Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
Install Guide for MOD2, NA Petroleum Canopy Power Supply Kit
PN: 601074 (75 W), 601075-088 (88 W), 601075-105 (105 W), 601075 (150 W), with MODUS fixture. 601076 (200 W) with MODUS HO (High Output) fixture.
PAGE 1 OF 3
IMPORTANT: PDL3 MODUS must only be used with 601074 (75 W) or 601075 (150 W) power supplies. PDL3 MODUS HO (High Output) must only be used with 601076 (200 W) power supply. PDL3 MODUS CANNOT be used with 601076 (200 W) power supply.
NOTE: A LICENSED ELECTRICIAN SHALL MAKE ALL PRIMARY AND SECONDARY CONNECTIONS.
Tools and supplies required: Cordless drill, adjustable end wrench (1.25 in/32 mm minimum opening), putty knife, tape measure, Phillips-head screwdriver, and twist-on or push-in UL Listed wire connectors for 14/18 AWG.
2. Install PDL3 MODUS: See PDL3 MODUS installation instructions.
1. Turn off power.
3. Remove any loose debris from around hole on top of canopy. Remove as much roof tar as possible in a 7" diameter circle around canopy hole, if present
5. Loosen gland fitting on power supply side of power module tube.
Power module tube
Power supply
Gland fitting
Enclosure lid
PDL3 MODUS
side
4. Assemble enclosure over top of installed fixture, making sure to tighten hex nut enough to compress gasket slightly.
Wire from PDL3
MODUS
Hub
Lid
Hex nut
GasketInstalled PDL3 MODUS fixtureTop of canopy
Enclosure
Enclosure
QUICK REFERENCE PARTS GUIDE
Enclosure cover
Large hex nut
Orange foam
gasket
Power Module
tube
Enclosure cover
Ground wire
Power supply
Power Module tube
Gland fittingsPower Module
Gland nut
Gland nut
ConnectorCable gland
Cable toPDL3
MODUS Cable topower supply
O-ringGray
seal ring
Attach power supply to enclosure cover with two self drilling sheet metal screws and speed nuts provided.
Install Guide for MOD2, NA Petroleum Canopy Power Supply Kit
PN: 601074 (75 W), 601075-088 (88 W), 601075-105 (105 W), 601075 (150 W), with MODUS fixture. 601076 (200 W) with MODUS HO (High Output) fixture.
PAGE 3 OF 3
Customer service and technical support888.747.4LED (888.747.4533)SloanLED.com • [email protected]
Europe: Customer service and technical support+31 88 12 44 900 SloanLED.com • [email protected]
P/N 402067 Rev E 2019-06-28
US patents and foreign patents pending
Luminaire does not light after complete installation. Check connection from power supply lead to luminaire. Verify all pins in connectors are properly seated. Still does not light. Disconnect luminaire from power supply. Check output voltage of power supply using a voltmeter. The output voltage should be within ± 3 V of the voltage
shown in the table above. If there is no output voltage, have a licensed electrician check input voltage. Make sure power supply is connected correctly and getting primary power. If power supply is connected properly and getting primary power and there is still no output voltage, replace power supply.
Still does not light. If power supply is getting primary power, has the correct output, and luminaire does not light, there may be a short in the secondary wiring. Check all connections and the condition of the wires. Measure luminaire input resistance across the red and black leads. This should be an open circuit on typical handheld multimeters.
Troubleshooting
*When using 410180 power supply, use of Jumper Select Control Module P/N 601063-200 or 410168 is required to maintain warranty consideration. When using 410168, customer must provide waterproof junction box. Consult factory for control voltage settings. Failure to obtain control voltage settings from factory voids warranty.
601075 Input Output
Power Module Setting Nominal input voltage Input currentPower output
limitOutput current
limitLuminaire per power supply
No Jumper = High power 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 125 W 2.3 A 1
#1 Jumper = Mid power** 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 105 W 2.0 A 1
#2 Jumper = Low power** 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 88 W 1.6 A 1
701932 and 410168* 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC User setting 125 W max User setting 2.3 A max 1
150 Watt power supply capacity chart for PDL3 MODUS (White connectors on power supply)
601074 Input Output
Power Module Setting Nominal input voltage Input currentPower output
limitOutput current
limitLuminaire per power supply
No Jumper = High power 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 66 W 1.3 A 1
#1 Jumper = Mid power 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 51 W 1.1 A 1
#2 Jumper = Low power 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 36 W 0.9 A 1
410181 and 410168* 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC User setting 65 W max User setting 1.3 A max 1
75 Watt power supply capacity chart for PDL3 MODUS (White connectors on power supply)PDL3 MODUS
**For 601075-088 and 601075-105, power output is fixed at 88 W and 105 W respectively, and is not jumper selectable.
601076 Input Output
Power Module Setting Nominal input voltage Input current Power output limit Output current limitLuminaire per power supply
No Jumper = High power 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 157 W 0.75 A 1
#1 Jumper = Mid power 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 133 W 0.65 A 1
#2 Jumper = Low power 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC 116 W 0.57 A 1
410180 and 410168* 90-307 VAC, 47-63 Hz 2.0 A at 110/220 VAC User setting 165 W max Consult factory 1
200 Watt power supply capacity chart for PDL3 MODUS High Output (Black connectors on power supplies)PDL3 MODUS HO (High Output)