IEC TEST REPORT FORM TEMPLATE - BitGravityasrock.pc.cdn.bitgravity.com/TSD/PEGA/JPT/DOC/CB/Jupiter... · Copy of marking plate The artwork below may be only a draft. ... Beitou District,

TÜ V SÜ D Asia Ltd. Taiwan Branch Report reference No.: 081-150833-100

7F., No. 37, Sec. 2, Zhongyang S. Rd., JPTxxxxxxxxxxxxxxx-M1.DOC

Beitou District, Taipei City, 11270, Taiwan Page 1 of 26 Test Report IEC60950_1F

Test Report issued under the responsibility of:

NCB TÜ V SÜ D PSB Pte Ltd

1 Science Park Drive,

Singapore 118221

TEST REPORT

IEC 60950-1

Information technology equipment – Safety –

Part 1: General requirements

Report Number. .............................. : 081-150833-100

Date of issue ..................................... : 2015-12-03

Total number of pages ...................... 26

Applicant’s name ............................ : PEGATRON Corporation

Address ............................................ : 5F, No.76, Ligong St., Beitou District, 112 Taipei, TAIWAN

Test specification:

Standard ........................................... : IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am 2:2013

Test procedure ................................. : CB Scheme

Non-standard test method…………..: N/A

Test Report Form No. ..................... : IEC60950_1F

Test Report Form(s) Originator ........ : SGS Fimko Ltd

Master TRF....................................... : Dated 2014-02

Copyright © 2014 IEC System of Conformity Assessment Schemes for Electrotechnical Equipment

and Components (IECEE System). All rights reserved.

This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.

If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed.

This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory

and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02..

General disclaimer:

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report.




Test item description ..................... : PC

Trade Mark ...................................... :

Manufacturer .................................. : Same as applicant.

Model/Type reference .................... : Jupiter, JPTxxxxxxxxxxxxxxx ("x" can be any alphanumeric character including blank or "-" or "/" for marketing use only.)

Ratings ............................................ : 19 Vdc, 3.42 A or 4.74 A or 6.32 A




Testing procedure and testing location:

CB Testing Laboratory: TÜ V SÜ D Asia Ltd. Taiwan Branch

Testing location/ address ............................ : 7F., No.37, Sec. 2, Zhongyang S., Rd., Beitou District, Taipei City, 11270, TAIWAN

Associated CB Testing Laboratory: N/A

Testing location/ address ............................ : N/A

Tested by (name + signature) ...................... : Mr. Ralph Lai

Approved by (name + signature) ................. : Mr. Owen Hsu

Testing procedure: TMP/CTF Stage 1: N/A


Tested by (name + signature) ...................... :

Approved by (name + signature) ................. :

Testing procedure: WMT/CTF Stage 2: N/A



Witnessed by (name + signature) ................ :


Testing procedure:

SMT/CTF Stage 3 or 4:

N/A



Witnessed by (name + signature) ................ :


Supervised by (name + signature) .............. :




List of Attachments (including a total number of pages in each attachment):

Original Test Report No.:

Attachment No. 1

081-150833-000

National and Group Differences

57

30

pages

pages

+

72

pages attachments

Attachment No. 2 Marking Plate 2 pages

Attachment No. 3 Photo 6 pages

Summary of testing:

Tests performed (name of test and test clause):

All test results were found satisfactory in accordance with IEC 60950-1:2005 (2

nd Edition) +

A1: 2009 + A2:2013 and EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013

Testing location:

All tests as described in Test Case and Measurement Sections were performed at the laboratory described on page 3.

Summary of compliance with National Differences:

List of countries addressed

According to CB Bulletin, the National Differences include Australia (AU), Canada (CA), China (CN),

Germany (DE), Israel (IL), Korea (KR), Switzerland (CH) and United States of America (US). Group

Differences (CENELEC COMMON MODIFICATIONS) as listed in the European Standard are recorded in

this Report.

