XC XC XC XC XC PSULACQ1010 PSULAC1010


18

Twin Air (TAQ)

Spray pattern: 110 deg.-tapered flat fan Capacity: .2 to 0.80 US gal./min. .75 to 3.0 l/min

Twin Air — Twin Air spray nozzles are the best choice for high coverage applications where on target spray delivery is important. They are ideal for low crops with complex canopies, such as vegetables, where through coverage of the target and protection of the surroundings are of high importance.

• Forward and rear facing fans• Uniform coverage and reduced drift • Easy to install, patent pending locking ring and o-ring seal• Integrated strainers are matched to the nozzle size to prevent overstraining or plugging• Compact, break-resistant design fits on most common nozzle bodies

19

JOHN DEERE SPRAY PARTSTwin Air (TAQ)

GPM @ 40 PSI

TAQ 110-deg - ASABE droplet classification chart Quick Change

30 psi 40 psi 50 psi 60 psi 70 psi 80 psi 90 psi 100 psi 115 psi 10 pack

0.20 C M M M M M M F F PSTAQ1002

0.25 VC C M M M M M M M PSTAQ10025


0.40 C M M M M M M M M PSTAQ1004



0.80 VC VC C C M M M M M PSTAQ1008


20

Low-drift Air (LDA)

Spray pattern: 110 deg.-tapered flat fan Capacity: .15 to .50 US gal./min. .57 to 1.89 l/min

Low-drift air — LDA spray nozzles are patented air-educted nozzles specially designed toward achieving superior results.

• Produces air-induced sprays for reduced drift and environmental impact while increasing droplet deposition and retention on the foliage

• Provides better coverage with more drops per US gallon • Optimized for the productivity of the most common application rates• Delivers faster work rates with better drift reduction, allowing for more productive spray days• Each nozzle is clearly marked with an arrow indicating the direction of travel

21

JOHN DEERE SPRAY PARTSLow-drift Air (LDA)

gpm @ 40 PSI

LDA 110 deg- ASABE droplet classification data Quick-Change Nozzle

15 PSI

20 PSI

30 PSI

40 PSI

50 PSI

60 PSI

70 PSI

80 PSI

90 PSI

100 PSI

115 PSI

10 pack 10 pack

0.15 XC XC VC C C C M M M M M PSLDAQ10015 PSLDA10015

0.20 XC XC VC C C C M M M M M PSLDAQ1002 PSLDA1002

0.25 XC XC VC C C C C C M M M PSLDAQ10025 PSLDA10025






22

Guardian TM (LDX)

Spray pattern: 120-deg. wide-angleCapacity: .10 to .80 US gal./min. .4 to 3 l/min.

Guardian LDX — Designed to create a more-consistent droplet size, the new Guardian LDX quick-change nozzle reduces the amount of “driftable fines” across a wide variety of pressure settings. The one-piece design includes nozzle, cap, gasket, and strainer for easier handling. Its 120-degree angled pattern lets you spray closer to the target, reducing drift, while improving uniformity. A unique 20-degree incline increases application versatility to control diseases, insects, and weeds. And a bold arrow on the spray nozzle indicates incline direction for easy installation, and allows you to adjust your application to match the target. To aim the spray, simply aim the arrow.

• Applications of insecticide and fungicide• Delivers a more consistent droplet and spray pattern, making it versatile for more rates and speeds• Quick-change nozzle design eliminates loose nozzles, caps, gaskets and strainers for easier

installation and safer handling• Wide 120° pattern is inclined 20° to enhance application versatility• A bold arrow clearly indicates incline direction for easy installation

23

JOHN DEERE SPRAY PARTSGuardian TM (LDX)

GPM @ 40 PSI

LDX 120 deg.- ASABE droplet classification chart QuickChange

15 PSI

20 PSI

30 PSI

40 PSI

50 PSI

60 PSI

70 PSI

80 PSI

90 PSI

100 PSI

115 PSI

10 pack

0.10 C C C M M M M M M M M PSLDXQ2001

0.15 C C C M M M M M M M M PSLDXQ20015

0.20 VC C C C C M M M M M M PSLDXQ2002

0.25 VC C C C C M M M M M M PSLDXQ20025

0.30 VC C C C C C M M M M M PSLDXQ2003



0.60 XC VC C C C C M M M M M PSLDXQ2006

0.80 XC XC VC C C C M M M M M PSLDXQ2008


24

Low-drift (LD)

Spray pattern: 110-deg. tapered flat fan Capacity: .15 to .80 US gal./min. .57 to 3 l/min.

