8/12/2019 InteliNano-AMF-1.5 - Fast User Guide

1/2

ComAp, a.s.Kundratka 2359/17180 00, Praha 8Czech Republic

InteliNano-NT AMF, SW version 1.5, ComApSeptember 2013 1InteliNano-NT-AMF-1.5-Fast User Guid.pdf

CAN INTERFACE

MAINS VOLTAGE

MEASUREMENT

T20 = Neutral

T21 = Phase 1

T22 = Phase 2

T23 = Phase 3

GENERATOR VOLTAGE

MEASUREMENT

T16 = Neutral

T17 = Phase 1

T18 = Phase 2

T19 = Phase 3

USB interface

L

COM

H

INTPUT TERMINALS

T10 = COM for analog inputs

T11 = binary input

T12 = binary input

T13 = binary/analog inputLow Fuel Level

T14 = binary/analog inputCoolan Temperature

T15 = binary/analog inputOil Pressure

OUTPUT TERMINALS

T04 = binary outputStarter (6A)

T05 = binary output - Fuel Solenoid (6A)

T06 = binary output (500 mA)

T07 = binary input/output (500 mA)

T08 = binary output (500 mA)

T09 = binary output (500 mA)

POWER SUPPLY, D+

T01 = BATT -

T02 = D+

T03 = BATT +

GECU

D IE SE L / GA SO LI NE EN GI NE G EN ER AT OR

LOAD

FuelSolenoid

Battery

Sarter

FuelLevelAnalog

CoolantTemperatureAnalog

OilPressureAnalog

D+

-

+

GCB MCB

GCB

MCB

Alarm

ReadyToLoad

FuelSolenoid

Starter

COM

RemoteStartAndLoad

EmergencyStop

CAN

LCOMHU

SB

Battery+

Battery-

D+

PC

L1

L2

L3

N

InteliNano NTAMF

Fast User Guide

Typical wiring diagram

Accessing the setup mode

Ensure the engine is stopped and the controller is in Manual mode (green LED above buttonAutois turned off).If you have not configured the custom initialization (init) screen then press and hold Stopbutton, then briefly press buttonand then Auto.

If you have already created your own init screen then press and hold Stopbutton and then briefly press , the custom init screen will appear, keep holding the Stop

button. Then pressto switch LCD to default init screen, and then press Auto.To move up and down in the setup menu useandbuttons. PressStartbutton to select orStopbutton for exit.

Basic set t ings Output set t ings

Engine parameters and protect ions Input set t ings

Generator protect ions ECU setting

AMF(Auto Mains Failure) set t ings Info

Outputs and inputs

Outputcode

Output source Type Terminal assignment

O00 Not Used binary T04, T05, T06, T07, T08, T09

O01 Starter binary T04

O02 Fuel Solenoid binary T04, T05, T06, T07, T08, T09

O03 Stop Solenoid binary T04, T05, T06, T07, T08, T09

O04 Alarm binary T04, T05, T06, T07, T08, T09

O05 GCB Close/Open binary T04, T05, T06, T07, T08, T09O06 MCB Close/Open binary T04, T05, T06, T07, T08, T09

O07 Ready To Load binary T04, T05, T06, T07, T08, T09

O08 Prestart binary T04, T05, T06, T07, T08, T09

O09 ECU Power Relay binary T04, T05, T06, T07, T08, T09

O10 Choke binary T04, T05, T06, T07, T08, T09

O11 Glow Plugs binary T04, T05, T06, T07, T08, T09

Normally Open ContactoutputNormally Open Contact - inputbutton

Normally Closed ContactoutputNormally Closed Contactinputbutton

User curves

I21 I23 I25

VDO Level % VDO 5 Bar VDO 40-120 C

Datcon Level % VDO 10 Bar VDO 50-150 C

Datcon 5 Bar Datcon High C

Datcon 7 Bar Datcon Low C

Datcon 10 Bar

Not selected Not selected Not selected

Inputcode

Input source Type Terminal assignment

I00 Not Used binary T07, T11, T12, T13, T14, T15

I01 Emergency Stop binary T07, T11, T12, T13, T14, T15

I02 Remote Start/Stop binary T11

I03 Remote Start And Load binary T11

I04 Access Lock binary T07, T11, T12, T13, T14, T15

I05 AMF Block ed binary T07, T11, T12, T13, T14, T15

I06 MCB Feedback binary T07, T11, T12, T13, T14, T15

I07 GCB Feedback binary T07, T11, T12, T13, T14, T15

I10 External Warning 1 binary T07, T11, T12, T13, T14, T15

I11 External Warning 2 binary T07, T11, T12, T13, T14, T15

I12 External Warning 3 binary T07, T11, T12, T13, T14, T15

I13 External Shutdo wn 1 binary T07, T11, T12, T13,T14, T15

I14 External Shutdo wn 2 binary T07, T11, T12, T13, T14, T15

I15 External Shutdo wn 3 binary T07, T11, T12, T13, T14, T15

I20 Low Fuel Level binary T07, T11, T12, T13, T14, T15

I21 Fuel Level Analog analog T13, T14, T15

I22 Low Oil Pressure binary T07, T11, T12, T13, T14, T15

I23 Oil Pressure Analog analog T13, T14, T15

I24 High Coolant Temperature binary T07, T11, T12, T13, T14, T15

I25 Coolant Temperature Analog analog T13, T14, T15

I29 Fuel Level SD Binary T07, T11, T12, T13, T14, T15

DimensionsCase dimensions:118mm x108mm x 40mm

Panel Cutout: 96mm x 96mm

WARNING!If D+ is not used, connect this terminal to battery positive!

