Embed Size (px)
Citation preview
LOT QTY DESCRIPTION1 1 C-FRAME PRESS, GREENERD 8 T. CAP. MDL. HA-8-
8L2, 15" STROKE, 925" THROAT, 5 HP MOTOR, 230/460/3/60, 24 GAL. RESERVOIR CAP. (LOCATION B)
2 1 C-FRAME PRESS, GREENERD 5 T. CAP. MDL. HPB-5, 14" X 10" BED, 6" STROKE ADJ., 12" DAYLIGHT, 7" THROAT, 1-3/8" DIA. RAM, 2-1/2" CYL. BORE, 3 HP MOTOR, S/N 92T4549 (LOCATION A)
3 1 ABRASIVE CHOP SAW, KALAMAZOO 20" (LOCATION A)
4 1 HYDRAULIC ABRASIVE SAW, EVERETT MDL. 20-22, 2,230 RPM, 20 HP MOTOR, 230/460/3/60, 20" WHEEL, HYD. BLADE FEED (LOCATION B)
5 1 ABRASIVE CUT-OFF SAW, MASON-MATE MASONRY TYPE, 3 HP ELECTRIC MOTOR (LOCATION A)
5A 1 HORIZONTAL BANDSAW, MDL. G5012W (LOCATION B)
6 1 COMBINATION SANDER, DAYTON MDL. 4TJ97, 6" BELT, 12" DISC (LOCATION A)
7 1 COMBINATION SANDER, DAYTON MDL. 4TJ97, 6" BELT, 12" DISC (LOCATION A)
8 1 SPEED/POLISHING LATHE, SCHAUER TYPE NA 2C, 550/3/60, (2) SPDS: 1 HP MOTOR/1,725 RPM/1.4 AMPS & 1 HP MOTOR/3,450 RPM/1.1 AMPS, 44" HT. X 20"W. (LOCATION B)
9 1 SPEED/POLISHING LATHE, SCHAUER TYPE NA 2C, 550/3/60, (2) SPDS: 1 HP MOTOR/1,725 RPM/1.4 AMPS & 1 HP MOTOR/3,450 RPM/1.1 AMPS, 44" HT. X 20"W. (LOCATION B)
10 1 DUAL WHEEL CARBIDE TOOL GRINDER, HAMMOND MDL. 14-WD, 9" X 22" TABLE, 3 HP, S/N 8896 (LOCATION B)
11 1 DUAL WHEEL CARBIDE TOOL GRINDER, CUSTOM 10", 14"W. TABLE, 1.5 HP (LOCATION B)
12 1 DUAL WHEEL CARBIDE TOOL GRINDER, XLO 10" MDL. 48B, 1 HP MOTOR (LOCATION B)
13 1 H.D. WET/DRY PEDESTAL GRINDER, BROWN & BROCKMEYER, 12" DUAL WHEEL, 2 HP MOTOR, 220/440/3/60, 1,750 RPM, 6/3 AMPS (LOCATION B)
HOUSTON MULTI LOCATION DECEMBER AUCTION
15 1 PEDESTAL GRINDER, LINNS, 10" CAP. WHEEL, 18" DIST. CENTER TO CENTER OF WHEELS, 45" DIST. FLOOR TO TABLE TOP, 3-1/2" X 1-1/2" TABLE, 1 HP MOTOR, S/N 197677294 (LOCATION A)
17 1 WET/DRY BELT GRINDER, PORTER CABLE MDL. BG8, 8" TO 9" BELT WIDTH, 7.5" X 11.25" WORKTABLE, COOLANT BASE, CHIP DRAWER, 5 HP MOTOR, 220/3/60 (LOCATION B)
18 1 DOUBLE END PEDESTAL GRINDER, CENTRAL MACHINERY, 2 HP, 1,750 RPM, 10" GRINDING (LOCATION A)
18A 1 DOUBLE END PEDESTAL GRINDER, DAYTON, 3/4 HP MOTOR, 3,450 RPM, 115 v. (LOCATION A)
18B 1 DOUBLE END PEDESTAL GRINDER, CINCINNATI TYPE PBA-Y, 1/3 HP MOTOR, 6" WHEELS (LOCATION B)
18C 1 BENCH GRINDER, CRAFTSMAN, 3/4 HP MOTOR, 6" WIRE WHEELS, WORKLIGHT (LOCATION B)
19 1 DOUBLE END H.D. BUFFER, SETCO MDL. 222-205 (LOCATION A)
20 1 FLEXIBLE SHAFT GRINDER, STRANDED MDL. DD6, 115 v., 1/2 HP MOTOR, ON CASTERS (LOCATION B)
21 1 DRILL PRESS, DELTA MDL. 15-263 (LOCATION A)
22 1 DRILL PRESS, DELTA, S/N 114-8632 (LOCATION A)
23 1 DRILL PRESS, POWERMATIC MDL. 1150, S/N 415V1482 (LOCATION A)
24 1 NOISELESS RIVETER, TAUMEL MDL. BK100, 220/440/3/60 (LOCATION B)
25 1 HYDRAULIC NUT SPLITTER, HKN MDL. 1790PQ, FOR SOFT NUTS UP TO 1-7/8" ROCKWELL C-15 (LOCATION A)
26 1 FLOOR TYPE DRILL PRESS, DELTA MDL. 14-070, S/N R9240 (LOCATION B)
26A 1 FLOOR TYPE DRILL PRESS, DELTA MDL. 17-900, S/N R9039 (LOCATION B)
26B 1 FLOOR TYPE DRILL PRESS, YUASA MDL. AX-58F, S/N 521821 (LOCATION B)
27 LOT LARGE C-CLAMPS (LOCATION B)28 LOT LARGE C-CLAMPS (LOCATION B)
28A LOT C-CLAMPS (LOCATION B)
29 1 RIGHT ANGLE GRINDER, ELECTRIC, 4" (LOCATION A)
29A LOT 1/2" NUT DRIVERS, CHICAGO PNEUMATIC & IRR (LOCATION A)
30 1 RECIPROCATING SAW, MILWAUKEE SAWZALL, w/CASE (LOCATION A)
30A 1 RECIPROCATING SAW, MILWAUKEE SAWZALL, w/CASE (LOCATION A)
30B 1 RECIPROCATING SAW, MILWAUKEE SAWZALL, w/CASE (LOCATION A)
30C 1 RECIPROCATING SAW, w/SOFT CASE (LOCATION A)
30D 1 RECIPROCATING SAW, DEWALT, w/CASE (LOCATION A)
31 1 PORTA BANDSAW, MILWAUKEE, w/CASE (LOCATION A)
31A 1 PORTA BANDSAW, MILWAUKEE, w/CASE (LOCATION A)
31B 1 PORTA BANDSAW, PORTER CABLE (LOCATION A)
31C 1 PORTA BANDSAW, MILWAUKEE (LOCATION A)32 1 RECHARGEABLE DRILL, MILWAUKEE, 18 v.,
w/CHARGER & CASE (LOCATION A) 32A 1 RECHARGEABLE DRILL, DEWALT, w/CHARGER &
CASE (LOCATION A) 32B 1 RECHARGEABLE DRILL, DEWALT, w/CHARGER &
CASE (LOCATION A) 32D 1 ELECTRIC DRILL, KAWASAKI 3/8" (LOCATION A)
33 1 NUT DRIVER, CRAFTSMAN 1/2" (LOCATION A) 33A 1 NUT DRIVER, DEWALT 1/2" (LOCATION A) 33B 1 NUT DRIVER, MILWAUKEE 1/2" (LOCATION A) 33C 1 NUT DRIVER, CHICAGO ELECTRIC 1/2" (LOCATION A)
34 1 ABRASIVE CHOP SAW, RIDGID (LOCATION A) 34A 1 ABRASIVE CHOP SAW, RIDGID (LOCATION A) 34B 1 ABRASIVE CHOP SAW, DEWALT (LOCATION A)35 1 ABRASIVE CUT-OFF SAW, PORTABLE, STIHL,
GASOLINE PWRD. (LOCATION A) 36 1 BANDING CART, w/STAPS, BANDING TOOLS, CLIPS,
STRETCH WRAP DISPENSER (LOCATION A)
37 LOT PIPE WRENCHES (LOCATION A)37A LOT PIPE WRENCHES (LOCATION A)38 LOT PALLET, w/OXY./ACY. HOSE & GAUGES (LOCATION
A) 39 LOT TIE-DOWN STRAPS (LOCATION A)
40 LOT C-CLAMPS (LOCATION A) 40A LOT C-CLAMPS (LOCATION A) 40B LOT C-CLAMPS (LOCATION A) 41 1 PLATFORM SCALE, HOWE 1,000 LB. CAP. (LOCATION
B)42 LOT ROLLING TOOL CABINETS, MAC TOOL (LOCATION B)
43 LOT TOOL CABINETS: MATCO & SNAP-ON (LOCATION B)
44 LOT SHOP FANS: BOX & PEDESTAL (LOCATION B)44A 1 HOT WATER PRESSURE WASHER, DAYTON HOTSY
MDL. 5832A, 360 GPM, 1,800 PSI, 7.5 HP MOTOR, S/N H28349 (LOCATION A)
45 1 DAYTON HOTSY HOT WATER PRESSURE WASHER & RIDGID SHOP VACUUM (LOCATION B)
46 1 SHOP HEATER, REDDYHEATER, KEROSENE FIRED, 170,000 BTU (LOCATION B)
47 1 TORCH CART, HOSE & GAUGE, 15" TIRES (LOCATION B)
48 1 TORCH CART, w/ACET. BOTTLE (LOCATION B) 49 1 PIPE TRISTAND TRIPOD, RIDGID MDL. 40A
(LOCATION B)50 LOT SAFETY SUPPLIES: RESPIRATOR, HARD HATS,
HARNESSES & MASK, STORAGE CABINET (LOCATION A)
51 LOT STEPLADDERS, (3) 12' & (1) 6' (LOCATION A)52 1 WHEELBARROW, TRUE TEMPER (LOCATION A)53 LOT ELECTRICAL EXTENSION CORDS (LOCATION A)54 LOT SHOVELS & BROOMS (LOCATION A)55 1 PNEUMATIC JACK HAMMER, TEXAS PNEUMATICS,
w/TOOLING (LOCAITON A)56 1 HAMMER DRILL, DEWALT, w/TOOLS (LOCATION A)
57 1 HAMMER DRILL, DEWALT, w/CASE & BITS (LOCATION A)
58 1 HAMMER DRILL, BOSCH, w/CASE & BITS (LOCATION A)
59 1 CIRCULAR SAW, MAKITA, w/CASE (LOCATION A)
59A 1 CIRCULAR SAW, SKILSAW 7-1/4" (LOCATION A)
59B 1 CIRCULAR SAW, MILWAUKEE 7-1/2" (LOCATION A)
59C 1 CIRCULAR SAW, SKILSAW WORM DRIVE (LOCATION A)
60 1 SADDLE TYPE TURRET LATHE, WARNER & SWASEY 5A MDL. 3600 SQUARE HEAD, 36.5" SW. OVER WAYS, 144" MAX. DIST. CHUCK FACE TO TURRET FACE, LEAD-ON THREADING ON TURRET, WARNER & SWASEY HYD. SHIFTING HEADSTOCK, SPDS: 10-281 RPM, 12.5 HOLE THROUGH SPDL., A1-20 SPDL. NOSE, 50 HP MAIN MOTOR, 440/3/60, 28" DIA. 4-JAW CHUCK, REAR CROSSLIDING HEX TURRET, PWR. FEEDING COMPOUND ON FRONT CARRIAGE, 4' EXTRA BED LENGTH, ASSORTED FLANGED TOOLHOLDERS, 26" DIA. FIXED STEADYREST, (2) H.D. BORING BARS, LOW HRS., S/N 2316558 (LOCATION B)
61 1 SADDLE TYPE TURRET LATHE, WARNER & SWASEY 4A MDL. 1500, CROSSLIDING REAR TURRET, 28.5" SW. OVER BED, SPDS: 14-319 RPM, 9-1/4" SPDL. HOLE, 68" SPDL. NOSE TO TURRET FACE, 30 HP, 220/440/3/60, ASSORTED FLANGED TOOLHOLDERS (NO FRONT CARRIAGE, MISSING ELECTRICAL CABINET) (LOCATION B)
62 1 PRECISION TURRET LATHE, HARDINGE MDL. DV-59, 9" SW. OVER BED, 1.5 HP MOTOR, 220/3/60, PROD. CROSSLIDE, COLLET CLOSER w/5C ADAPTER, 5C COLLETS, COOLANT PUMP, LEVER OPERATED HEX TURRET WITH 5/8" DIA. HOLES, 5" DIA. 3-JAW CHUCK, (2) DRILL CHUCKS (LOCATION B)
