Initialization file LTire.ini / LTireW.iniThe following setups
are possible in the configuration file LTire.ini (LTire 5 and 6) /
LTireW.ini (LTire 7):[ProgramPar]ZeitAnzeige=OnSwitches the time
display in output dialog on/off.SaveBackground=OnSwitches the
storing of backgrounds of dialogs on/off. If very small main memory
is available, this option should be switched off, because this
function operates memory intensively.
Function method:
SaveBackground=On: After leaving a dialog the previously stored
graphics of a dialog is drawn again. Advantage: Considerably faster
screen-up time, especially when handling large quantities of
data.Disadvantage: Greater memory requirement
SaveBackground=Off: After leaving a dialog the graphics are
constructed anew. OffsetDialog=OnSafety function.Switches the
button for calling up the offset-dialog in the machine parameter-
dialog on or off. If the button is switched off, an accidential
changing of the offset values by the user is almost impossible.
Wrong offset values are difficult to recognize at first sight, but
they usually lead to completely wrong engraving
results.SPSServiceDialog=OffOnly LANG service technical engineers
use this function !Undo=2Determines the number of Undo steps. Here
it is to note, that a large amount of Undo steps requirers a large
amount of physical main memory. Undo-functionMarkLine=1Indicates
the line thickness of the marked data in pixels. A line thickness
of 2-3 pixel is suitable for representing marked data. For the edit
functions, a line thickness of 1 pixel is suitable, because it is
easier to recognize a contour with very thin lines. The following
attitudes proved
effective:machine-pc:MarkLine=3construction-pc:MarkLine=1Edit=OnIt
indicates whether the complete edit menu is active or inactive. The
edit menu on the machine-pc should be inactivated, so that an
unintentional changing of the data is
prevented.machine-pc:Edit=Offconstruction-pc:Edit=On[Werkzeugwechsler]Note:
Only one of the following three options may be selected.WW=24-fach
Trommelif 24 station drum changer and measuring system are
installed.WW=Messpunkt if no tool changer, but measuring system is
available.WW=Handif neither tool changer nor measuring point is
available.SPS=OnEnables the communication with the SPS controller
if it is available. This is essential for the 24 station drum
changer.StreckeY=50Gives the distance of the Y-axis in [mm], which
should be covered, when it is driven from the tool change position
to the measuring point. If very long tools are used, 50[mm] can be
too less. In this case collision could occur.[MaschPar]The
following adjustments in the part [MaschPar] configures the
machine. Except for the adjustment the values should not be changed
by the user or machine operator.1=Schr/Umdr Tisch :6400Gives the
step resolution of the round table. This value should never be
changed by the user or machine operator.2=Gdr/Umdr Tisch :1.0Gives
the step resolution of the round table. This value should never be
changed by the user or machine operator.3=GSW Motorfahren :127Gives
the max. speed of the axis when operated manually. This value
should only be changed, if offset problems occur in the machine
setup menu while moving the axis manually.Res=1.0Gives the max
length of a vector section in [mm], which are generated while
projecting/roll on surface the data onto the tire side-wall
mold.
Basic rules:The smaller the radius of the tire mold the smaller
should be the vector section, i.e. the resolution has to be
increased for narrow curves.
Value range:For a normal tire molds the value 1.0 turned itself
out as optimal. The value can be reduced to 0.5 up to 0.25 for
narrow molds, but it should never be below 0.2. A bigger value is
only useful for flat molds.
Consider:A smaller value than 1.0 is only practical, if the
distance of the scannning steps are decreased, i.e. a vector
section of 0.5 [mm] should also be scanned with scanning steps of
0.5 [mm].Spindel=SPS,MCGThis value configures the switch-on of the
spindle. This value should / never be changed by the user or
machine operator. Spruehen=SPS,MCGThis value configures the
switch-on of the lubrication unit. This value should / never be
changed by the user or machine operator. [CalibPar]The following
setups in the section [CalibPar] are adjusted by LANG to the
corresponding machine. These settings should not be changed by the
user / machine operator.Gsw-T=10Drive speed of the turntable during
calibration process.Gsw=40Drive speed of the Y-axis during
calibration process.Gsw=40Drive speed of the Z-axis during
calibration process.Gsw=10Drive speed of the W-axis during
calibration process.Rampe-T=4Ramp of the turntable during
calibration process.Rampe-Y=4Ramp of the Y-axis during the
calibration process.Rampe-Z=4Ramp of the Z-axis during the
calibration process.Rampe-W=4Ramp of the W-axis during the
calibration process.[SpindlePar]Max=7000Max. achievable spindle
current. Serves for display of the spindle current in the
engraving-dialog.Kritisch=5000Critical zone of spindle current
(overload). Serves for display of the spindle current in the
engraving-dialog.
