2020 www.ircrating.org

IRC is a World Sailing recognised International Rating System

1

EFFECTIVE 1 JANUARY 2020

IN COUNTRIES WITH JUNE-MAY VALIDITY, EFFECTIVE 1 JUNE 2020

Copyright Seahorse Rating Ltd.

All rights reserved. No part of this Rule may be reproduced, transmitted or recorded by any means without the prior permission of Seahorse Rating Ltd.

PREAMBLE Any changes herein have no authority until 1 January 2020 (1 June 2020 in countries where certificate validity is 1 June to 31 May).

IRC is a rating rule providing racing for 2 separate classes of boats. Part C permits advertising in accordance with World Sailing Regulation 20, Advertising Code. Part D does not permit advertising. Organising Authorities should specify in a Notice of Race either Part C or Part D. If neither is specified, then by default Part C shall apply.

TERMINOLOGY A term used in its defined sense is printed in “bold” type if defined in the ERS, in “italic” type if defined in the RRS and in “underscore” type if defined in IRC Rules. Any abbreviation given in Appendix 1 is used in its defined term unless specified otherwise.

Equipment Rules of Sailing (ERS) – www.sailing.org/ers Racing Rules of Sailing (RRS) – www.sailing.org/rrs Offshore Special Regulations (OSR) – www.sailing.org/specialregs Or download the free rules app for iOS, Android and Windows by searching for World Sailing.

2

CONTENTS PREAMBLE .............................................................................................................................. 1 TERMINOLOGY ........................................................................................................................ 1 CONTENTS .............................................................................................................................. 2 PART A- RULE POLICY .............................................................................................................. 3

1 INTRODUCTION ..................................................................................................................... 3 2 FUNDAMENTAL POLICY ......................................................................................................... 3 3 IMPORTANT NOTICE .............................................................................................................. 3

PART B- GENERAL INFORMATION ............................................................................................ 4 4 ADMINISTRATION .................................................................................................................. 4 5 INTERPRETATIONS ................................................................................................................. 5 6 DISPENSATIONS ..................................................................................................................... 5 7 LANGUAGE AND RULE DEFINITIONS ..................................................................................... 5 8 RATING CERTIFICATES ........................................................................................................... 5 9 RATING REVIEW ..................................................................................................................... 7 10 RATING PROTESTS ................................................................................................................. 8 11 CHANGES TO CLASS RULES .................................................................................................... 9 12 UNITS OF MEASUREMENT AND CORRECTED TIMES ............................................................. 9 13 MEASUREMENT AND COMPLIANCE ...................................................................................... 9 14 SAIL NUMBERS ..................................................................................................................... 10 15 MANUAL POWER ................................................................................................................. 10

PART C- IRC, ADVERTISING PERMITTED .................................................................................. 10 16 ADVERTISING ....................................................................................................................... 10 17 BOAT WEIGHT...................................................................................................................... 10 18 OVERHANGS AND DRAFT .................................................................................................... 11 19 HULL APPENDAGES .............................................................................................................. 11 20 ENGINE AND PROPELLER ..................................................................................................... 12 21 RIG AND SAILS ..................................................................................................................... 12 22 EQUIPMENT AND LOADING ................................................................................................ 15 23 SEAWORTHINESS AND SAFETY ............................................................................................ 16

PART D - IRC, ADVERTISING NOT PERMITTED ......................................................................... 16 25 RULES ................................................................................................................................... 16 26 ADVERTISING ....................................................................................................................... 16

APPENDIX - IRC MEASUREMENT DEFINITIONS AND ABBREVIATIONS ...................................... 17 MISCELLANEOUS ......................................................................................................................... 17 HULL & APPENDAGES .................................................................................................................. 17 RIG 18 SAILS – GENERAL ......................................................................................................................... 19 SAILS - HEADSAILS ....................................................................................................................... 20 SAILS - MAINSAIL ......................................................................................................................... 21 SAILS - SPINNAKER ....................................................................................................................... 21

APPENDIX - IRC MEASUREMENT DIAGRAMS .......................................................................... 22

3

PART A- RULE POLICY

1 INTRODUCTION

1.1 The Rule is in two parts, Part C, IRC, advertising permitted, and Part D, IRC, advertising not permitted. IRC is a rating rule based upon owner-supplied information and will remain unpublished. The emphasis is on simplicity and concise rules.

2 FUNDAMENTAL POLICY 2.1 IRC is a system of measurement which classifies a broad range of cruising and racing

ballasted monohull keel boats for competition by providing ratings comprising single figure allowances based on time. Except for designs first rated before 1st January 2016, boats shall have a minimum hull length of 5.00 m.

2.2 The IRC concept protects the existing IRC fleet. 2.3 IRC encourages design innovation consistent with stability, rounded performance,

seaworthiness and safety. 2.4 IRC discourages unnecessary expense at all levels. 2.5 The spirit of IRC requires that owners and designers shall not seek means of artificially

reducing the rating of a boat, e.g. increasing performance without a corresponding increase in rating.

2.6 Calculation of IRC ratings is unpublished and based on measurement and data input only.

2.7 IRC ratings may rely on owner submitted data (see Rules 8.5 and 9) but a Rule Authority (as defined in Rule 4.1) may require that boats be weighed and measured by an appointed measurer for certificates issued under their jurisdiction. Some or all of the dimensions of class production boats may be standardised.

2.8 Any exploitation of the inherent simplicity of the IRC Rule will be discouraged. The RORC Rating Office and UNCL therefore reserve the right to make adjustments or amendments to any part of IRC at any time in order to prevent undesirable or unforeseen lines of development.

3 IMPORTANT NOTICE

3.1 The safety of a boat rated under IRC and its entire management including insurance shall be the sole responsibility of the owner/competitor who must ensure that the boat is fully found, thoroughly seaworthy, and operated by a crew sufficient in number and experience who are physically fit to face bad weather. The owner/competitor must be satisfied that:

3.1.1 The hull, hull appendages, spars, rigging, sails and all gear are sound. 3.1.2 All safety equipment is properly maintained, stowed and in date. 3.1.3 The crew know where such equipment is kept and how it is to be used. The ultimate decision on whether or not to race remains the sole and inescapable

responsibility of the owner or the owner’s representative.

