Hobart model 5216 Meat Saw

INSTRUCTION MANUAL. . . with Catalog of Replacement Parts

HOBARTMODEL - 5216 MEAT SAW

Spec. #9250 (60 Cy.)

Spec. #9580 (50 Cy.)

VHOBART^ The World's Oldest and Largest Manufacturer of Computing Scalesand Food Store, Kitchen, Bakery and Dishwashing Machines

THE HOBART MANUFACTURING COMPANY TROY, OHIOFORM 4276-B (Revised Nov. 1964) (Supersedes Form 4276-A, Jan. 1964)

INSTRUCTIONS 5216

Fig. 1

Installation, Operation and Care of

MODEL 5216 MEAT SAWA. UNPACKING

A.I Remove the shipping box that coversthe saw. Next, unpack the followingparts that were disassembled forshipping purposes; table assembly,carriage assembly, carriage supportassembly, saw blade, front wiper as-sembly, rear wiper assembly, switchpush rod, and feet. The pusher plateis packed in the scrap pan in the basecompartment. Remove the four re-taining bolts from the underside ofthe skid.

B. SETTING UP (Installation)B.I Place the machine in the location

where it is to be used. Re-assemblethe feet (1, Fig. 1). Place a spiritlevel on top of the base unit and ad-

just the feet in the legs so that thebase unit is level from side to sideand front to back. Lock feet in place,using set screws furnished.

B.2 Disassemble the six retaining screwsand remove the motor access panelon the left hand side of machine.Then using the dowels as locators,bolt the carriage support (9, Fig. 1)to the base. Next assemble the twosupport braces (11, Fig. 1). Spacers(12, Fig. 1) are used on the lowerbolts, and nuts (with lock washers)are assembled on the inside of thebase.

B.3 Lower the upper blade pulley (7,Fig. 1) by giving the tension adjust-ment hand wheel (8, Fig. 1) a few

— 3 —

5216 INSTRUCTIONS

Fig. 2turns to the left. Open the head door(5, Fig. 1). Remove the blade coverassy. (4, Fig. 1). Raise the gage plate(1, Fig. 4) to its stopped position.Lower the upper guide unit (Fig. 2)to its lowest position. Place the sawblade over the upper blade pulley (7,Fig. 1) and lower blade pulley (3,Fig. 1). The blade teeth must pointto the right and downward whenviewed from the front as shown inFig. 3. If they do not point down-ward, remove the blade, twist insideout and replace it on the saw. Makesure the blade is properly placed inthe upper guide unit (Fig. 2).

Turn the tension adjusting handwheel (8, Fig. 1) to the right untilthe figure "3" starts to show in thetension indicator (2, Fig. 4). Givethe upper blade pulley a few turns byhand so that the blade centers itself

on the pulleys. Then turn the tensionadjusting hand wheel slowly to theright until the indicator registers ap-proximately "4" at eye level. Thisis the best operating tension for theblade.NOTE: See section "J" for adjust-ment of blade back-up blocks.

B.4 Assemble the rear wiper sub-assy. (7,Fig. 3). The spring catch (6, Fig. 3)will lock it in place. Wipers (8, Fig. 3)should be on both sides of blade.

B.5 Swing up bakelite guard (1, Fig. 3).Position front wiper assembly, withblade in slot of steel block (5, Fig. 3)and wipers (3, Fig. 3) on both sidesof blade. Align assembly into slot ofwiper bracket slideway and lower intoposition. Close bakelite guard (1,Fig. 3).

B.6 Close head door (5, Fig. 1) (a perma-nent magnet holds the door in a closedposition).

B.7 With the gage plate (1, Fig. 4) in itsraised position (to clear table area),assemble the table (5, Fig. 4). Standin front of the saw, raise the frontedge of the table slightly to clear thesaw blade. Move the table to its ap-proximate location so that the rightedge of the rear table notch is closeto the column. The rear table angle(6, Fig. 4) should be against and in-side of the rear table rest angle (7,Fig. 4) for front to rear location oftable. Lower the front edge of thetable. Next raise the left end of thetable approximately 15° and move

Fig. 3

INSTRUCTIONS 5216

'PL-SKI;

Fig. 4

the table to the right. This will en-gage the table cross rod with the tablecatch (Fig. 5) on the base. Lowertable into position, aligning frontnotch with front blade guide. Withthe table properly positioned, the re-inforcing angles of the table nest in-side the table rest angles of the base.Lock the table in place with the tableclamp (8, Fig. 4). Assemble and latchthe blade cover (4, Fig. 1).