Comparison list LCADR -> LTIREWhere to find which function
?LCADRLTIRE
[INFO] / [LANG GMBH][?] / [Program information]
[INFO] / [GRAPHIC FORM]Button in vertical toolbar
[INFO] / [RASTER]see: LANG-Windows-Program LCAD
[INFO] / [MOUSE] / [RESOLUTION]Windows Control Panel or a
special mouse driver
[INFO] / [MOUSE] / [Circle around mouse pointer]Button in
vertical toolbar (Measuring)
[FILE] / [INIT][File] / [New] or Button in horizontal toolbar or
Strg+N
[FILE] / [DIR]Windows File Manager
[FILE] / [LOAD FILE][File] / [Load] orButton in horizontal
toolbar or Strg+O
[FILE] / [RELOAD FILE][File] / [Add]
[FILE] / [STORE LAYER]
[FILE] / [LCADM-DATA][Construction] / [Object from library] /
[Create LG1-file]
[FILE] / [END][File] / [Quit] orAlt+F4 in main window
[SYSTEM] / [TOOLS][Setup machine] / [Tools] orButton in the
horizontal toolbar or Strg+W
[SYSTEM] / [DISPL. TOOLS][Setup machine] / [Tools] orButton in
horizontal toolbar
[SYSTEM] / [COLOR SELECT][Setup machine] / [Tools] /
[Colour]
[SYSTEM] / [DISPL. LAYER][Work on] / [Object Info] or[Work on] /
[Used tools]
[SYSTEM] / [PLOT][File] / [Printer configuration] and [File] /
[Draw => Printer/Plotter] or Strg+P
[OPERATE] / [DRAWING]see LANG Windows Program LCAD
[OPERATE] / [OBJECTS] / [OBJECT DISPLAY]Button in vertical
toolbar or [Options] / [Parameters] / [Graphic parameters] /
[Object frame (with object number)]
[OPERATE] / [OBJECTS] / [SELECT OBJECT][Work on] / [Mark object
with mouse] or [Work on] / [Mark object with list] or button in
horizontal toolbar
[OPERATE] / [OBJECTS] / [SELECT POSITION]see LANG Windows
Program LCAD
[OPERATE] / [OBJECTS] / [ERASE][Work on] / [Delete marked data]
orDEL
[OPERATE] / [OBJECTS] / [COPY OBJECT][Work on] / [Multiposition
marked data]
[OPERATE] / [OBJECTS] / [INSERT OBJECT][Work on] /
[Multiposition marked data]
[OPERATE] / [OBJECTS] / [NEST OBJECTS]Not needed anymore
[OPERATE] / [OBJECTS] / [LINARZE OBJECTS]Not needed anymore
[OPERATE] / [OBJECTS] / [LAYER][Setup machine] / [Tools]
orButton in horizontal toolbar
[OPERATE] / [OBJECTS] / Change of position and size by
keyboard[Work on] / [Position/edit marked data]
[OPERATE] / [TEXT] / [CHARACTERSET][Construction] / [Text] /
[Font]
[OPERATE] / [TEXT] / [HEIGHT][Construction] / [Text] /
[Character height]
[OPERATE] / [TEXT] / [DIST.OF CHARACTERS][Construction] / [Text]
/ [Character spacing]
[OPERATE] / [TEXT] / [WIDTH][Construction] / [Text] / [Angle]
or[Construction] / [Text] / [Line width]
[OPERATE] / [TEXT] / [DISTORTION][Construction] / [Text] /
[Distortion factor]
[OPERATE] / [TEXT] / [ANGLE OF TEXT][Work on] / [Position/edit
marked data]
[OPERATE] / [TEXT] / [RAKE][Construction] / [Text] / [Slant]
[OPERATE] / [TEXT] / [RADIUS][Construction] / [Text] /
[Reference radius]
[OPERATE] / [TEXT] / [TEXTMODE][Construction] / [Text] /
[Reference radius left, middle, right]
[OPERATE] / [TEXT] / [REL.POSITION][Construction] / [Text] /
[Middle to middle char.]
[OPERATE] / [LIBRARY] / [SELECT LIBRARY][Construction] / [Object
from library / LG1-file] / [Library]
[OPERATE] / [LIBRARY] / [SAVE ELEMENT]Is dropped because
libraries cannot be generated in LTIRE any more.-> Save as
LG1-file and [Construction] / [Object from library / LG1-file] /
[Load object from LG1-file]
[OPERATE] / [LIBRARY] / [LOAD ELEMENT][Construction] / [Object
from library / LG1-file] / [Load object from LG1-file]
or[Construction] / [Object from library / LG1-file] / [Load object
from library] / [Select object] / [Info] / [Save LG1]
[OPERATE] / [LIBRARY] / [ERASE ELEMENT]Is dropped because
libraries cannot be generated in LTIRE any more.
