Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
NJT8103 series Instruction Manual Page 1
Copyright © 2017, New Japan Radio Co., Ltd. All rights reserved.This instruction manual may not be reproduced, in part or in whole,
without the permission of New Japan Radio Co., Ltd.
The specifications and information regarding the products in thisinstruction manual are subject to change without notice.All statements, information, and recommendations in this
instruction manual are believed to be accurate but are presentedwithout warranty of any kind, express, or implied.
Users must take full responsibility for their application of anyproducts.
Instruction Manualfor
Document Part Number: IM-T8103
Revision: 01
IM-T8103 Rev.01
[NJT8103 series]C-band 3W BUC
Issue Date: July 27, 2017
NJT8103 series Instruction Manual Page 2
1.
2.
3.
4.
5.
IM-T8103 Rev.01
NJRC strives to produce reliable and high quality microwave components.NJRC's microwave components are intended for specific applications andrequire proper maintenance and handling. To enhance the performanceand service of NJRC's microwave components, the devices, machinery orequipment into which they are integrated should undergo preventativemaintenance and inspection at regularly scheduled intervals. Failure toproperly maintain equipment and machinery incorporating these productscan result in catastrophic system failures.
To ensure the highest levels of reliability, NJRC products must always beproperly handled. The introduction of external contaminants (e.g. dust, oilor cosmetics) can result in failures of microwave components.
NJRC offers a variety of microwave components intended for particularapplications. It is important that you select the proper component for yourintended application. You may contact NJRC's sales office or salesrepresentatives, if you are uncertain about the products listed in thecatalog and the specification sheets.
General Caution
Special care is required in designing devices, machinery or equipment,which demand high levels of reliability. This is particularly important whendesigning critical components or systems whose foreseeable failure canresult in situations that could adversely affect health or safety. Indesigning such critical devices, equipment or machinery, carefulconsideration should be given to, amongst other things, their safetydesign, fail-safe design, back-up and redundancy systems, and diffusiondesign.
The products listed in the catalog and specification sheets may not beappropriate for use in certain equipment where reliability is critical orwhere the products may be subjected to extreme conditions. You shouldconsult our sales office or sales representatives before using the productsin any of the following types of equipment.* Aerospace Equipment* Equipment Used in the Deep Sea* Power Generator Control Equipment (nuclear, steam, hydraulic)* Life Maintenance Medical Equipment* Fire Alarm/Intruder Detector* Vehicle Control Equipment (automobile, airplane, railroad, ship, etc.)* Various Safety Equipment
NJT8103 series Instruction Manual Page 3
6.
IM-T8103 Rev.01
General Caution (continued)
NJRC's products have been designed and tested to function withincontrolled environmental conditions. Do not use products under conditionsthat deviate from methods or applications specified in the catalog andspecification sheets. Failure to employ NJRC's products in the properapplications can lead to deterioration, destruction or failure of theproducts. NJRC shall not be responsible for any bodily injury, fires oraccidents, property damage or any consequential damages resulting fromthe misuse or misapplication of its products. PRODUCTS ARE SOLDWITHOUT WARRANTY OF ANY OF KIND, EITHER EXPRESS OR IMPLIED,INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OFMERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
NJT8103 series Instruction Manual Page 4
7. Specification ………………………………………………………………………………
This instruction manual describes Standard / Full C-band 3W BUC (Model No.:NJT8103N, NJT8103F, NJT8103WN, and NJT8103WF) herein referred to as "theUnit".
This instruction manual provides information and instructions for installation andoperation of the Unit.
1. Introduction ………………………………………………………………………………
2. Safety Instructions ……………………………………………………………………
5
10
5. Physical Description …………………………………………………………………
Contents
This instruction manual is intended for use by trained field installers or systemengineers responsible for satellite networks.
20 - 21
6. Installing ……………………………………………………………………………………
6 - 9
Updated instruction manual may be available from NJRC's sales [email protected].
IM-T8103 Rev.01
4. Overview ……………………………………………………………………………………
16 - 19
11
12 - 15
About This Instruction Manual
3. Packing List ………………………………………………………………………………
NJT8103 series Instruction Manual Page 5
Numbering System
The Unit has the following line-up:
The Unit receives a reference signal (10 MHz) and an IF signal (L‐band: 950 to1,525 MHz or 950 to 1,825 MHz) input and transmits an RF signal (C‐band: 5.850to 6.425 GHz or 5.850 to 6.725 GHz) output.