4

3.2 None of the establishment of these Rules, their use by race organisers, the issue of a rating certificate under these Rules, nor any inspection of the boat under these Rules shall constitute any representation or warranty by the Rating Authority as to the seaworthiness of any boat or the safety of any gear and shall not in any way limit the absolute responsibility of the owner/competitor referred to in Rule 3.1. This notice shall be brought to the attention of any person who sails on a boat in respect of which a rating certificate has been issued under these Rules.

3.3 Ratings issued under IRC are calculated in good faith from the data available. Neither the Rating Authority nor any Rule Authority shall have any liability whatsoever for any error in the application of these Rules or the determination of any factor which may affect the rating or the exercise of any judgement in the application of these Rules or the issue of a certificate or for changes in these Rules.

3.4 The establishment of an IRC Crew Number in respect of any boat does not constitute any representation or warranty as to the safety of the boat when sailing with this or any other number of crew (see Rule 3.1). When domestic law invokes any form of crew limitation different from the IRC Crew Number, this limitation shall replace IRC Crew Number.

PART B- GENERAL INFORMATION

4 ADMINISTRATION

4.1 IRC is administered by Seahorse Rating Ltd (referred to in these Rules as the RORC Rating Office) and the UNCL Centre de Calcul (referred to as UNCL) only. The expression Rating Authority is defined as the RORC Rating Office and the UNCL Centre de Calcul acting jointly. The expression Rule Authority is defined as any other individual or body authorised by the Rating Authority to act for the Rating Authority on a local basis for the administration of IRC in a defined geographical area.

4.2 In order to ensure the integrity of the unpublished elements of the IRC Rule all details of the IRC Rule are the sole property of the RORC Rating Office and UNCL who shall appoint an IRC Technical Committee comprised solely of those persons who have knowledge of the unpublished elements of the Rule. This committee shall be solely responsible for any changes in the Rule algorithms.

4.3 IRC TCCs are the copyright of RORC Rating Office and UNCL jointly and shall not be modified by any third party. Action may be taken against any third party using IRC-derived handicaps, whether precise or amended for the purpose of race handicapping any boat without a current IRC certificate. Adjustment of elapsed time to effectively amend an IRC TCC is considered to be modification of the IRC TCC by a third party unless:

(a) agreed in writing by the Rating Authority for a specific purpose, or (b) applied due to an infringement of a rule while racing as defined in the sailing

instructions which would otherwise be a matter for a protest committee, or (c) application of a penalty by a protest committee. Stability and Safety Screening numerals are RORC Rating Office copyright.

5

4.4 The IRC Policy Steering Group is responsible for the overall direction of IRC. The IRC Policy Steering Group comprises representatives appointed by RORC and UNCL and a representative appointed by the International IRC Owners Association.

4.5 Additionally there shall exist an International IRC Owners' Association comprising owners of boats holding current IRC certificates. The International IRC Owners' Association shall have international representation which reflects the distribution of certificated boats, and shall be a forum for owners to discuss and, if agreed, to make recommendations or suggestions to the IRC Technical Committee and the IRC Policy Steering Group.

5 INTERPRETATIONS

5.1 Requests for interpretation of the IRC Rule shall be made in writing through Rule Authorities to the Rating Authority who will consult and communicate any decision to Rule Authorities.

6 DISPENSATIONS

6.1 The Rating Authority may grant dispensations to the IRC Rule on an individual boat basis at its entire discretion. Any such dispensations shall be noted on a boat's IRC certificate.

7 LANGUAGE AND RULE DEFINITIONS

7.1 The languages of IRC shall be English and French. In the event of any discrepancy, the English text shall prevail. The meaning of any word shall be by reference to the Oxford English Dictionary in the context in which it appears. The words ‘shall’ and ‘must’ are mandatory, the words ‘may’ and ‘can’ are permissive. The word ‘should’ is advisory.

7.2 Any reference to the Racing Rules of Sailing (RRS) is defined as the current version of the World Sailing Racing Rules of Sailing. Reference to the Equipment Rules of Sailing (ERS) refers to the current version of the World Sailing Equipment Rules of Sailing. Reference to Special Regulations (OSR) is defined as the current version of World Sailing Offshore Special Regulations.

7.3 ERS shall apply except where deleted or amended by IRC Rules or Appendix 1. 7.4 Any dispute arising out of the administration of the IRC Rules by the Rating Authority or

a Rule Authority shall be referred to the IRC Policy Steering Group referred to in Rule 4.4 - which shall allow the applicant to be given a fair opportunity to make his case either in writing or in person (as the IRC Policy Steering Group may determine). The decision of the IRC Policy Steering Group shall be final.

8 RATING CERTIFICATES 8.1 All IRC ratings will be calculated by and rating certificates issued by the Rating Authority.

Rule Authorities may be authorised to print rating certificates under licence. 8.2 A boat shall hold a current IRC certificate valid in the country in which it is racing. A boat

shall not hold more than one valid IRC rating certificate at any time except as permitted by Rules 8.2.1 and 8.2.2.

6

8.2.1 A boat may additionally hold a separate short-handed certificate. This short-handed certificate shall be valid only for racing in classes, or divisions of classes, for no more than 2 crew, included in a Notice of Race. When specified in a Notice of Race, boats holding short handed certificates, and racing in a short handed class or division, may also be scored in the overall results of the race. The short-handed certificate will be clearly identified and shall only vary from the primary certificate in respect of, mainsail widths, headsail dimensions, single furling headsail allowance, the use of stored power, SPA, STL, spinnaker pole/bowsprit, number of spinnakers, moveable ballast and variable ballast. A boat holding a shorthanded certificate shall use that certificate for races for no more than 2 crew.

