INSTALLATION, OPERATING AND SERVICE MANUAL ONE TM …lancasterwatergroup.com/wp-content/uploads/Product... · 2018. 1. 30. · CT-4.5DRAIN 4.5” Bottom Drain Plumbing For Commercial

Congratulations on purchasing your new Lancaster Water Filter. This unit is designed to give you many years of trouble free service. For servicing and future inspection purposes, please file this booklet with your important documents. In the event that you need assistance for servicing your water filter, please first contact the professional contractor who installed the system.

ONE TM CARTRIDGE TANK FILTRATION SYSTEM

INSTALLATION, OPERATING AND SERVICE MANUAL

7-CTFS-125

CT-1005

CT-2010

CT-5020

CT-2050-SWMB

CT-5020-SWMB

CT-03-CB

CT-20-CB

CT-03-CB AMINE

7-CTFS-2

CT-P1A

CT-P05

CT-P20

CT-D05

CT-D20

Natural Blue Almond

Grey Black

Available in 5 standard colors.Custom colors available upon request.

CARTRIDGE TANK®FILTRATION SYSTEM

Say goodbye to small and inefficient housings. Get rid of expensive stainless steel housings. The ENPRESS Cartridge Tank® is a direct replacement for small and inefficient 2 ½” or 4 ½” housings, or expensive Stainless Steel cartridge housings, and offers extended service and life, and a more cost-effective and efficient filtration solution.

Utilizing ENPRESS’ patented industry exclusive liner design and no tools necessary snap-ring design; Full radial seal top and bottom caps make replacement simple. Cartridge Tank® makes it easy to access and remove the internal filtration solution.

Lightweight and cost effective with multiple configuration options, from high flow commercial/industrial applications to stand-alone residential Point-of-Entry (POE) installations for city and well water applications, this is the filtration solution of the future…100% non-metallic! The Cartridge Tank® is a high performance, NSF 42 listed device and has been tested to 100 psi operating pressure with 4:1 Burst Safety Factor.

Features100% non-metallic!

Patented no-tools necessary snap-ring design

Multiple filtration solutions

Full 1 ¼” and 2” plumbing connection options

Large capacity filter configurations

BenefitsLightweight and cost effective housing with high chemical compatibility.

Simple and easy change-out of cartridges. No Tools, Means NO TOOLS!

Match the filtration solution with flow rate requirements

Extended service life, contaminant removal, and dirt holding capacity

Low pressure drop = high flow

ApplicationsIdeal for Residential, Food Service, Rental Fleets, Commercial and Industrial Applications

Make-up Water, RO Pre-filtration, Cooling Towers, Chill Water Loops, Metal Finishing

Process Water (turbidity, particulate, colloidal suspensions)

Reduction of unwanted bad taste and odor from potable drinking water

City water applications where water softeners are a hard sell…as a replacement option of pitcher, faucet, bottled water and/or refrigerator filters

Reduction in frequency of replacing common 2 ½” or 4 ½” housings…Bigger is Better

Other water-based fluid solutions

OR GR BLYE WH RE PU

5

Provisions should be made to install three bypass valves around the EF-835-2 cartridge filter tank. Because of the pipe size, this will need to be created on the job site. Any piping materials may be used; however, be sure to observe local plumbing codes. These bypass valves should allow for water to be turned off to the filter tank for future cartridge replacement, and allow for system bypassing should other service be required.

BYPASS INSTALLATION FOR EF-835-2:

NOTE: Drain should be considered in plumbing of system as per diagram. Opening drain valve will allow for flushing of cartridge. Closing inlet and outlet valve and opening drain will relieve pressure on filter tank for cartridge replacement.

The cartridge filter is shipped separately from the cartridge tank assembly and must be installed prior to use.

Placement of the Cartridge Tank Filtration System is dependant on the application. Locate the system close to a drain. A bottom drain can be installed in the plumbing system to allow rinsing of the cartridge. Some water may spill when replacing the cartridge. Precautions should be taken to prevent any damages due to water while replacing or rinsing the cartridge. FOLLOW ALL LOCAL PLUMBING CODES. Shut off valves should be installed for ease in servicing the system.