Low-drift poly — The drift-reducing LD nozzle produces fewer fine droplets than a standard flat fan and, with its dual air-education technology, produces large air-filled droplets, optimizing drift control and target coverage. Because of its drift-reducing flat spray, it allows operations in a wider weather window. Unlike other drift-reducing nozzles, the flow from the LD is a straight route through the nozzle, which decreases the chance for clogging. Made from polyacetal, the LD nozzle provides supe-rior wear resistance, up to twice as long as stainless steel.

• Applications of pre-emergent herbicides and post-emergent herbicides• Significantly reduces spray drift, widening the operational window• Dual air-eduction technology produces large air-filled droplets• Removable pre-orifice makes for easy cleaning• Precision-molded in tough and durable polyacetal

25

JOHN DEERE SPRAY PARTSLow-drift (LD)

6 pack

Quick-ChangeLD 80 deg. — ASABE droplet classification data

LD 110 deg. — ASABE droplet classification data

PMQLD80015PMQLD8002PMQLD8003PMQLD8004PMQLD8005PMQLD8006PMQLD8008

0.150.200.300.400.500.600.80

gpm@

40 psi

0.150.200.250.300.400.500.600.80

gpm @

40 psi 15 20 30 40 50 60 70psi psi psi psi psi psi psi

M M M M M M FC C M M M M MC C M M M M MC C C M M M MC C C M M M M

VC C C C C M MVC C C C C CVC VC C C C C C

15 20 30 40 50 60 70psi psi psi psi psi psi psi

C C M M M M MC C C M M M MC C C C M M MC C C C M M M

VC C C C C C MVC VC VC C C C CXC VC VC VC C C C

PSLD10015PSLD1002PSLD10025PSLD1003PSLD1004PSLD1005PSLD1006PSLD1008

10 pack

Nozzle

C


26

Low-drift Ceramic (LDC)

Spray pattern: 110-deg. tapered flat fan Capacity: .1 to .40 US gal./min. .4 to 1.5 l/min.

Low-drift Ceramic — The drift-reducing LDC nozzle produces fewer fine droplets than a standard flat fan and, with its dual air-eduction technology, produces large air-filled droplets, optimizing drift control and target coverage. Unlike other drift-reducing nozzles, the flow from the LDC is a straight route through the nozzle, which decreases the chance for clogging. The ceramic nozzle and pre-orifice provide a long wear life, up to three times longer than stainless steel.

• Droplet size balances drift reduction and target coverage• Pre-orifice design creates droplets that are well suited for a wide range of applications• Versatile and long-lasting tip• Wear-resistant ceramic orifice

27

JOHN DEERE SPRAY PARTSLow-drift Ceramic (LDC)

GPM @ 40 PSI

LDC 110 deg.- ASABE droplet classification data Nozzles

30 PSI 40 PSI 50 PSI 60 PSI 70 PSI 10 pack

0.10 M M F F F PSLDC10010

0.15 M M M M M PSLDC10015

0.20 M M M M M PSLDC1002

0.30 C M M M M PSLDC1003

0.40 VC C C C M PSLDC1004


28

Extended Range (ER)

Extended Range — The ER tip provides a consistent pattern and coverage over a wide range of oper-ating pressures — down to 15 psi — making it ideal for use with automatic rate controllers. It delivers a versatile spray pattern for applications of herbicides, fungicides, insecticides, and growth regula-tions. Molded completely out of polyacetal, the ER tip provides up to two times longer wear resistance to most agricultural chemicals compared to a stainless-steel insert.

• Applications of herbicides, fungicides, insecticides and growth regulations• Excellent spray distribution over a wide range of operating pressures• Precision-molded in tough and durable polyacteal• Provides up to two times longer wear resistance to most agricultural chemicals compared to

a stainless-steel insert

Spray pattern: 80- or 110-deg. tapered flat fan Capacity: 80-deg: .15 to .60 US gal./min .57 to 2.27 l/min. 110-deg: .15 to 1.5 US gal./min. .57 to 6 l/min.

