Hydraulic Accumulators SIL Certificate Exida

idae

Certification Services

IEC 61508 Functional Safety Assessment

Project: QHP Bladder Accumulator

Customer: Quality Hydraulic Power Ltd.

Middleton, Manchester United Kingdom

Contract No.: Q12/07-034 Report No.: QHP 12/07-034 R002

Version V1, Revision R1, August 20, 2013 Gregory Sauk

The document was prepared using best effort. The authors make no warranty of any kind and shall not be liable in any event for incidental or consequential damages in connection with the application of the document.

All rights reserved.

QHP 12-07-034 R002 V1R1 IEC 61508 Assessment.doc

Management Summary This report summarizes the results of the functional safety assessment according to IEC 61508 carried out on the:

QHP QB Series Bladder Accumulator

The functional safety assessment performed by exida consisted of the following activities:

- exida assessed the development process used by Quality Hydraulic Power Ltd. through an audit and creation of a detailed safety case against the requirements of IEC 61508.

- exida reviewed and assessed a detailed Failure Modes, Effects, and Diagnostic Analysis (FMEDA) of the devices to document the hardware architecture and failure behavior.

The functional safety assessment was performed to the requirements of IEC 61508, SIL 3. A full IEC 61508 Safety Case was prepared, using the exida SafetyCaseDB tool, and used as the primary audit tool. Hardware and software process requirements and all associated documentation were reviewed. Environmental test reports were reviewed. Also the user documentation (safety manual) was reviewed. The results of the Functional Safety Assessment can be summarized by the following statements:

The QHP 10 Litre Bladder Accumulator was found to meet the Systematic Capability requirements of IEC 61508 for up to SC 3 (SIL 3 Capable). The PFDAVG and architectural constraint requirements of the standard must be verified for each element of the safety function when using Route 1H. The manufacturer will be entitled to use the Functional Safety Logos.

exida T-023 V2R3 www.exida.com Page 2 of 17

QHP 12-07-034 R002 V1R1 IEC 61508 Assessment.doc exida T-023 V2R3 www.exida.com Page 3 of 17

Table of Contents Management Summary ................................................................................................... 2 1 Purpose and Scope ................................................................................................... 4 2 Project Management.................................................................................................. 5

2.1 exida...............................................................................................................................5 2.2 Roles of the parties involved...........................................................................................5 2.3 Standards and Literature used........................................................................................5 2.4 Reference documents.....................................................................................................5

2.4.1 Documentation provided by Quality Hydraulic Power Ltd. ...................................5 2.4.2 Documentation generated by exida.....................................................................7

3 Product Description ................................................................................................... 8 4 IEC 61508 Functional Safety Assessment............................................................... 10

4.1 Methodology .................................................................................................................10 4.2 Assessment Level.........................................................................................................10 4.3 Product Modifications....................................................................................................11

5 Results of the IEC 61508 Functional Safety Assessment........................................ 12 5.1 Lifecycle Activities and Fault Avoidance Measures ......................................................12

5.1.1 Functional Safety Management .........................................................................12 5.1.2 Safety Requirements Specification and Architecture Design.............................13 5.1.3 Hardware Design ...............................................................................................13 5.1.4 Validation ...........................................................................................................13 5.1.5 Verification .........................................................................................................13 5.1.6 Proven In Use ....................................................................................................14 5.1.7 Modifications ......................................................................................................14 5.1.8 User Documentation ..........................................................................................14

5.2 Hardware Assessment..................................................................................................15 6 Terms and Definitions.............................................................................................. 16 7 Status of the Document ........................................................................................... 17

7.1 Liability ..........................................................................................................................17 7.2 Releases .......................................................................................................................17 7.3 Future Enhancements...................................................................................................17 7.4 Release Signatures.......................................................................................................17


1 Purpose and Scope This document shall describe the results of the IEC 61508 functional safety assessment of the QHP Bladder Accumulator by exida according to the requirements of IEC 61508: ed2, 2010.

The results of this provides the safety instrumentation engineer with the required failure data as per IEC 61508 / IEC 61511 and confidence that sufficient attention has been given to systematic failures during the development process of the device.


