7/30/2019 icetme
1/2
International Conference on Innovations in Automation and
Mechatronics Engineering 2013 (ICIAME2013), 21-23 February 2013
G H Patel College of Engineering & Technology, Vallabh
Vidyanagar - 388120, State: Gujarat, INDIA
Instruction and Preparation of Full Papers for the Proceedings
of ICIAME2013
Bhavsar S.N.1*, Patel V.N.1, and Chauhan V.D.2
1Affiliation, Contact Address*Corresponding author, Email
2Affiliation, Contact Address
Email: [email protected]
Abstract The following instructions give the guidelines to
prepare a paper to be included in the proceedingsof the
International conference on Innovations in Automation and
Mechatronics Engineering 2013(ICIAME2013). Full Papers should be in
accordance with the style and format given in these
instructions.Abstract should not exceed 150 words.
Keywords Selected keywords relevant to the subject. Provide 3 to
5 keyword.
1. INTRODUCTION Manuscripts previously submitted or accepted
elsewhere for publication must not be submitted. Thepaper if
selected must be registered at least by any one of
the author(s) at the conference. To this effect, a
declaration form and registration form should besubmitted by the
authors together with the manuscript, if
the paper is selected for publication. The declaration formcan
be downloaded from the conference website.
Each paper must be divided into two parts. The firstpart
includes the title, authors name and affiliation,
abstract, and keywords. The second part is the main body
of the paper. Each paragraph has an indent of 6 afterprevious
paragraph.
2. PAPER SIZE AND FORMAT
Each paper size should be A4 (210 mm 297 mm) andthe following
margins should be set:
Left margin 20 mm
Right margin 20 mmTop margin 25 mm
Bottom margin 25 mmColumn width 82 mm
Column spacing 5.8 mm
3. FONTS AND STYLE3.1 First part
The first part includes the paper title, authors name,abstract,
and keywords. All the font types, font size and
font spacing of the title, authors name and affiliation,abstract
and keywords are as per given in this template.
3.2 Paper body
The second part consisting of the paper body must beedited in
the double column format, with each column 82
mm width and separated by 5.8 mm. The top-levelheading, usually
called section, numbered in Arabic
numerals, shall appear justified (left and right) on the
column with Times New Roman capital bold 11pt. The
numbered level-two heading starts from the left in TimesNew
Roman bold 10pt font. The main text uses Times
New Roman 10pt font with single spacing.
4. FIGURES, TABLES, AND EQUATIONS4.1 Figures and tables
All figures and tables should be placed after their firstmention
in the text. Large figures and tables may span
across both columns. Scanned images (e.g., line art,photos) can
be used if the output resolution is at least 300
dpi. Figure caption must be written as per given in
thetemplate.
Fig.1 The caption should be placed after the figure
Table1. The caption should be placed before the table
Sr. No. A B C
1 100 mm 60 % 900
2 50 mm 90 % 920
4.2 Equations
Equation numbers should be Arabic numerals enclosed
in parentheses on the right-hand margin. They should becited in
the text as, for example, Eq. (1), or Eqs. (1) ~ (3).
Equations start from the left on the column. Punctuate
mailto:[email protected]:[email protected]
7/30/2019 icetme
2/2
International Conference on Innovations in Automation and
Mechatronics Engineering 2013 (ICIAME2013), 21-23 February 2013
G H Patel College of Engineering & Technology, Vallabh
Vidyanagar - 388120, State: Gujarat, INDIA
equations with commas or periods when they are part of a
sentence.
For example,
y = mx + c (1)
Where, m is the slope.
4.3 References
References should appear in a separate reference
section (without numbering) at the end of the paper, asper the
format given in this template. Times New Roman
10pt is used for references. Acknowledgement sectionmay also be
included at the end of the paper before
reference section.
5. PAGE NUMBERS
Don't put a page number in the manuscript.
REFERENCES
[1] Bhavsar S.N., Aravindan S., and Rao P.V., An
accurate and efficient control over the present
numerical model of depth of sputtering in focused
ion beam milling, Journal of Nanoengineering and
Nanosystems N, 223, 9-18, 2009.
[2] Chauhan V.D., and Patel A.M., Water marking
using bit-plane slicing, International National
Conference on Innovations in Mechatronics
Engineering 2009, 23, 123-145, 2009.
[3] Bhavsar S.N., Aravindan S., and Rao P.V.,Machinability study
of cemented carbide using
focused ion beam (FIB) milling, Accepted for
Publication, Journal of Materials and Manufacturing
Processes.
[4] Refael C. Gonzalez, and Richard E. Woods,
Digital Image Processing, Addison-Wesley, 2nd
Edition, 2008.