29

JOHN DEERE SPRAY PARTSExtended Range (ER)

GPM @ 40 PSI

ER 80 deg.- ASABE droplet classification chart Quick Change Nozzles15 PSI 20 PSI 30 PSI 40 PSI 50 PSI 60 PSI 70 PSI 10 Pack 10 pack

0.15 M M F F F F F PSERQ80015 PSER80015


0.30 M M M F F F F PSERQ8003 PSER8003

0.40 C M M M M F F PSERQ8004 PSER8004

0.50 C C M M M M F PSERQ8005 PSER8005

0.60 C C C C M M M PSERQ8006 PSER8006

GPM @ 40 PSI

ER 110 deg.- ASABE droplet classification chart Quick Change Nozzles15 PSI 20 PSI 30 PSI 40 PSI 50 PSI 60 PSI 70 PSI 10 Pack 10 pack

0.15 M F F F F F F PSERQ10015 PSER10015



0.30 M M M F F F F PSERQ1003 PSER1003

0.40 C M M M M F F PSERQ1004 PSER1004

0.50 C C M M M M F PSERQ1005 PSER1005

0.60 C C C M M M M PSERQ1006 PSER1006

0.80 VC C C M M M M PSERQ1008 PSER1008

1.00 VC C C M M M M PSERQ1010 PSER1010

1.50 VC VC VC C C M M PSERQ1015 PSER1015


30

Extended Range Stainless Steel (ERI)

Spray pattern: 80-deg. tapered flat fan Capacity: .1 to 1.5 US gal./min. .4 to 6 l/min.

Extended Range Stainless Steel — The ERI nozzle provides a consistent pattern andcoverage over a wide range of operating pressures — down to 15 psi — making itideal for use with automatic rate controllers. It delivers a versatile spray pattern forapplications of herbicides, fungicides, insecticides, and growth regulations.

• Applications of herbicides, fungicides, insecticides and growth regulations• Adjustable droplet size according to pressure• Manages drift when used at a low pressure and gives excellent coverage at higher pressures• Insert is precision machined stainless steel

31

JOHN DEERE SPRAY PARTSExtended Range Stainless Steel (ERI)

GPM @ 40 PSI

ERI 80 deg.- ASABE droplet classification chart Quick Change Nozzles

15 PSI 20 PSI 30 PSI 40 PSI 50 PSI 60 PSI 70 PSI 10 Pack 10 pack

0.10 M F F VF VF VF VF PSERIQ8001 PSERI8001

0.15 M F F F F VF VF PSERIQ80015 PSERI80015

0.20 M M F F F F VF PSERIQ8002 PSERI8002

0.30 C M M F F F F PSERIQ8003 PSERI8003

0.40 C C M M M F F PSERIQ8004 PSERI8004

0.50 C C C M M M F PSERIQ8005 PSERI8005

0.60 C C C M M M M PSERIQ8006 PSERI8006

0.80 VC C C C C M M PSERIQ8008 PSERI8008

1.00 VC VC VC C C C M PSERSQ8010 PSERS8010

1.50 XC VC VC C C C C PSERSQ8015 PSERS8015


32

Extended Range Ceramic (ERC)

Extended Range Ceramic — The ERC nozzle provides a consistent pattern and coverage over a wide range of operating pressures — down to 15 psi — making it ideal for use with automatic rate control-lers. It delivers a versatile spray pattern for applications of herbicides, fungicides, insecticides, and growth regulations. The ceramic nozzle provides a long wear life.

• Applications of herbicides, fungicides, insecticides and growth regulations• Droplet size suited for target coverage• Wear-resistant ceramic orifice • Wide range of operating pressures

Spray pattern: 110-deg. Tapered flat fan Capacity: .15 to .60 US gal./min. .57 to 2.27 I/min.

33

JOHN DEERE SPRAY PARTSExtended Range Ceramic (ERC)

GPM @ 40 PSI

ERC 110 deg.- ASABE droplet classification chart Quick Change Nozzles

20 PSI 30 PSI 40 PSI 50 PSI 60 PSI 70 PSI 10 Pack 10 pack

0.15 F F F F F VF PSERCQ10015 PSERC10015

0.20 F F F F F F PSERCQ1002 PSERC1002

0.30 M M M F F F PSERCQ1003 PSERC1003

0.40 M M M M M F PSERCQ1004 PSERC1004

0.50 M M M M M M PSERCQ1005 PSERC1005

0.60 M M M M M M PSERCQ1006 PSERC1006


34

Flat Fan (FF)

Spray pattern: 80- or 110-deg. tapered flat fan Capacity: 80-deg: .067 to 2.0 US gal./min .253 to 7.5 l/min. 110-deg: .1 to 2.0 US gal./min. .4 to 7.5 l/min.

