HUAWEI S9700 Switch Hardware Description

S9700 Core Routing Switch

Hardware Description

Issue 04Date 2013-05-30

HUAWEI TECHNOLOGIES CO., LTD.

Copyright Huawei Technologies Co., Ltd. 2013. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and thecustomer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,and recommendations in this document are provided "AS IS" without warranties, guarantees or representationsof any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Technologies Co., Ltd.Address: Huawei Industrial Base

Bantian, LonggangShenzhen 518129People's Republic of China

Website: http://enterprise.huawei.com

Issue 04 (2013-05-30) Huawei Proprietary and ConfidentialCopyright Huawei Technologies Co., Ltd.

i

About This Document

Intended AudienceThis document describes hardware features of the S9700 and helps readers get familiar witheach chassis model, card, and cable.This document is intended for:l Network planning engineersl Hardware installation engineersl Commissioning engineersl On-site maintenance engineersl System maintenance engineers

Symbol ConventionsThe symbols that may be found in this document are defined as follows.

Symbol Description

DANGERIndicates a hazard with a high level or medium level of riskwhich, if not avoided, could result in death or serious injury.

WARNINGIndicates a hazard with a low level of risk which, if notavoided, could result in minor or moderate injury.

CAUTIONIndicates a potentially hazardous situation that, if notavoided, could result in equipment damage, data loss,performance deterioration, or unanticipated results.

TIP Provides a tip that may help you solve a problem or save time.

NOTE Provides additional information to emphasize or supplementimportant points in the main text.

S9700 Core Routing SwitchHardware Description About This Document


ii

Command ConventionsThe command conventions that may be found in this document are defined as follows.

Convention DescriptionBoldface The keywords of a command line are in boldface.Italic Command arguments are in italics.[ ] Items (keywords or arguments) in brackets [ ] are optional.{ x | y | ... } Optional items are grouped in braces and separated by

vertical bars. One item is selected.[ x | y | ... ] Optional items are grouped in brackets and separated by

vertical bars. One item is selected or no item is selected.{ x | y | ... }* Optional items are grouped in braces and separated by

vertical bars. A minimum of one item or a maximum of allitems can be selected.

[ x | y | ... ]* Optional items are grouped in brackets and separated byvertical bars. You can select one or several items, or selectno item.

& The parameter before the & sign can be repeated 1 to n times.# A line starting with the # sign is comments.

Change HistoryUpdates between document issues are cumulative. Therefore, the latest document issue containsall updates made in previous issues.

Issue 04 (2013-05-30)This version has the following updates:The documentation is modified according to updates in V200R003C00.

Issue 03 (2013-04-20)This version has the following updates:l 7.2 AC Power Cable

Issue 02 (2013-02-08)This version has the following updates:l 2 Cabinet



iii

Issue 01 (2012-12-08)Initial commercial release.



iv

Contents

About This Document.....................................................................................................................ii1 Version Support for Components..............................................................................................11.1 Components Available in V200R001C00......................................................................................................................21.2 Components Available in V200R002C00......................................................................................................................51.3 Components Available in V200R003C00......................................................................................................................92 Cabinet...........................................................................................................................................142.1 N66E Cabinet...............................................................................................................................................................152.1.1 Appearance of an N66E Cabinet...............................................................................................................................152.1.2 N66E Cabinet Physical Specifications......................................................................................................................152.1.3 Components of an N66E Cabinet..............................................................................................................................192.1.4 Structural Features of an N66E Cabinet....................................................................................................................192.2 N68E Cabinet...............................................................................................................................................................232.2.1 Appearance of an N68E Cabinet...............................................................................................................................232.2.2 N68E Cabinet Physical Specifications......................................................................................................................232.2.3 Components of an N68E cabinet...............................................................................................................................272.2.4 Structural Features of an N68E Cabinet....................................................................................................................273 Chassis...........................................................................................................................................323.1 Chassis Models.............................................................................................................................................................333.2 S9703............................................................................................................................................................................333.2.1 Version Mapping.......................................................................................................................................................333.2.2 Appearance and Structure..........................................................................................................................................343.2.3 Slots...........................................................................................................................................................................363.2.4 Power Supply Principles............................................................................................................................................383.2.5 Heat Dissipation........................................................................................................................................................403.2.6 Specifications.............................................................................................................................................................413.3 S9706............................................................................................................................................................................443.3.1 Version Mapping.......................................................................................................................................................443.3.2 Appearance and Structure..........................................................................................................................................443.3.3 Slots...........................................................................................................................................................................473.3.4 Power Supply Principles............................................................................................................................................503.3.5 Heat Dissipation........................................................................................................................................................523.3.6 Specifications.............................................................................................................................................................54

S9700 Core Routing SwitchHardware Description Contents


v

3.4 S9712............................................................................................................................................................................573.4.1 Version Mapping.......................................................................................................................................................573.4.2 Appearance and Structure..........................................................................................................................................573.4.3 Slots...........................................................................................................................................................................613.4.4 Power Supply Principles............................................................................................................................................653.4.5 Heat Dissipation........................................................................................................................................................663.4.6 Specifications.............................................................................................................................................................694 Power Modules............................................................................................................................734.1 2200 W DC Power Module..........................................................................................................................................744.2 800 W AC Power Module............................................................................................................................................774.3 2200 W AC Power Module..........................................................................................................................................815 Fan Module...................................................................................................................................865.1 S9700 Fan Module........................................................................................................................................................876 Cards..............................................................................................................................................916.1 Introduction..................................................................................................................................................................926.1.1 Naming Conventions.................................................................................................................................................926.1.2 Card Classifications...................................................................................................................................................986.1.3 Card Structure and Dimensions...............................................................................................................................1086.1.4 Port Numbering.......................................................................................................................................................1106.2 Main Control Units and Subcards..............................................................................................................................1116.2.1 EH1D2SRUC000-S9706/S9712 Main Control Unit C (Optional Clock)...............................................................1116.2.2 EH1D2SRUDC00/EH1D2SRUDC01-Main Control Unit D-Clock.......................................................................1186.2.3 EH1D2MCUAC00-Main Control Unit-Clock........................................................................................................1266.2.4 LE0D00CKMA00-Clock Pinch Board,...................................................................................................................1336.2.5 EH1D2VS08000-8-Port 10G Cluster Switching System Service Unit (SFP+)......................................................1386.3 EH1D200CMU00-Centralized Monitoring Unit........................................................................................................1436.3.1 Introduction.............................................................................................................................................................1436.3.2 Version Mapping.....................................................................................................................................................1446.3.3 Functions and Features............................................................................................................................................1446.3.4 Indicators and Ports.................................................................................................................................................1456.3.5 Specifications...........................................................................................................................................................1466.3.6 Ordering Information...............................................................................................................................................1476.4 LE0D0VAMPA00-Value-Added Service Unit..........................................................................................................1486.4.1 Introduction.............................................................................................................................................................1486.4.2 Version Mapping.....................................................................................................................................................1486.4.3 Functions and Features............................................................................................................................................1496.4.4 Indicators and Ports.................................................................................................................................................1496.4.5 Specifications...........................................................................................................................................................1516.4.6 Ordering Information...............................................................................................................................................1526.5 EH1D2PS00P00 -Open Service Platform Unit..........................................................................................................1536.5.1 Introduction.............................................................................................................................................................153



