Upload
gaurshashikant4432
View
229
Download
6
Tags:
Embed Size (px)
DESCRIPTION
111
Citation preview
1
Final Technical Repor t
on
DEVELOPMENT OF JUTE FIBER REINFORCED
CEMENT CONCRETE COMPOSITES
2
F INAL P ROJECT REPORT
ON
The Project: DEVELOPMENT OF JUTE FIBER REINFORCED CEMENT CONCRETE COMPOSITES
Project No: JMDC/JTM/MM-IV/7.1/2008, Dated: 31.3.2008
Sponsored by National Jute Board Ministry of Textile
Govt. of India 3A, Park Plaza, 71, Park Street,
Kolkata-7000016
Materials Science Centre Indian Institute of Technology
Kharagpur 721302 June 2011
3
Contents
SECTION A: GENERAL INTRODUCTION
A.1. Introduction A.2. Background A.3. Task and deliverable A.4. Scope and objectives A.5. Work plan
SECTION B: MODIFICATION AND CHARACTERIZATION OF JUTE FIBER
B.1. Materials
B.2. Chemical modification of jute fiber
B.2.1. Alkali treatment B.2.2. Polymer treatment
B.3. Characterization of untreated and chemically treated jute fiber
B.3.1. FTIR spectroscopy B.3.2. X-ray diffraction B.3.3. Surface topography studies of fiber by scanning electron microscope (SEM) B.3.4. Water absorption and hydrophilicity study of jute fiber B.3.5. Tensile properties B.3.6. Durability study of untreated and treated jute fiber in cement matrix
SECTION C: FABRICATION AND CHARACTERIZATION OF JUTE REINFORCED
CEMENT COMPOSITE
C.1. Materials
C.2. Physical characterization of Portland Pozzolonic cement: Initial and final
setting time of cement paste
C.3. Processing of untreated and chemically treated jute fiber reinforced cement
mortar /concrete composites
C.4. Physical and mechanical characterization of untreated and treated jute fiber
reinforced cement mortar
C.4.1. Bulk density C.4.2. Flow table value C.4.3. Microstructure analysis of jute fiber reinforced mortar composite C.4.4. Compressive strength C.4.5. Flexural strength C.4.6. Relation between density ratio and strength ratio
4
C.4.7. Extensibility
C.5. Physical and mechanical properties of untreated and treated jute fiber
reinforced concrete
C.5.1. Slump test C.5.2. Specific gravity C.5.3. Microstructure analysis of jute fiber reinforced concrete composite C.5.4. Compressive strength C.5.5. Flexural strength
SECTION D: INDUSTRIAL FIELD TRIAL FOR PRODUCT DEVELOPMENT
D.1. Identification of products
D.2. Prototype development of jute fiber reinforced concrete pipe
D.2.1. Preparation of concrete for pipe fabrication
D.2.1.1. Characterization of lab based concrete composites required for pipe fabrication
D.2.2. Fabrication of jute fiber reinforced concrete pipe (NP3) D.2.3. Fabricated concrete pipes with and without modified jute fiber reinforcement D.2.4. Standard testing of manufactured jute fiber reinforced concrete pipes
D.3. Prototype development of jute fiber reinforced concrete electric pole
D.3.1. Preparation of concrete composites for pole fabrication D.3.1.1. Physical characterization of ordinary portland cement (OPC) D.3.1.2. Characterization of concrete for pole fabrication
D.3.2. Fabrication of jute fiber reinforced prestressed concrete electric pole D.3.3. Fabricated concrete poles with modified jute fiber reinforcement D.3.4. Standard testing of fabricated jute fiber reinforced concrete pole
D.4. Prototype development of jute fiber reinforced concrete pavers
D.4.1. Fabrication of jute fiber reinforced concrete pavers D.4.2. Fabricated concrete paver blocks with and without modified jute fiber reinforcement D.4.3. Standard testing of manufactured jute fiber reinforced concrete paver blocks
D.5. Development of jute fiber reinforced cement fly ash roof sheet
SECTION E: SUMMARY AND ACHIEVEMENT
SECTION F: MARKET SURVEY AND NEED ASSESSMENT
5
F.1. Introduction F.2. Identified products and its applications F.3. Cost analysis of identified products
F.3.1. Costing of Precast concrete (PCC) poles F.3.2. Costing of NP3 pipes F.3.3. Costing of NP4 pipes
F.4. Need Assessment and Market Survey F.4.1. Need Assessments F.4.2. Market survey
F.4.3. Companies view on jute reinforced cement concrete products F.5. Industrial collaboration for product commercialization
F.5.1. Rural Concreting Company of Ghatal Pvt Ltd F.5.2. H B Housing Industries F.5.3. Bose Abasan Prakalpa
F.6. Conclusions F.7. Bibliography
SECTION G: PATENTS AND PUBLICATION
G.1. Patents
G.2. Conferences
G.3. Workshop
G.4. Papers
G.5. Cumulative Reports
6
Project team
Prof Basudam Adhikari, Principal Investigator
Prof Subhasish Basu Majumder, Co-Principal Investigator
Mr. Rituparna Sen, Co-Investigator
Dr Ratan Kumar Basak, Project Consultant
Sarada Prasad Kundu, Project scholar
Sumit Chakraborty, Project scholar
Aparna Roy, Project scholar
Project team working at IIT, Kharagpur
7
SECTION A
General introduction
8
A.1. Introduction
The design of a durable and low cost fiber reinforced cement concrete for building
construction is a technological challenge in developing countries. The type of fibers currently
been used include steel, glass, polymers, carbon and natural fibers. Economic considerations
have restricted the use of carbon fibers in cementitious composites on a commercial level for
their non ecological performance. Natural fibers have the potential to be used as reinforcement to
overcome the inherent deficiencies in cementitious materials. Considerable researches are being
done for use of reinforcing fibers like jute, bamboo, sisal, akwara, coconut husk, sugarcane
bagasse in cement composites mostly in case of building materials. Use of natural fibers in a
relatively brittle cement matrix has achieved considerable strength, and toughness of the
composite. The durability of such fibers in a highly alkaline cement matrix must be taken into
consideration by effective modifications. A specific chemical composition has to be chosen that
can modify the fiber surface as well as strengthen the cement composite.
A.2. Background
Cement concrete composite is the most important building material and its consumption
is increasing in all countries. The only disadvantage of cement concrete is its brittleness, with
relatively low tensile strength and poor resistance to crack opening and propagation and
negligible elongation at break. To overcome these discrepancies reinforcement with dispersed
fibers might play an important role. Steel is the conventional reinforcing material in concrete.
Although steel enhances the strength and modulus of concrete but it lacks the ability to absorb
mechanical impact. The steel makes the reinforced cement concrete (RCC) structure heavy and
in due course of time as a result of water/moisture diffusion through micro crack developed in
the RCC structure steel starts corroding leading to failure of the concrete. On the contrary, if the
micro crack formation and propagation can be minimized by dispersion of short fibers, the
mechanical properties as well as the durability of the concrete can be improved. Such a system
would be able to bear high level static as well as dynamic stress. Natural (cellulosic) fibers might
offer the opportunity as a convenient reinforcing agent in concrete composite due to its low
density and high tensile property. In recent years, considerable research efforts are found to
develop high-strength, natural fibers reinforced concrete composites, mostly for using as
building and construction materials.
9
Natural fibers, isolated from plants, are classified into three categories, depending on the
part of the plant they are extracted from. The first category is the so called fruit fiber (e.g., coir,
cotton, etc.) which are extracted from fruits of the plant. The second category of the fiber is
found in the stems of the plant (e.g., jute, flax, ramie, hemp, etc). Such fibers are known as bast
fiber. The third category is the fibers extracted from the leaves (e.g., sisal, date palm, oil palm,
etc.).
Polymer modified jute fibers have been decided to be used as reinforcing element in
cement concrete in which polymer will chemically bridge jute in one side and cement on the
other side. Polymer modified jute fiber is expected to act as a flexible reinforcing agent in
cement concrete enabling it to transmit both static and dynamic stresses to its surrounding bulk
as well as absorb a portion of the stress by virtue of its flexible nature. An optimized weight
fraction of polymer modified jute fiber in cement concrete may lead to excellent mechanical
properties. It has been anticipated that modification of jute fiber with polymer will reduce
degradation possibilities.
Fiber reinforced concrete has been investigated extensively to make light weight
corrosion free structural materials. There are global attempts to use natural fibers as reinforcing
agent in cement concrete matrices. The advantages of natural fibers over the conventional
reinforcing fibers like glass, synthetic (e.g., polypropylene, polyethylene and polyolefin,
polyvinyl alcohol), carbon, steel etc., are: abundant availability, low cost, less abrasiveness,
ability to absorb mechanical impact, easy to handle and process and environmental friendliness.
These composites can be used in various fields of applications such as permanent frameworks,
paver blocks, wall panels, pipes, long span roofing elements, strengthening of existing structures
and structural building members. The natural fiber reinforced concrete composites present
enhanced strength and are likely to encounter a range of static overload and cyclic loading due to
possible wind or earthquake loading. When concrete matrix cracks under load, the fibers bridge
the cracks and transfer the loads to its surrounding bulk as well as absorb a portion of the load by
virtue of its flexible nature. Several investigations have been carried out with different
lignocellulosic fibers like, wheat straw, rice straw, coir, hazelnut shell, bagasse, oil palm
residues, arhar stalks, etc., to find the potentiality of natural fibers as an effective reinforcement
10
in concrete composites. But no report is found on the use of jute fiber as reinforcement in cement
concrete.
Based on the present scenario it has been anticipated that the jute fiber reinforced cement
concrete may find potential application as structural items in construction industry. Being a
potential agricultural product, the use of jute as reinforcing fiber in cement concrete will promote
jute farming industries as well as produce better advanced composites.
A.3. Task and deliverables
Tasks of this project:
Development of modified jute fiber: Modification of jute fiber with suitable chemical and polymer for its surface activation.
Development of unmodified and modified chopped jute fiber reinforced cement concrete composite.
Prototype development of modified jute fiber reinforced cement concrete products. Market needs and assessment of modified jute fiber reinforced cement concrete products.
Deliverables of this project
Selective choice and composition optimization of chemical and polymer for modification of jute fiber.