Flat Fan — The FF nozzle with its simple, one-piece design creates a flat sheet of spray and provides a consistent pattern over a range of pressures. The mixed droplet spectrum makes this product suited for applications of herbicides, fungicides, insecticides, and PGRs. It’s an economical option for moder-ate use. Made from polyacetal, the FF nozzle provides superior wear resistance.

• Applications of herbicides, fungicides, insecticides, and PGRs• Mixed droplet spectrum allows effective delivery and retention of agrochemicals• Precision-molded in tough and durable polyacetal• Superior wear resistance

35

JOHN DEERE SPRAY PARTSFlat Fan (FF)

PSFF800067PSFF8001PSFF80015PSFF8002PSFF8003PSFF8004PSFF8005PSFF8006PSFF8008PSFF8010PSFF8015PSFF8020

10 pack

NozzleFF 80 deg. — ASABE dropletclassification data

30 40 50 60psi psi psi psi

VF VF VF VFF F F FM F F FM M F FC M M FC M M MC M M MC C M MC C C C

VC C C CVC VC C CVC VC VC VC

PSFF1001PSFF10015PSFF1002PSFF1003PSFF1004PSFF1005PSFF1006PSFF1008PSFF1010PSFF1015PSFF1020

10 pack

NozzleFF 110 deg. — ASABE dropletclassification data

30 40 50 60psi psi psi psi

F F F FF F F FF F F FM F F FM M M FM M M MM M M MC C C CC C C CC C C CC C C C

0.0670.100.150.200.300.400.500.600.801.001.502.00

gpm@

40 psi

0.100.150.200.300.400.500.600.801.001.502.00

gpm@

40 psi


36

High Flow (HF)

High Flow — The HF spray nozzle features a unique flat-fan spray design for excellent spray distribu-tion and free flow for improved spray consistency. Low CV (Coefficient of Variation) performance rat-ings provide excellent distribution. The 140-degree angled spray pattern provides excellent distribu-tion in wide-spaced setups (30, 40, 45, or 60 inch). Made from polyacetal, the high-flow spray nozzle provides superior wear resistance.

• Straight-through design to reduce clogging• Incredibly uniform application across the boom• The 140° pattern allows lower spray heights to reduce the risk of drift during sensitive appli-

cations• Superior wear resistance

Spray pattern: 140-deg. wide-angle floodCapacity: .80 to 6.0 US gal./min. 3 to 22.7 l/min.

37

JOHN DEERE SPRAY PARTSHigh Flow (HF)

GPM @ 40 PSI

HF 140 deg.- ASABE droplet classification chart QuickChange

20 PSI 30 PSI 40 PSI 50 PSI 60 PSI 70 PSI 80 PSI 10 pack

0.80 XC XC XC XC XC XC XC PSHFQ4008









38

Flood (FL)

Spray pattern: 105- to 145-deg. wide-angle floodCapacity: .2 to 2.0 US gal./min. .75 to 7.5 l/min. Polyacetal-molded for excellent life

Flood— The FL nozzle produces large droplets in a wide, flat, 105- to 145-degree spray angle pattern suited for pre- and post-emergent herbicides. This flexible nozzle can be used in 20- to 60-inch nozzle spacing applications. Its large orifice produces coarser droplets, which are less prone to drift. The FL’s large, circular orifice reduces the chances of blocking. Made from polyacetal, the FL nozzle provides superior wear

• Spray angle pattern suited for pre and post-emergent herbicides• Large orifice produces coarser droplets which are less prone to drift• Large circular orifice reduces the chances of blocking• Precision-molded in tough and durable polyacetal

39

JOHN DEERE SPRAY PARTSFlood (FL)

GPM @ 10 PSI

Spray Angle

FL-Flood.- ASABE droplet classification chart Nozzles

10 PSI 20 PSI 30 PSI 40 PSI 50 PSI 60 PSI 10 pack

0.20 105 C C M M M M PSFL2

0.25 110 C C M M M M PSFL025

0.30 110 C C M M M M PSFL3

0.40 120 C C M M M M PSFL4

0.50 125 C C C M M M PSFL5

0.75 145 C C C C C C PSFL75

1.00 160 VC VC C C C C PSFL10

1.50 145 XC VC VC C C C PSFL15

2.00 140 XC VC VC VC C C PSFL20


40

Straight Stream Ceramic (STC)

Spray pattern: six straight streams at 110-deg.Capacity: .15 to 1.5 US gal./min. .57 to 6 l/min

Straight Stream Ceramic — The STC nozzle is ideal for liquid fertilizer application. Its 110-degree spray angle provides accurate span distribution and target coverage, and its ceramic orifice provides maximum wear resistance and accurate, uniform distribution. This nozzle provides extremely coarse droplets, improving fertilizer distribution, and a minimized risk of leaf burn.

