Embed Size (px)
Citation preview
®
IL2896a
VERTICAL CONTACT TOASTER
MODELVCTE13M VCTE13S
Installation and Operation
Instructions2M-Z19277 Rev. C 10/13/2015
VCTE13 & VCT13E(Shown with optional butter wheel)
®®
®®
2
2
These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCENOTICE
Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability.Star reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.Due to periodic changes in designs, methods, procedures, policies and regulations, the specifications contained in this sheet are subject to change without notice. While Star International Holdings Inc., Company exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the specifications. By using the information provided, the user assumes all risks in connection with such use.
MAINTENANCE AND REPAIRSContact your local authorized service agent for service or required maintenance. Please record the model number, serial number, voltage and purchase date in the area below and have it ready when you call to ensure a faster service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
Business 8:00 am to 4:30 p.m. Central Standard Time Hours:
Telephone: (314) 678-6303
Fax: (314) 781-2714
E-mail [email protected]
Website: www.star-mfg.com
Service Help Desk
Authorized Service Agent ListingReference the listing provided with the unit orfor an updated listing go to:Website: www.star-mfg.com E-mail [email protected]
Mailing Address: Star International Holdings Inc., Company 10 Sunnen Drive St. Louis, MO 63143 U.S.A
1
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
18.57”
20.85”
22.78”
IL2897
TABLE OF CONTENTSSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Uncrating & Inspecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Assembly & Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Toaster Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Daily Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-14
SPECIFICATIONS
Electrical SpecificationsModel Voltage Hz Ph Amps Watts Powercord
VCTE13M208V 60
1
13.5 2800 6-20P230V 50 12 2750 CEE7/VII240V
6012.5 3000 6-20P
VCTE13S208V 12.25 2550 6-20P230V 50 10.5 2450 CEE7/VII240V 60 11 2650 6-20P
VCT13M208V 60
1
13.5 2800 6-20P230V 50 12 2750 CEE7/VII240V
6012.5 3000 6-20P
VCT13S208V 12.25 2550 6-20P230V 50 10.5 2450 CEE7/VII240V 60 11 2650 6-20P
2
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
IL2898
A B
C
D
E
G
HI
F
Nameplate
J
L
K
F
FEATURES & BENEFITS
A Burn Guard Protects users from touching the conveyor beltB Conveyor Takes the heel and crown separately through their toasting processC Upper Platen Assy Heating surface designed to toast the product as it slides across the surface D Optional Butter Wheel Saves time for preparing buns for toastingE Platen Height Knob Controls the height of the upper platen
F High LimitInterrupts the heater tube connections if the air temperature platen exceeds 550°F (287°C). It automatically resets when the air temperature drops below 425°F (218°C)
G Toaster Chute Removable Chute returns product for easy access.H Foot Silicone foot keeps unit firmly in place.I Control Board Controls the conveyor speeds, turns unit on & off. (manual controls differ)
J Locking Platen Latch Keeps the upper platen in the down position.K Platen Height Indicator Indicates the height of the upper platen
L Non-Stick Sheet Non-Stick surface between the upper platen and the product, allowing the product to slide easily through the toasting process.
3
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
erGENERAL INFORMATION
This equipment is designed and sold for commercial use only by personnel trained and experienced in its operation and is not sold for consumer use in and around the home nor for use directly by the general public in food service locations.Before using your new equipment, read and understand all the instructions & labels associated with the unit prior to putting it into operation. Make sure all people associated with its use understand the units operation & safety before they use the unit.
INSPECTION UN-CRATING AND INSPECTINGUnpack the unit and components from the shipping container. Remove all visible packing material and those from inside the cooking chamber. If damage is discovered, file a claim immediately with the carrier that handled the shipment. Do not operate the unit if it was damaged during shipping. All shipping containers should be checked for freight damage both visible and concealed. This unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If equipment is received in damaged condition, either apparent or concealed, a claim must be made with the delivering carrier.Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a request for inspection of concealed damage must be made with carrier within 15 days. Be certain to retain all contents plus external and internal packaging materials for inspection. The carrier will make an inspection and will supply necessary claim forms.