THE PRODUCT FULFILS THE REQUIREMENTS OF IEC 60950-1:2005 + A1: 2009 + A2:2013 and EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013

Copy of marking plate

The artwork below may be only a draft. The use of certification marks on a product must be

authorized by the respective NCBs that own these marks.

See attachment No. 2 of Test Report Ref. No.: 081-150833-000 and attachment No. 2 of Test Report Ref. No.: 081-150833-100.




Test item particulars ................................................... :

Equipment mobility.................................................: [X] movable [] hand-held [] transportable [] stationary [] for building-in [] direct plug-in

Connection to the mains........................................: [] pluggable equipment [] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord

[X] not directly connected to the mains

Operating condition................................................: [X] continuous [] rated operating / resting time:

Access location ......................................................: [X] operator accessible [] restricted access location

Over voltage category (OVC) ................................: [] OVC I [] OVC II [] OVC III [] OVC IV

[X] other: not directly connected to AC or DC mains.

Mains supply tolerance (%) or absolute mains

supply values .........................................................:

+10 %, -10 %

Tested for IT power systems .................................: [] Yes [X] No

IT testing, phase-phase voltage (V) ......................: 230 V (for Norway)

Class of equipment ................................................: [] Class I [] Class II [X] Class III [] Not classified

Considered current rating of protective device as

part of the building installation (A) .......................:

N/A

Pollution degree (PD) .............................................: [] PD 1 [X] PD 2 [] PD 3

IP protection class ..................................................: Ordinary

Altitude during operation (m) ................................: Up to 2000

Altitude of test laboratory (m) ...............................: below 2000

Mass of equipment (kg) .........................................: Approx. 1.17 (without stand)

Approx. 1.26 (with stand)

Possible test case verdicts:

- test case does not apply to the test object ........... : N/A

- test object does meet the requirement .................. : P (Pass)

- test object does not meet the requirement ........... : F (Fail)

Testing .......................................................................... :

Date of receipt of test item ......................................... : 2015-11-23

Date (s) of performance of tests ............................... : 2015-11-23 to 2015-11-30




General remarks:

"(See Enclosure #)" refers to additional information appended to the report.

"(See appended table)" refers to a table appended to the report.

Throughout this report a comma / point is used as the decimal separator.

Manufacturer’s Declaration per sub-clause 4.2.5 of IECEE 02:

The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided.................................................................:

Yes

Not applicable

When differences exist; they shall be identified in the General product information section.

Name and address of factory (ies) .......................... :

MAINTEK Computer (Suzhou) Co., Ltd. (ID No.: 51922)

233, Jin Feng Road, Suzhou New District, 215011 Jiangsu, PEOPLE'S REPUBLIC OF CHINA




Report No. < 081-150833-100 >

The modification for this report is to:

1) Replace and evaluate the National and Group Differences for Canada and United Kingdom (listed in Clause 4.3.6 in the European Standard). See attachment No. 1 of Test Report Ref. No.: 081-150833-100 for details.

2) Add alternate motherboard H110-P1, see motherboard difference table and table 1.5.1 for details.

3) Add system rating 19 Vdc, 3.42 A and 19 Vdc, 6.32 A for different CPU rating, see motherboard difference table for details.

4) Add alternate Power Adapter source, see table 1.5.1 for details.

5) Add alternate enclosure construction B, which is similar to original except for front bezel and add openings, see table 4.6.1 & 4.6.2 and attachment photo for details.

6) The equipment provided optional VESA Mount bracket, see attachment photo for details.

7) Test Clause 5.1 Touch current and protective conductor current, due to client request, see Clause 5.1 and Table 5.1 for details.

8) Change model name, from JPTxxxxx to JPTxxxxxxxxxxxxxxx.

For the above described modification the following Testing were considered to be necessary:

S/N Testing Remark/Comments Verdict

1. Clause 1.7 Marking and instructions P

2. Clause 4.2 Mechanical strength P

3. Clause 5.1 Touch current and protective conductor current

(Client request)

N/A

4. Table 1.5.1 List of critical components P

5. Table 1.6.2 Electrical data (in normal conditions) P

6. Table 2.5 Limited power sources P

7. Table 4.5 Thermal requirements P

8. Table 4.6.1 & 4.6.2 Enclosure openings P

9. Table 5.1 Touch current measurement

(Client request)

N/A

10. Table 5.3 Fault condition tests P




General product information:

The equipment is a PC classified as information technology equipment. All models are identical except for model designations.