[OPERATE] / [LIBRARY] / [CONTENT LIBRARY][Construction] /
[Object from library / LG1-file] / [Select object]
[OPERATE] / [ELEMENTS] / [LOAD ELEMENT][Construction] / [Object
from library / LG1-file] / [Load object from library]
[OPERATE] / [ELEMENTS] / [DELETE ELEMENT][Work on] / [Delete
marked data] orDEL or [Work on] / [Undo] (if the object to be
deleted has been created directly before)
[OPERATE] / [ELEMENTS] / [SELECT ELEMENT][Work on] / [Mark
object with mouse] or [Work on] / [Mark object with list] or button
in horizontal toolbar
[OPERATE] / [ELEMENTS] / [ELEMENT PARAMETER][Work on] / [Object
Info]
[OPERATE] / [ELEMENTS] / [ZERO ANGLE][Work on] / [Mold-data] /
[Zero angle of data]
[OPERATE] / [ELEMENTS] / [NORM IMAGE]Norm function of vertical
toolbar
[OPERATE] / [ELEMENTS] / [BASIC IMAGE][Work on] / [Mold-data] /
[Inner radius] and [Outer radius]
[OPERATE] / [ELEMENTS] / [LIB-DATA][Construction] / [Object from
library / LG1-file]
[OPERATE] / [ELEMENTS] / [RADIUS][Construction] / [Object from
library / LG1-file] / [Reference radius]
[OPERATE] / [ELEMENTS] / [WIDTH][Construction] / [Object from
library / LG1-file] / [Distortion X]
[OPERATE] / [ELEMENTS] / [HEIGHT][Construction] / [Object from
library / LG1-file] / [Distortion Y]
[OPERATE] / [ELEMENTS] / [ANGLE][Construction] / [Object from
library / LG1-file] / [Reference angle]
[OPERATE] / [ELEMENTS] / [ARC][Construction] / [Object from
library / LG1-file] / [Arc]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [PROJECTION FORM] /
[POLAR][Construction] / [Object from library / LG1-file] /
[Transformation] / [Polar]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [PROJECTION FORM] /
[XY-TILT][Construction] / [Object from library / LG1-file] /
[Transformation] / [XY-tilt]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [PROJECTION FORM] /
[XY][Construction] / [Object from library / LG1-file] /
[Transformation] / [XY-cartesian]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [PROJECTION FORM] /
[XY-POLAR][Construction] / [Object from library / LG1-file] /
[Transformation] / [X-cartesian Y-polar]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [PROJECTION FORM] /
[POLAR-XY][Construction] / [Object from library / LG1-file] /
[Transformation] / [X-polar Y-cartesian]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [REFERENCE
POINT][Construction] / [Object from library / LG1-file] /
[Reference angle (left, middle, right)]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [REFERENCE
RADIUS][Construction] / [Object from library / LG1-file] /
[Reference radius (bottom, middle, top)]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [PROJECTION-RADIUS
CORRECTION][Construction] / [Object from library / LG1-file] /
[Pos. of radius]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] /
[X0-POSITION][Construction] / [Object from library / LG1-file] /
[X0-Position]
[OPERATE] / [ELEMENTS] / [PARAMETER MENU] / [LIB
DISTORTION][Construction] / [Object from library / LG1-file] /
[Distortion X-Y]
[OPERATE] /[SCANNING][Setup machine] / [Scanning mold-surface]
or Ctrl+A
[OPERATE] /[SCANNING] [OUTER RAD.][Setup machine] / [Scanning
mold-surface] / [Outer radius]
[OPERATE] /[SCANNING] [OUTER HEIGHT][Setup machine] / [Scanning
mold-surface] / [Freelevel Z:]
[OPERATE] /[SCANNING] [STEP WIDTH][Setup machine] / [Scanning
mold-surface] / [Step width]
[OPERATE] /[SCANNING] [OFFSET][Setup machine] / [Scanning
mold-surface] / [Freelevel Z]
[OPERATE] /[SCANNING] [NEGATIVE LIMITING ANGLE][Setup machine] /
[Scanning mold-surface] / [Limit. angle negative]
[OPERATE] /[SCANNING] [POSITIVE LIMITING ANGLE][Setup machine] /
[Scanning mold-surface] / [Limit. angle positive]
[OPERATE] /[SCANNING] [TRACER SIZE][Setup machine] / [Scanning
mold-surface] / [Scanner length]
[OPERATE] /[SCANNING] [SCAN-FILENAME][Setup machine] / [Scanning
mold-surface] / [Load] or [Save]
[OPERATE] /[SCANNING] [START SCANNING][Setup machine] /
[Scanning mold-surface] / [Start scanning process]
[OPERATE] / [ADJUST][Setup machine] / [Setup] orCTRL+E]
[OPERATE] / [ADJUST] / [MANUAL CONTROL TABLE-, Y-, Z-,
W-AXIS][Setup machine] / [Setup] / [Manual mode Turntable, Y-, Z-,
W-axis]
[OPERATE] / [ADJUST] / [ABSOLUTE-POS][Setup machine] / [Setup] /
[Move absolute]
[OPERATE] / [ADJUST] / [RELATIVE-POS][Setup machine] / [Setup] /
[Move relative]
[OPERATE] / [ADJUST] / [CALIBRATE][Setup machine] / [Setup] /
[Calibrate]
[OPERATE] / [MACHINE][Setup machine] / [Edit machine
parameters]
[OPERATE] / [MACHINE] / [OFFSET][Setup machine] / [Edit machine
parameters] / [CTRL+O] (hidden menu)
[OPERATE] / [MACHINE] / [MACHINE OFFSET]Is not supported by
LTIRE anymore
[OPERATE] / [OUTPUT][Engraving] / [Engraving/milling mold]
orCTRL+G
[OPERATE] / [OUTPUT] / [OUTPUT COMPLETE][Engraving] /
[Engraving/milling mold] / [Engraving complete]
[OPERATE] / [OUTPUT] / [OUTPUT OBJECT][Engraving] /
[Engraving/milling mold] / [Engraving marked data]
[OPERATE] / [OUTPUT] / [OUTPUT START OBJECT][Engraving] /
[Engraving/milling mold] / [Engraving starting with marked
data]
[OPERATE] / [OUTPUT] / [CUTTER HEIGHT][Engraving] /
[Engraving/milling mold] / [Tool length]
[OPERATE] / [OUTPUT] / [NORM IMAGE]Norm function of vertical
toolbar
[OPERATE] / [MILL STAMP SHAFT][Engraving] / [Milling pocket]
or[Construction] / [Pocket]
Error messages during operationThis list contains only messages
that can occur during engraving on a LGT with MCG control. If you
have a Andron control (Servo, LTire 6 and 7) or you cannot find the
error number here, please have a look to the printed
documentation.Nr:Error description:Action by user:
900CS31-bus-system error!Check bus-wiring (60 Ohm), switching to
STOP and START again at SPS central unit K5, so that FK3-LED is off
afterwands.