ELECTRICAL CONNECTION Disconnect the unit from the power source before installing or removing any parts. Be absolutely sure that the ground connection for the receptacle is properly wired. Do not connect equipment to power without proper ground connections. Improper grounding may result in personal injury or death.
Allow enough space around the toaster for adequate ventilation. Do not operate the unit without the crumb tray properly positioned. Overheating and poor toasting may occur. Read all labels on the unit and follow their instructions.
Before making any electrical connection to this unit, check that the power supply is adequate for the voltage, amperage and requirements stated on the rating plate. A wiring diagram is included.
DO NOT CUT OR REMOVE THIS PLUG OR THE GROUNDING PRONG FROM THE PLUG. FAILURE TO COMPLY MAY RESULT IN DEATH OR SERIOUS INJURY.
CONNECT/PLUG UNIT INTO DEDICATED A. C. LINE ONLY SPECIFIED ON THE DATA PLATE OF THE UNIT.
SOME SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE SHOULD BE TAKEN WHILE USING THIS UNIT.
CAUTION
CAUTION
CAUTION
WARNING
WARNING
WARNING
4
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
ASSEMBLY AND INSTALLATIONThe unit was shipped fully assembled and ready to plug into a standard outlet specified for its voltage and amp draw. If improper electrical supply is determined, contact a qualified electrician prior to using the unit. Removal and replacement of the power cord and plug voids the warranty. For assistance, contact your local authorized service agent for service or required maintenance.1. Place the unit in its operating location.2. Wipe down the exterior with a damp cloth.3. Place the Toaster Chute into position.4. Unlock the Platen Latch and lower the
platen.5. Loosen the sheet retainer and install the
non-stick sheet into position, and secure.6. Raise the platen and latch in place.
CAUTIONFailure to use non-stick sheets can lead to damaging the unit and a loss of warranty. Non-stick sheets are not a warranty item.
TOASTER SETTINGSBefore using the unit for the first time, test the pass time of the conveyor belt. The pass time through the toaster should be between 8 to 12 seconds for standard setting.1. Turn unit ON and wait for it to complete the
PRE-HEAT process.2. Set the Platen height by adjusting the two (2) Platen Height Knobs on top of the unit.3. Make sure the platen lock is on.4. Place a bun on the conveyor belt, cut side up, “HEEL” on one side and
“CROWN” on the other.
IF TO DARK: Decrease TEMP.
IF TO LIGHT: Increase TEMP, or move platen closer to conveyor
Non-Stick Sheet
Platen Latch
Toaster Chute
Sheet Retainer
IL2899a
5
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
erDAILY OPERATION
CHANGING TEMPERATURE1. Push and hold the "SET TEMP" button for three seconds.2. The display will flash the current top temperature setting.3. Using the ↑ and ↓ adjust the top heat to desired temperature (increments
of 10°)4. Press the "SET TEMP" button again to change the bottom heat setting.5. Using the ↑ and ↓ adjust the bottom heating setting (0 – 10).6. Press the "SET TEMP" button again to save the settings and exit program
mode.
CHANGING CONVEYOR SPEED1. Push and hold the ↑ and ↓ for three seconds2. Using the ↑ and ↓ adjust the motor speed to the desired
setting (1 through 99)3. Press the "SET TEMP" button to exit the program
CHECK TEMPERATURE SETTING1. Press the "SET TEMP" button to check the platen temperature.
CLEAN MODE1. Press the "CLEAN" button to enter the clean mode
a. Elements will be turned OFF and the belt will continue to runb. The screen will flash CLEAN and WAIT.c. When the platen has lowered to a safe temperature the screen will flash CLEAN and READY.
2. Press the "ON/OFF" button to exit the clean mode.
CHANGING BUN THICKNESS SETTING1. Set the "Height Adjustment Knobs" to their desired settings.2. Turn unit ON, allow to warm-up before proceeding.3. Place buns on the conveyor, cut side facing the front of the toaster.4. Toasted buns will drop down the toaster chute.5. Turn the "Height Adjustment Knobs" move the platen towards
the conveyor for darker buns, move the platen away from the conveyor for lighter buns.
