Upload
dinhthuan
View
221
Download
3
Embed Size (px)
Citation preview
Publications No.
Issue DateINSTALLATIONINSTRUCTIONS
Accessory Application
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42425 (0908) 1 of 1508B15-SNC-1B02-91
AII 42425XM RADIO SYSTEM
2010 CIVICHYBRID
AUG 2009
PARTS LISTXM Radio Attachment (sold separately):P/N 08B15-SNA-100BBus cable
Front bracket
Rear bracket
Clip
4 Pan screws
4 Washers
3 Flange bolts
Cover seal
20 Wire ties (1 Not used)
7 Wire ties with clip (2 Not used)
12 Cushion tapes (4 Not used)
8 EPT sealers (Some may not be used.)
XM Antenna (sold separately):P/N 08A15-0J1-100Antenna assembly
2 of 15 AII 42425 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
XM Radio Unit (sold separately):P/N 08A15-3J1-000XM radio unit
2-Port Bus Cable (sold separately):P/N 08A31-0F1-0002-Port bus cable
TOOLS AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriverRulerShop towelScissorsRatchet10 mm Socket10 mm Combination wrenchIsopropyl alcohol(Isopropyl alcohol, in a 60/40 solution with water)Rubber malletTORX bitDiagonal cuttersMasking tapePlastic Trim Tool (T/N SILTRIMTL10)
Illustration of the XM Radio System Installed on the Vehicle
6623010H
ANTENNA
XM RADIO UNIT
BUS CABLE
6621020H
XM RADIO UNIT
AUDIO UNIT
ANTENNA
BUS CABLE
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42425 (0908) 3 of 15
INSTALLATION
1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the audio presets.
2. Disconnect the negative cable from the battery.3. Remove the passenger’s dashboard lower cover
(four clips and two pins).
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
5306360T
PASSENGER’SDASHBOARD LOWER COVER
4 CLIPS
2 PINS
4. Remove the two bolts under the glove box.
5. Open and remove the glove box (two stops).6. Remove the driver’s dashboard lower cover (eight
clips).
5202260T
2 BOLTS
GLOVE BOX2 STOPS
5202121T
8 CLIPS
DRIVER’SDASHBOARDLOWER COVER
4 of 15 AII 42425 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
7. Remove the inside cover from the front console pocket (two tabs).
8. Lower the tilt lever, then pull the steering wheel toward you.
9. To protect the dashboard area, put shop towels over the steering wheel and shift lever.
5202130T
SHIFT LEVER(S or 2POSITION)
FRONT CONSOLE POCKET
INSIDECOVER
2 TABS
5629030H
SHOP TOWEL
STEERINGWHEEL
SHOP TOWEL
COMBINATIONSWITCH
SHIFT LEVER
TILT LEVER
10. Apply masking tape to the instrument panel as shown, and remove the meter panel (one self-tapping screw and 11 clips, and unplug the vehicle connectors).
11. Pull the aspirator hose off the air conditioner sensor.
6719010H
SELF-TAPPING SCREW
11 CLIPS
METER PANEL MASKING TAPE
VEHICLE CONNECTOR
VEHICLE CONNECTOR(If equipped.)
5805020H
AIR CONDITIONERSENSOR
ASPIRATORHOSE
METER PANELOPENING
CENTER PANEL
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42425 (0908) 5 of 15
12. Apply masking tape to the instrument panel as shown. Remove the center panel (two bolts and 11 clips, and unplug the vehicle connectors).
5202563T
5 CLIPS
2 BOLTS
VEHICLECONNECTORS
MASKING TAPE
CENTER PANEL
6 CLIPS
13. Pull back the weatherstrip in the area shown.
14. Push the clip into the vehicle side by striking the top of the passenger’s A-pillar trim in the part marked as “SIDE CURTAIN AIRBAG” with a rubber mallet perpendicularly to the vehicle.
15. Pull the weatherstrip off in the area shown. Then remove the A-pillar trim (two clips).
5718021H
A-PILLAR
PINCLIP
RUBBER MALLET(Strike perpendicularly.)
WEATHERSTRIPPASSENGER’SA-PILLAR TRIM
CLIP
A-PILLAR TRIM
5202250T
PASSENGER’SA-PILLAR TRIM2 CLIPS
WEATHERSTRIP
6 of 15 AII 42425 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
16. Remove the cap from the right sunvisor (four retaining tabs).
17. Remove the right sunvisor (two T25 TORX screws, and unplug the vehicle connector, if equipped).
18. Remove the sunvisor holder. Turn the holder 90°, then pull it out.
19. Remove the center console cover (five clips).
5321090H
VEHICLE CONNECTOR(If equipped.)
4 RETAININGTABS
CAP
2 TORX SCREWS
SUNVISORHOLDER
RIGHT SUNVISOR
5202173T
3 CLIPS CENTER CONSOLECOVER
PARKING BRAKE LEVER(Pull up completely.)
