66
DiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

  • Upload
    lenhu

  • View
    238

  • Download
    3

Embed Size (px)

Citation preview

Page 1: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

DiviComtrade Ion AVC SDStandard Definition H264 Video Encoder

Installation Guide

Rev K

copy 2011 Harmonic Inc

Manual Part No MAN-IONHW-30

copy 2011 Harmonic Inc All rights reserved

Disclaimer

Harmonic reserves the right to alter the equipment specifications and descriptions in this publication without prior notice No part of this publication shall be deemed to be part of any contract or warranty unless specifically incorporated by reference into such contract or warranty The information contained herein is merely descriptive in nature and does not constitute a binding offer for sale of the product described herein Harmonic assumes no responsibility or liability arising from the use of the products described herein except as expressly agreed to in writing by Harmonic The use and purchase of this product do not convey a license under any patent rights copyrights trademark rights or any intellectual property rights of Harmonic Nothing hereunder constitutes a representation or warranty that using any products in the manner described herein will not infringe any patents of third parties

Trademark Acknowledgments

Harmonic and all Harmonic product names are trademarks of Harmonic Inc All other trademarks are the property of their respective owners

Compliance and Approval

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 Subpart B of the Federal Communications Commission (FCC) rules

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment

This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if it is not installed and used in accordance with the instructions in this manual Operation of this equipment in a residential area is likely to cause harmful interference If this occurs the user will be required to correct the interference at his or her own expense

This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions (1) this device may not cause harmful interference and (2) this device must accept any interference received including interference that may cause undesired operation

Connections between the Harmonic equipment and other equipment must be made in a manner that is consistent with maintaining compliance with FCC radio frequency emission limits Modifications to this equipment not expressly approved by Harmonic may void the authority granted to the user by the FCC to operate this equipment

WEEERoHS Compliance Policy

Harmonic Inc intends to comply fully with the European Unionrsquos Directive 200296EC as amended by Directive 2003108EC on Waste Electrical and Electronic Equipment also known as ldquoWEEErdquo and Directive 200295EC as amended on the Restriction of use of Hazardous Substances also known as ldquoRoHSrdquo

Harmonic will ensure that product which cannot be reused will be recycled in compliance with the WEEE Directive To that end users are advised that (1) Harmonic equipment is not to be discarded in household or office garbage (2) Harmonic Inc will pay the freight for shipment of equipment to be disposed of if it is returned to Harmonic (3) customers should call the normal RMA telephone numbers to arrange for such shipment and (4) for additional and updated information on this process customers may consult the Harmonic website httpharmonicinccomah_weee_recyclecfm

Harmonic will ensure that its products will be either reused or recycled in compliance with the WEEE Directive For the latest information concerning Harmonicrsquos WEEERoHS Compliance Policy and its Recycling and Take-Back process please visit our web site

copy 2011 Harmonic Inc All rights reserved

产品中的有毒有害物质或元素的名称及含量表 Names and Contents of the Toxic and Hazardous Substances or Elements in the Products if the Part is Present

该表显示哈雷公司产品中可能含有的有毒有害物质元配件的信息除了来源于元配件供应商的物料成分资料 亦来自其它相关的机构与资料哈雷产品不一定使用这些元配件This table shows those components where hazardous substances may be found in Harmonic products based on among other things material content information provided by third party suppliers These components may or may not be part of the product

除非特殊注明哈雷公司产品的环保使用期限 均为 20 年该环保使用期限的有效条件为必须遵循该产品使用手册的规定对该产品进行使用或存储The Environmental Protective Use Period for Harmonic products is 20 years unless displayed otherwise on the product The EPUP period is valid only when the products are operated or stored as per the conditions specified in the product manual

O 表示在该部件的所有均质材料中此类有毒有害物质的含量均小于 SJT11363-2006 标准所规定的限量

O Indicates the content of the toxic and hazardous substances at the homogeneous material level of the parts is below the limit defined in SJT11363 2006 standard

X 表示至少在该部件的某一均质材料中此类有毒有害物质的含量超出 SJT11363-2006 标准规定的限量

X Indicates that the content of the toxic and hazardous substances in at least one of the homogeneous materials of the parts is above the limit defined in SJT11363 2006 standard

部件名称 (Part name)

有毒有害物质或元素 (Hazardous Substance)

铅(PB)

汞(Hg)

镉(Cd)

六价铬(CrVI)

多溴联苯(PBB)

多溴二苯醚(PBDE)

印刷线路板 (Printed Circuit Assemblies)

X O O O O O

机械组件 (Mechanical Subassemblies)

X O O O O O

光学组件 (Optical Subassemblies)

X O O O O O

电源 (Power Supplies)

X O O O O O

缆线 线束 (Cables harnesses)

X O O O O O

屏幕 显示器 (Screens Monitors)

X O O O O O

金属零件 (Metal Parts)

O O O O O O

塑料 发泡材料 (Plastics foams)

O O O O O O

电池 (Batteries)

X O O O O O

copy 2011 Harmonic Inc All rights reserved

Standards and Agency Approval

The following tables list regulatory standards and agency approvals

North America

Europe

Japan

Australia and New Zealand

Standards Agency Approval

EMI FCC Part 15 Subpart B ICES-003 Issue 2 Class A FCC

Safety UL 60950 CSA 60950 cTUV-us Mark

Standards Agency Approval

EMIEMC EN55022 Class A EN55024 CE

Safety EN 60950 TUV-GS-Mark CE

Standards Agency Approval

EMI VCCI V-3 200004 VCCI

Standards Agency Approval

EMI ASNZS-3548 1995 +A1 1997 +A2 1997 NA

copy 2011 Harmonic Inc All rights reserved

Documentation ConventionsThis manual uses some special symbols and fonts to call your attention to important information The following symbols appear throughout this manual

DANGER The Danger symbol calls your attention to information that if ignored can cause physical harm to you

CAUTION The Caution symbol calls your attention to information that if ignored can adversely affect the performance of your Harmonic product or that can make a procedure needlessly difficult

LASER DANGER The Laser symbol and the Danger alert call your attention to information about the lasers in this product that if ignored can cause physical harm to you

NOTE The Note symbol calls your attention to additional information that you will benefit from heeding It may be used to call attention to an especially important piece of information you need or it may provide additional information that applies in only some carefully delineated circumstances

TIP The Tip symbol calls your attention to parenthetical information that is not necessary for performing a given procedure but which if followed might make the procedure or its subsequent steps easier smoother or more efficient

In addition to these symbols this manual uses the following text conventions

Data Entry indicates text you enter at the keyboard

User Interface indicates a button to click a menu item to select or a key or key sequence to press

Screen Output shows console output or other text that is displayed to you on a computer screen

Bold indicates the definition of a new term

Italics used for emphasis cross-references and hyperlinked cross-references in online documents

Table of Contents

copy 2011 Harmonic Inc 1 Ion AVC SD Version 30 Rev K

Table of Contents

Chapter 1 Preface11 Manual Organization 4

Chapter 2 Introduction21 Operating Environment 522 General Features 523 Video Encoding Features 724 Audio Encoding Features 8

241 Onboard Audio 8242 AIC Card 8

25 AVC Encoding 926 HHP Support 927 Front Panel 9

271 Front Bezel 9272 Local Control Panel 9273 LEDs 10274 Modes of Operation 10

28 Back Panel 11281 AC Power and Fuse 11282 Audio Input Port 11283 Video Input Ports 11284 IP Output Port 12285 Ethernet Management Port 12286 Fault Relay Port 12287 Serial Data Port 12

29 Back Panel LEDs 12291 Main Board LEDs 13292 Audio Port LEDs 13293 Video Lock LEDs 13

Chapter 3 Installation31 Preparation 1432 Unpacking 1433 Installing the Encoder in a Rack 14

331 Rack Guidelines 15332 Chassis Warnings for Rack Mounting and Servicing 15333 Airflow 15334 Attaching the Rack Rails 16335 Mounting the Encoder 17

34 Installing Encoder Software 1735 Cabling the Encoder 18

351 Back Panel 18352 Connecting the Audio Input Cables 18

Table of Contents

copy 2011 Harmonic Inc 2 Ion AVC SD Version 30 Rev K

353 Connecting the Video Input Cables 18354 Connecting the IP Output Cables 19355 Connecting the Ethernet Management Cable 19356 Connecting the AC Power 19

Chapter 4 Operating the Encoder41 Operating with NMX Digital Service Manager 2142 Using the Front Panel 21

421 The Keypad 21422 Front Panel Display 22423 Setting the Encoder Network Properties 22424 Viewing the Encoder MAC Address 23425 Viewing the Encoder Serial Number 23

43 Licensing Information 24

Chapter 5 Maintenance and Troubleshooting51 Air Filters 25

511 Maintaining the Air Filters 25512 Removing and Replacing the Air Filters 26

52 Fuse 26521 Replacing the Fuse 27

53 Contacting Harmonic Support 27

Appendix A Audio and Video SpecificationsA1 AIC Features 28A2 On-board Audio Encoding Features 29

A21 PCM Downmix from 51 31A22 Re-encode Ability 31

A3 MPEG-1Layer II Audio 31A4 Dolby Digital (AC-3) Audio 32A5 Video Specifications 33

Appendix B Encoder SpecificationsB1 Environment Specifications 34B2 Port Specifications 35B3 Port Pinouts 35

B31 Ethernet Management Port 35B32 Fault RelayGPI Ports 37

Appendix C Encoder Back Panel Slot LocationsC1 Adapter Configurations for All Encoders 38

C11 Additional Card Configurations for FLEX-based Encoders 38C12 Viewing the Control Board (CPC) Revision Information 39

Appendix D Boot SequenceD1 Local Control Panel Display Messages during Bootup 40D2 Other Local Control Panel Display Messages 40

D21 Resetting the Encoder 40

Table of Contents

copy 2011 Harmonic Inc 3 Ion AVC SD Version 30 Rev K

D22 Loading New Software 41

Appendix E Wiring the ndash48 VDC Power SupplyE1 Getting Started 42E2 Power Source Specifications 42E3 Overcurrent Protection 42E4 Wiring Requirements 42E5 Power Connector 43E6 Assembling the DC Input Power Cable 43

Appendix F DiviComtrade FLEX Decoding ModuleF1 Introduction 45F2 Video Decoding Specifications 45F3 Audio Passthrough Specifications 46F4 Audio Decode Specifications 47

F41 Decoding Resource Considerations 47F5 Ancillary Data Specifications 49F6 Input Specifications 49F7 Output Specifications 50F8 Environmental and Physical 51F9 Module Slots 51F10 Installing the FLEX Decoding Module 51

F101 Installing a Module 51F11 Cabling the FLEX Module 52F12 Re-Encode Chassis Scenarios 52

F121 2 - Channel 52F122 4 - Channel 54

F13 Configuring the FLEX Module in NMX 54

Appendix G Divicomtrade RF Input CardG1 RF Specifications 55G2 Output Specifications 56G3 Environmental and Physical 56

Appendix H AB Power Input SwitchH1 Introduction 57H2 Card Status 58

Index 59

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 2: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc All rights reserved

Disclaimer

Harmonic reserves the right to alter the equipment specifications and descriptions in this publication without prior notice No part of this publication shall be deemed to be part of any contract or warranty unless specifically incorporated by reference into such contract or warranty The information contained herein is merely descriptive in nature and does not constitute a binding offer for sale of the product described herein Harmonic assumes no responsibility or liability arising from the use of the products described herein except as expressly agreed to in writing by Harmonic The use and purchase of this product do not convey a license under any patent rights copyrights trademark rights or any intellectual property rights of Harmonic Nothing hereunder constitutes a representation or warranty that using any products in the manner described herein will not infringe any patents of third parties

Trademark Acknowledgments

Harmonic and all Harmonic product names are trademarks of Harmonic Inc All other trademarks are the property of their respective owners

Compliance and Approval

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 Subpart B of the Federal Communications Commission (FCC) rules

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment

This equipment generates uses and can radiate radio frequency energy It may cause harmful interference to radio communications if it is not installed and used in accordance with the instructions in this manual Operation of this equipment in a residential area is likely to cause harmful interference If this occurs the user will be required to correct the interference at his or her own expense

This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions (1) this device may not cause harmful interference and (2) this device must accept any interference received including interference that may cause undesired operation

Connections between the Harmonic equipment and other equipment must be made in a manner that is consistent with maintaining compliance with FCC radio frequency emission limits Modifications to this equipment not expressly approved by Harmonic may void the authority granted to the user by the FCC to operate this equipment

WEEERoHS Compliance Policy

Harmonic Inc intends to comply fully with the European Unionrsquos Directive 200296EC as amended by Directive 2003108EC on Waste Electrical and Electronic Equipment also known as ldquoWEEErdquo and Directive 200295EC as amended on the Restriction of use of Hazardous Substances also known as ldquoRoHSrdquo

Harmonic will ensure that product which cannot be reused will be recycled in compliance with the WEEE Directive To that end users are advised that (1) Harmonic equipment is not to be discarded in household or office garbage (2) Harmonic Inc will pay the freight for shipment of equipment to be disposed of if it is returned to Harmonic (3) customers should call the normal RMA telephone numbers to arrange for such shipment and (4) for additional and updated information on this process customers may consult the Harmonic website httpharmonicinccomah_weee_recyclecfm

Harmonic will ensure that its products will be either reused or recycled in compliance with the WEEE Directive For the latest information concerning Harmonicrsquos WEEERoHS Compliance Policy and its Recycling and Take-Back process please visit our web site

copy 2011 Harmonic Inc All rights reserved

产品中的有毒有害物质或元素的名称及含量表 Names and Contents of the Toxic and Hazardous Substances or Elements in the Products if the Part is Present

该表显示哈雷公司产品中可能含有的有毒有害物质元配件的信息除了来源于元配件供应商的物料成分资料 亦来自其它相关的机构与资料哈雷产品不一定使用这些元配件This table shows those components where hazardous substances may be found in Harmonic products based on among other things material content information provided by third party suppliers These components may or may not be part of the product

除非特殊注明哈雷公司产品的环保使用期限 均为 20 年该环保使用期限的有效条件为必须遵循该产品使用手册的规定对该产品进行使用或存储The Environmental Protective Use Period for Harmonic products is 20 years unless displayed otherwise on the product The EPUP period is valid only when the products are operated or stored as per the conditions specified in the product manual

O 表示在该部件的所有均质材料中此类有毒有害物质的含量均小于 SJT11363-2006 标准所规定的限量

O Indicates the content of the toxic and hazardous substances at the homogeneous material level of the parts is below the limit defined in SJT11363 2006 standard

X 表示至少在该部件的某一均质材料中此类有毒有害物质的含量超出 SJT11363-2006 标准规定的限量

X Indicates that the content of the toxic and hazardous substances in at least one of the homogeneous materials of the parts is above the limit defined in SJT11363 2006 standard

部件名称 (Part name)

有毒有害物质或元素 (Hazardous Substance)

铅(PB)

汞(Hg)

镉(Cd)

六价铬(CrVI)

多溴联苯(PBB)

多溴二苯醚(PBDE)

印刷线路板 (Printed Circuit Assemblies)

X O O O O O

机械组件 (Mechanical Subassemblies)

X O O O O O

光学组件 (Optical Subassemblies)

X O O O O O

电源 (Power Supplies)

X O O O O O

缆线 线束 (Cables harnesses)

X O O O O O

屏幕 显示器 (Screens Monitors)

X O O O O O

金属零件 (Metal Parts)

O O O O O O

塑料 发泡材料 (Plastics foams)

O O O O O O

电池 (Batteries)

X O O O O O

copy 2011 Harmonic Inc All rights reserved

Standards and Agency Approval

The following tables list regulatory standards and agency approvals

North America

Europe

Japan

Australia and New Zealand

Standards Agency Approval

EMI FCC Part 15 Subpart B ICES-003 Issue 2 Class A FCC

Safety UL 60950 CSA 60950 cTUV-us Mark

Standards Agency Approval

EMIEMC EN55022 Class A EN55024 CE

Safety EN 60950 TUV-GS-Mark CE

Standards Agency Approval

EMI VCCI V-3 200004 VCCI

Standards Agency Approval

EMI ASNZS-3548 1995 +A1 1997 +A2 1997 NA

copy 2011 Harmonic Inc All rights reserved

Documentation ConventionsThis manual uses some special symbols and fonts to call your attention to important information The following symbols appear throughout this manual

DANGER The Danger symbol calls your attention to information that if ignored can cause physical harm to you

CAUTION The Caution symbol calls your attention to information that if ignored can adversely affect the performance of your Harmonic product or that can make a procedure needlessly difficult

LASER DANGER The Laser symbol and the Danger alert call your attention to information about the lasers in this product that if ignored can cause physical harm to you

NOTE The Note symbol calls your attention to additional information that you will benefit from heeding It may be used to call attention to an especially important piece of information you need or it may provide additional information that applies in only some carefully delineated circumstances

TIP The Tip symbol calls your attention to parenthetical information that is not necessary for performing a given procedure but which if followed might make the procedure or its subsequent steps easier smoother or more efficient

In addition to these symbols this manual uses the following text conventions

Data Entry indicates text you enter at the keyboard

User Interface indicates a button to click a menu item to select or a key or key sequence to press

Screen Output shows console output or other text that is displayed to you on a computer screen

Bold indicates the definition of a new term

Italics used for emphasis cross-references and hyperlinked cross-references in online documents