Optimized process development for mixing and casting of jute fiber reinforced cement concrete composite.
Optimized fiber length and loading in cement composite for best possible mechanical properties.
Prototype products like precast concrete pipes, prestressed concrete pole and precast concrete pavers block.
Market survey A.4. Scope and objectives of present investigation
There are two prominent research issues associated with the use of jute fiber in cement
concrete. First is the hydrophilicity of natural fiber. The high hydrophilicity of natural fiber
makes the wet concrete stiff and non workable due to gradual absorption of water from the wet
11
concrete mixture. The second research issue is the agglomeration of the chopped jute fiber
during concrete mixing leading to inhomogeneous fiber dispersion in the concrete matrix. Hence
the major challenges in this project is to
Reduce hydrophilicity of jute fiber by surface modification Reduce fiber agglomeration in concrete matrix Formulate a novel mixing technique and fabrication of jute fiber reinforced
cement concrete/mortar having improved physical and mechanical properties.
The objectives of this project are:
To evaluate the suitability of short jute fiber as a reinforcing agent in cement concrete/mortar.
Optimization of length of short jute fiber and its loading in cement matrix. Modification of jute fibers with chemicals and polymers and characterization of modified
jute fiber.
Mixing and casting of untreated and chemically modified jute fiber reinforced cement concrete/mortar.
Physical, mechanical and structural characterization of fabricated cement concrete/mortar.
Durability study of jute fiber in cement concrete matrix. Prototype development of jute fiber reinforced concrete/mortar products.
A.5. Work plan
The following work plan was formulated keeping in view the above objectives
Chemical modification of jute fiber Characterization of unmodified and chemically modified jute fiber Fabrication of jute reinforced cement composite Testing and characterization of jute fiber reinforced cement composite Industrial field trial and prototype product development
12
SECTION B
Modification and characterization of jute fiber
13
B.1. Materials
Jute fibers of TD4 grade were collected from Gloster Jute Mill, Howrah, India. Analytical
grade sodium hydroxide (NaOH) of Merck, India and commercially available carboxylated
styrene-butadiene copolymer based polymer latex (Sika Polymer latex Power) were used for
fiber surface modification.
B.2. Chemical modification of jute fiber
From the polar chemical nature and structure of natural fiber it appears that such fibers
can interact with polar nature of cement concrete. This concept justifies the reinforcing action of
jute in cement concrete. Simultaneously due to polar character of natural fiber, viz., jute, it shows
hydrophilic character. Such hydrophilicity might lead to depletion of water from the wet concrete
mix as well as it might degrade in due course of time as a result of microbial attack. To
overcome such shortcomings jute fibers need suitable physicochemical modification before
incorporation in concrete matrix. It was anticipated that after modification with alkali and other
chemical constituents, microbial degradation of jute fiber can be either delayed or prevented.
B.2.1. Modification with alkali
The jute fibers were cut to ~6 cm of length and soaked in 0.25, 0.5 and 1.0% (w/v) NaOH
solution at ambient temperature maintaining a fiber to liquor ratio of 1:30. The fibers were kept
immersed in the alkali solution for 0.5, 1, 2, 4, 8, 16, 24, 36 and 48 h. The alkali treated fibers
were then washed several times with distilled water to remove excess alkali from the fiber
surface. The final pH was maintained at 7.0. The fibers were then air dried at room temperature
for 24 h followed by oven drying at 55oC for 24 h. The plausible reaction between jute fiber and
alkali is shown in Scheme 1a.
Scheme 1a. Plausible reaction between jute fiber and alkali
14
B.2.2. Modification with polymer latex
Commercially available aqueous emulsion of carboxylated styrene-butadiene copolymer
based polymer latex was used to modify the jute fibers. The solid content of undiluted polymer
latex was found to be 41%. Alkali treated jute fibers were dipped into 0.25, 0.5, and 1.0% (v/v)
polymer latex for 24 h, maintaining a liquor ratio 1:30 at ambient condition. The fibers were then
air dried at room temperature for 24 h followed by oven drying at 55oC for 24 h. The plausible
reaction chemistry of alkali treated jute fiber and polymer latex is shown in Scheme 1b.
Scheme 1b. Plausible reaction chemistry of alkali treated jute fiber and polymer latex
B.3. Characterization of unmodified and modified jute fiber
B.3.1. Chemical characterization by FTIR spectroscopy
FTIR spectroscopic study of unmodified and modified jute fiber was performed by
Thermo Nicolet, Nexus 870 spectrophotometer with a scanning range from 4000 to 500 cm-1. In
the FTIR study of untreated and alkali treated jute fiber a characteristic broad absorbance band at
32003600 cm-1 range is observed for hydrogen bonded OH stretching (Fig. 1a). The
absorbance peak at 2910 cm-1 represents CH stretching vibration of methyl and methylene
groups in cellulose and hemicellulose. The absorbance bands at 1452 cm-1, 1374 cm-1 and 1035
cm-1 are ascribed to CH3 asymmetric, CH symmetric stretching and aromatic CH in plane
deformation in lignin respectively. The band at 1738 cm-1 for CO stretching of the carboxyl and
15
acetyl groups in hemicellulose part of the fiber was prominent in raw jute fiber. But this peak
gradually decreases as the time of alkali treatment on jute fiber increases and finally disappears
in 24 h 0.5% alkali treated fiber. When alkali treated jute fiber was modified with polymer latex
the band at 1738 cm-1 reappears (Fig. 1b). This may be due to the formation of an ester type
linkage between OH group of jute fiber and COOH group of carboxylated styrene butadiene
polymer present in the polymer latex.
Fig. 1a. FTIR spectra of jute fiber: (a) untreated, (b) 0.5 h, 0.5% alkali treated, (c) 2 h, 0.5% alkali treated, (d) 8 h, 0.5% alkali
treated, (e) 24 h, 0.5% alkali treated.
Fig. 1b. FTIR spectra of jute fiber: (a) raw (b) 0.5%, 24 h alkali treated, (c) 0.5%, 24 h alkali treated and 0.5% latex
treated jute fiber.
B.3.2. X-ray diffraction
X-ray diffraction data of the powdered jute fiber samples were collected using a
RIGAKU X-ray diffractometer (ULTIMA III). The XRD study was done maintaining the
operating range between 100 and 500 and a scanning speed of 20 /min. The crystallinity index and
crystallite size were calculated. The crystallite size and crystallinity index were also calculated
from the X-ray diffractogram. From Table 1a it can be observed that the crystallite size and
crystallinity index increase with the increase in time of alkali treatment. But the FWHM of
diffraction peak decreases after alkali treatment. The increment of crystallinity index and
crystallite size is due to the removal of amorphous components of jute fiber.
16
Table 1a. Calculated and observed crystalline parameters from XRD diffractograms of raw and alkali treated jute fibers
But when alkali treated jute fibers were further treated with polymer latex, the amorphous
polymer was dispersed in the inter-fibrillar region of fiber, which might decrease the CrI (Table 1b). Table 1b. Calculated and observed crystalline parameters from XRD diffractograms of latex treated jute
Latex (v/v %)
Peak position (2)
FWHM (2) Area (%) Amplitude (counts/s)
Crystallite size (nm)
CrI (%)
15.76 5.93 47.11 371.20 1.69 0.25 22.40 3.10 52.88 797.87 2.27
53.47
15.51 4.76 43.47 433.65 2.14 0.50 22.31 2.82 56.52 950.04 2.51
54.36
15.43 5.90 46.66 422.23 1.73 1.00 22.33 3.21 53.33 886.32 2.20
52.36
B.3.3. Surface topography studies of jute fiber by scanning electron microscope (SEM)
The surface topography of jute fibers was investigated to examine the effect of chemical
treatment upon the fiber surface using a scanning electron microscope (SEM). The powdered
samples were coated with a thin layer of gold and scanning electron micrographs of fiber
samples were taken in TESCAN VegaLSV SEM. SEM micrographs (Fig. 2) indicate a significant
change in surface topography after chemical treatment. The surface of raw jute fiber was smooth
with multicellular nature, whereas rough surface morphology with fragments and better fibril
separation were observed due to alkali treatment. This phenomenon may be attributed to the
leaching of surface impurities, non-cellulosic materials, inorganic substances and wax. The
rough surface obtained after alkali treatment may improve the adhesion between fiber and matrix
Treatment duration (h)
Peak position (2)
FWHM (2)
Area (%) Amplitude (counts/s)
Crystallite size (nm)
CrI (%)
15.62 4.23 42.05 232.74 1.88 0 23.36 2.89 57.94 469.23 2.78
50.4
15.64 3.63 39.70 492.00 2.19 0.5 22.73 2.55 60.30 1063.46 3.16
53.7
15.69 3.62 39.53 387.98 2.17 4 22.11 2.59 60.46 827.59 3.11
53.6
15.67 3.42 35.34 438.33 2.33 24 22.35 2.34 64.65 1172.17 3.43
62.6
17
(a)
50 m 50 m
(b)
50 m
(c)
when used in reinforcing composite materials. After modification with polymer latex a thin
coating of polymer was observed on jute fiber surface.
Fig. 2. Surface morphologies of different jute fibers: (a) Raw jute fiber, (b) Alkali (0.5%, 24 h) treated jute fiber, (c) Alkali and polymer (0.5%, 24 h) treated jute fiber.
B.3.4. Water absorption and hydrophilicity studyof jute fiber
The water absorption study of jute fibers was done in accordance with ASTM D570-98.
The water absorption was calculated as
Water absorption (%) = [(w2 w1)/w1] x 100 (1)
Where, w1 is the initial weight of oven dried jute fiber before water absorption and w2 is the
weight of jute fiber after water absorption. Water absorption of jute fiber decreases after
chemical modification. Water absorption of untreated jute fiber is 210% but reduces to 112%
after 0.5% alkali and 0.25% polymer treatment (Table 2).
Fig. 3a. Contact angle of raw jute fiber. Fig. 3b. Contact angle of chemically treated jute fiber.
(c)
18
This result was further supported by hydrophilicity study, which was studied by contact
angle measurement. This shows that the contact angle of jute fiber increases after alkali and
polymer latex treatment (Table 2 and Fig. 3a and 3b).