SHIFT LEVER(D POSITION)
2 CLIPS
20. Open the center console lid, and remove the mat.
21. Remove the center console (four bolts and two clips, and unplug the vehicle connector).
22. Remove the rear seat cushion (one bolt and release the two hooks).
5202184T
4 BOLTS
MAT
2 CLIPS
CENTER CONSOLELID
VEHICLECONNECTOR
CENTER CONSOLE
5202363T
BOLT
REAR SEAT CUSHION
2 HOOKS
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42425 (0908) 7 of 15
23. Remove the three bolts fastening the rear seat-back and pull the rear seat-back up to release the three hooks. Remove the rear seat-back.
24. Remove the right rear side step trim (four clips and three retaining tabs).
5414031H
3 BOLTS
REAR SEAT-BACK
3 HOOKS
5202580T
4 CLIPS 3 RETAININGTABS
FRONT
RIGHT REAR SIDE STEP TRIM
25. Open the trunk lid, and remove the trunk floor mat.
26. Pull bakc the trunk weatherstrip in the area shown. Remove the rear trim panel (four clips and three hooks).
5425021H
TRUNK FLOOR MAT
5202451T
TRUNKWEATHERSTRIP
4 CLIPS
REAR TRIM PANEL3 HOOKS
8 of 15 AII 42425 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
27. Inside the trunk, remove the front trunk lining (six clips).
28. Pull back the weatherstrip. Remove the four clips, then pull out the right trunk side trim panel.
5418071H
5 CLIPS
FRONT TRUNK LINING
LARGE CLIP
5414042H
RIGHT TRUNK SIDE TRIM PANEL
CLIP
3 CLIPS(Turn the center pin counterclockwise to remove.)
WEATHERSTRIP
Routing the Bus Cable29. Route the bus cable from the trunk along the vehicle
harness.
30. Remove the clip that secures the floor carpet. Pull back the floor carpet.
31. Route the bus cable forward under the floor carpet.
5714130H
BUSCABLE
VEHICLE HARNESS
5218092H
BUS CABLE(Route under the floor carpet.)
FLOOR CARPET
CLIP
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42425 (0908) 9 of 15
32. Route the bus cable forward along the vehicle harness to the right front of the console frame .
33. Route the bus cable connector to the dashboard and out through the dash opening.
5221022H
BUS CABLE
DASH OPENING
DASH OPENING
VEHICLE HARNESS
Routing the Antenna Cable34. Using isopropyl alcohol on a shop towel, clean the
area shown on the inside of the windshield.
35. Remove the adhesive backings from the antenna, and attach the antenna to the location shown. Apply sufficient pressure so that the antenna adheres completely to the windshield.
871520AR
10 mm (0.4 in.)
3 mm (0.1 in.)
ANTENNA
<INSIDE>
ANTENNA
FRONT WINDOW
4 ADHESIVE BACKINGS
10 of 15 AII 42425 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
36. Attach masking tape to the location shown.
37. With isopropyl alcohol on a shop towel, clean the area shown on the outside of the windshield.
38. Remove the adhesive backing from the cover seal, then attach to the location shown. Remove the masking tape.
39. With scissors, cut three EPT sealers in half.
871521AR
Align with end of the masking tape.
5 mm (0.2 in.)
ADHESIVE BACKING
COVER SEAL
<OUTSIDE>
6 mm (0.24 in.)
MASKING TAPE
871604AR
ANTENNA
ANTENNA CABLE
6 HALF EPT SEALERS
EPT SEALER(Cut in half.)
PASSENGER’S A-PILLAR
VEHICLE HOLES(Do not attach the half EPT sealers.)
40. Route the antenna cable down along the passenger’s A-pillar. Using the six pieces of EPT sealer, secure the antenna cable to the A-pillar panel in the areas shown after cleaning with isopropyl alcohol on a shop towel.
NOTE: Do not attach the half EPT sealers to the vehicle holes, pay attention to the orientation of the half EPT sealers.
41. Clean the vehicle bracket shown with isopropyl alcohol on a shop towel, then attach one EPT sealer to the bracket.
42. Route the antenna cable down behind the dashboard stay and toward the glove box. Using three wire ties, secure the antenna cable to the vehicle harness.
5322011H
3 WIRE TIES
ANTENNA CABLE VEHICLE HARNESS
EPT SEALER
VEHICLE BRACKET
DASHBOARD STAY
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42425 (0908) 11 of 15
43. In the glove box opening, route the antenna cable along the vehicle harness and toward the audio unit opening. Secure the antenna cable to the vehicle harness with one wire tie in the area shown.
44. Route the antenna cable down along the bus cable as shown.
45. Measure 300 mm (11.8 in.) from the end of the bus cable connector, then secure the bus cable and antenna cable to the vehicle harness with six wire ties.
5322020H
VEHICLE HARNESS
WIRE TIE
ANTENNA CABLE
5322043H
2 WIRE TIES
BUS CABLECONNECTOR
ANTENNA CABLE
300 mm (11.8 in.)