2 Project Management

2.1 exida exida is one of the worlds leading accredited Certification Bodies and knowledge companies specializing in automation system safety and availability with over 300 years of cumulative experience in functional safety. Founded by several of the worlds top reliability and safety experts from assessment organizations and manufacturers, exida is a global company with offices around the world. exida offers training, coaching, project oriented system consulting services, safety lifecycle engineering tools, detailed product assurance, cyber-security and functional safety certification and a collection of on-line safety and reliability resources. exida maintains the largest process equipment database of failure rates and failure modes with over 60 billion unit operating hours.

exida is the market leader for IEC 61508 certification for currently active marketed products.

2.2 Roles of the parties involved Quality Hydraulic Power Ltd. Manufacturer of the QB Series Bladder Accumulator

exida Performed the hardware assessment

exida Performed the IEC 61508 Functional Safety Assessment

FMC Technologies contracted exida in September of 2012 with the IEC 61508 Functional Safety Assessment of the above mentioned device.

2.3 Standards and Literature used The services delivered by exida were performed based on the following standards / literature.

[N1] IEC 61508 (Parts 1 - 7): ed2, 2010

Functional Safety of Electrical/Electronic/Programmable Electronic Safety-Related Systems

2.4 Reference documents 2.4.1 Documentation provided by Quality Hydraulic Power Ltd. [D1] 170-9066, Rev 1, 2/27/09 QB010-A06-F17-341 Assy Dwg [D2] 030-1011, Rev 4, 11/8/12 Gas Valve Assembly Drawing [D3] BA 690Bar; V3-1; QHP Bladder Accumulators 690Bar Data Sheet [D4] IOM-QB; Iss 3; 2/1/09 IOM Manual - Bladder Accumulators [D5] IOM-QP; Iss 2; 3/1/08 IOM Manual - Piston Accumulators [D6] PCP567, Rev A, 7/30/13 QB Series Bladder Accumulator Safety Manual [D7] P Test Plan; Rev C; 7/23/12 Piston Accumulator Test Plan - Sample [D8] PCP 507; Rev A; 8/12/09 Assembly and Testing Procedure [D9] Test Certificate, 7/22/13 Test Results - Sample


[D10] QM; Iss 3; Rev 4; 8/29/12 Quality System Manual [D11] Cert ISO; 12/1/12 QHP ISO 9001:2008 Certificate [D12] QM 3.2; Iss 3; Rev 4; 8/1/12 Employee Job Description [D13] QM 8.2.2; Iss 3; Rev 5;

2/12/13 Internal Auditing Procedure

[D14] QP102; Iss 5; Rev 1; 8/1/12 Sub-Contractor QA Audit Procedure [D15] QP102 App A-Sample; Iss 5;

Rev 1 (Form); QHP Vendor Evaluation /Audit Questionnaire - Sample

[D16] QP102 App B-Sample; Iss 5; Rev 1 (Form);

QHP Vendor Rating Report - Sample

[D17] QP103; Iss 5; Rev 2; 8/1/12 Design Control, Development, Validation & Review Procedure

[D18] QP106 App J -Sample; Iss 5; Rev 1 (Form); 11/21/11

Accumulator Design Requirements and Review - Sample

[D19] QP106 App K; Iss 5; Rev 1 (Form); 8/1/12

QHP Contract Review Checklist

[D20] QP107; Iss 5; Rev 1; 8/1/12 Control and Calibration of Measuring and Inspection Equipment Procedure

[D21] QP108; Iss 5; Rev 2; 7/1/13 Document and Change Control Procedure [D22] QP108 App A-Sample; Iss 5;

Rev 1 (form); 12/5/12 Design Change Sample

[D23] QP110; Iss 5; Rev 2; 7/1/13 Non-Conformance, Corrective Action and Evaluation Procedure

[D24] QP111; Iss 5; Rev 2; 7/1/13 Purchasing Control Procedure [D25] QP113; Iss 5; Rev 2; 8/1/12 Procedure for Inspection & Testing [D26] QP116; Iss 5; Rev 1; 8/1/12 Procedure for Quality Control Monthly report [D27] QP118; Iss 5; Rev 0; 10/1/09 Procedure for Investigation and Analysis of Customer