Table of Contents

copy 2011 Harmonic Inc 1 Ion AVC SD Version 30 Rev K

Table of Contents

Chapter 1 Preface11 Manual Organization 4

Chapter 2 Introduction21 Operating Environment 522 General Features 523 Video Encoding Features 724 Audio Encoding Features 8

241 Onboard Audio 8242 AIC Card 8

25 AVC Encoding 926 HHP Support 927 Front Panel 9

271 Front Bezel 9272 Local Control Panel 9273 LEDs 10274 Modes of Operation 10

28 Back Panel 11281 AC Power and Fuse 11282 Audio Input Port 11283 Video Input Ports 11284 IP Output Port 12285 Ethernet Management Port 12286 Fault Relay Port 12287 Serial Data Port 12

29 Back Panel LEDs 12291 Main Board LEDs 13292 Audio Port LEDs 13293 Video Lock LEDs 13

Chapter 3 Installation31 Preparation 1432 Unpacking 1433 Installing the Encoder in a Rack 14

331 Rack Guidelines 15332 Chassis Warnings for Rack Mounting and Servicing 15333 Airflow 15334 Attaching the Rack Rails 16335 Mounting the Encoder 17

34 Installing Encoder Software 1735 Cabling the Encoder 18

351 Back Panel 18352 Connecting the Audio Input Cables 18

Table of Contents

copy 2011 Harmonic Inc 2 Ion AVC SD Version 30 Rev K

353 Connecting the Video Input Cables 18354 Connecting the IP Output Cables 19355 Connecting the Ethernet Management Cable 19356 Connecting the AC Power 19

Chapter 4 Operating the Encoder41 Operating with NMX Digital Service Manager 2142 Using the Front Panel 21

421 The Keypad 21422 Front Panel Display 22423 Setting the Encoder Network Properties 22424 Viewing the Encoder MAC Address 23425 Viewing the Encoder Serial Number 23

43 Licensing Information 24

Chapter 5 Maintenance and Troubleshooting51 Air Filters 25

511 Maintaining the Air Filters 25512 Removing and Replacing the Air Filters 26

52 Fuse 26521 Replacing the Fuse 27

53 Contacting Harmonic Support 27

Appendix A Audio and Video SpecificationsA1 AIC Features 28A2 On-board Audio Encoding Features 29

A21 PCM Downmix from 51 31A22 Re-encode Ability 31

A3 MPEG-1Layer II Audio 31A4 Dolby Digital (AC-3) Audio 32A5 Video Specifications 33

Appendix B Encoder SpecificationsB1 Environment Specifications 34B2 Port Specifications 35B3 Port Pinouts 35

B31 Ethernet Management Port 35B32 Fault RelayGPI Ports 37

Appendix C Encoder Back Panel Slot LocationsC1 Adapter Configurations for All Encoders 38

C11 Additional Card Configurations for FLEX-based Encoders 38C12 Viewing the Control Board (CPC) Revision Information 39

Appendix D Boot SequenceD1 Local Control Panel Display Messages during Bootup 40D2 Other Local Control Panel Display Messages 40

D21 Resetting the Encoder 40

Table of Contents

copy 2011 Harmonic Inc 3 Ion AVC SD Version 30 Rev K

D22 Loading New Software 41

Appendix E Wiring the ndash48 VDC Power SupplyE1 Getting Started 42E2 Power Source Specifications 42E3 Overcurrent Protection 42E4 Wiring Requirements 42E5 Power Connector 43E6 Assembling the DC Input Power Cable 43

Appendix F DiviComtrade FLEX Decoding ModuleF1 Introduction 45F2 Video Decoding Specifications 45F3 Audio Passthrough Specifications 46F4 Audio Decode Specifications 47

F41 Decoding Resource Considerations 47F5 Ancillary Data Specifications 49F6 Input Specifications 49F7 Output Specifications 50F8 Environmental and Physical 51F9 Module Slots 51F10 Installing the FLEX Decoding Module 51

F101 Installing a Module 51F11 Cabling the FLEX Module 52F12 Re-Encode Chassis Scenarios 52

F121 2 - Channel 52F122 4 - Channel 54

F13 Configuring the FLEX Module in NMX 54

Appendix G Divicomtrade RF Input CardG1 RF Specifications 55G2 Output Specifications 56G3 Environmental and Physical 56

Appendix H AB Power Input SwitchH1 Introduction 57H2 Card Status 58

Index 59

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 3: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc All rights reserved

产品中的有毒有害物质或元素的名称及含量表 Names and Contents of the Toxic and Hazardous Substances or Elements in the Products if the Part is Present

该表显示哈雷公司产品中可能含有的有毒有害物质元配件的信息除了来源于元配件供应商的物料成分资料 亦来自其它相关的机构与资料哈雷产品不一定使用这些元配件This table shows those components where hazardous substances may be found in Harmonic products based on among other things material content information provided by third party suppliers These components may or may not be part of the product

除非特殊注明哈雷公司产品的环保使用期限 均为 20 年该环保使用期限的有效条件为必须遵循该产品使用手册的规定对该产品进行使用或存储The Environmental Protective Use Period for Harmonic products is 20 years unless displayed otherwise on the product The EPUP period is valid only when the products are operated or stored as per the conditions specified in the product manual

O 表示在该部件的所有均质材料中此类有毒有害物质的含量均小于 SJT11363-2006 标准所规定的限量

O Indicates the content of the toxic and hazardous substances at the homogeneous material level of the parts is below the limit defined in SJT11363 2006 standard

X 表示至少在该部件的某一均质材料中此类有毒有害物质的含量超出 SJT11363-2006 标准规定的限量

X Indicates that the content of the toxic and hazardous substances in at least one of the homogeneous materials of the parts is above the limit defined in SJT11363 2006 standard

部件名称 (Part name)

有毒有害物质或元素 (Hazardous Substance)

铅(PB)

汞(Hg)

镉(Cd)

六价铬(CrVI)

多溴联苯(PBB)

多溴二苯醚(PBDE)

印刷线路板 (Printed Circuit Assemblies)

X O O O O O

机械组件 (Mechanical Subassemblies)

X O O O O O

光学组件 (Optical Subassemblies)

X O O O O O

电源 (Power Supplies)

X O O O O O

缆线 线束 (Cables harnesses)

X O O O O O

屏幕 显示器 (Screens Monitors)

X O O O O O

金属零件 (Metal Parts)

O O O O O O

塑料 发泡材料 (Plastics foams)

O O O O O O

电池 (Batteries)

X O O O O O

copy 2011 Harmonic Inc All rights reserved

Standards and Agency Approval

The following tables list regulatory standards and agency approvals

North America

Europe

Japan

Australia and New Zealand

Standards Agency Approval

EMI FCC Part 15 Subpart B ICES-003 Issue 2 Class A FCC

Safety UL 60950 CSA 60950 cTUV-us Mark

Standards Agency Approval

EMIEMC EN55022 Class A EN55024 CE

Safety EN 60950 TUV-GS-Mark CE

Standards Agency Approval

EMI VCCI V-3 200004 VCCI

Standards Agency Approval

EMI ASNZS-3548 1995 +A1 1997 +A2 1997 NA

copy 2011 Harmonic Inc All rights reserved

Documentation ConventionsThis manual uses some special symbols and fonts to call your attention to important information The following symbols appear throughout this manual

DANGER The Danger symbol calls your attention to information that if ignored can cause physical harm to you

CAUTION The Caution symbol calls your attention to information that if ignored can adversely affect the performance of your Harmonic product or that can make a procedure needlessly difficult

LASER DANGER The Laser symbol and the Danger alert call your attention to information about the lasers in this product that if ignored can cause physical harm to you

NOTE The Note symbol calls your attention to additional information that you will benefit from heeding It may be used to call attention to an especially important piece of information you need or it may provide additional information that applies in only some carefully delineated circumstances

TIP The Tip symbol calls your attention to parenthetical information that is not necessary for performing a given procedure but which if followed might make the procedure or its subsequent steps easier smoother or more efficient

In addition to these symbols this manual uses the following text conventions

Data Entry indicates text you enter at the keyboard

User Interface indicates a button to click a menu item to select or a key or key sequence to press

Screen Output shows console output or other text that is displayed to you on a computer screen

Bold indicates the definition of a new term

Italics used for emphasis cross-references and hyperlinked cross-references in online documents

Table of Contents

copy 2011 Harmonic Inc 1 Ion AVC SD Version 30 Rev K

Table of Contents

Chapter 1 Preface11 Manual Organization 4

Chapter 2 Introduction21 Operating Environment 522 General Features 523 Video Encoding Features 724 Audio Encoding Features 8

241 Onboard Audio 8242 AIC Card 8

25 AVC Encoding 926 HHP Support 927 Front Panel 9

271 Front Bezel 9272 Local Control Panel 9273 LEDs 10274 Modes of Operation 10

28 Back Panel 11281 AC Power and Fuse 11282 Audio Input Port 11283 Video Input Ports 11284 IP Output Port 12285 Ethernet Management Port 12286 Fault Relay Port 12287 Serial Data Port 12

29 Back Panel LEDs 12291 Main Board LEDs 13292 Audio Port LEDs 13293 Video Lock LEDs 13

Chapter 3 Installation31 Preparation 1432 Unpacking 1433 Installing the Encoder in a Rack 14

331 Rack Guidelines 15332 Chassis Warnings for Rack Mounting and Servicing 15333 Airflow 15334 Attaching the Rack Rails 16335 Mounting the Encoder 17

34 Installing Encoder Software 1735 Cabling the Encoder 18

351 Back Panel 18352 Connecting the Audio Input Cables 18

Table of Contents

copy 2011 Harmonic Inc 2 Ion AVC SD Version 30 Rev K

353 Connecting the Video Input Cables 18354 Connecting the IP Output Cables 19355 Connecting the Ethernet Management Cable 19356 Connecting the AC Power 19

Chapter 4 Operating the Encoder41 Operating with NMX Digital Service Manager 2142 Using the Front Panel 21

421 The Keypad 21422 Front Panel Display 22423 Setting the Encoder Network Properties 22424 Viewing the Encoder MAC Address 23425 Viewing the Encoder Serial Number 23

43 Licensing Information 24

Chapter 5 Maintenance and Troubleshooting51 Air Filters 25

511 Maintaining the Air Filters 25512 Removing and Replacing the Air Filters 26

52 Fuse 26521 Replacing the Fuse 27

53 Contacting Harmonic Support 27

Appendix A Audio and Video SpecificationsA1 AIC Features 28A2 On-board Audio Encoding Features 29

A21 PCM Downmix from 51 31A22 Re-encode Ability 31

A3 MPEG-1Layer II Audio 31A4 Dolby Digital (AC-3) Audio 32A5 Video Specifications 33

Appendix B Encoder SpecificationsB1 Environment Specifications 34B2 Port Specifications 35B3 Port Pinouts 35

B31 Ethernet Management Port 35B32 Fault RelayGPI Ports 37

Appendix C Encoder Back Panel Slot LocationsC1 Adapter Configurations for All Encoders 38

C11 Additional Card Configurations for FLEX-based Encoders 38C12 Viewing the Control Board (CPC) Revision Information 39

Appendix D Boot SequenceD1 Local Control Panel Display Messages during Bootup 40D2 Other Local Control Panel Display Messages 40

D21 Resetting the Encoder 40

Table of Contents

copy 2011 Harmonic Inc 3 Ion AVC SD Version 30 Rev K

D22 Loading New Software 41

Appendix E Wiring the ndash48 VDC Power SupplyE1 Getting Started 42E2 Power Source Specifications 42E3 Overcurrent Protection 42E4 Wiring Requirements 42E5 Power Connector 43E6 Assembling the DC Input Power Cable 43

Appendix F DiviComtrade FLEX Decoding ModuleF1 Introduction 45F2 Video Decoding Specifications 45F3 Audio Passthrough Specifications 46F4 Audio Decode Specifications 47

F41 Decoding Resource Considerations 47F5 Ancillary Data Specifications 49F6 Input Specifications 49F7 Output Specifications 50F8 Environmental and Physical 51F9 Module Slots 51F10 Installing the FLEX Decoding Module 51

F101 Installing a Module 51F11 Cabling the FLEX Module 52F12 Re-Encode Chassis Scenarios 52

F121 2 - Channel 52F122 4 - Channel 54

F13 Configuring the FLEX Module in NMX 54

Appendix G Divicomtrade RF Input CardG1 RF Specifications 55G2 Output Specifications 56G3 Environmental and Physical 56

Appendix H AB Power Input SwitchH1 Introduction 57H2 Card Status 58

Index 59

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 4: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc All rights reserved

Standards and Agency Approval

The following tables list regulatory standards and agency approvals

North America

Europe

Japan

Australia and New Zealand

Standards Agency Approval

EMI FCC Part 15 Subpart B ICES-003 Issue 2 Class A FCC

Safety UL 60950 CSA 60950 cTUV-us Mark

Standards Agency Approval

EMIEMC EN55022 Class A EN55024 CE

Safety EN 60950 TUV-GS-Mark CE

Standards Agency Approval

EMI VCCI V-3 200004 VCCI

Standards Agency Approval

EMI ASNZS-3548 1995 +A1 1997 +A2 1997 NA

copy 2011 Harmonic Inc All rights reserved

Documentation ConventionsThis manual uses some special symbols and fonts to call your attention to important information The following symbols appear throughout this manual

DANGER The Danger symbol calls your attention to information that if ignored can cause physical harm to you

CAUTION The Caution symbol calls your attention to information that if ignored can adversely affect the performance of your Harmonic product or that can make a procedure needlessly difficult

LASER DANGER The Laser symbol and the Danger alert call your attention to information about the lasers in this product that if ignored can cause physical harm to you

NOTE The Note symbol calls your attention to additional information that you will benefit from heeding It may be used to call attention to an especially important piece of information you need or it may provide additional information that applies in only some carefully delineated circumstances

TIP The Tip symbol calls your attention to parenthetical information that is not necessary for performing a given procedure but which if followed might make the procedure or its subsequent steps easier smoother or more efficient

In addition to these symbols this manual uses the following text conventions

Data Entry indicates text you enter at the keyboard

User Interface indicates a button to click a menu item to select or a key or key sequence to press

Screen Output shows console output or other text that is displayed to you on a computer screen

Bold indicates the definition of a new term

Italics used for emphasis cross-references and hyperlinked cross-references in online documents

Table of Contents

copy 2011 Harmonic Inc 1 Ion AVC SD Version 30 Rev K

Table of Contents

Chapter 1 Preface11 Manual Organization 4

Chapter 2 Introduction21 Operating Environment 522 General Features 523 Video Encoding Features 724 Audio Encoding Features 8

241 Onboard Audio 8242 AIC Card 8

25 AVC Encoding 926 HHP Support 927 Front Panel 9

271 Front Bezel 9272 Local Control Panel 9273 LEDs 10274 Modes of Operation 10

28 Back Panel 11281 AC Power and Fuse 11282 Audio Input Port 11283 Video Input Ports 11284 IP Output Port 12285 Ethernet Management Port 12286 Fault Relay Port 12287 Serial Data Port 12

29 Back Panel LEDs 12291 Main Board LEDs 13292 Audio Port LEDs 13293 Video Lock LEDs 13

Chapter 3 Installation31 Preparation 1432 Unpacking 1433 Installing the Encoder in a Rack 14

331 Rack Guidelines 15332 Chassis Warnings for Rack Mounting and Servicing 15333 Airflow 15334 Attaching the Rack Rails 16335 Mounting the Encoder 17

34 Installing Encoder Software 1735 Cabling the Encoder 18

351 Back Panel 18352 Connecting the Audio Input Cables 18

Table of Contents

copy 2011 Harmonic Inc 2 Ion AVC SD Version 30 Rev K

353 Connecting the Video Input Cables 18354 Connecting the IP Output Cables 19355 Connecting the Ethernet Management Cable 19356 Connecting the AC Power 19

Chapter 4 Operating the Encoder41 Operating with NMX Digital Service Manager 2142 Using the Front Panel 21

421 The Keypad 21422 Front Panel Display 22423 Setting the Encoder Network Properties 22424 Viewing the Encoder MAC Address 23425 Viewing the Encoder Serial Number 23

43 Licensing Information 24

Chapter 5 Maintenance and Troubleshooting51 Air Filters 25

511 Maintaining the Air Filters 25512 Removing and Replacing the Air Filters 26

52 Fuse 26521 Replacing the Fuse 27

53 Contacting Harmonic Support 27

Appendix A Audio and Video SpecificationsA1 AIC Features 28A2 On-board Audio Encoding Features 29

A21 PCM Downmix from 51 31A22 Re-encode Ability 31

A3 MPEG-1Layer II Audio 31A4 Dolby Digital (AC-3) Audio 32A5 Video Specifications 33

Appendix B Encoder SpecificationsB1 Environment Specifications 34B2 Port Specifications 35B3 Port Pinouts 35

B31 Ethernet Management Port 35B32 Fault RelayGPI Ports 37

Appendix C Encoder Back Panel Slot LocationsC1 Adapter Configurations for All Encoders 38

C11 Additional Card Configurations for FLEX-based Encoders 38C12 Viewing the Control Board (CPC) Revision Information 39

Appendix D Boot SequenceD1 Local Control Panel Display Messages during Bootup 40D2 Other Local Control Panel Display Messages 40

