Upload
seawave
View
427
Download
8
Embed Size (px)
Citation preview
Chemical Engineering Department
2009/2010
INTEGRATED NGL RECOVERY AND LNG LIQUEFACTION
Graduation project technical report
Cairo University
Chemical Engineering Department
Faculty of Engineering
Integrated NGL Recovery And LNG liquefaction
i
Authors
Project Supervisor
Dr. Ahmed Soliman
Date
Monday, February 22, 2010
Name Section B.N. Ahmed Mohsen Khedr 1 15
Ahmed Hesham Rezk 1 21
Serag El Dine Magdi Mohamed 2 29
Abd El Rahman Magdi Ali 2 38
Ali Ahmed Sadek Nada 2 41
Ali Baiuomy Ali Mahmoud 3 1
Karim Mohamed Reda Abd El Hamid 3 8
Mohamed Osama Ahmed Kamal 3 18
Mohamed Hassan Mohamed Morsy 3 21
Mohanad Mohie El Dine Ismael 4 15
Youssef Alaa El Din Hassanein 4 40
Integrated NGL Recovery And LNG liquefaction
ii
Table of Contents
1. Introduction………………………………………………………………………….. 1
1.1. A brief history of LNG & NGL production ………….………………………….. 1
1.2. Properties of raw natural gas………………………..…………………................. 3
1.2.1 Viscosity…………………………………………………………..……………….. 3
1.2.2 Gas hydrates…………………..……..…………………………………………….. 5
1.2.3 Calorific value of natural gas…………………………..…………….................... 5
1.3. Some properties of liquefied natural gas…………………………..……………... 6
1.4. Abundance of natural gas in egypt……………………………...………………... 6
1.5. Safety & health aspects………………….……………………………………........ 7
1.5.1. Primary containment…………………...………………………………..………. 8
1.5.2. Secondary containment………………….………………………………………. 9
1.5.3. Safeguard systems……………………….……………………………………….. 9
1.5.4. Separation distance……………………………………………………………….. 9
1.6. Markets……………………….…………………………………………………..... 10
1.6.1. Global markets……………………..…………………………………………….. 10
1.6.2. Local markets…………………….……………………………………………….. 13
1.6.3. Cost…………..……………...…………………………………………………….. 14
Page
Integrated NGL Recovery And LNG liquefaction
iii
1.6.3.1. LNG value chain……………………………………………………………….. 14
1.6.3.2. Linkage between markets……………..………..……………………………… 15
1.6.3.3. LNG prices……………..……………………………………………………….. 15
1.6.3.4. NGL prices…….………………….…………………………………………….. 15
2. Natural gas processing from well till production of LNG………………….……... 16
3. Pre-treatment of natural gas………………………………..………………………. 17
3.1. Objectives of natural gas treating…………………………………………………. 18
3.2. Sweetening………………………………………………………………………...... 18
3.3. Dehydration……………………………………………………………………..….. 20
3.3.1 Cryogenic dehydration……………..……………………….…………………….. 20
3.3.2 Dehydration by absorption processes……………..………………….………….. 21
3.3.3 Adsorptive dehydration……………….……..………………...…………………. 22
3.4. Removal of mercury……………………..…..…………………………………….. 23
4. Available technologies for LNG-NGL production……………..………………….. 24
4.1. Traditional stand-alone gas plant upstream of liquefaction plant ……………... 24
4.2. Process schemes for lng train in the downstream of a liquefaction plant..…….. 25
4.2.1 The most commonly utilized lng technologies…………………………………... 26
4.2.1.1 APCI propane pre-cooled mixed refrigerant process……….………………... 26
4.2.1.2 COP LNGsm process…………………………………………………..………… 27
Page
Integrated NGL Recovery And LNG liquefaction
iv
4.3. Integrated NGL and LNG plants…………………………………….…………… 28
4.3.1 Introduction….…………………………………………………………………….. 28
4.3.2 Available techniques………………..…………………………………………….. 29
4.3.2.1 LNG facility with integrated NGL extraction technology for enhanced NGL recovery and product flexibility…………….................................... 29
FIRST CONFIGURATION………………………………………..……………………….. 30 SECOND CONFIGURATION ……………………………..………………………………. 32 THIRD CONFIGURATION ….……………………………………………………………. 34
4.3.2.2 Intermediate pressure LNG refluxed NGL recovery process……………….. 36
4.3.2.3 Configurations and methods of integrated NGL recovery and LNG liquefaction……………………………………………………………………………... 38
4.3.2.4 Integrated NGL recovery and LNG liquefaction………………………..… 40
5. Storage & transportation…………………………………………..……………….. 41
5.1. Storage…….……………………...………………………………………………… 41
5.1.1. Methods of operation in tanks…………….…………………………………….. 42
5.2. Transportation…….……………………………………………………………….. 42
6. Regasification...……………………………………………………………………….. 44
7. Proposed technology…………………………………………………………………. 45
7.1. Precooling of feed gas…………………………..……….…………………………. 46
7.2. Separation of C2+ from feed gas………………………………………………….. 46
7.3. Liquefaction unit…………………………………...………………………………. 47
Page
Integrated NGL Recovery And LNG liquefaction
v
7.4. C2 liquid recovery……………………………………………….……...………….. 48
7.5. C3 liquid recovery……………………………………………………………..….... 48
7.6. C4 liquid recovery………………………………………………………….…….… 48
7.7. Refrigeration cycles……………………………………………..……………….… 49
8. References………………………………………………………………………………….... 50
Page
Integrated NGL Recovery And LNG liquefaction
vi
List of Figures
Figure 1: Viscosity of paraffin hydrocarbon gases at 1 atm as a function of molar mass……………...…………………………………………………………………….… 4
Figure 2: Viscosity ratio as a function of pseudoreduced temperature.……….……. 4
Figure 3: Natural gas & oil fields in Egypt ……………………...…………………… 7
Figure 4: World natural gas reserves by country as of January 2009…………....… 10
Figure 5: Country share of world LNG production 2008…….…………...……….... 11
Figure 6: LNG projects in Egypt……………………………………………………… 14
Figure 7: LNG value chain……………………………………………………….…… 14
Figure 8: LNG process....…………….…………………………………………..….... 16
Figure 9: Flow diagram of the amine process for gas sweetening................................ 19
Figure 10: Dehydration with a hydrate inhibitor and cooling at a high-pressure well……………………………………………………………………………………… 21
Figure 11: Glycol dehydration…………….………………………………………...... 21
Figure 12: Hydrocarbon removal with adsorption and regeneration under pressure………………………………………………………………………………… 22
Figure 13: Block diagram for typical ngl extraction plant………………………..... 24
Figure 14: Flow diagram for APCI propane pre-cooled mixed refrigerant process. 26
Figure 15: Flow diagram for Phillips optimized cascade process............................... 27
Figure 16: Block diagram showing the integrated NGL and LNG process..…….… 28
Page
Integrated NGL Recovery And LNG liquefaction
vii
Figure 17: A flow diagram showing integrated heavies removal/NGL recovery system…………………………………………………………………………………….. 30
Figure 18: A simplified flow diagram of a cascaded refrigeration process for producing LNG……………...……………………………………………………...…… 31
Figure 19: A flow diagram showing integrated heavies removal/NGL recovery system connected to the LNG facility of fig 20...……………………………. 32
Figure 20: A simplified flow diagram of a cascaded refrigeration process for producing LNG……………...……………………………………………………...…… 33
Figure 21: A flow diagram showing integrated heavies removal/NGL recovery system…………………………….…………………………………………………..…... 34
Figure 22: A simplified flow diagram of a cascaded refrigeration process for producing LNG…………………………………………...………………………...…… 35
Figure 23: Simplified schematic flow diagram of an LNG facility that employs an intermediate pressure distillation column……………………………………………. 36
Figure 24: Simplified schematic flow diagram of an LNG facility that employs an intermediate pressure distillation column……………………………………………. 37
Figure 25: A schematic of one exemplary plant configuration using a twin column configuration for production of cold compressed overhead product and separation of C2 and C3……………………….…….......................................................................... 38
Figure 26: A more detailed schematic of an exemplary plant according to figure 25 with two cascade refrigeration cycles and one mixed refrigerant cycles for NGL recovery and LNG liquefaction……………………….………………………………… 39
Figure 27: A schematic flow diagram of an exemplary plant Configuration…..…… 40
Figure 28: LNG ship types……………………………………………………..……… 43
Figure 29: Cross-section of LNG tanker………………………………..…..………… 43
Figure 30: Simplified flow diagram of a typical LNG regasification system……...... 44
Page
Integrated NGL Recovery And LNG liquefaction
viii
Figure 31: Proposed technology process flow diagram…………………….…..……..… 45
List of Tables
Table 1: Physical properties of natural gas components at STP…………………..... 3
Table 2: Calorific values of natural gas components at STP……………………….... 5
Table 3: LNG exporting countries and startup date of earliest liquefaction terminals………………………………………………………………………………..... 12
Table 4: LNG importing countries and startup date of earliest regasification terminals………………………………………………………………..……………….. 12
Page
Integrated NGL Recovery And LNG liquefaction
ix
Abstract The combination of changing global markets for natural gas liquids (NGL) with the
simultaneous increase in global demand for liquefied natural gas (LNG) has stimulated an
interest in the integration of NGL recovery technology with LNG liquefaction technologies.