8.2.2 Issue of any new rating certificate automatically invalidates the old one except when a new certificate is issued to enable a boat to race in another country with a different certificate year end.

8.2.3 A copy of the current rating certificate(s) shall be kept on board the boat. 8.3 An IRC certificate is valid for racing under Part C, IRC, advertising permitted and Part D,

IRC, advertising not permitted. 8.4 Rating certificates will be issued with the heading of the Rule Authority and any

sponsorship as appropriate. 8.5 An ENDORSED IRC certificate is one for which the data on the certificate has been

audited and if necessary verified by measurement, or other methods in accordance with current published standards. An owner may apply to their Rule Authority to have an IRC rating certificate Endorsed. The Rule Authority will inform the owner of any measurement, including weighing, or other checks required prior to issue by the Rating Authority of a certificate carrying (irrespective of certificate print language) the notation ENDORSED under the IRC Rating Authority stamp (see also Rule 13).

8.6 On IRC certificates for all boats rated to carry spinnakers (see Rule 21.6), a non spinnaker TCC is also printed. The non spinnaker TCC shall be valid only for races for which the Notice of Race includes a non spinnaker division or class. Owners shall declare their intention to enter such a non spinnaker class using the non spinnaker TCC a minimum of seven days before the race, or first race if a series of races, and shall not then be permitted to race using a spinnaker for the race or races. This Rule may be amended by a Notice of Race.

8.7 The Rating Authority may at its sole discretion re-issue or may refuse to issue or to re-issue an IRC certificate if in its sole opinion Rule 2.5 may be infringed, or for any other reason. No reason need be stated.

8.8 Change of ownership and/or any changes in sail number will automatically invalidate the rating certificate.

8.9 Physical changes which might affect the performance of the boat shall be declared and may invalidate the rating certificate.

8.10 Rated Dimensions 8.10.1 Values stated on certificates for LH, Hull Beam, Bulb Weight, Draft, x, P, E, J, FL,

MUW, MTW, MHW, HLUmax, HSA, PY, EY, LLY, LPY, Cutter Rig HLUmax, SPA, STL are maximum values.

7

8.10.2 Values stated on certificates for Boat Weight, BO, h, SO, y, and Internal Ballast are minimum values.

8.10.3 If during Equipment Inspection by an Equipment Inspector, or during measurement carried out under Rules 10.2 or 13.6, any rated dimension is found to exceed a maximum value or to be less than a minimum value, then the boat is not in compliance with her certificate.

8.10.4 Attention is drawn to Rule 13 and to RRS 78, Compliance with Class Rules; Certificates.

8.11 When the Rating Authority has reasonable evidence that a boat does not conform to its certificate, or that there has been a breach of these Rules, or that there has been an error in the determination of the rating, or that there has been a gross breach of the IRC Rules or of good manners or sportsmanship, the certificate may (at the absolute discretion of the Rating Authority) be withdrawn without compensation and the owner shall be informed in writing.

8.12 Certificates will normally be valid on payment of the appropriate fee for the current calendar year only, but at the discretion of the relevant Rule Authority, and with agreement from the Rating Authority, the year may run from 1 June to 31 May of the following year.

8.13 Irrespective of where a boat is registered, she shall apply for her IRC certificates to the appointed Rule Authority in the country in which she predominantly races. Exceptionally, with the agreement of the Rating Authority, she may apply through another Rule Authority.

8.14 On request and payment of a fee, and in accordance with any administrative rules published by the Rating Authority, the Rating Authority may supply a copy of a boat’s valid or immediately expired IRC certificate, including owner name, to any interested party.

9 RATING REVIEW

Rule 9 does not apply to equipment inspection at an event. 9.1 Review of a boat’s rating may be requested at any time by the owner who should submit

a review request through their Rule Authority to the Rating Authority. A fee may apply. 9.2 Anyone who has a valid interest in a boat's certificate may also request a rating review

from the Rating Authority, by submitting a review request through their Rule Authority to the Rating Authority. A fee may apply. The owner of the boat subject to review will be requested to file a reply as soon as possible.

9.3 The Rating Authority may also review a rating at any time. 9.4 A review shall be based on all the available evidence. Where necessary, rated data shall

be re-measured by an authorised measurer. The decision of the Rating Authority on any review shall be final.

9.5 For series produced boats, the rated data may have been standardised by the Rating Authority. Standard data shall not be subject to third party review or protest. A rating review may be requested by the manufacturer or the class association of a series produced boat. Modifications to standard data shall be declared by the owner.

8

9.6 Where the TCC is reviewed and found to be not more than 0.005 greater than before, the contested rating shall be valid up to the date that the request for review was lodged with the Rating Authority, or in the case of a protest up to but excluding the race in which the protest was lodged, except that if Rule 8.9 applies then from the date of the change. This Rule may be amended by Notice of Race only to the extent that the 0.005 limit may be reduced.

9.7 Where the TCC is reviewed, either as a result of a rating review or a protest, and found to be more than 0.005 greater than before, the contested certificate is invalid from the date of issue.

9.8 In either case where the TCC is reviewed, the certificate becomes invalid if any re-measurement which increases the boat’s rating differs from the measurement shown on the certificate by more than 1% of: LH, LWP, Hull Beam, Draft, P, E, J, FL, STL, HLUmax, MUW, MTW, MHW (see Appendix 1); by more than 2% of SPA or HSA; by more than 5% of y, x or h; or by 5% in respect of weights; or if specific detail is clearly in error.

9.9 Following review and re-measurement, a new certificate may be issued which may be back-dated to the date that any erroneous data was supplied.

9.10 The owner of a boat requesting review of his own boat's rating is liable for all measurement and rating costs. In all other cases, unless as a result of review a boat's certificate is invalidated under Rules 9.7 or 9.8, the person requesting the review shall pay measurement and rating costs unless the Rating Authority orders otherwise.

10 RATING PROTESTS

10.1 As permitted by the RRS, a rating protest may be submitted to a protest committee. A protest committee may refer the matter to the Rating Authority with the appropriate fee.