2 WIRE TIES
2 WIRE TIES
46. Route the antenna cable along the bus cable, secure the bus cable and antenna cable to the vehicle harness with four wire ties.
47. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Attach the bus cable and antenna cable to the floor panel with the two cushion tapes in the area shown.
5322051H
VEHICLE HARNESS
BUS CABLE
2 CUSHION TAPES
ANTENNACABLE
2 WIRE TIES
2 WIRE TIES
12 of 15 AII 42425 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
48. Route the antenna cable along the bus cable, turn over the floor carpet, then attach the bus cable and antenna cable to the floor panel with the two cushion tapes in the areas shown after cleaning with isopropyl alcohol on a shop towel.
49. Secure the bus cable and antenna cable to the vehicle harness with the three wire ties in the areas shown.
5322061H
2 CUSHION TAPES
VEHICLE HARNESS
BUS CABLE
Turn over.
ANTENNA CABLE
BUS CABLE
<SIDE VIEW>
CUSHION TAPE
ANTENNA CABLE
3 WIRE TIES
50. Route the antenna cable along the bus cable, secure the bus cable and antenna cable to the vehicle harness with the two wire ties in the areas shown.
51. Attach the bus cable and antenna cable to the floor panel with the three cushion tapes in the areas shown after cleaning with isopropyl alcohol on a shop towel.
5715040H
VEHICLE HARNESS 3 CUSHION
TAPES
ANTENNACABLE
BUS CABLE
2 WIRE TIES
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42425 (0908) 13 of 15
Installing the XM Radio Unit52. Using four pan screws and four washers, install the
front and rear brackets to the XM radio unit.
53. With isopropyl alcohol on a shop towel, clean the trunk right inner panel in the area shown.
54. Attach one EPT sealer to the trunk right inner panel as shown.
6622080H
FRONTBRACKET
REARBRACKET
2 PAN SCREWS
XM RADIO UNIT
2 PAN SCREWS
4 WASHERS
6724020H
EPT SEALER
TRUNK RIGHTINNER PANEL
Clean.
55. Plug the bus cable connector and the antenna cable connector in the XM radio unit.
56. Using one cushion tape, secure the antenna cable to the XM radio unit in the area shown after cleaning with isopropyl alcohol.
57. Loosely tighten three flange bolts to the front and rear brackets. On the front bracket, use the “A”-marked holes.
58. Place the XM radio assembly to the back of the trunk right inner panel. Set three flange bolts into the elongated holes in the body panel.
59. Tighten the three flange bolts.
CUSHION TAPE
TRUNK RIGHTINNER PANEL
XM RADIO UNIT
BUS CABLE
ANTENNA CABLE1-PIN CONNECTOR
BUS CABLE14-PIN CONNECTOR
ANTENNA CABLE
6623041H
XM RADIO UNIT
3 ELONGATEDHOLES
RIGHT TRUNKINNER PANEL
FLANGE BOLT
FLANGE BOLT
FRONT BRACKET
REAR BRACKET
“A”-MARKEDHOLE
14 of 15 AII 42425 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
60. Using three wire ties with clips, secure the bus and antenna cables in the areas shown.
61. Using two wire ties with clips, bundle the excess of the bus and antenna cables to the holes on the right trunk inner panel.
6724030H
2 WIRE TIES WITH CLIP in step 61
Bundle the excesscables.
3 WIRE TIESWITH CLIPSin step 60
XM RADIO UNIT
RIGHT TRUNKINNER PANEL
If the vehicle you’re working on is equipped with a CD Changer, go on to step 62; otherwise, go to step 64.62. Plug the 2-port bus cable connectors into the two
bus cables.
63. Wrap the two plugged connectors using two EPT sealers.
64. Plug the bus cable connector into the audio unit.
6622050H
2-PORTBUS CABLE
2 BUS CABLES
2 EPT SEALERS
6724040H
BUS CABLE or 2-PORT BUS CABLE
AUDIO UNIT
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42425 (0908) 15 of 15
65. Plug the vehicle connectors to the center panel, and reinstall the center panel.
66. Replace the old clip on the right front pillar trim with a new one.
5420071H
CENTER PANEL
VEHICLE CONNECTORS
2 BOLTS(Reuse.)
5323070H
NEW CLIP
OLD CLIP(Discard.)
RIGHT FRONTPILLAR TRIM
67. Check that all wire harnesses are routed properly and all connectors are plugged in.
68. Reinstall all removed parts.69. Connect the negative cable to the battery and check
operation of all lights and other electrical accessories.
70. Enter the anti-theft codes for the audio system and the navigation system (if equipped), and reset the radio station presets.
71. Reset the clock on vehicles without navigation.72. Check the operation of the XM radio system.73. If the IMA battery level gauge (BAT) displays zero
segments, start the engine, and hold it between 3,500 and 4,000 rpm (in Park or Neutral) until the gauge displays at least three segments.
74. Initialize the auto up/down feature for the front windows.