901EMERGENCY-OFF!
902Air-conditioner fault (including overtemperature)!Look for
fault code at backside of air conditioner and call LANG-service;
emergency operation is possible with backside door open and
air-conditioner-ok-simulation!
903Air pressure too low! -> MCG STOPRestore air pressure
level!
904Spindle generator: RPM not ok!Look for smooth running of
spindle, check connectors at spindle and cabinet side.
905Spindle generator: RPM not 0!
906Overheat MCG or communication error!Look for clean MCG
cooling channel.
907Spindle generator: overload!Check condition of tool, milling
speed and smooth running of spindle.
908Spindle generator: overheat!(BMR only): Check function of
spindle cooler; check wiring of spindle cable.
90924V MCG not ok!Switch on MCG resp. check 24V/2A - fuse of
MCG
910Spindle cooler fault!Check control-lights of spindle
cooler.
911Spindle generator not ready!(S&M only, incl. overtemp.):
Check control-LED at spindle generator for overtemperature (LED PTC
is on).
912EMERGENCY-OFF-loop disconnected!Repair disconnection of
emergency-off-loop (primary).
913Line isolation not ok!
Only LGR:
914Low line voltage!Improve quality of line supply if this shows
up more often.
915Line phase seq. error or phase voltage LTool.txt /
LToolW.txt: The content of the tool library is used to create a
text file named LTool.txt (ANSI, LTire 5 and 6) / LToolW.txt
(Unicode, LTire 7) and is saved in the directory of the
application. This textfile can be loaded and printed with any text
program (for example Notepad). This printout serves as information
for already entered tools.Tool PreviewMeaningful static parameters
of a selected tool will be displayed as a drawing on the lower left
of the display screen. A double click to the drawing or the tool
list will enlarge (zoom) the display.Note: Top The displayed order
is not the sequence of the tools during engraving. Engraving always
starts with the lowest tool number. The dialog does not remember
the sorting order. When opening the dialog, the table is sorted by
the tool number. LTire 6 and 7: When taking over tool librarys that
were created with LTire 5 or lower, this value must be adapted
because the value was given in percentage of the maximum speed. The
feedrate can additionally be controlled with the poti federate and
Master/Rapid of the hand held control unit ( for operating the hand
held control unit see machine documentation). The feedrate value
entered in the tool library will be moved exactly, if in the dialog
Output in the group poti-settings the value for the movement- poti
Feedrate is 100% ( see also chapter 8.2 Engraving /milling mold). A
ball tool can not be used during cutter radius compensation for
corner clearing, otherwise the of workpiece becomes defective in
the corner areas. In that case the message Invalid tool will occur.
A cutter is a ball cutter if its ball radius is unequal 0.0.Tasks
What is to be noted when milling 3D ?The LTIRE program is capable
of reading 3D-LG1-files and transferring them to the machine. These
LG1-files may contain any contours, such as stamps, reliefs or data
projected on any surfaces for example.Procedure:- Load LG1-file-
State parameters for LG1-files-Setup tool- Start engravingThe
management of the passes is also active for 3D-data, i.e. during
the 3D-output it is also milled in layers, if a tool with pass has
been stated in the tool library.The max. depth of the 3D-engraving
can either be determined by the perspective depiction or in the
Object-Info-Dialog File: Open The file, selected in the file menu,
is loaded into the working memory of the current LTire-application.
Files in the format *.LG1 and *.LG2 can be loaded directly.
Depending on add-ons several other file formats can be imported, e.
g. HPGL, DXF and some more.If an LG1-file is chosen, which is not a
tire file from LCADR, a dialog for entering the Parameters for
LG1-files appears. This dialog appears when importing other
formats, too.Note: The file is completely loaded into the main
memory. I.e. there has to be enough memory available. The command
Load can be activated by the button in the horizontal toolbar. The
command Load is undone by the Undo-Function . When importing files,
the foreign format is converted to LG1 first. The progress of the
conversion is shown in the status bar. When importin files, it may
be usefull to sort and close contours.See also: Add a file Sort and
close selected contoursParameters for LG1-filesThis dialog appears
allways when importing data from foreign file formats. It appears
also when loading LG1-files, that are not from LCADR.Tool numberA
fix layer number can be assigned to the loaded contours.Radius for
engravingThis radius value in millimetres [mm] or [inch] will be
taken in account during the output, if the engraving mode is
defined as roll on surface. Up to the value of the radius the
radius is measured on the chord, afterwards the character will be
rolled on the surface. If the engraving mode is defined as project
on surface, the value of the radius is irrelevant.Engraving
modeRoll on the surfaceUp to the reference radius it is measured on
the chord, afterwards the object is rolled on the surface.Projected
(on surface)Vertical parallel projection: Every radius is measured
on the chord.Edit: Sort and close selected contoursWith this menu
item selected contours can be closed. The tolerance for closing can
be selected with the dialog 'Options' on the tab 'Close'. This
function can be very usefull when importing data from other file
formats like DXF.Options: ParametersThis dialog allows to modify
several parameters. It consists of the following tabs:
Working frameGraphicCloseResolutionClipboardVectorfilter
Working frame
A working area can be defined here.This working area is defined
by a rectangle and is supposed to display the working area of the
application. If frequently only a certain part of the side-wall is
processed, the working area can be defined for this section of the
side-wall. With the function Standardization to working frame only
this section of the side wall drawing is displayed. The working
area frame does not effect the engraving.Display working frameThe
working frame can be activated / inactivated here.