B.8 The carriage may be assembled fromeither side. Turn the "L" shaped car-riage stop (Fig. 6) so that the rubberbumper is toward rear of machine.Align the center bearings of the car-riage with the carriage guide (11,Fig. 4). Roll carriage into place.Turn carriage stop (Fig. 6) into stop-ping position.

B.9 Assemble the switch pull rod and knobassembly (13, Fig. 4). Insert rodthrough hole in carriage support, thenthrough bushing in base. Removecotter pin from flat head pin (9,Fig. 4). Assemble pin (9, Fig. 4)through hole in switch rod and retainpin with cotter pin.

Switch Replacement: Switch shouldalways be assembled so that switchknob (13, Fig. 4) must be pulled tostart machine.

NOTE: Do not re-assemble accesspanel until electrical connections havebeen made.

C. WIRINGCHECK THE DATA ON THE NAME

PLATE (12, Fig. 4) TO MAKE SURETHAT IT AGREES WITH YOUR ELEC-TRICAL SUPPLY BEFORE CONNECT-ING TO THE POWER LINE.

A hole (10, Fig. 4) in the base is pro-vided for connecting rigid or flexible con-duit to the machine. Connect power leadsdirectly to switch. The motor leads arealready connected to the switch at thefactory.

Be sure to use wire large enough tomeet your local code requirements. Forproper performance use wire sizes of NOTLESS than #10 gage for 115 V., or #14gage for 230 V. on single phase models.Use #14 gage for 208, 220, and 440 V. onthree phase models. For long runs, be-tween power inlet and saw, use a largersize.

— 5 —

5216 INSTRUCTIONS

Fig. 5

D. SAFETY FEATURESThe Hobart saw is provided with safety

devices to give maximum protection to theoperator. Keep guards in place at alltimes.

D.I UPPER GUIDE ASSEMBLY (Fig. 2) :Keep as low as the size of the workpermits.

D.2 DOORS: Keep all doors closed whilemachine is running.

D.3 BUTT-END PUSHER (15, Fig. 4):Use the pusher plate as described insection "F.5" and it will be unneces-sary to hold your hand near the run-ning saw blade.

D.4 GAGE PLATE: The end of the gageplate (1, Fig. 4) is shaped to givemaximum support of the product be-ing cut and protection at this criticalpoint, and at the same time facilitateslice removal.

D.5 SWITCH KNOB (13, Fig. 4): Knobmust be pulled to start machine. Thiseliminates chance starting by acciden-tal bumping of knob.

F. OPERATIONF.I Place the item to be cut on the car-

riage and turn on the motor switchby pulling switch knob (13, Fig. 4).Stand in front of the machine, lean-ing lightly against the scalloped frontof the carriage, move the carriage tothe left, past the saw blade, at asteady and uniform rate. Your lefthand will then be free to take awayand stack the items as they are cutoff. Make it a habit to move yourhand around the left side, or back ofthe saw blade, when reaching for anitem — NEVER IN FRONT OF THETEETH. On the return stroke, pullthe item toward you so that it clearsthe saw blade.

F.2 If a locked carriage is desired; movethe carriage to the point where theright end of the carriage is in linewith the right end of the table. Thecarriage lock screw (14, Fig. 4) isthen in alignment with the hole incarriage guide. Tighten the lock screwand the carriage is locked in place.With the locked carriage the SAMESafety Procedure of reaching to theleft side (or back) of the saw bladewhen removing or stacking itemsshould ALWAYS be observed.

F.3 When cutting slices of uniform thick-ness, set the gage plate at the desiredposition, by turning the adjustingknob (1, Fig. 7). A scale is etchedon the table (5, Fig. 4). If the gageplate is not needed and interferes withthe work, it may be moved out of theway by either of the two followingmethods:

E. LUBRICATIONVery little lubrication is required, be-

cause all the high-speed shafts have eitherroller or ball bearings which are greasepacked and will operate a long time with-out attention.