• Six streams distribute fertilizer more evenly than on single pattern• Provides extremely coarse droplets• Reduced atomization limits leaf burn and scorching• Wear-resistant ceramic orifice

41

JOHN DEERE SPRAY PARTSStraight Stream Ceramic (STC)

GPM @ 40 PSI

STC-Straight Stream-ASABE dropplet classification chart QuickChange

15 PSI 20 PSI 30 PSI 40 PSI 50 PSI 60 PSI 10 pack

0.15 XC XC XC XC XC XC PSSTCQ10015











42

Straight Stream (ST)

Spray pattern: straight stream Capacity: 1.0 to 2.0 US gal./min. 3.7 to 7.5 l/min.

Straight Stream — 0-degree ST regulates flow, then produces a straight stream pattern.

• Provides a single jet of spray for streaming or injecting liquid fertilizer• Precision molded using chemically-resistant PVDF• Superior resistance to orifice wear

43

JOHN DEERE SPRAY PARTSStraight Stream (ST)

GPM @ 40 PSI

ST- Straight stream .- ASABE droplet classification data Nozzles

15 PSI 20 PSI 30 PSI 40 PSI 60 PSI 10 pack

1.0 XC XC XC XC XC PSST10




44

Hollow Cone Ceramic (HCC)

Hollow Cone Ceramic — The HCC nozzle produces a fine droplet in a hollow-cone, 80-degree pattern. Its special two-part construction includes a removable pre-orifice, which makes for easy cleaning. The ceramic nozzle and pre-orifice provide a long wear life.

• Applications of insecticide and fungicide• Produces finely atomized droplets in a hollow-cone, 80-degree pattern• Special two-part construction includes removable pre-orifice, makes for easy cleaning• Ceramic nozzle and pre-orifice provide a long wear life

Spray pattern: 80-deg. hollow cone Capacity: .03 to .17 US gal./min. .11 to .64 l/min.

45

JOHN DEERE SPRAY PARTSHollow Cone Ceramic (HCC)

Quick-ChangeHCC 80-deg. — ASABE droplet classification data

PMHC3PMHC4PMHC6PMHC8PMHC10PMHC12PMHC18

6 pack

Tip HC — ASAE droplet classification data

40 50 60 70 80 90 100 125 150psi psi psi psi psi psi psi psi psi

F F VF VF VF VF VF VF VFF F VF VF VF VF VF VF VFF F F VF VF VF VF VF VFF F F F F VF VF VF VFF F F F F F VF VF VFF F F F F F F VF VFF F F F F F F F VF

40 50 60 70 80 90 100 125 150 350psi psi psi psi psi psi psi psi psi psi

VF VF VF VF VF VF VF VF VF VFVF VF VF VF VF VF VF VF VF VFVF VF VF VF VF VF VF VF VF VFF F F F VF VF VF VF VF VFF F F F F F VF VF VF VF

PM904-6PM904-6PM904-1PM904-6PM904-6PM904-1PM904-1

6 pack

Cap(includes gasket)gpm @

15 psi

gpm @15 psi

.03

.04

.06

.12

.17

.03

.04

.06

.08

.10

.12

.18

PSHCCQ3PSHCCQ4PSHCCQ6PSHCCQ12PSHCCQ17

10 pack


46

Even Spray (ES)

Even-spray poly — The ES nozzle produces a flat, even spray which provides uniform distribution across the spray band. It is an excellent choice for band applications of pre and post-emergent herbi-cides and fungicides, and directed post applications. The band width can be changed by adjusting the spray nozzle height. Made from polyacetal, the ES nozzle provides superior wear resistance to agricul-tural chemicals.

• Provides uniform distribution across the spray band• Excellent choice for pre and post-emergent herbicides and fungicides and direct post applications• Width can be adjusted by spray nozzle height• Provides superior wear resistance

Spray pattern: 80-deg. tapered flat fan Capacity: .1 to .8 US gal./min. .4 to 3 l/min.