D21 Resetting the Encoder 40

Table of Contents

copy 2011 Harmonic Inc 3 Ion AVC SD Version 30 Rev K

D22 Loading New Software 41

Appendix E Wiring the ndash48 VDC Power SupplyE1 Getting Started 42E2 Power Source Specifications 42E3 Overcurrent Protection 42E4 Wiring Requirements 42E5 Power Connector 43E6 Assembling the DC Input Power Cable 43

Appendix F DiviComtrade FLEX Decoding ModuleF1 Introduction 45F2 Video Decoding Specifications 45F3 Audio Passthrough Specifications 46F4 Audio Decode Specifications 47

F41 Decoding Resource Considerations 47F5 Ancillary Data Specifications 49F6 Input Specifications 49F7 Output Specifications 50F8 Environmental and Physical 51F9 Module Slots 51F10 Installing the FLEX Decoding Module 51

F101 Installing a Module 51F11 Cabling the FLEX Module 52F12 Re-Encode Chassis Scenarios 52

F121 2 - Channel 52F122 4 - Channel 54

F13 Configuring the FLEX Module in NMX 54

Appendix G Divicomtrade RF Input CardG1 RF Specifications 55G2 Output Specifications 56G3 Environmental and Physical 56

Appendix H AB Power Input SwitchH1 Introduction 57H2 Card Status 58

Index 59

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 5: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc All rights reserved

Documentation ConventionsThis manual uses some special symbols and fonts to call your attention to important information The following symbols appear throughout this manual

DANGER The Danger symbol calls your attention to information that if ignored can cause physical harm to you

CAUTION The Caution symbol calls your attention to information that if ignored can adversely affect the performance of your Harmonic product or that can make a procedure needlessly difficult

LASER DANGER The Laser symbol and the Danger alert call your attention to information about the lasers in this product that if ignored can cause physical harm to you

NOTE The Note symbol calls your attention to additional information that you will benefit from heeding It may be used to call attention to an especially important piece of information you need or it may provide additional information that applies in only some carefully delineated circumstances

TIP The Tip symbol calls your attention to parenthetical information that is not necessary for performing a given procedure but which if followed might make the procedure or its subsequent steps easier smoother or more efficient

In addition to these symbols this manual uses the following text conventions

Data Entry indicates text you enter at the keyboard

User Interface indicates a button to click a menu item to select or a key or key sequence to press

Screen Output shows console output or other text that is displayed to you on a computer screen

Bold indicates the definition of a new term

Italics used for emphasis cross-references and hyperlinked cross-references in online documents

Table of Contents

copy 2011 Harmonic Inc 1 Ion AVC SD Version 30 Rev K

Table of Contents

Chapter 1 Preface11 Manual Organization 4

Chapter 2 Introduction21 Operating Environment 522 General Features 523 Video Encoding Features 724 Audio Encoding Features 8

241 Onboard Audio 8242 AIC Card 8

25 AVC Encoding 926 HHP Support 927 Front Panel 9

271 Front Bezel 9272 Local Control Panel 9273 LEDs 10274 Modes of Operation 10

28 Back Panel 11281 AC Power and Fuse 11282 Audio Input Port 11283 Video Input Ports 11284 IP Output Port 12285 Ethernet Management Port 12286 Fault Relay Port 12287 Serial Data Port 12

29 Back Panel LEDs 12291 Main Board LEDs 13292 Audio Port LEDs 13293 Video Lock LEDs 13

Chapter 3 Installation31 Preparation 1432 Unpacking 1433 Installing the Encoder in a Rack 14

331 Rack Guidelines 15332 Chassis Warnings for Rack Mounting and Servicing 15333 Airflow 15334 Attaching the Rack Rails 16335 Mounting the Encoder 17

34 Installing Encoder Software 1735 Cabling the Encoder 18

351 Back Panel 18352 Connecting the Audio Input Cables 18

Table of Contents

copy 2011 Harmonic Inc 2 Ion AVC SD Version 30 Rev K

353 Connecting the Video Input Cables 18354 Connecting the IP Output Cables 19355 Connecting the Ethernet Management Cable 19356 Connecting the AC Power 19

Chapter 4 Operating the Encoder41 Operating with NMX Digital Service Manager 2142 Using the Front Panel 21

421 The Keypad 21422 Front Panel Display 22423 Setting the Encoder Network Properties 22424 Viewing the Encoder MAC Address 23425 Viewing the Encoder Serial Number 23

43 Licensing Information 24

Chapter 5 Maintenance and Troubleshooting51 Air Filters 25

511 Maintaining the Air Filters 25512 Removing and Replacing the Air Filters 26

52 Fuse 26521 Replacing the Fuse 27

53 Contacting Harmonic Support 27

Appendix A Audio and Video SpecificationsA1 AIC Features 28A2 On-board Audio Encoding Features 29

A21 PCM Downmix from 51 31A22 Re-encode Ability 31

A3 MPEG-1Layer II Audio 31A4 Dolby Digital (AC-3) Audio 32A5 Video Specifications 33

Appendix B Encoder SpecificationsB1 Environment Specifications 34B2 Port Specifications 35B3 Port Pinouts 35

B31 Ethernet Management Port 35B32 Fault RelayGPI Ports 37

Appendix C Encoder Back Panel Slot LocationsC1 Adapter Configurations for All Encoders 38

C11 Additional Card Configurations for FLEX-based Encoders 38C12 Viewing the Control Board (CPC) Revision Information 39

Appendix D Boot SequenceD1 Local Control Panel Display Messages during Bootup 40D2 Other Local Control Panel Display Messages 40

D21 Resetting the Encoder 40

Table of Contents

copy 2011 Harmonic Inc 3 Ion AVC SD Version 30 Rev K

D22 Loading New Software 41

Appendix E Wiring the ndash48 VDC Power SupplyE1 Getting Started 42E2 Power Source Specifications 42E3 Overcurrent Protection 42E4 Wiring Requirements 42E5 Power Connector 43E6 Assembling the DC Input Power Cable 43

Appendix F DiviComtrade FLEX Decoding ModuleF1 Introduction 45F2 Video Decoding Specifications 45F3 Audio Passthrough Specifications 46F4 Audio Decode Specifications 47

F41 Decoding Resource Considerations 47F5 Ancillary Data Specifications 49F6 Input Specifications 49F7 Output Specifications 50F8 Environmental and Physical 51F9 Module Slots 51F10 Installing the FLEX Decoding Module 51

F101 Installing a Module 51F11 Cabling the FLEX Module 52F12 Re-Encode Chassis Scenarios 52

F121 2 - Channel 52F122 4 - Channel 54

F13 Configuring the FLEX Module in NMX 54

Appendix G Divicomtrade RF Input CardG1 RF Specifications 55G2 Output Specifications 56G3 Environmental and Physical 56

Appendix H AB Power Input SwitchH1 Introduction 57H2 Card Status 58

Index 59

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 6: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Table of Contents

copy 2011 Harmonic Inc 1 Ion AVC SD Version 30 Rev K

Table of Contents

Chapter 1 Preface11 Manual Organization 4

Chapter 2 Introduction21 Operating Environment 522 General Features 523 Video Encoding Features 724 Audio Encoding Features 8

241 Onboard Audio 8242 AIC Card 8

25 AVC Encoding 926 HHP Support 927 Front Panel 9

271 Front Bezel 9272 Local Control Panel 9273 LEDs 10274 Modes of Operation 10

28 Back Panel 11281 AC Power and Fuse 11282 Audio Input Port 11283 Video Input Ports 11284 IP Output Port 12285 Ethernet Management Port 12286 Fault Relay Port 12287 Serial Data Port 12

29 Back Panel LEDs 12291 Main Board LEDs 13292 Audio Port LEDs 13293 Video Lock LEDs 13

Chapter 3 Installation31 Preparation 1432 Unpacking 1433 Installing the Encoder in a Rack 14

331 Rack Guidelines 15332 Chassis Warnings for Rack Mounting and Servicing 15333 Airflow 15334 Attaching the Rack Rails 16335 Mounting the Encoder 17

34 Installing Encoder Software 1735 Cabling the Encoder 18

351 Back Panel 18352 Connecting the Audio Input Cables 18

Table of Contents

copy 2011 Harmonic Inc 2 Ion AVC SD Version 30 Rev K

353 Connecting the Video Input Cables 18354 Connecting the IP Output Cables 19355 Connecting the Ethernet Management Cable 19356 Connecting the AC Power 19

Chapter 4 Operating the Encoder41 Operating with NMX Digital Service Manager 2142 Using the Front Panel 21

421 The Keypad 21422 Front Panel Display 22423 Setting the Encoder Network Properties 22424 Viewing the Encoder MAC Address 23425 Viewing the Encoder Serial Number 23

43 Licensing Information 24

Chapter 5 Maintenance and Troubleshooting51 Air Filters 25

511 Maintaining the Air Filters 25512 Removing and Replacing the Air Filters 26

52 Fuse 26521 Replacing the Fuse 27

53 Contacting Harmonic Support 27

Appendix A Audio and Video SpecificationsA1 AIC Features 28A2 On-board Audio Encoding Features 29

A21 PCM Downmix from 51 31A22 Re-encode Ability 31

A3 MPEG-1Layer II Audio 31A4 Dolby Digital (AC-3) Audio 32A5 Video Specifications 33

Appendix B Encoder SpecificationsB1 Environment Specifications 34B2 Port Specifications 35B3 Port Pinouts 35

B31 Ethernet Management Port 35B32 Fault RelayGPI Ports 37

Appendix C Encoder Back Panel Slot LocationsC1 Adapter Configurations for All Encoders 38

C11 Additional Card Configurations for FLEX-based Encoders 38C12 Viewing the Control Board (CPC) Revision Information 39

Appendix D Boot SequenceD1 Local Control Panel Display Messages during Bootup 40D2 Other Local Control Panel Display Messages 40

D21 Resetting the Encoder 40

Table of Contents

copy 2011 Harmonic Inc 3 Ion AVC SD Version 30 Rev K

D22 Loading New Software 41

Appendix E Wiring the ndash48 VDC Power SupplyE1 Getting Started 42E2 Power Source Specifications 42E3 Overcurrent Protection 42E4 Wiring Requirements 42E5 Power Connector 43E6 Assembling the DC Input Power Cable 43

Appendix F DiviComtrade FLEX Decoding ModuleF1 Introduction 45F2 Video Decoding Specifications 45F3 Audio Passthrough Specifications 46F4 Audio Decode Specifications 47

F41 Decoding Resource Considerations 47F5 Ancillary Data Specifications 49F6 Input Specifications 49F7 Output Specifications 50F8 Environmental and Physical 51F9 Module Slots 51F10 Installing the FLEX Decoding Module 51

F101 Installing a Module 51F11 Cabling the FLEX Module 52F12 Re-Encode Chassis Scenarios 52

F121 2 - Channel 52F122 4 - Channel 54

F13 Configuring the FLEX Module in NMX 54

Appendix G Divicomtrade RF Input CardG1 RF Specifications 55G2 Output Specifications 56G3 Environmental and Physical 56

Appendix H AB Power Input SwitchH1 Introduction 57H2 Card Status 58

Index 59

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 7: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Table of Contents

copy 2011 Harmonic Inc 2 Ion AVC SD Version 30 Rev K

353 Connecting the Video Input Cables 18354 Connecting the IP Output Cables 19355 Connecting the Ethernet Management Cable 19356 Connecting the AC Power 19

Chapter 4 Operating the Encoder41 Operating with NMX Digital Service Manager 2142 Using the Front Panel 21

421 The Keypad 21422 Front Panel Display 22423 Setting the Encoder Network Properties 22424 Viewing the Encoder MAC Address 23425 Viewing the Encoder Serial Number 23

43 Licensing Information 24

Chapter 5 Maintenance and Troubleshooting51 Air Filters 25

511 Maintaining the Air Filters 25512 Removing and Replacing the Air Filters 26

52 Fuse 26521 Replacing the Fuse 27

53 Contacting Harmonic Support 27

Appendix A Audio and Video SpecificationsA1 AIC Features 28A2 On-board Audio Encoding Features 29

A21 PCM Downmix from 51 31A22 Re-encode Ability 31

A3 MPEG-1Layer II Audio 31A4 Dolby Digital (AC-3) Audio 32A5 Video Specifications 33

Appendix B Encoder SpecificationsB1 Environment Specifications 34B2 Port Specifications 35B3 Port Pinouts 35

B31 Ethernet Management Port 35B32 Fault RelayGPI Ports 37

Appendix C Encoder Back Panel Slot LocationsC1 Adapter Configurations for All Encoders 38

C11 Additional Card Configurations for FLEX-based Encoders 38C12 Viewing the Control Board (CPC) Revision Information 39

Appendix D Boot SequenceD1 Local Control Panel Display Messages during Bootup 40D2 Other Local Control Panel Display Messages 40

D21 Resetting the Encoder 40

Table of Contents

copy 2011 Harmonic Inc 3 Ion AVC SD Version 30 Rev K

D22 Loading New Software 41

Appendix E Wiring the ndash48 VDC Power SupplyE1 Getting Started 42E2 Power Source Specifications 42E3 Overcurrent Protection 42E4 Wiring Requirements 42E5 Power Connector 43E6 Assembling the DC Input Power Cable 43

Appendix F DiviComtrade FLEX Decoding ModuleF1 Introduction 45F2 Video Decoding Specifications 45F3 Audio Passthrough Specifications 46F4 Audio Decode Specifications 47

F41 Decoding Resource Considerations 47F5 Ancillary Data Specifications 49F6 Input Specifications 49F7 Output Specifications 50F8 Environmental and Physical 51F9 Module Slots 51F10 Installing the FLEX Decoding Module 51

F101 Installing a Module 51F11 Cabling the FLEX Module 52F12 Re-Encode Chassis Scenarios 52

F121 2 - Channel 52F122 4 - Channel 54

F13 Configuring the FLEX Module in NMX 54

Appendix G Divicomtrade RF Input CardG1 RF Specifications 55G2 Output Specifications 56G3 Environmental and Physical 56

Appendix H AB Power Input SwitchH1 Introduction 57H2 Card Status 58

Index 59

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 8: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Table of Contents

copy 2011 Harmonic Inc 3 Ion AVC SD Version 30 Rev K

D22 Loading New Software 41

Appendix E Wiring the ndash48 VDC Power SupplyE1 Getting Started 42E2 Power Source Specifications 42E3 Overcurrent Protection 42E4 Wiring Requirements 42E5 Power Connector 43E6 Assembling the DC Input Power Cable 43

Appendix F DiviComtrade FLEX Decoding ModuleF1 Introduction 45F2 Video Decoding Specifications 45F3 Audio Passthrough Specifications 46F4 Audio Decode Specifications 47

F41 Decoding Resource Considerations 47F5 Ancillary Data Specifications 49F6 Input Specifications 49F7 Output Specifications 50F8 Environmental and Physical 51F9 Module Slots 51F10 Installing the FLEX Decoding Module 51

F101 Installing a Module 51F11 Cabling the FLEX Module 52F12 Re-Encode Chassis Scenarios 52

F121 2 - Channel 52F122 4 - Channel 54

F13 Configuring the FLEX Module in NMX 54

Appendix G Divicomtrade RF Input CardG1 RF Specifications 55G2 Output Specifications 56G3 Environmental and Physical 56

Appendix H AB Power Input SwitchH1 Introduction 57H2 Card Status 58

Index 59

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 9: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 4 Ion AVC SD Version 30 Rev K

Chapter 1Preface

This manual describes the Ion AVC SD Standard H264 Video Encoder

11 Manual OrganizationThis manual contains the following chapters

Chapter 2 Introduction introduces the encoder and describes its features

Chapter 3 Installation provides a hardware overview including a description of the back panel ports connector specifications and rack-mounting instructions

Chapter 4 Operating the Encoder describes how to begin configuring the encoder using NMX or the front panel

Chapter 5 Maintenance and Troubleshooting describes maintenance and what to do in the event of problems

Appendix A Audio and Video Specifications provides specifications for audio and video encoding

Appendix B Encoder Specifications describes specifications and physical characteristics of the back panel ports and port pinouts environment specifications and input and output specifications

Appendix C Encoder Back Panel Slot Locations shows the numbering of the back panel slots NMX uses the slot number to differentiate between cards of the same type within the encoder

Appendix D Boot Sequence describes the encoder boot sequence including the messages that appear on the front panel

Appendix E Wiring the ndash48 VDC Power Supply describes how to wire the (optional) 48 VDC power supply

Appendix F DiviComtrade FLEX Decoding Module provides details about the DiviCom FLEX decoding module

Appendix G Divicomtrade RF Input Card provides specifications for the DiviCom RF Input Card

Appendix H AB Power Input Switch provides specifications for the optional AB Power Input Switch

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 10: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 5 Ion AVC SD Version 30 Rev K

Chapter 2Introduction

The DiviCom Ion AVC SD Standard H264 Video Encoder uses the MPEG-4 Part 10 (AVC) also known as ITU-T H264 standard to compress its video inputs It accepts up to four standard definition (SD) video inputs and up to three stereo pairs of embedded digital audio (per video) inputs The encoder output is MPEG-2 Transport Stream (TS) transmitted over IP transport