63 1 GAP BED ENGINE LATHE, BINNS & BERRY 40" X 171" MDL. TRIDENT 1000, NEW 1988, 40" SW. OVER BED, 33.5" SW. OVER CROSSLIDE, 171" BTN. CENTERS, 59" SW. IN GAP, 17.8" L. GAP, SPDL. SPDS. (IN 3 RANGES): 50-550 RPM, 10-260 RPM & 1.5-50 RPM, 16" PWR. TOP SLIDE TRAVEL, 6" HOLE THROUGH SPDL., A2-15 SPDL., 30 HP MOTOR, (2) STEADYRESTS, 36" DIA. 4-JAW FRONT & 18" DIA. 4-JAW REAR CHUCK, RAPID TRAVERSE TO CARRIAGE & CROSSLIDE, 3-WAY BED ALLOWS CARRIAGE TO PASS TAILSTOCK, HARDENED & GROUND FRONT & CENTER WAYS, CHUCK GUARDS (LOCATION B)
64 1 GAP BED ENGINE LATHE, LEBLOND 25" X 156" MDL. 2516, 38" SW. IN GAP, SPDL. SPDS: 12-1500 RPM, FDS: .002-.410 IPR, 20 HP MOTOR, 220/440/3/60, HARD REPLACEABLE BED & CROSSLIDE WAYS, TAPER, COOLANT, 21" DIA. 4-JAW CHUCK, 15" DIA. 3-JAW CHUCK, 9" STEADYREST, LONGITUDINAL RAPIDS (LOCATION B)
65 1 GAP BED ENGINE LATHE, PROFITMASTER 17" X 80", APPROX. 9" SW. OVER CROSSLIDE, 24" SW. IN GAP, 2-1/2" SPDL. HOLE, SPDS: 20-2000 RPM, INCH/METRIC THDNG., TAPER ATTACH., 15" DIA. 4-JAW CHUCK, 16" DIA. 4-JAW CHUCK, 12" DIA. 3-JAW CHUCK, 12" FACEPLATE, PWR. RAPID TRAVERSE, S/N 8211 (LOCATION A)
66 1 ENGINE LATHE, LEBLOND 25" X 120" MDL. HD20, 25.5" SW. OVER BED, 15" SW. OVER CROSSLIDE, SPDL. SPDS: 10-1300 RPM, THREADS: 1 TO 60 TPI, FEEDS: .0045 TO .269 IPR, CUSHMAN 21" DIA. 4-JAW CHUCK, #6 MT TAILSTOCK, LENGTH READING DIAL ON TAILSTOCK, TAPER ATTACH., MICROMETER CARRIAGE STOP, 30 HP, 460/3/60, 22.5" WIDTH ACROSS BEDWAYS, HARDENED & REPLACEABLE BEDWAYS, WEIGHT APPROX. 17,000 LBS. (MISSING QUICK CHANGE HANDLE AVAILABLE AT LEBLOND LTD.) (LOCATION B)
67 1 ENGINE LATHE, MONARCH 20" X 78" MDL. 2013 SERIES 62, 20" SW. OVER BED, 13" SW. OVER CROSSLIDE, 78" DIST. BTN. CENTERS, 2-1/16" SPDL. HOLE, (36) SPDL. SPDS: 14-1750 RPM, 15 HP, STEADYREST, TAILSTOCK, S/N 47566 (LOCATION A)
68 1 ENGINE LATHE, AXELSON 20" X 48" MDL. 20-D, 22.5" SW. OVER BED, 13.5" SW. OVER CROSSLIDE, 48" CENTERS, (24) SPDL. SPDS: 9.5-961 RPM, THREADING, CAMLOCK D1-8 SPDL. NOSE, 2-3/16" SPDL. HOLE, 22" w/WAYS, 20 HP, 220/440/3/60, TAPER, HARDENED & REPLACEABLE WAYS, TAILSTOCK, COOLANT, 22" FACEPLATE, LEVELING PADS, CUSHMAN 15" DIA. 3-JAW CHUCK, S/N 4138 (LOCATION B)
69 1 ENGINE LATHE, AXELSON 20" X 48" MDL. 20-D, 22.5" SW. OVER BED, 13.5" SW. OVER CROSSLIDE, 48" CENTERS, (24) SPDL. SPDS: 9.5-961 RPM, THREADING, CAMLOCK D1-8 SPDL. NOSE, 2-3/16" SPDL. HOLE, 22" w/WAYS, 20 HP, 220/440/3/60, TAPER, HARDENED & REPLACEABLE WAYS, TAILSTOCK, COOLANT, 22" FACEPLATE, LEVELING PADS, SKINNER 15" DIA. 3-JAW CHUCK, S/N 4145 (LOCATION B)
70 1 TOOLROOM LATHE, MONARCH 16" X 54" MDL. 16, SERIES 50, 11" SW. OVER CROSSLIDE, SPDS: 30-1800 RPM, 1-3/4" HOLE, CAMLOCK D1-6 SPDL. NOSE, #4 MT TAILSTOCK, 10 HP, 230/3/60, TAPER, ALORIS TOOLPOST & HOLDERS, FOLLOWREST, 12" DIA. 4-JAW CHUCK, 12" DIA. 3-JAW CHUCK, 13" FACEPLATE (LOCATION B)
71 1 ENGINE LATHE, LEBLOND 15" X 54" REGAL SERVO SHIFT, D1-6 CAMLOCK, SPDL. SPDS: 45-1800 RPM, INCH/METRIC THDNG., 2-1/2" HOLE, 7.5 HP MOTOR, 10" DIA. 3-JAW CHUCK, TAPER, MICROMETER CARRIAGE STOP, STEADY, COOLANT SYS. (LOCATION B)
72 1 ENGINE LATHE, AMERICAN PACEMAKER 14" X 78", 17" SW. OVER BED, 1-3/4" HOLE, L1 SPDL. NOSE, SPDL. SPDS: 17-1000 RPM, THREADING, 5 HP MOTOR, 230 v/3 PH, 12" DIA. 4-JAW CHUCK, 10" DIA. 3-JAW CHUCK, TAPER, 6" STEADY, S/N 66377-43 (LOCATION B)
73 1 TOOLROOM LATHE, AMERICAN 21" X 78" MDL. BCDL, 13" SW. OVER CROSSLIDE, SPDS: 15-1000 RPM, THREADING, 20 HP MOTOR, 230/460/3/60, D1-6 CAMLOCK SPDL. NOSE, 2" HOLE, #4 MORSE TAPER, TAPER ATTACH., COOLANT (LOCATION B)
74 1 TOOLROOM LATHE, SOUTHBEND 13" X 20" MDL. CL-1307, 7" SW. OVER CROSSLIDE, 4,000 RPM, VARIABLE SPDL. SPDS., 1-3/8" SPDL. HOLE, 5 HP MOTOR, STEADYREST, S/N 72 SP 132 (LOCATION A)
75 1 TOOLROOM LATHE, MONARCH 12-1/2" X 20" MDL. EE, NEW 1986, GOV'T REBUILD 1994, 7-1/4" SW. OVER CROSSLIDE, VARIABLE SPDL. SPDS: 5-4000 RPM, 1-13/32" SPDL. HOLE, D1-3 CAMLOCK SPDL. NOSE, INCH/METRIC THREADING & FEEDS, 5 HP, 460 v., TAPER, CUSHMAN 6" DIA. CHUCK (LOCATION B)
76 1 ENGINE LATHE, SOUTHBEND 9" X 24", 31.5" BED, 5" SW. OVER CROSSLIDE, VARIABLE SPDL. SPDS: 0-2500 RPM, COLLET CLOSER, (32) COLLETS TO 1/2", 5" DIA. 3-JAW & 6" DIA. 4-JAW, 3" STEADYREST, ALORIS TOOLPOST & HOLDERS, BENCH, CATALOG NO. 6702 (LOCATION B)
77 1 VERTICAL BORING MILL, TOS 66", 72" MAX. SWING, 72" MAX. HEIGHT UNDER RAIL, TURRET RAM & SIDE HEADS, THDNG: 3.5-150 RPM (LOCATION A)
78 1 CNC VERTICAL TURRET LATHE, GIDDINGS & LEWIS 52", GIDDINGS & LEWIS 800 4-AXIS CNC CONTROL, 52" DIA. TABLE, 62" SWING, 45" HEIGHT UNDER RAIL, 29" RAIL TRAVEL, 33" TURRET HEAD VERT. TRAVEL, TABLE SPDS: 3-272 RPM, 50 HP MOTOR, CHIP CONVEYOR, S/N 500-57-64 (LOCATION A)
79 1 VERTICAL TURRET LATHE, BULLARD 42" SPIRAL DRIVE, 42" DIA. 4-JAW CHUCK, SIDE HEAD, SPDS: 4.1-93 RPM, 36" UNDER RAIL, 46" MAX. SWING w/SIDE HEAD BELOW TABLE, 15 HP, 220/440/3/60, S/N 12793 (WAYS NOT SCORED, MISSING FLAT BED FOR FEED DRIVE) (LOCATION B)
80 1 VERTICAL MILL, CINCINNATI VERCIPOWER MDL. 650, 20" X 104" TABLE, 50" TABLE TRAVEL, 18" SADDLE CROSS TRAVEL, 28" VERT. HEAD TRAVEL, SPDL. SPDS: 14-1400 RPM, FDS: 3/8" TO 90 IPM, #50 SPDL. TAPER, 3" QUILL ADJ., 50 HP, 230/460/3/60, OUTBOARD TABLE SUPPTS., RAPID TRAVERSE IN ALL DIRECTIONS, PWR. TOOL LOCK (LOCATION B)
81 1 CNC VERTICAL MILL, HURCO MDL. KM3P, HURCO CNC CONTROL, TABLE 14" X 49" OVERALL/10" X 38" WORK SURFACE, 24" LONG. TRAVEL, 13.7" CROSS TRAVEL, 15.5" KNEE TRAVEL, 750 LBS. TABLE CAP., 14" RAM TRAVEL, VARIABLE SPDL. SPDS: 60-4000 RPM, 5" QUILL TRAVEL, 3 HP MOTOR, S/N KD8-8015129E (LOCATION A)
81A 1 VERTICAL TURRET MILL, BRIDGEPORT SERIES 1, NEW 1988, 9" X 48" TABLE, 2 HP, 220/230/440/460/3/60, 5" QUILL TRAVEL, 28" TABLE TRAVEL, 12" SADDLE TRAVEL, R8 SPDL., CHROME KNEE, PWR. TABLE FEED, S/N 272385 (LOCATION B)
82 1 VERTICAL TURRET MILL, BRIDGEPORT SERIES 1, 9" X 48" TABLE, 2 HP, 220/230/440/460/3/60, 5" QUILL TRAVEL, 28" TABLE TRAVEL, 12" SADDLE TRAVEL, R8 SPDL., CHROME KNEE, PWR. TABLE FEED, SONY 2-AXIS D.R.O., S/N 218885 (LOCATION B)
83 1 VERTICAL TURRET MILL, BRIDGEPORT SERIES 1, 9" X 42" TABLE, (8) SPDS: 80-2720 RPM, R8 SPDL. TAPER, 1 HP MOTOR, 220/440/3/60, PWR. TABLE FEED, S/N J218161 (LOCATION B)
84 1 VERTICAL TURRET MILL, BRIDGEPORT SERIES 1, 9" X 42" TABLE, (8) SPDS: 80-2720 RPM, R8 SPDL. TAPER, 1 HP MOTOR, 220/440/3/60, PWR. TABLE FEED, D.R.O., S/N J169654 (LOCATION B)
85 1 CNC LATHE, MIGHTY MDL. VIPER VT-15, FANUC OTD CNC CONTROL, 15.75" SW. OVER BED, 9.45" SW. OVER CROSSLIDE, 13.78" DIST. BTN. CENTERS, 6.30" X-AXIS TRAVEL, 13.78" Z-AXIS TRAVEL, 6,000 RPM SPDL. SPDS., A2-5 SPDL. NOSE, 2.05" SPDL. HOLE, 1.81" THROUGH BAR CAP., 10 TOOL STATIONS, TAILSTOCK, CHIP CONVEYOR, S/N 3300100105 (LOCATION A)
86 1 HORIZONTAL BORING MILL, SACEM HERCULES, 3-1/2" TABLE TYPE, 51" X 43-1/4" BUILT-IN ROTARY TABLE, 19-1/2" BUILT-IN FACING HEAD, SPDL. SPDS: 7-1000 RPM, FACING HEAD SPDS: 7-180 RPM, APPROX. 40" CROSS TRAVEL, APPROX. 40" VERT. TRAVEL, S/N N.A. (LOCATION A)
87 1 CNC KEYSEATER, FROMAG MDL. RA CNC 100/750, FROMAG CNC CONTROL, 19.68" X 30.31" TABLE, 12.0" HT. TABLE, 0.118" TO 3.93" MAX. KEYWAY WIDTH, 29.52" MAX. KEYWAY LENGTH, 0.393" TO 19.68" BORE DIA., 77 LBS. MAX. WORKPIECE WEIGHT, 15 HP MOTOR, S/N 46701 ASK3348-4 (LOCATION A)
