VWR International, Pty Ltd Chemwatch Hazard Alert Code: 3

ISOPROPANOL

Chemwatch: 1219

Version No: 5.1.1.1

Safety Data Sheet according to WHS and ADG requirements

Issue Date: 01/01/2013

Print Date: 17/12/2013

S.GHS.AUS.EN

SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING

Product Identifier

Product name ISOPROPANOL

Chemical Name isopropanol

Synonyms

(CH3)2-CHOH, 1-methylethanol, 2-Propanol (Isopropyl Alcohol) For Synthesis, 2-propanol, Adapt HotStickCleaner/Water Repellent Wipe (Type S), Ashland Isopropyl Alcohol, Avantine Chromar Lutosol, C3-H8-O,CH3-CH(OH)-CH3, DNA Paints & Special Coatings, Product Code: CAO5, David Craig Isopropyl Alcohol, Hewlett-Packard P/N: 92281B P1238.7, IPA, Neogene Isopropyl Alcohol (UN 1219), Tokuyama IPA SE/USE MerckPropan-2-ol AnalaR 10224, TriCom Coatings TT-I-735 Isopropyl Alcohol, Union Carbide Isopropanol AnhydrousSemiconductor Grade, dimethyl carbinol, iso propyl alcohol, isohol petrohol, isopropyl alcohol, sec-propyl alcohol

Proper shipping name ISOPROPANOL (ISOPROPYL ALCOHOL)

Chemical formula C3H8O

Other means of identification Not Available

CAS number 67-63-0

Relevant identified uses of the substance or mixture and uses advised against

Relevant identified usesSolvent for chemicals, paints, varnishes, gums, resins, essential oils. Used in the preservation of physiologicaland pathological specimens., Used for extraction processes, perfumery, and pharmaceuticals. Used in theproduction of acetone, glycerol and isopropyl esters, acetate.

Details of the supplier of the safety data sheet

Registered company name VWR International, Pty Ltd

AddressUnit 1/31 Archimedes Place 4172QLD Australia

Telephone 61 7 3009 4100 ; 1300 727 696

Fax 61 7 3009 4199 ; 1300 135 123

Website http://au.vwr.com

Email csaus@au.vwr.com

Emergency telephone number

Association / Organisation Not Available

Emergency telephone numbers 61 7 3009 4100 ; 1300 727 696

Other emergency telephonenumbers

61 7 3009 4100 ; 1300 727 696

SECTION 2 HAZARDS IDENTIFICATION

Classification of the substance or mixture

HAZARDOUS CHEMICAL. DANGEROUS GOODS. According to the Model WHS Regulations and the ADG Code.

CHEMWATCH HAZARD RATINGS

Continued...

MaxMin

Flammability 3Toxicity 2Body Contact 2Reactivity 2Chronic 2

0 = Minimum1 = Low2 = Moderate3 = High4 = Extreme

Poisons Schedule

GHS Classification[2] Flammable Liquid Category 2, Eye Irrit. 2, STOT - SE (Narcosis) Category 3

Legend:1. Classified by Chemwatch; 2. Classification drawn from HSIS ; 3. Classification drawn from EC Directive1272/2008 - Annex VI

Label elements

GHS label elements

SIGNAL WORD DANGER

Hazard statement(s)

H225 Highly flammable liquid and vapour

H319 Causes serious eye irritation

H336 May cause drowsiness or dizziness

Precautionary statement(s) Prevention

P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.

P271 Use only outdoors or in a well-ventilated area.

P261 Avoid breathing dust/fume/gas/mist/vapours/spray.

P280 Wear protective gloves/protective clothing/eye protection/face protection.

P240 Ground/bond container and receiving equipment.

P241 Use explosion-proof electrical/ventilating/lighting/intrinsically safe equipment.

P242 Use only non-sparking tools.

P243 Take precautionary measures against static discharge.

Precautionary statement(s) Response

P370+P378 In case of fire: Use… to extinguish.

P305+P351+P338IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.