This chapter describes

The environment in which you can operate the Ion AVC SD

General features

Video encoding features

Audio encoding features

Support for AVC and HHP

The front and back panels

21 Operating EnvironmentThe encoder operates under the control of NMXtrade Digital Service Manager NMX manages multiple Ion AVC SD encoders and other devices NMX provides full configuration of the Ion AVC SD platform ports services and PSI as well as alarm management You configure a few initial network settings from the front panel of the encoder The encoder operates within an IP environment therefore encoders and multiplexers do not need to be in the same physical location Harmonic recommends discussing your planned network architecture with a Harmonic representative before implementation

22 General Features Table 2-1 describes general features supported by the Ion AVC SD See the following tables for more information about video and audio compression

NOTE Internal Ion encoder audio boards only support one audio codec at a time The three pairs of audio channels must use AC-3 MPEG2 or AAC audio not a mixture of both If more than one codec is required you must use another audio adapter Passthrough can be conducted on any codec For example you can do MPEG-1 Layer II compression on the first pair and AC-3 passthrough on the second pair

Table 2-1 General Features

Feature Description

Hardware

Chassis Compact 1-RU Mounts in Electronic Industries Association (EIA) standard rack

Local control panel Two-line 20-character vacuum fluorescent display (VFD) 24-button keypad (includes Help key) Four status LEDs

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 11: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 2 Introduction General Features

copy 2011 Harmonic Inc 6 Ion AVC SD Version 30 Rev K

Software

Control NMX Digital Service Manager Front control panel (for setting management IP address)

Upgrades From NMX See the NMX online help for details

Video input Up to four standard definition (SD) video encoders per chassis Accepts 625- and 525-line serial digital video

Audio input AIC Digital or analog stereo inputs Two stereo pairs per AIC Complete embedded audio extraction of eight pairs from four

groups from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II 2 stereo compression

Dolby Digitala (AC-3) stereo compression

Dolby Digitala (20 or 51) passthrough

AACHE AACb 20 audio compression Dolby Digital Plus passthrough

On-board audioe Embedded multichannel or multiple digital stereo inputs only

Into three stereo pairsc

Complete embedded audio extraction of three pairs from serial digital video input (48 kHz synchronous to video only)

MPEG-1Layer II stereo compression

Dolby Digitalb (AC-3) 20 stereo compression

Dolby Digitalb (20 or 51) passthrough

AACHE AACd multiple 20 audio compression with MPEG-2 or MPEG-4 encapsulation

IP output One 101001000 Base-T port with second redundant channelconnector

Dual-mode IP output or manual channel switch for redundancy Hotwarm standalone IP channel redundancy Same-source IP output support Automatic port redundancy UDP and RTP encapsulation support Unicast and multicast address support Ping and ARP support Single-program transport stream (SPTS) and multiple-program

transport stream (MPTS) outputs Null packets can be preserved to match the exact rate of SPTS

(video server integration) Connector type RJ-45 Harmonic Heartbeat Protocol (HHP) redundancy protection

PSI support Generated by NMX when managed by NMX

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 12: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 2 Introduction Video Encoding Features

copy 2011 Harmonic Inc 7 Ion AVC SD Version 30 Rev K

23 Video Encoding Features Table 2-2 describes video encoding features supported by the encoder

Table 2-2 Video Encoding Features

Feature Support

Input format Standard definition serial digital interface (SD-SDI)

Video format NTSC or PAL over SDI (43 and 169 aspect rations)

Encoding mode AVC (MPEG-4 Part 10) Main Profile

Video processing PSIP tables spooling

Horizontal resolutions

720 704 640 544 528 480 352

Frame rates 25 Hz and 2997 Hz

Picture-in-picture MSTV

625-line VBI Support for

525-line VBI Support for

Alarms Current and history alarm logs in NMX Alarm Manager SNMP alarm forwarding

IRIStrade Support Data reporting (losscorrupted and silent audio) of input audio

a Dolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trade-marks of Dolby Laboratories

b The AIC uses an implementation of AACHE AAC also known as aacPlustrade developed by Coding Technologies (httpwwwcodingtechnologiescom) Trademarks of Coding Technologies GmbH are the property of Dolby Laboratories All rights reserved

c Surround mix on three AES3 signals is with channels mapped per SMPTE 320M (LR CLfe LsRs)

d The AHC-RAC and onboard audio use implementations of AACHE AAC by Fraunhofer IIS

e Embedded audio only To receive nonembedded audio an AHC-BASE card must also be installedDolby is a registered trademark of Dolby Laboratories AC-3 and Dolby E are trademarks of Dolby Laboratories

Teletext Standard and dynamic WSS AFD VPS

EIA-608-B Captions encapsulated per ATSC Captions encapsulated per North American DBS 608 to 708 conversion

Table 2-1 General Features continued

Feature Description

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 13: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 2 Introduction Audio Encoding Features

copy 2011 Harmonic Inc 8 Ion AVC SD Version 30 Rev K

24 Audio Encoding Features This section describes both the onboard audio and AIC card features

241 Onboard AudioTable 2-3 describes audio encoding features supported by the encoder equipped with the only with onboard audio

Table 2-3 Audio Encoding Features Onboard Audio

Feature Support

Digitial Input

Input format

Audio encoding format

242 AIC CardTable 2-4 describes audio encoding features supported by the encoder equipped with an AIC adapter

Table 2-4 Audio Encoding Features AIC

Feature Support

Stereo pairs

Input format

Analog reference level specification

Reference levels in the range -10 dBu to +4 dBu may be specified in 05 dBu steps Alignment tone at reference level is placed at -20 dBFS per SMPTE RP155

Audio encoding format

THD+noise 00032 measured at ndash3bBFS

Completely embedded audio extraction of three pairs from six groups from serial digital video input (48kHz synchronous to video only)

Embedded from SDI (synchronous to video)

Multiple MPEG-1 Layer II 20 (stereo) compression AACHE AAC multiple 20 audio compression with either

MPEG-2 or MPEG-4 encapsulation Dolby Digital (AC-3) or multiple 20 compression Dolby Digital (20 or 51) passthrough Single channel dual stereo and joint stereo (MPEG-1 Layer II

and AACHE AAC only)

Up to 10 stereo pairs Two stereo pairs per AIC

Digital AES3 or SPDIF Analog balanced or unbalanced Embedded from SDI (video)

MPEG-1Layer II 20 (stereo) compression Dolby Digital (AC-3) 20 stereo compression Dolby Sigital 20 or 51 passthrough AACHE AAC 20 stereo compression Single channel dual stereo and joint stereo (MPEG-1Layer II

and AACHE AAC only) Single PID per Channel support with MPEG-1 Layer II

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 14: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 2 Introduction AVC Encoding

copy 2011 Harmonic Inc 9 Ion AVC SD Version 30 Rev K

25 AVC EncodingThe Ion AVC SD video compression complies with the AVC (MPEG-4 Part 10) Main Profile

26 HHP Support Harmonic Heartbeat Protocol (HHP) is a proprietary Harmonic protocol used to prevent duplicate IP output after a redundancy switch and to initiate a redundancy switch in some 1x1 hot backup scenarios HHP packets are sent over a unique multicast address on the video IP network

In some redundancy switches NMX may not be able to shut down the IP output from the primary device For example if the connection between the device and NMX is lost NMX issues a time-out alarm for the device and provisions the backup device with the circuits from the primary device However the primary device may still be operating normally even though it lost communication with NMX In this case you now have two devices sending the same output

To prevent this scenario enable HHP When you enable HHP a backup device taking over in a redundancy switching event will send a command (over a unique multicast address on the video IP network) to turn off the outputs of the formerly active device During a redundancy switch the backup device assumes all responsibilities of the primary device including sending HHP messages at the same multicast address

If a primary device detects HHP messages sent to its multicast IP address it immediately backs off and stops sending output This leaves the backup device free to operate without the primary device sending the same output

In 1x1 hot backup configurations the HHP protocol can also initiate a redundancy switch In this case the backup device monitors the primary device by listening for HHP messages If the backup device does not detect an HHP message from the primary device during a specified interval it initiates a redundancy switch and assumes operation as the primary device

27 Front Panel Figure 2-1 shows the front panel of the DiviCom Ion AVC SD encoder

Figure 2-1 Front panel

271 Front Bezel The encoder has a detachable front bezel that snaps on top of the local control panel and provides access to the reusable air filters See 51 Air Filters on page 25 for information about cleaning the air filters

272 Local Control Panel The local control panel allows configuration of the initial network settings for the encoder From the front panel you can set the encoder IP address subnet mask and default gateway and view the encoder MAC address

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 15: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 2 Introduction Front Panel

copy 2011 Harmonic Inc 10 Ion AVC SD Version 30 Rev K

273 LEDs The four LEDs on the front panel indicate the operational state of the encoder Table 2-5 describes the front panel LEDs

Table 2-5 Front Panel LEDs

LED Color Description

Power Yellow The Power LED is yellow while the encoder initializes after startup

Green The Power LED turns green when the encoder initialization is complete and the management interface is enabled and ready

Fault Red The Fault LED lights when the application software detects an alarm

Local Yellow The Local LED lights when the encoder is operating in local mode

Activity Yellow The Activity LED lights when the encoder generates an MPEG-2 transport stream It blinks slowly when MPEG packets are being transmitted steadily It blinks fast or intermittently when the transmission rate is slow or intermittent

274 Modes of OperationThere are three modes of operation on the encoder and they are are set globally through the NMX interface for all encoder platforms and locally on the Stand Alone GUI (SAG) as well

Default Mode

Verbose Front Panel Mode

NMX Control Over Second Line

2741 Default Mode

The default mode (with no provision from the NMX application) is the default mode For more information on the default mode refer to the NMX online help

2742 Verbose Front Panel

The front panel displays the device name on line one and either the card number or Broadcast Operations Control (BOC) as well as the (sliding) service name on the second line For more information on the verbose front panel refer to the NMX online help

2743 NMX Control Over Second Line

Under this option you can set the front panel classic display mode as well as the channel name and bitrate For more information on the NMX control on the second line refer to the NMX online help

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 16: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 2 Introduction Back Panel

copy 2011 Harmonic Inc 11 Ion AVC SD Version 30 Rev K

28 Back Panel The back panel contains the following elements as shown in Figure 2-2

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input PortsExpansion Slot

NOTE See Table C-1 on page 38 for information on which cardsmodules are supported in your back panel

Figure 2-2 Back panel

281 AC Power and Fuse The AC power plug accommodates standard IEC 120 VAC and 250 VAC power cords The chassis does not have a power switch The unit powers on automatically when you plug it in

See 356 Connecting the AC Power on page 19 for cabling instructions

The fuse panel is located beside the power plug The encoder requires one slow blow 40 A 250 V fuse 5 x 20 mm See 52 Fuse on page 26 for replacement instructions

282 Audio Input PortThe Ion AVC SD can be configured with a combination of onboard audio and AIC cards

283 Video Input Ports The back panel contains up to four video input ports These are BNC coaxial ports that support standard definition serial digital video input Each serial digital video input can carry up to three stereo pairs of embedded digital audio

Each video input port connects internally to a video processing card (VPC)) The video processing cards are not visible from the encoder back panel

See 353 Connecting the Video Input Cables on page 18 for cabling instructions

AC power plug and fuse Up to four video input ports Video lock LEDs Up to two stereo digital audio input

ports per AIC card Fault relay port Fault and Locator LEDs

Serial data input port One 10100 Base-T Ethernet

management port One 101001000 Base-T Fast Ethernet

output port with second redundant channel and connector

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 17: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 12 Ion AVC SD Version 30 Rev K

284 IP Output Port One 101001000 Base-T Ethernet port provides two redundant IP output channels The two RJ-45 connectors are labeled GbE PRI and BKUP

The IP output port supports manual redundancy The port also supports hotwarm standalone redundancy when the primary IP data channel detects a cable disconnection the primary channel stops outputting and the backup channel takes over

In manual redundancy you can enable one channel or both channels If you enable one channel you must manually switch to the other channel after a service-affecting alarm If you enable both channels the encoder outputs the same data from both channels

See 354 Connecting the IP Output Cables on page 19 for cabling instructions Set the IP address and other network information for the IP output ports using NMX

285 Ethernet Management Port The Ethernet management port labeled ETH is 10100 Base-T and uses an RJ-45UTP cable to connect to an Ethernet network See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions See B31 Ethernet Management Port on page 35 for pinout information

286 Fault Relay Port The fault relay port connects to a Form C relay that can switch up to 025 amps at 30 VDC See B32 Fault RelayGPI Ports on page 37 for port pinout and additional information

The encoder energizes the fault relay during normal operation The fault condition is indicated in the same way as the encoderrsquos powered-off condition which is with the relay de-energized You can use this method to correctly identify a power supply failure or loss of input power The signals are normally open or normally closed

NOTE Any alarm causes the fault relay to change to the fault state When multiple alarms accumulate all alarms must be active for the relay state to change

287 Serial Data Port The serial data port may be supported at some future time

29 Back Panel LEDs The following sections describe the back panel LEDs and their functions

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 18: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 2 Introduction Back Panel LEDs

copy 2011 Harmonic Inc 13 Ion AVC SD Version 30 Rev K

291 Main Board LEDsThe back panel contains two LEDs on the main board Table 2-6 describes the LEDs located on the main board

Table 2-6 Rear Panel Main Board LEDs

LED Color Description

Locator Blue The Locator LED lights when this encoder is enabled through NMX Use the Locator LED to help you identify a specific chassis in a rack

Fault Red The Fault LED lights when the application software detects an alarm The front panel and back panel Fault LEDs light at the same time

292 Audio Port LEDs Each AIC contains a status LED Table 2-7 describes the LED located on each AIC

Table 2-7 Rear Panel Audio Port LEDs

LED Color Description

STAT Blue The Audio Port LED is on during bootup as the audio input card comes online The LED is off during normal operation

293 Video Lock LEDs Each video port has an associated Video Lock LED Table 2-8 describes the LED located on each video port

Table 2-8 Rear Panel Video Lock LEDs

LED Color Description

Video 1Video 2

Green When illuminated and steady the Video Lock LED indicates that the video signal is locked When off the Video Lock LED indicates that the encoder has lost video sync

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 19: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 14 Ion AVC SD Version 30 Rev K

Chapter 3Installation

This chapter provides detailed instructions for installing a DiviCom Ion AVC SD encoder in a standard 19-inch rack and connecting cables

The chapter describes

How to prepare and unpack the Ion AVC SD

How to install the encoder in a rack

How to update the encoder software

How to connect the cables

31 PreparationYou need a Phillips screwdriver to mount the encoder in a standard 19-inch rack Harmonic ships the necessary rack-mount screws and rack rails

32 Unpacking The encoder comes in a specially designed shipping container that ensures the integrity of your encoder hardware during shipping and handling To avoid damage to the component follow the unpacking instructions that come with the encoder

When you unpack the encoder you should find the following items

Encoder

Standard IEC power cord

Spare air filters

Software warranty agreement

Harmonic ships rack-mounting kits in a separate shipping container

33 Installing the Encoder in a Rack You can install the encoder in different sizes and types of racks For rack assembly instructions consult the manual that came with the rack or the customer service department of the rack manufacturer

This section describes how to mount the encoder in a standard 19-inch rack using the two side-mount rails included in the rack-mounting kit A 30-inch-deep rack with a spacer or chimney between racks with multiple encoders is the recommended rack setup However these rails work for racks that are 30 to 36 inches deep

When you view the rack from the rear the power rail should be installed on the left side

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 20: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 15 Ion AVC SD Version 30 Rev K

331 Rack GuidelinesWhen operating the encoder in the rack ensure that

The ambient temperature around the unit (which may be higher than room temperature) is within the limit specified for the unit

There is sufficient airflow around the unit

Electrical circuits are not overloaded consider the nameplate rating of all the connected equipment

There is overcurrent protection

The equipment is properly grounded

No objects are placed on top of the unit

332 Chassis Warnings for Rack Mounting and Servicing

CAUTION To prevent bodily injury when mounting or servicing this unit in a rack you must take special precautions to ensure that the system remains stable The following guidelines are provided to ensure your safety

This unit should be mounted at the bottom of the rack if ilsquot is the only unit in the rack

If the rack will hold a number of units load the rack from the bottom to the top while placing the heaviest component at the bottom of the rack

If the rack is provided with stabilizing devices install the stabilizers before mounting or servicing the unit in the rack

ATTENTION Pour eacuteviter toute blessure corporelle pendant les opeacuterations de montage ou de reacuteparation de cette uniteacute en casier il convient de prendre des preacutecautions speacuteciales afin de maintenir la stabiliteacute du systegraveme Les directives ci-dessous sont destineacutees agrave assurer la protection du personnel

Si cette uniteacute constitue la seule uniteacute monteacutee en casier elle doit ecirctre placeacutee dans le bas

Si cette uniteacute est monteacutee dans un casier partiellement rempli charger le casier de bas en haut en placcedilant lrsquoeacuteleacutement le plus lourd dans le bas

Si le casier est eacutequipeacute de dispositifs stabilisateurs installer les stabilisateurs avant de monter ou de reacuteparer luniteacute en casier

WARNUNG Zur Vermeidung von Koumlrperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell muumlssen sie besondere Vorkehrungen treffen um sicherzustellen daszlig das System stabil bleibt Die folgenden Richtlinien sollen zur Gewaumlhrleistung Ihrer Sicherheit dienen

Wenn diese Einheit die einzige im Gestell ist sollte sie unten im Gestell angebracht werden