E.I Keep a small amount of grease in thesix ball bearing rollers on the carriage.

E.2 Apply a few drops of oil frequentlyto the gage plate rack (4, Fig. 7)and work the gage plate assemblyback and forth a few times. (Seecleaning instructions).

E.3 For top operating efficiency have yourlocal Hobart service technician checkthis machine at least once a year. Fig. 6

•6 —

INSTRUCTIONS 5216

(a) Lift the adjusting knob (1,Fig. 7) (to disengage the teethof the rack (4, Fig. 7)) and slidethe gage plate to the rear of themachine.

(b) Raise the gage plate to a raisedposition (1, Fig. 4). In thisraised position, the gage platemay be slid to any location.

F.4 The adjustable gaging pin (3, Fig. 7)(after being set), permits the opera-tor to raise the adjusting knob (1,Fig. 7), slide the gage plate back outof the way, then return the gage plateto its original setting (turn knob (1,Fig. 7) clockwise to "snug-up" gageplate and make sure rack teeth areengaged). To set the gaging pin,loosen hand knob (2, Fig. 7) andslide pin against the support stop.Tighten hand knob.

F.5 Use the pusher plate (15, Fig. 4) tohold the meat against the gage platewhen slicing short ends. Dowels inthe pusher plate give the necessaryalignment with the rolled edge of thecarriage. A stop on this rolled edgeof the carriage prevents over-travel.By holding the pusher plate with yourright hand, your hand will then al-ways be a safe distance from the sawblade. Store the pusher plate on theunder side of the carriage support(10, Fig. 1) when not in use.

G. CLEANING & SANITIZINGThis saw has been designed for quick

and easy cleaning. It is IMPORTANTthat any machine used for the prepara-tion of food be kept in a clean and sanitarycondition. Daily cleaning is recommended.Make sure saw is turned "off" and stop-ped before starting cleaning operation.

PROCEDURE:

G.I Turn (at either end) the "L" shapedcarriage stop (Fig. 6) and roll offstainless steel carriage.

G.2 Rotate gage plate to raised position(1, Fig. 4).

G.3 Open and lift off blade cover (4,Fig. 1).

G.4 Release table clamp (8, Fig. 4) andremove stainless steel table.

G.5 Clean the gage plate rack (4, Fig. 7).

G.6 Turn hand knob (3, Fig. 4) a coupleof turns and bump with hand toloosen stud. Remove hand knob.Open and lift off head door (5,Fig. 1). Lift out upper pulley wiper(6, Fig. 1). Clean wiper. Do notreplace at this time.

G.7 Swing up bakelite guard (1, Fig. 3)and lift out front wiper assembly.Clean unit. Do not replace at thistime.

G.8 Press spring catch (6, Fig. 3) to re-lease, then remove rear wiper unit(7, Fig. 3). Clean unit.

G.9 Open, lift and remove base door (2,Fig. 1).

G.10 Turn tension adjusting hand wheel(4, Fig. 4) to the left to release bladetension. Remove saw blade and cleanin sink.

G.ll Remove hand knob (16, Fig. 4). Re-move upper guide unit (Fig. 2) (withblade already removed or tension re-leased on blade). Clean, lubricatewith TASTELESS oil. Do not re-place at this time.

G.12 Remove upper (7, Fig. 1) and lower(3, Fig. 1) blade pulleys by openinglatches (1, Fig. 8) clear of shafts andsliding pulleys from the shafts. Cleanpulleys in sink and lubricate borebefore replacing. NOTE: When re-placing pulleys, make sure the pulleylatches (1, Fig. 8) are properly seat-ed in grooves of shafts. (Upper andlower blade pulleys are interchange-able) .

G.13 All areas are now exposed for easyand thorough cleaning via one of thefollowing procedures:

G.13.1 HAND CLEANING:G.13.1.1 Materials required:

— 7 —

5216 INSTRUCTIONS

G.13.1.1.1 Small nylon bristledbrush with (approx.) 12"handle.

G.13.1.1.2 S m a l l plastic twocompartment pail.