Table 2. Water absorption of untreated and chemically treated jute fiber
B.3.5. Tensile properties
The tensile properties of the jute fibers were measured using Hounsfield 10K tensile
testing machine in accordance with ASTM D3822-01. The obtained results were analyzed
statistically by Weibull distribution method.
This two-parameter semi-empirical distribution is given by
( ) ( ) ( )mm xxmxf = exp1 (2) where, f(x) is the frequency distribution of the random variable x and m is a shape factor usually
referred to as Weibull modulus. When Eq. (2) is plotted a bell shaped curve results, the width of
which depends on m, as m gets larger the distribution narrows. Since here it was dealt with
tensile strength, the random variable x is defined as 0, where is the failure stress and 0 is a
normalizing parameter.
Survival probability (S), i.e., the fraction of samples that would survive at a given stress
level, can be calculated by replacing x by 0 in Eq. (2)
NaOH (wt %) Latex (v/v %) Treatment duration (h) Water absorption (%) Contact angle (degree) 0.0 0.0 0.0 210 2.0 63.9 2.8
0.25 0.00 0.5 200 1.7 69.3 2.3 0.25 0.00 4.0 192 1.9 74.7 3.2 0.25 0.00 24.0 187 2.2 76.4 6.4 0.25 0.00 48.0 180 1.5 77.7 5.6 0.5 0.00 0.5 173 2.1 80.4 4.4 0.5 0.00 4.0 170 2.3 83.7 3.8 0.5 0.00 24.0 161 1.4 86.5 5.5 0.5 0.00 48.0 160 1.6 89.2 1.6 1.0 0.00 0.5 168 2.3 92.3 4.3 1.0 0.00 4.0 155 1.8 93.7 4.6 1.0 0.00 24.0 152 1.7 95.3 5.4 1.0 0.00 48.0 148 2.1 96.2 3.4 0.5 0.25 24.0 112 1.9 103.6 4.1 0.5 0.50 24.0 108 2.2 108.1 3.7 0.5 1.00 24.0 104 1.7 110.8 5.1
19
=
000
dfS (3)
or
=
m
S0
exp
(4)
Rewriting Eq. (4) as 1/S = exp ( 0)m and taking logarithm of both sides twice yields
0lnln1lnln mmS
+=
(5) Plotting ln ln (1/S) versus ln a straight line with slope m can be obtained and from
the intercept and slope 0 value can be calculated. 0 is the stress level at which S = 1/e = 0.37. A
low value of the Weibull modulus indicates a high variability.
The tensile strength (0) of jute fiber was found to be increased after alkali treatment.
After 24 h, 0.5% alkali solution treatment, at ambient temperature, the tensile strength of jute
fiber was improved by 82% compared to that of untreated jute fiber (337 MPa) and the
elongation at break was also improved by 35% with respect to elongation at break of untreated
jute fiber (1.26%), i.e., the alkali treatment makes the fibers more flexible (Table 3a and 3b, Fig.
4a). Variation of tensile strength of jute fiber (0) with alkali treatment time is shown in Fig. 4b.
Table 3a. Tensile strength of jute fibers after alkali treatment at ambient temperature
The tensile strength at 80% probability (), i.e., the failure stress and Weibull modulus
(m) achieve a maximum value of 296 MPa and 2.1 respectively after treatment with 0.5% alkali
solution for 24 h (at ambient temperature).
Tensile strength (MPa) for different treatment duration NaOH (wt %) 0.5 h 1 h 2 h 4 h 8 h 16 h 24 h 36 h 48 h
0.25 297 320 294 302 340 354 353 400 368 0.5 374 388 429 452 481 502 610 517 403 1.0 453 525 489 413 319 340 360 303 307
20
0 10 20 30 40 50300
350
400
450
500
550
600
650
Tens
ile s
tren
gth
(MPa
)
Time(h)
Table 3b. Elongation at break of jute fiber after alkali treatment at ambient temperature
When 24 h 0.5% alkali treated jute fiber was modified with 0.5% polymer latex tensile
strength increases by 40% w.r.t. that of untreated jute fiber (Table 3c). For polymer latex treated
jute fiber, the Weibull modulus increases as tensile strength increases.
Table 3c. Tensile properties and diameter for 0.5% alkali (24 h) and polymer latex treated jute fiber
B.3.6. Durability of unmodified and modified jute fiber in cement matrix
Untreated and 0.5% alkali and 0.5% polymer latex treated jute fibers were kept in cement
matrix for 7, 28, 42, 90 days. The jute fibers were pulled out from the cement matrix after
Fig. 4a. Plot of ln ln (1/S) vs. ln for the tensile
strength of 0.5% alkali treated jute fiber.
Fig. 4b. Tensile strength (0) of 0.5% alkali treated jute
fiber at different time intervals.
Elongation at break (%) for different treatment duration NaOH (wt %) 0.5 h 1 h 2 h 4 h 8 h 16 h 24 h 36 h 48 h
0.25 1.46 1.34 1.48 1.49 1.44 1.45 1.46 1.47 1.42 0.5 1.36 1.41 1.45 1.48 1.54 1.66 1.70 1.55 1.39 1.0 1.54 1.58 1.54 1.50 1.41 1.40 1.42 1.44 1.46
Polymer latex (v/v %)
Diameter (mm) Elongation at break (%)
Tensile strength (MPa)
Weibull modulus (m) of tensile strength
0.25 0.056 0.004 1.41 396 2.39 0.5 0.060 0.016 1.69 471 3.32 1.0 0.071 0.020 1.68 435 3.36
21
0 20 40 60 80 1000.80
0.85
0.90
0.95
1.00
1.05
Nor
mal
ized
tens
ile st
reng
th
Aging time (days)
Raw jute Polymer modified jute
specified days and tensile strength was measured. Ageing test of untreated and treated jute fiber
in cement matrix shows that least degradation had occurred for 24 h, 0.5% alkali and 0.5%
polymer latex treated jute fiber (Table 4).
Table 4. Change in tensile strength of jute fiber in cement paste with time
Fig. 5 shows the relative degradation of jute fiber in terms of loss of tensile strength with
respect to aging time in days, after performing degradation study. The extent of degradation of
polymer treated jute fibers incorporated in cement paste is much lower as compared to that of
untreated raw jute. The degradation is also much slower for polymer treated jute in contrast to
raw jute.
Fig. 5. Degradation study of untreated and chemically treated jute fiber in cement paste
Tensile strength (MPa) of jute fiber in cement paste at different ageing duration
Type of jute fiber
0 day 7 days 28 days 42 days 90 days
Degradation (%) after 90 days
Untreated 335 330 311 308 275 18 Alkali and latex treated 470 469 466 464 459 2.3
22
Achievement 9 Alkali and polymer modifications of jute fiber improve
tensile strength and elongation at break about 41 and 34 % respectively.
9 Water absorption of jute fiber is reduced to 108 % from 210 % after alkali and polymer treatment.
9 Degradation study of jute fiber in cement matrices shows that the rate of degradation of treated jute fibers incorporated in cement paste is constant with time whereas in case of untreated jute fibers incorporated in cement paste degraded rapidly with time.
23
SECTION C
Fabrication and characterization of jute reinforced cement composite
24
C.1. Materials
Portland Pozzolona cement was supplied by Ambuja Cement Pvt. Ltd. Locally available
coarse aggregate (stone chips of size 0 - 20 mm) and sand (of 300 m) were used for composite
fabrication as per IS: 383-2002. Tannin, a natural polyphenolic admixture, was procured from
local market. Jute fibers of TD4 grade were collected from Gloster Jute Mill, Howrah, India.
C.2. Setting characteristics of Portland Pozzolonic cement
Standard consistency of cement means the minimum amount of water required to prepare
a plastic mix. The setting and hardening of cement is a continuous process, but two points are
distinguished for test purposes. The initial setting time is the interval between the mixing of the
cement with water and the time when the mix has lost plasticity, stiffening to a certain degree. It
marks roughly the end of the period when the wet mix can be molded into shape. The final
setting time is the point at which the set cement has acquired a sufficient firmness to resist a
certain defined pressure.Consistency, initial and final setting time of cement pastes with and
without jute fiber was measured by Vicat Apparatus according to IS: 4031.
From Tables 5a and 5b it is observed that the initial and final setting times of raw jute
fiber incorporated cement paste are higher than that of the control cement paste. It has been
reported and observed by us also that the presence of hydrophilic jute in wet cement matrix
delays the hydration reaction. This in turn delays the initial and final setting time of cement
paste. But when polymer latex modified jute fibers were incorporated into cement matrix, the
initial and final setting time was decreased than that of the raw jute fiber reinforced cement.
Treating jute with polymer latex decreases the hydrophilicity of jute which in turn do not affect
the normal setting time appreciably. Addition of organic admixture tannin to cement is also
found to delay the setting time of cement.
As the content of jute fiber in cement matrix increases, the initial and final setting time of
cement paste increases (Fig. 6a). But the setting time decreases as the polymer content increases
in cement matrix (Fig. 6b).
25
Table 5a. Influence of jute fiber on setting time of cement paste (measured by consistency method)
Sample code
Jute loading
(%)
Polymer emulsion
(%)
Standard consistency
(W/C)
W/C for setting time measurement
(% of standard consistency)
Initial setting time (min)
Final setting time (min)
Difference between initial and final
setting time (min)
Control 0 0 0.390 85 130 170 40 RJC 1 0 0.400 85 160 205 45 RJC 2 0 0.410 85 169 223 54 RJC 3 0 0.420 85 175 236 61 RJC 4 0 0.430 85 180 246 64 AJC 1 0 0.400 85 154 194 40 LJC 1 0.0625 0.400 85 152 191 39 LJC 1 0.1250 0.395 85 149 186 37 LJC 1 0.2500 0.390 85 146 182 36 LJC 1 0.5000 0.385 85 144 178 34
LTJC 1 0.1250 0.350 85 176 210 34 N.B. RJC: raw jute cement, AJC: alkali treated jute cement, LJC: alkali and polymer latex treated jute cement, LTJC: Alkali and polymer latex treated jute cement modified with tannin, W: water, C: cement. Table 5b. Influence of jute fiber on setting time of cement paste (measured by constant water method)
Sample code
Jute loading
(%)
Polymer emulsion
(%)
Standard consistency
(W/C)
W/C for setting time
measurement
Initial setting time
(min)
Final setting time
(min)
Difference between initial and final setting
time (min)
Control 0 0 0.390 0.3315 130 170 40 RJC 1 0 0.400 0.3315 151 193 42 RJC 2 0 0.410 0.3315 155 199 46 RJC 3 0 0.420 0.3315 162 213 51 RJC 4 0 0.430 0.3315 167 220 53 AJC 1 0 0.400 0.3315 151 190 39 LJC 1 0.0625 0.400 0.3315 150 188 38 LJC 1 0.1250 0.395 0.3315 147 184 37 LJC 1 0.2500 0.390 0.3315 146 182 36 LJC 1 0.5000 0.385 0.3315 143 178 35
LTJC 1 0.1250 0.350 0.3315 176 210 34 N.B. RJC: raw jute cement, AJC: alkali treated jute cement, LJC: alkali and latex treated jute cement, LTJC: Alkali and latex treated jute cement modified with tannin, W: water, C: cement.