10.2 In the event of protest, the boat's rated data may be re-measured by an authorised measurer.

10.3 A boat whose certificate is invalidated as a result of an error or omission by a Rule Authority or by the Rating Authority, of which the boat could not reasonably have been aware, may be penalised at the discretion of the protest committee. Additionally, a protest committee may order that races scored using the invalidated certificate shall be re-scored using the corrected TCC.

10.4 A boat whose certificate is invalidated in accordance with Rule 9.6 may be penalised at the discretion of a protest committee. Additionally, a protest committee may order that races under its jurisdiction scored using the invalidated certificate shall be re-scored using the corrected TCC.

10.5 Subject to the RRS, when a boat is penalised by a protest committee as a result of her certificate being invalidated under Rules 9.7 or 9.8, her owner shall be liable for measurement and rating costs unless the protest committee orders otherwise. In all other cases, the protestor shall be liable for measurement and rating costs.

10.6 When as a result of an action in a race or series, or the withdrawal of a certificate by the Rating Authority, a boat's rating is reviewed and its TCC changes, the boat's Member National Authority may be requested by the Rating Authority to investigate the circumstances and report its findings to the Rating Authority.

9

11 CHANGES TO CLASS RULES

11.1 A Rule Authority Prescription or Notice of Race may vary the requirements of IRC Rules 8.6, 9.6, 14.1, 15.1, 21.1.5 (d) (e) and (f), 21.8.4, and 22.4. Any Rule Authority prescriptions shall have been approved by the national IRC Owners’ Association when such exists. No other IRC Rules may be amended.

11.2 A Rule Authority may prescribe that for races under its jurisdiction requiring compliance with OSR Category 3 or above, Rule 21.6.1 is varied to the extent that a boat may carry one more spinnaker than shown on her current IRC certificate of area not greater than rated SPA without an increase in rating.

11.3 Where a Rule Authority has made a Prescription to a Rule, a Notice of Race shall not vary that Rule or Prescription without the permission of the Rule Authority. Rule Authority Prescriptions shall be referenced in a Notice of Race.

12 UNITS OF MEASUREMENT AND CORRECTED TIMES 12.1 Measurements shall be taken in units of the metric system. Sail measurements shall be

taken in metres to two decimal places. All other linear measurements shall be taken in metres to three decimal places and rounded to two decimal places for input. Weight shall be taken to the nearest kilogram except in the case of boat weight which shall be to the nearest 10 kilograms. Normal mathematical conventions shall apply, with 0.5 rounding up. Full calculated values will be carried forward to subsequent calculations. Final ratings shall be rounded to three decimals places.

12.2 The IRC rating is calculated as a Time Corrector (TCC) to three places of decimals. Corrected time for each boat is calculated by multiplying its elapsed time by its TCC. Corrected times shall be rounded to the nearest second with 0.5 seconds rounding up.

13 MEASUREMENT AND COMPLIANCE

13.1 Measurement data shall be obtained by direct measurement or derived from another rating certificate whenever possible. If another rating certificate is being used as the basis for data then any changes since the issue of that certificate shall be notified to the Rating Authority.

13.2 Measurements shall be taken in accordance with ERS Part 3 – Rules Governing Equipment Control and Inspection. ERS H.5.4 is amended by the addition of:

The batten specified in ERS H.5.4. shall be a standard 1m World Sailing blue batten. If an alternative length batten is required to achieve a consistent and repeatable measurement, the measurer shall use a batten of consistent bend characteristics and of a length not longer than the greater of 1m or 25% of foot length. If a batten longer than 1m is used, the measurer shall report the batten length and the reason for using the alternative batten to the Rating Authority.

13.3 The accuracy of measurements supplied shall be the owner's responsibility. An IRC measurement service is available on application to a boat's Rule Authority.

13.4 It is a breach of the Rules of IRC for any owner or individual to intentionally supply false information. Attention is drawn to Rule 8.7 and to RRS 69, Allegations of Gross Misconduct.

10

13.5 The Rating Authority will use the data supplied by a Rule Authority as a basis for rating but reserves the right to overrule specific data or to standardise the dimensions of a class of production boats.

13.6 The Rating Authority or a boat's Rule Authority may require a boat to be submitted for measurement at any time without giving reasons. Measurement will be undertaken by authorised measurers of the Rating Authority. A new certificate will be issued by the Rating Authority based on the new measurement data.

13.7 In the particular case of a boat issued with a one-design certificate, as noted on the certificate, the rating requires compliance with one-design class rules. In the event of conflict, IRC Rules shall take precedence. See also Rule 22.4.1.

14 SAIL NUMBERS

14.1 Each boat shall hold a sail number as prescribed by its Member National Authority. Sail numbers shall be displayed in accordance with RRS 77, Identification on Sails. This Rule may be amended by Notice of Race.

15 MANUAL POWER

15.1 RRS 52, Manual Power, shall not apply. This Rule may be amended by Notice of Race. 15.2 (a) The use of stored power for the hoisting of mainsails, or the reefing or furling of sails

need not be declared. (b) Boats using stored power solely for the adjustment or operation of backstays shall

declare this to the Rating Authority. (c) Boats using stored power for the adjustment or operation of running rigging other

than as noted in Rules 15.2(a) & (b) shall declare this to the Rating Authority.

PART C- IRC, ADVERTISING PERMITTED

16 ADVERTISING 16.1 Advertising may be displayed in accordance with World Sailing Regulation 20,

Advertising Code.

17 BOAT WEIGHT

17.1 Boat Weight is measured in accordance with the following Conditions for Weight and Flotation Measurement:

The boat shall: be dry. be in compliance with the class rules (ie. IRC Rules) Unless otherwise specified in the rules, any of the following shall be included: rig including spinnaker pole(s), whisker poles and/or jockey pole main sheet and mizzen sheet, vang, inboard engine or outboard engine in stowed position, fitted berth cushions on board in their normal positions if carried while racing all permanent fixtures and fittings and items of accommodation.