Height Adjusting Knob
Height Indicator
IL2900
IL2856
RUN CLEAN
SETTEMP
ONOFF
6
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
POWERON (I)
OFF (O)
MAINPOWER
ELEMENTPOWER
VERTICAL CONTACTTOASTER
OFF
150
200
250300350
400
450
500
550
VCT
IL2922
Height Adjusting Knob
Height Indicator
IL2900
DAILY OPERATION MANUAL CONTROL
OPERATING1. Turn the Power Switch to the "ON" position2. The conveyor belt will begin to move.3. Using Temperature Knob, move it from the "OFF" position to your desired
temperature.4. The Element Power Light will turn "ON" when the unit is calling for heat.
When your desired temperature is reached, the light will turn "OFF". Wait for the Element Power Light to cycle twice before using.
5. When finished using, turn the Temperature Knob to the "OFF" position, but leave the Power Switch in the "ON" position to allow the cooling fan to run.
6. Once cooled, move the switch to the "OFF" position.
CHANGING CONVEYOR SPEEDChanging conveyor speed is only capable on the electronically controlled units.
CERTAIN SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE SHOULD BE TAKEN WHILE USING THIS UNIT.
CHANGING BUN THICKNESS SETTING1. Set the "Height Adjustment Knobs" to their desired settings.2. Turn unit ON, allow to warm-up before proceeding.3. Place buns on the conveyor, cut side up.4. Toasted buns will drop down the toaster chute.5. Turn the "Height Adjustment Knobs" to lower the platen for darker
buns, raise for lighter buns.
CAUTION
7
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
erCLEANING
Preventive maintenance for your Ultra-Max contact toaster consists of the following recommended cleaning procedures. To keep your toaster in top operating condition, these steps should be performed daily or weekly as indicated.
Daily Cleaning1. MANUAL: Turn the temp knob to the "OFF" position, and the power switch in the "ON" position. ELECTRONIC: Press and hold the CLEAN button to enter cleaning mode.
a. The screen will flash “CLEAN” “WAIT” while the unit cools down to a safe temperature.b. Unlock platen using knob on side, raise the platen and prop open to speed up cool down. Always
remove Butter before raising platen if used.c. The screen will flash “CLEAN” “READY” when the unit has cooled to a safe temperature.
IMPORTANT: Allow the unit to cool before attempting to clean it.2. Wipe down moving belt with mild detergent and damp cloth
(an abrasive pad can be used on metal belt).3. Wipe down exterior of toaster with mild detergent and damp cloth.4. Remove non-stick sheet and clean with mild detergent and damp cloth. (If excess buildup is unable to
be removed and causing buns to stick to the sheet, a new sheet may need to be installed.)5. Remove toaster chute and wash in a sink with mild detergent.6. Dry and return toaster chute, and non-stick sheet back into position.
DO NOT IMMERSE OR LET THE UNIT STAND IN WATER. DO NOT HOSE DOWN THE UNIT OR THE TABLE/COUNTER IF THE UNIT IS ON THE TABLE/COUNTER.KEEP AWAY FROM RUNNING WATER.
DO NOT use caustic cleaners on any surface of the unit, conveyor belt or the non-stick sheet
WARNING
CAUTION
Non-Stick Sheet
Platen Latch
Toaster Chute
Sheet Retainer
IL2899a
8
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
TROUBLESHOOTING GUIDE A. Unit Will Not Heat, Conveyor Belt Will Not Move. 1) Be sure the main circuit breaker is switched to the ON 2) Check to see if the toaster is plugged in and all controls are turned to the ON position.
B. Unit Has Heat Only On One Side, Conveyor Belt Turns Freely. 1) Contact your local service agent,, as heating element may need replacing.