26
C.3. Processing of unmodified and chemically modified jute fiber reinforced cement mortar
/concrete composites
The mortar mix design of cement and sand was 1:3 by weight. Untreated and chemically
treated chopped jute fibers were used as reinforcing agent in different weight percentages in
cement composite. The major problems encountered with jute fiber as a reinforcing agent in
cement matrix are its non uniform dispersion due to agglomeration of the fiber and its
hydrophilic nature. Hence to achieve a uniform dispersion of fibers in cement matrix two
different mixing procedures were followed for preparing jute fiber reinforced cement mortar
composite (JRM), viz., Process-A and Process-B.
In Process-A, for untreated jute fiber reinforced mortar (UJRM), initially the chopped
fibers were immersed for 24 h in half of the total volume of water required for mortar
preparation in a container. Next the half of the total amount of cement required was added to wet
jute in that container with constant stirring to obtain jute-cement slurry. The jute cement slurry
was then slowly poured into the pan-mixer with stirring provision and the pan-mixer was run for
2 min. Sand and rest of cement was mixed with this jute-cement slurry. The remaining amount of
water was then added and the pan-mixer was run for further 5 min. The fresh cement mortar thus
obtained was cast immediately in molds and allowed to setting.
In Process-B, equilibrium water soaked jute was used for mortar preparation. Half of the
amount of total cement required and half of the total volume of water required were then added
0 1 2 3 4125
150
175
200
225
250 Initial setting time Final setting time
Setti
ng ti
me (
min
utes
)
Jute loading (%)
0.00 0.15 0.30 0.45 0.60
120
140
160
180
Setti
ng ti
me (
min
utes
)
Initial setting time Final setting time
Polymer latex (%)
Fig. 6a. Setting time measurement of cement paste containing varying percents of jute fiber
Fig. 6b. Setting time measurement of polymer latex modified jute fiber reinforced cement paste by measuring standard
consistency
27
to the wet jute fibers with constant stirring in a pan mixer to obtain jute-cement slurry. Sand and
rest of cement were mixed with the jute-cement slurry. The remaining amount of water was then
added and the pan-mixer was run for extra 5 min. The fresh cement mortar thus obtained was
cast immediately in molds and kept for 24 h.
Polymer latex treated jute fiber reinforced mortar (LJRM) specimens were prepared by
Process-B. For LJRM fabrication, jute fibers were initially immersed in 0.5% alkali solution
maintaining a liquor ratio 1:30 (jute: alkali solution) and after 24 h excess amount of liquor,
which was not absorbed by jute, was drained out. 0.0625-0.5% polymer latex (v/v) was prepared
by adding water (which is the total water required for mortar). Half of the total volume of diluted
polymer latex and half of the amount of cement required was used to prepare jute-cement slurry.
Sand, rest of cement and remaining amount of polymer latex were mixed with the jute-cement
slurry and LJRM specimens were prepared. In Process-B the water cement ratio was calculated
to be 0.6 for both UJRM and LJRM.
Optimization of length of jute fiber in cement matrix was done by incorporating jute fiber
of 5, 10 and 20 mm lengths following Process-B.
The jute fiber reinforced concrete (JRC) samples of mix design 1:2:4 (cement: sand:
coarse aggregate, by weight) were fabricated by following Processe-B. During the fabrication of
JRC by Process-B, a natural water reducing polyphenolic admixture (tannin) was used. A tannin
polymer mixture was prepared by adding 0.25% tannin powder (w.r.t. cement weight) in total
amount of polymer emulsion. Half of the total volume of this mixture and half of the amount of
cement required were used to prepare jute-cement slurry. This jute cement slurry was then
poured into the concrete-mixer containing sand and stone chips. The concrete-mixer was run for
5 min for achieving proper mixing of the components. The fresh chemically treated jute fiber
reinforced concrete thus obtained was cast immediately in molds and kept for 24 h. The addition
of tannin during the preparation of jute cement concrete reduces water cement ratio to 0.50-0.52
in contrast to 0.6 and the slump value of the prepared concrete mix was 75 10 mm. In JRC
specimens the incorporated jute fibers were of 5 mm length. Fig. 7 shows the schematic flow
diagram of chemically treated jute fiber reinforced concrete fabrication by Process-B.
All the specimens were demolded after 24 h of casting and water cured for 28, 42 and 90
days respectively. At the specified date they were removed from water, surface dried and tested.
28
Each test result represented the mean of at least five specimens. Each mix series is coded. For
example, the code A1UJRM/B1UJRM refers to Process-A (B stands for Process-B), 1% (w. r. t.
the weight of cement) untreated jute fiber content by weight (UJ for untreated jute, LJ for alkali
and polymer latex treated jute); R stands for reinforced, M stands for mortar. The code B1UJRC
refers to Process-B, (C refers to concrete). Other letters in the code designate the same as
described above.
Demolding and water cured
Chemically modified jute fiber reinforced concrete
Vibration casting in a steel mold ld
Fine aggregate, coarse aggregate, rest amount of cement
Blender
Chemically modified jute fiber
Chemically modified jute fiber-cement slurry
Chemically modified jute fiber containing green concrete
Freshly prepared chemically modified jute fiber reinforced green concrete
Half of the total volume of 0.125% (v/v) polymer latex
Cement (50% of total) cemen
Untreated jute fiber
Blender
Concrete mixer Mixture of 0.25% tannin powder (w.r.t. cement weight) and remaining amount of polymer latex
Alkali treated jute fiber
Fig. 7. Schematic flow diagram of chemically treated jute fiber reinforced concrete fabrication (by Process-B)
29
C.4. Physical and mechanical properties of unmodified and modified jute fiber reinforced cement mortar
C.4.1 Bulk density
Increase in jute fiber content significantly decreases the bulk density of the mortar. The
reason might be the replacement of cement mortar (dense materials) by light jute fiber. The
apparent bulk density of the jute cement mortar made by Process-A is lower than that of the
mortar made by Process-B with the same amount of raw jute (1%) (Table 6a). The variation of
apparent bulk density of polymer modified jute fiber reinforced cement mortar is depended upon
loading of jute fiber and polymer latex, which is added to prepare polymer latex modified cement
mortar. From Table 6b it is found that the bulk density of modified mortar increases with
increase in polymer latex.
Table 6a. Physical and mechanical properties of unmodified jute fiber reinforced cement mortar prepared by Process-A/Process-B
C.4.2. Flow table value
The workability of control and jute reinforced mortar were measured by flow table index
test according to IS: 4031. In our investigation flow table value was decreased with increase in
jute fiber loading for the preparation of jute cement mortar at constant water cement ratio. From
Table 6a it can be observed that jute cement mortar made by Process-B shows good flow value
than that made by Process-A, with same jute content (1%). The effectiveness of polymer latex on
flowability of jute fiber reinforced cement mortar depends upon its concentration. From the
Table 6b it is found that the flow table value is increased with increase in polymer latex
Compressive strength (MPa) after Flexural strength (MPa) after Sample code
Flow table Value (mm)
Bulk density (Kg/m3) 28 days curing
42 days curing
90 days curing
28 days curing
42 days curing
90 days curing
Control 155 5 2283 10 28.3 2.3 29.8 2.4 34.5 2.1 7.1 0.3 7.2 0.3 7.4 0.3 A1UJRM 127 9 2100 30 25.8 1.5 26.8 1.5 29.8 1.6 6.4 0.3 7.0 0.3 7.7 0.4 A2UJRM 115 7 2100 80 24.0 1.5 26.0 1.5 28.0 1.6 6.2 0.3 6.5 0.2 7.1 0.2 A3UJRM 110 6 1900 40 18.2 1.5 21.0 1.5 21.5 1.5 4.7 0.3 5.0 0.3 6.3 0.3 A4UJRM 110 8 1800 50 15.4 1.6 16.4 1.5 19.7 1.5 1.6 0.3 2.5 0.3 3.9 0.3 B1UJRM 156 6 2270 10 30.8 1.5 32.1 1.5 35.8 1.7 7.6 0.3 8.5 0.3 10.0 0.5 B2UJRM 157 8 2220 50 30.1 1.6 31.5 1.6 35.0 1.5 7.2 0.3 8.0 0.4 9.0 0.5 B3UJRM 159 9 2190 10 20.0 1.6 21.5 1.5 25.0 1.6 6.6 0.4 7.0 0.4 7.5 0.4 B4UJRM 161 8 2100 10 17.0 1.4 18.0 1.6 19.4 1.6 6.1 0.3 6.4 0.4 6.7 0.4
30
concentration at same W/C ratio. Increase in polymer latex concentration decreases the water
requirement in cement mortar preparation to produce constant satisfactory workable mortar.
Addition of 0.5 % polymer latex to the cement mortar decreases the W/C ratio 0.6 to 0.54 and
maintains the flow table value of 155 2 mm.
Table 6b. Physical properties of polymer latex modified jute fiber reinforced cement mortar fabricated by Process-B
C.4.3. Microstructure analysis of jute fiber reinforced mortar composite
The fracture surface topography of the cementitious matrix reinforced with jute fibers
was analyzed using SEM after mechanical testing of mortar samples. In Fig. 8 it can be observed
that a homogeneous dispersion of jute fibers in cementitious matrix at lower jute content and
considerable amounts of these fibers are well attached to the matrix. However, the higher amount
of fibers showed inhomogeneous dispersion in the cementitious matrix and poor anchoring,
which created bulk flaw and stress was concentrated on that flaw and crashed at lower stress.