11

Unless otherwise specified in the rules, any of the following shall be excluded: sails fuel, water, variable ballast or the content of any other tanks, gas bottles portable safety equipment and all other unfitted or loose equipment.

17.2 Spare. 17.3 When for practical reasons it is not possible to remove all items and equipment (e.g.

fuel), it is acceptable to deduct the weight of these from the gross weight. The Rating Authority reserves the right to refuse such data when inadequate detail is supplied.

17.4 The Rating Authority will calculate the boat weight of an un-weighed boat based on information contained on another rating certificate, designer data or from any other source.

17.5 In the absence of other information, boat weight may be calculated by deduction of the items detailed by Rule 17.1 from a boat's sailing displacement or sailing weight.

18 OVERHANGS AND DRAFT

18.1 Measurements shall be taken with the boat in flotation trim. The measurement points for various configurations of boats are shown on the diagrams for hull shapes and are defined in Appendix 1.

19 HULL APPENDAGES 19.1 Full details of a boat's hull appendages shall be supplied to the Rating Authority at the

time of rating application. 19.2 Any keel fin fairings with a nominal density, including any cavities and/or core material,

significantly lower than the main structural elements of the keel fin shall be declared. For the purpose of this rule, a keel fin fairing does not include surface fairing, filling and painting materials up to a total thickness of 10 mm, measured normal to the local surface of the keel fin.

19.3 Drop keels, centreboards, bilgeboards and other moveable hull appendages shall be declared. Unless fixed down while racing, drop keels will be rated as moveable hull appendages.

19.4 In the construction of hull appendages, no material with specific gravity greater than 11.3 is permitted.

19.5 Boats including material in their hull appendages with specific gravity greater than 11.3, and with age date of 2005 or earlier, and holding a valid IRC certificate on 31st December 2005 are exempt from Rule 19.4. Apart from routine maintenance, any such boat changing the quantity of material of specific gravity greater than 11.3 shall comply with Rule 19.4 and will not subsequently be eligible for exemption from compliance with Rule 19.4.

19.6 Any material in the keel fin of a keel type 10, 11 or 12 with a specific gravity greater than 8.0 (eg. lead) shall be declared in writing.

12

20 ENGINE AND PROPELLER

20.1 Boats will be rated with either: 20.1.1 No engine. 20.1.2 Outboard engine (i.e. an engine where the propeller may be removed from the

water while racing). 20.1.3 Inboard engine, including strut drive and stern-drive configurations. Propeller

type shall be declared at the time of rating application. 20.2 Inboard engines shall be capable of producing a minimum speed of 1.8*LWP^0.5 knots.

Outboard engines shall be securely fastened in their normal stowage positions for racing.

21 RIG AND SAILS

21.1 General 21.1.1 Single and twin masted rigs only may be rated under IRC. 21.1.2 'Cat' rig is defined as a rig where no sails are set forward of the mast(s) when

sailing to windward. 21.1.3 'Gaff' rig includes square, spritsail and other similar rig configurations. 21.1.4 Mizzen staysails shall be declared.

21.1.5 There is no limitation on the number or type of sails on board while racing under IRC except: (a) the limitation on spinnaker numbers (see Rule 21.6.1). (b) the limitation on sails containing exotic materials (see Rule 21.2.2). (c) the limitation on headsail numbers for boats rated with a single furling

headsail. Except in the cases of significant damage or storm and heavy weather sails, boats claiming a rating allowance for using a single roller furling headsail shall use the same headsail for all races in any series of races. (see Rule 21.8.1)

(d) during a regatta run on consecutive days, including any lay days, the sails on board shall remain the same and be on board for all races. This Rule may be amended by Notice of Race.

(e) a spare mainsail may be on board but may not be used as a racing replacement, either during a race or during a regatta run on consecutive days, including any lay days. This Rule may be amended by Notice of Race.

(f) exceptionally, in the case of significant damage or loss, sails may be replaced with similar sails. A Notice of Race may require that boats obtain permission from the Race Committee before replacing a sail. This Rule may be amended by Notice of Race.

(g) sails shall be set in close proximity to the boat. (h) sails with detachable sections of sail cloth are not permitted.

21.1.6 (a) Adjustment or detachment of forestay and/or shrouds including diagonal and jumper shrouds, or movement of the mast at the foot or the deck while racing is not permitted except:

13

(i) in the case of a boat without running backstays, checkstays or adjustable backstay when the forestay may be adjusted but not detached.

(ii) in the case of boats with LH less than 10m and without lifelines that are explicitly permitted by their own class rules to move the mast at foot or deck level, or to adjust or detach the forestay and shrouds while racing.

(iii) as permitted by Rule 21.1.6 (b). (b) A boat fitted with or carrying on board systems to adjust the forestay while

racing shall declare this to the Rating Authority. This includes a system with the power system disconnected or removed from the boat. The boat may then adjust the forestay while racing, but shall not detach the forestay. Locked conventional turnbuckles that are not adjusted while racing need not be declared.

A boat fitted with or carrying on board systems, to adjust the mast foot while racing shall declare this to the Rating Authority. Unless the boat declares that such systems will not be used while racing, the boat may then adjust the mast foot vertically and/or longitudinally while racing.

21.2 Rig Factor 21.2.1 Rig factor (RF) is calculated by the Rating Authority to evaluate the rig and sail

features of the boat and their character and efficiency when compared to a basic cruising configuration with substantial spars and basic rig controls.

21.2.2 RF may be increased for: fractional, racing and lightweight rigs, high aspect ratio and efficient plan forms, wing and double luff sails, specialised sail stiffening, exotic sailcloth materials, large headboards/cranes, permanently bent or highly controllable spars, hi-tech rigging, exotic rig materials, advanced winch and deck gear arrangements, flush/efficient deck design, and any other feature which increases sailing efficiency that is not already rated through the rated dimensions.

21.2.3 RF may be decreased for less efficient rigs and sail plans, cruising furling sails, motor sailers with large deck houses, cruisers with weight/windage aloft or with basic deck gear only, or any other feature which reduces sailing efficiency that is not already rated through the rated dimensions.