G.13.1.1.3 Clean cloths.G.13.1.1.4 Cleaner ("Soilax" All

Purpose Cleaner).G.13.1.1.5 Sanitizer ( "Mikro-

Klene" iodophor sanitizer).G.13.1.1.6 Plastic spray bottle

(for sanitizer).G.13.1.2 Procedure (using "Soilax"

& "Mikro-Klene"):G.13.1.2.1 Add two ounces of

"Soilax" All Purpose Cleanerto a gallon of hot water inwash side of two compartmentpail.

G.13.1.2.2 Mix rinse solution byadding two teaspoons of "Mi-kro-Klene" in one gallon ofcool water in rinse side of pail.

G.13.1.2.3 B r u s h o u t l a r g escraps of soil and meat waste.

G.13.1.2.4 Begin cleaning in theupper pulley area. Brushthoroughly all surfaces beingsure to get in corners. Workyour way down, being sure todip the brush frequently intothe cleaning solution.

G.13.1.2.5 Similarly clean thetop area (which was coveredby the table and the carriage).Work down into the lowerpulley housing.

G.13.1.2.6 Remove the scrap panand wash separately in sink.Brush clean, the housing andthe area around the scrap pan.

G.13.1.2.7 R i n s i n g and sani-tizing can be done in one oftwo ways:(a) Go over all cleaned sur-faces with a cloth soaking wetwith "Mikro-Klene" rinse so-lution.(b) Rinse in fresh water andapply "Mikro-Klene" solutionvia of plastic spray bottle.

G.13.1.2.8 Allow all surfaces todrain dry and then re-assem-ble. Do not wipe dry.

G.13.1.2.9 Protect saw from re-contamination by covering.

G.13.1.2.10 R i n s e t h e nylonbrush thoroughly under run-ning water. Then dip thebrush in standard solution of"Mikro-Klene" and allow todrain dry in covered containeror wrapped in a freshly laun-dered towel. Cloth used for

rinsing should be sent to laun-dry, or discarded. Wash outpails.

G.13.2 HYDRAULIC CLEANING:G.13.2.1 Materials required (Eco-

nomics Laboratory System):G.13.2.1.1 Model E " M i k r o -

Spray" (Economics Labora-tory, Inc.).

G.13.2.1.2 "Mikro-Quat" deter-gent-sanitizer.

G.13.2.2 Procedure:G.13.2.2.1 Insert an eight ounce

bottle of "Mikro-Quat" intothe Model E "Mikro-Spray"and turn on the hot water.

G.13.2.2.2 Spray clean and sani-tize both pulley housings andthe table area. Be sure toget the hose stream into allcorners. Stubborn soil mayrequire a little brushing.

G.13.2.2.3 R i n s e with freshwater from another hose andallow to drain dry. Coverand store as in procedure6.18.1.

G.13.2.2.4 Either a floor drainor a wet vacuum pick-up ma-chine is required to dispose ofthe cleaning and rinsing solu-tions. It may also be desir-able to have a portable showercurtain type arrangement toprevent excess splashing intoother areas of the work space.

H. CHANGING SAW BLADESH.I Turn the left hand carriage stop (see

section G.I) and move the carriageto the left a few inches beyond thebakelite guard (1, Fig. 3).

H.2 Raise gage plate (1, Fig. 4) to raisedposition.

H.3 Turn tension adjusting hand wheel(4, Fig. 4) to left to release bladetension.

H.4 Remove blade cover assembly (4,Fig. 1).

H.5 Release table clamp (8, Fig. 4) andremove table.

H.6 Open head door (5, Fig. 1).

H.7 Swing up bakelite guard (1, Fig. 3).

H.8 Remove saw blade.

H.9 Assemble new blade. Make surefront and rear lower blade wipersare on both sides of blade.

— 8 —

INSTRUCTIONS 5216

Fig. 8

H.10 Turn the tension adjusting handwheel (4, Fig. 4) to the right untilthe edge of the "3" first appears inthe window (2, Fig. 4).

H.ll Turn the upper blade pulley (7,Fig. 1) by hand to center the blade.

H.12 Turn the tension adjusting handwheel to the right until the indicator(2, Fig. 4) registers "4" at eye level.

H.13 Close the lower bakelite guard (1,Fig. 3).

H.14 Re-assemble table and other dis-assembled parts.