C.4.4. Compressive strength
Compressive strength of JRM cubic specimens of dimension 70.6 mm x 70.6 mm x 70.6
mm was measured by a 1000 kN Hydraulic Universal Testing machine as per IS: 516.
Compressive strength is a function of fiber loading, fiber length and curing time and it also
depends upon the process by which composites were made (Table 6a). The compressive strength
decreases with increases in fiber loading and length. Optimal compressive strength of jute
Sample code Polymer latex (%)
Water/Cement ratio
Flow table value (mm)
Bulk density (kg/m3)
Control - 0.60 155 5 2283 12 B1LJRM 0.063 0.60 157 8 2285 12 B1LJRM 0.125 0.60 161 6 2288 15 B1LJRM 0.250 0.60 164 5 2291 14 B1LJRM 0.500 0.60 167 8 2298 13 B1LJRM 0.063 0.60 157 8 2285 12 B1LJRM 0.125 0.58 156 8 2290 11 B1LJRM 0.250 0.56 156 8 2296 14 B1LJRM 0.500 0.54 151 7 2301 12 B2LJRM 0.125 0.60 162 8 2269 12 B3LJRM 0.125 0.60 164 9 2259 10 B2LJRM 0.125 0.58 157 9 2272 11 B3LJRM 0.125 0.58 156 5 2263 14
31
cement mortar was obtained with shorter fiber length of 5 mm (Fig. 9a). Increase in length of the
fiber increases fiber agglomeration in composite specimens. The fiber ball makes the specimen
porous and lead to obtain lower strength. The maximum compressive strength was achieved by 5
mm 1% jute fiber containing mortar fabricated by Process-B.
0 1 2 3 4
15
20
25
30
35
Com
pres
sive s
tren
gth
(MPa
)
Jute loading (%)
5 (mm) jute 10 (mm) jute 20 (mm) jute
20 30 40 50 60 70 80 9024
27
30
33
36
39
42
Com
pres
sive s
tren
gth
(MPa
)
Curing time (Days)
Reference Process-A Process-B
Fig. 9a. Compressive strength of mortar cubes
containing different lengths and different loadings of jute fiber
Fig. 9b. Compressive strength of 28, 42 and 90 days water cured mortar cube samples fabricated by different
processes
A comparative study of compressive strength of raw jute and alkali polymer latex treated
jute cement mortar containing 5 mm 1% jute, cured for different curing times is shown in Tables
6a and c. The compressive strength of jute fiber reinforced cement mortar prepared by different
processes continues to increase with increase in curing days (Fig. 9b).
Fig. 8a. Fracture surface of control cement mortar
Fig. 8b. Fracture surface of 1% jute fiber reinforced cement
Fig. 8c. Fracture surface of 4% jute fiber reinforced cement
1mm 1mm 1 mm
32
Table 6c. Mechanical properties of jute fiber reinforced polymer latex modified cement mortar fabricated by Process-B
N.B. *Maximum standard deviation for compressive strength 1.8, **Maximum standard deviation for flexural strength 0.6.
From Fig. 9c it is found that initially the compressive strength of modified cement mortar
improves with increase in polymer latex content and reaches a maximum at 0.125 % polymer
latex concentration; it continues to turn down with increase in polymer latex. Thus optimum
compressive strength (38.4 MPa) of cement mortar (90 days cured) was achieved by reinforcing
5 mm 1% jute fiber modified by 0.125% polymer latex. Fig. 9d shows superior compressive
strength of 0.125 % polymer latex modified jute fiber reinforced cement mortar with lower W/C
ratio.
Compressive strength* (MPa) after Flexural strength** (MPa) after Sample code Polymer emulsion
(%)
W/C ratio 28 days
curing 42 days curing
90 days curing
28 days curing
42 days curing
90 days curing
Control - 0.60 28.3 29.8 34.5 7.1 7.2 7.4 B1LJRM 0.063 0.60 34.4 35.9 37.3 8.5 10.2 11.6 B1LJRM 0.125 0.60 35.4 36.2 37.9 9.1 10.6 12.8 B1LJRM 0.250 0.60 28.2 31.6 33.7 8.0 9.7 11.1 B1LJRM 0.500 0.60 27.2 29.5 32.3 7.7 8.3 9.4 B1LJRM 0.063 0.60 34.4 35.9 37.3 8.5 10.2 11.6 B1LJRM 0.125 0.58 35.5 37.1 38.4 9.3 10.8 13.8 B1LJRM 0.250 0.56 29.1 32.0 34.2 8.1 9.9 11.3 B1LJRM 0.500 0.54 27.7 30.0 33.0 7.8 8.3 9.6 B2LJRM 0.125 0.60 24.2 26.4 29.1 7.1 7.5 7.8 B3LJRM 0.125 0.60 17.5 20.0 22.9 6.3 6.6 6.9 B2LJRM 0.125 0.58 25.0 27.1 30.1 7.3 7.7 8.0 B3LJRM 0.125 0.58 18.0 20.9 23.5 6.4 6.9 7.3
33
C.4.5. Flexural strength
The flexural tests of the fabricated mortar bar test specimens of dimensions 110 mm x 20
mm x 20 mm (length x width x thickness) were carried out on the same testing system using a
four point bending configuration, under a span of 60 mm according IS: 4332. The correlation
between flexural strength and the major parameters of jute cement mortar bars at different curing
times are shown in Tables 6a and 6c. During the test it was observed that at the beginning of
loading, the behavior is elastic in nature until the first crack was generated and then the failure of
specimen was gradual. The specimen did not break into pieces (i.e., retain its integrity) after
occurrence of excessive vertical cracks, compared with the control mortar having no fiber.
Flexural strength is gradually decreased with increase in fiber content in both processes (Table
6a). The flexural strength of 1% jute loaded and 90 days cured cement mortar made by Process-
B was 35 % superior to control mortar. For both processes, improvement of flexural strength of
cement mortar (with 1% jute and without jute reinforced) with the curing time are shown in Fig.
10a and same observation was found in the case jute fiber reinforced polymer latex modified
mortar with different W/C ratio (Fig. 10b). A comparative study of flexural strength of raw jute
and alkali-polymer latex treated jute cement mortar containing 1% jute, cured for different curing
time is shown in Table 6a and 6c.
0.0 0.1 0.2 0.3 0.4 0.526
28
30
32
34
36
Compressive strength Flexural strength
Polymer latex (%)Com
pres
sive s
tren
gth
(MPa
)
7.0
7.5
8.0
8.5
9.0
9.5 Flexural strength (MPa)
0 20 40 60 80 1007
14
21
28
35
42
Com
pres
sive s
tren
gth
(MPa
)
Curing time (days)
control mortar 0.125S60 - 1 0.125S58 - 1
Fig. 9c. Compressive and flexural strength of jute reinforced (1%) polymer modified cement mortar (28 days cured) vs.
polymer latex percent
Fig. 9d. Compressive strength of 0.125% latex modified mortar containing different W/C ratio with
curing time
34
30 45 60 75 90
6
7
8
9
10
11Fl
exur
al st
reng
th (M
Pa)
Curing time (Days)
Reference Process-A Process-B
0 20 40 60 80 100468
101214
Flex
ural
stre
ngth
(MPa
)
Curing time (days)
Control mortar 0.125S60-1 0.125S58-1
Fig. 10a. Flexural strength of mortar samples fabricated by different processes after 28, 42 and 90
days curing
Fig. 10b. Flexural strength of 0.125% latex modified mortar containing different W/C ratio with curing time
C.4.6. Relation between density ratio and strength ratio
The wet and dry density of control cement mortar and jute fiber reinforced cement mortar
were measured according to ASTM C 948, 1981. In Fig. 11 it is shown that wet density to dry
density ratio of jute incorporated polymer modified cement mortar (0.6 W/C) possesses a gradual
downward trend with increase in polymer latex content and an upward trend of flexural strength
to compressive strength ratio. The left hand inset graph of Fig. 11 shows that both wet and dry
densities of polymer modified cement mortar increase with increase in polymer latex content but
the difference between wet density and dry density becomes smaller with increase in polymer
latex content showing a decrease of density ratio. The right hand inset figure of Fig. 11 shows
that initially compressive and flexural strengths increase with increase in polymer latex
concentration and reaches a maximum at 0.125% polymer latex. So it can be assumed from the
resulting trend of Fig. 11 that the extent of decrease of flexural strength is lower than that of the
compressive strength with increase in polymer concentration after attaining the maximum value
at a particular polymer latex concentration.
35
0.0 0.1 0.2 0.3 0.4 0.5
1.07
1.08
1.09
1.10
1.11
0.0 0.1 0.2 0.3 0.4 0.526
28
30
32
34
36
Compressive strength Flexural strength
Polymer latex (%)Com
pres
sive
stre
ngth
(MPa
)
7.0
7.5
8.0
8.5
9.0
9.5 Flexural strength (MPa)0.0 0.1 0.2 0.3 0.4 0.5
2.275
2.280
2.285
2.290
2.295
2.300
Wet density Dry density
Polymer latex (%)
Wet
den
sity
(g/c
c)
2.082.102.122.142.162.182.20
Dry density (g/cc)
density ratio strength ratio
Polymer latex (%)
Wet
den
sity
and
dry
den
sity
rat
io
0.247
0.260
0.273
0.286
0.299
0.312 Flexural and compressive
strength ratio
C.4.7. Extensibility
Extensibility is an important property for cement composite. Extension not only reflects
the impact ductility and fracture enhancements, but also is an assurance of the safety and
integrity of a structural element prior to its complete failure. Extension in plain cement mortar
leads to rapid crack growth. When the fibers were present in cement mortar, the cracks could not
extend without stretching and debonding the fibers during the bending of a composite beam. It
can be seen that the process parameter and fiber factor together play a significant role in
enhancing the extension of jute cement mortar. Extensibility increases gradually with increase in
fiber loading into cement mortar composite as shown in Fig. 12a. The maximum elongation was
obtained for the Process-B, which was about four times more than the control mortar by
incorporation of 4% jute into cement mortar. When alkali-polymer latex treated jute fibers were
used to make composite, elongation of mortar was increased. This is due to an increase in
elongation at break after chemical treatment of jute fiber, and that effect was reflected into the
composite also (Fig. 12b).