P312 Call a POISON CENTER/doctor/physician/first aider/if you feel unwell.

P337+P313 If eye irritation persists: Get medical advice/attention.

P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.

P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.

Precautionary statement(s) Storage

P403+P235 Store in a well-ventilated place. Keep cool.

P405 Store locked up.

P403+P233 Store in a well-ventilated place. Keep container tightly closed.

Precautionary statement(s) Disposal

P501 Dispose of contents/container to authorised chemical landfill or if organic to high temperature incineration

SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS

Substances

Chemwatch: 1219

Version No: 5.1.1.1

Page 2 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

Continued...

CAS No %[weight] Name

67-63-0 >99 isopropanol

MixturesSee section above for composition of Substances

SECTION 4 FIRST AID MEASURES

Description of first aid measures

Eye Contact

If this product comes in contact with the eyes: Wash out immediately with fresh running water. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids byoccasionally lifting the upper and lower lids. Seek medical attention without delay; if pain persists or recurs seek medical attention. Removal of contact lenses after an eye injury should only be undertaken by skilled personnel. 

Skin ContactIf skin or hair contact occurs:

Flush skin and hair with running water (and soap if available). Seek medical attention in event of irritation. 

Inhalation

If fumes or combustion products are inhaled remove from contaminated area. Lay patient down. Keep warm and rested. Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiatingfirst aid procedures. Apply artificial respiration if not breathing, preferably with a demand valve resuscitator, bag-valve maskdevice, or pocket mask as trained. Perform CPR if necessary. Transport to hospital, or doctor. 

Ingestion

If swallowed do NOT induce vomiting. If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain openairway and prevent aspiration. Observe the patient carefully. Never give liquid to a person showing signs of being sleepy or with reduced awareness; i.e. becomingunconscious. Give water to rinse out mouth, then provide liquid slowly and as much as casualty can comfortably drink. Seek medical advice. If spontaneous vomiting appears imminent or occurs, hold patient's head down, lower than their hips to helpavoid possible aspiration of vomitus. 

Indication of any immediate medical attention and special treatment needed

Any material aspirated during vomiting may produce lung injury. Therefore emesis should not be inducedmechanically or pharmacologically. Mechanical means should be used if it is considered necessary to evacuatethe stomach contents; these include gastric lavage after endotracheal intubation. If spontaneous vomiting hasoccurred after ingestion, the patient should be monitored for difficult breathing, as adverse effects of aspirationinto the lungs may be delayed up to 48 hours.For acute or short term repeated exposures to isopropanol:

Rapid onset respiratory depression and hypotension indicates serious ingestions that require careful cardiacand respiratory monitoring together with immediate intravenous access. Rapid absorption precludes the usefulness of emesis or lavage 2 hours post-ingestion.  Activated charcoal andcathartics are not clinically useful.  Ipecac is most useful when given 30 mins. post-ingestion. There are no antidotes. Management is supportive. Treat hypotension with fluids followed by vasopressors. Watch closely, within the first few hours for respiratory depression; follow arterial blood gases and tidalvolumes. Ice water lavage and serial haemoglobin levels are indicated for those patients with evidence ofgastrointestinal bleeding. 

SECTION 5 FIREFIGHTING MEASURES

Extinguishing media

Alcohol stable foam. Dry chemical powder. BCF (where regulations permit). Carbon dioxide. 

Special hazards arising from the substrate or mixture

Chemwatch: 1219

Version No: 5.1.1.1

Page 3 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

Continued...

Fire IncompatibilityAvoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. asignition may result 

Advice for firefighters

Fire Fighting

Alert Fire Brigade and tell them location and nature of hazard. May be violently or explosively reactive. Wear breathing apparatus plus protective gloves in the event of a fire. Prevent, by any means available, spillage from entering drains or water course. 

Fire/Explosion Hazard

Liquid and vapour are highly flammable. Severe fire hazard when exposed to heat, flame and/or oxidisers. Vapour may travel a considerable distance to source of ignition. Heating may cause expansion or decomposition leading to violent rupture of containers. 