Complaints [D28] QP119; Iss 5; Rev 1; 8/1/12 Learning, Training and Development Procedure [D29] Shipments Qty; n/a; 3/8/13 Shipment Totals Report [D30] Complaints; n/a; Complaint Analysis Summary [D31] Customer Data; n/a; Serial Number and Customer Information Records [D32] SIL Training; n/a; 12/16/12 Training Session Record - 61508 SIL Training [D33] Skills; n/a; Skills and Training Matrix [D34] Management Review,

1/22/13 Management Review Meeting - Sample Meeting Minutes

[D35] Training-Sample; 5/22/12 Training and Performance Review - Sample


2.4.2 Documentation generated by exida [R1] QHP Accumulator FMEDA

R2.xls, 6/18/2013 Failure Modes, Effects and Diagnostic Analysis,- QB Series Bladder Accumulator (internal document)

[R2] QHP Q12/07-034 R001 V1R2, 6/19/2013

FMEDA report - QB Series Bladder Accumulator

[R3] QHP Accumulators SafetyCaseDB IEC61508 R2.esc

QHP Bladder Accumulator IEC 61508 Compliance SafetyCaseDB (internal database)

[R4] PIU QHP Accumulators R2.xls, 6/19/2013

Proven In Use analysis (internal document)

[R5] QHP 12-07-034 R002 V1R1 IEC 61508 Assessment.doc, 8/20/2013

IEC 61508 Functional Safety Assessment for QHP Bladder Accumulator (This document)


3 Product Description The Quality Hydraulic Power Ltd. QB Series Bladder Accumulator are a series of elastomeric bladder based hydraulic accumulators used to store potential energy. These hydraulic accumulators store energy using a compressible and inert gas such as Nitrogen. The energy storage (compressed gas) is then utilized to exert force against a non-compressible fluid upon entry into the accumulator. The gas and fluid are separated by an elastomeric bladder.

Typically these can be used to store or receive hydraulic energy used in the activation of a final element subassembly for a Safety Instrumented Function (SIF).

The safety function for the Accumulator is to allow the final element subassembly to move to the safe position when the system is de-energized / energized depending upon the system configuration.

A second specialized application for a QB Series Bladder Accumulator was also included in this evaluation. For this specific application the Accumulator is used on a Low Pressure hydraulic return line and has check valves to isolate the bladder from other transient pressures on the main return line. The purpose is that when a device needs to quickly dump its pressure, that this will still happen quickly and at a low pressure even if there are other conditions which are causing a higher pressure in the return line. A typical application for this mode is shown in Figure 1 where item BA2 is the Bladder Accumulator.

Figure 1 Specialized Low Pressure Return Line application

Table 1 gives an overview of the different versions that were considered in the IEC 61508 assessment of the Series QB Accumulator.

exida

T-023 V2R3 www.exida.com Page 8 of 17


Table 1 Version overview

Device Description / Application

QB Accumulator QB Series Bladder Accumulator 10 Litre size

QB Accumulator QB Series Bladder Accumulator 10 Litre size, Low Pressure Return Line Application

The QB Series Bladder Accumulator is classified as a Type A1 device according to IEC 61508, having a hardware fault tolerance of 0.

1 Type A element: Non-Complex element (using discrete components); for details see 7.4.4.1.2 of IEC 61508-2, ed2, 2010.


4 IEC 61508 Functional Safety Assessment The IEC 61508 Functional Safety Assessment was performed based on the information received from Quality Hydraulic Power Ltd. and is documented in the SafetyCase [R3].

4.1 Methodology The full functional safety assessment includes an assessment of all fault avoidance and fault control measures during hardware and software development (if applicable) and demonstrates full compliance with IEC 61508 to the end-user. The assessment considers all requirements of IEC 61508. Any requirements that have been deemed not applicable have been marked as such in the full Safety Case report, e.g. software development requirements for a product with no software. The assessment also includes a review of existing manufacturing quality procedures to ensure compliance to the quality requirements of IEC 61508.