Fig. 11. Density and strength ratio of latex modified cement mortar with latex percent
36
0 1 2 30.5
1.0
1.5
2.0
2.5
Elo
ngat
ion
(mm
)
Jute loading (%)
Raw jute mortar made by process-B Alkali treated jute mortar Alkali polymer latex treated
jute mortar made by process-B
Fig. 12a. Load deflection curve for mortar containing different percent of jute
Fig. 12b. A comparative study of elongation vs. loading of raw jute, alkali treated jute, alkali and
polymer latex treated jute mortar
C.5. Physical and mechanical properties of unmodified and modified jute fiber reinforced concrete
C.5.1. Slump test
The workability of the fresh concrete was measured by slump test according to IS: 1199.
Slump value, an index of workability of fresh concrete, was adversely affected by jute content. In
Process-B, since water soaked fiber was used there was no further water absorption by jute from
concrete mix and this makes the fresh concrete to have a good workability. The workability of
reinforced concrete was affected by chemical modification of jute fiber. Chemically modified
jute fiber reinforced concrete has higher slump value compared to that of untreated jute fiber
reinforced concrete with same water cement ratio (Table 7).
C.5.2. Specific gravity
Specific gravity of the concrete was measured according to ASTM C948-01. The
incorporation of jute fiber into the cement-concrete matrix decreases the specific gravity of the
composite, because the specific gravity of jute fiber (1.6 g/cm3) is much smaller than that of
reference concrete (2.43 g/cm3). From Table 7, it can be seen that as the jute fiber loading
increases specific gravity of the composites decreases.
37
Table 7. Physical and mechanical properties of JFRC composites
a w.r.t. the weight of cement, b Mean standard deviation, B refers to process-B; 0.5,1,2,3,4 are jute loading percent w.r.t. weight of cement; UJ refers to Untreated Jute; LJ refers to alkali and polymer Latex modified Jute; LTJ refers to alkali and polymer latex and tannin modified jute; RC refers to Reinforced Concrete. C.5.3. Microstructure analysis of jute fiber reinforced concrete composite
The fracture surface topography of the cementitious matrix reinforced with jute fibers
was analysed using optical microscope after mechanical testing of samples. Fig. 13 shows the
microstructure of concrete with and without jute fiber reinforcement.
Mix code Fibera (wt %)
W/C ratio
Curing (days)
S.G.b(Kg/m3)
Slump valueb
Compressive strengthb (MPa)
Flexural strengthb (MPa)
Control 0.0 0.6 28 27.5 1.5 2.6 0.2 Control 0.0 0.6 42 29.0 2.0 2.7 0.3 Control 0.0 0.6 90
2545 55 65 5
30.0 1.0 2.7 0.4 B0.5UJRC 0.5 0.6 28 31.0 1.0 2.7 0.1 B0.5UJRC 0.5 0.6 42 32.5 1.5 2.8 0.2 B0.5UJRC 0.5 0.6 90
2544 58 65 4
34.0 2.0 2.9 0.3 B1UJRC 1.0 0.6 28 32.0 1.5 2.9 0.2 B1UJRC 1.0 0.6 42 34.0 2.0 3.0 0.2 B1UJRC 1.0 0.6 90
2543 60 70 5
37.5 2.5 3.2 0.4 B2UJRC 2.0 0.6 28 29.0 2.0 2.2 0.3 B2UJRC 2.0 0.6 42 31.0 2.5 2.3 0.1 B2UJRC 2.0 0.6 90
2538 57 72 3
33.5 1.5 2.5 0.2 B3UJRC 3.0 0.6 28 26.5 1.5 2.2 0.2 B3UJRC 3.0 0.6 42 28.0 1.0 2.1 0.3 B4UJRC 3.0 0.6 90
2533 61 75 6
31.0 1.0 1.8 0.1 B4UJRC 4.0 0.6 28 22.5 1.0 1.6 0.2 B4UJRC 4.0 0.6 42 24.0 1.5 1.8 0.3 B4UJRC 4.0 0.6 90
2528 54 78 5
26.5 2.0 1.9 0.4 B1LJRC 1.0 0.6 28 37.0 1.5 3.8 0.2 B1LJRC 1.0 0.6 42 39.0 2.0 4.0 0.3 B1LJRC 1.0 0.6 90
2544 52 75 4
42.0 1.3 4.2 0.1 B1LTJRC 1.0 0.5 28 2546 42 80 5 43.0 1.2 4.1 0.2 B1LTJRC 1.0 0.5 42 44.0 1.5 4.3 0.1 B1LTJRC 1.0 0.5 90 48.0 1.2 4.5 0.3
38
Fig. 13a Microstructure of reference cement concrete
Fig. 13b Untreated jute fiber reinforeced cement concrete
Fig. 13c Homogenious dispersion of treated jute fiber reinforced cement
concrete
C.5.4. Compressive strength
Compressive strength of jute cement concrete cubes [(100x100x100) m3] was measured
by universal testing machine according to IS: 516, 2004. The strength of composites increases
with low fiber content within the range 0.5 1.0% compared to reference concrete and
maximum strength was achieved with 1% fiber loading, irrespective of the fiber surface
modification and cuing days (Table 7). But, as the fiber content exceeds the value of 1%
compressive strength of composite decreases significantly. The compressive strength of JRC
continues to increase with cuing days, which is irrelevant with fiber loading percent. For 1UJRC
fabricated by Process-B, compressive strength increases 17% at an age of 90 days curing w.r.t. to
that of the 28 days cured composites (Table 7). From Table 7, it is observed that LJRC achieves
higher compressive strength than that of UJRC composites, both having 1% fiber content. The
compressive strength is further increased when tannin was used as admixture during fabrication
of concrete. Thus optimum compressive strength (60 % increment w.r.t. reference concrete) was
obtained at 90 days cured, 1% chemically modified jute fiber reinforced tannin modified
concrete composites, fabricated by Process-B. During compressive failure experiment, there was
a catastrophic destruction of the composites, without jute fiber, after crack initiation. But in the
case of jute fiber reinforced cubes, a dampening effect was observed.
C.5.5. Flexural strength
Four point bending flexural strength of the fabricated composites [(100x100x500) m3]
was measured by universal testing machine according to IS: 516, 2004. The four point bending
strength of the JRC specimens increased initially with an increase in jute fiber content and the
39
maximum strength was achieved at 1% fiber loading (Table 7). During bending test, when a
crack was generated in the matrix, the randomly distributed jute fibers provided a bridging effect
to the matrix. At this portion of the tensioned composite all the stresses were transferred from the
matrix to the fiber and may be this phenomenon is responsible for carrying the increased loads.
A further increase in fiber content shows a reduction in the flexural strength and at 4% fiber
loading, the strength reduces to 1.6-1.9 MPa. The flexural strength increases with increasing
curing days. Optimum flexural strength (73% increment w.r.t. reference concrete) was obtained
at 90 days cured, 1% chemically modified jute fiber reinforced tannin modified concrete
composites, fabricated by Process-B.
40
Achievement 9 Technique of short jute fiber (optimum length: 5 mm)
dispersion in concrete is developed. 9 Maximum compressive and flexural strength is achieved
with optimized 1 wt% jute fiber loading in cement composite, i.e., about 4 kg jute fiber per one cubic meter concrete and 5.5 kg jute fiber per one cubic meter cement mortar.
9 Workability of jute fiber incorporated wet concrete mix is improved by using tannin admixture.
9 Compressive and flexural strengths of chemically treated jute fiber reinforced cement concrete are improved by 60 and 66% respectively than that of the concrete without jute fiber reinforcement.
9 Compressive and flexural strengths of chemically treated jute fiber reinforced cement mortar are improved by 11 and 86 % respectively than that of the mortar without jute.
41
SECTION D
Industrial field trial for product development
42
D.1. Identification of products
The identified areas of jute fiber reinforced cement products in this project are:
1) Jute fiber reinforced cement concrete for precast non-pressure (NP) sewerage pipes.
2) Jute fiber reinforced cement concrete for prestressed electric poles.
3) Jute fiber reinforced precast cement concrete for pavers block.
4) Jute fiber reinforced precast cement fly ash roofing sheet
D.2. Prototype development of jute fiber reinforced concrete pipe
D.2.1. Preparation of concrete for pipe fabrication
According to IS 458, 35 M graded concrete is required for fabrication of NP pipe. The
calculated mix design to prepare 35 M concrete is cement: sand: stone chips :: 1: 1.5: 2.7,
however, here stone chips of two different sizes (20 and 12.5 mm) were used in 70: 30 ratio. The
water cement ratio for concrete preparation was 0.4 - 0.42 and the slump value was 25 5 mm.
For each set of concrete composites 1% jute fiber was incorporated.
D.2.1.1. Characterization of lab based concrete composites required for pipe fabrication
No noticeable change has been observed in physical properties of the concrete made for
pipe fabrication shown in Table 8a. From the Table 8b it is observed that maximum mechanical
strength (compressive strength: 60.7 MPa and flexural strength: 6 MPa) was obtained by
incorporating 1% chemically treated jute fiber in tannin modified concrete.