21.2.4 Full rig details shall be supplied at the time of rating application. The Rating Authority reserves the right to apply a high rig factor until full detail is supplied.

21.3 Sheeting of Sails, Sail Definitions, Bowsprits and Spinnaker Poles 21.3.1 No headsail or spinnaker may be sheeted from more than one point on the sail. 21.3.2 All sails shall be set and sheeted in accordance with RRS 50, Setting and Sheeting

Sails, with the following additions: 21.3.3 RRS 50.3(a) is amended to the extent that a spinnaker or a headsail may be tacked

to a bowsprit. 21.3.4 Deleted for 2016 21.3.5 Boats will be rated according to whether they use a spinnaker pole, whisker pole

and/or a bowsprit according to the following configurations: (a) No spinnaker pole (spinnaker tacked on deck) or a centre line bowsprit only. (b) An articulating bowsprit only.

14

(c) Spinnaker pole(s) and/or whisker pole(s) either with or without a bowsprit. 21.4 deleted for 2020 21.5 Mainsails 21.5.1 The following shall be declared: MUW, MTW, MHW. 21.5.2 MUW, MTW and MHW will be shown on the boat’s certificate as the maximum

permitted values. 21.5.3 The highest visible point of a mainsail, mizzen or foremast sail projected at 90° to

the mast spar, shall be set below the upper point, or in the absence of an upper limit mark, below the top of highest sheave used for the halyard.

21.5.4 The aftmost visible point of the mainsail, mizzen or foremast sail projected at 90° to the boom spar, shall be set forward of the outer point, or in the absence of a boom outer limit mark the outer measurement point shall be taken as the aft end of the boom.

21.6 Spinnakers 21.6.1 Boats shall not carry on board more than the number of spinnakers on their IRC

certificate while racing. 21.6.2 Spinnaker area (SPA) shall be calculated from: SPA = ((SLU + SLE)/2) * ((SFL + (4 * SHW))/5) * 0.83 SLU, SLE, SFL and SHW of the largest area spinnaker on board shall be declared.

The calculated area of this spinnaker will be shown on a boat’s certificate as the maximum permitted SPA.

21.7 Headsails 21.7.1 Headsail area (HSA) shall be calculated from:

HSA = 0.0625*HLU*(4*HLP + 6*HHW + 3*HTW + 2*HUW + 0.09) If foot offset is greater than 7.5% of HLP, then foot offset shall be declared and

foot offset shall be added to HLU in the calculation of HSA. 21.7.2 The following shall be declared. HLU, HLP, HHW, HTW, HUW and HLUmax. 21.7.3 HSA, HLU, HLP, HHW, HTW and HUW of the largest area headsail, and HLUmax

will be shown on the boat's certificate. HSA and HLUmax are the maximum permitted values.

21.7.4 Any number of headsails may be set simultaneously when racing under IRC provided that headsail data is measured and declared as defined in Appendix 1.

21.8 Furling Headsails 21.8.1 Boats may apply for a rating credit for using a single roller furling headsail. To be

eligible: (a) A boat shall be fitted with a complete headsail furling system including at

least a drum, furling headfoil, and top swivel. (b) Rated HLP shall be greater than 1.3*J. Exceptionally, this rule shall not apply

to boats of LH greater than 30.5m and with IRC DLR greater than 60. (c) Only a single headsail shall be used while racing, whose HSA shall not be less

than 95% of rated HSA except that alternatively a storm jib (see Appendix 1) may be used.

15

21.8.2 A boat may declare that she may alternatively use a heavy weather jib (see Appendix 1). Provided that she complies with Rule 21.8.1(a) and (b), she will remain eligible for the rating credit but at a reduced rate.

21.8.3 Except in the cases of significant damage or a storm jib or heavy weather jib as appropriate, the same headsail shall be used for all races in any series of races.

21.8.4 Any other headsail may be on board. This Rule may be amended by Notice of Race.

22 EQUIPMENT AND LOADING

22.1 Detachable items 22.1.1 Detachable items (such as but not limited to bunk cushions) permitted by Rule 17

to be aboard for measurement shall be carried in their normal positions while racing. For races requiring compliance with OSR Category 4 or Inshore Racing Category only (or local equivalent), a Notice of Race may state that boats rated with bunk cushions on board may remove the bunk cushions. No compensating weight need be carried.

22.2 Hull Factor 22.2.1 Hull factor (HF) is calculated by the Rating Authority and is an evaluation of

features of the boat and their character and efficiency. 22.2.2 Stripped out interiors, the use of light and hi-tech structures and/or materials,

removal of furniture or other fitted equipment, etc. may lead to the application of higher than standard hull factor to compensate for potential increase in performance. Such features shall be declared to the Rating Authority.

22.2.3 The rated Hull Factor assumes that the boat is fitted out at least to the production specification and materials and/or to the condition when last measured/inspected. This does not negate owners’ responsibilities under Rules 8.9, 22.2.2 and RRS 78.1.

22.3 Moveable Ballast and Variable Ballast 22.3.1 A boat may use moveable ballast and/or variable ballast and any such system

shall be permanently installed and shall be declared to the Rating Authority. RRS 51, Moving Ballast, and RRS 52, Manual Power, are modified in respect of moveable ballast and/or variable ballast systems to the extent required by this class Rule.

22.3.2 List angle is measured in the boat weight condition (see Rule 17) with any additional variable ballast. There is no limit to the list angle with ballast tanks fully filled on one side of the boat and/or with moveable ballast moved fully to one side.

22.3.3 For boats with variable ballast only, the maximum list angle and the maximum volume of water, including plumbing that can be carried on each side of the boat shall be declared.

22.3.4 For boats with moveable ballast only, the maximum list angle shall be declared.

16

22.3.5 For boats with variable ballast AND moveable ballast, the maximum volume of water, including plumbing, that the variable ballast may carry on each side of the boat and the maximum list angle specific to the moveable ballast, with empty variable ballast tanks, shall be declared.