SECTION 6 ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures

Minor Spills

Remove all ignition sources. Clean up all spills immediately. Avoid breathing vapours and contact with skin and eyes. Control personal contact with the substance, by using protective equipment. 

Major Spills

Clear area of personnel and move upwind. Alert Fire Brigade and tell them location and nature of hazard. May be violently or explosively reactive. Wear breathing apparatus plus protective gloves. 

Personal Protective Equipment advice is contained in Section 8 of the MSDS.

SECTION 7 HANDLING AND STORAGE

Precautions for safe handling

Safe handling

Containers, even those that have been emptied, may contain explosive vapours. Do NOT cut, drill, grind, weld or perform similar operations on or near containers. 

DO NOT allow clothing wet with material to stay in contact with skin

Other information

Store in original containers in approved flame-proof area. No smoking, naked lights, heat or ignition sources. 

DO NOT store in pits, depressions, basements or areas where vapours may be trapped.

Conditions for safe storage, including any incompatibilities

Suitable containerDO NOT use aluminium or galvanised containersPacking as supplied by manufacturer. Plastic containers may only be used if approved for flammable liquid. 

Storage incompatibility

Isopropanol (syn: isopropyl alcohol, IPA):forms ketones and unstable peroxides on contact with air or oxygen;  the presence of ketones especiallymethyl ethyl ketone (MEK, 2-butanone) will accelerate the rate of peroxidation reacts violently with strong oxidisers, powdered aluminium (exothermic), crotonaldehyde, diethyl aluminiumbromide (ignition), dioxygenyl tetrafluoroborate (ignition/ ambient temperature), chromium trioxide (ignition),potassium-tert-butoxide (ignition), nitroform (possible explosion), oleum (pressure increased in closedcontainer), cobalt chloride, aluminium triisopropoxide, hydrogen plus palladium dust (ignition), oxygen gas,phosgene, phosgene plus iron salts (possible explosion), sodium dichromate plus sulfuric acid (exothermic/incandescence), triisobutyl aluminium reacts with phosphorus trichloride forming hydrogen chloride gas 

|Avoid isocyanates.

PACKAGE MATERIAL INCOMPATIBILITIES

SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION

Control parameters

OCCUPATIONAL EXPOSURE LIMITS (OEL)

INGREDIENT DATA

Chemwatch: 1219

Version No: 5.1.1.1

Page 4 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

Continued...

Source Ingredient Material name TWA STEL Peak Notes

Australia Exposure Standards isopropanolIsopropylalcohol

983 (mg/m3) / 400(ppm)

1230 (mg/m3) / 500(ppm)

NotAvailable

NotAvailable

EMERGENCY LIMITS

Ingredient TEEL-0 TEEL-1 TEEL-2 TEEL-3

isopropanol 400(ppm) 400(ppm) 2000(ppm) 2000(ppm)

Ingredient Original IDLH Revised IDLH

isopropanol 12,000(ppm) 2,000 [LEL](ppm)

Exposure controls

Appropriate engineeringcontrols

Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard.Well-designed engineering controls can be highly effective in protecting workers and will typically be independentof worker interactions to provide this high level of protection.The basic types of engineering controls are:Process controls which involve changing the way a job activity or process is done to reduce the risk.

Personal protection

Eye and face protection

Safety glasses with side shields. Chemical goggles. Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A writtenpolicy document, describing the wearing of lens or restrictions on use, should be created for each workplace ortask.

Skin protection See Hand protection below

Hand protection

The selection of suitable gloves does not only depend on the material, but also on further marks of quality whichvary from manufacturer to manufacturer. Where the chemical is a preparation of several substances, theresistance of the glove material can not be calculated in advance and has therefore to be checked prior to theapplication.The exact break through time for substances has to be obtained from the manufacturer of the protective glovesandhas to be observed when making a final choice.

Body protection See Other protection below

Other protection

Overalls. PVC Apron. PVC protective suit may be required if exposure severe. Eyewash unit. 