In models JPTxxxxxxxxxxxxxxx, "x" can be any alphanumeric character including blank or "-" or

"/" for marketing use only.

There are two alternate enclosure construction A or B, which are similar except for front bezel and

add openings, see table 4.6.1 & 4.6.2 and attachment photo for details.

The equipment provided optional VESA Mount bracket, see attachment photo for details. The external adapter is a CB certified device, see appended table 1.5.1 for details. The maximum ambient temperature specified by manufacturer is 40 °C.

There are three system rating and three alternate motherboard Q170-P1, B150-P1 and H110-P1, all

motherboards are similar except for some differences, see below table for the differences:

Motherboard Q170-P1 B150-P1 H110-P1

Rear USB ports USB 3.0*4

USB 3.0*2, USB 2.0*2

USB 3.0*4

System rating 19 Vdc, 6.32 A

or

12 Vdc, 4.74 A

19 Vdc, 6.32 A

or

12 Vdc, 4.74 A

19 Vdc, 3.42 A

or

12 Vdc, 4.74 A

Adapter 90 W 120 W 90 W 120 W 65 W 90 W

CPU 35 W 65 W 35 W 65 W 35 W 65 W

All tests were performed on model Jupiter to represent the other similar models.

Abbreviations used in the report:

- normal conditions N.C. - single fault conditions S.F.C

- functional insulation OP - basic insulation BI

- double insulation DI - supplementary insulation SI - between parts of opposite

polarity BOP - reinforced insulation RI

Indicate used abbreviations (if any)

IEC 60950-1

Clause Requirement + Test Result - Remark Verdict




1.7 Marking and instructions P

1.7.1 Power rating and identification markings See below. P

1.7.1.1 Power rating marking See below. P

Multiple mains supply connections..........................: No connection to the mains. N/A

Rated voltage(s) or voltage range(s) (V) ............... : 19 Vdc. P

Symbol for nature of supply, for d.c. only ............... : P

Rated frequency or rated frequency range (Hz) .... : DC Source. N/A

Rated current (mA or A) ........................................ : 3.42 A or 4.74 A or 6.32 A P

1.7.1.2 Identification markings See marking plate. P

Manufacturer’s name or trade-mark or identification mark ...................................................................... :

Trade-mark: PEGATRON P

Model identification or type reference .................... : Jupiter, JPTxxxxxxxxxxxxxxx ("x" can be any alphanumeric character including blank or "-" or "/" for marketing use only.)

P

Symbol for Class II equipment only ....................... : Class III equipment. N/A

Other markings and symbols ................................ : Additional symbols or markings that do not give rise to misunderstand.

P

1.7.1.3 Use of graphical symbols P

1.7.2 Safety instructions and marking See below for details. P

1.7.2.1 General The safety instruction contains

information for installation,

servicing, transport, storage

and technical data.

No other special installation

instruction required as the

equipment is class III.

P

1.7.2.2 Disconnect devices N/A

1.7.2.3 Overcurrent protective device N/A

1.7.2.4 IT power distribution systems Only SELV inside, no

connection to mains.

N/A

IEC 60950-1





4.2 Mechanical strength P

4.2.10 Wall or ceiling mounted equipment; force (N) .......: The equipment provided optional VESA Mount bracket.

Weight of the equipment: 1.17 kg (without stand) Force applied: 5.1 kg (50 N).

The mounting means withstood the force applied without breaking or damaging the mounting bracket, its securing means, or that portion of the unit to which it was attached.

P

IEC 60950-1





5.1 Touch current and protective conductor current N/A

5.1.1 General Class III equipment.

However, test for accessible

parts due to client request.

(see appended table 5.1).