88 1 HYDRAULIC KEYSEATER, STUHLMAN MDL. POLY-50, 2" MAX. KEYWAY, 22" MAX. STROKE, VARIABLE HYD. STROKES: 0-12 SPM, 7.3 HP, HYD. MOTOR, 480/3/60, 25" DIA. INDEX TABLE, -120 DIVISIONS, 1" KEYWAY CUTTER, FLUSH FLOOR OPERATION (LOCATION B)
89 1 HORIZONTAL MILL, CINCINNATI NO. 3 MDL. 310-12 DIAL TYPE, 12" X 65" TABLE, SPDS: 18-1800 RPM, #50 TAPER, 18" VERT., 32" CROSS, 12" SADDLE, 10 HP, 220/440/3/60, ARBORS & SUPPORTS (MISSING ELECTRICAL PANEL) (LOCATION B)
90 1 HORIZONTAL PRODUCTION MILL, KENT OWENS, HAND OPERATED, #40 SPDL. TAPER, 9" HORIZ. TRAVEL, 9" X 25" T-SLOTTED TABLE, 8" MAX. TABLE TO SPDL. CENTER, 1 HP MOTOR, 208/220/440 (LOCATION B)
91 1 RAM TYPE HORIZONTAL MILL, HARDINGE MDL. TM-UM, 6-1/2" X 25" TABLE, SPDS: 110-1850 RPM, 8-1/2" LONG. TRAVEL, 13-1/4" VERT. TABLE TRAVEL, 3/4 HP MOTOR, 220/440/3/60, VARI. POWER FEED TABLE, FEED MOTOR, ARBORS & SUPPORTS (LOCATION B)
92 1 PANTOGRAPH, DECKEL MDL. L G1-L, 8" X 20" T-SLOTTED TABLE, 5" SADDLE TRAVEL, 5" VERT. TABLE TRAVEL (LOCATION B)
93 1 THREAD MILLER, LEES BRADNER 12" X 102" MDL. LT12X102, 102" DIST. BTN. CENTERS, 24" SW. OVER BED, 12" SW. OVER CARRIAGE CUTTER, 3 HP MILL HEAD MOTOR, 3 HP HEADSTOCK MOTOR, MILLING HEAD, TAILSTOCK, 15" DIA. 3-JAW CHUCK, FOLLOWREST, S/N HT-652 (LOCATION A)
94 1 THREAD MILLER, LEES BRADNER 12" X 102" MDL. LT12X102, 102" DIST. BTN. CENTERS, 24" SW. OVER BED, 12" SW. OVER CARRIAGE CUTTER, 3 HP MILL HEAD MOTOR, 3 HP HEADSTOCK MOTOR, MILLING HEAD, TAILSTOCK, 15" DIA. 3-JAW CHUCK, FOLLOWREST, S/N HT-1434 (LOCATION A)
95 1 THREAD MILLER, LEES BRADNER 24" X 54" MDL. HT 12x54, 54" DIST. BTN. CENTERS, 24" SW. OVER BED, 12" SW. OVER CUTTER CARRIAGE, 3 HP MILL HEAD MOTOR, 3 HP HEADSTOCK MOTOR, MILLING HEAD, TAILSTOCK, 15" DIA. 3-JAW CHUCK, FOLLOWREST, S/N HT-604 (LOCATION A)
96 1 THREAD MILLER, LEES BRADNER 8" X 36" MDL. LT 8x36, 36" DIST. BTN. CENTERS, 18" SW. OVER BED, 8" SW. OVER CUTTER CARRIAGE, 2 HP MILL HEAD MOTOR, 2 HP HEADSTOCK MOTOR, MILLING HEAD, TAILSTOCK, 12" DIA. 3-JAW CHUCK, FOLLOWREST, S/N LT-220 (LOCATION A)
97 1 PRODUCTION MILL, CINCINNATI HYPOWERMATIC SIMPLEX MDL. 300-186, NEW 1967, 18" X 104" TABLE, 72" TABLE TRAVEL, (16) SPDL. SPDS: 50-2000 RPM, 20 HP SPDL. MOTOR, S/N 6B4P5T-1 (LOCATION A)
98 1 PRODUCTION MILL, CINCINNATI MILACRON MDL. 100 POWERMATIC SIMPLEX, 12" X 48" TABLE, 24" TABLE TRAVEL, #50 NST SPDL. TAPER, (16) SPDL. SPDS: 40-1600 RPM, 7.5 HP DRIVE MOTOR, 3 HP FEED MOTOR, AUTO. CYCLE SELECTOR & CONTROLS, (2) ARBORS, ARBOR SUPPT., S/N 11B1P1AHE-66 (LOCATION A)
99 1 PRODUCTION MILL, K&T RISE & FALL MDL. 1224, 24" TABLE TRAVEL, TABLE FDS: 2.96-40 IPM, HEAD FDS: .3-18 IPM, SPDS: 50-1500 RPM, #40 SPDL. TAPER, 3" QUILL ADJ., 5 HP MOTOR, 3 HEADED INDEXER INCLUDED, SPDL. REVERSE, AUTO. CYCLE, ARBOR SUPPT. (LOCATION B)
100 1 HYDRAULIC VERTICAL BROACH, LAPOINTE MDL. VU-1, 36" STROKE, 20 HP MOTOR, 220 v., COOLANT SYSTEM, 451 HRS. ON METER, S/N 53043 (LOCATION B)
101 1 HEAVY DUTY SHAPER, CINCINNATI MDL. 24, 0 TO 24" STROKE, 9-119 SPM, FDS: .010-.170 IPS, 7" TRAVEL OF CLAPPER HEAD, 10 HP MOTOR, 230/460/3/60, 17.5"W. X 15" OPENING X 3.5" JAW HEIGHT SWIVEL VISE, 16" X 24" X 17" HT., T-SLOTTED TABLE (LOCATION B)
102 1 HIGH COLUMN RADIAL DRILL, CARLTON 4' X 13", 3A HEAD, SPDL. SPDS: 12-1200 RPM, #5 MT SPDL., 18" SPDL. TRAVEL, PWR. CLAMPING OF HEAD, COLUMN & ARM, RAPID TRAVERSE TO HEAD, 11 HP, 208/220/440/3/60, 24" X 30" TILTING BOX TABLE (LOCATION B)
103 1 BOX COLUMN DRILL, ALLEN MDL. MAVDW, NEW 4/1990, 22" X 26.5" TABLE, 1-1/2" DRILL CAP., #4 MT SPDL., VARIABLE SPDS: 60-375 RPM/250-1500 RPM, 15" VERT. TABLE TRAVEL, 16" VERT. HEAD TRAVEL, 3 HP, 230/460/3/60 (LOCATION B)
104 1 BOX COLUMN DRILL, ALLEN MDL. MAYOW, NEW 11/1990, 22" X 26.5" TABLE, 1-1/2" DRILL CAP., #3 MT SPDL. TAPER, 15" VERT. TABLE TRAVEL, 16" VERT. HEAD TRAVEL, SPDL. SPDS: 60-1500 RPM, 3 HP, 230/460/3/60 (LOCATION B)
105 1 BOX COLUMN DRILL, ALLEN, NEW 1986, 21" X 24" TABLE, #4 MT SPDL. TAPER, 17" VERT. TABLE TRAVEL, 17" VERT. HEAD TRAVEL, VARIABLE SPDL. SPDS: 50-1800 RPM, 5 HP, 230/460/3/60 (LOCATION B)
106 1 JIB BORER, SIP MDL. HYDROPTIC 7, 40.4" X 61.5" TABLE, 55" TABLE TRAVEL, 40" HEAD CROSS TRAVEL, 39-3/8" MAX. DIST. SPDL. TO TABLE, 12" QUILL TRAVEL, 63" DIST. BTN. UPRIGHTS, 4,500 WORK LOAD CAP., SPDL. SPDS: 40-2000 RPM, SPDL. FDS: .016-.040 IPR, TABLE FDS: 0-20 IPM, SIP 31" OPTICAL DIVIDING TABLE, SIP 17-3/4" TILTING ROTARY TABLE, SIP BORING HEADS, SIP OPTICAL DEVICES, SIP TOOLHOLDERS, SIP MANUALS, D.R.O. (LOCATION B)
107 1 HYDRAULIC SURFACE GRINDER, MATTISON 42" X 144" RECIPROCATING TYPE HORIZONTAL SPINDLE, (3) 42" X 48" MAGNETIC CHUCKS, 20" X 6" MAX. WHEEL CAP., APPROX. 42" MAX. HEIGHT UNDER WHEEL, RECENTLY REBUILT (LOCATION A)
108 1 HYDRAULIC SURFACE GRINDER, GALLMEYER & LIVINGSTON 12" X 48" MDL. 65, 12" X 48" CHUCK, NEUTROFIER CONTROL, 50" LONG. TRAVEL, 14" CROSS TRAVEL, 14" VERT. HEIGHT, GRINDING WHEEL SPDS: 1925-2500 RPM, GRINDING WHEEL DIA.: 11" HIGH/12" LOW SPD., 5 HP MAIN MOTOR, 220/440 v., VERT. RAPID TRAVERSE (LOCATION B)
109 1 HYDRAULIC SURFACE GRINDER, GALLMEYER & LIVINGSTON 12" X 24" MDL. 45, 12" WHEEL SIZE, 16" MAX. UNDER WHEEL, MANUAL DOWNFEED, NEUTROFIER MAGNETIC CONTROL, 440 v., COOLANT TANK & PUMP, BIJUR LUBRICATION SYSTEM, REBUILT w/40 HRS. USE (LOCATION B)
110 1 HYDRAULIC SURFACE GRINDER, THOMPSON 8" X 24", 10" X 1" WHEEL SIZE, 10" MAX. PART HEIGHT, 3 HP SPDL. MOTOR, NEUTROFIER MAGNETIC CHUCK CONTROLLER, 1.5 HP MOTOR/PUMP, COOLANT PUMP (LOCATION B)
111 1 PRECISION VERTICAL GRINDER, CAMPBELL MDL. ER6680-24S, NEW 12/1987, 66" DIA. WORK TABLE (8 T SLOTS), 80" MAX. SWING, 15 HP VARIABLE SPD. SCR WORKTABLE DRIVE, VARIABLE WORKTABLE SPDS: 1-60 RPM, 12" MIN./48" MAX. UNDER RAIL, 50" X-AXIS SADDLE TRAVEL, 24" Z-AXIS SPDL. TRAVEL, 15 HP SPDL. MOTOR, ELEVATING CROSS RAIL, SOLID STATE MICRO-PROCESSOR CONTROL STATION, DRAWINGS, SCHEMATICS, MANUAL, S/N 696.86 (CURRENTLY DISASSEMBLED) (LOCATION B)
112 1 UNIVERSAL CYLINDRICAL GRINDER, PROFITMASTER 12" X 60", (2) INTERNAL SWING-DOWN GRINDING ATTACHS., (3) SPARE INTERNAL GRINDING SPDLS., RADIUS DRESSING ATTACH., (2) 2 PT. STEADYRESTS, 6" DIA. 3-JAW CHUCK, WHEEL BALANCING STAND w/ARBOR, (2) SPARE WHEEL COLLETS, ASSORTED DRIVING DOGS, 12" FACEPLATE, 14" X 2" WHEEL SIZE, 4 KW WHEEL DRIVE MOTOR, ASSORTED NEW WHEELS IN BOXES, S/N 1917 (LOCATION A)
113 1 UNIVERSAL CYLINDRICAL GRINDER, TSCHUDIN 8" X 14", MDL. HT G400, DRESSING ATTACH., 2 PT. STEADYREST, 6" DIA. 4-JAW CHUCK, S/N 63646 (LOCATION A)
115 1 PLAIN HYDRAULIC CYLINDRICAL GRINDER, OVERBECK 10" X 24" MDL. 600R, 10.8" SW. OVER TABLE, 7.08" MAX. GRINDING DIA., 24.8" MAX. GRINDING LENGTH, WORKHEAD SPDS: 50-450 RPM, 18" X 3" X 8" WHEEL DIMS., 6 DEG. WORKHEAD SWIVEL, 1.37" DIA. WORKHEAD THROUGH HOLE, FORM DRESSING ATTACH., AUTO. CYCLE, HEIDENHAIN 2-AXIS D.R.O. (LOCATION B)
116 1 PLAIN HYDRAULIC CYLINDRICAL GRINDER, LANDIS 6" X 18" MDL. 1R, PLUNGE INFEED, S/N 883-77 (FOR PARTS USE) (LOCATION B)