Table 8a. Physical properties of lab based concrete composites (cured for 28 days) for pipe fabrication
Sample W/C ratio
Type of jute
Bulk density
Water absorption (%)
Apparent porosity (%)
Control 0.4 - 2635 57 4.5 0.5 11.4 1.2 Raw jute concrete 0.42 Untreated 2520 36 7.1 1.5 16.8 3.5 Chemically treated jute concrete
0.42 Alkali and latex treated
2597 36 6.3 0.8 15.5 1.9
Chemically treated jute concrete modified with tannin
0.4 Alkali and latex treated
2588 65 5.0 1.3 12.2 2.9
Table 8b. Mechanical properties of lab based concrete composites for pipe fabrication
Compressive strength(MPa) Flexural strength(MPa) Sample 7 days 14 days 28 days 7 days 14 days 28 days
Control 31.0 1.4 44.7 1.5 48.7 2.3 4.6 0.2 5.4 0.3 5.4 0.2 Raw jute concrete 24.5 2.1 49.7 0.6 51.7 1.5 4.2 0.2 5.0 0.1 5.8 0.3 Chemically treated jute concrete 26.0 1.4 51.7 1.0 54.3 1.6 3.7 0.1 4.1 0.1 5.7 0.2 Chemically treated jute concrete modified with tannin
21.5 4.9 51.7 4.0 60.7 1.2 4.5 0.2 5.5 0.3 5.9 0.3
43
D.2.2. Fabrication of jute fiber reinforced concrete pipe (NP3)
We collaborated with a local precast pipe manufacturing company M/S Rural Concreting
Company of Ghatal Pvt. Ltd., West Midnapur District, West Bengal. This company has all
facilities of manufacturing and testing of precast concrete pipes of different diameters. We
visited the company and fabricated jute fiber reinforced cement concrete pipes in this unit with
our mix design formulation and process. Fig.14 shows schematics of process steps followed
during the actual fabrication of jute reinforced concrete pipes.
Chemical modification of jute fiber
Mixing of cement with modified jute fiber
Jute cement slurry
Addition of jute cement slurry into mixer
Mixing Fresh jute-concrete mix
Steel cage into pipe mold
Casting of concrete pipe Prepared jute-concrete pipe
Fig. 14. Fabrication of chemically modified jute fiber reinforced precast concrete pipe
44
(a) (b) (c)
D.2.3. Fabricated concrete pipes with and without modified jute fiber reinforcement
Three different concrete sewerage pipes were made with the mix design which is
developed in this research. Fig. 15a shows the concrete sewerage pipes without any jute fiber
reinforcement. Jute fiber reinforced concrete sewerage pipes is shown in Fig 15b, and Fig. 15c
shows concrete sewerage pipes fabricated by chemically modified jute fiber reinforcement.
Fig. 15. (a) Pipes without jute fiber reinforcement, (b) pipes with untreated jute fiber reinforcement, (c) pipes with chemically modified jute fiber reinforcement
D.2.4. Standard testing of manufactured jute fiber reinforced concrete pipes
There are two standard tests of concrete sewerage pipes. The first one is hydrostatic test
of concrete sewerage pipe and second one is the three edge bearing test. Both of these tests were
performed in M/S Rural Concreting Company of Ghatal Pvt. Ltd. Fig.16a and 16b show the
testing of concrete sewerage pipes.
Fig. 16. (a) Hydrostatic testing of pipes, (b)Three edge bearing test of pipes.
Tables 9a and 9b show that jute fiber reinforced precast concrete pipe achieved better
properties than that of the standard pipe. The chemically modified jute fiber reinforced NP3
45
concrete pipe achieves higher strength than that of conventional NP4 concrete pipe by
incorporating only 20.5 kg of steel cage instead of 29.9 kg. Thus, the chemically modified jute
fiber reinforced NP3 concrete pipe is cost effective as well as strong.
Table 9a. Comparative study of the properties of modified jute fiber reinforced precast concrete pipes (PJRCP) with standard pipe of class NP2
Property Properties of concrete pipe (IS 458)
Properties of PJRCP
Remarks
Diameter (mm) 300.0 300.0 - Length (m) 2.5 2.5 -
Thickness (mm) 30.0 30.0 -
Load to produce 0.25 mm crack
(KN/linear meter) 13.5 14.0
Jute fiber reinforcement in concrete pipe leads to 3.4% increment in load required to produce 0.25 mm crack.
Strength of three
edge bearing
test Ultimate load (KN/linear meter) 20.2 21.9
Jute fiber reinforcement in concrete pipe leads to 8.4% increment in ultimate load.
Time (s) for holding water during hydrostatic test at 0.07
MPa pressure 150 186
Pressure was gradually raised up to 0.07 MPa and held for 186 s. No formation of water beads or leakage was found on the surface of pipe.
Table 9b. Comparative study of chemically treated jute fiber reinforced modified concrete pipe with standards
Properties Specifications and properties of NP3 concrete pipe (IS:
458)
Specifications and properties of NP3 concrete pipe (our pipe without jute
fiber)
Specifications and properties of our
NP3 pipe reinforced with chemically modified jute
Specifications and properties of NP4 concrete pipe (IS:
458)
Diameter (mm) 600 600 600 600 Length (m) 2.5 2.5 2.5 2.5 Thickness (mm) (IS 458) 85 85 85 85 Grade of concrete 35 M 35 M 35 M 35 M Amount of steel (Kg/pipe) 20.5 20.5 20.5 29.9 Average Load to produce 0.25 mm crack (kN) 71.9 100 3.5 154.5 3.4 115.8
Average Load to produce 0.25 mm crack (kN/linear meter) 28.7 33.3 1.6 61.8 1.4 46.3
Average Ultimate breaking load (kN) 107.8 -- 247.1 5.6 173.5
Average Ultimate breaking Load (kN / linear meter) 43.1 -- 98.9 2.2 69.4
46
D.3. Prototype development of jute fiber reinforced concrete electric pole
D.3.1. Preparation of concrete composites for pole fabrication
According to IS 1678, 45 M graded concrete is required for fabrication of pole. The
calculated mix design to prepare 45 M concrete is cement: sand: stone chips (12.5 mm) :: 1: 1: 2.
The cement used for pole preparation is OPC (Ambuja) of 43 grade. The water cement ratio for
concrete preparation was 0.32-0.34. For each set of concrete composites 1% jute fiber was
incorporated.
D.3.1.1. Physical characterization of ordinary portland cement (OPC)
Consistency, initial and final setting times of cement pastes with and without jute fiber
was measured by Vicat Apparatus according to IS: 4031.
From Table 10 it is observed that the initial and final setting times of raw jute fiber
reinforced cement paste rise from the control cement paste.
Table 10. Setting time of ordinary Portland cement paste
N.B. RJC: raw jute cement, AJC: alkali treated jute cement, LJC: alkali and latex treated jute cement, LTJC: Alkali and latex treated jute cement modified with tannin.
When polymer latex modified jute fibers were incorporated into cement matrix, the initial
and final setting time was decreased than that of the raw jute fiber reinforced cement. But
addition of organic admixture (tannin) delays the setting time of cement paste. As the jute fiber
percent in cement matrix increases, the initial and final setting times of cement paste increase.
D.3.1.2. Characterization of concrete for pole fabrication From Tables 11a and 11b it can be observed that maximum mechanical strength
(compressive strength: 81 MPa and flexural strength: 8 MPa) was obtained by incorporating 1%
chemically treated jute fiber in tannin modified concrete.
Sample code
Jute loading
(%)
Polymer emulsion
(%)
Amount of water/400g cement(ml)
Standard consistency
(W/C)
Initial setting time (min.)
Final setting time
(min)
Control 0 0.000 124.5 0.31125 172 252 RJC 1 0.000 129.0 0.32250 196 280 RJC 2 0.000 133.5 0.33375 205 295 RJC 3 0.000 143.5 0.35875 225 340 RJC 4 0.000 172.0 0.43000 -- 353 LJC 1 0.125 133.0 0.33250 192 288
LTJC 1 0.125 124.5 0.31125 335 415
47
Table 11a. Physical properties of lab based concrete composites (cured for 28 days) for pole fabrication
Table 11b. Mechanical properties of lab based concrete composites for pole fabrication
D.3.2. Fabrication of jute fiber reinforced prestressed concrete electric pole
We collaborated with a local prestressed concrete pole manufacturing company, M/S HB
Housing industries, West Midnapur District, West Bengal. This company has all facilities of
manufacturing and testing of prestressed concrete poles. We visited the company and fabricated
few jute fiber reinforced concrete poles of 6 m length with our mix design formulation and
process. Fig. 17 shows the photographs of different process steps followed during the actual
fabrication of jute reinforced concrete poles.
Sample W/C ratio Type of jute Bulk density
Water absorption (%)
Apparent porosity (%)
Control 0.32 - 2566 25 4.4 0.4 10.9 1.1 Raw jute concrete 0.34 Untreated 2555 22 5.8 0.5 14.1 1.1 Chemically treated jute concrete 0.34
Alkali and latex treated 2576 13 5.5 0.3 13.5 0.6
Chemically treated jute concrete modified with tannin 0.32
Alkali and latex treated 2587 29 4.8 0.4 11.9 1.1
Compressive strength (MPa) Flexural strength (MPa) Sample 7 days 14 days 28 days 7 days 14 days 28 days
Control 57.0 1.5 63.3 3.8 64.1 4.0 4.9 0.1 5.9 0.1 6.4 0.2 Raw jute concrete 46.0 4.1 60.6 3.5 68.3 3.5 4.2 0.2 6.2 0.2 6.6 0.3 Chemically treated jute concrete 52.0 4.6 59.0 4.4 72.3 2.5 5.2 0.2 7.0 0.1 7.0 0.2 Chemically treated jute concrete modified with tannin 32.0 2.1 67.6 5.6 81.0 1.2 6.1 0.1 7.6 0.2 8.0 0.3
48
Fig. 17. Fabrication of chemically modified jute fiber reinforced prestressed concrete pole
D.3.3. Fabricated concrete poles with modified jute fiber reinforcement
The two concrete electric poles reinforced with chemically modified jute fiber were
fabricated in the prestressed concrete pole manufacturing company, M/S HB Housing industries
and those are shown in Fig. 18.
Fig. 18. Chemically modified jute fiber reinforced prestressed concrete pole
49
D.3.4. Standard testing of fabricated jute fiber reinforced concrete pole
The standard test of concrete electric pole is cantilever test. This test was performed in
the prestressed concrete pole manufacturing company, M/S HB Housing industries. Fig. 19a
shows the cantilever test of chemically modified jute fiber reinforced concrete electric pole and
Fig. 19b shows that the maximum flexibility before failure of concrete pole.
Fig. 19a. Cantilever testing of modified jute fiber
reinforced concrete electric pole Fig.19b. Maximum flexibility before failure of modified jute fiber reinforced concrete electric
pole
Table 12 shows that jute fiber reinforced prestressed concrete pole achieved better
mechanical properties than that of the standard pole. The chemically modified jute fiber
reinforced concrete pole shows higher deflection property than that of conventional concrete
pole. Thus, the chemically modified jute fiber reinforced concrete pole can be used in coastal
areas.