Historically, the removal of heavy hydrocarbons from the feed to LNG plants has been
characterized as “gas conditioning” and achieved using one or more distillation columns.
While some attempts to provide reflux to the distillation columns marginally enhanced NGL
recovery, little emphasis was placed on maximizing NGL recovery as a product from the
LNG process. As such, the integration of the two processes was not a priority.
Integrating NGL recovery technology within the LNG Process, results in a significant
reduction in the specific power required to produce LNG, while maximizing NGL recovery.
This corresponds to a production increase in both LNG and NGL for comparable
compression schemes as compared to stand-alone LNG liquefaction and NGL extraction
facilities. In addition, there are potential enhancements to the overall facility availability and
project economics using the integrated concept.
Integrated NGL Recovery And LNG liquefaction
1
1. Introduction Due to clean burning characteristics and the ability to meet stringent environmental
requirements, the demand for natural gas has increased considerably over the past few years.
Projections reflect a continued increase for the next several years. However, it is a clean
burning methane rich gas that is in demand as opposed to the typical raw gas that exists in
nature, which often includes additional components such as heavier hydrocarbons and other
impurities. The heavier hydrocarbons, once separated from natural gas, are referred to as
Natural Gas Liquids (NGL).
Natural gas must be conditioned prior to liquefaction to remove undesired components. This
conditioning normally takes place in separate or stand-alone facilities and typically includes
the extraction of heavier hydrocarbons (NGL). The conditioned gas is then typically fed to
pipelines for distribution. However, transportation to distant markets through gas pipelines is
not always economically or technically feasible. As such, natural gas liquefaction has
become a viable and widely accepted alternative.
Therefore, LNG is a natural alternative for gas pipelines when transporting natural gas to
distant places and it should be emphasized that LNG is natural gas (mainly methane) that
has been cooled to the point that it condenses to a liquid, which occurs at a temperature of
approximately -256o F (-161o C) at atmospheric pressure. Liquefaction reduces the volume
of gas by approximately 600 times.
Also NGL is a liquid hydrocarbon mixture which is gaseous at reservoir temperatures and
pressures, but recoverable by condensation or absorption. It consists mainly of the higher
hydrocarbons in natural gas (ethane and above).
1.1. A Brief History of LNG & NGL Production Natural gas liquefaction dates back to the 19th century when British chemist and
physicist Michael Faraday experimented with liquefying different types of gases,
Integrated NGL Recovery And LNG liquefaction
2
including natural gas. German engineer Karl Von Linde built the first practical
compressor refrigeration machine in Munich in 1873. The first LNG plant was built in
West Virginia in 1912 and began operation in 1917. The first commercial liquefaction
plant was built in Cleveland, Ohio, in 1941. The LNG was stored in tanks at atmospheric
pressure. The liquefaction of natural gas raised the possibility of its transportation to
distant destinations. In January 1959, the world's first LNG tanker (The Methane
Pioneer) containing 7,000 barrel equivalent aluminum prismatic tanks with balsa wood
supports and insulation of plywood and urethane carried an LNG cargo from Lake
Charles, Louisiana to Canvey Island, United Kingdom. This event demonstrated that
large quantities of liquefied natural gas could be transported safely across the ocean.
Over the next 14 months, seven additional cargoes were delivered with only minor
problems. Following the successful performance of The Methane Pioneer, the British
Gas Council proceeded with plans to implement a commercial project to import LNG
from Venezuela to Canvey Island.
After the concept was shown to work in the United Kingdom, additional liquefaction
plants and import terminals were constructed in both the Atlantic and Pacific regions.
Four marine terminals were built in the United States between 1971 and 1980. The LNG
market in both Europe and Asia continued to grow rapidly from that point on.
On the other hand, the NGL industry started after the early 1960s in conjunction with
liquefaction of natural gas, since before this date, it was considered as one of the steps of
conditioning of natural gas before liquefaction, and gas produced was routinely flared as
a useless by-product.
The start of the NGL industry was due to the awareness of the major oil producers in the
world of energy conservation, and consequently at this point in time, most of the
associated gas (gas produced in conjunction with crude oil) was being gathered with the
heavies produced from natural gas and used for NGL and fuel-gas production.
Integrated NGL Recovery And LNG liquefaction
3
1.2. Properties of Raw Natural Gas • It is colorless and odorless.
• It is lighter than air with a specific gravity of about 0.6-0.8. If leaks, it disperses
upward and dissipates into the air quickly.
• It is inflamed during a range of 5-15% by volume of gas in air. The self-ignition
temperature of natural gas is 537-540 Celsius degrees.
• As it is a clean fuel with cleaner burning nature, natural gas has lower environmental
impact when compared with other types of fuel.
• It is hydrocarbon component with methane as a major component.
Compound Molar mass, kg/kmol
Molar volume, m3/kmol
Density, kg/m3
Relative density, (air = 1)
Methane 16.043 22.360 0.7175 0.5549 Ethane 30.069 22.191 1.355 1.048 Propane 44.096 21.928 2.011 1.555 n-Butane 58.123 21.461 2.708 2.094 Isobutane 58.123 21.550 2.697 2.086 n-Pentane 72.150* 20.90* 3.452* 2.670* Isopentane 72.150* 21.06* 3.426* 2.650* n-Hexane 86.177* 20.10* 4.29* 3.315* n-Heptane 100.203* 18.3* 5.48* 4.235* Nitrogen 28.0134 22.403 1.2504 0.9671 Carbon Dioxide 44.0098 22.261 1.9770 1.5290 Hydrogen Sulfide
34.076 22.192 1.5355 1.1875
Helium 4.0026 22.426 0.17848 0.1380 * Compound in liquid state at STP
1.2.1 Viscosity
For an ideal gas, the pressure and temperature dependence of viscosity is opposite to
that of liquids; the viscosity of an ideal gas increases with increasing temperature and
is independent of pressure. Actual hydrocarbon gases, however, deviate from ideal
behavior and approach that of liquids; their viscosity increases with increasing
Table 1: Physical properties of natural gas components at STP
Integrated NGL Recovery And LNG liquefaction
4
pressure, and decreases with increasing temperature at intermediate or high pressure.