117 1 HYDRAULIC ROTARY SURFACE GRINDER, CENTRO METALCUT MDL. H-24, NEW 12/1984, 24" DIA. MAG. CHUCK, 3/4" CHUCK LIFT, 34" MAX. SWING IN WATER PAN, 10" MAX. WORK HEIGHT, 16" WHEEL SIZE, 17" WHEEL STROKE, 12" VERT. KNEE TRAVEL, 10 DEG. ANGULAR TILT CONVEX & CONCAVE, 1,400 WHEELHEAD SPDL. SPD., TBL. SPDS: 37-155 RPM, 20 HP, 230/460/3/60, HYD. UNIT, COOLANT SYSTEM (LOCATION B)
118 1 DRILL GRINDER, SELLERS MDL. 6G, 5/16" DIA. TO 3" DIA. CAP., 8" DIA. GRINDING WHEEL, 60 DEG. TO 160 DEG. SWIVEL ADJ., 2 HP, 220/440/3/60 (LOCATION B)
119 1 DRILL GRINDER, CINCINNATI SPIROPOINT, 5/8" CAP., 1/2 HP SGL. PHASE, BIJUR SPRAY MIST, STRAIGHT & OSCILLATION FLUTE GRINDING (LOCATION B)
120 1 DRILL GRINDER, OLIVER MDL. 21, 3/32" TO 1/2" CAP., 1 HP, 115/1 PH (LOCATION B)
120A 1 TOOL & CUTTER GRINDER, CINCINNATI, S/N 1D2T1J-482 (LOCATION A)
121 1 AUTOMATIC HYDRAULIC HORIZONTAL BANDSAW, W.F. WELLS MDL. OJ-24-A756, 36"W. X 24" HT. MAX. CUTTING CAP., VERT. CLAMPING, DUAL COLUMN, 32" WHEELS, 1-1/4" BLADE SIZE, COOLANT SYSTEM (LOCATION B)
122 1 AUTOMATIC HORIZONTAL BANDSAW, DOALL MDL. C-1213A, NEW 1986, 12" X 13" RATED CAPACITY, VARIABLE SPD: 60-350 FPM, 144" X 1-3/8" BLADE SIZE, 0" TO 24" INDEXING, COOLANT, HYD. DOWNFEED, 5 HP, 460 v., 3 PHASE, S/N 412-86312 (LOCATION B)
123 1 HORIZONTAL BANDSAW, DOALL MDL. C-916, 9" X 16" CAP., 159" BAND LENGTH, 2 HP MOTOR, 230/460/3, GRAVITY FEED - VARIABLE, MANUAL CLAMPING, 37" TABLE EXTENSION, VARIABLE SPD. BLADE (LOCATION B)
124 1 SEMI-AUTOMATIC HORIZONTAL BANDSAW, KYSOR JOHNSON MDL. H-250-SAM 10" RD. CAP., 14" FLAT CAP., HYD. VISE, VARIABLE SPD., VARIABLE FDS: 88-262 FPM, 138"L. BLADE, 1"W. BLADE, 3 HP MOTOR, 230/460/3/60 (LOCATION B)
124A 1 HIGH SPEED VERTICAL BANDSAW, DOALL MDL. 3620 ZW, 30" X 36" TABLE, 19" X 19" SECONDARY TABLE, BLADE SPDS: 40-9000 FPM, 5 HP MOTOR, 480 v., FPM GAUGE, BLADE WELDER & GRINDER (LOCATION B)
124B 1 VERTICAL BANDSAW, DOALL MDL. 2612-1H, 177" BAND LENGTH, VARIABLE SPDS: 25-6000 RPM, 26" THROAT, 12" MAX. PART HEIGHT, 24" X 30-1/2" TILTING TABLE, 3 HP, 230/460/3/60, BLADE WELDER & GRINDER (LOCATION B)
124C 1 VERTICAL BANDSAW, CLAUSING STARTRITE MDL. V900F, NEW 1997, 26" X 28" WORKTABLE, 13" X 22" WORKTABLE, 36" THROAT, 14.5" MAX. PART HEIGHT, SPDS: 50-5200 RPM, 3 HP MOTOR, 230/440/3, SPEED/BLADE SELECTOR, BLADE WELDER & GRINDER (LOCATION B)
125 1 HYDRODYNAMIC BARFEEDER, MTA 12' MDL. MINI-SWISS 16, 3-16 mm DIA., 12'L. BARS (LOCATION A)
126 1 BARFEED, LNS TYPE THB65-3.7 (LOCATION B)126A 1 PNEUMATIC BARFEED, LIPE MDL. 225, w/FEED
TUBE (LOCATION B) 126B 1 PNEUMATIC BARFEED, LIPE MDL. 125 (LOCATION B)
127 1 GRINDING SPINDLE, RED HEAD, 3.5" DIA. X 4.5"L. SPDL. HSG, 15,500 MAX. RPM, S/N 110687 (74 SIZE HEALD) (LOCATION B)
127A 1 GRINDING SPINDLE, RED HEAD, 3.5" DIA. X 4.5"L. SPDL. HSG, 15,500 MAX. RPM, S/N 110686 (74 SIZE HEALD) (LOCATION B)
127B 1 GRINDING SPINDLE, RED HEAD, 3.5" DIA. X 4.5"L. SPDL. HSG, 15,500 MAX. RPM, S/N 110697 (74 SIZE HEALD) (LOCATION B)
127C 1 GRINDING SPINDLE, RED HEAD, 3.5" DIA. X 4.5"L. SPDL. HSG, 15,500 MAX. RPM, S/N 110696 (74 SIZE HEALD) (LOCATION B)
127D 1 GRINDING SPINDLE, RED HEAD, 3.5" DIA. X 4.5"L. SPDL. HSG, 15,500 MAX. RPM, S/N 110690 (74 SIZE HEALD) (LOCATION B)
127F 1 GRINDING SPINDLE, RED HEAD, 3.5" DIA. X 4.5"L. SPDL. HSG, 15,500 MAX. RPM, S/N 110692 (74 SIZE HEALD) (LOCATION B)
128 1 GRINDING SPINDLE, RED HEAD, 4.25" DIA. X 4.5"L. SPDL. HSG, 14,000 MAX. RPM, S/N 107065 (74 SIZE HEALD) (LOCATION B)
129 1 GRINDING SPINDLE, RED HEAD, 4.25" DIA. X 4.5"L. SPDL. HSG, 12,500 MAX. RPM, S/N 110674 (74 SIZE HEALD) (LOCATION B)
129A 1 GRINDING SPINDLE, RED HEAD, 4.25" DIA. X 4.5"L. SPDL. HSG, 12,500 MAX. RPM, S/N 110673 (74 SIZE HEALD) (LOCATION B)
129B 1 GRINDING SPINDLE, RED HEAD, 4.25" DIA. X 4.5"L. SPDL. HSG, 12,500 MAX. RPM, S/N 107077 (74 SIZE HEALD) (LOCATION B)
129C 1 GRINDING SPINDLE, RED HEAD, 4.25" DIA. X 4.5"L. SPDL. HSG, 12,500 MAX. RPM, S/N 110683 (74 SIZE HEALD) (LOCATION B)
129D 1 GRINDING SPINDLE, RED HEAD, 4.25" DIA. X 4.5"L. SPDL. HSG, 12,500 MAX. RPM, S/N 110684 (74 SIZE HEALD) (LOCATION B)
129F 1 GRINDING SPINDLE, RED HEAD, 4.25" DIA. X 4.5"L. SPDL. HSG, 12,500 MAX. RPM, S/N 110677 (74 SIZE HEALD) (LOCATION B)
130 1 GRINDING SPINDLE, RED HEAD, 5.5 DIA. X 4.5"L. SPDL HSG, 7,500 MAX. RPM, S/N 107019 (74 SIZE HEALD) (LOCATION B)
131 1 GRINDING SPINDLE, RED HEAD, 2.25" DIA. X 22"L. SPDL. HSG, 6,000 MAX. RPM, S/N 104968 (72 SIZE HEALD) (LOCATION B)
132 1 GRINDING SPINDLE, RED HEAD, 3.75" DIA. X 13"L. SPDL. HSG, 4,800 MAX. RPM, S/N 103940 (72 SIZE HEALD) (LOCATION B)
133 1 GRINDING SPINDLE, RED HEAD, MOTORIZED, 350 v., 1,000 Hz, 17.5 AMPS, 3 PHASE, 2 POLE, 6 kW, 60,000 RPM (72 SIZE HEALD) (LOCATION B)
134 LOT GRINDING SPINDLES: 4.5" DIA. X 3.5"L. SPDL. HSG, 11,000 MAX. RPM, S/N 68890 & 3.75" DIA. X 3.5"L. SPDL. HSG, 12,500 MAX. RPM, S/N 29487 (72 SIZE HEALD) (LOCATION B)
137 1 VERTICAL TURRET MILLING HEAD, BRIDGEPORT, 1 HP, 5" QUILL STROKE, R-8 TAPER (LOCATION B)
138 1 RIGHT ANGLE HEAD, KEARNEY & TRECKER NO. 5 (LOCATION B)
139 1 UNIVERSAL VERTICAL HEAD, CINCINNATI #3 (LOCATION B)
139A 1 UNIVERSAL VERTICAL MILLING HEAD, OKK (LOCATION B)
140 1 DEEP HOLE DRILL COOLANT PUMP & FILTER SYSTEM, (15) FINE MESH FILTERS, 3 HP, 220/440/3 PH, IR-PUMP, 3,460 RPM, HYD. TEST 100 (LOCATION B)
141 1 HEX TURRET ATTACHMENT (FOR ENGINE LATHE), 7-5/8" FLAT WAY TO TURRET HOLE, 5.8" CENTE TO CENTER OF WAYS, 1.5" DIA. (LOCATION B)
141A 1 LARGE ANGLE PLATE, 36" X 35" X 26" DP. (LOCATION B)
142 LOT ANGLE PLATES (LOCATION B)142A LOT ANGLE PLATES (LOCATION B)143 1 MACHINE VISE, 13" (LOCATION B)
143A 1 MACHINE VISE, 12" (LOCATION B)143B 1 MACHINE VISE, 12" (LOCATION B) 143C 1 MACHINE VISE, 9" (LOCATION B) 143D LOT SWIVEL BASES (FOR VISES), (APPROX. 4),
INCLUDING (1) TILTING UNIVERSAL TYPE (LOCATION A)
144 1 ROTARY TABLE, 18", w/GEAR DRIVE UNIT (LOCATION B)
144A 1 ROTARY TABLE, 16" (LOCATION B)144B 1 ROTARY TABLE, 14" (LOCATION B)144C 1 ROTARY TABLE, 12" (LOCATION B)145 LOT DRILLED & TAPPED SUB-PLATES (LOCATION B)
145A 1 MAGNETIC CHUCK, 8" X 24" (LOCATION B)145B 1 T-SLOTTED SUB-TABLE, 12" X 22" (LOCATION B)
145C 1 SUB-TABLE, 20-1/2" X 48-1/2" X 12" HT. (LOCATION B)
146 LOT SOFT JAWS (LOCATION B)146A LOT SOFT JAWS (APPEAR UNUSED) (LOCATION B)147 1 TURRET ATTACHMENT (FOR WARNER & SWASEY
5A), T-SLOT TOOL BASE w/DBL. CUTTER BLOCK FORE END GROOVING FROM HEX TURRET (LOCATION B)
148 1 RISER, FOR BRIDGEPORT 7" VERTICAL TURRET MILL) (LOCATION B)
148A 1 RISER, FOR BRIDGEPORT 4" VERTICAL TURRET MILL (LOCATION B)
148B 1 BORING BAR, DEVIBRATOR, 4" X 50"L. (LOCATION B)
148C 1 BORING BAR, WARNER & SWASEY 4A, 5" DIA. X 31"L., COOLANT THROUGH BAR (LOCATION B)
148D 1 BORING BAR, WARNER & SWASEY 4A, 5" DIA. X 31"L., COOLANT THROUGH BAR (LOCATION B)
148F LOT BORING BARS: 2.75" DIA. X 37"L. w/HOLDER & 2.25" X 33"L. (LOCATION B)
148G 1 BORING BAR, 4" SQ. X 36"L. (LOCATION B)148H 1 BORING BAR, 6" SQ. X 43"L., w/T-NUT (LOCATION B)
148I LOT BORING BARS (LOCATION B)148J LOT BORING BARS (LOCATION B)149 LOT BORING BAR TOOLHOLDERS (LOCATION B)
149A LOT BORING BAR TOOLHOLDERS (LOCATION B) 150 1 MACHINE COOLANT TANK, 48" X 37" X 14" DP.
