Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Manufacturer of Christie Glasshouses and Sheds
INSTRUCTIONS FOR ASSEMBLY
1585mm x 3125mm Jumbo Workshop
1 Thomas Burns Street, Dunedin
Phone (03) 477 7909 www.allans.co.nz
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Congratulations on your purchase of a quality Christie shed. All the parts
required for building your shed are included in the pack you received.
Optional extras include:
• Concrete base fixing brackets
• Timber frame to concrete pad fixing brackets
• Shelving brackets
• Free standing shelving
You will need the following to complete the shed assembly:
• Hammer
• Level
• Tape measure
• Pozi-drive screwdriver
• 8mm Spanner
Begin with the base. This can be concrete or timber.
On clear and level ground build the OUTSIDE of the base to the required
size. This MUST be SQUARE and LEVEL.
Timber Base: Peg the timber frame to ground. Include extra bearers if
using a slat floor (as per the picture above).
Concrete base: Include a 1500mm long step to sit directly underneath the
door guide as per the dimensions shown.
Note corner orientation
for timber frame Timber Base
Concrete Base
Concrete step
2
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Starting in one corner, place one of the Rear Walls and the Left Wall on the
base, with the corners overlapping.
Line up the holes in the corners of the two panels and bolt together. There
are four bolts per corner. Overlap the corners so that the panel edges are not
visible from the front of the shed.
Rear Wall
Wall inside face
Base
Front
Left Wall Right
Wall
Panel edge facing
away from front
Panel edge facing
away from front
Rear Wall Left Wall
VIEW FROM TOP
3
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Repeat the process for the other Rear Wall and Right Wall.
Start by overlapping the two panels at the bottom, pushing them together
until the cappings butt up against each other without a gap. Use a 4” nail or
nail punch through one set of bolt holes to pull the panels into alignment
and bolt through the other set of holes. Remove the nail/nail punch and bolt
through the other set of holes.
Overlap the corners of the Rear Wall and Right Wall and bolt together.
Right
Wall
Rear Wall Bolt overlapping edges
This panel sits on
outside of other panel
Use 4” nail to align holes in Rear Walls if necessary
VIEW FROM REAR Cappings sit flush against each
other at top and bottom of panels
4
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Bolt the Left Hand and Right Hand Fronts to the Walls.
Join the Left Hand Front and Right Hand Front together with the Door
Lintle at the top.
Left Hand Front
Right Hand Front
5
Door Lintle
Door Lintle
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Attach the Door Guide at the bottom of Left Hand and Right Hand Front
panels. Ensure the doors sit within the guide as shown, and attach the Door
Guide at the ends.
Place the four Roof Panels on the top, overlapping each panel and bolting
them together. Bolt through the Roof Panels at the front and rear of the
shed. Attach the Roof Capping at the front and Spouting to the rear as
shown.
Door Guide
Door
Bolt at both ends
6
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Assemble the Doors by sliding the wheels at the top of each Door into the
Door Rails. Ensure the Doors are assembled such that the handles meet in
the middle when the Doors are fully closed. Fasten a bolt and nut in four
places in the Door Rail as shown to act as a Door Stop and limit the door
movement.
Front Spouting to
rear of shed
Rear Wall
Roof Panel
Spouting Roof
Capping
Drop bolts through holes in top first,
then tilt Spouting and tighten. Bolt
bottom afterwards
7
Door Handles
this way
Door Stop positions
Door Stop
Door Rail
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Attach the two side flashings. These fit OVER the roof panel, but INSIDE
the spouting and front flashing. Bolt these through the roof panel, and to
the side of the front flashing.
Concrete Base:
Fix the walls to the base
with the bracket using
appropriate masonry
fasteners.
Flashing fits
OVER roof
panel Flashing fits
INSIDE
spouting
Right
Flashing
Left
Flashing
Fixing
bracket
Base
8
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Timber Base: Hammer a piece of 50mm x 50mm timber to the timber
frame directly under the door opening to strengthen the door guide. Use at
least three self-drilling screws to drill through the top of the door guide into
the 50mm x 50mm timber as shown.
Concrete Base: Drill three holes through the top of the Door Guide to
expose the concrete step. Use suitable masonry fasteners, such as
dynabolts, to attach the Door Guide to the Concrete Base.
50mm x 50mm timber Door guide
50mm x 50mm timber
Door
Self-drilling screw
Timber
frame
Door guide
Concrete Base
Door Masonry fastener
9
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Timber Base: Nail the shed to the timber base.
Nail all panels to timber
10
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Timber Base on Existing Concrete Pad: Fix brackets to timber. Fix
brackets to existing concrete with suitable masonry fasteners.
Fix bracket to timber
Fix bracket to concrete
11
F:\C - E\Christie Garden Products\Sheds\Shed 1585 x 3125 Jumbo Workshop\Shed 1585 x 3125 Jumbo Workshop
Assembly Instructions Rev 3.docx
Timber Base: Nail floor slats to the timber base.
Your Christie Shed is now complete and ready for years of service.
Full warranty terms and conditions available by visiting www.allans.co.nz
12
Front
VIEW FROM TOP
Floor slats sit this way
Right
Wall
Left
Wall