C. Conveyor Will Not Turn, Unit Heats Properly. To check for mechanical binding: 1) DISCONNECT UNIT FROM POWER SOURCE. 3) Remove 4 screws on the back of the toaster and remove back panel. 4) Remove the right side panel. 5) Loosen the four screws that hold the drive motor in place. 6) Slide the motor up allowing the drive chain to be removed from the sprockets. 7) Move the conveyor belt by hand to check for mechanical binding. If conveyor moves freely, contact your local service agent,, as the drive motor and/or speed control may need replacing. 8) Re-install the rear and side panels.
D. Heat Limit Switch (Reset) Your Ultra-Max contact toaster is equipped with an automatically activated heat limit switch that interrupts the heater tube connections if the ambient temperature in the platten assembly exceeds 550°F (287°C). This switch resets automanually when the temperatuer reaches 425°F (218°C) shown in the Features & Benifits Illustration on page 2.
E. Conveyor Turns at One Speed Regardless of Speed Control Setting. 1) Contact your local service agent,, as speed control should be replaced.
F. Product Sticking To Conveyor or Slide Your Ultra-Max contact toaster is designed to toast product that is current room temperature. DO NOT attempt to put frozen or refrigerated material into the contact toaster. Doing so may cause it to come out doughy or very moist, as well as possibly sticking to parts of the unit. Follow the cleaning procedures.
9
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
erMAINTENANCE PROCEDURES
A. Replacing the Bottom Element 1) DISCONNECT UNIT FROM POWER SOURCE. 2) Remove the side panels and bottom panel. 3) Remove element wire from terminal block connection, keeping top and bottom wires separate. 4) Lift element retainers by loosening retaining screws and removing the retainer plate up. 5) Gently, pull defective element out of unit. 6) Gently, put new element into unit. 7) Slide the retainer back into place. Tighten the screw to secure the retainer in place over the ends of the elements.
B. Replacing the Fan Motor 1) DISCONNECT UNIT FROM POWER SOURCE. 2) Remove the toaster slide. 3) Remove screws from the bottom panel. 4) Unplug power supply cord from fan motor. 5) Remove (4) screws, which hold fan motor and grill to bottom of unit and remove fan. 6) Put replacement motor and grill in place and secure to the bottom of unit with screws. 7) Reconnect power supply cord to fan motor. 8) Replace bottom panel. Fasten with screws removed in step 2.
C. Replacing the Belt Drive Motor 1) DISCONNECT UNIT FROM POWER SOURCE. 2) Remove the right side and bottom panels. 3) Remove sprocket from motor shaft, using an Allen wrench and loosening the set-screw. 4) Remove the wire from terminal block connecting the drive motor to internal wiring. On units rated 208 or 240 volts, note which color leads are being used for these connections and which lead is capped with white tape. The new motor should use the same arrangement. 5) Remove screws holding motor in place and remove motor from unit. 6) Put new motor in place and attach loosely with mounting screws. 7) Replace sprocket on motor shaft.NOTE The two sprockets should line up parallel with each other, so the chain does not twist any during operation. Also the hub gets installed closets to the motor. 8) Slide motor until the drive chain has about 1/4” slack when lightly pushed at the center of its top open run. See chain tensioning illustration. 9) Tighten screws to secure motor. 10) Rewire leads same as removed in step 4. 11) Replace previously removed panels.
D. Clean the Air Intake (Once A Week) 1) DISCONNECT UNIT FROM POWER SOURCE. 2) Place unit on its backside. 3) Use a vacuum cleaner and or a damp cloth to clean the air intake.
E. Lubricate the Chain & Sprockets (Every 6 Months) 1) DISCONNECT UNIT FROM POWER SOURCE. 2) Remove enclosure exposing chain drive. 3) While wearing rubber gloves and using an extreme pressure, synthetic chain lubricant with a temperature range up to 400°F (204°C) lubricate chain and sprockets. Apply liberally. This grease is available as part no. 1L-Z12397 . 4) Replace enclosure, Reconnect power source and test unit.