The Unit comes in a single, weatherized housing rated for outdoor use. The Unithas either an N-Type or a F-type female connector input, a WR75 waveguideoutput. The Unit is operated by +24 V DC power (Range: +12 to +30 V) input.
This instruction manual is for Standard / Full C-band 3W BUC (Model No.:NJT8103N, NJT8103F, NJT8103WN, and NJT8103WF).
1. Introduction
IM-T8103 Rev.01
NJT8103 series Instruction Manual Page 6
Symbol Description
IM-T8103 Rev.01
2. Safety Instructions
CAUTION
Statement
NOTE is used to notify ofinstallation, operation, ormaintenance information that isimportant, but not hazard-related.
DANGER, WARNING, CAUTION, and NOTE Statements
Use the following safety guidelines to help protect the Unit from potential damageand to help ensure your own personal safety.
WARNING indicates a potentiallyhazardous situation which, if notavoided, could result in death orserious injury.
CAUTION indicates a potentiallyhazardous situation which, if notavoided, could result in minor ormoderate injury. CAUTION mayalso be used to indicate otherunsafe practices or risks ofproperty damage.
NOTE
DANGER DANGER indicates an imminentlyhazardous situation which, if notavoided, will result in death orserious injury.
WARNING
DANGER, WARNING, CAUTION, and NOTE statements are used throughoutthis instruction manual to emphasize important and critical information. Youmust read these statements to help ensure safety and to prevent productdamage. The statement are defined below.
NJT8103 series Instruction Manual Page 7
2.1. Safety Statements
When installing the Unit, observe the following safety guidelines.
3. RF Radiation
1. Opening / Removing
2. Input VoltageOnly input a voltage within the range indicated in specifiedvoltage.DO operate at the input voltage of +12 to +30 V DC power.
A radiation hazard exists if the BUC is operated with its RFsignal output unterminated.DO NOT operate the BUC without a load or terminationattached to the RF signal output.
DO NOT dismantle this product.Dismantlement may cause malfunction and electric shock.
ELECTRIC HAZARD
HOT SURFACE
Symbol DescriptionGENERIC HAZARD
IM-T8103 Rev.01
NJT8103 series Instruction Manual Page 8
DO NOT block the fins.Normally the Unit should be mounted with long fins face up.
2. WeatherproofThe Unit is mounted outdoors must be adequatelyweatherproofed.Ensure the waveguide joints are properly sealed with thesupplied o-ring (gasket).Use self-amalgamating tape to seal connectors and cable entrypoints from the connector to the cable sheath.
Operate the Unit within the ambient temperature range of -40to +60 degree C.
2.2. Instruction Statements
1. Mounting
DO NOT input an IF signal over the range of +13 dBmmaximum and a reference signal within the range of -5 to +5dBm.
DO NOT touch the body, especially fins, during operating theUnit.High touch temperatures may exist, depending on loadconditions.
4. High Temperatures
IM-T8103 Rev.01
6. Operating Temperature.
5. Input Level
NJT8103 series Instruction Manual Page 9
Opening or removing any component (e.g. label, and screws)or sealed area will immediately void the warranty.
DO NOT remove the sealing tape on the waveguide. If thesealing tape is removed, it may lose the performance ofwaterproof.
4. ConnecterConnect the IF cable to the input connector of both N and F-type with 0.68 to 1.13 N·m torque.
5. Warranty
3. Waveguide
IM-T8103 Rev.01
NJT8103 series Instruction Manual Page 10
NJT8103F
3. Packing List
No.
IM-T8103 Rev.01
The Unit is shipped in a single shipping container with the following content:
Qty(1), O-ringQty(1), Hexagon Wrench Key (M4)
NJT8103WN
Qty(8), Spring Washer
1 set
1 sheet
Qty1 unit
Description
Qty(8), Hexagon Socket Head Bolt (#10-32UNF, L=0.5")
ORNJT8103WF
NJT8103N
Date sheet
Accessory of BUC
1.
2.
3.