As part of the IEC 61508 functional safety assessment the following aspects have been reviewed:

Development process, including: o Functional Safety Management, including training and competence recording, FSM

planning, and configuration management

o Specification process, techniques and documentation o Design process, techniques and documentation, including tools used o Validation activities, including development test procedures, test plans and reports,

production test procedures and documentation

o Verification activities and documentation o Modification process and documentation o Installation, operation, and maintenance requirements, including user documentation o Manufacturing Quality System

Product design o Hardware architecture and failure behavior, documented in a FMEDA

The review of the development procedures is described in section 5.1. The review of the product design is described in section 5.2.

4.2 Assessment Level The QB Series Bladder Accumulator has been assessed per IEC 61508 to the following levels:

Systematic Capability SC 3 (SIL 3 capability) as the Proven In Use analysis justified that this device is suitable for use in applications with a maximum Safety Integrity Level of 3 (SIL 3) according to IEC 61508.

Architecture Constraint limitations of SIL 2 for a single device if the SFF for the complete final element is >60% when using Route 1H.


4.3 Product Modifications Quality Hydraulic Power Ltd. may make modifications to this product as needed. Modifications shall be classified into two types:

Type 1 Modification: Changes requiring re-certification, which includes the re-design of safety functions or safety integrity functions and all other changes that do not fit into the Type 2 category.

Type 2 Modification: Changes allowed to be made by Quality Hydraulic Power Ltd. without requiring re-certification provided that:

o A competent person from QHP has evaluated and documented that the change does not affect the Form, Fit or Function of the device. (For example: the wording or location of the nameplate)


5 Results of the IEC 61508 Functional Safety Assessment exida assessed the development process used by Quality Hydraulic Power Ltd. for this development against the objectives of IEC 61508 parts 1 and 2. This assessment was performed on-site and is documented in the SafetyCase [R3].

The current development process is fully compliant with IEC 61508. However, portions of the 10 Litre Bladder Accumulator were developed prior to the establishment of this IEC 61508 SIL 3 compliant development process. Consequently for the evaluation of systematic fault avoidance measures, proven in use claims were also considered in addition to the existing design documentation and additional documented safety analysis which showed the design integrity. The SafetyCase was created with project specific design documents.

5.1 Lifecycle Activities and Fault Avoidance Measures Quality Hydraulic Power Ltd. has a defined product lifecycle process in place. This is documented in QHPs Quality Management System which is ISO 9001 approved. No software is part of the design and therefore any requirements specific from IEC 61508 related to software and software development do not apply.

The assessment investigated the compliance with IEC 61508 of the processes, procedures and techniques as implemented for product design and development. The investigation was executed using subsets of the IEC 61508 requirements tailored to the SIL 3 work scope of the development team. The defined product lifecycle process was modified as a result of a previous audit which showed some areas for improvement. However, given the simple nature of the safety function and the extensive proven field experience for existing products QHP was able to demonstrate that the objectives of the standard have been met. The result of the assessment can be summarized by the following observations: The audited Quality Hydraulic Power Ltd. design and development process complies with the relevant managerial requirements of IEC 61508 SIL 3.

5.1.1 Functional Safety Management FSM Planning Quality Hydraulic Power Ltd. has a defined process in place for product design and development. Required activities are specified along with review and approval requirements. This is primarily documented in QP103 [D17]. Templates, forms and sample documents are provided. The same process is used for modifications. This process and procedures referenced herein fulfill the requirements of IEC 61508 with respect to functional safety management for a product with simple complexity and well defined safety functionality.

Version Control Quality Hydraulic Power Ltd. Procedure QP108 [D21] requires that all documents be version controlled. Document revisions were evident during the audit.


Training, Competency recording QP119 requires the Human Resource department to maintain training records of education, experience, training and qualifications for all personnel. Department heads are responsible for identifying and providing the training needs for their department as well as proficiency evaluations. The procedures and records were examined and found up-to-date and sufficient. Quality Hydraulic Power Ltd. hired exida to be the independent assessor per IEC 61508 and to provide specific IEC 61508 knowledge.