(LOCATION B)150B LOT MACHINE COOLANT TANKS, 20" X 48" X 15" DP. &
12" X 20" X 10" DP. (LOCATION B)151 LOT GRINDING WHEELS, INCLUDING NORTON DIAMOND
WHEEL (LOCATION B)151A LOT GRINDING WHEEL HUBS (LOCATION B)151B LOT HONING STONES (LOCATION B)152 LOT WAX PAPER MATERIAL (FOR MACHINE PARTS
PROTECTION) (LOCATION B)153 LOT COOLANT PUMPS w/TANKS, 15" X 26" X 20" DP. &
12" X 20" X 10" DP. (LOCATION B)154 LOT COOLANT PUMPS w/TANKS, 16" X 20" X 15" DP. &
16" X 22" X 19" DP. (LOCATION B)155 LOT CARBIDE SAW BLADES, 24" DIA., APPROX. (7)
(APPEARS UNUSED) (LOCATION A)156 1 SINE PLATE, 20" X 16", ADJUSTABLE (LOCATION A)
157 1 SINE PLATE, 16" X 24", ADJUSTABLE (LOCATION A)
158 1 COMPOUND SINE PLATE, 8" X 12" (LOCATION A)
159 1 COMPOUND SINE PLATE, 8" X 12" (LOCATION A)
160 1 COMPOUND SINE PLATE, 8" X 12" (LOCATION A)
161 1 SINE PLATE, 6" X 12" (LOCATION A)
162 1 T-SLOTTED ANGLE PLATE, 18" X 10" (LOCATION A)
162A LOT T-SLOT & UNSLOTTED TABLES (LOCATION A)163 1 ROTARY INDEXER, 6" DIA. 4-JAW CHUCK (LOCATION
A) 164 LOT WIRE WHEELS, SANDING BELTS & PROTECTIVE
EYEWEAR (LOCATION A)165 1 MACHINIST'S LEVEL, STARRETT (LOCATION A)
165A 1 MACHINIST'S LEVEL, STARRETT (LOCATION A) 165B 1 MACHINIST'S LEVEL, STARRETT (LOCATION A) 166 1 COOLANT FILTRATION SYSTEM, ENCYCLON MDL.
653-150-01-DT, 5 HP GUSHER PUMP, 230/460/3 PHASE, S/N 8028-77 (LOCATION B)
166A LOT MANCHESTER TOOLING (LOCATION B)167 LOT BROACH TOOLING (LOCATION B)168 LOT TIE DOWN TOOLING (LOCATION B)
168A LOT TIE DOWN TOOLING (LOCATION B)169 LOT SHAPER & SLOTTER TOOLING (LOCATION B)170 LOT ENGINE LATHE ROCKER TYPE TOOLING (LOCATION
B)171 LOT TAPS (LOCATION B) 172 LOT ASSORTED BEARINGS (LOCATION B)173 LOT CARBIDE INSERT TOOLHOLDERS (LOCATION B)174 LOT CARBIDE INSERTS, CARBOLOY TNMG 543E gr 370
(APPROX. 420 PCS.) (UNUSED) (LOCATION B)
174A LOT CARBIDE INSERTS (LOCATION B)175 LOT BRAZED CARBIDE CUTTING TOOLS (LOCATION B)
176 LOT HIGH SPEED STEEL CUTTING TOOLS & SOME BRAZED TOOLS (LOCATION B)
177 LOT GEAR HOBS (LOCATION B)178 LOT DRILL BITS (APPROX. 5 BOXES) (LOCATION B) 179 1 PARALLEL BAR, 6' (LOCATION A)
179A 1 PARALLEL BAR, 4' (LOCATION A) 179B 1 PARALLEL BAR, 3' (LOCATION A)179C 1 LASER ALLIGNMENT SYSTEM, COMBI-LASER
(LOCATION A)180 LOT LAPPING PLATES, 18" DIA. (LOCATION B)
180A LOT GRINDING FIXTURE, HARIG AIR FLOW FIXTURE FOR END MILLS, S/N E023064 (LOCATION B)
181 LOT GRINDING MACHINE ACCESSORIES (LOCATION B)
181A LOT GRINDING MACHINE ACCESSORIES (LOCATION B)
181B LOT GRINDING MACHINE ACCESSORIES (LOCATION B)
181C LOT GRINDING MACHINE ACCESSORIES (LOCATION B)
181D LOT GRINDING MACHINE ACCESSORIES (LOCATION B)
182 LOT MILLING MACHINE ACCESSORIES (LOCATION B)
182A LOT MILLING MACHINE ACCESSORIES (LOCATION B)
182B LOT MILLING MACHINE ACCESSORIES (LOCATION B)
183 LOT J&L LATHE TOOLING & ATTACHMENTS, INCLUDING COLLET PADS (LOCATION B)
184 LOT MILLING & ENGINE LATHE TOOLING (LOCATION B)
185 LOT MORI SEIKI TOOLHOLDERS, w/SHOP CART (LOCATION B)
186 LOT DEAD CENTERS (LOCATION B)187 LOT RUBBER DRIVE BELTS (LOCATION B)188 LOT RAW MATERIAL: NYLON (LOCATION B)189 LOT BULLARD CUTMASTER PARTS: MOTOR MOUNT,
COOLANT PUMP, PENTAGON TURRET, COOLANT GUARD, ETC. (LOCATION B)
189A LOT CABINETS, w/MISC. MACHINE TOOLING (LOCATION B)
200 1 LARGE CAPACITY MOBILE CRANE, MOBILIFT MDL. MBL075 75 TON CAP., NEW 2008, 18' 3-SECTION BOOM EXTENDS TO 44'-8", CARL CONTROL SYSTEM, LSI ANTI-2-BLOCK, TELESCOPING COUNTERWEIGHT, CUMMINS DIESEL ENGINE, JOYSTICK STEERING & DRIVE, 10' POWER BOOM, 10' MANUAL BOOM, 75 TON CAP. MAIN BOOM & POWER BOOM PICKING EYES, 50 TON HOOK BLOCK, 90 DEG. STEERING, COUNTERWEIGHTS A, B & C, S/N MBL075045 (LOCATION A)
201 1 LARGE CAPACITY RIGGING FORKLIFT, BRISTOL MDL. 80/100 100,000 LB. CAP. RIGGER'S SPECIAL, NEW 2008, 106" MAST IN DOWN POS., 98" MAX. LIFT HEIGHT, LPG FUEL, LARGE MONO-MATIC PNEU. STYLE CUSHION TIRES, 8' FORKS, INCLUDES LARGE & SMALL TELESCOPING RIGGING BOOMS (LARGE BOOM IS 4' HIGHER THAN STANDARD, DESIGNED FOR DOING PRESS MACHINE REMOVALS), UNIT #112517, S/N S-40-10831 (LOCATION A)
202 1 LARGE CAPACITY FORKLIFT, TAYLOR 30,000 LB. CAP., MDL. Y30WOM, 453 DETROIT DIESEL, 30,000 LB. @ 24" LOAD CENTER, 13' LIFT, 146" LOWERED HEIGHT, 1200 X 20 TIRES, AUTO. TRANS., 1,575 HRS. ON METER, 92" FORKS, S/N 11857 (LOCATION A)
203 1 LARGE CAPACITY FORKLIFT, HYSTER 30,000 LB. CAP., MDL. H300B, DIESEL ENGINE, MONOTROL TRANS., 2-STAGE MAST, 96"W. FORK CARRIAGE, 96" FORKS, 210" MAX. LIFT, AIR BRAKES, DUAL FRONT PNEU. TIRES, RECENTLY RECONDITIONED, 2,470 H.O.M. SINCE REBUILT, S/N B19P-1914C (LOCATION A)
204 1 LARGE CAPACITY FORKLIFT, TAYLOR 25,000 LB. CAP., MDL. TY25OM, 453 DETROIT DIESEL, 25,000 LB. @ 24" LOAD CENTER BASIC CAPACITY, 15' LIFT, 151" LOWERED HEIGHT, SOLID PNEU. DRIVE TIRES 1200 X 20, AIR 1200 x 20 STEER TIRES, SIDE SHIFT, AUTO. TRANS., PWR. SHIFT TRANS., 3,295 HRS. ON METER, 94" FORKS, S/N 17087
205 1 LARGE CAPACITY FORKLIFT, TAYLOR 22,000 LB. CAP., MDL. Y22WO, 453 DETROIT DIESEL, 22,000 LB. @ 24" LOAD CENTER, 18' LIFT, 170" LOWERED HEIGHT, SIDE SHIFT, PWR. SHIFT TRANS., 2,280 HRS. ON METER, 93" FORKS, S/N 12400 (LOCATION A)
206 1 FORKLIFT, LINDE 18,000 CAP. MDL. H80D, NEW 2003, DEUTZ 6 CYL. DIESEL ENGINE, 150 STANDARD MAST SS, PNEU. TIRES, S/N E1X35R00857 (LOCATION A)
207 1 FORKLIFT, HYSTER 15,500 LB. CAP., MDL. S155XL, NEW 2007, DIESEL ENGINE, 116" STANDARD MAST, 153" LIFT HEIGHT, CUSHION TIRES, FORK POSITIONER, 48" FORKS, S/N C024V02982E (LOCATION A)
208 1 FORKLIFT, HYSTER 15,000 LB. CAP., LPG ENGINE, 68" FORKS, 2-STAGE MAST, CUSHION TIRES, 98" HT. MAST (LOCATION A)
209 1 FORKLIFT, HYSTER 15,000 LB. CAP. MDL. H150-CMIL, CONTINENTAL MDL. FS-244 GASOLINE ENGINE, PNEU. TIRES, 4' FORKS (LOCATION B)
210 1 FORKLIFT, HYSTER 12,000 LB. CAP., MDL. S120FTPRS, NEW 2007, LPG, 83" TRIPLE STAGE MAST, 163" LIFT HEIGHT, CUSHION TIRES, VALVED FOR SIDE SHIFT, 42" FORKS, S/N G004V02307E (LOCATION A)
211 1 FORKLIFT, HYSTER 12,000 LB. CAP., MDL. S120XMS, NEW 2004, LPG, 89" TRIPLE STAGE MAST, 185" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, 42" FORKS, S/N F004V02138B (LOCATION A)
212 1 FORKLIFT, YALE 10,000 LB. CAP., MDL. GLC 100VXNGSE092, NEW 2008, LPG, 92" TRIPLE STAGE MAST, 185" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, 42" FORKS, S/N E818V02676F (LOCATION A)
213 1 FORKLIFT, CATERPILLAR 10,000 LB. CAP., MDL. TC100D, LPG, 100" STANDARD MAST, 168" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, FORK POSITIONER, 42" FORKS, S/N 5KB03006 (LOCATION A)
214 1 FORKLIFT, TOYOTA 8,000 LB. CAP., MDL. 7FGCU35BCS, NEW 2004, LPG, 104" TRIPLE STAGE MAST, 238" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, 42" FORKS, S/N 62511 (LOCATION A)
215 1 FORKLIFT, TOYOTA 8,000 LB. CAP., MDL. 7FGCU35BCS, NEW 2004, LPG, 104" TRIPLE STAGE MAST, 238" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, 42" FORKS, S/N 62515 (LOCATION A)
216 1 FORKLIFT, KOMATSU 8,000 LB. CAP., MDL. FG35ST-6, LPG, 87" 2-STAGE MAST, 130" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, 42" FORKS, S/N 061374A (LOCATION A)
217 1 FORKLIFT, HYSTER 7,000 LB. CAP., MDL. S70FT, NEW 2006, LPG, 89" TRIPLE STAGE MAST, 187" LIFT HEIGHT, CUSHION TIRES, VALVED FOR SIDE SHIFT, 42" FORKS, S/N F187V5284D (LOCATION A)
218 1 FORKLIFT, YALE 6,500 LB. CAP., MDL. GLC065TGNUAQ082, NEW 2001, LPG, 82" QUAD MAST, 240" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, 42" FORKS, S/N E187V15724Y (LOCATION A)
219 1 FORKLIFT, CATERPILLAR 6,000 LB. CAP., MDL. GC30K, NEW 2005, LPG, 88" QUAD MAST, 258" LIFT HEIGHT, CUSHION TIRES, SIDE-SHIFT, 42" FORKS, S/N AT83D01472 (LOCATION A)
219A 1 FORKLIFT, YALE 6,000 LB. CAP., MDL. GLC060TGNUAE084, LPG, 187" MAX. LIFT HEIGHT, CUSHION TIRES, 3" 3-STAGE MAST, 4' FORKS, SIDE SHIFTER (LOCATION A)
220 1 FORKLIFT, HYSTER 5,000 LB. CAP., MDL. S50FT, NEW 2010, LPG, 83" TRIPLE STAGE MAST, 189" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, 42" FORKS, S/N F187V15934H (LOCATION A)
221 1 FORKLIFT, HYSTER 5,000 LB. CAP., MDL. S50FT, NEW 2010, LPG, 83" TRIPLE STAGE MAST, 189" LIFT HEIGHT, CUSHION TIRES, SIDE SHIFT, 42" FORKS, S/N F187V15937H (LOCATION A)
221A 1 FORKLIFT, YALE 5,000 LB. CAP., MDL. GLC050DENUAE, 190" MAX. LIFT HEIGHT, LPG, CUSHION TIRE, 80" 3-STAGE MAST, 5' FORKS, S/N A823N02161T (LOCATION A)
222 1 ELECTRIC FORKLIFT, TCM 3,000 LB. CAP., MDL. FCB20E3, 189" MAX. LIFT HEIGHT, 42"L. FORKS, 8" TO 36" FORK SPACING, 3-STAGE MAST, 36 v. SYSTEM, SIDE SHIFT, BATTERY CHARGER, S/N A721f00493 (LOCATION A)
223 1 ELECTRIC FORKLIFT, WESCO 1,000 LB. CAP., MDL. PCBEL-64-25, BUILT-IN CHARGER, 24"L. FORKS, S/N 167742 (LOCATION A)
224 LOT FORKLIFT FORKS, 48"L. (LOCATION B)225 1 FORKLIFT MANLIFT PLATFORM (LOCATION B)226 LOT FORKLIFT EXTENSIONS, 6' (LOCATION A)227 LOT FORKLIFT EXTENSIONS, 6' (LOCATION A)228 1 FORKLIFT BOOM, HERCULES MDL. B1-646, 2 T. CAP.