Thermal hazards

Recommended material(s)

GLOVE SELECTION INDEX

Glove selection is based on a modified presentation of the:

 "Forsberg Clothing Performance Index". The effect(s) of the following substance(s) are taken into account in the  ISOPROPANOL

Material CPI

NEOPRENE A

NITRILE A

NITRILE+PVC A

PE/EVAL/PE A

PVC B

* CPI - Chemwatch Performance IndexA: Best SelectionB: Satisfactory; may degrade after 4 hours continuous immersionC: Poor to Dangerous Choice for other than short term immersion

Respiratory protection

Chemwatch: 1219

Version No: 5.1.1.1

Page 5 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

Continued...

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties

Appearance Clear, colourless highly flammable liquid with an odour of rubbing alcohol; mixes with water, alcohol and ether.

Physical state Liquid Relative density (Water = 1) Not Available

Odour Not AvailablePartition coefficient n-octanol /

waterNot Available

Odour threshold Not Available Auto-ignition temperature (°C) 456

pH (as supplied) Not applicable Decomposition temperature Not Available

Melting point / freezing point(°C)

-88.5 Viscosity (cSt) Not Available

Initial boiling point and boilingrange (°C)

82.0 Molecular weight (g/mol) 60.11

Flash point (°C) 11.7 Taste Not Available

Evaporation rate 2.4 BuAc=1 Explosive properties Not Available

Flammability Not Available Oxidising properties Not Available

Upper Explosive Limit (%) 12.7Surface Tension (dyn/cm or

mN/m)Not Available

Lower Explosive Limit (%) 2.3 Volatile Component (%vol) 100

Vapour pressure (kPa) Not Available Gas group IIA

Solubility in water (g/L) Miscible pH as a solution(1%) Not applicable

Vapour density (Air = 1) 2.07

SECTION 10 STABILITY AND REACTIVITY

Reactivity See section 7

Chemical stabilityPresence of incompatible materials. Product is considered stable. Hazardous polymerisation will not occur. 

Possibility of hazardousreactions

See section 7

Conditions to avoid See section 7

Incompatible materials See section 7

Hazardous decompositionproducts

See section 5

SECTION 11 TOXICOLOGICAL INFORMATION

Information on toxicological effects

Inhaled

The material is not thought to produce respiratory irritation (as classified by EC Directives using animal models).Nevertheless inhalation of vapours, fumes or aerosols, especially for prolonged periods, may produce respiratorydiscomfort and occasionally, distress.Inhalation of vapours may cause drowsiness and dizziness. This may be accompanied by narcosis, reducedalertness, loss of reflexes, lack of coordination and vertigo.

Ingestion

Swallowing of the liquid may cause aspiration of vomit into the lungs with the risk of haemorrhaging, pulmonaryoedema, progressing to chemical pneumonitis; serious consequences may result.Signs and symptoms of chemical (aspiration) pneumonitis may include coughing, gasping, choking, burning of themouth, difficult breathing, and bluish coloured skin (cyanosis).Accidental ingestion of the material may be damaging to the health of the individual.Following ingestion, a single exposure to isopropyl alcohol produced lethargy and non-specific effects such asweight loss and irritation.

Skin Contact

The material is not thought to produce adverse health effects or skin irritation following contact (as classified byEC Directives using animal models). Nevertheless, good hygiene practice requires that exposure be kept to aminimum and that suitable gloves be used in an occupational setting.Repeated exposure may cause skin cracking, flaking or drying following normal handling and use.Most liquid alcohols appear to act as primary skin irritants in humans.

Chemwatch: 1219

Version No: 5.1.1.1

Page 6 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

Continued...

Eye

Evidence exists, or practical experience predicts, that the material may cause eye irritation in a substantialnumber of individuals and/or may produce significant ocular lesions which are present twenty-four hours or moreafter instillation into the eye(s) of experimental animals.Repeated or prolonged eye contact may cause inflammation characterised by temporary redness (similar towindburn) of the conjunctiva (conjunctivitis); temporary impairment of vision and/or other transient eyedamage/ulceration may occur.Isopropanol vapour may cause mild eye irritation at 400 ppm. Splashes may cause severe eye irritation, possiblecorneal burns and eye damage.