J. ADJUSTMENT OF BLADE BACK-UPBLOCK

Special TUNGSTEN CARBIDE bladeback-up blocks take the cutting thrust.They are located at the back edge of the

saw blade, in the upper guide (1, Fig. 2)and the front lower wiper unit (4, Fig. 3).J.I Adjust the upper back-up block (1,

Fig. 2) by turning screw (2, Fig. 2).J.2 Adjust lower back-up block (4, Fig.

3) by turning screw (2, Fig. 3).

NOTE: Clearance between back-up blocksand blade should be approximately1/32" (with the saw runningwithout load). ALWAYS checkand adjust to this dimension afterchanging saw blades, as bladewidths may vary.

K. BLADE REPLACEMENTTwo saw blades are furnished as regular

equipment with each machine. Replace-ment blades are available through allHobart offices.

5216 REPLACEMENT PARTS

1-2

52!

BASE UNIT

REPLACEMENT PARTS 5216

BASE UNIT

ILLUS.PL-5916

123456789

1011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556

575859606162

PARTNO.

SC-36-50WL-4-2SC-20-19P-78917R-79124P-78917SC-13-65P-77192SC-10-33NS-31-14M-81339WS-18-8WL-4-4SC-62-43S-78062SC-78-36WL-4-4NS-13-25S-78993R-78040SC-8-9NS-9-22M-68176M-23274SC-8-9S-71518SC-62-42WL-4-4NS-13-25M-77217M-74888BV-3-42BV-5-11R-71418-1R-71418-2SC-47-32R-12430-62S-79471-1S-79472-1S-79471-2S-79472-2S-79472-3NS-13-25WL-4-4P-78992M-67305SC-36-71SC-46-98R-78043SD-9-19SC-10-33NS-31-14P-71437T-78038-1T-78038-2T-78038-3

T-78038-4SC-10-48WL-8-12M-68176S-71223SC-10-33

NAME OF PART

Fin. Bolt - 3/8"-16 x 1/2" Hex Hd.Lock Washer - 3/8" x .136" x .070"Mach. Screw - #10-32 x 3/4" Phil. Flat Hd.Bracket - HingeBlade Cover Assy.Bracket - HingeMach. Screw - * 10-32 x 3/4" Flat Hd.Clamp - Stationary TableMach. Screw - #10-24 x 1/2" Truss Hd.Stop Nut - #10-24 "Elastic"Dowel

AMT.

4212412222221222211111112224211111111111442

Booster - Motor As ReqdFin. Bolt - 3/8"-16 x 1-1/4" Hex Hd. 4Set Screw - #10-24 x 1/4" Slotted Hdls. Cup Pt. 4Panel - Motor Access 1Self-Tapping Screw - #10-32 x 5/16" Phil. Rd. Hd., Type F 6Mach. Screw - #10-24 x 1/2" Truss Hd. 4Stop Nut - #10-24 "Elastic" 4Clamp - Table 1Base Unit Assy, (all voltages except 115 V.) (Incls. items #6 & 7) 1Base Unit Assy. (115 V. only) (Incls. items #6 & 7) 1Base Unit Assy. (Mag. Starter) (All Voltages Except 115 V.) <Incls.

items #6 & 7) 1Base Unit Assy. (Mag. Starter) (115 V. Only) (Incls. items #6 & 7) __ 1Mach. Screw - #10-24 x 1/4" Truss Hd. 2Lock Washer - #10 Int. Shakeproof 2Clip - SpringCover - Column Top 1Mach. Screw - #10-24 x 1/2" Truss Hd. 5