Figure 1 is employed for estimating the dynamic viscosity µgas of natural gases
composed primarily of hydrocarbons at atmospheric pressure. The presence of
carbon dioxide, hydrogen sulfide, and nitrogen increases the viscosity. The viscosity
µg at any desired temperature and pressure can be obtained from Figure 2, where the
ratio µg/µga is plotted as a function of the pseudoreduced temperature and pressure.
The pseudocritical pressure and temperature are then used to determine the
pseudoreduced conditions:
ppr = 𝑝𝑝𝑝𝑝𝑝𝑝𝑝𝑝
, ppc=∑yipci Tpr = 𝑇𝑇𝑇𝑇𝑝𝑝𝑝𝑝
, Tpc=∑yiTci
Where Tc and pc are the critical point conditions, and T and p are the values of
the system, respectively.
Figure 2: Viscosity ratio as a function of pseudoreduced temperature
Figure 1: Viscosity of paraffin hydrocarbon gases at 1 atm as a function of molar mass
Integrated NGL Recovery And LNG liquefaction
5
1.2.2 Gas Hydrates
Gas hydrates are ice like solids composed of water and hydrocarbons. Hydrocarbons
ranging from methane to cyclopentane are known to form hydrates. The formation of
hydrates depends on pressure, temperature, molecular size, and concentration of the
component. Generally, hydrates form at high pressure and low temperature, but they
can occur as high as 30 0C and below 0.7 MPa. Hydrate formation can be predicted
from empirical vapor – solid equilibrium ratios, empirical correlations, and
laboratory measurements. To avoid the formation of gas hydrates in pipelines, the
water vapor content of natural gas is commonly reduced by dehydration before
transport. Lowering the water dew point to −5 to −8 0C in relation to the maximum
transmission pressure is a common tipulation in gas specifications.
1.2.3 Calorific Value of Natural Gas
H=∑yiHi, where Hi is the gross or net calorific value.
Compound Gross calorific value MJ/m3
Net calorific value MJ/m3
Methane 39.819 35.883 Ethane 70.293 64.345 Propane 101.242 93.215 n-Butane 134.061 123.810 Isobutane 133.119 122.910 n-Pentane 169.19* 156.56* Isopentane 167.53* 154.99* n-Hexane 208.70* 193.38* n-Heptane 265.22* 245.99* Hydrogen sulfide 25.336 23.353 * Compound in liquid state at STP
Table 2: Calorific values of natural gas components at STP
Integrated NGL Recovery And LNG liquefaction
6
1.3. Some Properties of Liquefied Natural Gas
• LNG is predominantly methane (CH4) converted to liquid for ease of storage and
transportation by cooling it to -260 0F or -160 0C.
• LNG takes up 1/600th
the volume of natural gas in the gaseous form.
• LNG density is approximately 26.5 lb/cu ft which is lighter than water (65 lb/cu ft)
• LNG is an odorless, non-toxic and non-corrosive liquid, if spilled would not result in
slick. Absent an ignition source LNG evaporates quickly and disperses leaving no
residue.
• No environmental cleanup needed for LNG spills on water or land
• LNG offers an energy density comparable to petrol and diesel fuels simultaneously
producing less pollution.
1.4. Abundance of Natural Gas in Egypt
Most current exploration and production are sourced in the Nile Delta region and in the
Western Desert. The Abu Madi, Badreddin and Abu Qir fields in the Nile Delta account
for approximately one-half of Egypt's gas production, and are non-associated and mature
fields. Other offshore developments include Port Fouad, South Temsah, Wakah, Rosetta,
the Scarab/Saffron fields and the newly discovered Satis field found by BP and Eni in
early 2008. In the Western Desert, the Obeiyed and Khalda fields are the most important
natural gas areas, these fields have lower development and operating costs than fields in
the Mediterranean region due to an expanding network of pipelines and processing
plants that allow for quick transport upstream to Alexandria via a 180-mile pipeline.
Integrated NGL Recovery And LNG liquefaction
7
1.5. Safety & Health Aspects Liquefied natural gas may be viewed as a creation of the modern era, and as such, it has
been subjected to more thorough scrutiny than traditional fuels such as gasoline and fuel
oil. The hazards associated with LNG are that it is a low-temperature fluid, is flammable,
and can create vapor clouds dense enough to cause asphyxiation. Because none of these
is a problem when LNG is contained in properly designed storage tanks or piping and
equipment, safety studies have generally focused on LNG spills. In LNG facilities,
extensive safety systems exist to detect gas leaks, to detect and counter fires, and to
detect smoke. Spill prevention and containment are implicit in the design of plant
facilities, particularly of storage tanks because they contain the greatest quantity of
LNG.
If an LNG spill is ignited soon after it occurs, a pool fire results. This fire is certainly a
problem, but it is contained in a facility staffed and equipped to deal with such
Figure 3: Natural Gas & Oil Fields in Egypt
Integrated NGL Recovery And LNG liquefaction
8
emergencies. A greater concern is that the same spill may be given sufficient time to
evaporate and form a vapor cloud that can travel for some distance before ignition.
A number of variables such as the nature of the surface underneath the spill, the wind
velocity, and the presence of obstructions to the cloud act to shape and direct it.
Mechanically, the cloud is formed as LNG boils from the surface of the spill. The
evolving vapors are much colder than air and initially form a dense, low-lying cloud. As
the cloud mixes with air and is warmed by its surroundings, it begins to rise. Wind
serves to add a horizontal component to the cloud’s motion. As air mixes with the
natural gas, the mixture becomes flammable (i.e., local compositions are between the
lower and upper flammability limits of LNG). The flammability limits vary with LNG
composition, particularly the proportion of propane. This cloud is then potentially
hazardous to areas beyond the battery limits of the LNG facility.
A number of large-scale tests have demonstrated certain characteristics of LNG vapor
cloud fires. These fires are deflagrations-rapid combustions in which the flame front that
moves through the cloud is preceded by a weak, decoupled shock wave. An
accompanying radiation hazard exists, but not the pressure damage of a shock wave that
occurs when mixtures of other hydrocarbons and air are detonated.
The four requirements for safety – primary containment, secondary containment,
safeguard systems and separation distance – apply across the LNG value chain, from
production, liquefaction and shipping, to storage and re-gasification.
1.5.1. Primary Containment
The first and most important safety requirement for the industry is to contain LNG.
This is accomplished by employing suitable materials for storage tanks and other
equipment, and by appropriate engineering design throughout the value chain.
Integrated NGL Recovery And LNG liquefaction
9
1.5.2. Secondary Containment
This second layer of protection ensures that if leaks or spills occur, the LNG can be
contained and isolated. For onshore installations dikes and berms surround liquid
storage tanks to capture the product in case of a spill. In some installations a
reinforced concrete tank surrounds the inner tank that normally holds the LNG.
Secondary containment systems are designed to exceed the volume of the storage
tank. As will be explained later, double and full containment systems for onshore
storage tanks can eliminate the need for dikes.
1.5.3. Safeguard Systems
In the third layer of protection, the goal is to minimize the release of LNG and
mitigate the effects of a release. For this level of safety protection, LNG operations
use systems such as gas, liquid and fire detection to rapidly identify any breach in
containment and remote and automatic shut off systems to minimize leaks and spills
in the case of failures. Operational systems (procedures, training and emergency
response) also help prevent/mitigate hazards. Regular maintenance of these systems
is vital to ensure their reliability.