C-band 3W BUC
NJT8103 series Instruction Manual Page 11
IM-T8103 Rev.01
4. Overview
The unique features are* High Efficiency Output Power P1dB: +34.5 dBm min. over temperature ACPR: -26 dBc @ Pout = +34.5 dBm Power Consumption: 18 W typ. @ No IF Signal 21W typ. 25 W max. @ Pout = +34.5 dBm* RF Frequency Line-up Full C-band: 5.850 to 6.725 GHz Standard C-band: 5.850 to 6.425 GHz* DC Power Operation +12 to +30 VDC* Smaller Size & Lighter Weight Dimension: 135.4 (L) x 85 (W) x 56 (H) mm [5.33” (L) x 3.35” (W) x 2.20” (H)] Weight: 800 g [1.8 lbs]* LED Indicator* RoHS Compliance
The Unit transmits an RF signal (C‐Band: 5.850 to 6.425 GHz or 5.85 to 6.725GHz) output with up to 3W (+34.5 dBm) linear.
Block Diagram
The Unit has the following line-up:
NJT8103 series Instruction Manual Page 12
IM-T8103 Rev.01
5.1. Appearance
5. Physical Description
This section describes appearance and outline for the Unit.
Overall Picture(Model No. NJT8103WF)
NJT8103 series Instruction Manual Page 13
5.2. Outline
5.2.1. Outline Drawing of NJT8103N / NJT8103WN
IM-T8103 Rev.01
NJT8103 series Instruction Manual Page 14
5.2.2. Outline Drawing of NJT8103F / NJT8103WF
IM-T8103 Rev.01
NJT8103 series Instruction Manual Page 15
GroundHole
M4 Threaded Hole Common chassis ground
5.3. Description of Connectors, Switches, and LEDs
IM-T8103 Rev.01
Item DescriptionIF / ReferenceInputandDC Power Input
RF Output
The Unit receives an IF signal (950 to1,525 MHz or 950 to 1,825 MHz) and areference signal (10 MHz) and isrequired to supply +12 to +30 V DCpower via this connector.The Unit transmits an RF signal (5.85to 6.425 GHz or 5.85 to 6.725 GHz) viathis waveguide.
Purpose
WR-75
N-typeORF-typeFemaleConnector
NJT8103 series Instruction Manual Page 16
The Unit can be mounted with OMT or the waveguide filter of the satelliteantenna.
When mounting on the OMT or the waveguide filter, follow the followingcaution:
DO NOT block the fins.Normally the Unit should be mounted with long fins face up.
IM-T8103 Rev.01
When mounting with the OMT or the waveguide filter, follow the followingsteps:
Step 1: Verify that the groove on the waveguide flange of the Unit for theo-ring is clean.Insert the supplied o-ring (gasket) the groove as shown in a figurebelow.
Insaeting O-ring
6. Installing
This section describes basic installation for the Unit.
6.1. Mounting Configuration
NJT8103 series Instruction Manual Page 17
Insaeting O-ring
Table: Screw Length ListFlange Thickness of OMT or Screw Length2 - 5 mm [0.075" - 0.2"] 1/2"
The Unit must be adequately weatherproofed to place inoutdoor.Ensure that the waveguide joint is properly sealed with thesupplied o-ring (gasket).
5 - 8.5 mm [0.2" - 0.325"] 5/8"8.5 - 11.5 mm [0.325" - 3/4"
IM-T8103 Rev.01
Step 2: Secure the OMT or the filter to the Unit using the enclosed hexagonsocket head bolts (#10-32UNF L=0.5") with 2.39 to 2.91 N·mtorque as shown, when the thickness of the flange of the OMT orthe filter is 2.0 to 5.0 mm.When the thickness is not 3.5 to 5.0 mm, you should prepare theappropriate length screws or bolts based on following table.
11.5 - 15 mm [0.45" - 7/8"
NJT8103 series Instruction Manual Page 18
Step 2: Use self-amalgamating tape to seal connector and cable entrypoints from the connector to the cable sheath.
Only input a voltage within the range indicated in specifiedvoltage.DO operate at the input voltage of +12 to +30 V DC power atthe coaxial connecter on the Unit.
DO NOT input an IF signal over the range of +13 dBmmaximum and a reference signal within the range of -5 to +5dBm.
6.2. Connecting ModemThe Unit is connected the modem.
6.2.1. Connecting Coaxical Cable.The Unit receives the reference and the IF signal and is required to supply+12 to +30 V DC power from the modem via coaxial cable.