1/4”
Chain Tension
10
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
DISCONNECT THE POWER SUPPLY BEFORE SERVICING OR CLEANING THIS UNIT. SAFEGUARD THE POWER SO IT CANNOT BE ACCIDENTALLY RESTORED. FAILURE TO DO SO COULD RESULT IN DISMEMBERMENT, ELECTROCUTION, OR FATAL INJURY.
MAINTENANCE continuedREMOVING & REPLACING SILICONE BELT1. Disconnect unit from power allow to cool before beginning process.2. Remove guard from in front of the belt.3. Rotate belt by hand until belt seam is visible.4. The Idler Shaft is spring loaded. Press on the front idler shaft to remove tension from the
belt. (Continuous pressure is required).5. Pull splicing rod from belt.6. Carefully release pressure from idler shaft so the roller is not propelled from the unit by the
springs.7. Installation is similar to removal. Feed the belt around the drive shaft and idler shaft rollers
making sure the tracking guide on the backside of the belt is seated in the roller grooves.8. Press the front roller to create slack in the belt.9. Feed the splicing rod through the two ends of the belt.10. Remove pressure from roller and install belt guard.11. Plug unit back into outlet and test for proper operation.
Drive Shaft
Groove
Burn Guard
LockingPlatenLatch
Idler Shaft
IL2901
Above: Removing and Installing Silicone Belt
CAUTION
11
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
2M-4497-2 11/21/14
The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.
FOR ASSISTANCE
Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.
ALL:* Pop-Up Toasters* Butter Dispensers* Pretzel Merchandisers (Model 16PD-A Only)* Pastry Display Cabinets* Nacho Chip Merchandisers* Accessories of any kind* Sneeze Guards* Pizza Ovens (Model PO12 Only)* Heat Lamps* Pumps-Manual
Visit our Website at: www.star-mfg.com Email: [email protected]
THOROUGHLY INSPECT YOUR UNIT ON ARRIVALThis unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the transportation company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of the unit.
LIMITED EQUIPMENT WARRANTYAll workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is limited to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited to the repair of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below) should be taken to the closest Star service agency, transportation prepaid.
> Star will not assume any responsibility for loss of revenue.
> On all shipments outside the United States and Canada, see International Warranty.
* The warranty period for the Ultra-Max, Hot Plates, Griddles, Charbroilers is (3) years parts & labor.
* The warranty period for the Star-Max, Charbroilers, Griddles, Hot Plates, Fryers & Finishing Oven is (2) years parts & labor.
* The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.
* ThewarrantyperiodfortheChrome-MaxGriddlesisfive(5)yearsonthegriddlesurface.Seedetailedwarrantyprovidedwithunit.
* The warranty period for Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to Dura-Teccoatingsfromimpropercleaning,maintenance,useofmetallicutensils,orabrasivecleaners,abrasivepads,productidentifiersand point-of-sale attachments, or any other non-food object tha comes in continuous contact with the roller coating. This warranty does not apply to the “non-stick” properties of such materials.
> This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts and ninety (90) days on labor.
> This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or the Service Center's sub-agency.
> This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and Operating instructions.
> This warranty is not valid on Conveyor Ovens unless a "start-up/check-out" has been performed by a Factory Authorized Technician.
PARTS WARRANTYParts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted, the labor to replace the part is NOT warranted.
SERVICES NOT COVERED BY WARRANTY
PORTABLE EQUIPMENTStar will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below. These products should be taken to the Service Agency for repair:
1. Traveltimeandmileagerenderedbeyondthe50mileradiuslimit 2. Mileage and travel time on portable equipment (see below) 3. Labor to replace such items that can be replaced easily during a daily cleaning routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc. 4. Installation of equipment5. Damagesduetoimproperinstallation 6. Damages from abuse or misuse 7. Operated contrary to the Operating and Installation Instructions 8. Cleaning of equipment 9. Seasoning of griddle plates
10. Voltage conversions11. Gas conversions12. Pilot light adjustment13. Miscellaneous adjustments14. Thermostat calibration and by-pass adjustment15. Resettingofcircuitbreakersorsafetycontrolsorresetbuttons16. Replacementofbulbs17. Replacementoffuses18. Repairofdamagecreatedduringtransit,delivery,& installationORcreatedbyactsofGod
* TheModel510FD,510FFFryer.* TheModel526TOAToasterOven. * TheModelJ4R,4oz.PopcornMachine. *TheModel518CMA&526CMACheeseMelter.* TheModel12MC&15MC&18MCPHotFoodMerchandisers.* TheModel12NCPW&15NCPWNachoChip/PopcornWarmer.* All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers.* All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer. * All Condiment Dispensers except the Model HPD & SPD Series Dispenser.* All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series.* AllQCS/RCSSeriesToastersexcept Model QCS3 & RCS3 Series.* All Fast Steamer Models except Direct Connect Series.