vi

6.5.2 Version Mapping.....................................................................................................................................................1536.5.3 Functions and Features............................................................................................................................................1536.5.4 Indicators and Ports.................................................................................................................................................1556.5.5 Specifications...........................................................................................................................................................1586.5.6 Ordering Information...............................................................................................................................................1596.6 100M Interface Card...................................................................................................................................................1606.6.1 EH1D2F48T-48-Port 10/100BASE-T Interface Card (RJ45).................................................................................1606.6.2 EH1D2F48S-48-Port 100BASE-X Interface Card (SFP).......................................................................................1666.7 1000M Interface Card.................................................................................................................................................1726.7.1 EH1D2G24S 24-Port 100/1000BASE-X Interface Card (SFP)..............................................................................1726.7.2 EH1D2S24CSA0-24-Port 100/1000BASE-X and 8-Port 10/100/1000BASE-T Combo Interface Card (SA, SFP/RJ45).................................................................................................................................................................................1796.7.3 EH1D2S24CEA0-24-Port 100/1000BASE-X and 8-Port 10/100/1000BASE-T Combo Interface Card(EA, SFP/RJ45, 1588).......................................................................................................................................................................1856.7.4 EH1D2T36SEA0-36-Port 10/100/1000BASE-T and 12-Port 100/1000BASE-X Interface Card (EA, RJ45/SFP)..........................................................................................................................................................................................1916.7.5 EH1D2G24TFA0-24-Port 10/100/1000BASE-T Interface Card (FA, RJ45).........................................................1966.7.6 EH1D2G48T-48-Port 10/100/1000BASE-T Interface Card (RJ45).......................................................................2016.7.7 EH1D2G48TBC0-48-Port 10/100/1000BASE-T Interface Card (BC, RJ45).........................................................2086.7.8 EH1D2G48S-48-Port 100/1000BASE-X Interface Card (SFP)..............................................................................2146.7.9 EH1D2G48SBC0-48-Port 100/1000BASE-X Interface Card (BC, SFP)...............................................................2226.8 GE/10GE Interface Card............................................................................................................................................2296.8.1 EH1D2T24XEA0-24-Port 10/100/1000BASE-T and 2-Port 10GBASE-X Interface Card (EA, RJ45/XFP)........2296.8.2 EH1D2S24X-24-Port 100/1000BASE-X and 2-Port 10GBASE-X Interface Card (SFP/XFP).............................2346.9 10GE Interface Card...................................................................................................................................................2416.9.1 EH1D2X02X-2-Port 10GBASE-X Interface Card (XFP).......................................................................................2416.9.2 EH1D2X04X-4-Port 10GBASE-X Interface Card (XFP).......................................................................................2476.9.3 EH1D2X08SED4/EH1D2X08SED5-8-Port 10GBASE-X Interface Card (ED, SFP+).........................................2546.9.4 EH1D2X12SSA0-12-Port 10GBASE-X Interface Card (SA, SFP+).....................................................................2606.9.5 EH1D2X16SFC0 16-Port 10GBASE-X Interface Card (FC, SFP+)......................................................................2656.9.6 EH1D2X40SFC0 40-Port 10GBASE-X Interface Card (FC, SFP+)......................................................................2716.10 40GE Interface Card.................................................................................................................................................2776.10.1 EH1D2L02QFC0-2-Port 40GBASE-X Interface Card (FC, QSFP+)...................................................................2776.10.2 EH1D2L08QFC0-8-Port 40GBASE-X Interface Card (FC, QSFP+)...................................................................2846.11 POS Interface Card...................................................................................................................................................2906.11.1 EH1D2WM00000 - WAN Interface Service Process Card...................................................................................2906.11.2 P1UF-1-Port OC-48c/STM-16c POS-SFP Flexible Card.....................................................................................2956.11.3 P4HF-4-Port OC-12c/STM-4c POS-SFP Flexible Card.......................................................................................3006.11.4 P4CF-4-Port OC-3c/STM-1c POS-SFP Flexible Card.........................................................................................3057 Cables...........................................................................................................................................3107.1 DC Power Cable.........................................................................................................................................................3117.2 AC Power Cable.........................................................................................................................................................3127.3 Ground Cable for the Chassis and Cabinet.................................................................................................................313



vii

7.4 Console Cable.............................................................................................................................................................3137.5 Ethernet Cable............................................................................................................................................................3147.6 Clock Cable................................................................................................................................................................3167.7 High-Speed Cable.......................................................................................................................................................3187.8 Optical Fiber...............................................................................................................................................................3218 Pluggable Modules for Interfaces..........................................................................................3298.1 Concepts.....................................................................................................................................................................3308.2 SFP/eSFP Modules.....................................................................................................................................................3338.3 SFP+ Modules............................................................................................................................................................3418.4 XFP Modules..............................................................................................................................................................3458.5 QSFP+ Modules.........................................................................................................................................................3498.6 Huawei Certification...................................................................................................................................................351



viii

1 Version Support for ComponentsAbout This Chapter

1.1 Components Available in V200R001C001.2 Components Available in V200R002C001.3 Components Available in V200R003C00

S9700 Core Routing SwitchHardware Description 1 Version Support for Components


1

1.1 Components Available in V200R001C00NOTE

Components marked with * are added in V200R001C00.

Table 1-1 shows components available in the S9700 V200R001C00.

Table 1-1 Components available in S9700 V200R001C00Component Name DescriptionChassis S9703 chassis -

S9706 chassis -S9712 chassis -S9703 FCC chassis The chassis have gained an

FCC certificate.S9706 FCC chassisS9712 FCC chassis

Power module 2200 W DC power module -2200 W AC power module -

Fan module S9700 fan module -MPU EH1D2SRUDC00 S9706/S9712 Main Control

Unit D, ClockEH1D2SRUDC01 S9706/S9712 Main Control

Unit D, Clock, FCCEH1D2MCUAC00 S9703 Main Control Unit A,

clockSubcard on the MPU LE0D00CKMA00 Clock Pinch BoardCMU EH1D200CMU00 Centralized Monitoring UnitValue-added service card LE0D0WMNPA00 Value-added service card100M interface card EH1D2F48TEA0 48-port 10/100BASE-T

interface card (EA,RJ45)-32K MAC

EH1D2F48TEC0 48-port 10/100BASE-Tinterface card (EC,RJ45)-128K MAC

EH1D2F48TFA0 48-port 10/100BASE-Tinterface card (FA,RJ45)-32K MAC



2

Component Name DescriptionEH1D2F48SEA0 48-port 100BASE-X

interface card (EA,SFP)-32K MAC

EH1D2F48SEC0 48-port 100BASE-Xinterface card (EC,SFP)-128K MAC

GE interface card EH1D2G24SSA0 24-port 100/1000BASE-Xinterface card (SA,SFP)-32K MAC

EH1D2G24SEC0 24-port 100/1000BASE-Xinterface card (EC,SFP)-128K MAC

EH1D2G24SED0 24-port 100/1000BASE-Xinterface card (ED,SFP)-512K MAC

EH1D2S24CSA0 24-port 100/1000BASE-Xand 8-port10/100/1000BASE-T combointerface card (SA, SFP/RJ45)-32K MAC