(LOCATION A)229 1 REMOVABLE GOOSENECK TRAILER, FONTAINE 55 T.
CAP. MDL. MAGNATUDE 55H 60, NEW 2008, 110,000 LB./49,898 KG FRAME RATING, TRIPLE AXLE, DUAL WHEEL, AIR RIDE, AIR WEIGH SCALES, 26' WELL, CHECK PLATE REINFORCED FLOOR, HYD. SELF-CONTAINED, GASOLINE PWRD. MOTOR MTD. ON TRAILER NECK, 275/7OR 22.5 TIRES, TX LICENSE NO. X44932, VIN 13NE5230893549516 (LOCATION A)
230 1 UTILITY TRUCK, 2011 FORD MDL. F350 "SUPER DUTY" CREW CAB, 6,033 LB. G.V.W.R., B20 6.7 PWR. STROKE, AM/FV/CD, AIR COND., PWR. WINDOWS, LOCKS & MIRRORS, LEATHER INTERIOR, KNAPHEIDE UTILITY TRUCK BODY w/OVERHEAD STORAGE RACK, ASSEMBLED BY GENERAL TRUCK & BODY MFG., ODO: 50,769 MILES, VIN 1FD8W3GT6BE03494 (LOCATION A)
231 1 UTILITY TRUCK, 2011 FORD MDL. F250 "SUPER DUTY" EXTENDED CAB, GASOLINE ENGINE, LEATHER SEATS, PWR. WINDOWS, LOCKS & MIRRORS, AM/FM/CD, AIR COND., KNAPHEIDE UTILITY TRUCK BODY w/SLIDING BED COVER, ASSEMBLED BY GENERAL TRUCK & BODY MFG., ODO: 62,203 MILES, VIN 1FT7X2A61BEB87375 (LOCATION A)
232 1 VAN TYPE TOOL TRAILER, LUFKIN 53', 55,000 LB. G.V.W.R., VIN 1L01A5320T1119582 (LOCATION A)
235 1 HYDRAULIC JACKING SYSTEM, ENERPAC 200 T. CAP., 10,000 PSI, 700 BAR SYSTEM, MULTIPLE VALVES & HOSING (LOCATION A)
236 LOT MACHINERY MOVING SKATES, UP TO 50 T. CAP. (LOCATION A)
238 LOT MACHINE SKATES & CHAIN STRAP (LOCATION B)
239 1 MACHINE ALIGNMENT ACCESSORY: CYLINDRICAL SQUARE (LOCATION A)
240 1 PORTABLE GENERATOR, DIESEL PWRD., 15 KW, 516 HRS., SKID MTD. (LOCATION A)
241 1 JOBSITE TOOLBOX, JOBOX (LOCATION A)241A 1 TOOLBOX BOX (LOCATION A)241B 1 TOOLBOX BOX (LOCATION A)241C 1 TOOLBOX, KNAACK (LOCATION A) 241D 1 TOOLBOX (LOCATION A) 242 LOT LIFTING CHAINS (LOCATION A)243 1 SAFE JACK, ROL-A-LIFT (LOCATION A)244 1 SAFE JACK, ROL-A-LIFT (LOCATION A)245 1 SPREADER BAR, HARRINGTON 3 T. CAP. (LOCATION
A)245A 1 SPREADER BAR, ESSETIERRE 11,000 kG MAX. CAP.,
NEW 2002 (LOCATION A)246 1 ELECTRIC CHAIN HOIST, BUDGIT 2 T. CAP.,
w/PENDANT CONTROL & TROLLEY (LOCATION A)
246A 1 ELECTRIC CHAIN HOIST, DAYTON 2 T. CAP., w/PENDANT CONTROL & TROLLEY (LOCATION A)
246B 1 ELECTRIC CHAIN HOIST, COFFING 1 T. CAP., w/PENDANT CONTROL & TROLLEY (LOCATION A)
247 1 ELECTRIC CHAIN HOIST, DAYTON 1/2 T. CAP., w/PENDANT & TROLLEY (LOCATION A)
247B 1 ELECTRIC CHAIN HOIST, LOADSTAR 1 T. CAP., w/PENDANT CONTROL & TROLLEY (LOCATION A)
249 LOT 3 T. CAP. CHAIN HOIST & TURNBUCKELS w/WIRE ROPE & HOOKS (LOCATION B)
250 1 MANIPULATOR ARM WITH REACH-IN CAPABILITY, CM LODEARM 3030, w/PEDESTAL & BUTTON VARIABLE CONTROL HOOK, S/N 3030-0934 (LOCATION A)
251 1 CABLE PULLER, GB ENERPAC MDL. C-1000, w/ATTACHMENTS (LOCATION A)
252 1 3 T. CAP. LEVER HOIST, COFFING/DUFF LYNX MDL. LSB-6000, 5' LIFT (LOCATION A)
253 1 3 T. CAP. LEVER HOIST, COFFING MDL. MA30-2 (LOCATION A)
254 1 2 T. CAP. LEVER HOIST, COFFING/DUFF LYNX MDL. LLC-4000, 5' LIFT (LOCATION A)
254A 1 2 T. CAP. LEVER HOIST, COFFING/DUFF LYNX MDL. LLC-4000, 5' LIFT (LOCATION A)
255 1 1-1/2 T. CAP. PUSH TROLLEY, COFFING/DUFF LYNX MDL. TP-30P (LOCATION A)
255A 1 1-1/2 T. CAP. PUSH TROLLEY, COFFING/DUFF LYNX MDL. TP-30P (LOCATION A)
256 1 TOE JACK, 50 T. CAP., TK MDL. TJ50AVSL (LOCATION A)
257 1 HAND JACK, 25 T. CAP., SIMPLEX MDL. 25C22 (LOCATION A)
258 1 CHAIN BLOCK HOIST, 3 T. CAP. (LOCATION A)258A 1 CHAIN BLOCK HOIST, 2 T. CAP. (LOCATION A)258B 1 CHAIN BLOCK HOIST, 2 T. CAP. (LOCATION A)259 1 CHAIN BLOCK HOIST, 1 T. CAP. (LOCATION A)
259A 1 CHAIN BLOCK HOIST, 1/2 T. CAP. (LOCATION A)
259B 1 CHAIN BLOCK HOIST, 1/2 T. CAP. (LOCATION A)
260 2 PORTABLE TRUCK SCALES, 200,000 LB. CAP., INTERCOMP MDL. PT300 (LOCATION A)
261 3 LARGE SHACKLES (LOCATION A)262 2 LARGE SHACKLES (LOCATION A)263 2 LARGE SHACKLES (LOCATION A)264 LOT SHACKLES & HOOKS (LOCATION A)265 LOT LIFTING CLAMPS, JET, SAFETY TYPE (LOCATION A)
266 LOT SWIVEL TYPE LIFTING EYES (LOCATION A)267 LOT MATERIAL HANDLING EQUIPMENT: HOOKS, PLATE
DOGS, ETC. (LOCATION A)
268 LOT COME ALONGS, WIRE CABLE TYPE (LOCATION A)
269 LOT TURNBUCKELS (LOCATION A)270 LOT LARGE QUANTITY OF HAMMER WRENCHES
(LOCATION A)271 LOT DRIVE SOCKETS (FOUR BUCKETS) (LOCATION A)
272 LOT BOLT CUTTERS & WIRE CUTTERS, LARGE CAPACITY (LOCATION A)
273 LOT SLEDGE HAMMERS & MAULS (LOCATION A)274 LOT CROWBARS & PRYBARS (LOCATION A)275 LOT LIFTING CHAINS (LOCATION A)276 LOT LIFTING CHAINS (LOCATION A)277 LOT CONTENTS OF RACK: SHACKLES, LIFTING EYES,
HOOKS (LOCATION A)278 LOT CONTENTS OF RACK: LIFTING STRAPS, WIRE ROPE
(LOCATION A)279 LOT CONTENTS OF RACK: ASSORTED LIFTING CHAINS,
RATCHET TYPE HOLD-DOWNS (LOCATION A)
280 2 JACKS, SIMPLEX MDL. 1017, 10 T. CAP. (LOCATION A)
281 2 JACKS, SIMPLEX MDL. 84A, 5 T. CAP. (LOCATION A)
283 LOT LARGE SELECTION OF OPEN END/CLOSED END WRENCHES (LOCATION A)
284 LOT CONTENTS OF SHELF UNIT: OPEN END/CLOSED END WRENCHES, LARGE FUSES, LIFTING CHAINS, OXY./ACY. HOSE & CUTTING TOOLS, LIFTING STRAPS, CAUTION TAPE, ETC. (LOCATION A)
285 LOT RATCHET WRENCHES & TORQUE WRENCH (LOCATION A)
292 1 CORE DRILL, HILTI MDL. DD130-RIG, w/ACCESSORIES (LOCATION A)
306 1 CNC BEAM PUNCH LINE, PEDDINGHAUS 100 T. CAP. MDL. BLP1000/5D, FAGOR 8025GP CNC CONTROLS, (5) PUNCH ASSEMBLIES, PUNCH CAPACITIES: 15/16" THROUGH 1-1/16", 1" DIA. THROUGH 1" AND 1-1/2" DIA. THROUGH 5/8", 2,500 PSI HYD. PRESSURE, 25 HP MOTOR, S/N BPL-120 (LOCATION A)
307 1 CNC AUTOMATED STRUCTURAL BURNING SYSTEM, PEDDINGHAUS MDL. ABCM-1250/3B, FAGOR CNC CONTROL, FOR BURNING PROCESSES SUCH AS FLANGE BEVEL, COPES, BLOCKS, FLANGE THINNING, CUT-OFFS, HAUNCHES, CASTELLATIONS & BEAM SPLITTING, 50" MAX./3" MIN. BEAM WIDTH, 24" MAX. FLANGE HEIGHT, 6" MAX./1/4" MIN. THICKNESS, 4 CONTROLLED AXIS, APPROX. 50' INFEED TABLE, S/N 41441 (LOCATION A)
308 1 HYDRAULIC SHEAR, ROPER WHITNEY PEXTO MDL. 10 H 5, 10 GA. SOFT STEEL CAP., 62" TABLE WIDTH, 48" SQUARING ARM, INCH/METRIC FOBG, 36" CAP. BACKGAUGE, PWR. ADJUSTABLE RAKE ANGLE, 5 HP MOTOR, 208/230/460/3/60 (LOCATION B)
309 1 IRONWORKER, PEDDINGHAUS 55 T. CAP. MDL. 210/13, #432, 3 HP MOTOR, 220/440/3/60, WIRED 220 V., DIES, 4" X 4" X 1/2" ANGLE CAP., 4" X 4" X 3/8" T-SECTION CAP., 7" C CHANNEL, 6" I-BEAM, 1-1/2" SQ. BAR, 1-5/8" RD. BAR, 5/8" X 6" PLATE, PUNCH TOOLING (LOCATION B)
310 1 HYDRAULIC VERTICAL TUBE BENDER, PINES MDL. 5T, REBUILT 2000, BEND CAP. 1-1/4" X 0.065" WALL (1 TUBE)/1" X 0.065" WALL (2 TUBES), 100 DEG. MAX. BEND ANGLE, 40" HEIGHT, 1,000 BENDS PER HOUR PRODUCTION CAP., 20 HP MOTOR, DUAL DIE HOLDERS, S/N 44350-63005 (LOCATION A)
311 1 4-SLIDE MACHINE, NILSON, SYMMETRICAL DESIGN, REEVES VARIABLE SPD. DRIVE SYSTEM, CURRENTLY ARRANGED FLAT STOCK, BEND & PIERCE, S/N N.A. (LOCATION A)
311A 1 C-FRAME PUNCH, WHITNEY-JENSEN MDL. 230, 2 HP, 220/440/3 PHASE, S/N 267-3-69 (LOCATION B)
312 1 PLATE BURNING MACHINE, ARONSON MDL. 1200J, 14'L. X 4'W. (LOCATION A)
313 1 PLASMA CUTTING SYSTEM, THERMALARC MDL. PAK5XR (LOCATION A)
314 1 PORTABLE WELDING MACHINE, MILLER BOBCAT MDL. 250, CC/CV, AC/DC, 10,500 WATT GENERATOR, GASOLINE PWRD., S/N LG085308 (LOCATION A)
315 1 WELDING MACHINE, LINCOLN ELECTRIC MDL. IDEALARC DC-1000, 1,000 AMP, S/N U1980708984 (LOCATION A)
316 1 WELDING MACHINE, MILLER MDL. MP-65E, 650 AMP, MILLER STYLE J-22 WIRE FEEDER, S/N 72-654085 (LOCATION A)