22.3.6 A physical, mechanical limit shall be fitted to all moveable ballast system to prevent it being moved further than the position for the declared list angle. Such a system shall not rely on sensors or measurement to prevent the declared list angle being exceeded unintentionally.

22.3.7 For boats with variable ballast systems that are declared as not used, the system shall be disabled.

22.4 Crew Number/Weight 22.4.1 Boats rated as one-designs, as noted on the boat’s certificate, shall conform with

their one-design class rules in respect of crew number/weight limitations unless freed from this requirement by notice of race. See also Rule 13.7

22.4.2 The crew weight shall not exceed 85kg multiplied by the Crew Number printed on the certificate. This Rule does not apply to short-handed certificates issued under rule 8.2.1.

22.4.3 Rule 22.4 may be amended by Notice of Race. 22.5 Crew Classification 22.5.1 There are no rules on the classification of crew within IRC unless stated in a

Notice of Race. 22.6 Crew Position 22.6.1 RRS 49.2 is modified by deleting “sitting on the deck” in the second sentence.

23 SEAWORTHINESS AND SAFETY

23.1 The issue of a rating certificate does not imply that a boat is necessarily of satisfactory design, safe or seaworthy, nor that a boat complies with any category of Offshore Special Regulations. See Rule 3.

23.2 Race committees may impose limits for race entry on safety grounds at their discretion. An SSS number, specific to the boat, and when data is available IRC/ISO STIX, AVS and IRC/ISO Design Category will be printed on each boat's certificate for the guidance of owners and race organisers.

PART D - IRC, ADVERTISING NOT PERMITTED

25 RULES

25.1 With the exception of Rule 16, Advertising, the IRC Rules Part C shall apply.

26 ADVERTISING

26.1 Competitors’ advertising displayed on the boat is not permitted in accordance with World Sailing Regulation 20, Advertising Code.

17

APPENDIX A - IRC MEASUREMENT DEFINITIONS AND ABBREVIATIONS Measurement Note: World Sailing Equipment Rules of Sailing (ERS) Part II, Definitions, shall

apply to measurement except as stated by IRC Rules or this Appendix. Measurements shall be taken in accordance with ERS Part III, Measurement Rules, Section H.

Terminology: A term used in its defined sense is printed in “bold” type if defined in the ERS. Any abbreviation given below is used in IRC Rules in its defined term unless specified otherwise.

A1 - MISCELLANEOUS

Series date The date on which the first boat of the design or the production series was first launched, whichever is earlier. Series Date does not change if the boat is modified.

Age date The date on which the boat was first launched, or the date on which the

boat was re-launched following any hull shell modification, excluding the transom, whichever is the later.

Hull Shell The hull shell excluding all of the following: any transom, the deck, any

superstructure, the internal structure including any cockpit, fittings associated with these parts and any corrector weights.

Measurement Condition As defined by Rules 17.1. Stored Power Power other than power provided by the crew. Rating Authority As defined in Rule 4.1. Rule Authority As defined in Rule 4.1. RORC The Royal Ocean Racing Club UNCL L’Union National pour la Course au Large.

A2 - HULL & APPENDAGES

LH Hull Length. BO The longitudinal distance between the foremost point on the hull and the

foremost point of the waterline. x The horizontal distance between the waterline and the lowest point on the

stem at a tangent of 450 to the longitudinal axis h The vertical distance between the waterplane and the lowest point on the

stem at a tangent of 450 to the longitudinal axis. SO The longitudinal distance between the aftmost point on the hull and the

aftmost point of the waterline.

18

y The vertical distance between the aftmost point on the hull and the waterplane. In the case of a counter stern, the vertical distance between the aftmost point on the hull below the transom projected to the line of the aftmost point of the hull, and the waterplane.

LWP Waterline length. (LH – BO – SO). Wingspan The maximum horizontal width in any transverse section of any wings

attached to any hull appendage. Bulb Weight The weight of the Bulb and any part of the Keel below the upper surface of

the bulb (including connection plates, under-fin spacers and infills) A3 - LIFTING FOILS No. of Foils: The maximum number of foils that may be actively in use simultaneously. With the boat upright in flotation trim, for each foil: Foil Span: The maximum transverse distance outside the hull shell between any two

points on the foil in its fully extended position. Foil Chord: The maximum longitudinal distance of the foil. The IRC Rating Authority reserves the right to require additional detail to be supplied and also to modify the above definitions on a case by case basis in accordance with IRC Rule 2.8.

A4 - RIG

P The distance between the mainsail (in the case of a schooner, the foremast sail) upper point, and the top of the boom when set at right angles to the mast, or the mainsail tack point whichever is lower, on the mainmast (in the case of a schooner, the foremast). The upper limit mark shall be permanently marked by a 25mm band of contrasting colour. If there is no upper limit mark the upper measurement point shall be taken as the top of the highest sheave used for the halyard. In the case of a gaff rig, the upper measurement point is the peak point of the mainsail or the head point of the topsail if on board.

PY The distance between the mizzen (in the case of a schooner, the mainmast sail) upper point, and the top of the boom when set at right angles to the mast, or the mizzen tack point whichever is lower, on the mizzenmast (in the case of a schooner, the mainmast). The upper limit mark shall be permanently marked by a 25mm band of contrasting colour. If there is no upper limit mark the upper measurement point shall be taken as the top of the highest sheave used for the halyard.

E The outer point distance of a mainsail (or in the case of a schooner, a foremast sail). The outer limit mark shall be permanently marked by a 25mm band of contrasting colour. If there is no outer limit mark the outer measurement point shall be taken to the aft end of the boom. For the measurement of outer point distance, ERS H.4.2 shall not apply. Fittings, local curvature, local cutaway and any increase in the fore/aft dimension of a sail track and/or sail track support, shall be ignored.

19

EY The outer point distance of a mizzen (or in the case of a schooner, a mainsail). The outer limit mark shall be permanently marked by a 25mm band of contrasting colour. If there is no outer limit mark the outer measurement point shall be taken to the aft end of the boom.