1.5.4. Separation Distance
Regulations have always required that LNG facilities be sited at a safe distance from
adjacent industrial communities and other public areas. Also, safety zones are
established around LNG ships. The safe distances or exclusion zones are based on
LNG vapour dispersion data, and thermal radiation contours and other considerations
as specified in regulations.
Integrated NGL Recovery And LNG liquefaction
10
1.6. Markets
1.6.1. Global Markets Historically, world natural gas reserves have generally trended upward. As of
January 1, 2009, proved world natural gas reserves were estimated at 6,254 trillion
cubic feet, 69 trillion cubic feet higher than the estimate of 6,186 trillion cubic feet
for 2008.
The share of LNG in global gas production is increasing. In recent years the share of
LNG in worldwide gas production has grown to 8%, whereas it was still 6% in 2004.
Russia27%
United Arab
Emirates3%
Iran16%
United States4%
Nigeria3%
Others22%
Egypt1%
Qatar14%
Venezuela3%
Algeria3%
Saudi Arabia4%
Figure 4: World Natural Gas Reserves by Country as of January 2009
Integrated NGL Recovery And LNG liquefaction
11
Global LNG market is characterized by excess demand relative to available supplies.
This situation is only expected to aggravate as several countries have made high
investments in LNG trains in the past and now want to wait before increasing
investment, or they have put a stop on export development as domestic demand is
increasing.
The global LNG market is characterised by an overcapacity of regasification
compared to liquefaction. There are 26 existing export, or liquefaction, marine
terminals, located on or off shore, in 15 countries. In contrast, there are 60 existing
import, or regasification, marine terminals, on or off shore, spread across 18 different
countries. In addition to these existing terminals, there are approximately 65
liquefaction marine terminal projects and approximately 181 regasification terminal
projects that have been either proposed or are under construction all around the
world. It is not expected that all of the proposed terminals will be constructed.
Figure 5: Country Share of World LNG Production 2008
Integrated NGL Recovery And LNG liquefaction
12
Countries that Export LNG
Startup date of earliest liquefaction
terminal
Algeria 1971
Australia 1989 Nigeria 1999
Brunei 1972 Norway 2007
Equatorial Guinea 2007 Oman 2000
Egypt 2004 Qatar 1997
Indonesia 1977 Trinidad and Tobago 1999
Libya 1970 United Arab Emirates 1977
Malaysia 1983 United States of America
1969
Countries that Import LNG
Startup date of earliest regasification terminal
Belgium 1987
China 2006 Portugal 2003
Dominican Republic 2003 Puerto Rico 2000
France 1972 South Korea 1986
Greece 2000 Spain 1969
India 2004 Taiwan 1990
Italy 1971 Turkey 1992
Japan 1969 United Kingdom 2005
Mexico 2006 United States of America
1971
Table 3: LNG Exporting Countries and Startup date of earliest Liquefaction terminals
Table 4: LNG Importing Countries and Startup date of earliest Regasification terminals
Integrated NGL Recovery And LNG liquefaction
13
1.6.2. Local Markets
Egypt's proven natural gas reserves have reached 76 trillion cubic feet. Gas exports
during 2008/09 have contributed some $3.3 billion. Thirty per cent of gas production
is exported while the remaining 70 per cent is consumed domestically. Electricity
production, industry and petrochemicals are the three sectors that receive the lion's
share of almost 85 % of the locally consumed gas.
Currently, there are two LNG projects in Egypt at an advanced stage:
i. Idku (Egyptian LNG, ELNG):
Consists of two trains with a capacity of 3.6 mtpa each. The first train was first
operated by the third quarter 2005 with exports to Gaz de France under a 20-year
contract signed in 2002, whereas the second train is has came on stream at 2006
supplied LNG to Lake Charles, Louisiana, US. The project is tied into natural
gas reserves from BG’s Simian/Sienna offshore fields. A third train may be built
by The Malaysian Company Petronas is partner in the project, after buying
Edison’s stake.
ii. Damietta (SEGAS LNG):
The other project, Damietta, is built by the Spanish power group, Union Fenosa.
In 2002, Eni became involved in the project after it purchased a 50% stake in
Union Fenosa’s gas business. The $1.3 billion LNG plant was completed at end
of 2004. Initial capacity of the first train is 4.8 mtpa. Unlike other LNG projects,
this one is not tied to upstream gas development Instead, Union Fenosa has
signed a 25-year gas supply contract with EGPC. Union Fenosa will take 60%
(2.9 mtpa) of SEGAS LNG.
Integrated NGL Recovery And LNG liquefaction
14
1.6.3. Cost
LNG is one of the fastest-growing energy markets. But although there has been
movement towards a global reference price, the costs involved along the value chain
suggest the commoditization achieved in the oil sector is unlikely.
1.6.3.1. LNG value Chain
The LNG value chain represents $7 to $14 billion dollars of investment from
start to finish.
I
Exploration & Production Liquefaction Transport Regasification Sales
Figure 7: LNG Value Chain
Figure 6: LNG Projects in Egypt
Integrated NGL Recovery And LNG liquefaction
15
Investment costs within the five stages vary significantly with the largest share
required by the liquefaction project. Exploration and production account for 15-20%
of the total costs of the LNG value chain; liquefaction for 30-45%; shipping for 10-
30%; and regasification for 15-25%.
1.6.3.2. Linkage between markets
Two indicators suggest the market is moving towards a global reference price:
Geographical connections: since 1970, LNG trading has evolved regionally, in the
Atlantic and Pacific basins, with hardly any interaction between the two markets.
But recently, links between the regions have grown as a result of variations in
demand and supply.
Oil-price indexation: the price of imported gas, whether by pipeline or as LNG, has
traditionally been linked to competing fuels in importing countries. For example,
contracts in Japan are indexed to the Japanese Crude Cocktail (JCC) and in Europe
to fuel oil and gasoil, which are the principal substitute fuels for gas main use in
those markets (power and heat generation).
1.6.3.3. LNG Prices
The average global price of LNG at 2009 was $11/MMBTU.
1.6.3.4. NGL Prices
Global NGL components average prices at 2009:
• Propane: $53 per barrel • Butane: $77.63 per barrel • Pentane: $101.95 per barrel
Integrated NGL Recovery And LNG liquefaction
16
2. Natural gas processing from well till production of LNG
A typical LNG process, where natural gas is first extracted and transported to processing
plants, then purified by removing condensates such as water, oil, mud, as well as other gases
like CO2 and H
2S and sometimes mercury by amine treatment. Afterwards, gas heavies are
removed, before it is cooled down in stages until it is liquefied. LNG is finally stored in
storage tanks and can be loaded and shipped to its end-user destination, where finally
regasification of liquefied gas occurs before usage.
In the next sections of this document, we will handle the technical information about the
liquefaction plant with large emphasis on the integration of natural gas liquids recovery and
liquefaction parts of the process. However, brief information will be given on the rest of the
process, along with some information about LNG storage, tankers, and regasification. Then
a technology for our project will be proposed in the final section.
Figure 8: LNG process
Integrated NGL Recovery And LNG liquefaction
17
3. Pre-treatment of Natural Gas
Natural gas is produced at the well site in compositions of considerable variety; therefore,
natural gas is essentially pretreated before liquefaction to avoid varying problems during
production and transportation, such as the following:
Water: Condensed water forms solid hydrates with hydrocarbons or hydrogen sulfide, or in
addition leads to liquid slugs in pipelines and to corrosion.
Hydrogen Sulfide: Hydrogen sulfide together with free water can cause corrosion,
particularly stress corrosion and hydrogen-induced cracking. Removal of hydrogen sulfide is
performed almost exclusively in centralized treatment plants.