IM-T8103 Rev.01
When connecting the coaxial cable from the modem, follow the followingsteps:
Step 1: Connect the coaxial cable with the N or F-type male connectorsto the coaxial connecter equipped with the Unit which is shownin a figure below under 0.68 to 1.13 N・m torque.
Location of Coaxial Connector
Supplied the IF/Ref./DC Power via Coaxial Cable
NJT8103 series Instruction Manual Page 19
Fix the ground wire from other equipments to the ground holenear the coaxical connector with enclosed on the Unit which isshown in a figure below.
Location of Ground Wire
To reduce the risk of damage or broken by lightning surge, theUnit should be fixed with the ground wire.
Step 1:
6.2.2. Fixing Ground WireThe Unit should be common with ground of other equipments (e.g.antenna).
Fixing a ground wire from the common ground of other equipments forgrounding is proceed with the following step:
IM-T8103 Rev.01
Fixing the Ground Wire
NJT8103 series Instruction Manual Page 20
Output Frequency Range<Full C-band> 5.850 to 6.725 GHz<Standard C-band> 5.850 to 6.425 GHz
Input Frequency Range<Full C-band> 950 to 1,825 MHz<Standard C-band> 950 to 1,525 MHz
Maximum IF Input Level +13 dBm max.(without damage)Conversion Type Single, fixed L.O.L.O. Frequency 4.90 GHzFrequency Sense PositiveOutput Power @ 1dB G.C.P. +34.5 dBm min. over temperatureLinear Gain 59 dB nom., 53 dB min.
-60 dBc/Hz max. @ 100 Hz-70 dBc/Hz max. @ 1 kHz-80 dBc/Hz max. @ 10 kHz-90 dBc/Hz max. @ 100 kHz-100 dBc/Hz max. @ 1MHz
<N-type Model> 50 ohms nom.<F-type Model> 75 ohms nom.
12.
11.
Item
13. Input VSWR
15.
9.
10.Reference
[Phase Noise]
Input Impedance
Output VSWR 2 : 1 max.14.
Infinite : 11.3 : 1 max.[Recommendation]
-26 dBc typ.
-140 dBc/Hz max. @ 10 kHzL.O. Phase Noise
8.
3.
2.
5.6.7.
7. Specification
No.1.
4.
Specifications
ACPR
The Unit is in compliance with the following specifications:
[Non Damage]
2 : 1 max.
Output Load V.S.W.R.
-120 dBc/Hz max. @ 100 Hz-130 dBc/Hz max. @ 1 kHz
IM-T8103 Rev.01
10 MHz (sine-wave)-5 to +5 dBm @ Input port
@ Pout = +34.5 dBm
[Input Power][Frequency]
Requirement for External
7.1. Electrical Specifications
NJT8103 series Instruction Manual Page 21
<N-type Model><F-type Model>
2.
1 mm p-p (3 axis, 5 to 50 Hz)
EMC (2014/30/EU)RoHS (2011/65/EU)Safety: EN60950-1
15,000 feet (4,572 m)
without Interface Connector
No. Item Specifications16. DC Power Requirement
F-type female connector, 75 ohms
[Voltage Range] +24 VDC (+12 to +30 VDC)
N-type female connector, 50 ohms
No.
@ Pout = +34.5 dBm2 W max. @ 10 MHz ref. off (Mute on)
Output Interface3.
1.
Waveguide, WR75 (with Groove)
7.2. Mechanical and Environmental Specification:
18 W typ. @ No IF signal21 W typ., 25 W max.
Dimension & Housing
(L)
17. Mute Shut off the HPA in case of L.O.unlocked
[Power Consumption]
IF / Ref. / DC Power:Input InterfaceItem Specifications
[Operating]
800 g [1.8 lbs]
7. Humidity
Weight5. Cooling Convection Cooling
(H)4.
85 mm [3.35"]56 mm [2.20"]
[Storage]
(W)
6. Temperature Range (ambient)
-40 to +75 °C-40 to +60 ºC
IM-T8103 Rev.01
135.4 mm [5.33"]
13. Comply with RoHS (Restricting the use of Hazardous Substances)directives
12. Regulatory Compliance EU Directive (CE Marking)IP67 (IEC 60529)11. Dustproof / Waterproof
0 to 100 %
10. Shock 30 G [294.2 m/s2] (3 axis)
9. Vibration 5 G [49.03 m/s2] (3 axis, 50 Hz to 2 kHz)
8. Altitude