Bei Anbringung dieser Einheit in einem zum Teil gefuumlllten Gestell ist das Gestell von unten nach oben zu laden wobei das schwerste Bauteil unten im Gestell anzubringen ist

Wird das Gestell mit Stabilisierungszubehoumlr geliefert sind zuerst die Stabilisatoren zu installieren bevor sie die Einheit im Gestell anbringen oder sie warten

333 Airflow The airflow through the encoder is critical for maintaining the proper temperature range Fans in the chassis draw air in through the front bezel and through the encoder The airflow ventilates out the right side (front view)

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 21: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 3 Installation Installing the Encoder in a Rack

copy 2011 Harmonic Inc 16 Ion AVC SD Version 30 Rev K

CAUTION Do not obstruct the airflow of the encoder Severe equipment damage can result when the encoder cannot properly exhaust the airflow

334 Attaching the Rack Rails Attach the side-mount rack rails to the rack to hold the encoder in place Figure 3-1 illustrates the parts of the rack rails

Figure 3-1 Rack rails

To attach the rack rails to the rack

1 If needed place a Tinnermantrade speed nut with the nut on the outside of the rack over the holes to which you would like to mount the rails

NOTE Each of the four rack posts requires two speed nuts

2 Position the rack rails so the shelves are toward the inside of the rack

3 Using the 10 screws provided with the encoder screw the mounts into the speed nuts from the inside of the rack using the rack-mount holes that line up with the holes on the rack posts

Figure 3-2 illustrates attaching the rails

Figure 3-2 Attaching the rails to the rack

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 22: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 3 Installation Installing Encoder Software

copy 2011 Harmonic Inc 17 Ion AVC SD Version 30 Rev K

CAUTION Make sure to install the rack rails with the shelf at the top of the rail If you install the rail upside down the rail blocks the encoder air vents which can result in overheating the encoder

335 Mounting the EncoderTo mount the encoder in a rack

1 Using both hands grasp the outside corners of the plastic front bezel and slowly pull to detach it from the encoder and expose the mount holes See Figure 3-3

2 Gently slide the encoder to rest on the rack rails

3 Push the encoder back until the rack-mount holes in the front of the encoder line up with the rack posts

4 Insert four screws through the mount holes in the front of the encoder through to the corresponding holes on the rack posts

5 Tighten the screws with a screwdriver

6 Carefully replace the front bezel of the encoder making sure you do not damage the air filters

Rack-mount Holes

Front Bezel

Figure 3-3 Mounting the encoder

34 Installing Encoder SoftwareYour encoder comes from the factory with the latest released software version installed Harmonic periodically releases software updates You can download new software to the encoder using NMX See the NMX online help for instructions for how to download and begin running new encoder software

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 23: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 18 Ion AVC SD Version 30 Rev K

35 Cabling the Encoder CAUTION Do not make any cable connections when the power cord is connected You must unplug the power cable to turn off the encoder

The next sections describe how to connect the following cables

Audio input

Video input

IP output

Ethernet management

Power

351 Back PanelFigure 3-4 shows a sample back panel of the DiviCom Ion AVC SD encoder

AC Power

Fuse CoverFault andLocator LEDs

FaultRelayPort

EthernetManagement Port

EthernetOutput Ports

Plug Video Input Ports

Figure 3-4 Back panel

352 Connecting the Audio Input Cables An encoder may have up to five audio input cards (AICs) each of which has two stereo digital audio ports or up to five audio host cards (AIC) each of which has four stereo digital audio ports

To connect the audio cables

Connect a coaxial cable with a BNC connector from the digital audio port to the audio source On each AIC the digital audio ports are labeled DGTL AUD1 and DGTL AUD2 On each AHC-RAC the digital audio ports are labeled DGTL AUD1 DGTL AUD2 DGTL AUD3 and DGTL AUD4 For multichannel audio use three cables to connect the surround mix connecting LR to DGTL AUD1 CLfe to DGTL AUD2 and LsRs to DGTL AUD3 which maps the channels to AES3 pairs as defined by SMPTE 320M If the encoder is equipped with an AHC-RAC then one more stereo pair can be connected to DGTL AUD4 Otherwise the fourth connector is not used

353 Connecting the Video Input Cables Your encoder has up to four video input ports The video input ports accept serial digital video To connect the video cables

1 Connect a coaxial cable with a BNC connector from the first video source to the Video 1 port on the encoder

2 Continue connecting the additional video sources to the remaining video ports

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 24: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 19 Ion AVC SD Version 30 Rev K

354 Connecting the IP Output Cables The encoder has one IP output port with two redundant channels and two RJ-45 connectors

NOTE The network hosting the IP output traffic must be a different network from your management network and must be configured with a different IP address

NOTE Harmonic recommends that shielded and grounded Ethernet cables be used on all Ethernet ports

To connect the IP output cables

1 Connect an Ethernet cable from the primary IP output port to a port on a network switch or router not a hub

2 Optionally connect the backup IP output port to a different switch or router to facilitate redundancy

3 Configure the Ethernet switch to support autonegotiation by setting each port to ldquoset speed autordquo and ldquoset duplex autordquo

NOTE Failure to properly configure the Ethernet switch could result in a mismatch between the IP output and the switch

Harmonic supports 101001000 Base-T and is fully compliant with IEEE 8023 8023u and 8023as standards

355 Connecting the Ethernet Management Cable The Ethernet management port allows communication between NMX and the encoder

To connect the Ethernet management cable

Connect an RJ-45UTP cable from the encoderrsquos back panel 10100 Base-T port to a port on an Ethernet switch

NOTE The network hosting the IP output traffic should be a different network from your management network

356 Connecting the AC Power The encoder AC power supply uses autosensing to adjust to different incoming voltages

CAUTION This product relies on the buildingrsquos electrical installation for short-circuit (overcurrent) protection Ensure that a fuse or circuit breaker no larger than 120 VAC 20 A US (240 VAC 20 A international) is used on the phase conductors (all current-carrying conductors)

ATTENTION Pour ce qui est de la protection contre les courts-circuits (surtension) ce produit deacutepend de lrsquoinstallation eacutelectrique du local Veacuterifier qursquoun fusible ou qursquoun disjoncteur de 120 V alt 20 A US maximum (240 V alt 20 A international) est utiliseacute sur les conducteurs de phase (conducteurs de charge)

WARNUNG Dieses Produkt ist darauf angewiesen daszlig im Gebaumlude ein Kurzschluszlig-bzw Uumlberstromschutz installiert ist Stellen sie sicher daszlig eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom 20 A (bzw in den USA 120 V Wechselstrom 20 A) an den Phasenleitern (allen stromfuumlhrenden Leitern) verwendet wird

To connect the power cord

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 25: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 3 Installation Cabling the Encoder

copy 2011 Harmonic Inc 20 Ion AVC SD Version 30 Rev K

Connect the power cord to the power plug on the encoder back panel and connect the power cord to the power outlet

CAUTION The power supply cord is used as the main disconnect device Ensure that the socketoutlet is locatedinstalled near the equipment and is easily accessible

ATTENTION Le cordon drsquoalimentation est utiliseacute comme interrupteur geacuteneacuteral La prise de courant doit ecirctre situeacutee ou installeacutee agrave proximiteacute du mateacuteriel et ecirctre facile drsquoacceacutes

WARNUNG Das Netzkabel dient als Netzschalter Stellen sie sicher das die Steckdose einfach zugaumlnglich ist

Power Supply Cord Notice

CAUTION This unit has more than one power supply connectionrsquo all connections must be removed to remove all power from this unit

ATTENTION Cette uniteacute est eacutequipeacutee de plusieurs raccordements dalimentation Pour supprimer tout courant eacutelectrique de luniteacute tous les cordons dalimentation doivent ecirctre deacutebrancheacutes

WARNUNG Diese Einheit verfuumlgt uumlber mehr als einen Stromanschluszlig um Strom gaumlnzlich von der Einheit fernzuhalten muumlssen alle Stromzufuhren abgetrennt sein

Laser warning

Warning Class 1 laser product

Attention Produit laser de classe 1

Warnung Laserprodukt der Klasse 1

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 26: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 21 Ion AVC SD Version 30 Rev K

Chapter 4Operating the Encoder

After installing the encoder in a rack and connecting the cables as described in Chapter 3 Installation configure the encoder platform and services

The chapter describes

How to use NMX Digital Service Manager to configure the Ion AVC SD

How to use the Ion AVC SD front panel

41 Operating with NMX Digital Service ManagerWhen you use NMX Digital Service Manager to manage the encoders in your network you perform all encoder configuration including IP address assignment in NMX You do not need to do any configuration from the encoder front panel

See the NMX online help for instructions for adding an encoder to an NMX network group You will need to know the encoder MAC address when you add the encoder to a network group See 424 Viewing the Encoder MAC Address on page 23 for instructions for viewing the MAC address in the front panel display

42 Using the Front Panel You can perform some initial network configuration from the encoder front panel From the front panel you can set the encoderrsquos IP address default gateway and subnet mask and you can view the encoderrsquos MAC address and serial number

421 The Keypad The keypad on the local control panel provides the following functions

Access to the menus

Navigation through the menu hierarchies to their parameters

Editing capabilities

Figure 4-1 shows the keypad

Hot Keys Navigation andFunction Keys

Alphanumeric Keys

Figure 4-1 Front panel keypad

Seven hot keys provide immediate access to the encoder menus The Network and Help hot keys are currently active The other hot keys are reserved for future use

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 27: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 22 Ion AVC SD Version 30 Rev K

Navigation and function keys located to the right of the hot keys provide a tool for navigating through the menu hierarchies and changing parameter values Use the alphanumeric keys to enter new values

422 Front Panel Display

The two-line 20-character vacuum fluorescent display (VFD) shows the menus parameters and options As illustrated in Figure 4-2 line 1 of the local control panel display shows the menu path for the currently selected option To represent a path the VFD displays each submenu as two or more letters and a colon

Line 2 of the display shows the second line of a help message or a parameter value To change this value you must enter the new value using the keypad

NTWK Control IPParameter Requires

Value to be Edited

Value Setting

19216824101

Figure 4-2 Setting a value in the front panel display

A blinking cursor shows the current value A steady cursor shows the value being edited

Press the Help key to display an online message for the currently selected menu item

423 Setting the Encoder Network PropertiesBefore you can begin to configure the encoder you must set the encoder IP address subnet mask and default gateway The encoder ships with a default IP address based on the encoder serial number The default subnet mask is 255000 and the default gateway address is 10001

4231 Setting the IP Address

To set the encoder management port IP address

1 Press the NTWK hot key

The VFD display shows NTWK Configuration

2 Press the

v key to navigate to NTWK Control IP

3 Press Enter

4 Enter the IP address using the alphanumeric keys

TIP To enter a period press the Shift key and the 0 key

5 When you finish press Enter

Do not exit the Network menu because you can set the other properties from here

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 28: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 4 Operating the Encoder Using the Front Panel

copy 2011 Harmonic Inc 23 Ion AVC SD Version 30 Rev K

4232 Setting the Subnet Mask

To set the subnet mask

1 Press the

v key to navigate to NTWK Control Subnet

2 Press Enter

3 Enter the subnet mask using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

4233 Setting the Default Gateway Address

To set the gateway address

1 Press the

v

key to navigate to NTWK Gateway

2 Press Enter

3 Enter the default gateway using the alphanumeric keys

TIP To enter a period press the Shift key and press the 0 key

4 When you finish press Enter

5 Press Esc to exit the Network menu

424 Viewing the Encoder MAC Address You can view the encoder MAC address from the front panel

To view the encoder MAC address

1 Press the NTWK hot key

2 Press the

v

key several times to navigate to NTWK Control MAC

The MAC address appears beneath the parameter name

3 Press Esc to exit the parameter

425 Viewing the Encoder Serial NumberYou can view the encoder serial number from the front panel

To view the encoder serial number

1 Press the STAT hot key

2 Press the

v

key to navigate to STAT Serial Number

The serial number appears beneath the parameter name

3 Press Esc to exit the parameter

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 29: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 4 Operating the Encoder Licensing Information

copy 2011 Harmonic Inc 24 Ion AVC SD Version 30 Rev K

43 Licensing InformationLicensing is required for some encoding features and you cannot enable those features without the appropriate licensing You can add licenses to your system at any time using the Configuration Manager (Web GUI) You must acquire licenses from Harmonic When licenses expire streams will continue to flow as configured but cannot be modified or re-enabled if disabled for any reason Streams that include features under license will raise alarms when their licensing expires Alarms will also be raised to advise you that licensing is required for a given feature if that feature is blocked Also any attempted changes after a license expires may be service affecting and other operations such as redundancy may not operate properly For additional information on using the Configuration Manager for licensing operations refer to your encoderrsquos online help

Under the Licensing tab (on Platform Configuration page) you can

Apply license keys that have been created and sent to you by Harmonic in a lic license file The license file is unique to a specific encoder and can be used on that encoder only once When you apply a license the system scans the encoder platform for the matching devicefeature and binds the license key to that encoder One lic file may contain multiple license keys Every key in the lic file will be applied One license key may unlock multiple instances of a feature There is no undo for applying licenses but you can delete them

Delete a license key and save the deletion receipt for return to Harmonic If you want to remove a license key from one device to use it on another you must delete it When you delete a key the device releases it and a unique deletion receipt is created This receipt must be sent to Harmonic so that the deleted license can be made available in the license database for use in a different encoder There is no undo for deletion You must provide the deletion receipt to Harmonic to make the license available for use again

View the current licenses that are on the encoder platform

To apply licenses

If you ordered a new license you received a file To install it on this encoder follow these steps

1 Click the Add license button The license Loader window opens

2 Type in the path and file name where you saved the new license file or use the Browse button and navigate to it

3 Click the Transfer button The encoder applies all the license keys that are in the lic file and binds them to the encoder The new licenses appear in the license table

4 Disable then re-enable the affected streams if applicable

To delete licenses

Contact Harmonic customer support for more information

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 30: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 25 Ion AVC SD Version 30 Rev K

Chapter 5Maintenance and Troubleshooting

This chapter describes

How to maintain and replace the air filters and fuse

How to contact Harmonic Support

51 Air Filters The encoder uses two air filters to minimize dust and dirt in the circuitry and components in the chassis These filters are made of flexible compressed fiber spun from urethane foam Installed in the front of the encoder the filters are fire retardant and conform to UL 900 Class II specifications

The bezel filter is located inside the front bezel on the left side Figure 5-1 shows the dimensions of the bezel filter The notches on the left side and the cutouts in the middle can fit on either side of the front bezel mounting posts

532 inches

164 025 inchesinches

Figure 5-1 Bezel filter (front view)

The keypad filter is located behind the front panel keypad Figure 5-2 shows the keypad filter

645 inches

025 inches

164inches

Figure 5-2 Keypad filter (front view)

511 Maintaining the Air Filters The operating environment of the encoder plays a large factor in determining the life of the air filters Encoders that operate in dusty and dirty surroundings require more frequent inspections and filter cleaning than those operating in cleaner environments

Inspect and clean the filters with a frequency that is appropriate to the environment in which the encoder operates Harmonic recommends inspecting and cleaning the filters every six weeks to ensure proper airflow through the chassis

To clean dust and dirt from the filters you can use a vacuum cleaner to remove the dirt or you can rinse the filters in water You can also use soaps or mild detergents on the filters If you rinse the filters in water make sure that you squeeze the excess water from them before reinstalling them in the encoder You might need to order replacement filters if the filters become too dirty over time

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 31: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 5 Maintenance and Troubleshooting Fuse

copy 2011 Harmonic Inc 26 Ion AVC SD Version 30 Rev K

512 Removing and Replacing the Air Filters You do not need to turn off the encoder when removing and replacing the air filters

5121 Removing and Replacing the Bezel Filter

To remove the front left filter from behind the front bezel

1 Grasp each side of the encoderrsquos front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

3 Remove the filter from inside the front bezel

4 Inspect the air filter for dirt and clean it if necessary

NOTE When the filter is new its color is medium charcoal As dust and dirt collect in the porous filter material the filterrsquos color gradually changes to brown then an ash color

5 Replace the filter inside the front bezel Place the filter so that the long horizontal slot is at the bottom edge Carefully place the cutouts in the filter around the bezel mounting posts

6 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

5122 Removing and Replacing the Keypad Filter

To remove the air filter from behind the keypad

1 Grasp each side of the encoder front bezel with your hands

2 Carefully remove the front bezel by pulling it away from the encoder

Note the location of the filter The keypad is screwed onto the front of the encoder through four mounting posts Cutouts on the filter wrap around the four posts and the right side of the filter extends past the keyboard

3 Remove the filter by pulling the left side of the filter up and away from the keyboard mounting posts then pulling up the right side

4 Inspect the air filter for dirt and clean it if necessary

5 Replace the filter by inserting the right side of the filter behind the keypad with the vertical slots around the mounting posts

6 Insert the left side of the filter placing the horizontal cutouts around the mounting posts

7 Carefully replace the front bezel on the encoder making sure the filter does not fall out of the bezel

52 Fuse Encoders use a slow blow 40 A 250 V fuse 5 x 20 mm The fuse is located on the back panel beside the power input A spare fuse is located in the fuse cover shown in Figure 5-3