EH1D2S24CEA0 24-port 100/1000BASE-Xand 8-port10/100/1000BASE-T combointerface card (EA, SFP/RJ45)-32K MAC

EH1D2G24TFA0 24-port 10/100/1000BASE-T interface card (FA,RJ45)-32K MAC

EH1D2T36SEA0 36-port 10/100/1000BASE-T and 12-port100/1000BASE-X interfacecard (EA, RJ45/SFP)-32KMAC

EH1D2G48TEA0 48-port 10/100/1000BASE-T interface card (EA,RJ45)-32K MAC

EH1D2G48TEC0 48-port 10/100/1000BASE-T interface card (EC,RJ45)-128K MAC

EH1D2G48TED0 48-port 10/100/1000BASE-T interface card (ED,RJ45)-512K MAC



3

Component Name DescriptionEH1D2G48TFA0 48-port 10/100/1000BASE-

T interface card (FA,RJ45)-32K MAC

EH1D2G48TBC0 48-port 10/100/1000BASE-T interface card (BC,RJ45)-128K MAC

EH1D2G48SEA0 48-port 100/1000BASE-Xinterface card (EA,SFP)-32K MAC



EH1D2G48SFA0 48-port 100/1000BASE-Xinterface card (FA,SFP)-32K MAC

EH1D2G48SBC0 48-port 100/1000BASE-Xinterface card (BC,SFP)-128K MAC

GE/10GE interface card EH1D2T24XEA0 24-port 10/100/1000BASE-T and 2-port 10GBASE-Xinterface card (EA, RJ45/XFP)-32K MAC

EH1D2S24XEA0 24-port 100/1000BASE-Xand 2-port 10GBASE-Xinterface card (EA, SFP/XFP)-32K MAC

EH1D2S24XEC0 24-port 100/1000BASE-Xand 2-port 10GBASE-Xinterface card (EC, SFP/XFP)-128K MAC

10GE interface card EH1D2X02XEA0 2-port 10GBASE-X interfacecard (EA, XFP)-32K MAC

EH1D2X02XEC0 2-port 10GBASE-X interfacecard (EC, XFP)-128K MAC

EH1D2X04XEA0 4-port 10GBASE-X interfacecard (EA, XFP)-32K MAC




4

Component Name DescriptionEH1D2X04XED0 4-port 10GBASE-X interface

card (ED, XFP)-512K MACEH1D2X12SSA0 12-port 10GBASE-X

interface card (SA, SFP+)-32K MAC

EH1D2X16SFC0 16-port 10GBASE-Xinterface card (FC, SFP+)-128K MAC


POS interface card EH1D2WM00000 WAN interface serviceprocessing card

P4CF 4-port OC-3c/STM-1c POS-SFP flexible card (installedon the WAN interface serviceprocessing card)

P4HF 4-port OC-12c/STM-4cPOS-SFP flexible card(installed on the WANinterface service processingcard)

P1UF 1-port OC-48c/STM-16cPOS-SFP flexible card(installed on the WANinterface service processingcard)





S9706 chassis -



5

Component Name DescriptionS9712 chassis -S9703 FCC chassis The chassis have gained an


Power module 2200 W DC power module -2200 W AC power module -800 W AC power module* -




clockSubcard on the MPU LE0D00CKMA00 Clock Pinch BoardCMU EH1D200CMU00 Centralized Monitoring UnitValue-added service card LE0D0WMNPA00 Value-added service cardOSPU EH1D2PS00P00* Open Service Platform Unit100M interface card EH1D2F48TEA0 48-port 10/100BASE-T




EH1D2F48SEA0 48-port 100BASE-Xinterface card (EA,SFP)-32K MAC

EH1D2F48SEC0 48-port 100BASE-Xinterface card (EC,SFP)-128K MAC




6

Component Name DescriptionEH1D2G24SEC0 24-port 100/1000BASE-X

interface card (EC,SFP)-128K MAC










EH1D2G48TBC0 48-port 10/100/1000BASE-T interface card (BC,RJ45)-128K MAC




7

Component Name DescriptionEH1D2G48SEC0 48-port 100/1000BASE-X












EH1D2X04XED0 4-port 10GBASE-X interfacecard (ED, XFP)-512K MAC

EH1D2X12SSA0 12-port 10GBASE-Xinterface card (SA, SFP+)-32K MAC




8

Component Name DescriptionEH1D2X40SFC0 40-port 10GBASE-X

interface card (FC, SFP+)-128K MAC

EH1D2X08SED4* 8-port 10GBASE-X interfacecard (ED, SFP+)-512K MAC

EH1D2X08SED5* 8-port 10GBASE-X interfacecard (ED, SFP+)-512K MAC

40GE interface card EH1D2L02QFC0* 2-port 40GBASE-X interfacecard (FC, QSFP+)-128KMAC

EH1D2L08QFC0* 8-port 40GBASE-X interfacecard (FC, QSFP+)-128KMAC











9

Component Name DescriptionS9706 chassis -S9712 chassis -S9703 FCC chassis The chassis have gained an


Power module 2200 W DC power module -2200 W AC power module -800 W AC power module -




clockEH1D2SRUC000* S9706/S9712 Main Control

Unit C (Optional Clock)Subcard on the MPU LE0D00CKMA00 Clock Pinch Board

EH1D2VS08000* 8-Port 10G ClusterSwitching System ServiceUnit (SFP+)

CMU EH1D200CMU00 Centralized Monitoring UnitValue-added service card LE0D0WMNPA00 Value-added service cardOSPU EH1D2PS00P00 Open Service Platform Unit100M interface card EH1D2F48TEA0 48-port 10/100BASE-T




EH1D2F48SEA0 48-port 100BASE-Xinterface card (EA,SFP)-32K MAC



10

Component Name DescriptionEH1D2F48SEC0 48-port 100BASE-X















11

Component Name DescriptionEH1D2G48TBC0 48-port 10/100/1000BASE-

T interface card (BC,RJ45)-128K MAC













EH1D2X04XED0 4-port 10GBASE-X interfacecard (ED, XFP)-512K MAC



12

Component Name DescriptionEH1D2X12SSA0 12-port 10GBASE-X

interface card (SA, SFP+)-32K MAC



EH1D2X08SED4 8-port 10GBASE-X interfacecard (ED, SFP+)-512K MAC

EH1D2X08SED5 8-port 10GBASE-X interfacecard (ED, SFP+)-512K MAC

EH1D2X02XEC1* 2-port 10GBASE-X interfacecard (EC, XFP), FCC

EH1D2X04XEC1* 4-port 10GBASE-X interfacecard (EC, XFP), FCC

40GE interface card EH1D2L02QFC0 2-port 40GBASE-X interfacecard (FC, QSFP+)-128KMAC

EH1D2L08QFC0 8-port 40GBASE-X interfacecard (FC, QSFP+)-128KMAC







13

2 CabinetAbout This Chapter

2.1 N66E CabinetThis section describes the appearance, technical specifications, components, operatingenvironment, and structural features of an N66E cabinet.2.2 N68E CabinetThis section describes the appearance, technical specifications, components, and structuralfeatures of an N68E cabinet.