12
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
FAN
CONVEYORMOTOR
TOP ELEMENT
BOTTOM ELEMENTS
HI-TEMPSWITCH
HB
1
120V
240V
240V
120V
120V
L1 F1 M1 OT2
HT1
L2M
2F2
OT1
HB2
HT2
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
DATE
TOLERANCES UNLESS OTHERWISE NOTEDFRACTIONS ±1/64 DECIMALS ±.015 ANGLES ±1°
STAR MANUFACTURING INTERNATIONAL INC.#10 SUNNEN DRIVE, ST. LOUIS, MO. 63143, USA
CK.
MATERIAL
FINISH
PART NO.
DESCRIPTION OF CHANGEREVISIONS
MODEL NO.
TITLE
DATELTR DRDR.
- --
--
MH
SK-2798HCTEWIRING DIAGRAM, PARALLEL BOTTOM
-
-MRC 7/11/14
FAN
CONVEYORMOTOR
TOP ELEMENT
BOTTOM ELEMENT
HI-TEMPSWITCH
HB1HT1
L1 F1 M1
L2O
T2M
2F2
OT1
HB2
HT2
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
DATE
TOLERANCES UNLESS OTHERWISE NOTEDFRACTIONS ±1/64 DECIMALS ±.015 ANGLES ±1°
STAR MANUFACTURING INTERNATIONAL INC.#10 SUNNEN DRIVE, ST. LOUIS, MO. 63143, USA
CK.
MATERIAL
FINISH
PART NO.
DESCRIPTION OF CHANGEREVISIONS
MODEL NO.
TITLE
DATELTR DRDR.
- --
--
MH
SK-2799HCTEWIRING DIAGRAM, SINGLE BOTTOM
-
-MRC 7/11/14
120V
240V
240V
120V
120V
13
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
DATE
TOLERANCES UNLESS OTHERWISE NOTEDFRACTIONS ±1/64 DECIMALS ±.015 ANGLES ±1°
STAR MANUFACTURING INTERNATIONAL INC.#10 SUNNEN DRIVE, ST. LOUIS, MO. 63143, USA
CK.
MATERIAL
FINISH
PART NO.
DESCRIPTION OF CHANGEREVISIONS
MODEL NO.
TITLE
DATELTR DRDR.
- --
--
MH
SK-2823HCT13MWIRING DIAGRAM, PARALLEL BOTTOM
-
-MRC 10/23/14
FAN
CONVEYORMOTOR
TOP ELEMENT
BOTTOM ELEMENTS
HI-TEMPSWITCH
THERMOSTATAUX. AUX.
ELEMENTLIGHT
POWERLIGHT
TOGGLESWITCH
NOTE: WIRE #'S REFER TO STAR DWG2E-Z19338-WIRING KIT, HCT
#1 #2
#3
#3
#6
#5
#5
#4
#7
#8
#9
#10
#10
#11
#12
#13
STAR MANUFACTURING INTERNATIONAL INC.#10 SUNNEN DRIVE, ST. LOUIS, MO. 63143, USA
FAN
CONVEYORMOTOR
TOP ELEMENT
BOTTOM ELEMENT
HI-TEMPSWITCH
AUX. AUX.