Graphic
Tool path simulationAll immerged motions of the cutter are drawn
with the equivalent cutter diameter. So it is easier to recognize,
whether the selected contour distance is correct or not. This
display mode can be enabled with from the vertical toolbar.BaseThe
drawing line width responds to the tip diameter (2 * tip radius) of
the tool on the bottom of engraving.
Surface of materialThe drawing line width results from the tool
radius (depending on tool geometry and immerging depth) on the
material surface.Draw drilling symbolWhen the checkmark is set, for
each drilling hole a small symbol will be displayed. When many
drilling holes are used the display can be very complex, so
sometimes it is easier to switch them off.Show positions
automaticallyWith this option, positions of selected contours will
be shown automatically without activating the function Display
position marks from the vertical toolbar.
Close
The tolerance for closing contours with the function Sort and
close selected contours can be entered here. See also: Sort and
close selected contours.
Resolution
Scroller resolutionStates the value by which the screen display
is shifted, in case of clicking on the horizontal or vertical
scroll bar.Spline resolutionDetermines the resolution of the
vectorising of a spline curve. The higher the value, the more
precise the curve is vectorised. Most of the time the spline
function is not used in LTIRE. Then this value is unimportant.
Clipboard
Within this page the engraving parameters for contours inserted
throught the clipboard are defined.Tool numberThis tool number will
be assigned to contours, regardless of possible layers.Radius for
engravingThis radius value in millimetres [mm] or [inch] will be
taken in account during the output, if the engraving mode is
defined as roll on surface. Up to the value of the radius the
radius is measured on the chord, afterwards the character will be
rolled on the surface. If the engraving mode is defined as project
on surface, the value of the radius is irrelevant.Roll onto
surfaceUp to the reference radius it is measured on the chord,
afterwards the object is rolled onto the surface.Parallel
projectionVertical parallel projection: Every radius is measured on
the chord.
Vectorfilter Top
The values for the vector filter can be entered here. The filter
consists of two parameters. A point will be filtered if one of the
parameters applies. The filter works on selected data or on all
data, if nothing is selected.
The actual function can be reached through the menu "Edit
vectors" | "Vector filter". In LTire 5 the data will be checked
automatically before engraving, when the values are unequal to 0.
This helps to avoid problems with the MCG, that can occur with
certain data. Smallest distanceEnter the smallest distance that may
occur inside the data. All points with a smaller distance will be
marked or deleted. A value of 0 disables this parameter. Smallest
turnaroundEnter the smallest turnaround that may occur inside the
data. The following picture illustrates the meaning of the angle
parameter:
The smaller the value, the smaller the turnaround. An angle of 0
means: there is no turnaround at all, i. e. the point lies on a
line between the surrounding points. A value of 0 disables this
parameter.See also: Vector filter
See also: Load parameters
Save parametersEdit: Selected object engraving parameterThis
dialog is not available any more. It is completely replaced by the
command edit | Object parameters.Parameters important for engraving
can be defined in this dialog box.Radius for engravingThis radius
value in millimetres [mm] or [inch] will be taken in account during
the output, if the engraving mode is defined as roll on surface. Up
to the value of the radius the radius is measured on the chord,
afterwards the character will be rolled on the surface. If the
engraving mode is defined as project on surface, the value of the
radius is irrelevant.Engraving modeRoll on the surfaceUp to the
reference radius it is measured on the chord, afterwards the object
is rolled on the surface.Projected (on surface)Vertical parallel
projection: Every radius is measured on the chord.See also: Change
tool assignment Object parameters Mold-data (Interior radius,
exterior radius)
[OCX EditCtrl]#-----------------------------------------------#|
G. Sagnes || Texte, die vom EditCtrl.ocx benutzt werden
|#-----------------------------------------------#[About EditCtrl
Control]Caption=About EditCtrl
Control00001=OK00234='00232=Copyright (C) 1998-2014, LANG GmbH
&& Co. KG00233=Unit definition for edit fields, use of
calculator-00001='-00001
[STRING_AREA:IDS]0003=Unit Property32778=EditCtrl-Failure, LANG
GmbH & Co. KG32779=Range Check! Minimum
Value~~Minimum32780=Range Check! Maximum Value~~Maximum32781=Range
Check!~~Range of values32782=Range Check!~~Range of
values32783=Parameter file of EditCtrl not found!~~Default
parameter file will be created.32784=Invalid parameter file path
from Lang32.dll! EditCtrl will not work properly.0004=Failed to
convert [%s] to Unicode file. Please close the program and contact
Lang support!
[Zeit]Caption=Time01007=[..............]01008=Unit
abbreviation01013=Unit of time00228=Define special unit for the
current edit field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01003=Select the time unit to be used...