Chronic

Limited evidence suggests that repeated or long-term occupational exposure may produce cumulative healtheffects involving organs or biochemical systems.Long term or repeated ingestion exposure of isopropanol may produce incoordination, lethargy and reduced weightgain.

Repeated inhalation exposure to isopropanol may produce narcosis, incoordination and liver degeneration. Animaldata show developmental effects only at exposure levels that produce toxic effects in the adult animals.

isopropanol

TOXICITY IRRITATION

Dermal (rabbit) LD50: 12800mg/kg

Eye (rabbit): 10 mg - moderate

Inhalation (Mouse) LC50: 53000mg/m3/4h

Eye (rabbit): 100 mg - SEVERE

Inhalation (Rat) LC50: 72600mg/m3/4h

Eye (rabbit): 100mg/24hr-moderate

Intraperitoneal (Guinea pig) LD50:2560 mg/kg

Skin (rabbit): 500 mg - mild

Intraperitoneal (Mouse) LD50:4477 mg/kg

Intraperitoneal (Rabbit) LD50: 667mg/kg

Intraperitoneal (Rat) LD50: 2735mg/kg

Intravenous (Mouse) LD50: 1509mg/kg

Intravenous (Rabbit) LD50: 1184mg/kg

Intravenous (Rat) LD50: 1088mg/kg

Oral (Mouse) LD50: 3600 mg/kg

Oral (Rabbit) LD50: 6410 mg/kg

Oral (Rat) LD50: 5000 mg/kg

Oral (rat) LD50: 5045 mg/kg

Not Available Not Available

* Value obtained from manufacturer's msdsunless otherwise specified data extracted from RTECS - Register of Toxic Effects of Chemical Substances

ISOPROPANOLFor isopropanol (IPA):

Acute toxicity: Isopropanol has a low order of acute toxicity. It is irritating to the eyes, but not to the skin.

Acute Toxicity Not Applicable Carcinogenicity Not Applicable

Skin Irritation/Corrosion Not Applicable Reproductivity Not Applicable

Serious Eye Damage/Irritation Eye Irrit. 2 STOT - Single Exposure STOT - SE (Narcosis) Category 3

Respiratory or Skinsensitisation

Not Applicable STOT - Repeated Exposure Not Applicable

Mutagenicity Not Applicable Aspiration Hazard Not Applicable

CMR STATUS

Chemwatch: 1219

Version No: 5.1.1.1

Page 7 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

Continued...

SECTION 12 ECOLOGICAL INFORMATION

Toxicity

For isopropanol (IPA):log Kow  : -0.16- 0.28Half-life (hr) air  : 33-84Half-life (hr) H2O surface water  : 130

Persistence and degradability

Ingredient Persistence: Water/Soil Persistence: Air

Not Available Not Available Not Available

Bioaccumulative potential

Ingredient Bioaccumulation

Not Available Not Available

Mobility in soil

Ingredient Mobility

Not Available Not Available

SECTION 13 DISPOSAL CONSIDERATIONS

Waste treatment methods

Product / Packaging disposalLegislation addressing waste disposal requirements may differ by country,  state and/ or territory. Each user mustrefer to laws operating in their area. In some areas, certain wastes must be tracked.A Hierarchy of Controls seems to be common - the user should investigate:

SECTION 14 TRANSPORT INFORMATION

Labels Required

Marine Pollutant: NO

HAZCHEM •2YE

Land transport (ADG)

UN number 1219*

Packing group II

UN proper shipping name ISOPROPANOL (ISOPROPYL ALCOHOL)

Environmental hazard No relevant data

Transport hazard class(es)Class 3

Subrisk

Special precautions for userSpecial provisions

limited quantity 1 L

Air transport (ICAO-IATA / DGR)

UN number 1219*

Packing group II

UN proper shipping name Isopropanol; Isopropyl alcohol

Environmental hazard No relevant data

Chemwatch: 1219

Version No: 5.1.1.1

Page 8 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

Continued...