5.1.2 Safety Requirements Specification and Architecture Design For the Series QB Accumulator, the simple safety functionality is the primary functionality of the product (supply / store hydraulic energy). Therefore no special Safety Requirements Specification was needed. The normal functional requirements were sufficient. As the Accumulators are relatively simple and are based upon standard designs with extensive field history, no semi-formal methods are needed. General design and testing methodology is documented and required as part of the design process. This meets SIL 3.

5.1.3 Hardware Design The design process is documented in QP103 [D17]. Items from IEC 61508-2, Table B.2 include observance of guidelines and standards (PED, API NACE, ATEX), project management, documentation (design outputs are documented per quality procedures), structured design, modularization, use of well-tried components, and computer-aided design tools. This meets SIL 3.

5.1.4 Validation Validation Testing is done via a documented plan created that links to the products requirements specifications and also includes compliance testing per application and agency standards. QHP also maintains a set of standard tests that are used to validate their designs and production units. As the QHP Bladder Accumulator is a purely mechanical device with a simple safety function, there is no separate integration testing necessary. The 10 Litre Bladder Accumulator performs only one Safety Function, which is extensively tested under various conditions during validation testing.

Items from IEC 61508-2, Table B.3 include functional testing, project management, documentation, and black-box testing (for the considered devices this is similar to functional testing). Field experience and statistical testing via regression testing are not applicable. This meets SIL 3.

Items from IEC 61508-2, Table B.5 included functional testing and functional testing under environmental conditions, project management, documentation, failure analysis (analysis on products that failed), expanded functional testing, black-box testing, and fault insertion testing. This meets SIL 3.

5.1.5 Verification The development and verification activities are also defined in QP103 [D17]. For each design phase the objectives are stated, the required input and output documents are specified and necessary review activities are determined. Verification activities also included a design FMEA and review, a third party FMEDA, and other reviews of the tests and test results. The results of these activities were documented and reviewed. This meets SIL 3.


5.1.6 Proven In Use In addition to the Design Fault avoidance techniques listed above, a Proven in Use evaluation was carried out on the QB Series Bladder Accumulator during the certification activity. Shipment records from 2008 to 2012 were used to determine that the Series QB Accumulators have >300 million operating hours and that they have demonstrated a field failure rate in line with the failure rates indicated in the FMEDA reports. This meets the requirements for Proven In Use for SIL 3.

5.1.7 Modifications Modifications are initiated per QP108 Change Control procedure. All changes are first reviewed and analyzed for impact before being approved. This certification only allows QHP to make Type 2 changes that have no effect on the Form, Fit or Function of the Accumulator without having to be re-certified.

5.1.8 User Documentation Quality Hydraulic Power Ltd. has created a Safety Manual for the 10 Litre Bladder Accumulator, see [D6]. This safety manual was assessed by exida. It contained all required information given the simplicity of the products. The FMEDA reports are available and they contain failure rate, failure mode, useful life and suggested proof test information. The combination of the Safety Manual and the FMEDAs are considered to be in compliance with the requirements of IEC 61508.

Requirements from IEC 61508-2, Table B.4 that have been met by Quality Hydraulic Power Ltd. include operation and maintenance instructions, user friendliness, maintenance friendliness, project management, documentation, limited operation possibilities (the products perform well-defined actions) and operation only by skilled operators (operators familiar with this type of equipment, although this is partly the responsibility of the end-user). This meets the requirements for SIL 3.


5.2 Hardware Assessment To evaluate the hardware design of the 10 Litre Bladder Accumulator, a Failure Modes, Effects, and Diagnostic Analysis was performed by exida for each component in the system. This is documented in [R1] and [R2].

A Failure Modes and Effects Analysis (FMEA) is a systematic way to identify and evaluate the effects of different component failure modes, to determine what could eliminate or reduce the chance of failure, and to document the system in consideration. An FMEDA (Failure Mode Effect and Diagnostic Analysis) is an FMEA extension. It combines standard FMEA techniques with extension to identify online diagnostics techniques and the failure modes relevant to safety instrumented system design.