Typical installation show with bypass

Optional

Installation & Cartridge Replacement Instructions

1. Turn off water supply to system by shutting off inlet and outlet valves.2. Properly depressurize system by pushing red depressurization button on top cap of system. Keep

button pushed until all air or water pressure is completely released. (See PICTURE 1)3. Push top cap down equally with both hands to unseat retaining ring. Remove ring from groove

by carefully grasping handles and pulling inward then upward. Ring will slide completely out of groove. (See PICTURE 2 & 3)

4. Remove top cap of system by lifting up on top handles. (See PICTURE 4)5. For Cartridge Replacement: Remove replacement cartridge carefully from bag. Retain bag for

disposal of used cartridge. Remove used cartridge from system by grasping handle and pulling upward while holding the tank down. Place in bag and dispose of in accordance with local, state and federal laws and regulations. If necessary, open drain and flush system further with a bucket of water to remove final sediment and particles. Once flushed, close drain line.

For New Installation: Remove plastic covering surrounding filter cartridge and discard. Lubricate O-rings on cartridge to ensure proper sealing. Do not use pipe dope, Vaseline, oils or other unacceptable lubricants on O-rings. Food grade silicone lubricant is recommended. Insert cartridge into bottom center of tank, assuring proper seal and alignment by pushing down gently until fully seated.

6. Attach product description tag to retaining ring handle for future reference.7. Replace top cap of tank using top handles.8. Push top cap down to make room for placement of retaining ring in ring groove.9. Insert retaining ring into ring groove, starting at the end opposite of the handle. Using only hands,

gently push retaining ring into groove until entire ring is in place and both ends meet in groove section.

10. Slowly turn water supply on to system by first opening inlet valve and pressing red depressurization valve to completely vent tank of trapping air. When water leaks out of depressurization valve, stop pushing and open outlet valve.

11. Check system for leaks and ensure system integrity.

PIC

TUR

E 2

PIC

TUR

E 1

PIC

TUR

E 3

PIC

TUR

E 4

Replacement Parts7-CTFS-125 Residetial

IMAGE NAME PART NO. DESCRIPTION QTY.1 CT-RETAININGRING Snap Ring With I. D. Tag Connection For Top And Bottom. 22 CT-1/4NPTLID Top Cap With Pressure Release Valve & Removal Handles 13 R-ORING LID O-ring Replacement For All Lids/Caps 2

(Not pictured) FG840CARTRIDGE TANK 8” x 40” Vessel Shell With Base 14 CT-2.5LID 2.5” Threaded Bottom Residential Cap, Threaded Connection. 1

6CT-2.5DRAIN 2.5” Bottom Drain Plumbing For Residential Filters. 1

CT-2.5ADAPTER Adapter Tee For 2.5” Opening 1CARTRIDGES (CHOOSE 1)

OrangeCT-1005 30 GPM, 10 PRE/5 INNER, Dual Gradient Double Pleated 1CT-2010 30 GPM, 20 PRE/10 INNER, Dual Gradient Double Pleated 1CT-5020 30 GPM, 50 PRE/20 INNER, Dual Gradient Double Pleated 1

YellowCT-2050-SWMB 30 GPM, 20 PRE/5 CORE, Dual Gradient Polypropylene String/Melt Blown Polypropylene Core 1

CT-5020 SWMB 30 GPM, 50 PRE/20 CORE, Dual Gradient Polypropylene String/Melt Blown Polypropylene Core 1

BlueCT-03-CB 30 GPM, 3 Micron, Carbon Block 1CT-20-CB 30 GPM, 20 Micron, Carbon Block 1

CT-03-CB AMINE 30 GPM, 3 Micron, Carbon Block-Chloramines 17-CTFS-2 Commercial

IMAGE NAME PART NO. DESCRIPTION QTY.1 CT-RETAININGRING Snap Ring With I. D. Tag Connection For Top And Bottom. 22 CT-1/4NPTLID Top Cap With Pressure Release Valve & Removal Handles 13 R-ORING LID O-ring Replacement For All Lids/Caps 2

(Not pictured) FG840CARTRIDGE TANK 8” x 40” Vessel Shell With Base 15 CT-4.5LID 4.5” Threaded Bottom Commercial Cap Threaded Connection. 1