S9700 Core Routing SwitchHardware Description 2 Cabinet


14

2.1 N66E CabinetThis section describes the appearance, technical specifications, components, operatingenvironment, and structural features of an N66E cabinet.

2.1.1 Appearance of an N66E CabinetFigure 2-1 shows an N66E cabinet.

Figure 2-1 N66E cabinet

2.1.2 N66E Cabinet Physical SpecificationsTable 2-1 lists physical specifications of an N66E cabinet.



15

Table 2-1 N66E cabinet physical specificationsItem SpecificationEmpty cabinet weightNOTE

Empty cabinet weight is the weight of a cabinetwith a front door, a rear door, and two side panels.

73 kg1 kg

Dimensions (W x D x H) 600 mm x 600 mm x 2200 mm24 in. x 24 in. x 87 in.

Mounting holes on the top l Position (W x H): 450 mm x 400 mml Nuts: six M8 self-clinching nuts

Mounting holes on the bottom l Position (W x H): 413 mm x 487 mml Hole diameter: 18l Nuts: four M12 expansion bolts and

matching nutsDistance between holes on mounting rails When marking the installation positions of a

chassis on mounting rails, count every fourholes with a wide-wide-narrow intervalarrangement as 1 U.Any four adjacent holes on a mounting railmake a distance of 1 U. There are threeinterval arrangements for four adjacent holeson a mounting rail, as shown in Figure 2-2.

Figure 2-2 Interval arrangements for fouradjacent holes

1U

1U

1U

W-W-N W-N-W N-W-W

W: WideN: Narrow

NOTEThe interval between two holes is the distancebetween the axes of the holes.1 U equals 1.75 in. (44.45 mm). U is a unit of heightdefined in International ElectrotechnicalCommission (IEC) 60297.



16

Item SpecificationAvailable space 46 UAngle opening width 450 mmSpace for a chassis (distance between axes ofmounting holes)

465 mm

Distance between a front mounting rail andinterior of the front door

95 mm

Figure 2-3 shows the dimensions of an N66E cabinet.



17

Figure 2-3 N66E cabinet dimensions



18

2.1.3 Components of an N66E CabinetFigure 2-4 show the components of a rear-serviceable cabinet.

Figure 2-4 Components of a rear-serviceable N66E cabinet

1

2

3

4

(1) Front door (2) Rack (3) Rear door (4) Side panels

2.1.4 Structural Features of an N66E CabinetCabinet Material

The surface of the cabinet and the rack is purplish grey.An N66E cabinet is made of welded electro-galvanized steel sheets and cold-rolled steel sheets.The fireproof performance of the internal materials complies with the Underwriter Laboratories(UL) standards.



19

Cabling ModeCable apertures are reserved on the top and at the bottom of the N66E cabinet, so that the N66Ecabinet supports overhead cabling and underfloor cabling:l In the overhead cabling mode, external cables enter the cabinet through the top of the

cabinet. Figure 2-5 shows the cable apertures.l In the underfloor cabling mode, external cables enter the cabinet through the bottom of the

cabinet.NOTEThe devices described in this document use the overhead cabling mode.

Figure 2-5 Cable apertures on the cabinet top

500mm

52mm 52mm

500mm

175mm22mm

Networkcable/fiber

Networkcable/fiber

Power cable

Reserved holes

Power cable hole

Front Door

Heat DissipationThe front door, rear door, and top plate of an N66E cabinet have high-density air vents. Therefore,the cabinet supports front air intake, rear air exhaust, and upper air exhaust, and provides goodheat dissipation performance.

NOTE

l The devices described in this document adopt left-to-back airflow for heat dissipation.l The airflow of devices described in this document in the cabinet is: front of the cabinet -> left side of

the equipment -> inside the equipment -> rear of the equipment -> rear of the cabinet, as shown inFigure 2-6.



20

Figure 2-6 Airflow in the cabinet

Protection PerformanceThe protection performance of an N66E cabinet is described as follows:l The cabinet design takes full account of electromagnetic compatibility (EMC) to ensure an

excellent electromagnetic shielding performance.l The air vents on the bottom plate of the cabinet have air filters installed, which enhance

the dust-proof capability of the N66E cabinet.l The grounding resistance of the N66E cabinet does not exceed 0.1 ohm.

ESD JackWhen wearing an ESD wrist strap, connect the connector of the wrist strap to the ESD jack inthe middle of the N66E cabinet, as shown in Figure 2-7.



21

Figure 2-7 ESD jack on the N66E cabinet

Installation ScenariosAn N66E cabinet can be installed on:l Concrete floorl ESD floor, in which case the N6X series supports are required

Cabinet CombinationN66E cabinets can be installed side by side. When installing N66E cabinets side by side, connectthem using connecting plates, as shown in Figure 2-8.

Figure 2-8 Combined N66E cabinets



22

2.2 N68E CabinetThis section describes the appearance, technical specifications, components, and structuralfeatures of an N68E cabinet.

2.2.1 Appearance of an N68E CabinetAn N68E cabinet complies with the Dimensions of Mechanical Structures of the 482.6 mm (19Inch) Series (IEC 60297-2 Standard). It uses a modular structure, which facilitates expansionand maintenance. The surface of the cabinet and the rack is NC purplish grey.Figure 2-9 shows the appearance of an N68E cabinet.

Figure 2-9 Appearance of an N68E cabinet

2.2.2 N68E Cabinet Physical SpecificationsTable 2-2 lists physical specifications of an N68E cabinet.



23

Table 2-2 N68E cabinet physical specificationsItem SpecificationEmpty cabinet weightNOTE

Empty cabinet weight is the weight of a cabinetwith a front door, a rear door, and two side panels.

100 kg

Dimensions (W x D x H) 600 mm x 800 mm x 2200 mm24 in. x 31 in. x 87 in.

Mounting holes on the top l Position (W x H): 450 mm x 750 mml Nuts: 16 M8 self-clinching nuts

Mounting holes on the bottom l Position (W x H): 413 mm x 687 mml Hole diameter: 18l Nuts: four M12 expansion bolts and

matching nutsDistance between holes on mounting rails When marking the installation positions of a

chassis on mounting rails, count every fourholes with a wide-wide-narrow intervalarrangement as 1 U.Any four adjacent holes on a mounting railmake a distance of 1 U. There are threeinterval arrangements for four adjacent holeson a mounting rail, as shown in Figure 2-10.

Figure 2-10 Interval arrangements for fouradjacent holes

1U

1U

1U

W-W-N W-N-W N-W-W

W: WideN: Narrow

NOTEThe interval between two holes is the distancebetween the axes of the holes.1 U equals 1.75 in. (44.45 mm). U is a unit of heightdefined in International ElectrotechnicalCommission (IEC) 60297.



24

Item SpecificationAvailable space 46 UAngle opening width 450 mmSpace for a chassis (distance between axes ofmounting holes)

465 mm

Distance between a front mounting rail andinterior of the front door

100 mm

Figure 2-11 shows the dimensions of an N68E cabinet.