N/A

5.1.2 Configuration of equipment under test (EUT) N/A

5.1.2.1 Single connection to an a.c. mains supply N/A

5.1.2.2 Redundant multiple connections to an a.c. mains

supply

N/A

5.1.2.3 Simultaneous multiple connections to an a.c. mains

supply

N/A

5.1.3 Test circuit N/A

5.1.4 Application of measuring instrument N/A

5.1.5 Test procedure N/A

5.1.6 Test measurements N/A

Supply voltage (V) ................................................ :

Measured touch current (mA) .............................. :

Max. allowed touch current (mA) .......................... :

Measured protective conductor current (mA) ....... :

Max. allowed protective conductor current (mA) ... :

5.1.7 Equipment with touch current exceeding 3,5 mA N/A

5.1.7.1 General ................................................................. : N/A

5.1.7.2 Simultaneous multiple connections to the supply N/A

5.1.8 Touch currents to telecommunication networks and

cable distribution systems and from

telecommunication networks

N/A

5.1.8.1 Limitation of the touch current to a

telecommunication network or to a cable

distribution system

N/A

Supply voltage (V) ................................................ :

Measured touch current (mA) .............................. :

Max. allowed touch current (mA) .......................... :




1.5.1 TABLE: List of critical components P

Object/part No. Manufacturer/ trademark

Type/model Technical data Standard (Edition / year)

Mark(s) of conformity

1)

Add alternate components:

Power Adapter Chicony Power

Technology Co.,

Ltd.

A15-120P1A I/P:

100-240 Vac,

50-60 Hz, 2.0 A

O/P:

19 Vdc, 6.32 A,

40 C, Class I

IEC 60950-1:

2005+A1+A2

(Additionally

evaluated to EN

60950-1:

2006+A11:

2009+A1:

2010+A12:2011+

A2: 2013)

CB by TUVRh

Chicony Power

Technology Co.,

Ltd.

A15-090P1A I/P:

100-240 Vac,

50-60 Hz, 1.2 A

max.

O/P:

19 Vdc, 4.74 A,

40 C, Class I

IEC 60950-1:

2005+A1+A2

(Additionally

evaluated to EN

60950-1:

2006+A11:

2009+A1:

2010+A12:2011+

A2: 2013)

CB by TUVRh

Chicony Power

Technology Co.,

Ltd.

A11-065N1A I/P:

100-240 Vac,

50-60 Hz, 1.7 A

max.

O/P:

19 Vdc, 3.42 A,

40 C, Class I

IEC 60950-1:

2005+A1+A2

(Additionally

evaluated to EN

60950-1:

2006+A11:

2009+A1:

2010+A12:2011+

A2: 2013)

CB by TUVRh

Delta Electronics,

Inc.

ADP-120RH D,

ADP-120RH B

I/P:

100-240 Vac,

50-60 Hz, 2 A

max.

O/P:

19 Vdc, 6.32 A,

40 C, Class I

IEC 60950-1:

2005+A1+A2

(Additionally

evaluated to EN

60950-1:

2006+A11:

2009+A1:

2010+A12:2011+

A2: 2013)

CB by UL

Delta Electronics,

Inc.

ADP-65JH BB,

ADP-65JH DB,

ADP-65MH B,

ADP-65JH HB,

I/P:

100-240 Vac,

50-60 Hz, 1.5 A

max.

O/P:

19 Vdc, 3.42 A,

40 C, Class I

IEC 60950-1:

2005+A1+A2

(Additionally

evaluated to EN

60950-1:

2006+A11:

2009+A1:

2010+A12:2011+

A2: 2013)

CB by TUVRh








1)

Motherboard -- H110-P1 -- -- --

- RTC Battery Vic Dawn

Enterprise Co Ltd

(KTS)

CR2032 3 Vdc, max.

abnormal

charging current

10 mA

UL 1642 UL

Jhih Hong

Technology Co

Ltd

CR2032 3 Vdc, max.

abnormal

charging current

10 mA

UL 1642 UL

SHUN WO NEW

POWER

BATTERY

TECHNOLOGY

LTD

CR2032 3 Vdc, max.

abnormal

charging current

10 mA

UL 1642 UL

Panasonic

Corporation,

Panasonic

Corporation of

North America

CR2032 3 Vdc, max.

abnormal

charging current

10 mA

UL 1642 UL

Interchangeable CR2032 3 Vdc, maximum

abnormal

charging current

5 mA min.