[Laenge]Caption=Linear measure01007=[..............]01008=Unit
abbreviation01011=Unit of linear measure00228=Define special unit
for the current edit field00229=This unit corresponds to the
current edit field.-00228=This option allows an independent
unit~definition for each edit field.-01002=Select the length unit
to be used...
[Winkel]Caption=Angle01007=[..............]01008=Unit
abbreviation01012=Unit of angle00228=Define special unit for the
current edit field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01004=Select the angle unit to be used...
[Frequenz]Caption=Frequency01007=[..............]01008=Unit
abbreviation01016=Unit of frequency00228=Define special unit for
the current edit field00229=This unit corresponds to the current
edit field.-00228=This option allows an independent unit~definition
for each edit field.-01020=Select the frequency unit to be
used...
[Stromstaerke]Caption=Electric
current01007=[..............]01008=Unit abbreviation01014=Unit of
current00228=Define special unit for the current edit
field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01018=Select the electric current unit to be
used...
[el. Spannung]Caption=Voltage01007=[..............]01008=Unit
abbreviation01015=Unit of voltage00228=Define special unit for the
current edit field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01019=Select the electric voltage unit to be
used...
[Gewicht]Caption=Mass01007=[..............]01008=Unit
abbreviation01017=Unit of mass00228=Define special unit for the
current edit field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01006=Select the mass unit to be used...
[Flaeche]Caption=Square measure01007=[..............]01008=Unit
abbreviation01011=Unit of square measure00228=Define special unit
for the current edit field00229=This unit corresponds to the
current edit field.-00228=This option allows an independent
unit~definition for each edit field.-01002=Select the square unit
to be used...
[Volume]Caption=Cubic measure01007=[..............]01008=Unit
abbreviation01011=Unit of cubic measure00228=Define special unit
for the current edit field00229=This unit corresponds to the
current edit field.-00228=This option allows an independent
unit~definition for each edit field.-01002=Select the cubic unit to
be used...
[Lineargeschwindigkeit]Caption=Linear
speed01007=[..............]01008=Unit abbreviation01011=Unit of
linear measure01013=Unit of time00228=Define special unit for the
current edit field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01003=Select the time unit to be
used...-01002=Select the length unit to be used...
[Winkelgeschwindigkeit]Caption=Angle
Speed01007=[..............]01008=Unit abbreviation01012=Unit of
angle01013=Unit of time00228=Define special unit for the current
edit field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01003=Select the time unit to be
used...-01004=Select the angle unit to be used...
[Linearbeschleunigung]Caption=Linear
acceleration01007=[..............]01008=Unit abbreviation01011=Unit
of linear measure01013=Unit of time00228=Define special unit for
the current edit field00229=This unit corresponds to the current
edit field.-00228=This option allows an independent unit~definition
for each edit field.-01003=Select the time unit to be
used....-01002=Select the length unit to be used...
[Winkelbeschleunigung]Caption=Angle
acceleration01007=[..............]01008=Unit abbreviation01012=Unit
of angle01013=Unit of time00228=Define special unit for the current
edit field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01003=Select the time unit to be
used...-01004=Select the angle unit to be used...
[Dateigroesse]Caption=File size01007=[..............]01008=Unit
abbreviation01016=File size unit00228=Define special unit for the
current edit field00229=This unit corresponds to the current edit
field.-00228=This option allows an independent unit~definition for
each edit field.-01003=Select the file size unit to be used...
[Einheiteneigenschaften]Caption=Unit
Properties00001=OK00002=Cancel12321=&Apply00009=Help
[Laenge-Liste]00000=Micrometer [m]00001=Millimetre
[mm]00002=Centimetre [cm]00003=Decimetre [dm]00004=Metre
[m]00005=Kilometre [km]00006=Milli-inch [in./1000]00007=Inch
[in.]00008=Feet [ft.]00009=Yard [yds]
[Zeit-Liste]00000=Milliseconds [ms]00001=Seconds
[s]00002=Minutes [min]00003=Hours [h]
[Winkel-Liste]00000=Degrees [Deg.]00001=Radiant
[Rad]00002=Rotation [U]
[Frequenz-Liste]00000=Hertz [Hz]00001=Kilohertz
[kHz]00002=Megahertz [MHz]
[eStrom-Liste]00000=Milliampere [mA]00001=Ampere [A]
[eSpannug-Liste]00000=Volts [V]00001=Kilovolts [kV]
[Gewicht-Liste]00000=Grammes [g]00001=Kilogrammes
[kg]00002=Pounds [lb]
[Datei-Liste]00000=Bytes [byte]00001=Kilobytes
[kB]00002=Megabytes [MB]00003=Gigabytes [GB]00004=Terabytes
[TB]
[EditCtrl-Popupmenu]Text-&032771=UndoText-&032772=CutText-&032773=CopyText-&032774=PasteText-&032775=DeleteText-&032776=Select
allText-&032777=Properties
[STRING_AREA:STRING]
[Credits]Caption=Credits00001=OK01002=Static-00001='-00001
Construction: Load object from library / LG1- file Load object
from library / LG1-file:Implies, whether a library (*.LIB) made in
LCADR, or an LG1-file (*.LG1) should be used as data
source.Radius:Radius in [mm], which defines the position [bottom] /
[middle] / [top] of an object. This reference radius is taken into
account for the output. The radius is measured on the chord up to
the reference radius. If the output mode is switched on , the sign
will be 'rolled on the surface' afterwards. If the reference radius
is changed, the arc is changed as well.Angle:Angle in [degrees] at
which the object is arranged on the side-wall drawing [left] /
[right] / [cenred]. If the reference angle is changed, the arc
changes as well.Arc:The arc is the measure between the angle 0 and
the given reference angle on the reference radius in [mm]/[inch].