7CT-4.5DRAIN 4.5” Bottom Drain Plumbing For Commercial Filters. 1

CT-4.5ADAPTER Filter Tee For Commercial Filter 1CARTRIDGES (CHOOSE 1)

RedCT-P1A 50 GPM, 1 Absolute Micron 1CT-P05 100 GPM, 5 Micron, Pleated Polypropylene 1CT-P20 150 GPM, 20 Micron, Pleated Polypropylene 1

PurpleCT-D05 100 GPM, 5 Micron, Melt Blown Polypropylene Depth 1CT-D20 150 GPM, 20 Micron, Melt Blown Polypropylene Depth 1

TANK RISER

Recommended:

Drain installed on inlet side of system, for removal of contaminants in sediment applications.

Drain installed on outlet side of system, for flushing of new cartridges that have dust (i.e. Blue Series)

Top Cap option with pressure release Valve &

Removal Handles

Snap Ring with I.D. Tag connection.

LIFT TOP CAPPRESS THE RED PRESSURE RELIEF VALVE & PULL SNAP-RING

COLOR-CODED CARTRIDGE FILTRATION SERIES

ENPRESS, LLC. | 34495 Melinz Parkway, Eastlake, OH 44095 | Phone 866.859.9274 | Fax 440.510.0202 | [email protected]

© ENPRESS LLC 2013 ELLC #002 - 03/2013

This pressure vessel is tested and certified by NSF International against NSF/ANSI Standard 61 for materials and structural integrity requirements

COMPONENT

For more information, visit enpress.com

or oneFiltration.com

ONE® is an ENPRESS Filtration Technology

Technical Schematics

Easy Replacements - No Tools Means No Tools

Available Optionsand Configurations

OR GR BLYE WH RE PU

Item #: CT‐1/4NPTLID

Item #: CT‐RETAININGRING

Item #: CT‐2.5LID

Item #: CT‐2.5DRAINCT‐2.5ADAPTER

Item #: CT‐4.5LID

2.5” Threaded top/bottom

Res./LC Cap threaded

connection.

2.5” Bottom Drain Plumbing

for Res./LC Filters.


Commercial Cap threaded

connection.


for Commercial Filters.


TANK RISER

Recommended:




Removal Handles





© ENPRESS LLC 2013 ELLC #002 - 03/2013


COMPONENT







OR GR BLYE WH RE PU



Item #: CT‐2.5LID


Item #: CT‐4.5LID



connection.





connection.




TANK RISER

Recommended:




Removal Handles





© ENPRESS LLC 2013 ELLC #002 - 03/2013


COMPONENT







OR GR BLYE WH RE PU



Item #: CT‐2.5LID


Item #: CT‐4.5LID



connection.





connection.




TANK RISER

Recommended:




Removal Handles





© ENPRESS LLC 2013 ELLC #002 - 03/2013


COMPONENT







OR GR BLYE WH RE PU



Item #: CT‐2.5LID


Item #: CT‐4.5LID



connection.





connection.




TANK RISER

Recommended:




Removal Handles





© ENPRESS LLC 2013 ELLC #002 - 03/2013


COMPONENT







OR GR BLYE WH RE PU



Item #: CT‐2.5LID


Item #: CT‐4.5LID



connection.





connection.




TANK RISER

Recommended:




Removal Handles





© ENPRESS LLC 2013 ELLC #002 - 03/2013


COMPONENT







OR GR BLYE WH RE PU



Item #: CT‐2.5LID


Item #: CT‐4.5LID



connection.





connection.




Image 1 Image 2 Image 3 Image 4 Image 5 Image 6 Image 7

Orange Yellow Blue Red Purple

A DIVISION OF C-B TOOL CO.1340 MANHEIM PIKE ● LANCASTER PA 17601-3196 ● TEL:717-397-3521 ● FAX: 717-392-0266

www.lancasterwatertreatment.com ● E-mail: [email protected]/13

Documents

INSTALLATION, OPERATING AND SERVICE MANUAL ONE TM …lancasterwatergroup.com/wp-content/uploads/Product... · 2018. 1. 30. · CT-4.5DRAIN 4.5” Bottom Drain Plumbing For Commercial