317 1 WELDING MACHINE, HOBART MDL. ARC-MASTER 500, 500 AMP, HOBART COOLING UNIT, HOBART DIGITAL 2000 WIRE FEEDER, S/N 93WS06834 (LOCATION A)
318 1 ARC WELDING POWER SOURCE, MILLER MDL. GOLDSTAR 400 SS DIRECT CURRENT, 230/460/3 PHASE, S/N HK307241 (LOCATION B)
319 1 TUNGSTEN-ARC WELDING POWER SOURCE, MILLER MDL. GOLDSTAR 330A/BP, 300 AMP CAP., AC/DC, SGL. PHASE, 208/230/460, S/N HH089898 (LOCATION B)
320 1 WELDING MACHINE, MILLER MDL. CP-250TS, 250 AMP, MILLER MDL. 24V CONSTANT SPD. WIRE FEEDER, S/N KG090027, MACHINE JA397767 (LOCATION A)
321 1 WELDING MACHINE, MILLER MILLERMATIC MDL. 252, 200 AMP CAP., S/N LH410581B (LOCATION A)
322 1 ARC GOUGER, MILLER, MILLER COOLMATE 3 COOLING UNIT, S/N JB474510 (LOCATION A)
322A 1 PORTABLE WELDER GENERATOR, ONAN MDL. B48M ENGINE, w/MILLER MDL. AEAD-200 LE AC/DC ARC WELDER (LOCATION B)
323 1 SPOT WELDER, WESTERN ARCTRONICS MDL. 15KVA-CT, 15 KVA, SGL. PHASE, 230 v. (LOCATION B)
324A 1 WIRE FEEDER, MILLER MDL. SUITCASE X-TREME 12VS VOLTAGE SENSING TYPE (LOCATION A)
325 1 WIRE FEEDER, MILLER MDL. SUPER S-32P VOLTAGE SENSING TYPE (LOCATION A)
326 1 DIGITAL WIRE FEEDER, MILLER MDL. S54D115V (LOCATION A)
327 1 WIRE FEEDER, LINCOLN, w/MDL. TC-3 MOTION CONTROLLER & FLUX HOPPER (LOCATION A)
328 1 RADIATOR COOLING SYSTEM, MILLER COOLMATE 4 (LOCATION A)
329 1 TRACK BURNER, BUG-O (LOCATION A)330 1 4-WHEEL TORCH CART, w/HOSE & GAUGES
(LOCATION A)
331 1 COIL WINDER, POTTER & RAYFIELD MDL. WV, S/N 2-22-801-5 (LOCATION A)
332 1 COIL CUTTER, POTTER & RAYFIELD MDL. 5127, S/N 7-19-79 (LOCATION A)
333 LOT FOOT CONTROL PEDALS, APPROX. (4) (UNUSED) (LOCATION B)
350 1 VIBRATORY FINISHING MACHINE, HUDSON MDL. HB25VA, 25 CU. FT. CAP., 75" DIA. BOWL, 46" HT., 10 HP MOTOR (LOCATION A)
351 1 VIBRATORY FINISHING MACHINE, SWECO MDL. FMD-20HA, 20 CU. FT. CAP., 57" DIA. BOWL, 54" HEIGHT, 6" DIA. DRAIN, 6" X 12" DISCHARGE DOOR, 10 HP MOTOR, S/N 20FM-469-49 (LOCATION A)
352 1 VIBRATORY FINISHING MACHINE, BRANDON MDL. HB10SM, 10 CU. FT. CAP., 57" DIA. BOWL, 45-1/2" HEIGHT, 10 HP MOTOR, S/N 100201 (LOCATION A)
353 1 VIBRATORY FINISHING MACHINE, GIANT MDL. W-3, 3 CU. FT. CAP., INSIDE DIMS: 28" L-R X 14-1/2" F-B X 10" DP., 1 HP MOTOR, TOTALLY ENCLOSED, SELF-CONTAINED, LOW FRONT LOADING PROFILE, HINGED SOUND COVER, S/N 1056 (LOCATION A)
354 1 VERTICAL AUTOMATIC PANEL SAW, HOLZ-HER 75" X 169" MDL. 1270 "SUPERCUT", NEW 1998, 4 HP MOTOR, 230/3/60, 2" DEPTH OF CUT, 8-5/8" BLADE, AUTO. GRID WALL REPOSITIONING, SUPERCUT SCORING HEAD, SAW HEAD TRAVERSES AUTO. WHEN RIP OR CROSSCUTTING & RETURNS TO STARTING POSITION, SAW CARRIAGE TRAVEL, SPDS: 36 RPM & 72 FPM, 0.75 HP FEED DRIVE, S/N 887/9-802 (LOCATION B)
355 1 VERTICAL AUTOMATIC PANEL SAW, HOLZ-HER 75" X 169" MDL. 1265 "SUPERCUT", NEW 1989, 4 HP MOTOR, 230/3/60, 2" DEPTH OF CUT, 8-5/8" BLADE, AUTO. GRIND WALL REPOSITIONING, S/N 2961/8/910 (LOCATION B)
356 1 TABLE SAW, TANNEWITZ, 44" X 57" TABLE, 16" DIA. WHEEL, RIP STOP, BLADE GUARD, 45 DEG. BLADE TILT, WEIGHT - 2,000 LBS. (LOCATION B)
357 1 TABLE SAW, POWERMATIC MDL. 72, 38" X 48" TABLE w/38" X 62" TABLE EXTENSION, ADJ. RIP STOP, BLADE GUARD, 45 DEG. BLADE TILT, 12"/14" DIA. BLADE, 1" ARBOR, 230/3/60, S/N 472059 (LOCATION B)
358 1 VINTAGE WOODWORKING TOOL CABINET, OLIVER 32"W. X 14" DP. X 71" HT., NUMEROUS CUTTER BLADES & ROUTING BITS (LOCATION B)
360 1 MAGNETIC PARTICLE INSPECTION MACHINE, MAGNAFLUX MDL. DR-1003, 100" CENTERS, 20" RING INTERNAL DIA., S/N 692091 (LOCATION A)
361 1 HYDROSTATIC VALVE TEST STAND, CUSTOM, 28" DIA. TABLE, 45" DIST. BTN. POSTS, 30" MAX. DAYLIGHT, 30" CYL. STROKE, 41" TABLE HEIGHT, OPERATOR"S CONSOLE (LOCATION A)
362 1 HYDRAULIC H-FRAME BRINELL HARDNESS TESTER, LOUIS SMALL (SERVICE PHYSICAL TESTERS) MDL. BT 60 TA 5516, 50" LEFT TO RIGHT HEAD TRAVEL, 65" MAX. WORKPIECE HEIGHT, 28" X 60" WORK BASE, PENDANT CONTROL, BRINELL LOADS TO 4000 KG (LOCATION B)
363 1 OPTICAL COMPARATOR, OGP OPTICON QUALIFIER 30, 30" DIA. SCREEN, 8" X 32' WORKTABLE, SURFACE ILLUMINATION, HEWLETT-PACKARD MDL. 226 COMPUTER SYSTEM, S/N 00300336, GRANITE BASE, 2-AXIS D.R.O., LENS TURRET w/(4) LENSES, AUTO. PART ROTATION ATTACH. (LOCATION A)
364 1 ULTRASONIC TESTER, TESTECH "GANTRY", S/N 0489-536 (LOCATION A)
365 1 BALANCING MACHINE, HOFMANN MDL. Hxe-1215 (SPECIAL), S/N 99-4-174 (LOCATION A)
366 1 BALANCING MACHINE, HOFMANN MDL. Hxe-1215 (SPECIAL), S/N 99-4-175 (LOCATION A)
367 1 HARDNESS TESTER, SERVICE PHYSICAL ROCKWELL C TYPE, w/CABINET STAND (LOCATION B)
368 1 FLATNESS CHECKER, FEDERAL MDL. PR-102, S/N 69317 (LOCATION B)
369 1 PORTABLE ELECTROPLATER, BROOKTRONICS MDL. 20-300, S/N 6233 (LOCATION A)
370 1 BINOCULAR MICROSCOPE, CARL ZEIS MDL. CRW4145-410IKO, MTD. ON 18" X 18" GRANITE SURFACE PLATE (LOCATION A)
371 LOT BINOCULAR MICROSCOPES, NIKON, ARTICULATED STANDS (APPROX. 3), w/LARGE LABORATORY JACK (LOCATION A)
374 1 LABORATORY OVEN, VWR, APPROX. 2' X 2' X 2' INTERIOR DIMS., D.R.O. (LOCATION A)
375 1 INFARED SPECTROPHOTOMETER, PERKIN ELMER MDL. 599B (LOCATION A)
376 1 BENCH CENTER, ASAHI MDL. 2, 19" SWING, 30" DIST. BTN. CENTERS, MTD. TO FABRICATED STAND (LOCATION A)
377 1 BENCH CENTER, RSK, 12" SWING, 19" DIST. BTN. CENTERS (LOCATION A)
378 1 SET-UP TABLE, 60" X 100", 21" HEIGHT, DRILLED & TAPPED FOR 3/4" BOLTS ON 10" CENTERS (LOCATION B)
379 1 GRANITE SURFACE PLATE, 24" X 36" X 6" THK. (LOCATION B)
380 1 GRANITE SURFACE PLATE, 18" X 18" X 3" THK. (LOCATION B)
381 1 GRANITE SURFACE PLATE, 12" X 18" X 4" THK., w/CALIPERS (LOCATION B)
382 1 MACHINIST"S SQUARE, 36" (LOCATION B)390 1 OVERHEAD BRIDGE CRANE, LANDEL 30 T. X
APPROX. 60' SPAN, TOP RUNNING, DBL. GIRDER, BOX BEAM CONSTRUCTION, CENTER DRIVE, YALE UNITIZED HOIST & TROLLEY SYSTEM, 25 HP MAIN HOIST MOTOR, S/N A361 (LOCATION A)
390A 1 LARGE CAPACITY ELECTRIC WINCH SYSTEM, WIRE ROPE CABLE TYPE, 40 HP DRIVE MOTOR, SKID MTD. (LOCATION A)
390B 1 LARGE CAPACITY ELECTRIC WINCH SYSTEM, WIRE ROPE CABLE TYPE, 25 HP ELEC. MOTOR, SKID MTD. (LOCATION A)
390C 1 ELECTRIC WINCH, SKID MTD. (LOCATION A) 391 1 HYDRAULIC VERTICAL DOWNSTROKE CARDBOARD
BALER, GALBREATH MDL. VB2200HD-4054, 54" X 40" X 42" BALE SIZE, SWING AWAY DOOR, FENCE GUARD, OPERATOR"S CONTROL PANEL, 10 HP MOTOR, S/N VB1455 (LOCATION A)
392 1 AIR COMPRESSOR, BAUER MDL. 1 180-E3, ROTARY, 20 HP MOTOR, 22 CFM, 1,300 RPM, 4,000 PSIG PRESSURE, 2-STAGE, GAUGES, ENCLOSED, S/N 32566 (LOCATION A)
392A 1 ROTARY SCREW TYPE AIR COMPRESSOR, KAESER MDL. SIGMA PROFILE SK19, 15 HP (LOCATION B)
393 1 AIR COMPRESSOR, DEVILBISS MDL. 445, 4 CYL. 2-STAGE, 120 GAL. TANK, 900 MAX. RPM, 300 MAX. PSI, BALDOR 10 HP MOTOR, 230/460/3/60 (LOCATION B)
394 1 RECIPROCATING TYPE AIR COMPRESSOR, PONYAIR, 5 HP MOTOR, REFRIGERATED AIR DRYER (LOCATION A)
394A 1 LOW PRESSURE DEHYDRATOR, AIR DRY CORPORATION, H.O.M.: 21, TAG READS: MIL-D-23523-TYPE 2, CLASS 2 MOD, PRESSURE-80-125 PSIG (LOCATION B)
394B 1 HORIZONTAL AIR RECEIVER, BRUNER ENGINEERING & MFG., 200 PSI, 200 GAL. CAP. (LOCATION B)
394C 1 AIR RECEIVING TANK, VERTICAL (LOCATION A)394D 1 AIR RECEIVING TANK, VERTICAL (LOCATION A)394F 1 AIR RECEIVING TANK, HORIZONTAL (LOCATION A)