Table 12. Comparative study of chemically treated jute fiber reinforced modified concrete pole with standard
Standard values of concrete pole (IS ; 1678, 1998)
Chemically modified jute fiber reinforced concrete pole (our product)
Load (kg) Ultimate load (%)
Deflection (mm)
Load (kg) Ultimate load (%)
Deflection (mm)
200 40 50 200 40 39 250 50 62 250 50 56 300 60 75 300 60 66 350 70 90 350 70 83 400 80 110 400 80 103 425 85 125 425 85 125 450 90 145 450 90 143 475 95 155 475 95 164 500 100 167 500 100 199
Ultimate load 600 -- Ultimate load 620 525
50
D.4. Prototype development of jute fiber reinforced concrete pavers block
D.4.1. Fabrication of jute fiber reinforced concrete pavers block
According to IS 15658 for fabrication of concrete pavers 35 M graded concrete is
required. The mix design of concrete paver is cement: sand: stone chips :: 1: 3: 4. Here the size
of stone chips used was 3-6 mm. The water cement ratio for concrete paver preparation was 0.2.
For each set of concrete composite 1% jute fiber was incorporated.
For prototype fabrication of concrete pavers blocks, we collaborated with a local precast
pipe manufacturing company M/S Rural Concreting Company of Ghatal Pvt. Ltd., West
Midnapur District, West Bengal. This company has all facilities of manufacturing of precast
concrete paver blocks. We visited the company and fabricated jute fiber reinforced concrete
paver blocks in this unit with our mix design formulation and process.
Fig. 20 shows few photographs of process steps followed during the actual fabrication of
jute reinforced concrete paver block.
Fig. 20. Fabrication process of chemically modified jute fiber reinforced concrete pavers block
51
(b)
D.4.2. Concrete paver blocks with and without modified jute fiber reinforcement
Three different concrete paver blocks were made with the mix design, which was
developed in this research. Fig. 21a shows the concrete pavers block without any jute fiber
reinforcement. Jute fiber reinforced concrete pavers block is shown in Fig. 21b. Fig. 21c shows
concrete pavers block fabricated by chemically modified jute fiber reinforcement.
Fig. 21a. Paver without jute fiber
reinforcement Fig. 21b. Pavers with untreated
jute fiber reinforcement Fig. 21c. Pavers with chemically modified jute fiber reinforcement
D.4.3. Standard testing of fabricated jute fiber reinforced concrete pavers block There are two standard tests of concrete pavers block. The first one is compressive
strength test of concrete pavers block and the second one is flexural strength test. Both these tests
were performed in the IIT Kharagpur laboratory. Figs.22a and 22b show the testing of concrete
paver blocks.
Fig. 22a. Compressive test of jute reinforced concrete paver block
Fig. 22b. Flexural test of jute reinforced concrete paver block
Tables 13a and 13b show that jute fiber reinforced precast concrete paver tiles achieved
better properties than that of the control paver tiles without jute. The chemically modified jute
52
fiber reinforced concrete paver shows 54 % and 69 % higher compressive and flexural strengths
respectively than that of control concrete pavers block.
Table 13a. Physical properties of concrete paver blocks (cured for 28 days)
Table 13b. Mechanical properties of manufactured concrete paver blocks (cured for 28 days)
D.5. Development of jute fiber reinforced cement flyash roof sheet
Cement-fly ash sheet composites were fabricated by reinforcing with chopped jute fibers
(5 mm length) and jute felts [300x300 (cm2)] of 250, 400 and 600 gsm. At first the chopped jute
fibers and jute felts were soaked into water for 24 h.
For chopped jute fiber reinforced cement-fly ash sheet composites the cement and sand
ratio was 1:1.5, 10 to 50% cement was replaced by fly ash and different weight percent of water
soaked jute fiber were mixed with required amount of water (112.5% w.r.t. cement weight) to
make slurry, following the above process. The fresh mix thus obtained was cast in molds
[(300x300x6) mm3)] under 5 metric ton pressure for 2 h at ambient temperature. After 24 h the
samples were demolded followed by moisture curing for 28 days.
For jute felt reinforced cement-fly ash sheet composites, cement and fly ash (2:3) were
mixed with 112.5% of water w.r.t. cement. The water soaked jute felts were then laminated on
both sides by cement-fly ash mixture and was placed in the molds [300x300x6 (mm3)] under 5
metric ton pressure for 2 h at ambient temperature. After 24 h the samples were demolded and
were moisture cured for 28 days. Fig. 23a and 23b shows the photographs of 28 days water cured
Sample W/C ratio
Type of jute Bulk density Water absorption (%)
Apparent porosity (%)
Control 0.15 - 2.88 8.09 20.9 Raw jute concrete 0.2 Untreated 2.67 8.29 21.11
Chemically treated jute concrete modified with tannin 0.15
Alkali and latex treated 2.88 7.08 20.66
Category Load bearing capacity (Ton)
Compressive strength (MPa)
Flexural strength (MPa)
Control 41.2 2.8 20.2 1.4 3.48 0.2 Raw jute reinforced paver 52.9 6.1 25.9 3.0 5.23 0.3
Chemically treated jute reinforced paver modified with tannin
69.5 2.2 34.1 1.1 5.37 0.2
53
chopped jute fiber reinforced cement-fly ash sheet composites and jute felt reinforced cement-fly
ash sheet composites respectively.
Fig. 23. Photographs of 28 days water cured (a) chopped jute fiber reinforced cement-fly ash sheet composites and (b) jute felt reinforced cement-fly ash sheet composites
54
Achievement 9 The chemically modified jute fiber reinforced NP3 concrete
pipe achieved higher strength than that of conventional NP4 concrete pipe. This means that 31.6% steel requirement can be reduced from NP4 pipe without compromising its properties. Thus, the chemically modified jute fiber reinforced NP3 concrete pipe is cost effective as well as possess better mechanical strength.
9 The paver blocks made by reinforcing with chemically modified jute fiber show 14.6 % less water absorption than the pavers tiles made by raw jute fiber reinforcement.
9 Compressive and flexural strengths of chemically modified jute fiber reinforced pavers tiles achieved 69 and 54 % more strength than the pavers tiles without jute fiber.
9 Jute reinforced concrete pole achieved standard strength (IS 1678) and showed more deflection before failure.
55
SECTION E
Summary and achievement
56
Summary and achievement of project
This work demonstrated the potentiality of jute fiber as reinforcing agent in cement
composites for the use of sewer pipes, prestressed concrete pole, paver blocks. The entire
investigation is summarized below.
Summary
Systematic experimental processes were developed for proper modification of jute fiber with alkali and polymer.
Raw/chemically modified jute fiber reinforced cement composites were fabricated, following a systematic experimental program by considering different experimental
parameters like different processes, fiber content by weight %, fiber length, and curing
time.
Testing of jute fiber reinforced cement concrete composite showed appreciable improvement in mechanical properties, which encourage fabricating prototype cement
concrete products.
The following jute fiber reinforced cement concrete products had been developed so far o Jute fiber reinforced sewer concrete pipes
o Jute fiber reinforced pavement tiles
o Jute fiber reinforced prestressed concrete for electric pole
o Jute fiber reinforced cement fly ash roof sheet
Successful trials of fabrication and testing of 300 mm and 600 mm diameter sewer pipes were completed at M/S Rural Concreting Company of Ghatal Pvt. Ltd.
Industrial trial for fabrication of pavers tiles and testing were performed at M/S Rural Concreting Company of Ghatal Pvt. Ltd.
A field trial on jute fiber reinforced prestressed concrete pole casting and testing had already been done successfully at M/S H. B Housing Industries, West Midnapur.
57
Achievements
9 Chemical modification of jute fiber improved tensile strength and elongation at break about 41 and 34 % respectively.
9 Water absorption of jute fiber was reduced to 108 % from 210 % after chemical and polymer treatment.
9 Technique of short jute fiber (optimum length 4-6 mm) dispersion in concrete/mortar was optimized both in dry and wet basis.
9 Concrete mixing process was optimized with standard ratios of sand, cement, stone chip and water to obtain a concrete having adequate workability during casting.
9 Workability of jute fiber incorporated concrete mix was improved using tannin as admixture.
9 Critical fiber loading was optimized by fabricating cement concrete with different amounts of jute fiber (1-10% w.r.t. weight of cement). Maximum compressive and
flexural strength was achieved at 1% fiber loading in cement composite which was about
4 kg per cubic meter concrete and 5.5 kg per cubic meter cement mortar.
9 Compressive and flexural strengths of chemically treated jute fiber reinforced cement concrete (lab based) were improved by 60 and 66% respectively than that of the concrete
without jute fiber reinforcement.
9 Compressive and flexural strengths of chemically treated jute fiber reinforced cement mortar (lab based) were improved by 11 and 86 % respectively than that of the mortar
without jute fiber reinforcement.
9 Degradation study of jute fiber in cement matrices showed that the rate of degradation of treated jute fibers incorporated in cement paste was very slow whereas in case of
untreated jute fibers incorporated in cement paste degraded rapidly with time. Chemically
modified jute fiber in cement paste retained 97 % of its strength after 90 days aging
duration. Whereas, raw jute fiber in cement paste retained 82% of its strength after 90
days aging.
9 Need assessment, market survey and comparative cost analysis had been done by M/s Roots and Yards, Kolkata.
58
9 The chemically modified jute fiber reinforced NP3 concrete pipe achieved greater strength than that of conventional NP4 concrete pipe. This means that the use of 31.6%
steel can be reduced from NP4 pipe without compromising its properties. Thus, the
chemically modified jute fiber reinforced NP3 concrete pipe is cost effective as well as
mechanically stronger.
9 Pavers blocks made by reinforcing with chemically modified jute fiber showed 14.6 % less water absorption than that of the pavers blocks made by raw jute fiber.
9 Compressive and flexural strengths of chemically modified jute fiber reinforced pavers blocks achieved 69 and 54 % more strength than that of the pavers blocks without jute
fiber.
9 Jute fib