Carbon Dioxide: Carbon dioxide together with free water causes pitting corrosion in carbon
and low-alloy steels. Some natural gases that contain significant amounts of CO2 must be
treated to increase the methane concentration prior to sales.
Sulfur: Gases containing hydrogen sulfide can also contain elementary sulfur as vapor.
Some gas fields, primarily in Canada, Germany, and the United States, contain such high
quantities that the sulfur, depending on pressure, temperature, and gas composition, can
precipitate and plug the production pipe, which then becomes blocked. Furthermore,
elemental sulfur and free water are corrosive.
Mercury: Natural gas can contain mercury in concentrations up to several milligrams per
cubic meter, the bulk of which exists in elemental form. Separated liquid mercury causes
mercury-induced corrosion in pipes and fittings, corrosion damage to aluminum heat
exchangers in cryogenic plants, and damage to measuring and control valves containing
nonferrous metals by amalgam formation. Mercury must also be removed because of its
toxicity.
Integrated NGL Recovery And LNG liquefaction
18
3.1. Objectives of Natural Gas Treating
Two objectives must be met in treating natural gas:
• Adjustment to the required quality standards
• Recovery of by products
The main objective worldwide is production of a sales gas of pipeline standard. In
this respect, both the extent of removal of undesirable components and the range of
conditioning measures are predetermined.
Natural gas treating can take place both directly at the well and in centralized plants.
Treating at the well is always necessary when the gas cannot be transported to a
processing plant by pipeline without hazard. To avoid corrosion, sour gas is often
dehydrated at the well so that free water can no longer condense in the pipeline. The
recovery of sulfur and the separation of nitrogen, carbon dioxide, or helium are
carried out in centralized plants, to which streams of different wells are fed. The
same holds true for liquefaction of natural gas, recovery of LPG, and removal of
higher hydrocarbons.
3.2. Sweetening
Many natural gases contain hydrogen sulfide (H2S) in concentration ranging from
barely detectable quantities to over 30 mole percent. Gases containing H2S or CO2 are
classified as sour, and gases free from H2S and CO2 are called sweet. With increasing
demands to natural gas, natural gases containing H2S are also being tapped for
utilization after purification. Natural gas that is transported to the fuel market must
meet legal requirements, which specify a maximum H2S content less than 4 ppm in
the gas.
Integrated NGL Recovery And LNG liquefaction
19
Many chemical processes are available for sweetening natural gas. At present, the
amine process, is the most widely used method for H2S removal. The process is
summarized in one reaction:
2 RNH2 + H2S → (RNH3)2S
Where:
R = mono, di, or tri-ethanol, N = nitrogen, H = hydrogen, S = sulfur.
Figure 9: Flow diagram of the amine process for gas sweetening
The recovered hydrogen sulfide gas stream may be: (1) vented, (2) flared in waste
gas flares or modern smokeless flares, (3) incinerated, or (4) utilized for the
production of elemental sulfur or sulfuric acid.
If the recovered H2S gas stream is not to be utilized as a feedstock for commercial
applications, the gas is usually passed to a tail gas incinerator in which the H2S is
oxidized to SO2 and is then passed to the atmosphere out a stack.
Integrated NGL Recovery And LNG liquefaction
20
3.3. Dehydration
Dehydration of natural gas is the removal of the water that is associated with natural
gases in vapor form.
The natural gas industry has recognized that dehydration is necessary to ensure
smooth operation of gas transmission lines. Dehydration prevents the formation of
gas hydrates and reduces corrosion. Unless gases are dehydrated, liquid water may
condense in pipelines and accumulate at low points along the line, reducing its flow
capacity. Several methods have been developed to dehydrate gases on an industrial
scale.
The three major methods of dehydration are:
1. Direct cooling (Cryogenic)
2. Absorption.
3. Adsorption.
3.3.1 Cryogenic Dehydration
To decrease the higher hydrocarbon content in addition to maintaining a specific
water dew point, cryogenic dehydration of natural gas is often employed.
The wet gas is cooled until the components to be removed precipitate by
condensation or formation of hydrates. Methanol, glycol, or a paraffin solvent is
often also injected. The reduction in temperature can be achieved by Joule–Thomson
expansion. This route is employed particularly in the first phase of production in
high-pressure wells. When the production pressure is close to that of the
transportation system, external cryogenic units are used.
Integrated NGL Recovery And LNG liquefaction
21
a) High pressure separator (free water knockout); b) Heater; c) Air cooler; d) Separator; e) Joule –
Thomson valve; f ) Gas-gas heat exchanger; g) External cooling system for low-pressure wells
Figure 10: Dehydration with a hydrate inhibitor and cooling at a high-pressure well
3.3.2 Dehydration by Absorption Processes
Standardized dehydration plants using glycol absorption are employed most widely.
Triethylene glycol (TEG) is used in preference to other glycols (mono- and
diethylene glycols) because of its high absorption capacity for water vapor, its low
vapor pressure (small losses from evaporation), and its high thermal stability. This
type of dehydration plant is shown in Figure 11.
a) Well head; b) Corrosion inhibitor – sulfur solvent injection pump; c) High-pressure separator (free
water knockout); d) Heater; e) Flow control valve; f ) Air cooler; g ) Separator; h) Glycol absorber; i)
Demister; j) Glycol – gas heat exchanger; k) Glycol pump; l) Glycol reboiler; m) High-concentration
stripper; n) Glycol storage tank; o) Glycol stripper; p) Water – solvent stripper; q ) Glycol filter; r)
Produced liquids storage tank; s) Flare
Figure 11: Glycol dehydration
Integrated NGL Recovery And LNG liquefaction
22
3.3.3 Adsorptive Dehydration
In adsorptive dehydration the gas is brought in contact with molecular sieves, silica
gel, or Sorbead (i.e., Na2O containing SiO2). Plants with only two adsorbers,
working alternately, are possible. Dew points < −70°C are attainable with adsorption
plants. This is particularly necessary for cryogenic plants and LNG plants, where
traces of water and carbon dioxide can lead to blockage by ice formation.
For regeneration, 5% purge gas is drawn from the main gas flow and fed through the
laden adsorber at plant pressure and 200–330°C. Removed water vapor from purging
of the fixed bed is condensed so that the purge gas, which is at plant pressure, can be
recycled. Regeneration by depressurization is seldom employed in natural gas
treating.
a) – c) Adsorbers; d) Heater; e) Cooler; f ) Chiller; g) Separator; h) Phase separator
Figure 12: Hydrocarbon removal with adsorption and regeneration under pressure
Integrated NGL Recovery And LNG liquefaction
23
Under the normal requirements of natural gas treating dehydration units of this type
are economically less attractive than glycol and cryogenic dehydration plants
described above. However, they are nevertheless employed when, in addition to
simply removing water, adjustment to a specific hydrocarbon dew point is required,
removal of hydrogen sulfide or carbon dioxide is necessary, or an extremely low dew
point is required.
3.4. Removal of Mercury
Natural gas from reservoirs often contains mercury in vapor and/or aerosol form.
Mercury has not resulted in any problems in production from sour gas fields. To
avoid health hazards during treatment and use, the mercury content is lowered in
separate mercury-removal plants from 5 mg/m3 to < 10 µg/m3.
A considerable portion of the mercury has often already been removed by low-
temperature separation (LTS) in the dehydration unit at the well. Mercury levels of <
5 µg/m3 are attained in downstream chemisorption fixed-bed reactors with, for
example, sulfur-impregnated activated carbon. Condensable components, such as
water or hydrocarbons, reduce the loading ability for mercury or even deactivate the
adsorbent. The reactors are not regenerated; rather, the laden adsorbent is fed to an
external treatment plant. Regenerative amalgamation processes are currently being
tested.