I.e. the arc depends directly on the reference radius and the
reference angle. If the arc changes, the reference angle changes as
well.Transformation:1: Polar The signs are arranged fan-like
towards the center of the tire.The given width is reached at the
lower edge of the sign, i.e. at the upper edge the transformed
signs are wider than the original signs. Since many points have to
be added because of the curvation, the amount of data increases
compared with the original data.
2: XY-tilt Here the single signs are displayed cartesian
(upright). However each sign is tilted, so that the sign lower edge
runs vertical to the sign reference angle. That means, the
reference angle changes from one sign to the next one. This
transformation is suitable especially for the depiction of texts.
Since no points have to be inserted, the amount of data does not
increase compared with the original data.
3: XY-cartesian Here the complete object is displayed cartesian
(upright). This kind of transformation is suitable especially for
the depiction of logos. Since no points have to be inserted, the
amount of data does not increase compared with the original
data.
4: X-polar Y-cartesian A merging of polar and cartesian. The
signs are displayed polar (fan-like) in X-direction, while the
Y-direction remains unchanged cartesian (upright).
5: X-cartesian Y-polar Merging of cartesian and polar. The
X-direction remains cartesian (upright), while the Y-direction is
displayed polar (fan-like).Engraving mode:
(1) Roll on surface:During the output of data to the machine it
is measured up to the reference radius on the chord. Afterwards the
object is 'rolled' on the surface of the tire sidewall.
(2) Project on surface:Vertical parallel projection: all radii
are measured on the chord.
Position of radius:
Center of symbol:The center of the rectangle enclosing the
object is put on the reference radius.
Corner points:The corner points of the rectangle enclosing the
object are put on the reference radius. If very wide and very
narrow signs ars placed directly next to each other, an optically
more beautiful image will be generated by the function corner
points. This can be seen especially on the letter combinations 'Hi'
and 'Mi'
(graphic)X0-Position:Here it is defined, whether a negative
X0-value of a library object is to be taken into account when
loading on a tire side-wall.
X0 = 0.0:The left X-position (X0) is always set on the value
0.0[mm]/[inch].
From library:A poss. existing negative X0-position is
maintained. A shift of the zero point can be carried out by this
function.
(graphic)Distortion X:Factor of distortion for the library
object in X-direction.Distortion Y:Factor of distortion for the
library object in Y-direction.Tool no. from library:Defines,
whether a tool number is to be adopted from the library. Should a
new number be assigned to the data, the new number is to be entered
into the entry panel tool number. Note, that the new tool number
must be assigned to the entire object, even if several tools from
the library are assigned to the object.Should a library from LCADR
(*.LIB) serve as data source, the library and the wanted object
from the library can be chosen with the following two
functions.Library:A library (*.LIB) is selected.Select object:An
object from the library chosen before is selected.If an LG1-file
(*.LG1) serves as data sourec, the following 3 functions are
available:Create LG1-file: Several LG1-files are summarized.Select
LG1-file:An already existing LG1-file is selected.->
Info:Information about th selected LG1-files are shown.The command
Load object from library / LG1-file can be undone by the
Undo-function .
The file, selected in the file menu, is loaded into the working
memory of the current LTire-application. Files in the format *.LG1
and *.LG2 can be loaded directly. Depending on add-ons several
other file formats can be imported, e. g. HPGL, DXF and some
more.If an LG1-file is chosen, which is not a tire file from LCADR,
a dialog for entering the Parameters for LG1-files appears. This
dialog appears when importing other formats, too.Note: The file is
completely loaded into the main memory. I.e. there has to be enough
memory available. The command Load can be activated by the button
in the horizontal toolbar. The command Load is undone by the
Undo-Function . When importing files, the foreign format is
converted to LG1 first. The progress of the conversion is shown in
the status bar. When importin files, it may be usefull to sort and
close contours.See also: Add a file Sort and close selected
contoursFiierul, selectat n meniul File, este ncrcat n memoria de
lucru a actualului LTire-cererii. Fiiere n format * .LG1 i * .LG2
pot fi ncrcate direct. n funcie de o serie de alte formate de
fiiere de suplimente pot fi importate, e. g. HPGL, DXF i ceva mai
mult.
n cazul n care un LG1-fiier este ales, care nu este un fiier de
anvelope de la LCADR, apare o fereastr de dialog pentru
introducerea parametrilor de LG1-fiiere. Acest dialog apare atunci
cnd import alte formate, de asemenea.
Not:Fiierul este complet ncrcat n memoria principal. Adic
trebuie s existe suficient memorie disponibil.Comanda LOAD poate fi
activat prin butonul din bara de instrumente orizontal.Comanda LOAD
este anulat de ctre Anulare-Function.La importul de fiiere,
formatul strin este convertit la LG1 primul. Progresul a conversiei
este afiat n bara de stare.Cnd importin fiiere, poate fi util
pentru a sorta i contururi aproape.