25

Figure 2-11 N68E cabinet dimensions



26

2.2.3 Components of an N68E cabinetAn N68E cabinet consists of a front door, a rear door, two side panels, and a rack.Figure 2-12 shows the structure of an N68E cabinet.

Figure 2-12 Structure of the N68E cabinet

1 3

243

1 Front door 2 Rear door 3 Side panels 4 Rack

2.2.4 Structural Features of an N68E CabinetThe N68E cabinet has the following structural features: cabinet material, cabling mode, ESDjack, heat dissipation, protection performance, installation scenarios, cabinet combination.

Cabinet MaterialThe N68E cabinet is made of electro-galvanized steel sheets and cold-rolled steel sheetsassembled by screws. The fireproof performance of internal materials complies with thestandards of the Underwriter Laboratories (UL).

Cabling ModeCable apertures are reserved on the top and at the bottom of the N68E cabinet, so that the N68Ecabinet supports overhead cabling and underfloor cabling:



27

l In the overhead cabling mode, external cables enter the cabinet through the top of thecabinet. Figure 2-13 shows the cable apertures.

l In the underfloor cabling mode, external cables enter the cabinet through the bottom of thecabinet.

NOTE

The devices described in this document use the overhead cabling mode.

Figure 2-13 Cable apertures on the cabinet top

312mm

52mm 52mm

Networkcable/fiber

Networkcable/fiber

Power cableReserved holes

312mm

312mm

312mm

145mm65mm 145mm65mm

130mm15mm 130mm15mm

Front Door

ESD JackBefore installing the N68E cabinet, wear an ESD wrist strap and insert connector of the ESDwrist strap into the ESD jack in the middle of the N68E cabinet, as shown in Figure 2-14.



28

Figure 2-14 ESD jack in the middle of the N68E cabinet

Heat DissipationThe front door, rear door, and bottom plate of the N68E cabinet have high-density air vents.Therefore, the N68E cabinet supports front air intake, rear air exhaust, and upper air exhaustand provides good heat dissipation performance.

NOTE

l The devices described in this document adopt left-to-back airflow for heat dissipation.l The airflow of devices described in this document in the cabinet is: front of the cabinet -> left side of

the equipment -> inside the equipment -> rear of the equipment -> rear of the cabinet, as shown inFigure 2-15.



29

Figure 2-15 Airflow in the cabinet

Protection PerformanceThe protection performance of an N68E cabinet is described as follows:l The cabinet design takes full account of electromagnetic compatibility (EMC) to ensure an

excellent electromagnetic shielding performance.l The air vents on the bottom plate of the cabinet have air filters installed, which enhance

the dust-proof capability of the N68E cabinet.l The grounding resistance of the N68E cabinet does not exceed 0.1 ohm.

Installation ScenariosAn N68E cabinet can be installed on:



30

l Concrete floorl ESD floor, in which case the N6X series supports are required

Cabinet CombinationN68E cabinets can be installed side by side. When installing N68E cabinets side by side, connectthem using connecting plates, as shown in Figure 2-16.

Figure 2-16 Combined N68E cabinets



31

3 ChassisAbout This Chapter

3.1 Chassis Models3.2 S97033.3 S97063.4 S9712

S9700 Core Routing SwitchHardware Description 3 Chassis


32

3.1 Chassis ModelsA variety of chassis models are provided to meet diverse customer requirements. Table 3-1 listsS9700 chassis models.Select the chassis models based on your network requirements.

Table 3-1 Chassis modelsDevice Series Chassis

ModelDescription

S9700 S9703 Supports two Main Control Units (MCUs), three LineProcessing Units (LPUs), and AC or DC power modulesin M+N (M + N 2) backup mode.

S9706 Supports two Switching and Routing Units (SRUs), sixLPUs, and AC or DC power modules in M+N (M + N 4) backup mode.

S9712 Supports two SRUs, twelve LPUs, and AC or DC powermodules in M+N (M + N 6) backup mode.

NOTE

l In M+N backup mode, M power modules work as primary power modules, and N power modules workas backup power modules. The configuration requirement is as follows: M x Output power of onepower module > Total power consumption of the equipment, and N is larger than zero. For detailsabout the power module configuration in each chassis, see the slot configuration of each chassis.

l S9700 chassis include FCC-certified chassis and common chassis.

3.2 S9703

3.2.1 Version MappingTable 3-2 describes mapping between the S9703 chassis and software versions.

Table 3-2 Mapping between the S9703 chassis and software versionsChassis VersionS9703 chassis V200R001C00 and later versionsS9703 chassis, FCC certified V200R001C00 and later versions



33

3.2.2 Appearance and Structure

AppearanceThe S9703 chassis is 4 U high (1 U = 44.45 mm). When the chassis has no cable managementframe installed, the dimensions are 442 mm x 489 mm x 175 mm (W x D x H). When the chassishas cable management frames installed, the dimensions are 442 mm x 585 mm x 175 mm (W xD x H). Figure 3-1 and Figure 3-2 show the S9703 chassis.

Figure 3-1 S9703 chassis (front view)

Figure 3-2 S9703 chassis (rear view)

NOTE

The S9703 chassis include FCC-certified chassis and common chassis.

StructureFigure 3-3 and Figure 3-4 show the structure of the S9703 chassis.



34

Figure 3-3 S9703 chassis structure (front view)

1. Rack-mounting bracket (to secure thechassis in a rack)

2. System power module 3. MCU

4. LPU 5. Cable management frame (to arrangecables)

-

Figure 3-4 S9703 chassis structure (rear view)

1. Fan moduleNOTE

Each chassis is configured withonly one fan module. For detailsabout the fan module, see 5.1S9700 Fan Module.

2. Air filterNOTE

It prevents dust from entering thechassis.

3. Double ground screws (toground the chassis)



35

4. ESD jackNOTE

An ESD wrist strap can be insertedinto this ESD jack. ESD preventivemeasures take effect only when thechassis is properly grounded.

- -

3.2.3 Slots

Slot Configuration on the ChassisThe S9703 chassis provides three LPU slots, two MCU slots, and two power slots.Figure 3-5 shows the slot layout on the S9703 chassis, and Table 3-3 describes the slotconfiguration.

Figure 3-5 Slot layout on the S9703 chassis

SLOT1-LPUSLOT4-MCU SLOT5-MCU

PWR1 PWR2

SLOT2-LPU

SLOT3-LPU

Table 3-3 S9703 slot configurationSlot Type Slot ID Module

SupportedRemarks

MCU slot 4 and 5 EH1D2MCUAC00 The distancebetween the twoMCU slots is 0.8inches. The MCUswork in 1+1 backupmode.

LPU slot 1 to 3 Cards supported bythe S9700

The distancebetween twoadjacent slots is 1.4inches.



36

Slot Type Slot ID ModuleSupported

Remarks

Power slot PWR1 and PWR2 l 4.1 2200 W DCPower Module

l 4.2 800 W ACPower Module


These slots cannothave DC and ACpower modulesinstalledsimultaneously, andcannot use AC powermodules withdifferent powervalues together.

Power Slot Configuration

The S9703 chassis have two system power slots: PWR1 and PWR2. The two power slots supportDC and AC power modules, as shown in Figure 3-6.