Fuse cover

Figure 5-3 Fuse cover and AC power input

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 32: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Chapter 5 Maintenance and Troubleshooting Contacting Harmonic Support

copy 2011 Harmonic Inc 27 Ion AVC SD Version 30 Rev K

521 Replacing the FuseTo replace the fuse

1 Unplug the power cord from the chassis

DANGER You must disconnect the power cord before removing the fuse

2 Pull down the fuse cover on the back panel

3 Remove the old fuse

4 Install the new fuse

DANGER Always replace the fuse with a fuse of the same rating and type Using a different fuse voids the Harmonic warranty and could result in fire or other electrical damage

5 Replace the fuse cover

6 Plug in the encoder

53 Contacting Harmonic SupportThe Harmonic Customer and Technical Support groups are available to help you with any questions or problems you may have regarding Harmonic products

For assistance from within the US and Canada call toll free

1888MPEGTWO (6734896)

For assistance from outside the US and Canada call

14084906477

The fax number is 4084906770

The email address is techhelpharmonicinccom

The corporate address for Harmonic Inc is

Harmonic Inc 4300 North First Street San Jose CA 95134 USA Attn Customer Support

The corporate telephone numbers for Harmonic Inc are

Tel 18007881330 (from the US and Canada) Tel +14085422500 (outside the US and Canada) Fax+14084906708

The Web address for Harmonic Inc is wwwharmonicinccom

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 33: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 28 Ion AVC SD Version 30 Rev K

Appendix AAudio and Video Specifications

A1 AIC FeaturesThe AIC adapter accepts analog (balanced or unbalanced) discrete AES3SPDIF digital and AES3 embedded in serial digital video inputs For analog and discrete AES3 inputs sampling frequencies of 48 kHz 441 kHz and 32 kHz are supported Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video

Table A-1 lists the AIC features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-1 AIC Features

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

MPEG-1 Layer II compression

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz 441 kHz 48 kHz

64 96 112 128 160 192 224 256 320 384

MPEG-1 Layer II compression SPPC (separate PID per channel)

Single channel (10) 32 kHz 441 kHz 48 kHz

32 48 56 64 80 96 112 128 160 192

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a 512a 576a

640a

Stereo channel (20) 32 kHz 441 kHz 48 kHz

96 112 128 160 192

224 256 320 384 448a

512a 576a 640a

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

32 kHz441 kHz48 kHz

56b 80b 96 112 128 160 192 224 256 320 384

448a 512a 576a 640a

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448a 512a

576a 640a

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 34: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 29 Ion AVC SD Version 30 Rev K

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A2 On-board Audio Encoding FeaturesEmbedded digital audio is carried in the serial digital video input Embedded digital is supported only for 48 kHz sampling which must be synchronous to the video The on-board audio encoder can encode up to three stereo pairs Only one audio compression format can be selected for the stereo pairs at any time

MPEG HE AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

32 48 56 64 96 112 128

MPEG AAC compression

Single channel (10) 32 kHz441 kHz48 kHz

32 48 56 64 96 112 128 182 192

Dual channel (1+1) Stereo channel (20) Joint stereo channel

32 kHz441 kHz48 kHz

64 96 112 128 182 192 224 256 320 384

a These rates are not compliant with A53b These rates are valid for 10 coding only

Table A-1 AIC Features continued

AIC Feature Coding Mode SamplingFrequency

ES Bit RatesSupported (Kbps)

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 35: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix A Audio and Video Specifications On-board Audio Encoding Features

copy 2011 Harmonic Inc 30 Ion AVC SD Version 30 Rev K

Table A-2 lists the on-board audio features for each coding mode including the supported sampling frequencies and ES bit rates

Table A-2 Onboard Audio Features

Onboard Audio Feature Coding Mode Sampling

FrequencyES Bit Rates

Supported (Kbps)

MPEG-1Layer II compression

48 kHz 64 96 112 128 160 192 224 256 320 384

Dolby Digital (AC-3) compression

Single channel (10) 32 kHz 441 kHz 48 kHz

56 64 80 96 112 128 160 192 224 256 320

384 448a

a These rates are not compliant with A53

512a 576a

640a

Stereo channel (20) 48 kHz 96 112 128 160 192 224 256 320 384 448 512 576 640

Dolby Digital (AC-3) passthrough

Up to 51 channels (32+LFE professional 16-bit mode)

48 kHz 32 kHz 441 kHz

56 80 96 112 128 160 192 224 256 320 384

448 512 576 640

Up to 51 channels (32+LFE professional 32-bit mode)

32 kHz441 kHz48 kHz

256 320 384 448 512 576 640

MPEG HE AAC compression

48 kHz 32 48 56 64 96

48 kHz 32 48 56 64 96 112 128

MPEG AAC compression

48 kHz 32 48 56 64 96 112 128 182 192

48 kHz 64 96 112 128 182 192 224 256 320 384

Note the following limitations

ATSC Standard A53 specifies that only 48 kHz sampling may be used and that ES bit rates must be less than or equal to 384 Kbps for a complete service It also specifies that a two-channel dialog-only service must be less than or equal to 192 Kbps Total ES rates for all services must be less than or equal to 512 Kbps

Embedded audio must be 48 kHz sampling and synchronous with the video See SMPTE 272M for definitions

MPEG AAC and HE AAC can be placed into the output Transport Stream encapsulated in either of two methods

ADTS

ADTS is an acronym for ldquoAudio Data Transport Streamrdquo This is the default used if the user selects MPEG-2 AACHE AAC ADTS is assigned a stream type value of 0x0F

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Single channel (10)

Dual channel (1+1) Stereo channel (20) Joint stereo channel

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 36: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix A Audio and Video Specifications MPEG-1Layer II Audio

copy 2011 Harmonic Inc 31 Ion AVC SD Version 30 Rev K

LATMLOAS

LATM is an acronym for rdquoLow Overhead Audio Transport Multiplexrdquo LOAS is an acronym for rdquoLow Overhead Audio Streamrdquo and furnishes an outer wrapper for LATMs inner wrapper of the raw audio Elementary Stream syntax MPEG-4 AAC and HE AAC bitstreams are encapsulated as LATMLOAS and assigned a stream type value of 0x11

Encapsulation mode is controlled by selecting rdquoMPEG-2rdquo or rdquoMPEG-4rdquo as required

A21 PCM Downmix from 51 This encoder has the ability to accept 51 PCM (three pairs embedded on AES or embedded) and create a downmix before 20 encoding Audio encoding is accomplished Onboard RAC or an AHC-561adapter Refer to the NMX online help for additional information

A22 Re-encode AbilityThis encoder has the ability to passthrough two additional audio streams aong with one reencode stream However you cannot mix encode streams with re-encode streams Refer to the NMX online help for additional information

A3 MPEG-1Layer II AudioTable A-3 lists the bit rates in Kbps for the sample frequencies of 48 kHz This table is for MPEG-1 Layer II audio

Table A-3 MPEG-1Layer II Audio Bit Rates

Audio Bit Rate (Kbps)Audio without PCR Audio with PCR

48 kHz 48 kHz

32 418 418

48 522 522

56 627 627

64 731 731

80 836 940

96 1044 1044

112 1253 1253

128 1358 1358

160 1671 1671

192 1984 2089

224 2298 2402

256 2716 2716

320 3342 3342

384 3969 3969

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 37: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix A Audio and Video Specifications Dolby Digital (AC-3) Audio

copy 2011 Harmonic Inc 32 Ion AVC SD Version 30 Rev K

A4 Dolby Digital (AC-3) Audio The Ion AVC SD supports supports native two-channel Dolby Digital (AC-3) compression AIC equpped encoders support native two-channel Dolby Digital (AC-3) compression

NOTE Harmonic supports Dolby Digital (AC-3) passthrough rates of 96 to 640 Kbps and native Dolby Digital (AC-3) rates of 56 to 640 Kbps

Table A-4 lists the bit rates for the sample frequencies of 48 kHz 441 kHz and 32 kHz

Table A-4 Dolby Digital (AC-3) Audio Bit Rates

Audio Bit Rate (Kbps)

Audio without PCR Audio with PCR

48 kHz 441 kHz 32 kHz 48 kHz 441 kHz 32 kHz

56 658 605 627 658 605 627

64 752 691 689 752 691 689

80 846 864 877 846 864 877

96 1034 1036 1003 1034 1036 1065

112 1222 1209 1191 1222 1209 1191

128 1316 1382 1316 1410 1382 1379

160 1692 1641 1692 1692 1727 1692

192 1974 1986 2005 2068 1986 2005

224 2350 2332 2319 2350 2332 2319

256 2632 2677 2632 2726 2677 2695

320 3290 3282 3321 3384 3368 3321

384 3948 3973 3948 4042 3973 3948

448 4606 4664 4637 4606 4664 4637

512 5264 5268 5264 5264 5268 5264

576 5922 5959 5891 5922 5959 5953

640 6580 6564 6580 6580 6564 6580

NOTE Changing from non-single-channel mode to single-channel mode provisions the transport bit rate automatically

When you change between single-channel and non-single-channel modes the encoder automatically provisions the bit rate to the closest available bit rate In some cases this means the bit rate is lower because provisioning does not increase the bit rate defined for the port Therefore changing the coding mode from non-single-channel mode to any of the four highest bit rates causes the encoder to provision the bit rate to 192 Kbps

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 38: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix A Audio and Video Specifications Video Specifications

copy 2011 Harmonic Inc 33 Ion AVC SD Version 30 Rev K

In the case of the three lowest bit rates when you change from single-channel to non-single-channel mode because the bit rate is the lowest available the encoder provisions to the next highest available bit rate 64 Kbps If you set the bit rate to 80 Kbps and then change the coding mode to non-single-channel the encoder provisions the bit rate to 64 Kbps

A5 Video Specifications The encoder is equipped to handle standard definition (SD) serial digital input (SDI)

Table 5-1 Video Specifications

Feature Specification Comments

Input formats Serial digital component Standard definition serial digital interface (SD-SDI) per SMPTE 259M

SNR gt52 dB rms Unweighted

Frequency response gt ndash03 dBgt ndash05 dB

42 MHz55 MHz

Differential gain lt +ndash15 10 to 90 APL

Differential phase lt +ndash15 10 to 90 APL

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 39: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 34 Ion AVC SD Version 30 Rev K

Appendix BEncoder Specifications

This appendix contains a comprehensive list of the environment and physical characteristics of the encoder electrical specifications and information about the pinouts for the input and output ports

B1 Environment Specifications Table B-1 lists environment specifications for the encoder

Table B-1 Environment Specifications

Parameter Specification

Size 445 cm x 4826 cm x 6069 cm (175 in x 19 in x 24 in)

Weight 11 kg (24 lb)

AC Power

AC 100-240V (auto ranging)

47 to 63 Hz

Ion-4-AVC 180 W (18 A)

63A 250V fuse 5x20mm

Temperature

0 to 40 degC (32 to 104 degF)

ndash20 to +80 degC (ndash4 to +176 degF)

Humidity

lt 95 noncondensing

lt 95 noncondensing

Altitude

lt 15000 feet (4572 meters)

lt 40000 feet (12192 meters)

Shock and Vibration

Passes the impact compression and vibration requirements of ASTM D4169-94 Distribution Cycle 13 Assurance Level 1

Passes NEBS Office Vibration Test while operating (01G sine sweep 5 to 100 Hz 3 axis)

Input voltage range

Line frequency

Typical consumption

Fuse

Operating

Storage

Operating

Storage

Operating

Storage

Packaged

Operating

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 40: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix B Encoder Specifications Port Specifications

copy 2011 Harmonic Inc 35 Ion AVC SD Version 30 Rev K

B2 Port Specifications Table B-2 lists the specifications for the back panel port connections For port locations see the illustration of the back panel on Figure 3-4 on page 18

Table B-2 Port Specifications

Port Connection Specification

Video input port

Serial Digital

75 Ω unbalanced

BNC

Ethernet management port

10100 Base-T

8023

RJ-45

Input serial port Reserved for future use

Ethernet output port

101001000 Base-T

MPEG-4 over IP

RJ-45

Fault relay port Capable of switching 025 amps at 30 VDC

Phoenix 1881383

B3 Port Pinouts The following sections describe the Ethernet management and fault relay port pinouts

B31 Ethernet Management Port The Ethernet management port is 10100 Base-T and uses an RJ-45UTP port to connect to an Ethernet network Use this port to manage the encoder with NMX See 355 Connecting the Ethernet Management Cable on page 19 for cabling instructions

Table B-3 lists the pinouts for the RJ-45 Ethernet port

Protocol Signal format per SMPTE 259M Data stream format per ITUR BT 601

Impedance

Connector type

Type

Protocol

Connector type

Type

Protocol

Connector type

Mating connector type

Table B-3 Ethernet Management Port Pinout

Pin Signal

1 Transmit data (TD) +

2 Transmit data (TD) ndash

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 41: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 36 Ion AVC SD Version 30 Rev K

3 Receive data (RD) +

4 Not connected

5 Not connected

6 Receive data (RD) ndash

7 Not connected

8 Not connected

Table B-3 Ethernet Management Port Pinoutcontinued

Pin Signal

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 42: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix B Encoder Specifications Port Pinouts

copy 2011 Harmonic Inc 37 Ion AVC SD Version 30 Rev K

B32 Fault RelayGPI Ports A contact closure is a physical connection between two platforms that define the state of the platform by being either on or off

Both NMX and SAG provide alarm management and redundancy for third party devices through contact closure monitoring Additionaly the contact closure on the Electra and Ion-based encoders can also be used as DPI inputs to the encoder A contact closure is a physical connection (Figure B-1) between two platforms that define the state of the platform by being either on or off Table B-4 lists the fault relay pinouts Individual wires need to be inserted into the contacts and grounded to the ground pin to activate a contact closure When configured in the DPI properties page (of either NMX or SAG) an SCTE35 message is sent out when that pin is set to low Each is independent and can be provisioned to any one channel and multiple available channels

The fault relay port connects to a Form C relay that can switch up to 025 A at 30 VDC

Table B-4 Fault RelayGPI Port Pinout

Pin Connection

1 Normally closed (NC)

2 Normally open (NO)

3 Common (CM)

4 GPI contact 1

5 GPI contact 2

6 GPI contact 3

7 GPI contact 4

8 Ground (GND)

Figure B-1 Fault RelayGPI Ports

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 43: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 38 Ion AVC SD Version 30 Rev K

Appendix CEncoder Back Panel Slot Locations

C1 Adapter Configurations for All EncodersFigure C-1 represents the back panel of an encoder Table C-1 shows the slot number and the adaptersmodules that can be installed in encoders that are not associated with a FLEX module Table C-2 shows the slot number and the modules associated with the FLEX module that can be installed NMX uses the slot number to differentiate between adapters of the same type within the encoder

Slot 3 Slot 4 Slot 5 Video Ports

Slot 1 Slot 2 Slot 255

Figure C-1 Slot numbers

Table C-1 shows the adaptersmodules software support and configuration recommendations for non-FLEX based encoders

Table C-1 Supported adaptersmodules and configuration recommendations for this encoder

Card Slot Notes

AIC Any slot (1-5 cards per chassis)

AHC-RAC Any slot (1-5 cards per chassis)

AHC-561 Any slots 1-4 (1-4 cards per chassis) Not supported on slot 5 Supported only via NMX

ASI Output Slot 5 without a FLEX module Slot 2 with a FLEX module (1 card per chassis)

Only the first two ports are active and are electrical duplicates of each other

AB Power Switch Input Adapter

Slots 1 and 3 (both)

C11 Additional Card Configurations for FLEX-based EncodersTable C-2 lists the card configurations available for FLEX-based encoders

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

FLEX Slot 4 must be populated first slot 5 second (1-2 adapters per chassis)

Requires CPC revision 105 or higher see Viewing the Control Board (CPC) Revision Information on page 39

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 44: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix C Encoder Back Panel Slot Locations Adapter Configurations for All Encoders

copy 2011 Harmonic Inc 39 Ion AVC SD Version 30 Rev K

NOTE ASI Input modules (used with FLEX module) and ASI Output modules utilize the same hardware but perform different functions based on 1) the slot number and 2) if a FLEX module is installed If installed in slots 2 or 5 the ASI module is always an output If a FLEX module is installed an ASI module installed in slots 1 or 3 is an input

C12 Viewing the Control Board (CPC) Revision Information1 From the Platform tab click on the Platform link

2 Click on the Control Board (CPC) link

The Control Board (CPC) Configuration page appears

3 Click on the Maintenance tab to examine the version information

GbE Slot 1 only (1 adapter per chassis)

Used with FLEX module for input only

ASI Input Slot 1 (typical) slot 3 if slot 1 isalready in use (1 card perchassis) For FLEX only chassisthe FLEX module goes into slot4 and 5 Slot 4 must bepopulated first For baseband andcompressed mixed inputencoders the FLEX module canbe either slot 4 or 5 ASI inputadapters cannot use slot 4 as itis used for first FLEX module

ASI input is currently only for FLEX module ASI in slots 1 3and 4 appears as an input card

RF 8VSB Slot 1 (typical) or slot 3 if slot 1 is already in use or slot 2 if slots 1 and 3 are already in use (1 adapter per chassis)

Used with FLEX module for input only

Table C-2 FLEX Module Options (for use with FLEX module)

Card Option Notes

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 45: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 40 Ion AVC SD Version 30 Rev K

Appendix DBoot Sequence

This appendix describes the encoder boot sequence including the messages that appear on the local control panel display