47

JOHN DEERE SPRAY PARTSEven Spray (ES)

30 40 50 60psi psi psi psiF F F FM F F FM M M FC M M MC C M MC C C CC C C C

VC C C C

PSES8001PSES80015PSES8002PSES8003PSES8004PSES8005PSES8006PSES8008

10 pack

NozzleES 80 deg. — ASABE dropletclassification datagpm @

40 psi

0.100.150.200.300.400.500.600.80


48

Chemical Resistant (CR)

Chemical-resistant polyvinylydene fluoride — The CR nozzle with its simple, one-piece design creates a flat sheet of spray and provides a consistent pattern over a range of pressures. The mixed droplet spectrum makes this product suited for applications of herbicides, fungicides, insecticides, and PGRs. It also allows effective delivery and retention of agrochemicals. The CR nozzle is produced from polyvinylydene fluoride for use in demanding chemical situations, such as acid-based defoliation products.

• Applications of herbicides, fungicides, insecticides and PGRs• Creates flat sheet of spray and provides consistent pattern over a range of pressures• Molded from polyinylydene fluoride for use in demanding chemical situations, such as acid-

based defoliation products

Spray pattern: 110-deg. tapered flat fan Capacity: .2 to 1.5 US gal./min. .75 to 6 l/min.

49

JOHN DEERE SPRAY PARTSChemical Resistant (CR)

PSCR1002PSCR1003PSCR1004PSCR1005PSCR1006PSCR1008PSCR1010PSCR1015

10 pack

NozzleCR 110 deg. — ASABE droplet classification

30 40 50 60psi psi psi psiF F F F0.20

0.300.400.500.600.801.001.50

gpm@

40 psi

M F F FM M M FM M M MM M M MC C C CC C C CC C C C


50

Off center — OC— brass nozzle

Spray pattern: off centerCapacity: .2 to .6 US gal./min. .75 to 2.27 l/min.

Off-center brass — The OC nozzle produces a flat spray for use on boom ends to extend spray reach, improve coverage, and reduce risk of equipment damage. Made from brass, the OC is intended for moderate use.

• Produces a flat spray for use on boom ends to extend spray reach• Reduce risk of equipment damage• Made from brass • Intended for moderate use

51

JOHN DEERE SPRAY PARTSOff center — OC— brass nozzle

PSOCB8002PSOCB8003PSOCB8004PSOCB8006

10 pack

NozzleOC 80 deg. – ASABE dropletclassification data

30 40 50 60psi psi psi psiM M M FM M M FC M M MC C M M

gpm @40 psi

0.200.300.400.60


52

Fence Row/Boomless (XT)

Spray pattern: off center, distances up to 16.5 ft.Capacity: 1.0 to 2.4 US gal./min. 3.7 to 9 l/min.

Fence Row/Boomless- XT introduces boomless spray technology, enabling spray to be targeted into places that conventional booms and other nozzles cannot reach.

• Common uses include orchard, vineyard, forestry, pasture, turf and golf courses.• Excellent low-drift option while extending spray reach• Maintains a consistent spray swath over a pressure range of 30-60psi• 105 degree spray angle

53

JOHN DEERE SPRAY PARTSFence Row/Boomless (XT)

PM3489HPM3488HPM3488APM3489APM3488BPM3489B

Replacement parts Description

XT010 stainless-steel insertXT010 polyacetal pattern generatorXT020 stainless-steel insertXT020 polyacetal pattern generatorXT024 stainless-steel insertXT024 polyacetal pattern generator

Thread size Pkg. qty.

1/4 in.1/4 in.3/8 in.3/8 in.1/2 in.1/2 in.

111111

PSXTIQ10

PSXTIQ20

PSXTIQ24

Capacity and spacing data Flow rate replaced at 20-in. spacing

40.0

40.0

40.0

Flow rate replaced at 30-in. spacing

1.0

2.0

2.4

16

17

18

Partnumber

psi gpm Distance(ft.)

Effectivedistance (ft.)

Number oftips replaced

Flow rateper tip

Type of tipreplaced

Number oftips replaced

Flow rateper tip

Type of tipsreplaced

14.5

15.5

16.5

8.7

9.3

9.9

0.115

0.215

0.242

80 or 110 deg.0.1 gpm

80 or 110 deg.0.2 gpm

80 or 110 deg.0.25 gpm

5.8

6.2

6.6

0.172

0.323

0.364

80 or 110 deg.0.2 gpm

80 or 110 deg.0.3 gpm

80 or 110 deg.0.4 gpm


54

Twin caps

Part number Description Pkg. qty.