ELEMENTLIGHT
POWERLIGHT
TOGGLESWITCH
NOTE: WIRE #'S REFER TO STAR DWG2E-Z19338-WIRING KIT, HCT
#1 #2
#3
#3
#6
#5
#4
#7
#8
#9
#10
#10
#11
#12
#13
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
DATE
TOLERANCES UNLESS OTHERWISE NOTEDFRACTIONS ±1/64 DECIMALS ±.015 ANGLES ±1°
CK.
MATERIAL
FINISH
PART NO.
DESCRIPTION OF CHANGEREVISIONS
MODEL NO.
TITLE
DATELTR DRDR.
- --
--
MH
SK-2824HCT13SWIRING DIAGRAM, SINGLE BOTTOM
-
-MRC 10/23/14
THERMOSTAT
14
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
SK2817, Rev. A, 11/07/14Model: VCTE13Vertical Contact Toaster
43
8
5
6
64
6869
71
70
6566
67
10 1112
13 14
1
2
1516
2021 22
23 24
25
26
35
36
1638
30
72
40
45333046
32
Nameplate
5557
58
56
54 27
53 30 29
5960 61
6263
48
47 49 50
5152
43
4434 41
42
33
39
3037
34
27 28 29 3031
32
17
18
19
7
9
Optional AccessoryVCT13 Manual Control
VCTE13 Electonic Control
15
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
erPARTS LIST October 13, 2015, Rev. C
Model: VCTE13 Vertical Contact ToasterFig. No Part Number Quantity Description Application
1HC-CT0018
OptionalBUTTER WHEEL WELDMENT
HC-CT0027 BUTTER WHEEL WLDMT, 5”
2HC-CT0019
OptionalBUTTER WHEEL BASE ASSY
HC-CT0028 BUTTER WHEEL BASE ASSY 5”3 2H-Z18588 1 PTFE SHEET, 0.003 TK, 13 X 15.754 2F-Z19083 1 13” TOP CASTING5 2N-Z17710 1 ELEMENT, METAL 2300W 240V, 230V5 2N-Z17749 1 ELEMENT, METAL 2300W 208V6 HC-Z17711 1 ELEMENT COVER7 HC-Z17724 1 THERMOPROBE BRKT VCTE138 2C-Z13630 1 HALF CLAMP, .250 DIA.9 2E-Z17719 1 TYPE K PROBE VCTE13
10 2A-Z17712 3 THUMBSCREW 8-32 X .37511 HC-Z17713 1 RETAINER, PTFE SHEET12 HC-CT0021 1 PLATEN COVER ASM13 2C-A6153 1 SCR,MS HH 1/4-20X1/2 18-814 2R-Y6762 1 HANDLE-DIMCO GRAY 19015 2K-Z17714 2 BUSHING, OUTER16 2K-Z17715 2 BUSHING, INNER17 2C-1512 13 SCREW 10-24X3/8 RHP STL18 2C-6517 4 NUT 1/4-20 HEX STL NP19 2A-Z17716 2 SUPPORT, 1/4-20 X 11/3220 2M-Z17735 1 LABEL, HEEL21 2M-Z17750 1 LABEL, CROWN22 HC-CT0023 1 BELT GUARD ASM
232A-CT0016
1BELT IDLER SHAFT ASSEMBLY VCTE13M
2A-CT0016SB BELT IDLER SHAFT ASSEMBLY VCTE13S24 2P-200700 2 BEARING-PTFE SPRING LOAD25 2P-Z18587 2 BEARING SPRING 2IN26 2T-30401-30 1 STAT FXD 550°F OPEN27 2K-200464 3 BUSHING, WIRE RING 7/8”
282N-Z17718 2 ELEMENT, METAL 350W 240V VCTE13M, VCT13M2N-Z17718 1 ELEMENT, METAL 350W 240V VCTE13S, VCT13S