Transport hazard class(es)

ICAO/IATA Class 3

ICAO / IATA Subrisk

ERG Code 3L

Special precautions for user

Special provisions A180

Cargo Only Packing Instructions 364

Cargo Only Maximum Qty / Pack 60 L

Passenger and Cargo Packing Instructions 353

Passenger and Cargo Maximum Qty / Pack 5 L

Passenger and Cargo Limited Quantity Packing Instructions Y341

Passenger and Cargo Maximum Qty / Pack 1 L

Sea transport (IMDG-Code / GGVSee)

UN number 1219*

Packing group II

UN proper shipping name ISOPROPANOL (ISOPROPYL ALCOHOL)

Environmental hazard No relevant data

Transport hazard class(es)IMDG Class 3

IMDG Subrisk

Special precautions for user

EMS Number F-E,S-D

Special provisions

Limited Quantities 1 L

Transport in bulk according to Annex II of MARPOL 73 / 78 and the IBC code

Source IngredientPollutionCategory

Residual Concentration - Outside Special Area(% w/w)

ResidualConcentration

IMO MARPOL 73/78 (Annex II) -List of Other Liquid Substances

isopropanol Not Available Not Available Not Available

SECTION 15 REGULATORY INFORMATION

Safety, health and environmental regulations / legislation specific for the substance or mixture

isopropanol(67-63-0) is found onthe following regulatory lists

"Australia Hazardous Substances Information System - Consolidated Lists","OECD List of High Production Volume(HPV) Chemicals","Australia High Volume Industrial Chemical List (HVICL)","IOFI Global Reference List ofChemically Defined Substances","International Fragrance Association (IFRA) Survey: TransparencyList","Australia Inventory of Chemical Substances (AICS)","FisherTransport Information","Sigma-AldrichTransportInformation","Acros Transport Information","IMO IBC Code Chapter 18: List of products to which the Code doesnot apply","IMO MARPOL 73/78 (Annex II) - List of Other Liquid Substances","IMO Provisional Categorization ofLiquid Substances - List 2: Pollutant only mixtures containing at least 99% by weight of components alreadyassessed by IMO","GESAMP/EHS Composite List - GESAMP Hazard Profiles","International Agency for Researchon Cancer (IARC) - Agents Reviewed by the IARC Monographs","Australia Exposure Standards","InternationalMaritime Dangerous Goods Requirements (IMDG Code) - Substance Index","International Maritime DangerousGoods Requirements (IMDG Code)","Australia Dangerous Goods Code (ADG Code) - List of Emergency ActionCodes","Belgium Federal Public Service Mobility and Transport, Regulations concerning the International Carriageof Dangerous Goods by Rail - Table A: Dangerous Goods List - RID 2013 (Dutch)","International Air TransportAssociation (IATA) Dangerous Goods Regulations","Australia Dangerous Goods Code (ADG Code) - DangerousGoods List","Australia Quarantine and Inspection Service List of chemical compounds that are accepted solely foruse at establishments registered to prepare meat and meat products for the purpose of the Export Control Act1982","Australia National Pollutant Inventory","IMO IBC Code Chapter 17: Summary of minimumrequirements","OSPAR National List of Candidates for Substitution – Norway"

SECTION 16 OTHER INFORMATION

Other informationClassification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by theChemwatch Classification committee using available literature references.

Chemwatch: 1219

Version No: 5.1.1.1

Page 9 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

Continued...

A list of reference resources used to assist the committee may be found at: www.chemwatch.net/references

The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazardsare Risks in the workplace or other settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and currentor available engineering controls must be considered.

This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or criticism, as permitted under the CopyrightAct, no part may be reproduced by any process without written permission from CHEMWATCH. TEL (+61 3) 9572 4700.

Chemwatch: 1219

Version No: 5.1.1.1

Page 10 of 10 Issue Date: 01/01/2013

Print Date: 17/12/2013isopropanol

end of SDS