Figure 3-6 Configuration of S9703 power modules

MCU MCUPWR1 PWR2

LPULPULPU

The following describes the AC and DC power module configurations on an S9703 chassis:l DC power module configuration

S9703 power modules can provide a maximum power of 2200 W, while an S9703 chassisof V200R003C00 or an earlier version consumes less than 1100 W power. Table 3-4 showsthe backup mode of DC power modules.

Table 3-4 Backup mode of DC power modulesPowerModule Type

Active PowerModuleCount (M)

StandbyPowerModuleCount (N)

MaximumPowerProvided

InstallationDescription

2200 W DCpower module

1 N M and M+ N 2

2200 W Install the samepower modulesin power slotsPWR1 andPWR2. Anempty PWRslot must becovered by afiller panel.



37

l AC power module configuration

S9703 power modules can provide a maximum power of 2200 W, while an S9703 chassisof V200R003C00 or an earlier version consumes less than 1100 W power. Table 3-5 showsthe backup mode of AC power modules.

Table 3-5 Backup mode of AC power modulesPowerModule Type





2200 W ACpower module

1 N M and M+ N 2

l 220 V:2200 W

l 110 V:1100 W

Install the samepower modulesin power slotsPWR1 andPWR2. Anempty PWRslot must becovered by afiller panel.


1 l 220 V: 800W

l 110 V: 400W

CAUTIONl When the number of standby power modules is 0, the power modules do not work in backup

mode.l AC and DC power modules or power modules with different power values cannot be installed

simultaneously on a switch.

3.2.4 Power Supply PrinciplesFigure 3-7 shows how DC power modules work on the S9703. Figure 3-8 shows how AC powermodules work on the S9703.



38

Figure 3-7 DC power supply mechanism on the S9703

-48V

DC

PWR1-48/-60V

RTN

BackplaneRTN

DC

PWR2-48/-60V

RTN

RTN

RTN-48V/-60V

Card 2 Card 5

-48V

-48V

Card 1

Figure 3-8 AC power supply mechanism on the S9703

Backplane

AC

PWR1N PGND

-48V

L

RTN

AC

PWR2N PGND

-48V

L

RTN

-48V RTN

Card 2 Card 5Card 1



39

3.2.5 Heat DissipationNOTEIt is recommended that you clean the air filter of a device every six months.

The S9703 cooling system consists of a fan module and an air filter. The fan module is locatedbehind the air exhaust vent (rear of the chassis), and the air filter is located outside the air intakevent (left side of the chassis).l The fan module can intelligently adjust the fan speed. It absorbs cold air into the chassis

to dissipate heat generated by working components, ensuring that the chassis operateswithin a normal temperature range. For details about the performance and attributes of thefan module, see 5.1 S9700 Fan Module.

l The air filter prevents dust from entering the chassis and ensures normal operation of thechassis.

AirflowThe fan module in the S9703 chassis dissipates heat by absorbing air. Air flows from the leftside to the rear of the chassis. Figure 3-9 shows the airflow in the chassis.

Figure 3-9 Airflow in the S9703 chassis

Air FilterThe S9703 uses either a sponge air filter or a waveguide air filter. An FCC-certified chassis mustuse a waveguide air filter. Figure 3-10 shows a sponge air filter, and Figure 3-11 shows awaveguide air filter.

Figure 3-10 Sponge air filter



40

Figure 3-11 Waveguide air filter

The air filter is installed from rear of the S9703 chassis, as shown in Figure 3-12.

Figure 3-12 Installing the S9703 air filter

The air filter is removable. For details on how to remove and install an air filter, see the air filterreplacement instructions in the S9700 Core Routing Switch Parts Replacement.

3.2.6 SpecificationsTable 3-6 lists the specifications of the S9703 chassis.

Table 3-6 S9703 chassis specificationsItem DescriptionBackplane capacity 7.2 Tbit/sLPU slots 3MCU slots 2Fan slots 1System power slots 2VLANs 4KRRPP instances A maximum of 64 Rapid Ring Protection

Protocol (RRPP) ringsSmart Link A maximum of 16 Smart Link groups



41

Item DescriptionMPLS Support for Label Distribution Protocol

(LDP) and Resource Reservation Protocol(RSVP): 8K LDP label switched paths (LSPs)(E series) or 4K LDP LSPs (F series), and 512RSVP LSPs per chassis

MPLS VPN Support for RFC2547bis BGP/MPLS VPN:140,000 routes in each VPN routing andforwarding (VRF) table and a total of140,000 routes in all VRF tables

MPLS VPLS A maximum of 1K virtual switch instances(VSIs) with each VSI supporting themaximum number of MAC address entriesallowed in the system

Routing A maximum of 300K routesMaximum port density 144xFE, 144xGE, 120x10GE, 24x40GECSS Not supportedMaximum power consumption (fully loaded)NOTE

The heat dissipation value of a chassis equals thecurrent power consumption of the chassis.

1100 W

Power specifications l DC input voltage Rated voltage: -48 V DC/-60 V DC Voltage range: -40 V DC to -72 V DC

l AC input voltage Rated voltage: 110 V AC/220 V AC,

50/60 Hz Voltage range: 90 V AC to 290 V AC;

47 Hz to 63 Hz (The output powerreduces to half of the maximum outputwhen the input voltage is in the rangeof 90 V AC to 175 V AC.)

Dimensions (W x D x H, excluding rack-mounting brackets)

l With cable management frames: 442 mmx 585 mm x 175 mm (4 U high)

l Without cable management frames: 442mm x 489 mm x 175 mm (4 U high)

Weight (empty/fully loaded) 11 kg/25 kgReliability and availability l Mean time between failures (MTBF):

33.8 yearsl Mean time to repair (MTTR): 30 minutesl Availability: 0.99999964



42

Item DescriptionEnvironment parameters l Operating temperature and altitude:

-60 m to +1800 m: 0C to 45C 1800 m to 4000 m: Temperature

decreases by 1C every time thealtitude increases 200 m.

4000 m: 0C to 35Cl Operating relative humidity: 5% RH to

95% RH (noncondensing)l Storage temperature: -40C to +70Cl Storage altitude: < 5000 ml Storage relative humidity: 5% RH to 95%

RH (noncondensing)Noise at normal temperature (acoustic power) 72 dBEMC compliance l CISPR22 Class A

l CISPR24l EN55022 Class Al EN50024l ETSI EN 300 386 Class Al CFR 47 FCC Part 15 Class Al ICES 003 Class Al AS/NZS CISPR22 Class Al VCCI Class Al IEC61000-6-2l IEC61000-6-4l IEC61000-4-2l ITU-T K 20l ITU-T K 21l ITU-T K 44l CNS13438 CLASS Al KN 22 CLASS A

Environmental standards compliance l RoHSl REACH

Safety standards compliance l IEC 60950-1l EN 60950-1l UL 60950-1l CSA C22.2 No 60950-1l AS/NZS 60950.1l BS EN 60950-1



43

Method for Calculating the Interface CapacityInterface capacity = Maximum interface rate x Interface densityl The maximum interface rate is the highest transmission rate of a single interface.l The interface density is the number of a specified type of interfaces on the chassis.Each S9703 LPU provides a maximum of 40 10GE interfaces, and each S9703 chassis provides3 LPU slots. A chassis can provide a maximum of 120 10GE interfaces. That is, the interfacedensity is 120. The transmission rate of each 10GE interface is 10 Gbit/s; therefore, the interfacecapacity of the S9703 is 1200 Gbit/s.