D1 Local Control Panel Display Messages during BootupMessages on the local control panel indicate progress during boot-up During a successful boot many events occur so quickly you cannot see the messages The following sections describe the messages that you can see during boot attempts

NOTE During the boot sequence do not press any key on the keypad

The following sequence describes the display on the vacuum fluorescent display (VFD) during a successful startup

Power on

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D2 Other Local Control Panel Display MessagesThe local control panel displays messages for other types of restarts including a system reset and loading new software

D21 Resetting the Encoder When you reset the encoder from NMX a message on the VFD shows that the encoder has been reset The encoder uses the boot file on the hard drive when you reset it

Reset from NMX

VFD line 1 = Bye bye VFD line 2 =

After power cycle

VFD line 1 = Harmonic Inc VFD line 2 = System Loading

Begin loading

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 46: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix D Boot Sequence Other Local Control Panel Display Messages

copy 2011 Harmonic Inc 41 Ion AVC SD Version 30 Rev K

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

D22 Loading New Software You can download new software to an encoder using NMX After downloading the software restart the encoder to begin using the new software The following messages appear

Begin loading

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = System Loading

Booting

VFD line 1 =DiviCom Ion AVC SD VFD line 2 = Loading xxxxxxxxelf

Finished

VFD line 1 = DiviCom Ion AVC SD VFD line 2 = Multichannel Encoder

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 47: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 42 Ion AVC SD Version 30 Rev K

Appendix EWiring the ndash48 VDC Power Supply

If your encoder has the optional ndash48 VDC power supply follow these steps to wire the power supply

E1 Getting StartedBefore you begin wiring the ndash48 VDC power supply make sure that you provide the necessary overcurrent protection wires and power connector

E2 Power Source SpecificationsThe DC power source feeding the encoder must meet the following requirements

Electrically isolated from any AC power source

Positive ground The Positive bus of the DC power source must be reliably connected to the Ground bus

Each feed-pair must provide a continuous supply of power that meets the following specifications

Table E-1 Power Source Specifications

Parameter Specification

Voltage 40ndash60 VDC

Max operating current 8 amps

Max input surge current

20 amps

E3 Overcurrent ProtectionTo provide overcurrent protection

Provide overcurrent protection devices as part of each rack housing encoders

Locate a readily accessible disconnect device between the DC power source and the encoder

Use a 10-amp double-pole fast trip DC-rated disconnect device for each DC power connector

NOTE Overcurrent protection devices must meet applicable national and local electrical safety codes and be approved for the intended application

E4 Wiring RequirementsThe encoder is connected to the DC power source using three wires

ndashVin

GND

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 48: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix E Wiring the ndash48 VDC Power Supply Power Connector

copy 2011 Harmonic Inc 43 Ion AVC SD Version 30 Rev K

+Vin

Although Harmonic provides the power input connector with the encoder you must supply the wires

The wires to be used must comply with the following specifications

Table E-2 Recommended Wire Specifications

Parameter Specification

Suitable conductor material Copper only

ndashVin and +Vin wires 16 AWG rating

Ground cable 16 AWG rating

Cable insulation rating Minimum 80 C low smoke fume (LSF) flame retardant

Cable type Must comply with at least one of the following standards

Branch circuit cable insulation color

Per applicable national electrical codes

E5 Power ConnectorThe encoder is supplied with a special DC power connector plug that matches the DC power socket on the back of the encoder

This connector is made by WAGO model number 231-103037-000

Use only the original connector for connecting the encoder to the DC power source Contact Harmonic Technical Support if you want to use any other type of connector

The following figure shows the connector and its strain relief housing

Figure E-1 CableStrain Relief Housing

E6 Assembling the DC Input Power CableTo assemble the DC input power cable

1 Prepare the power wires as specified in E4 Wiring Requirements on page 42

2 Use the disconnect device to make sure that the power supply from the DC power source to the cables is switched off

UL 1581 (VW-1) - UL style 1028 or equivalent EEE 383 EEE 1202-1991

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 49: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix E Wiring the ndash48 VDC Power Supply Assembling the DC Input Power Cable

copy 2011 Harmonic Inc 44 Ion AVC SD Version 30 Rev K

CAUTION Turn off the power before proceeding with these instructions

3 Unplug the WAGO power connector from the power socket on the encoder back panel

4 Identify the three wires coming from the DC power source that are used in the connection to the expansion unit

ndashVin

+Vin

GND

5 Strip up to 03 inches (8 mm) of insulation from each of the wires coming from the DC power source

Do not strip more than this length from each wire Stripping more leaves uninsulated wire exposed outside the DC connector after the assembly is complete

6 Insert a small screwdriver into the rectangular hole directly above the hole in the DC connector where you want to insert the first cable and press down on the screwdriver

This opens the cage clamp for this section of the DC plug connector

NOTE WAGO also sells tools specifically designed to open cage clamps easily For more information either visit the WAGO web site at wwwwagocom or call WAGO at 1-800-346-7245 and request information about items 210-250 or 231-131

7 Feed the exposed section of the wire into the matching hole in the DC plug connector

See the pin-out figure below to match wires with the required holes

Figure E-2 Pin Out Specification

8 Repeat steps 5 through 7 for the other two wires to complete the assembly of the DC input cable

NOTE If you need to remove a wire from the DC plug connector insert a small screwdriver into the slot directly above the wire and press down on the screwdriver to free the wire from the cage clamp

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 50: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 45 Ion AVC SD Version 30 Rev K

Appendix FDiviComtrade FLEX Decoding Module

F1 IntroductionThe DiviCom FLEX decoding module delivers video decoding capability and is integrated into either an Electra or Ion encoder chassis (which will be referred to as the ldquohostrdquo encoder) The FLEX decoding module (hereafter referred to as the FLEX module) is a decoding module only (see Figure F-1) A single FLEX module is able to decode up to two (2) incoming channels and an appropriately configured encoder can deliver up to four (4) channels in a single rack-unit (1-RU) The FLEX module decodes MPEG-2 in both standard definition (SD) or high definition (HD) formats thereby eliminating the dependency on ingress formats The FLEX module is a unique gateway designed with the flexibility to deliver any type of pre-compressed video to any host encoder The FLEX module supports both ASI and IP inputs the most efficient interfaces used to route and transport pre-compressed video feeds

NOTE AHC-561 card is not supported for use with FLEX modules

The FLEX module is controlled and configured with the NMX Digital Service Manager application or SAG the Web-based GUI The FLEX module also accepts decoded ATSC 8VSB signals from the DiviCom RF Input Card ( DiviComtrade RF Input Adapter on page 74) The FLEX module does not descramble or reconstruct all audio and ancillary data services (such as VBI) on the output port

NOTE The encoder chassis configuration must include an input module for IP The same GbE Pro card are used for both ProStream 1000 muxes and Electra encoders

Figure F-1 FLEX Module Ports

F2 Video Decoding Specifications Table F-1 describes video specifications supported by the FLEX module See the following tables for more information about video and audio compression

Table F-1 Video Decoding Features

Feature Support

Video Decoding MPEG-2 MPML MPEG-2 MPHL

Aspect Ratios 43 and 169

Video Formats 480i2997 576i25 720p5994 72050 1080i25 1080i2997

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 51: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix F DiviComtrade FLEX Decoding Module Audio Passthrough Specifications

copy 2011 Harmonic Inc 46 Ion AVC SD Version 30 Rev K

F3 Audio Passthrough SpecificationsTable F-2 describes the audio passthrough specifications FLEX module

Table F-2 Audio Passthrough Specifications

Feature Support

Number of channels

Audio formats

Audio processing

Operating modes

Additional features (available on some specific hosts only)

General HD decode and downcovert to SDSD hosts only Decodes MPEG-2 MPML (480i and 576i)HD hosts only Decodes MPEG-2 MPHL (720p 5060 and 1080i

5060)Specific hosts only ASI input and output available with FLEX module (using

two ASI cards) Mixed TS and SDI inputs on encoders with FLEX

modules

8 (however the total passthrough bitrate per FLEX program cannot exceed 4Mbps)

MPEG-1Layer II Dolby Digital (AC-3) and AAC audio passthrough

MPEG-1 Layer II 10 and 20 decode Dolby AC-3 51 and 20 decode

Audio passthrough Audio passthrough of dual channel No Fixed Audio Gain Adjustment for passthrough audio Audio passthrough with repacketization Audio passthrough Silence insertion during CRC errors or buffer underruns

Mono dual channel or decode to stereo joint stereo 51 multichannel (no decode to PCM on audio passthrough)

Table F-1 Video Decoding Features

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 52: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 47 Ion AVC SD Version 30 Rev K

F4 Audio Decode SpecificationsTable 5-2 describes the audio decode specifications FLEX module

Table 5-2 FLEX Audio Decode Specifications

Feature Support

Audio Decoding

Decoding Mode

Audio Formats (MPEG-1Layer II AC-3)

Compression Mode

Additional Support

NOTE Audio leveling is also supported by the FLEX decoding module This feature defines a constant gain adjustment for incoming audio signal

F41 Decoding Resource ConsiderationsA multichannel decode stream counts as 3 stereo decode streams If no downmixing and no dynamic level adjustment is enabled on any stream the absolute maximum number of audio decode streams is 8 allowed in one of these (and only these) combinations

Up to 4 monostereo decode streams per FLEX decoding port

Up to one multichannel audio decode and one stereo decode stream per FLEX decoding port

Up to 2 multichannel audio decode and 2 stereo audio decode streams on the first FLEX decoding port

Up to 8 monostereo decode streams on the first FLEX decoding port (with no audio on second port)

See Table F-3 on page 48 for information on AC-3 resource considerations

Static Level Adjustment Dynamic Level Adjustment

Dolby AC-3 with multichannel decoding and downmixing

Dolby AC-3 Mono and Stereo decoding

Mono and stereo (20)

(AC-3) Line mode and RF line mode

Support for multiple decode of the same PID (audio decode)

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 53: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Table F-3 AC-3 Resource Considerations

Input Format Audio Input (into card) Decoding Mode

Multichannel DownMix checkbox

Result

Resource Usage

Equivalent

AC-3

Mono

Mono Available Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

3 x Stereo

Multichannel No Audio on the Center channel Silence on all others

3 x Stereo

Stereo

Mon Available (irrelevant for this decoding mode)

Audio on the left channel Silence on the right channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

AC-3 (continued)

Multichannel

Mono Available (must be enabled for this decoding mode or an alarm is raised and decoding stops)

Multichannel downmix to Mono on the left channel

Stereoa

Stereo Audio on both channels

Multichannel No Audio on both left and right channels Silence on all others

3 x Stereo

Appendix F DiviComtrade FLEX Decoding Module Audio Decode Specifications

copy 2011 Harmonic Inc 48 Ion AVC SD Version 30 Rev K

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 54: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix F DiviComtrade FLEX Decoding Module Ancillary Data Specifications

copy 2011 Harmonic Inc 49 Ion AVC SD Version 30 Rev K

See Table F-4 on page 49 for information on MPEG-L2 resource considerations

Table F-4 MPEG-L2 Resource Considerations

Input Format Audio Input (into card)

Decoding Mode Result Resource Usage

Equivalent

MPEG-L2

Mono Mono Audio on left channel Silence on right channel StereoStereo

Stereo Mono Audio on both channels

Stereo

F5 Ancillary Data SpecificationsA multichannel encoder equipped with FLEX is essentially receiving and outputting compressed streams Therefore the terminology used regarding ancillary data can be incorrect or misleading VBI data is not applicable to fully digital signals but is used by user habit The FLEX module does not re-create any of the ancillary data it simply passes it intact as packets of bits to the associate encoderrsquos TS output

Table F-5 describes the ancillary data specifications supported by the FLEX module

Table F-5 Ancillary Data Specifications

Feature Support

Vertical Interval Data Services (Pass through only)

WST (Teletext) Inverted WST WSS VPS AFD and bar data VITC Closed Captioning per CEA-608 and 708 AMOL and TV Guide data

Number of channels 4

F6 Input SpecificationsTable F-6 describes the input specifications FLEX module

a Enabling Multichannel downmixing allocates resources for downmixing resulting in resource usage equivalent to 3 x Stereo

Table F-6 Input Specifications

Feature Support

Transport stream Inputs MPEG-2 TS

ASI interface (optional module)

Connector 4x BNC 75 Ω

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 55: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix F DiviComtrade FLEX Decoding Module Output Specifications

copy 2011 Harmonic Inc 50 Ion AVC SD Version 30 Rev K

F7 Output SpecificationsTable F-7 describes the output specifications FLEX module

Table F-7 Outputs Specifications

Feature Support

Video Outputs

Connector Type

Embedded Data along the Video

MPEG format 188 Bytes per TS packet

Processing 1 MPTSSPTS per port Up to 150 Mbps per port

ASI Ports 4

IP interface (optional module)

Type Gigabit Ethernet

IP ports 2 Independent ports

Connector 2 x copper SFPs

Speed 1 x 1000 Mbps per port

IP encapsulation MPEG-2 TS over UDPIP 1 to 7 TS IP

MPEG format 188 Bytes per TS packet

MPEG-2 TS MPTS and SPTS

Maximum Bit-Rate per Socket

80 Mbps

Addressing Unicast and multicast

Management IGMP ARP and ICMP

Forward Error Correction (FEC)

The FLEX module supports SMTE 2022 Annex C forward error correction (FEC) FEC provides lost packet recovery at the receiving devices

RF Input Card

For specifics see Appendix G on page 74

One (1) per decoded channel with video only SDI or HD-SDI One (1) additional per channel for confidence monitoring only

DIN 1023 (DIN 1023 to BNC adapters available)

No Audio VBI VANC or HANC data embedded The data are embedded into the SDIHD-SDI output

Table F-6 Input Specifications

Feature Support

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 56: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix F DiviComtrade FLEX Decoding Module Environmental and Physical

copy 2011 Harmonic Inc 51 Ion AVC SD Version 30 Rev K

F8 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

F9 Module SlotsThe diagram below represents the back panel of typical encoder The diagram shows the slot number and the modules that can be installed in that slot NMX or SAG uses the slot number to differentiate between cards of the same type within the encoder

Slot 2

Slot 1 Slot 3

Slot 4 FLEX

Main Board

Slot 5 FLEX

F10 Installing the FLEX Decoding ModuleThis section describes how to install the FLEX Decoding Module The modulersquos ports are shown in Figure F-1 on page 45

Host encoders encoders are typically ordered from the factory with the FLEX module already installed However if additional FLEX modules are installed installation of the FLEX module in the field would be required

F1001 ESD Safety Precautions

To protect modules from electrostatic discharge (ESD) follow these safety precautions

Always wear a properly grounded antistatic wrist strap whenever handling the modules

Keep the module inside the antistatic bag until you are ready to install the module in a chassis

F101 Installing a ModuleBefore installing the FLEX module you may need to upgrade the software version on the encoder Contact Harmonic Customer Support to find out which software version you need to install the additional module

There is also a CPC limitation that requires version 105

NOTE Before making changes to the FLEX module make sure the service configuration is cleared before powering down the system Also before installing the FLEX module make sure that the encoder has the appropriate software version installed before installing the module using either NMX or SAG

NOTE The FLEX module must be installed in slot 4 (and an optional second module in slot 5) of the encoder

You need a Phillipstrade screwdriver to install the FLEX module

To install the FLEX module

1 Turn off the encoder in which you are installing the module

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 57: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix F DiviComtrade FLEX Decoding Module Cabling the FLEX Module

copy 2011 Harmonic Inc 52 Ion AVC SD Version 30 Rev K

2 Remove the protective covers from slots 1 through 5 where you are going to install the module (by loosening the two screws with the Phillips screwdriver)

Save the cover for future use

3 While wearing an ESD wrist strap unpack the module from its antistatic protective packing material

CAUTION Unpack and handle the module away from electric motors transformers and other similar machinery

4 Slide the module onto the encoder by lining up the edges of the module with the slots in the chassis

Make sure that the FLEX module goes into the encoder smoothly without binding or scraping other modules The modules should slide easily until you feel the module engage the internal connector and the module is flush with the back of the encoder Do not force the module

5 Tighten the two screws with the screwdriver

NOTE Refer to the encoder guide or online help for information about accommodating the new FLEX module in the encoderrsquos configuration

F11 Cabling the FLEX ModuleThis section describes how to cable the FLEX module Cabling the FLEX module is very straight forward All video and monitor ports are clearly marked The following table lists the ports and required connectors

NOTE Video ports can either be used for loopback or confidence monitoring

Each firmware license ships with two video loopback cables An optional adapter cable can be purchased for use with the monitoring ports You must also have an IP input module installed Figure F-3 on page 53 provides additional information on understanding the encoderrsquos LED color values

F12 Re-Encode Chassis Scenarios This section describes two recommended re-encode chassis scenarios 2- Channel and 4-Channel scenarios

F121 2 - ChannelFigure F-1 on page 45 illustrates a typical 2-channel re-encode chassis cabling assignment This scenario makes use of a base 2-channel encoder chassis Table F-8 describes the port and cable associations

NOTE For the monitor ports there is a DIN to BNC pigtail connector that can be ordered Harmonic Part number FLEX-MON 229-0054067

Table F-8 Port and Cable Assignments (2-channel)