Integrated NGL Recovery And LNG liquefaction
24
4. Available Technologies for LNG-NGL Production
4.1. Traditional Stand-Alone Gas Plant Upstream of Liquefaction Plant
A number of NGL recovery processes have been developed for natural gas and other
gas streams. Among various NGL recovery processes, the cryogenic expansion
process has become the preferred process for deep hydrocarbon liquid recovery from
natural gas streams.
In the conventional turbo-expander process, feed gas at elevated pressure is pretreated
for removal of acid gases, water, mercury and other contaminants to produce a
purified gas suitable for cryogenic temperatures. The treated gas is typically partially
condensed utilizing heat exchange with other process streams and/or external propane
refrigeration, depending upon the gas composition. The resulting condensed liquid,
containing the less volatile components, is then separated and fed to a medium or low-
pressure fractionation column for recovery of the heavy hydrocarbon components.
The remaining non-condensed vapor, containing the more volatile components, is
expanded to the lower pressure of the column using a turbo expander, resulting in
further cooling and additional liquid condensation. With the expander discharge
Figure 13: Block diagram for typical NGL extraction plant
Integrated NGL Recovery And LNG liquefaction
25
pressure essentially the same as the column pressure, the resulting two-phase stream
is fed to the top section of the fractionation column. The cold liquid portion acts as
reflux, enhancing recovery of heavier hydrocarbon components. The vapor portion
combines with the gas in the overhead of the column. The combined gas exits the
column overhead as a residue gas. After recovery of available refrigeration, the
residue gas is then recompressed to a higher pressure, suitable for pipeline delivery or
for LNG liquefaction.
4.2. Process Schemes for LNG Train in the Downstream of a Liquefaction Plant
Because LNG liquefaction requires a significant amount of refrigeration energy, the
refrigeration system(s) represent a large portion of a LNG facility. A number of
liquefaction processes have been developed with the differences mainly residing on
the type of refrigeration cycles employed.
The technology selection of LNG process will mainly based on:
• Technical consideration includes process and equipment experience,
reliability, process efficiency, site conditions and environmental impact.
• Economic issues include capital cost, operating cost and lifecycle costing.
• Technical risks associated with a process relate to the track record of the
process in operation.
• Other selections include deciding heating and cooling medium, compressors
and drivers and equipments.
Integrated NGL Recovery And LNG liquefaction
26
4.2.1 The Most Commonly Utilized LNG Technologies:
4.2.1.1 APCI Propane pre-cooled mixed refrigerant process
APCI accounts for about 81% of the world’s base load LNG production capacity.
This mixed refrigerant process provides an efficient process utilizing a multi-
component mixture of hydrocarbons typically comprising propane, ethane,
methane, and optionally other light components in one cycle. A large spiral
wound exchanger is utilized for the majority of heat transfer area. Two main
refrigerant cycles are used in this process:
i.
It uses propane at four different pressure level and cool process gas to -40 0C
& also partially liquefies the MR.
Propane Precooling cycle:
ii.
It is used in main cryogenic exchanger(MCHE) & the partially liquefied
refrigerant is separated into vapour and liquid and sub-cool the process
stream form -35 0C to -160 0C.
Mixed refrigerant liquefaction and sub-cooling cycle:
Figure 14: Flow diagram for APCI Propane pre-cooled mixed refrigerant
Integrated NGL Recovery And LNG liquefaction
27
4.2.1.2 CoP LNGSM Process
This process, formerly known as the Phillips Optimized Cascade LNG Process,
utilizes essentially pure refrigerant components in an integrated cascade
arrangement. The process offers high efficiency and reliability. Also it easily
shifted from LNG recovery to LPG recovery to ethane recovery. Brazed
aluminum exchangers are largely used for heat transfer area, providing for a
robust facility that is easy to operate and maintain. Refrigerants typically
employed are propane, ethylene and methane.
Figure 15: Flow diagram for Phillips Optimized Cascade Process
Integrated NGL Recovery And LNG liquefaction
28
4.3. Integrated NGL and LNG Plants
4.3.1 Introduction
A block diagram for an integrated LNG and NGL process is presented in the below
figure in which its the simplest embodiment of NGL integration, where the Heavies
Removal Column is not refluxed other than with condensed liquids contained within
the column feed.
NGL recovery integration not only reduces capital investment through reutilizing
essentially all equipment in the NGL facility for LNG production, but also improves
overall thermodynamic efficiency. There are significant advantages in the following
aspects:
• The overall integrated process reduces combined capital and operating costs.
• The integrated process reduces combined CO2 and NOX emissions by
improving the thermodynamic efficiency of the overall process.
• Higher recovery of propane (and ethane) is achievable.
• Most NGL process equipment is already utilized in LNG liquefaction plants.
Figure 16: Block diagram showing the integrated NGL and LNG process
Integrated NGL Recovery And LNG liquefaction
29
4.3.2 Available Techniques
Some techniques for the integration between NGL and LNG are available, however,
we focused on two main techniques that are currently established in industry, one
owned by ConocoPhillips Company and the other by Flour Technologies
Corporation, and we will simply describe each technology with its new
modifications.
4.3.2.1 LNG Facility with Integrated NGL Extraction Technology for Enhanced NGL Recovery and Product Flexibility 1
A process for efficiently operating a natural gas liquefaction system with
integrated heavies removal/natural gas liquids recovery to produce liquefied
natural gas (LNG) and natural gas liquids (NGL) products varying
characteristics, such as, for example higher heating value or propane content.
Resulting LNG and NGL products are capable of meeting the significantly
different specifications of two or more markets.
A liquefaction methodology that is preferably applicable to one or more of the
following embodiments of the present technology employs three refrigeration
cycles in which the first 2 cycles use propane and ethane respectively, while an
open methane cycle is employed for the final refrigeration cycle wherein a
pressurized LNG-bearing stream is flashed and the flash vapors are subsequently
employed as cooling agents, recompressed, cooled, combined with the processed
natural gas feed stream, and liquefied, thereby producing the pressurized LNG-
bearing stream.
Next, some configurations for operational flexibility and different products
requirements are shown.
1 Patent owned by ConocoPhilips Company under a publication number of US 2007/0012072
Integrated NGL Recovery And LNG liquefaction
30
• First Configuration
In the following figures we illustrate an embodiment of the LNG facility that can
be operated to maximize C2+ recovery in the final NGL product.
Figure 17 illustrates one embodiment of the heavies removal/LNG recovery
system of the present technology. Lines H, D, B, F, E, and G show how the
liquefaction section shown in figure 18 is integrated with the heavies
removal/NGL recovery system.
Figure 17: A flow diagram showing integrated heavies removal/NGL recovery system
Integrated NGL Recovery And LNG liquefaction
31
Figure 18: A simplified flow diagram of a cascaded refrigeration process for producing LNG
Integrated NGL Recovery And LNG liquefaction
32
• Second Configuration
In the following figures we illustrate one embodiment of the LNG facility which
can be operated in such a way to maximize propane and heavier component
recovery in the NGL product.
Figure 19 illustrates one embodiment of heavies removal/NGL recovery system.
Lines A, B, and C show how the heavies removal/NGL recovery system is
integrated into the LNG facility.
Figure 19: A flow diagram showing integrated heavies removal/NGL recovery system connected to the LNG facility of Fig 20
Integrated NGL Recovery And LNG liquefaction
33
Figure 20: A simplified flow diagram of a cascaded refrigeration process for producing LNG
Figure 20 illustrates the system in which how we can cool natural gas to its liquefaction
temperature via three mechanical refrigeration stages in combination with an expansion type
cooling section.