394G 1 AIR RECEIVING TANK, HORIZONTAL (LOCATION A)
395 1 SANDBLAST POT, w/BLAST MEDIA RECOVERY CABINET (LOCATION A)
396 1 SCISSOR LIFT TABLE, AIR TECHNICAL INDUSTRIES 48" X 48", MDL. SLT-64848-AW, 6K LBS. LIFTING CAP., 8" LOWERED/32" RAISED HEIGHT (LOCATION B)
397 1 SCISSOR LIFT TABLE, AIR TECHNICAL INDUSTRIES 48" X 48", MDL. SLT-64848-AW, 6K LBS. LIFTING CAP., 8" LOWERED/32" RAISED HEIGHT (LOCATION B)
399 1 ENDOVER DRUM ROTATOR, MORSE MDL. 1-300-3, MIX-BLEND-TUMBLE IN CLOSED SHIPPING DRUMS, END-OVER-END ACTION, 800 LBS. CAP., 13 RPM ROTATION SPD., 22-1/2" DIA. X 36" MAX. LENGTH DRUM SIZE, 1 HP MOTOR, S/N 190135 (LOCATION A)
400 1 MOTOR & CONTROL, WESTINGHOUSE 1,250 HP, 4,160 v., 3 PHASE, 1,188 RPM, ELEC. MOTOR DRIVING DUAL VARIABLE DISPLACEMENT PUMPS, MOTOR CONTROLS BY AMERIMEX MOTORS INC. REXROTH PUMPS, 198,000 GPM @ 3,864 PSI (LOCATION A)
401 1 AC MOTOR, GENERAL ELECTRICAL, 125 HP, 460/3/60, 1,775 RPM, 150 AMPS, CODE G, TYPE K, FRAME-405T (LOCATION B)
402 1 AC MOTOR, RELIANCE DUTY MASTER MDL. 1MAF19603-669-UI, 75 HP, 440 v./3 PHASE, 1,765 RPM, 94 AMPS, CODE F, DP ENCLOSURE, INS. CLASS-F, DUTY-CONT. FRAME-365 TY (IN BOX) (LOCATION B)
403 1 INDUCTION MOTOR, SIEMENS/ALLIS, 100 HP, 230/460/3/60, 1,770 RPM, 240/120 AMPS, DUTY CONT., CODE-D, FRAME-404T (LOCATION B)
404 1 INDUCTION MOTOR, WESTINGHOUSE, STYLE 3B9361, 25 HP, 220/440/3/60, 885 RPM, TYPE CS, CLASS 1, FRAME 444, 64/32 AMPS, 2-1/4" SHAFT (LOCATION B)
405 1 AC MOTOR, GENERAL ELECTRIC, 40 HP, 230/460/3/60, 1,775 RPM, 105.8/52.9 AMPS, CODE G, TYPE K, FRAME-302-4T (LOCATION B)
406 1 MOTOR, US ELECTRICAL MOTORS, HIGH THRUST, 40 HP, 230/460/3/60, 1,775 RPM, FRAME-324TP, DESIGN-B, CODE F (LOCATION B)
407 1 MOTOR, 15 HP, 220/440/3/60, 1,745 RPM, 36/18.5 AMPS (LOCATION B)
408 1 DC MOTOR, GENERAL ELECTRIC, 30 HP, 500 v., 1150/3000 RPM, 4.94/1.42 AMPS, CLASS B, ENCLOSURE-DP (LOCATION B)
409 1 AC MOTOR, REULAND MDL. 11674V-XG2687A, 15/2.5 HP, 460 v./3 PHASE, 1300/300, 17.5/7.5 AMPS, TYPE COVO, FRAME-AFC-3650, ENCL.-TEFC, CODE-J, TIME RATING-CONT. (LOCATION B)
410 1 INDUCTION MOTOR, CENTURY, 15 HP, 220/440/3/60, 1,750 RPM, 37/18.5 AMPS (LOCATION B)
411 LOT MOTORS & PUMPS: BALDOR AC MOTOR, 10 HP, 230/460/3/60, 1,725 RPM; GENERAL ELECTRIC AC MOTOR, 5 HP, 1-1/2 HP, 230/460/3/60, 3,450 RPM; US ELECTRIC MOTORS, 1 HP, 230/460 v., 1,745 RPM; GRAY MILLS COOLANT PUMP, 1/8 HP, 230/460 v.; FUJI COOLANT PUMP, 40 WATTS, 230/460 v. (LOCATION B)
413 1 ROTARY PHASE CONVERTER, CEDARBURG MDL. 30A, 3 HP MOTOR, TO START 220 v. MOTORS (LOCATION B)
414 1 TRANSFORMER, FEDERAL PACIFIC, DRY TYPE, CAT. # T43T75, MDL. 36B, PRIMARY VOLTAGE - 480, SECONDARY VOLTAGE - 240/120, 75 KVA, 3 PHASE, 60 Hz (LOCATION B)
414A 1 TRANSFORMER, GENERAL ELECTRIC, CAT. # 9T23B3883, PRIMARY VOLTAGE - 480, SECONDARY VOLTAGE - 240, 45 KVA, 3 PHASE (LOCATION B)
414B 1 TRANSFORMER, GS HEVI-DUTY, DRY TYPE, CAT. # T4H30, HIGH VOLTAGE - 480, LOW VOLTAGE - 240, PRIMARY VOLTAGE - 432-504, 30 KVA, 3 PHASE, 60 Hz (LOCATION B)
414C 1 TRANSFORMER, MGM, DRY TYPE, HIGH VOLTAGE - 480, LOW VOLTAGE - 208/120, 15 KVA, 3 PHASE (LOCATION B)
414F 1 TRANSFORMER, JEFFERSON ELECTRIC, DRY TYPE, POWERFORMER - CAT. # 223-3237, HIGH VOLTAGE - 480, SECONDARY VOLTAGE - 240, 75 KVA, 3 PHASE (LOCATION B)
415 1 TRANSFORMER (LOCATION B)415A 1 TRANSFORMER, ACME, TYPE GENERAL PURPOSE,
PRIMARY VOLTAGE 480 DELTA w/FC TAPS, SECONDARY VOLTAGE 240 DELTA, CATALOG # T-2A-53340-1S (LOCATION B)
415B 1 TRANSFORMER (LOCATION B)416 1 BLOWER, CINCINNATI FAN CO. MDL. BP-12, 3 HP,
3,450 RPM, 5" OUTLET, 208/230/460 (LOCATION B)
417 LOT SHOP UTILITY CARTS (APPROX. 6) (LOCATION B)
418 1 HYDRAULIC UNIT, 1.5 HP, 220/440 v. (LOCATION B)
418A 1 HYDRAULIC UNIT, 3 HP (LOCATION A)419 1 TRIPLEX PUMP, WORTHINGTON MDL. V330H, S/N
56-01064 (LOCATION A)
420 1 TRIPLEX PUMP, WORTHINGTON MDL. V330H, S/N 56-010164A (LOCATION A)
421 1 ELECTRICAL SWITCH GEAR (LOCATION B)421A 1 ELECTRICAL SWITCH GEAR (LOCATION B)421B 1 ELECTRICAL CONTROL CABINET (LOCATION B)421C LOT ELECTRICAL SWITCH GEAR (LOCATION B)422 1 POWER CAPACITOR, SPRAGUE, ECCOL UNIVAR, CAT.
# 6043FE KVAR-60, VOLTAGE - 480, 3 PHASE, GAL. - 24 (LOCATION B)
424 1 HYDRAULIC DIE LIFT TABLE (LOCATION A)425 LOT HYDRAULIC HOSE (LOCATION A)426 1 BANDING CART, w/CLIPS (LOCATION B)427 1 CABINET, STANLEY VIDMAR, 60"W. X 27.5" DP. X
60" HT., (3) SHELVES, DBL. LOCKABLE FRONT DOOR, T-SLOTTED TIE DOWN PAD ON TOP (LOCATION B)
427A 1 COMBINATION SAFE, MOSLER, 22" X 38" X 57" HT. (NEEDS COMBINATION) (LOCATION B)
428 1 NEW STOW & LATCH CART (FOR STORING COLLET SETS, ETC.) (LOCATION A)
428A 1 NEW STOW & LATCH CART (FOR STORING COLLET SETS, ETC.) (LOCATION A)
428B 1 NEW STOW & LATCH CART (FOR STORING COLLET SETS, ETC.) (LOCATION A)
428C 1 NEW STOW & LATCH CART (FOR STORING COLLET SETS, ETC.) (LOCATION A)
428D 1 NEW STOW & LATCH CART (FOR STORING COLLET SETS, ETC.) (LOCATION A)
428F 1 NEW STOW & LATCH CART (FOR STORING COLLET SETS, ETC.) (LOCATION A)
428G 1 NEW STOW & LATCH CART (FOR STORING COLLET SETS, ETC.) (LOCATION A)
429 LOT SHOP CABINETS (LOCATION B)430 LOT SHOP STOOLS (UNUSED) (LOCATION B)431 LOT HARD RUBBER CASTERS, UP TO 8" DIA. (LOCATION
B)432 LOT FILING CABINETS (LOCATION A)433 LOT INSULATED BLANKETS (ON PALLETS) (LOCATION A)
434 1 LOCKABLE BOTTLE STORAGE RACK (LOCATION A)
434A LOT PALLET RACK (43), 9' ARMS, (5) UPRIGHTS, 12' HT. X 42' DP. (LOCATION B)
435 LOT PALLET RACK ARMS, 4'L. & 10'L. (LOCATION A)436 LOT PALLET RACK ARMS, 10'L. (LOCATION A)437 LOT KENMORE FREEZER & G.E. REFRIGERATOR
(LOCATION B)
438 LOT HELPER STANDS (TWO PALLETS) (LOCATION B)439 LOT AIR HOSE (LOCATION B)440 LOT WORKBENCHES & CONTENTS (LOCATION B)441 LOT WAREHOUSE LADDERS, 10' & 5' HT. (LOCATION B)
442 LOT BARREL RACKS (LOCATION B)443 LOT MISC. SHOP CABINETS & FURNITURE (LOCATION B)
443A LOT MISC. SHOP CABINETS & FURNITURE (LOCATION B)
443B LOT MISC. SHOP CABINETS & FURNITURE (LOCATION B)
443C LOT MISC. SHOP CABINETS & FURNITURE (LOCATION B)
443D LOT MISC. SHOP CABINETS & FURNITURE (LOCATION B)
444 1 METAL SHOP TABLE/CABINET, HEAVY DUTY, 24" X 72" X 24" HT., STORAGE COMPARTMENT (LOCATION B)
444A 1 STAINLESS STEEL TANK (LOCATION B) 444B 1 METAL SHOP TABLE, H.D., w/BENCH VISE & BENCH
SHEAR (LOCATION B)444C LOT STEEL SHOP TABLES, (3) 60" X 34" X 34" HT.
w/LOWER SHELF, (1) TRADESMAN BENCH, 72" X 27" X 34" HT. w/LOWER SHELF (LOCATION B)
445 LOT SHOVELS & PITCH FORKS (LOCATION B)446 1 TRUCK BUMPER, H.D., FOR 1 T. TRUCK, 450 LB.
WEIGHT (LOCATION B)446A 1 ALUMINUM TABLE, 46" X 52" X 31" HT., w/LOWER
SHELF (LOCATION B)447 1 DUMP HOPPER, ROURA (LOCATION B)448 LOT METAL TUBS (LOCATION B)
448A LOT SHOP & OFFICE DESKS (LOCATION B)449 LOT BUILDING MATERIALS: 4' X 12' SECTIONS OF
SHEETROCK, 2 X 4 & (6) 4' X 8' X 1/2" THK. PLYWOOD, (6) 4' X 8' X 5/8" THK. PLYWOOD w/RADIANT BARRIER COATING (LOCATION B)
450 1 GOLF CART, EZGO, NEW 2009, w/CHARGER, 48 v., VERY CLEAN, S/N 5080688 (LOCATION A)
451 1 GOLF CART, EZGO, NEW 2009, w/CHARGER, 48 v., VERY CLEAN, S/N 5080709 (LOCATION A)
452 1 UTILITY TRUCK, CUSHMAN, PROPANE, TRUCK BED, MOTOR RECENTLY REPLACED (LOCATION B)
453 1 HUNTING RACK, FOR VEHICLE MOUNTING (LOCATION B)