8/12/2019 InteliNano-AMF-1.5 - Fast User Guide

2/2

ComAp, a.s.Kundratka 2359/17180 00, Praha 8Czech Republic

InteliNano-NT AMF, SW version 1.5, ComApSeptember 2013 2InteliNano-NT-AMF-1.5-Fast User Guid.pdf

Setpoints

Useandbuttons to move or change value. Startbutton to select setpoint or confirm changes and Stopbutton to go back.

Basic set t ings

Setpointcode

Setpoint name

B01 Nomin al Voltage Ph-N 80480 V

B02 Nomin al Voltage Ph-Ph 80600 V

B03 Nominal Frequency 50 Hz (1), 60 Hz (2)

B04 Connect ion Type

Mono Phase (1), SplitPhase (2),3Ph3Wire (3), 3Ph4Wire (4),

Autodetect (5)

B05 Units FormatMetric unit format (1), US unitformat (2)

B06 AMF Funct ion Disable (1), Enable (2)

B07 Zero Power Mode Delay 0-360 min

B08 Light Tower Mode Disable (1), Enable (2)

B09 Nomin al RPM 100-4000

Engine parameters and protect ions

Setpointcode

Setpoint name

E01 Prestart Time 0-600 s

E02 Maximum Cranking Time 0-60 s

E03 Cooling Time 0-3600 s

E04 Oil Pressure Shutdown 0-10 Bar

E05 Coolant Temperature Shutdown 0 -150 C

E15 Fuel Level Shutdown 020%

E06 Battery Undervo ltage 840 V

E07 Warnin g Maintenance 010000 h

E08 Oil Pressure Starter Disengagem ent Disable (1), Enable (2)

E09 Chok e Time 0 3600 s

E10 Minim al Stabilization Time 1 300 s

Generator protect ions

Setpointcode

Setpoint name

G01 Generator Overvoltage Shutdown G02200 %

G02 Generator Undervoltage Shutdown 0 - G01%

G03 Generator Overf requency Shutdown G04130 %

G04 Generator Underf requency Shutdown 0G03%

AMF(Auto Mains Failure) set t ings

Setpointcode

Setpoint name

A01 Emergenc y Start Delay 0600 s

A02 Mains Return Delay 13600 s

A03 Mains Overvoltage A04150 %

A04 Mains Undervoltage 50A03

A05 Mains Overf requency A06150 %A06 Mains Underf requency 50A05 %

To apply all changes return to the main setup menu and restart the controller by pressing theStopbutton.

Alarms and Events

Events

Mains Return

Mains Fail

Manual Start

Remote Start

AMF Start

Manual Stop

Remote Stop

AMF Stop

Auto On

Auto Off

Power On

Island Operation

Warnings

Warning Maintenance

Low Bat tery

Low Fuel Level

External Warning 1

External Warning 2

External Warning 3

ECU Communicat ion Error

MCB Fail

Mains CCW Rotat ion

Shutdowns

Emergency Stop

Overspeed

Underspeed

Low Oil Pressure

High Coolant temperature

External Shutdown 1

External Shutdown 2

External Shutdown 3

GCB Fail

Generator Overvoltage

Generator Undervoltage

Generator Overf requency

Generator Underf requency

Generator CCW Rotation

Start Fail

Stop Fail

Battery Flat

Voltage Autodetect

Fuel Level SD

ECU

For ECU configuration use PC software NanoEdit. For more details see InteliNano AMF Reference Guide.Technic al data

Power supply range 6-36 VDC

Power supply drop-out immunity 100 ms

Power consumption 35295 mA

Zero Power Mode consumption 52 - 344 A

Operating temperature -20... 70 C

Operating humidity 95 % non-condensing (IEC/EN 60068-2-30)

Protection degree (front panel)IP65 with GASKET 4x405 only

IP50 without gasket

Storage temperature -30... 80 C

Binary outputs (up to 6)

Low current outputs (4) 500 mA

High current output (2) 6 A (long term) / 10 A (short term)

Total output current 10 A (long term) / 16 A (short term)

Binary inputs (up to 6)

Input resistance 1,5 k

Closed contact voltage 3,5 V

Analog inputs (up to 3)

Galvanic insulation Not insulated

Electrical range 0 - 2500 k

Resolution 0,1

Precision 2 % 3

Charging alternator preexcitation circuit

Excitation current 100 mA

Charging fail threshold 80 %

Generator/Mains measurements

Measurement input 3ph generator voltage, 3ph mains voltage

Measurement type True RMS

Voltage range 480 V Ph-Ph (277 V Ph-N)

Max. measured voltage 340 V Ph-NVoltage accuracy 1 %

Frequency range 4070 Hz

Frequency accuracy 1 %