UL 1642 UL

- PTC

Polyswitch

(M1F3) provided

for Display port,

(M1F1) provided

for HDMI or

Display port,

(VF1) provided

for VGA port use

Littelfuse Inc. 0805L110ULXX

YYYYY (X can

be A-Z, 0-9 or

blank, Y can be

A-Z, 0-9 or

blank)

6 Vdc, 1.1 A EN 60738-1,

EN 60738-1-1,

EN 60730-1

TUVRH

Polytronics

Technology Corp.

SPR-P110 6 Vdc, 1.1 A EN 60738-1,

EN 60738-1-1,

EN 60730-1

TUVRH








1)

- PTC

Polyswitch (UF3,

UF11, UF12,

UF13) provided

for USB ports

use

Littelfuse Inc. 0805L260ULTH

XXYYYY (X can

be A-Z, 0-9 or

blank, Y can be

A-Z, 0-9 or

blank)

6 Vdc, 2.6 A EN 60738-1,

EN 60738-1-1,

EN 60730-1

TUVRH

Polytronics

Technology Corp.

SPR-P260T 6 Vdc, 2.6 A EN 60738-1,

EN 60738-1-1,

EN 60730-1

TUVRH

-PCB Interchangeable Interchangeable V-1 min.,

min. 105 C

UL 796 UL

Supplementary information:

1) Provided evidence ensures the agreed level of compliance. See OD-CB2039.




1.6.2 TABLE: Electrical data (in normal conditions) P

U (Vdc) I (A) Irated (A) P (W) Fuse # Ifuse (A) Condition/status

Motherboard: Q170-P1 (CPU 65W)

Power Adapter: Delta / ADP-120RH D, O/P: 19Vdc, 6.32A

19 4.43 6.32 84.17 -- -- Maximum Normal Load


Power Adapter: Delta / ADP-90MD H, O/P: 19Vdc, 4.74A


Motherboard: B150-P1 (CPU 65W)



Motherboard: B150-P1 (CPU 35W)



Motherboard: H110-P1 (CPU 65W)




Power Adapter: Chicony / A11-065N1A, O/P: 19Vdc, 3.42A



Maximum Normal Load:

The unit reads and writes in HDD operating continuously. Each USB port is loaded with 4.5W, run CPU program until performance to 100%. Brightness max.




2.5 TABLE: Limited power sources P

Circuit output tested:

Note: Measured Uoc (V) with all load circuits disconnected:

Components Sample No. Uoc (V) Isc (A) VA

Meas. Limit Meas. Limit

Motherboard: H110-P1

VGA(J69),Pin9 to GND, Normal condition, Protected by VF1

001 5.20Vdc 1.3 ≤8 5.65

(1.3Ax4.35V) ≤100

VGA(J69),Pin1-8,10-17 to GND, Normal condition

001 0Vdc 0 ≤8 0 ≤100

HDMI(J124),Pin 18 to GND, Normal condition, Protected by M1F1

001 5.20Vdc 1.4 ≤8 6.16

(1.4Ax4.40V) ≤100

HDMI(J124),Pin1-17,19 to GND, Normal condition

001 0Vdc 0 ≤8 0 ≤100

DP(J125),Pin 20 to GND, Normal condition, Protected by M1F3

001 3.31Vdc 1.7 ≤8 4.25

(1.7Ax2.50V) ≤100

DP(J125), Pin 1-19 to GND, Normal condition

001 0Vdc 0 ≤8 0 ≤100

SS USB1(J143),Pin1,10 to GND, Normal condition, Protected by UF12

001 5.20Vdc 3.1 ≤8 12.61

(3.1Ax4.07V) ≤100









SS USB1(J143),Pin2-9,11-18, to GND, Normal condition

001 0Vdc 0 ≤8 0 ≤100

SS USB1(J139),Pin1,10 to GND, Normal condition, Protected by UF11

001 5.20Vdc 3.2 ≤8 12.28

(3.2Ax3.84V) ≤100

SS USB1(J139),Pin2-9,11-18, to GND, Normal condition

001 0Vdc 0 ≤8 0 ≤100

F SS USB1(J156),Pin1,10 to GND, Normal condition, Protected by UF3

001 5.20Vdc 3.1 ≤8 12.09 (3.1Ax3.90V)