Port Description Connector

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 58: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix F DiviComtrade FLEX Decoding Module Re-Encode Chassis Scenarios

copy 2011 Harmonic Inc 53 Ion AVC SD Version 30 Rev K

NOTE The FLEX module must use slot 4

Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario

Figure F-3 describes the LED colors and what they represent

720p

Figure F-3 LED Color Chart

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

IP Module

Audio Module

Audio Module

FLEX Module

Attaches to optional SDI monitor (video only)

Table F-8 Port and Cable Assignments (2-channel)

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 59: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix F DiviComtrade FLEX Decoding Module Configuring the FLEX Module in NMX

copy 2011 Harmonic Inc 54 Ion AVC SD Version 30 Rev K

F122 4 - ChannelFigure F-4 illustrates a typical 4-channel re-encode chassis cabling assignment This scenario makes use of a base 4-channel encoder chassis

Table F-9 Port and Cable Assignments

Port Description Connector

Video 1 75 Ω cable DIN 1023

Monitor 1 75 Ω cable This output port is used for the loopback cable that feeds an encoder

DIN 1023

Video 2 75Ω cable DIN 1023

Monitor 2 75 Ω cable The second output port can be used as a monitoring and troubleshooting purposes

DIN 1023

Video 3 75Ω cable DIN 1023

Video 4 75Ω cable DIN 1023

IP Module Audio Module

Attaches to optional SDI monitor

FLEX Module

Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario

F13 Configuring the FLEX Module in NMXRefer to the NMX online help system for configuring a FLEX module for use in your NMX Digital Service Manager application

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 60: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 55 Ion AVC SD Version 30 Rev K

Appendix GDivicomtrade RF Input Card

This appendix contains specifications for the DiviCom RF Input Card

The RF Input card is a four channel ATSC 8VSB receiver It receives four independent ATSC 8VSB signals on its inputs and outputs four MPEG-2 Transport Streams over the chassis internal bus to one or more FLEX decoding modules The RF Input card does not support analog demodulation

The RF Input card can be managed by either NMX or SAG Figure G-1 on page 55 shows a diagram of the rear panel

Figure G-1 RF Input card

The LED lights show status as shown in Table G-1 on page 55

Table G-1 LED status lights

Display Status

Off Port disabled

Blinking Yellow Loss of synch

Red Packet error rate (PER) threshold exceeded

Steady yellow SNR below threshold

Green Port Enabled no alarms

G1 RF SpecificationsThe RF specifications for the card are listed below

VSB Input 4 Type lsquoFrsquo connectors per IEC 60169-24

Tuning Range VHFUHF (Channels 2-59)

NOTE Tuning range is limited to Channels 2 to 59 by software per the FCCIndustry Canada decisions to release channels 60 to 69 for public safety use

Sensitivity --83 dBm6 MHz

Dynamic Range gt 80dB

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 61: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix G Divicomtrade RF Input Card Output Specifications

copy 2011 Harmonic Inc 56 Ion AVC SD Version 30 Rev K

G2 Output SpecificationsThe output specification for the card is

Four MPEG-2 Transport Streams per ATSC A53 Part 3 and ISOIEC 13818-1

G3 Environmental and Physical Compliant with ROHS Directive 200295EC Refer to the encoder environmental specifications for additional information

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 62: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 57 Ion AVC SD Version 30 Rev K

Appendix HAB Power Input Switch

H1 IntroductionThis appendix contains specifications for the AB Power Input switch

The AB Power Input switch receives two separate AC main input sources (to support redundancy) monitors the voltage and selects the good voltage to provide one AC output for input into either the AC or DC power supply The AB Power Input switch automatically changes from the line A input to the Line B input (or the reverse) upon loss of power on the active line The AB Power Input switch uses and monitors the active line continuously and switches to the backup port only when the active line has a fault The unit switches back automatically when the active port is detected as normal and stable (with an appropriate delay)

NOTE The AB Power Input switch is a dual-height card and can only be installed in slots 1 and 3

The AB Power Input switch can be managed by SAG Figure H-1 on page 57 shows a illustration of the AB Power Input switch

Pigtail power output cable(plugs into encoder)

Figure H-1 AB Power Input Switch

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 63: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Appendix H AB Power Input Switch Card Status

copy 2011 Harmonic Inc 58 Ion AVC SD Version 30 Rev K

H2 Card StatusThis section describes how to recognize the current status of the AB Power Input switch through its LEDs

NOTE It is recommended that you use A for primary equipment and B for backup equipment

The LED lights show card status as shown in Table H-1 on page 58

Table H-1 LED status lights

Display Status

Red Input power (for that port) is not within the acceptable voltage range

Green Steady input power for that port is within acceptable voltage rangeFlashing port is being utilized for input power

Orange Port failure (canrsquot be used)

Off No power or broken LED

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 64: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

copy 2011 Harmonic Inc 59 Ion AVC SD Version 30 Rev K

AAC power supply

connecting 26overview 17

agency approvals 3air filters 31 to 32airflow 22alphanumeric keys 28audio cables connecting 25audio compression rates described 39audio encoding features 11audio input ports 17

Bback panel

audio input ports 17described 17Ethernet management port 19 42fault relay port 19fuse 17IP output port 19LEDs 19port specifications 42serial data port 19video input ports 18

boot sequence 45

Ccabling the encoder 25compliance and approval 2connecting

audio input cables 25Ethernet management cable 26IP output cables 26video input cables 26

connections FCC compliance 2connectors

AC power 17digital audio input 17 42Ethernet 19 42fault relay 43IP output 19RJ-45 19 42video 42

cTUVus North American safety approval 3

Ddigital audio

port specifications 42ports 17

digital program insertion 14display front panel 29Dolby Digital AC-3 bit rates 38

Eenvironmental specifications 41Ethernet management port

connecting cable 26described 19specifications 42

European EMIEMC approvals 3

Ffault relay port 19 43FCC compliance 2features

audio encoding 11general 8video encoding 10

filters See air filters 31front bezel 15

removing 24front panel 15 28front panel display 29function keys 28fuse 32

Hhardware specifications 41Harmonic equipment modifying 2Harmonic Heartbeat Protocol 15help displaying on VFD 29HHP 15hot keys 28

Iinput ports 17installing the encoder 21IP output port

connecting cables 26described 19

Kkeypad 28

LLEDs

audio port 20back panel 19front panel 16video port 20

loading new software 46local control panel

described 15display 29

MMAC address viewing 30maintaining air filters 31maintaining fuse 32

Nnavigation keys 28North American EMI approvals 3North American Safety approvals 3

Ooutput port IP 19 26

Ppinouts port 42port specifications 42

Index

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 65: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Index

copy 2011 Harmonic Inc 60 Ion AVC SD Version 30 Rev K

portsaudio input 17Ethernet management 19fault relay 19IP output 19serial data 19video input 18

power supplyAC 26specifications 41

Rrack mounting 21rack rails attaching 23rack-mount kit 21replacing air filters 32resetting the encoder 45RJ-45 connectors 19 42

Sserial data port 19specifications

environment 41fuse 41hardware 41input and output 42port 42power supply 41video 40

standards and approvals 3

TTUV European safety approval 3

Uunpacking the encoder 21

VVFD

display during boot 45paths represented 29

video encoding features 10video input ports

connecting cables 26description 18LEDs 20

video specifications 40

WWEEE compliance 2

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index
Page 66: ION AVC InstallGde - Harmonic Inc · PDF fileDiviCom™ Ion AVC SD Standard Definition H.264 Video Encoder Installation Guide Rev K © 2011 Harmonic Inc. Manual Part No. MAN-IONHW-3.0

Harmonic Inc4300 North First StreetSan Jose CA 95134 USAT +1 408 542 2500 F +1 408 490 6708

wwwharmonicinccom

copy Copyright 2011 Harmonic Inc All rights reserved Manual Part No MAN-IONHW-30

  • Installation Guide
    • Table of Contents
    • Preface
      • 11 Manual Organization
        • Introduction
          • 21 Operating Environment
          • 22 General Features
          • 23 Video Encoding Features
          • 24 Audio Encoding Features
            • 241 Onboard Audio
            • 242 AIC Card
              • 25 AVC Encoding
              • 26 HHP Support
              • 27 Front Panel
                • 271 Front Bezel
                • 272 Local Control Panel
                • 273 LEDs
                • 274 Modes of Operation
                  • 2741 Default Mode
                  • 2742 Verbose Front Panel
                  • 2743 NMX Control Over Second Line
                      • 28 Back Panel
                        • 281 AC Power and Fuse
                        • 282 Audio Input Port
                        • 283 Video Input Ports
                        • 284 IP Output Port
                        • 285 Ethernet Management Port
                        • 286 Fault Relay Port
                        • 287 Serial Data Port
                          • 29 Back Panel LEDs
                            • 291 Main Board LEDs
                            • 292 Audio Port LEDs
                            • 293 Video Lock LEDs
                                • Installation
                                  • 31 Preparation
                                  • 32 Unpacking
                                  • 33 Installing the Encoder in a Rack
                                    • 331 Rack Guidelines
                                    • 332 Chassis Warnings for Rack Mounting and Servicing
                                    • 333 Airflow
                                    • 334 Attaching the Rack Rails
                                    • 335 Mounting the Encoder
                                      • 34 Installing Encoder Software
                                      • 35 Cabling the Encoder
                                        • 351 Back Panel
                                        • 352 Connecting the Audio Input Cables
                                        • 353 Connecting the Video Input Cables
                                        • 354 Connecting the IP Output Cables
                                        • 355 Connecting the Ethernet Management Cable
                                        • 356 Connecting the AC Power
                                            • Operating the Encoder
                                              • 41 Operating with NMX Digital Service Manager
                                              • 42 Using the Front Panel
                                                • 421 The Keypad
                                                • 422 Front Panel Display
                                                • 423 Setting the Encoder Network Properties
                                                  • 4231 Setting the IP Address
                                                  • 4232 Setting the Subnet Mask
                                                  • 4233 Setting the Default Gateway Address
                                                    • 424 Viewing the Encoder MAC Address
                                                    • 425 Viewing the Encoder Serial Number
                                                      • 43 Licensing Information
                                                        • Maintenance and Troubleshooting
                                                          • 51 Air Filters
                                                            • 511 Maintaining the Air Filters
                                                            • 512 Removing and Replacing the Air Filters
                                                              • 5121 Removing and Replacing the Bezel Filter
                                                              • 5122 Removing and Replacing the Keypad Filter
                                                                  • 52 Fuse
                                                                    • 521 Replacing the Fuse
                                                                      • 53 Contacting Harmonic Support
                                                                        • Appendix A
                                                                          • Audio and Video Specifications
                                                                            • A1 AIC Features
                                                                              • Table A-1 AIC Features
                                                                                • A2 On-board Audio Encoding Features
                                                                                  • Table A-2 Onboard Audio Features
                                                                                  • A21 PCM Downmix from 51
                                                                                  • A22 Re-encode Ability
                                                                                    • A3 MPEG-1Layer II Audio
                                                                                      • Table A-3 MPEG-1Layer II Audio Bit Rates
                                                                                        • A4 Dolby Digital (AC-3) Audio
                                                                                          • Table A-4 Dolby Digital (AC-3) Audio Bit Rates
                                                                                            • A5 Video Specifications
                                                                                                • Appendix B
                                                                                                  • Encoder Specifications
                                                                                                    • B1 Environment Specifications
                                                                                                      • Table B-1 Environment Specifications
                                                                                                        • B2 Port Specifications
                                                                                                          • Table B-2 Port Specifications
                                                                                                            • B3 Port Pinouts
                                                                                                              • B31 Ethernet Management Port
                                                                                                                • Table B-3 Ethernet Management Port Pinout
                                                                                                                  • B32 Fault RelayGPI Ports
                                                                                                                    • Table B-4 Fault RelayGPI Port Pinout
                                                                                                                    • Figure B-1 Fault RelayGPI Ports
                                                                                                                        • Appendix C
                                                                                                                          • Encoder Back Panel Slot Locations
                                                                                                                            • C1 Adapter Configurations for All Encoders
                                                                                                                              • Figure C-1 Slot numbers
                                                                                                                              • Table C-1 Supported adaptersmodules and configuration recommendations for this encoder
                                                                                                                              • C11 Additional Card Configurations for FLEX-based Encoders
                                                                                                                                • Table C-2 FLEX Module Options (for use with FLEX module)
                                                                                                                                  • C12 Viewing the Control Board (CPC) Revision Information
                                                                                                                                    • Appendix D
                                                                                                                                      • Boot Sequence
                                                                                                                                        • D1 Local Control Panel Display Messages during Bootup
                                                                                                                                        • D2 Other Local Control Panel Display Messages
                                                                                                                                          • D21 Resetting the Encoder
                                                                                                                                          • D22 Loading New Software
                                                                                                                                            • Appendix E
                                                                                                                                              • Wiring the ndash48 VDC Power Supply
                                                                                                                                                • E1 Getting Started
                                                                                                                                                • E2 Power Source Specifications
                                                                                                                                                  • Table E-1 Power Source Specifications
                                                                                                                                                    • E3 Overcurrent Protection
                                                                                                                                                    • E4 Wiring Requirements
                                                                                                                                                      • Table E-2 Recommended Wire Specifications
                                                                                                                                                        • E5 Power Connector
                                                                                                                                                          • Figure E-1 CableStrain Relief Housing
                                                                                                                                                            • E6 Assembling the DC Input Power Cable
                                                                                                                                                              • Figure E-2 Pin Out Specification
                                                                                                                                                                • Appendix F
                                                                                                                                                                  • DiviComtrade FLEX Decoding Module
                                                                                                                                                                    • F1 Introduction
                                                                                                                                                                      • Figure F-1 FLEX Module Ports
                                                                                                                                                                        • F2 Video Decoding Specifications
                                                                                                                                                                          • Table F-1 Video Decoding Features
                                                                                                                                                                            • F3 Audio Passthrough Specifications
                                                                                                                                                                              • Table F-2 Audio Passthrough Specifications
                                                                                                                                                                                • F4 Audio Decode Specifications
                                                                                                                                                                                  • F41 Decoding Resource Considerations
                                                                                                                                                                                    • Table F-3 AC-3 Resource Considerations
                                                                                                                                                                                    • Table F-4 MPEG-L2 Resource Considerations
                                                                                                                                                                                        • F5 Ancillary Data Specifications
                                                                                                                                                                                          • Table F-5 Ancillary Data Specifications
                                                                                                                                                                                            • F6 Input Specifications
                                                                                                                                                                                              • Table F-6 Input Specifications
                                                                                                                                                                                                • F7 Output Specifications
                                                                                                                                                                                                  • Table F-7 Outputs Specifications
                                                                                                                                                                                                    • F8 Environmental and Physical
                                                                                                                                                                                                    • F9 Module Slots
                                                                                                                                                                                                    • F10 Installing the FLEX Decoding Module
                                                                                                                                                                                                      • F1001 ESD Safety Precautions
                                                                                                                                                                                                      • F101 Installing a Module
                                                                                                                                                                                                        • F11 Cabling the FLEX Module
                                                                                                                                                                                                        • F12 Re-Encode Chassis Scenarios
                                                                                                                                                                                                          • F121 2 - Channel
                                                                                                                                                                                                            • Table F-8 Port and Cable Assignments (2-channel)
                                                                                                                                                                                                            • Figure F-2 2 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                            • Figure F-3 LED Color Chart
                                                                                                                                                                                                              • F122 4 - Channel
                                                                                                                                                                                                                • Table F-9 Port and Cable Assignments
                                                                                                                                                                                                                • Figure F-4 4 - Channel Re-Encode Chassis (Cable) Scenario
                                                                                                                                                                                                                    • F13 Configuring the FLEX Module in NMX
                                                                                                                                                                                                                        • Appendix G
                                                                                                                                                                                                                          • Divicomtrade RF Input Card
                                                                                                                                                                                                                            • Figure G-1 RF Input card
                                                                                                                                                                                                                            • Table G-1 LED status lights
                                                                                                                                                                                                                            • G1 RF Specifications
                                                                                                                                                                                                                            • G2 Output Specifications
                                                                                                                                                                                                                            • G3 Environmental and Physical
                                                                                                                                                                                                                                • Appendix H
                                                                                                                                                                                                                                  • AB Power Input Switch
                                                                                                                                                                                                                                    • H1 Introduction
                                                                                                                                                                                                                                      • Figure H-1 AB Power Input Switch
                                                                                                                                                                                                                                        • H2 Card Status
                                                                                                                                                                                                                                          • Table H-1 LED status lights
                                                                                                                                                                                                                                          • A
                                                                                                                                                                                                                                          • B
                                                                                                                                                                                                                                          • C
                                                                                                                                                                                                                                          • D
                                                                                                                                                                                                                                          • E
                                                                                                                                                                                                                                          • F
                                                                                                                                                                                                                                          • H
                                                                                                                                                                                                                                          • I
                                                                                                                                                                                                                                          • K
                                                                                                                                                                                                                                          • L
                                                                                                                                                                                                                                          • M
                                                                                                                                                                                                                                          • N
                                                                                                                                                                                                                                          • O
                                                                                                                                                                                                                                          • P
                                                                                                                                                                                                                                          • R
                                                                                                                                                                                                                                          • S
                                                                                                                                                                                                                                          • T
                                                                                                                                                                                                                                          • U
                                                                                                                                                                                                                                          • V
                                                                                                                                                                                                                                          • W
                                                                                                                                                                                                                                            • Index