From the FMEDA failure rates are derived for each important failure category. All failure rate analysis results and useful life limitations are listed in the FMEDA report [R2].

Note, as the Series QB Accumulator is only one component of a final element, the SFF must be calculated for the entire final element combination if following the Route 1H hardware architectural constraints. It is the end users responsibility to confirm this for each particular application and to include all components of the final element in the calculations.

The analysis shows that the design of the Series QB Accumulator can meet the hardware requirements of IEC 61508, SIL 3 and SIL 2 depending on the complete final element design. The Hardware Fault Tolerance, PFDAVG, and Safe Failure Fraction (when not following Route 2H) requirements of the IEC 61508 must be verified for each specific design.


6 Terms and Definitions Automatic Diagnostics Tests performed on line internally by the device or, if specified, externally

by another device without manual intervention.

exida criteria A conservative approach to arriving at failure rates suitable for use in hardware evaluations utilizing the 2H Route in IEC 61508-2.

Fault tolerance Ability of a functional unit to continue to perform a required function in the presence of faults or errors (IEC 61508-4, 3.6.3)

FIT Failure In Time (1x10-9 failures per hour)

FMEDA Failure Mode Effect and Diagnostic Analysis

HFT Hardware Fault Tolerance

Low demand mode Mode, where the demand interval for operation made on a safety-related system is greater than twice the proof test interval.

PFDAVG Average Probability of Failure on Demand

PVST Partial Valve Stroke Test

It is assumed that the Partial Stroke Testing, when performed, is automatically performed at least an order of magnitude more frequent than the proof test, therefore the test can be assumed an automatic diagnostic. Because of the automatic diagnostic assumption the Partial Valve Stroke Testing also has an impact on the Safe Failure Fraction.

Random Capability The SIL limit imposed by the Architectural Constraints for each element.

SFF Safe Failure Fraction summarizes the fraction of failures, which lead to a safe state and the fraction of failures which will be detected by diagnostic measures and lead to a defined safety action.

SIF Safety Instrumented Function

SIL Safety Integrity Level

SIS Safety Instrumented System Implementation of one or more Safety Instrumented Functions. A SIS is composed of any combination of sensor(s), logic solver(s), and final element(s).

Type A element Non-Complex element (using discrete components); for details see 7.4.4.1.2 of IEC 61508-2


7 Status of the Document

7.1 Liability exida prepares reports based on methods advocated in International standards. exida accepts no liability whatsoever for the use of this report or for the correctness of the standards on which the general calculation methods are based.

7.2 Releases Version: V1 Revision: R1 Version History: V1, R1: Released; August 20, 2013 V0, R1: Draft; August 15, 2013 Authors: Gregory Sauk Review: Steven Close; August 20, 2013 Release status: Released

7.3 Future Enhancements At request of client.

7.4 Release Signatures

Gregory Sauk, CFSE, Senior Safety Engineer

Steven Close, Senior Safety Engineer

exida T-023 V2R3 www.exida.com Page 17 of 17

Management SummaryTable of Contents1 Purpose and Scope2 Project Management2.1 exida2.2 Roles of the parties involved2.3 Standards and Literature used2.4 Reference documents2.4.1 Documentation provided by Quality Hydraulic Power Ltd.2.4.2 Documentation generated by exida

3 Product Description4 IEC 61508 Functional Safety Assessment4.1 Methodology4.2 Assessment Level4.3 Product Modifications

5 Results of the IEC 61508 Functional Safety Assessment5.1 Lifecycle Activities and Fault Avoidance Measures5.1.1 Functional Safety Management5.1.2 Safety Requirements Specification and Architecture Design5.1.3 Hardware Design5.1.4 Validation5.1.5 Verification5.1.6 Proven In Use5.1.7 Modifications5.1.8 User Documentation

5.2 Hardware Assessment

6 Terms and Definitions7 Status of the Document7.1 Liability7.2 Releases7.3 Future Enhancements7.4 Release Signatures

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice

Documents

Hydraulic Accumulators SIL Certificate Exida