Vezi si:Adaug un fiierSortare i contururi aproape selectate
Edita parametrii de ieire (LTire 6 i 7)Mod de operare
GravurAcest mod este modul standard pentru funcionarea 4-axe.
Deoarece nu exist nici un ferstru-mode pentru LGT-S, nici un alt
mod poate fi selectat aici.
Parametrii
Lungime instrumentLungimea tietor este gradul de centrul axei de
rotaie a vrfului tietor n [mm]. Aceast msur trebuie s fie foarte
exact, pentru c n caz contrar poziia axei nu vor fi calculate
exact.
Pentru maini cu un sistem de msurare electronic aceast msur este
calculat automat atunci cnd maina a atins punctul de msurare
(lungime instrument msurat electronice).
Pentru mainile fr sistem de msurare electronic aceast msur
trebuie s fie determinat ct mai exact i a intrat n aceast poziie
sau n meniul de ieire.
ProcesSchimbare instrumentn cazul n care bif "schimbarea
instrument Manual" este setat, schimbtorul instrument nu vor fi
folosite n timpul gravura. Instrumentele trebuie s fie aplicate
manual la cerere.Scufundarea compensateScula de tiere se mic repede
pe materialul de la nlime (nlimea de securitate) presetat n condiii
de siguran. Pentru Scufundat de tiere n material, cutter mut primul
la sumberging compensa cu vitez mare. De acolo mai departe,
dispozitivul de tiere s fie alimentat n piesa de prelucrat la
avansul.
Max. acceleraie plac turnant (LTire 7)Proprietile de accelerare
ale platan trebuie s fie echilibrate mpotriva greutatea peretelui
lateral. Reduce acceleraia maxim pentru pereii laterali de greutate
inaltime. Smuls este reglat automat.
Pentru a instrumentelorOrdine inversDe obicei LTire utilizeaz
instrumentele n ordine cresctoare. n primul rnd conturul cu cel mai
mic numr instrument va fi inscripionat, atunci va fi utilizat
urmatorul numar mai mare etc.n cazul n care caseta este bifat,
instrumentele vor fi utilizate n direcia invers. Aceast opiune ar
trebui s fie folosite numai, n cazul n care biblioteca instrument
este construit pentru asta.
Controlul vitezei
Pentru a realiza un moment gravur scurt, poteniometre pot fi
dezactivate. Cu aceast opiune timpul de comutare intrrile pot fi
omise. n cazul n care este bifat caseta, doar Poti de master este
activ.Pentru a evita un instrument poart n timp ce potis sunt
dezactivate, un factor de vitez pentru scufundarea pot fi
introduse. Valoarea implicit pentru acest factor este de 30%;
aceasta poate varia ntre 5 i 100%.
CompensaPlac turnantPot fi introduse aici pentru platan o
compensare ax. Poziia axei va fi mutat matematic (nu mecanic) de
valoarea introdus. Offset-R pot fi utilizate pentru ajustarea
mucegai anvelope pe platan.Un alt, posibilitate uneori mai uor de
reglare se poate face prin schimbarea datelor n date Mold
dialog.
Controlul Break instrument
Dac funcia de control break instrument este activat, fiecare
instrument se msoar din nou dup ce este folosit. Rezultatele
fiecrei msurtori sunt comparate nainte instrumentul este pus n
funciune i n cazul n care o diferen n lungime, n plus fa de
tolerana dat este determinat, se presupune c maina este rupt.
ActivCnd check-marca este setat aici, controlul pauz este
activ.
ToleranValoarea de toleran poate fi setat aici.
Pe instrument ruptn funcie de ce opiune a fost selectat n
meniurile caseta list, aparatul fie se oprete dup ce instrumentul a
fost msurat, sau continu operaiunea gravura dup toolchange jos.
Ultimul protocoln timpul procesului de gravur, LTire creeaz un
protocol, n care toate instrumentele sparte sunt listate separat.
Pentru a putea compara informaiile din acest jurnal cu cele
coninute n jurnalul anterior, putei s facei clic pe acest buton.Dup
gravur este completat
Sta nemicat n nlime poziionareDup terminarea procesului de
masina iese din material i se oprete la aceast poziie.
Mutare Z-axa de 100 [mm] pnDup finalizarea procesului de
aparatul iese din materialul ce se deplaseaza pe 100 [mm], prin axa
Z, similar cu stop.
Mutare n poziia de parcareDup terminarea gravura aparatul iese
din material i se mut n poziia de parcare, nfiinat n meniul
Setup.
Instrument de control de viaCnd "Active Control" este setat,
LTire efectueaz o schimbare instrument din cauza instrument timp de
via, chiar i atunci cnd dispozitivul de tiere este n interiorul
materialului. Pentru a gsi posturi optime pentru o schimbare
instrument este necesar s aib o gam de cutare pentru poziiile din
afara materialul. Implicit pentru valoarea de toleran este de
5%.
Not:
n cazul n care controlul de via instrument este activ, LTire
solicit, n anumite circumstane pentru mai multe instrumente, n caz
contrar durata de via instrument va fi depit.Dac viaa instrument
este depit, un nou instrument va fi solicitat sau luate de la
schimbtorul de instrument. Dup msurarea funciei, LTire deplaseaz
exact n poziia n care unealta precedent oprit. Noul instrument se
deplaseaz direct n materialul, indiferent de un potenial strategie
n curs de dezvoltare.