Integrated NGL Recovery And LNG liquefaction
34
• Third Configuration
In the following figures we illustrate another embodiment of the LNG facility
capable of operating to maximize C5+ recovery in the NGL product.
Figure 21 it illustrates one embodiment of the heavies removal/LNG recovery system
of the present technology. Lines D, B, F, E, and G show how the liquefaction section
shown in figure 22 is integrated with the heavies removal/NGL recovery system.
Figure 21: A flow diagram showing integrated heavies removal/NGL recovery system
Integrated NGL Recovery And LNG liquefaction
35
Figure 22: A simplified flow diagram of a cascaded refrigeration process for producing LNG
Integrated NGL Recovery And LNG liquefaction
36
4.3.2.2 Intermediate Pressure LNG Refluxed NGL Recovery Process2
Liquefied natural gas (LNG) facility employing an intermediate pressure
distillation column for recovery of ethane and heavier components from the
processed natural gas stream in a way that increases operational stability and
minimizes capital and operating costs.
In the following figure a simplified schematic flow diagram of one embodiment
of an LNG facility that employs an intermediate pressure distillation column,
particularly illustrating the use of heated side draw and a turbo expander that
drives a compressor downstream of the column.
2 Patent owned by ConocoPhilips Company under a publication number of US 2008/0098770
Figure 23: Simplified schematic flow diagram of an LNG facility that employs an intermediate pressure distillation column
Integrated NGL Recovery And LNG liquefaction
37
In the following figure another simplified schematic flow diagram of one
embodiment of an LNG facility that employs an intermediate pressure
distillation column, particularly illustrating the use of a methane rich reflux
and a turbo expander that drives a compressor upstream of the column.
Figure 24: Simplified schematic flow diagram of an LNG facility that employs an intermediate
pressure distillation column.
Integrated NGL Recovery And LNG liquefaction
38
Figure 25: A schematic of one exemplary plant configuration using a twin column configuration for production of cold compressed overhead product and separation of C2 and C3.
4.3.2.3 Configurations and Methods of Integrated NGL Recovery and LNG Liquefaction3
Contemplated plants include a NGL recovery portion and a LNG liquefaction
portion, wherein the NGL recovery portion provides a low temperatures and high
pressure overhead product directly to the LNG liquefaction portion. Feed gas
cooling and condensation are most preferably performed using 3 refrigeration
cycles that employ refrigerants other than the demethanizer/absorber overhead
product. Thus, cold demethanizer/absorber overhead product is compressed with
the turbo expander and delivered to a liquefaction portion at significantly lower
temperature and higher pressure without net compression energy expenditure.
The present technology is directed to configurations, plants, and methods for
natural gas processing and liquefaction in which a cold separator overhead
product is directly compressed in a compressor that is driven by a feed gas vapor
expander, and wherein the compressed cold separator overhead product is then
3 Patent owned by Fluor Technologies Corporation under a publication number of US 2007/0157663
Integrated NGL Recovery And LNG liquefaction
39
Figure 26: A more detailed schematic of an exemplary plant according to figure 2.1-1 with two cascade refrigeration cycles and one mixed refrigerant cycles for NGL recovery and
LNG liquefaction.
liquefied in a liquefaction unit. Most advantageously, such plants integrate NGL
processing and LNG liquefaction in an efficient, cost effective, and technically
simple manner, specifically when feed gas pressure is higher than 800 psi.
It should be appreciated that contemplated configuration and methods allow for
an integrated NGL recovery and LNG liquefaction process in which 99%
propane and up to 85% ethane can be recovered from a natural gas feed.
Integrated NGL Recovery And LNG liquefaction
40
Figure 27: A schematic flow diagram of an exemplary plant configuration
4.3.2.4 Integrated NGL Recovery and LNG Liquefaction4
Contemplated plants include a refluxed absorber is operated at a higher
pressure than the distillation column to thereby produce a cryogenic
pressurized lean gas. The lean gas is further compressed to a pressure
suitable for liquefaction using energy from feed gas vapor expansion.
Desired separation of C2 products is ensured by temperature control of the
absorber and distillation column using flow ratios of various streams within
the plant, and by dividing the separation process into two portions at
different pressures.
4 Patent owned by Fluor Technologies Corporation under a publication number of US 2008/0271480
Integrated NGL Recovery And LNG liquefaction
41
The present technology is directed to configurations and methods of NGL
recovery when coupled to an LNG liquefaction process, in which recovery of
C2 components can be adjusted using flow ratios of selected process streams.
Most preferably, the absorber in such configurations and methods is operated
at significantly higher pressure than the distillation column provide a
cryogenic pressurized gas, while the absorber and distillation column
temperatures are adjusted to such that desired quantities of C2 and C3+
products are recovered in the NGL. Cryogenic absorber overhead product is
then compressed to a pressure suitable for liquefaction using energy derived
from expansion of a vapor portion of the feed gas which is expected to have
pressure higher than 800 psi.
5. Storage & Transportation
5.1. Storage
Once the gas becomes liquid, it flows into large insulated storage tanks. This storage
tank is a specialized type of storage tank which can keep the LNG at low temperature
of -162°C. The temperature within the tank will remain constant if the pressure is kept
constant by allowing the boil off gas to escape from the tank. This is known as auto-
refrigeration.
LNG storage tanks have double containers, where the inner contains LNG and the
outer container contains insulation materials. The most common tank type is the full
containment tank. Tanks are roughly 180 feet high and 250 feet in diameter.
Cylindrical tanks with formed heads are the most widely used tanks for storing LNG.
Also NGL are stored in the same type of tanks, but when in gaseous form, pressure
vessels, most commonly spherical tanks are the most appropriate. As the requirement
came to store ever larger quantities of NGL products, the pressure storage option
Integrated NGL Recovery And LNG liquefaction
42
became increasingly expensive and unattractive from a practical and safety point of
view, therefore low pressure storage in refrigerated liquid form became the normal for
large quantities.
5.1.1. Methods of Operation in Tanks:
• Single containment tanks: Our single containment tanks typically feature a
primary liquid containment open-top inner tank, a carbon steel primary vapor
containing outer tank and an earthen dike for secondary liquid containment.
• Full containment tanks: Full-containment tanks typically feature a primary
liquid containment open-top inner tank and a concrete outer tank. The outer tank
provides primary vapor containment and secondary liquid containment. In the
unlikely event of a leak, the outer tank contains the liquid and provides
controlled release of the vapor.
5.2. Transportation
Transportation and supply is an important aspect of the gas business, since LNG
reserves are normally quite distant from consumer market.
LNG is transported in specially designed ships with double hulls protecting the cargo
systems from damage or leaks which are called LNG carriers. LNG will be sometimes
taken to cryogenic temperatures to increase the tanker capacity. Recently ship-to-ship
transfer (STS) transfers have been carried out which involved the transfer of LNG
from a conventional LNG carrier to an LNG regasification vessel (LNGR).
A typical modern LNG ship, or LNG carrier, is approximately 300m long, 43m wide
and has a draft of 12m. Cargo capacities range from 1,000 cubic meters up to 267,000
cubic meters. Sailing speeds approach 21 knots.
There are around 151 LNG tankers in the world. Their total capacity is 25.1 million
cubic meters of liquid. The boil-off is used as fuel for the ship’s main propulsion
Integrated NGL Recovery And LNG liquefaction
43
during Sea where the LNG is the only cargo which is permitted to be used as fuel in
this manner.