Forestay The ERS definition of forestay shall not apply. Forestay is defined as: Permanently attached rigging providing forward support for a mast spar.

FL The forestay length measured from the forward end of J to the forestay rigging point.

J The longitudinal distance between the intersection of the fore side of the mast spar, extended as necessary, and the deck including any superstructure; and the intersection of the centreline of the forestay, extended as necessary, and the deck, or bowsprit spar.

STL The greatest horizontal distance from the forward face of the mast spar, ignoring any fittings and tracks, measured on or near the centreline of the boat, to any of the following:

- the extremity of the spinnaker pole, whisker pole or bowsprit, ignoring any outer limit marks;

- the spinnaker tack point on deck projected vertically as necessary; - if a headsail may be tacked forward of the forestay, the headsail tack point

on deck projected vertically as necessary or to the extremity of the bowsprit.

Whisker Pole A spar attached to the mast spar to set a headsail. ERS F.1.4(d)(ii) does not apply.

Aft rigging: The total number of stays and/or sets of stays connected to the mast spar above the top of the boom set horizontal providing aft support and/or control.

(a) Any pairs of stays attached to the mast spar at the same position port and starboard on the mast spar shall count as one set of stays. Eg, whether there be a single standing backstay or twin running backstays these are counted as one set of stays.

(b) Any deflectors or adjusters attached between the top most stay and the mast spar shall also be counted. Any deflectors or adjusters attached between any other stay and the mast spar with separation from the attachment point of the primary stay of 10% of P or greater shall also be considered as a separate stay for these purposes.

A5 - SAILS – GENERAL

Spinnaker RRS 50.4 shall not apply. A spinnaker is defined as a sail set forward of the foremost mast with half width (measured as a spinnaker) equal to or greater than 75% of foot length and without battens. A spinnaker may be set reefed by any means while racing under IRC provided that when measured in any reefed condition it continues to satisfy the IRC definition of a spinnaker.

20

Headsail RRS 50.4 shall not apply. Any sail tacked down forward of the foremost mast which does not meet the definition of a spinnaker. A headsail may be hoisted from above the forestay rigging point..

Batten Any material added to the sail, as either a removable element, permanent stiffening, or other contrivance, the purpose of which is to support and/or stiffen the sail.

HWJ Heavy Weather Jib. See OSR paragraph 4.26. Storm Jib See OSR paragraph 4.26.

A6 - SAILS - HEADSAILS

HSA The maximum permitted headsail area. HLU The luff length of the largest area headsail on board and which may be used

while racing. HLUmax The longest luff length of any headsail on board and which may be used

while racing. LLY The longest luff length of any mizzen staysail. HLP The luff perpendicular of the largest area headsail on board and which may

be used while racing. LPY The longest luff perpendicular of any mizzen staysail. HHW The half width of the largest area headsail. HTW The three-quarter width of the largest area headsail. HUW The seven-eighths width of the largest area headsail. Foot Offset The maximum offset between the edge of a headsail foot and a straight line

between tack point and clew point. Cutter Rig A cutter rigged boat is any boat that sets more than one headsail when on a

beat to windward while racing. These values will be used in place of standard headsail dimensions where relevant in IRC Rules for a cutter rigged boat.

Cutter Rig HLU Headsail luff length measured parallel to the forestay as the distance from the lowest tack point to the highest head point of any headsails set simultaneously while racing on a beat to windward.

Cutter Rig HLUmax As Cutter Rig HLU. Cutter Rig HLP The shortest distance from the aftmost clew point of any headsail when set

on the centre line of the boat, to the foremost headsail luff which may be set simultaneously while racing on a beat to windward.

Cutter Rig HHW The greater of 50% of Cutter Rig HLP or HHW of the largest area headsail. Cutter Rig HTW The greater of 25% of Cutter Rig HLP or HTW of the largest area headsail. Cutter Rig HUW The greater of 12.5% of Cutter Rig HLP or HUW of the largest area headsail.

21

A7 - SAILS - MAINSAIL

MHW The half width of the mainsail. MTW The three-quarter width of the mainsail. MUW The seven-eighths width of the mainsail.

A8 - SAILS - SPINNAKER SPA The maximum permitted spinnaker area. SLE The leech length of the largest area spinnaker on board. SLU The luff length of the largest area spinnaker on board. SFL The foot length of the largest area spinnaker on board. SHW The half width of the largest area spinnaker on board.

22

APPENDIX B - IRC MEASUREMENT DIAGRAMS FIN KEEL TYPES

Used for guidance only. Select the number that closest resembles the keel on the boat.

23

24

25

26

27

AFT RIGGING

28

Royal Ocean Racing Club (RORC) 20 St James's Place London SW1A 1NN

Tel +44 (0)207 493 2248, Fax +44 (0)207 493 5252 Cowes Office (Race Team) Tel +44 (0)1983 295144

E-Mail racing@rorc.org www.rorc.org

Union Nationale pour la Course au Large (UNCL) 17 rue Henri Bocquillon

75015 PARIS France

Tel +33 (0)1 40 60 43 10 E-mail irc@uncl.com

www.uncl.com

Produced by Seahorse Rating Ltd

(RORC Rating Office) Seahorse Building, Bath Road

Lymington, Hampshire SO41 3SE England

Tel +44 (0)1590 677030, Fax +44 (0)1590 679478 E-Mail info@rorcrating.com

www.rorcrating.com

Published November 2019

Cover image: RORC/Paul Wyeth pwpictures.com

NOTES

\\ Negligible size and weight

\\ Tamper proof record of a sails lifetime history

\\ See how, when and where a sail has been used

\\ Measures: hours in use, UV exposure, G-Force and Flogging

\\ Sail can be tracked, traced and located

\\ App allows users to log, review and export the data recorded

FEATURES

TECHNICAL DETAILS

\\ Sewn attachment to the sail

\\ Fitted during sail manufacture or added as an aftermarket accessory

\\ 7.5 years battery hours depending on use