3.3 S9706




AppearanceThe S9706 chassis is 10 U high (1 U = 44.45 mm). When the chassis has no cable managementframe installed, the dimensions are 442 mm x 489 mm x 441.7 mm (W x D x H). When thechassis has cable management frames installed, the dimensions are 442 mm x 585 mm x 441.7mm (W x D x H). Figure 3-13 and Figure 3-14 show the S9706 chassis.



44



NOTE

S9706 chassis include FCC-certified chassis or common chassis.




45


7

1. LPU 2. SRU 3. Rack-mounting bracket (to secure thechassis in a rack)

4. Cable management frame (to arrangecables)

5. CMU 6. System power module

7. ESD jackNOTE

An ESD wrist strap can be inserted into thisESD jack. ESD preventive measures take effectonly when the chassis is properly grounded.

- -



46


1. Air filter (to prevent dustfrom entering the chassis)

2. Fan moduleNOTE

Each chassis is configured withtwo fan modules. For details aboutthe fan modules, see 5.1 S9700Fan Module.


4. ESD jackNOTE

An ESD wrist strap can beinserted into this ESD jack. ESDpreventive measures take effectonly when the chassis is properlygrounded.

- -

3.3.3 Slots

Slot Configuration on the ChassisThe S9706 chassis provides six LPU slots, two SRU slots, two CMU slots, and four power slots.Figure 3-17 shows the slot layout on the S9706 chassis, and Table 3-8 describes the slotconfiguration.



47


PWR1

PWR2

PWR3

PWR4

CMU1

CMU2

SLOT1-LPUSLOT2-LPUSLOT3-LPU


SLOT7-SRUSLOT8-SRU


SupportedRemarks

SRU slot 7 and 8 l EH1D2SRUC000

l EH1D2SRUDC00/EH1D2SRUDC01

The distancebetween the twoSRU slots is 0.8inches. The SRUswork in 1+1 backupmode.



CMU slot CMU1 and CMU2 EH1D200CMU00 The CMUs work inhot standby mode.

Power slot PWR1 to PWR4 l 4.1 2200 W DCPower Module



DC and AC powermodules or ACpower modules withdifferent powervalues cannot beinstalledsimultaneously in thepower slots.

Power Slot ConfigurationThe S9706 chassis provides four power slots: PWR1 to PWR4. These power slots support DCand AC power modules, as shown in Figure 3-18.



48


CMU1

CMU2

PWR2

PWR3

PWR4

PWR1

LPULPULPU

LPULPULPU

SRUSRU

The following describes the AC and DC power module configurations on an S9706 chassis:l AC power module configuration

S9706 power modules can provide a maximum power of 4400 W, while a chassis runningV200R003C00 or an earlier version consumes less than 2200 W of power. Table 3-9 showsthe backup mode of DC power modules.







M 2 N M M*2200 W Install the samepower modulesin PWR1 toPWR4. Anempty PWRslot must becovered by afiller panel.

l DC power module configuration

An S9706 system provides a maximum power of 4400 W while a chassis runningV200R003C00 or an earlier version consumes less than 2200 W of power. Table 3-10shows the backup mode of AC power modules.



49







M 2 N M and M+ N 4

l 220 V:M*2200 W

l 110 V:M*1100 W

Install the samepower modulesin PWR1 toPWR4. Anempty PWRslot must becovered by afiller panel.


M 4 l 220 V:M*800 W

l 110 V:M*400 W

CAUTIONl When the number of standby power modules is 0, the power modules do not work in backup

mode.l AC and DC power modules or power modules with different power values cannot be installed

simultaneously on a switch.

3.3.4 Power Supply PrinciplesFigure 3-19 shows how DC power modules work on the S9706. Figure 3-20 shows how ACpower modules work on the S9706.



50

Figure 3-19 DC power supply mechanism on the S9706

-48V

DC

PWR1-48/-60V

RTN

BackplaneRTN -48V

DC

PWR2-48/-60V

RTN

RTN

DC

PWR4-48/-60V

RTN

RTN

RTN-48V/-60V

Card 1 Card 2 Card 10

-48V

-48V

Figure 3-20 AC power supply mechanism on the S9706

Backplane

AC

PWR1N PGND

-48V

L

RTN

AC

PWR2N PGND

-48V

L

RTN

-48V RTN

AC

PWR4N PGND

-48V

L

RTN

Card 1 Card 2 Card 10



51

3.3.5 Heat DissipationNOTE

It is recommended that you clean the air filter of a device every six months.

The S9706 cooling system consists of two fan modules and one air filter. The fan modules arelocated behind the air exhaust vent (rear of the chassis), and the air filter is located outside theair intake vent (left side of the chassis).l The fan modules can intelligently adjust the fan speed. They absorb cold air into the chassis

to dissipate heat generated by working components, ensuring that the chassis operateswithin a normal temperature range. For details about the performance and attributes of thefan modules, see 5.1 S9700 Fan Module.

l The air filter prevents dust from entering the chassis and ensures normal operation of thechassis.

AirflowThe fan modules in the S9706 chassis dissipate heat by absorbing air. Air flows from the leftside to the rear of the chassis. Figure 3-21 shows the airflow in the chassis.

Figure 3-21 Airflow in the S9706 chassis

Fan ZonesThe S9706 is divided into multiple zones. If there are empty slots in a zone, the fanscorresponding to this zone operate at a low speed, which reduces power consumption and noises.As shown in Figure 3-22, two fan modules of the S9706 serve two zones, with four cards ineach zone.



52

Figure 3-22 S9706 fan zones

CMU1

CMU2



SLOT7-SRUSLOT8-SRU

Zone 1

Zone 2

Air FilterThe S9706 uses either a sponge air filter or a waveguide air filter. An FCC-certified chassis mustuse a waveguide air filter. Figure 3-23 shows a sponge air filter, and Figure 3-24 shows awaveguide air filter.

Figure 3-23 Sponge air filter



53

Figure 3-24 Waveguide air filter

The air filter is installed from rear of the S9706 chassis, as shown in Figure 3-25.

Figure 3-25 Installing the S9706 air filter

The air filter is removable. For details on how to remove and install an air filter, see the air filterreplacement instructions in the S9700 Core Routing Switch Parts Replacement.