≤100

F SS USB1(J156),Pin2-9,11-18, to GND, Normal condition

001 0Vdc 0 ≤8 0 ≤100

F SS USB1(J151),Pin1,10 to GND, Normal condition, Protected by UF13

001 5.20Vdc 3.2 ≤8 12.12

(3.2Ax3.79V) ≤100









F SS USB1(J151), Pin2-9,11-18, to GND, Normal condition

001 0Vdc 0 ≤8 0 ≤100

RJ-45(J8),Pin1-8, to GND, Normal condition

001 0Vdc 0 ≤8 0 ≤100

supplementary information:




4.5 TABLE: Thermal requirements P

Supply voltage (V) .......................... : See beow.

Ambient Tmin (C) ............................ : --

Ambient Tmax (C) ............................ : --

Maximum measured temperature T of part/at: T (C) Allowed

Tmax (C)



Enclosure construction B

Test condition: 19 Vdc, Horizontal

19 Vdc, Vertical (with stand)

--

PCB near CPU 75.8 72.2 105

PTC 53.2 47.8 85

RTC 67.3 70.8 100

WiFi card body 71.2 59.1 95

SSD card body 69.0 65.8 95

RAM card body 40.0 40.0 95

Heatsink 67.7 49.2 70

CPU fan 50.9 47.2 70

HDD body 55.5 50.2 70

Enclosure outside (metal) near CPU 52.4 49.4 70

Ambient (Actual ambient before shift)

40.0 (27.9)

40.0 (28.2)

--


During test, all opening blocked except rear side openings.




4.5 TABLE: Thermal requirements P

Supply voltage (V) .......................... : See beow.

Ambient Tmin (C) ............................ : --

Ambient Tmax (C) ............................ : --

Maximum measured temperature T of part/at: T (C) Allowed

Tmax (C)




Test condition: 19 Vdc, Horizontal

19 Vdc, Vertical (with stand)

--

PCB near CPU 64.2 60.8 105

PTC 56.0 53.2 85

RTC 56.9 54.1 100

WiFi card body 62.3 59.7 95

SSD card body 60.4 57.5 95

RAM card body 40.0 40.0 95

Heatsink 62.0 59.3 70

CPU fan module 55.1 52.9 70

HDD body 50.3 48.5 70

Enclosure outside (metal) near CPU 48.1 46.5 70

Ambient (Actual ambient before shift)

40.0 (27.5)

40.0 (28.2)

--


During test, all opening blocked except rear side openings.




Temperature T of winding:

t1 (°C) R1 () t2 (°C) R2 () T (C) Allowed

Tmax (C)

Insulation class

-- -- -- -- -- -- -- --

-- -- -- -- -- -- -- --

-- -- -- -- -- -- -- --


The temperatures were measured by thermal couple (type K) method under worst case normal mode as described in 1.6.2 at voltage described in 1.4.5. The worst case normal mode is defined with max. load of the equipment.

With max. ambient temperature specified as 40 C, therefore, the maximum temperature rise is calculated as follows:

Components with:

- max. temp. of 105 C (PCB) 105 C

- max. temp. of 100 C (RTC) 100 C

- max. temp. of 100 C (PTC) 85 C

- when no class of insulation is given, min. insulation 105 C assumed.

User accessible area:

- material is plastic 95 C

- material is metal 70 C




4.6.1 &

4.6.2

TABLE: Enclosure openings P

Location Size (mm) Comments

Enclosure construction B, Horizontal, Vertical (with stand)

Top (near DC Fan)

Numerous of slot openings, each measured max. 4.9 mm by 0.9 mm.