Figure 28: LNG Ship Types
Figure 29: Cross Section of LNG Tanker
Integrated NGL Recovery And LNG liquefaction
44
6. Regasification
Regasification of the stored LNG is the final setup in the operation of LNG process, it’s
simpler than liquification, and it is purely physical and not chemical. The regasification is
accomplished by addition of heat from ambient air, ambient water, or remote fired
vaporizers. The Cost of regasification system generally represents only a small fraction of
the cost of the storage plant; however, reliability of the system is most important because
failure or breakdown would defeat the purpose of the facility. Assuming LNG to be pure
methane, the energy required to gasify the liquid is almost 40% of the gross heating value.
Figure is a simplified flow diagram of a typical LNG regasification system. Liquid is
pumped from the storage container to the vaporizer. The pump discharge pressure must be
high enough to provide the desired gas pressure for entry into the transmission or
distribution system. Heat is added to vaporize the high pressure LNG and to superheat the
gas. Gas leaving the vaporizer must be odorized because the liquefaction process removes
any odorant originally in the gas.
Figure 30: Simplified flow diagram of a typical LNG regasification system.
Integrated NGL Recovery And LNG liquefaction
45
7. Proposed technology
Figure 31: proposed technology process flow diagram
Integrated NGL Recovery And LNG liquefaction
46
7.1. Precooling of feed gas
Contaminants-free and dried feed gas stream enters the plant at about 800 psig and
120° F, and is precooled in exchanger 51 to typically 10° F to -30° F, forming stream
2, using multiple cooling streams including liquid stream 5 from separator 52, side
reboiler stream 22 from demethanizer 61, flash vapor 70 from LNG storage tank 69,
external refrigerant 74, and letdown absorber bottoms stream 15.
The chilled feed gas stream 2 is separated in separator 52, forming a gaseous portion
3 and a liquid portion 4. The liquid portion 4 is letdown in pressure in JT valve 53
forming stream 5, and optionally heated to stream 6 with the heat content from the
feed gas prior to entering the demethanizer 61. The gaseous portion 3 from separator
52 is split into two portions. One portion (stream 7) is routed to the exchanger 54 to
provide reflux to the absorber, and the other portion (stream 8) is expanded in turbo-
expander 64 to produce a chilled vapor stream 10, typically at -80° F to -100° F and
to generate power to drive the residue gas compressor 65.
7.2. Separation of C2+ from feed gas
The chilled vapor 10 is fed to absorber 58 (which act as a C1/C2+ separator), which
operates at a pressure well above 450 psig, typically at between 500 psig to 700 psig,
and most typically at 600 psig. Absorber 58 is refluxed with two cold streams,
wherein the first reflux (top reflux) is supplied by stream 11 (via 56 and 27) from the
demethanizer 61, wherein the second reflux is supplied by stream 12 (via 9 and 55)
from exchanger 54. The reflux streams are chilled to about -125° F to -155° F. Using
twin reflux streams and suitable flow ratios between streams 7 and 8; high C3
recovery can be maintained for the various levels of ethane recovery. The absorber
produces an overhead vapor stream 28 (mainly methane) at about -100° F to -110° F
and a bottoms stream 14 (mainly C2+) at about -90° F to -100° F.
Integrated NGL Recovery And LNG liquefaction
47
A portion of the absorber bottoms stream 14 is letdown in pressure in JT valve 59 to
about 460 psig, and is chilled to about -100° F, forming stream 15. During C3
recovery, this cold stream is used to provide at least a portion of the cooling duty of
feed exchanger 51 and the reflux duty in condenser 62 to form streams 17 and 18,
respectively.
During C2 recovery, at least a portion of absorber bottom stream 14 is routed directly
to the top of the demethanizer. In this operation, JT valve 59 is partially, and more
typically entirely closed and JT valve 60 is partially, and more typically entirely open
forming stream 20 at a pressure that is about 50-350 psig less than absorber pressure.
This stream enters the demethanizer at a temperature of between about -90° F to -130°
F. The demethanizer is reboiled using reboiler 201 and produces bottom product 25,
which is then fed to deethanizer 62. Demethanizer overhead product 24 is then routed
back to the absorber as reflux stream 11. To that end, the overhead product 24 is re-
compressed to form stream 26 (to a pressure above absorber pressure) by compressor
66 and chilled in exchanger 54 to form stream 27, which is expanded to reflux stream
11.
7.3. Liquefaction unit
The overhead vapor from the absorber is compressed by residue gas compressor 65
using power generated by turbo expander 64 forming a discharge stream 29, typically
at about 900 psig and -70° F to -80° F. The residue gas is chilled and condensed in
exchanger 67 to about -255° F to -265° F using refrigerant 79 operating at -180° F to -
270° F that is produced by the mixed refrigeration system 102, after the compressed
stream 76 is chilled in exchangers 54, 67, and JT’d via valve 92. The liquefied residue
gas is further letdown in pressure to stream 82 at about 16.0 psig via JT valve 90, and
the flashed liquid is stored in LNG storage tank 69. LNG product is withdrawn as
stream 30 and withdrawn to storage or transport.
Integrated NGL Recovery And LNG liquefaction
48
In some cases, depending on the natural gas composition and the temperature from
the liquefier exchanger, a significant quantity of light gas 70 is evolved which can be
recovered as fuel gas after its refrigerant content is recovered. Where desired, a
portion of the ethane product stream 15 can be directed from deethanizer 59 to LNG
storage or transport. In this way, lean LNG can be converted to a heavier and richer
LNG.
7.4. C2 liquid recovery
Deethanizer 62 is configured as reboiled column using reboiler 202 to separate C2
from C3+ components, wherein the C3+ components are drawn from the column as
stream 23. The C2 overhead product is condensed in overhead condenser 302 and
separated in drum 402. One portion 18 of the C2 product is pumped back by pump 59
to the column as reflux while another portion 19 is withdrawn for LNG blending or
storage/transport via stream 17.
7.5. C3 liquid recovery
Depropanizer 63 is configured as reboiled column using reboiler 203 to separate C3
from C4+ components, wherein the C4+ components are drawn from the column as
stream 47. The C2 overhead product is condensed in overhead condenser 303 and
separated in drum 403. One portion 45 of the C3 product is pumped back to the
column as reflux while another portion 46 is withdrawn as a final product.
7.6. C4 liquid recovery
Similarly, Debutanizer 64 is configured as reboiled column using reboiler 204 to
separate C4 from C5+ components, wherein the C5+ components are drawn from the
column as stream 57 as a final product or it can be further processed. The C2 overhead
Integrated NGL Recovery And LNG liquefaction
49
product is condensed in overhead condenser 304 and separated in drum 404. One
portion 49 of the C4 product is pumped back to the column as reflux while another
portion 50 is withdrawn as a final product.
7.7. Refrigeration cycles
Three temperature ranges are provided by two vaporizing refrigeration cycles, A first
temperature range of 10° F to -35° F refrigeration for the feed gas pre-cooling, a
second temperature range of -60° F to -160° F for absorber reflux, and a third
temperature range of -180° F to -270° F for gas liquefaction. It is generally preferred
that the refrigerant in contemplated refrigeration circuits comprise one, two, or more
hydrocarbon components and may further include nitrogen, halocarbons, and/or other
refrigerants.
Contemplated refrigeration cycles may also include combinations of refrigeration
cycles, and especially combinations of multicomponent mixed refrigerant cycles, and
single component cascade cycles. Other preferred refrigeration cycles include letdown
devices such as turbo-expanders and Joule Thomson valves. With respect to the
temperature levels, (combination of) refrigeration cycles, and cooling media, it should
be noted that they may be adjusted as needed to achieve the lowest energy
consumption in the cooling and liquefaction processes.