3.3.6 SpecificationsTable 3-11 lists the specifications of the S9706 chassis.

Table 3-11 S9706 specifications chassisItem DescriptionBackplane capacity 14.4 Tbit/sLPU slots 6SRU slots 2



54

Item DescriptionFan slots 2System power slots 4CMU slots 2Maximum port density 288xFE, 288xGE, 240x10GE, 48x40GEVLANs 4KRRPP instances A maximum of 64 Rapid Ring Protection

Protocol (RRPP) ringsSmart Link A maximum of 16 Smart Link groupsMPLS Support for Label Distribution Protocol

(LDP) and Resource Reservation Protocol(RSVP): 8K LDP label switched paths (LSPs)(E series) or 4K LDP LSPs (F series), and 512RSVP LSPs per chassis

MPLS VPN Support for RFC2547bis BGP/MPLS VPN:500,000 routes in each VRF table and a totalof 500,000 routes in all VRF tables

MPLS VPLS A maximum of 1K virtual switch instances(VSIs) with each VSI supporting themaximum number of MAC address entriesallowed in the system

Routing A maximum of 1M routesInstallation N66E or N68E cabinet, two chassis in each

cabinetCSS CSS setup using service ports or CSS cardsMaximum power consumption (fully loaded)NOTE

The heat dissipation value of a chassis equals thecurrent power consumption of the chassis.

2200 W

Power specifications l DC input voltage Rated voltage: -48 V DC/-60 V DC Voltage range: -40 V DC to -72 V DC

l AC input voltage Rated voltage: 110 V AC/220 V AC,

50/60 Hz Voltage range: 90 V AC to 290 V AC;

47 Hz to 63 Hz (The output powerreduces to half of the maximum outputwhen the input voltage is in the rangeof 90 V AC to 175 V AC.)



55

Item DescriptionDimensions (W x D x H, excluding rack-mounting brackets)

l With cable management frames: 442 mmx 585 mm x 441.7 mm (10 U high)

l Without cable management frames: 442mm x 489 mm x 441.7 mm (10 U high)

Weight (empty/fully loaded) 29 kg/45 kgReliability and availability l MTBF: 24.2 years

l MTTR: 30 minutesl Availability: 0.99999959

Environment parameters l Operating temperature and altitude: -60 m to +1800 m: 0C to 45C 1800 m to 4000 m: Temperature

decreases by 1C every time thealtitude increases 200 m.

4000 m: 0C to 35Cl Operating relative humidity: 5% RH to

95% RH (noncondensing)l Storage temperature: -40C to +70Cl Storage altitude: < 5000 ml Storage relative humidity: 5% RH to 95%

RH (noncondensing)Noise at normal temperature (acoustic power) 72 dBEMC compliance l CISPR22 Class A

l CISPR24l EN55022 Class Al EN50024l ETSI EN 300 386 Class Al CFR 47 FCC Part 15 Class Al ICES 003 Class Al AS/NZS CISPR22 Class Al VCCI Class Al IEC61000-6-2l IEC61000-6-4l IEC61000-4-2l ITU-T K 20l ITU-T K 21l ITU-T K 44l CNS13438 CLASS Al KN 22 CLASS A



56

Item DescriptionEnvironmental standards compliance l RoHS

l REACHSafety standards compliance l IEC 60950-1

l EN 60950-1l UL 60950-1l CSA C22.2 No 60950-1l AS/NZS 60950.1l BS EN 60950-1

Method for Calculating the Interface CapacityInterface capacity = Maximum interface rate x Interface densityl The maximum interface rate is the highest transmission rate of a single interface.l The interface density is the number of a specified type of interfaces on the chassis.Each S9706 LPU provides a maximum of 40 10GE interfaces, and each S9706 chassis provides6 LPU slots. A chassis can provide a maximum of 240 10GE interfaces. That is, the interfacedensity is 240. The transmission rate of each 10GE interface is 10 Gbit/s; therefore, the interfacecapacity of the S9706 is 2400 Gbit/s.

3.4 S9712




AppearanceThe S9712 chassis is 15 U high (1 U = 44.45 mm). When the chassis has no cable managementframe installed, the dimensions are 442 mm x 489 mm x 663.95 mm (W x D x H). When the



57

chassis has cable management frames installed, the dimensions are 442 mm x 585 mm x 663.95mm (W x D x H). Figure 3-26 and Figure 3-27 show the S9712 chassis.




58


NOTE

S9712 chassis include FCC-certified chassis or common chassis.




59


7

1. LPU 2. SRU 3. Rack-mounting bracket (to secure thechassis in a rack)

4. Cable management frame (to arrangecables)

5. CMU 6. System power module

7. ESD jackNOTE

An ESD wrist strap can be inserted into thisESD jack. ESD preventive measures take effectonly when the chassis is properly grounded.

- -



60


1. Air filter (to prevent dustfrom entering the chassis)

2. Fan moduleNOTE

Each chassis is configured withfour fan modules. For detailsabout the fan modules, see 5.1S9700 Fan Module.


4. ESD jackNOTE

An ESD wrist strap can beinserted into this ESD jack. ESDpreventive measures take effectonly when the chassis is properlygrounded.

- -

3.4.3 Slots



61

Slot Configuration on the ChassisThe S9712 chassis provides twelve LPU slots, two SRU slots, two CMU slots, and six powerslots.Figure 3-30 shows the slot layout on the S9712 chassis, and Table 3-13 describes the slotconfiguration.


PWR1

PWR2

PWR3

PWR4

CMU1

CMU2

SLOT1-LPUSLOT2-LPUSLOT3-LPUSLOT4-LPUSLOT5-LPUSLOT6-LPU


SLOT10-LPUSLOT11-LPU

SLOT12-LPU

SLOT13-SRUSLOT14-SRU

PWR5

PWR6


SupportedRemarks

SRU slot 13 and 14 l EH1D2SRUC000

l EH1D2SRUDC00/EH1D2SRUDC01

The distancebetween the twoSRU slots is 0.8inches. The SRUswork in 1+1 backupmode.



62

Slot Type Slot ID ModuleSupported

Remarks



CMU slot CMU1 and CMU2 EH1D200CMU00 The CMUs work inhot standby mode.

Power slot PWR1 to PWR6 l 4.1 2200 W DCPower Module



DC and AC powermodules or ACpower modules withdifferent powervalues cannot beinstalledsimultaneously in thepower slots.

Power Slot ConfigurationThe S9712 chassis provides six power slots: PWR1 to PWR6. These power slots support DCand AC power modules, as shown in Figure 3-31.


CMU1

CMU2

PWR2

PWR3

PWR4

PWR5

PWR6

PWR1

LPULPULPULPULPULPU

LPULPULPULPULPULPU

SRUSRU



63

The following describes the AC and DC power module configurations on an S9712 chassis:l DC power module configuration

S9712 power modules can provide a maximum power of 6600 W, while a chassis runningV200R003C00 or an earlier version consumes less than 4400 W of power. Table 3-14shows the backup mode of DC power modules.







M 3 N M M*2200 W Install the samepower modulesin PWR1 toPWR6. Anempty PWRslot must becovered by afiller panel.

l AC power module configuration

S9712 power modules can provide a maximum power of 6600 W, while a chassis runningV200R003C00 or an earlier version consumes less than 4400 W of power. Table 3-15shows the backup mode of AC power modules.







M 3 N M and M+ N 6

l 220 V:M*2200 W

l 110 V:M*1100 W

Install the samepower modulesin PWR1 toPWR6. Anempty PWRslot must becovered by afiller panel.


2 M 6 l 220 V:M*800 W

l 110 V:M*400 W


Issue 04 (2013-05-30) Huawei Proprietary and Confiden

Documents

HUAWEI S9700 Switch Hardware Description