No hazardous parts within 5 degrees of projection area.

Left Numerous of slot openings, each measured max. 4.9 mm by 0.9 mm.


Right No openings --

Bottom No openings --

Front side Metal part: Several hexagonal openings, each measured max. 6.68 mm in diagonal.

Decoration Part (covered on metal part):

Several slot openings, each measured max. 7.5 mm by 2.6

mm.


Rear side (Fan openings)

Several slot openings, each measured max. 4.5 mm by 6.75

mm.



See attached photos for the details coverage areas of openings.




5.1 TABLE: Touch current measurement N/A

Normal The tests are repeated in

reverse polarity

Test accessible part due to client request:

Power Adapter: FSP / FSP090-DIEBN2

Input voltage: 264 Vac

Input frequency: 60 Hz

Condition Current (mA) L, N output (+) Current (mA) L, N output (+) Comments

System ON 0.16 0.16 Switch “e” opened

Condition Current (mA) L, N plastic enclosure (with foil)

Current (mA) L, N plastic enclosure (with foil)

Comments

System ON 0.01 0.01 Switch “e” closed


Power Adapter: Delta / ADP-90MD H







Comments



Power Adapter: Chicony / A10-090P3A







Comments





5.3 TABLE: Fault condition tests P

Ambient temperature (C) ................................... : 25 C, if not specified.

Power source for EUT: Manufacturer, model/type, output rating ......................................................... :

See table 1.5.1 for details.

Component No. Fault Supply voltage (Vdc)

Test time Fuse # Fuse current

(A)

Observation




CPU fan Stalled 19 2 h -- -- Unit shutdown, no hazard, no damage. Maximum Temp:

Ambient= 26.9 C

PCB near CPU= 95.0 C

Ventilation openings

Blocked 19 2 h 49 min

-- -- Unit normal operating, no hazard, no damage. Maximum Temp:

Ambient= 26.6 C





CPU fan Stalled 19 2 h 9 min


Ambient= 28.3 C


Ventilation openings

Blocked 19 1 h 38 min


Ambient= 28.0 C



For RTC battery (RTC battery reverse current test)

RTC battery Normal 19 -- -- -- Measured normal reverse charging current = 0.02 mA

D20 (1-2) s-c 19 -- -- -- Measured abnormal reverse current = 3.18 mA

D20 (2-3) s-c 19 -- -- -- Measured abnormal reverse current = 2.94 mA

R33 s-c 19 -- -- -- Measured abnormal reverse current = 0.02 mA






(A)

Observation


OVERLOAD OF OPERATOR ACCESSIBLE CONNECTOR TEST (For US deviation)

VGA(J69), Pin9 to GND

o-l 19 1 h -- -- Open circuit voltage = 5.2 Vdc, Maximum available current = 1.9 A. No hazard.

VGA(J69), Pin1-8,10-17 to

GND

o-l 19 -- -- -- Open circuit voltage = 0 Vdc, Maximum available current = 0 A. No hazard.

HDMI(J124), Pin 18 to GND


HDMI(J124), Pin1-17,19 to

GND


DP(J125), Pin 20 to GND


DP(J125), Pin 1-19 to GND


SS USB1(J143),

Pin1,10 to GND


SS USB1(J143),

Pin2-9,11-18, to GND


SS USB1(J139),

Pin1,10 to GND


SS USB1(J139), Pin2-9,11-18


F SS USB1(J156),

Pin1,10 to GND


F SS USB1(J156),








(A)

Observation

F SS USB1(J151),

Pin1,10 to GND


F SS USB1(J151),



RJ45 (J8), Pin1-8 to GND



Fault: s-c = short circuit; o-l = overload

Note: The maximum abnormal charging current of RTC battery is 5 mA min.

Documents

IEC TEST REPORT FORM TEMPLATE - BitGravityasrock.pc.cdn.bitgravity.com/TSD/PEGA/JPT/DOC/CB/Jupiter... · Copy of marking plate The artwork below may be only a draft. ... Beitou District,