PMTC Twin cap 6

PM1TC Twin cap 40

PM65MN01113

Twin cap internal seal 6PMTCCR

Twin cap, chemical resistant 6

TwinCapTM- TwinCap is a simple, compact way of accommodating two spray tips back to back. This design allows you to apply the volume per acre you want, at the speed you want, without compromising spray quality.

• Improve control of plant diseases, insects, and difficult weeds• Twin 30° angles improve canopy penetration• Combined forward and backward angles enhance coverage on stems and leaves• Holds any two standard dimension tips: ULA, LD, LDC, ER, ERI, Flat and Even nozzles

(sold separately)

55

JOHN DEERE SPRAY PARTSAdapters for nozzle body

• Use John Deere spray nozzles and quick-change caps on Hardi® or Jacto™ sprayers.

• Converts Hardi or Jacto nozzle bodies to standard quick-change lugs.

• Adds only 1/2-in. to length of nozzle body.• Adapter and EPDM gasket included

Part number Description Pkg. qty.

PM99500024 Hardi adapter 10PM99500027 Jacto adapter 10

Hardi is a registered trademark of Hardi, Inc.Jacto is a registered trademark of Jacto, Inc.


56

Spray Nozzle Caps

Spray Nozzle Caps — Caps provide trouble-free spray nozzle installation and sealing on nozzle bodies and several other common makes.

• Color coded to ISO standards for nozzle flow to simplify nozzle selection and identification in the field

• Caps for fan pattern nozzles automatically align nozzles for enhanced spray uniformity

57

JOHN DEERE SPRAY PARTSSpray Nozzle Caps

ISO Standard Fan

European Fan(Thick body)

Standard Round (Non-aligning)

Shut-off Threaded

Fits:ULA, LDA, LD,

ER, ERI, OC, FF, ES, ERC

ULAC, STCHC, D-C, FL

flanged hose barbsBlank 1/4”MNPT Std.

Pack

Black PS90020 PS90120 PS90420 PS90920 PS91020 10

Orange PS90001 PS90101 PS90401 - - 10

Green PS900015 PS901015 PS904015 - - 10

Yellow PS90002 PS90102 PS90402 - - 10

Lilac PS900025 PS901025 PS904025 - - 10

Blue PS90003 PS90103 PS90403 - - 10

Dark Red PS900035 - - - - 10

Red PS90004 PS90104 PS90404 - - 10

Brown PS90005 PS90105 PS90405 - - 10

Gray PS90006 PS90106 PS90406 - - 10

White PS90008 PS90108 PS90408 - - 10Included EPDM seal PM200040-1 PM200040-1 PM200040-1 - PM200040-1 -Included Nitrile seal - - - PM65BS205 - -Separate Viton seal PM200040VI PM200040VI PM200040VI - PM200040VI -


58

Plumbing Products

From nozzle bodies to pressure gauges to spray guns, we have what you need in plumbing accessories. See your dealer for information on the complete plumbing products line.

•Nozzlebodies•Pressureguages•Fittings•Sprayguns•Valves

59

JOHN DEERE SPRAY PARTSPumps

For today’s machinery and tomorrow’s demands, John Deere pumps are leaders in the industry. See your John Deere dealer to match the right pump to your equipment and task.

•Centrifugal•Roller•Accessories


60

Application support

Foams, dyes, and cleaners stand up to tough, demanding conditions. From the long-lasting ULTRAX™ marking foam to our exclusive winterizer fluid, your John Deere dealer has all the products you need to support your spray application.

•Foams•Dyes•Cleaners•Winterizer

61

JOHN DEERE SPRAY PARTSLiquid-handling products

Liquid-handling products are made from glass-reinforced polypropylene. This high-quality material provides excellent chemical and corrosion resistance, rigidity, light weight, stress-cracking resistance, low moisture absorption, and good impact resistance.

•Valves•Electricvalves•Manifoldsystems•IBC/tankaccessories•Polyproyleneand316stainless- steel couplings•Pipefittings•Linestrainers

DSPG43512 Litho in U.S.A. (11-04)

Documents

John Deere Spraying Solutions · PDF fileJohn Deere Spraying Solutions ... When you’re in the market for spray nozzles and accessories, ... The American Society of Agricultural and