29 HC-Z19153 2 ELEMENT SUPPORT30 2C-Z6929 33 10-24 KEPS NUT S.S.31 HC-Z19160 1 PANEL, RIGHT COVER32 2C-6349 16 SCREW #8X3/8 B THP STL NP33 HA-112261 2 BEARING ASSY, PTFE/BRONZE34 2C-200014 4 SCREW 8-32X3/8 THP SS35 2V-Z17744 1 PLATEN SUPPORT36 2C-1810 10 WASHER 3/16 BURR STL NP
16
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
PARTS LIST October 13, 2015, Rev. C
Model: VCTE13 Vertical Contact ToasterFig. No Part Number Quantity Description Application
37 2A-CT0011 2 ADJUSTMENT KNOB ASY
38HC-CT0012 1 LEFT ADJUSTMENT BRKT ASYHC-CT0013 1 RIGHT ADJUSTMENT BRKT ASY
39 HC-Z19157 1 TOAST SLIDE40 2M-Z19165 1 LABEL, VCTE VCTE1341 2J-Z17717 1 ELECTRONIC CONTROL SPEC VCTE1342 2R-Z18201 4 FOOT 1.69X1 SIL 1/4 20
432E-Z10406
1TERMINAL BLOCK 4 POS VCTE13
2E-Z14254 TERMINAL BLOCK 6-POLE VCT1344 2U-200592 1 QCSE POWER BOARD
452A-CT0015 1 BELT DRIVE SHAFT ASSEMBLY VCTE13M, VCT13M2A-CT0015SB 1 BELT DRIVE SHAFT ASSEMBLY VCTE13S, VCT13S
46 2P-200646 1 SPROCKET, 25B20 X 5/1647 2P-200648 1 SPROCKET, 25B32 X 5/1648 2P-Z19167 1 CHAIN #25 15.5” 62 LINKS49 2E-Z17514 1 SPEED SENSOR VCTE1350 HC-CT0008 1 SPEED CONTROL BRKT ASY51 2U-Z9657 1 MOTOR AC 11 RPM CW52 2K-Y3240 1 BUSHING HEYCO SR 17-253 HC-Z19158 1 ELEMENT RETAINER54 HC-Z19154 1 AIR DEFLECTOR55 HC-CT0014 1 PLATEN LATCH ASY
562M-Z18512 1 LABEL, LOCK SYMBOL2M-Z18513 1 LABEL, UNLOCK SYMBOL
57 2R-Z17729 1 KNOB, 1-1/4 X 5/8 X 1/258 HC-Z19161 1 PANEL, LEFT COVER59 2C-Z5883 4 10-24 X 1/2 FZA SCREW60 2R-200562 1 FAN GUARD61 HC-Z17740 1 MOTOR HOUSING COVER62 2U-200561 1 MOTOR,FAN240V 23BTM63 2M-Z18258 2 LABEL, SCALE64 2T-Z18396 1 THERMOSTAT, 150-550F VCT1365 2M-Z19358 1 OVERLAY, VCT VCT1366 HC-CT0031 1 KNOB ASSEMBLY VCT1367 2J-31157 2 LIGHT SIGNAL RED VCT1368 2I-05-07-0013 1 BOOT SWITCH VCT1369 2M-Z18461 1 LABEL, POWER, ON AND OFF VCT1370 Z1-70-07-0343 1 SWITCH GUARD VCT1371 2E-30330 1 SWITCH ON OFF TOGGLE 20A VCT1372 2A-Z19162 1 ROD. S.S. 5/16 DIANI 2B-Z19166 1 CONVEYOR BELT CG10 X .062 VCTE13MNI PS-CT0035 1 SILICONE BELT, 13” X 31.38” VCTE13SNI HA-120244 1 CORDSET ASSY QCS1-230C 230VNI HA-120245 1 CORDSET ASSY NEMA 6-20P 208,240V
17
2M-Z
1927
7; H
olm
an V
ertic
al C
onta
ct T
oast
er
STAR INTERNATIONAL HOLDINGS INC. COMPANYStar - Holman - Lang - Wells - Bloomfield - Toastmaster
10 Sunnen Drive, St. Louis, MO 63143 U.S.A.(314) 678-6303
www.star-mfg.com