WasherLock Washer - 3/8" x .136" x .070"Fin. Bolt - 3/8"-16 x 3/4" Hex Hd.Carriage Support Sub-Assy.Carriage Bolt - 3/8"-16 x 1"Lock Washer - 3/8" x .136" x .070"Full Nut - 3/8"-16 Hex Fin.Brace - Carriage SupportBase Door Sub-Assy.Mach. Screw - #10-24 x 3/8" Rd. Hd.Mach. Nut - #10-24 HexClip - SpringKnob - DoorMach. Screw - #10-24 x 3/8" Rd. Hd.Pan - ScrapFin. Bolt - 3/8"-16 x 1" Hex Hd.Lock Washer - 3/8" x .136" x .070"Full Nut - 3/8"-16 Hex Fin.Foot & Stud Assy.Washer - Shim"V" Belt (60 Cy.)"V" Belt (50 Cy.)"V" Pulley - Motor (5.6" O.D.) (60 Cy.) (Incls. item #36) _."V" Pulley - Motor (6.6" O.D.) (50 Cy.) (Incls. item #36) _.Set Screw - 5/16"-18 x 5/16" Soc. Hdls. Cup Pt.KeyMotor - 1 Phase, 115/208-230 V. 60 Cy. (Incls. item #37)Motor - 3 Phase, 208-220/440 V. 60 Cy. (Incls. item #37) _.Motor - 1 Phase, 110/220 V. 50 Cy. (Incls. item #37)Motor - 3 Phase, 208/416 V. 50 Cy. (Incls. item #37)Motor - 3 Phase, 220/380 V. 50 Cy. (Incls. item #37)Full Nut - 3/8"-16 Hex Fin.Lock Washer - 3/8" x .136" x .070"Reinforcement - Base _


HEAD UNIT


HEAD UNIT

ILLUS.PL-5200

123456789

1011121314151617181920212223242526272829303132333435363738394041424344454647484950515253

PARTNO.

SC-12-69P-67210M-67241SC-13-46BR-2-16RR-6-1R-71295NS-13-22WL-4-2RR-7-1BR-2-20P-67147P-67187WL-4-2NS-13-22M-75894WL-4-2NS-13-22P-75872-1SC-20-15P-78917M-79686M-20852M-20851R-72364S-75806P-71514M-77813-1R-71298P-75752M-75837SC-12-69P-75870M-71403SC-7-71WL-3-22P-67249P-75817SC-7-74WL-3-22P-71365PG-7-18P-79756P-75897RR-4-8SC-36-28WL-3-44BB-13-1P-75816M-20867M-75656SC-10-47R-75883R-75842

NAME OF PART

Mach. Screw - l/4"-20 x 1/2" Fil. Hd.Cap - BearingRetainer - BearingMach. Screw - #10-24 x 1/2" Flat Hd.Roller BearingRetaining RingCarrier - Upper BearingFull Nut - 3/8"-16 Hex Fin.Lock Washer - 3/8" x .136" x .070"Retaining RingRoller BearingCover Brkt. & Weld Nut Assy.Gib - Upper Brg. CarrierLock Washer - 3/8" x .136" x .070"Full Nut - 3/8"-16 Hex Fin.Stud - Upper Bearing Carrier SupportLock Washer - 3/8" x .136" x .070"Full Nut - 3/8"-16 Hex Fin.Head & Magnetic Catch Sub-Assy.Mach. Screw - #10-24 x 7/8" Phil. Flat Hd.Bracket - HingeCatch - Friction (#14-1/2 Frost)Latch .Screw - LatchFlanged Pulley (Blade) Sub-Assy. Unit (Incls. items #22, 23 & 24) __Door Assy. (Head)Blade - Meat Saw (128" Lg.)Groov-Pin - SpecialShaft - Upper Bearing CarrierShield - Bearing CarrierSpring - DetentMach. Screw - l/4"-20 x 1/2" Fil. Hd.Bearing Carrier Cap & Seal Sub-Assy. (Incls. item #34)Seal - GreaseMach. Screw - #10-24 x 1/4" Rd. Hd.Lock Washer - #10 x .055" x .040"Plate - Blade Tension SightBracket - Tension IndicatorMach. Screw - #10-24 x 3/8" Rd. Hd.Lock Washer - #10 x .055" x .040"Screw - Blade Tension AdjustingGroov-Pin - Type #5, 1/4" x 1"Wheel - HandNut - Blade Tension AdjustingRetaining RingFin. Bolt - 5/16"-18 x 1-1/4" Hex Hd.Lock Washer - 5/16" x .125" x .078"Thrust Bearing - Nice #603Indicator - TensionSpring - Adj. Blade TensionWindow Unit -Mach. Screw - #10-24 x 1-3/8" Truss Hd.Cover & Window Sub-Assy. (Incls. item #51)Upper Bearing Carrier Assy. (Incls. items #1, 2, 3, 4, 5, 6, 7, 10, 11, 29,

32 & 33) .

AMT.

3112111441122

•4444414211111111123112211221111144111121


25

26

ILLUS.PL-5163

12345

9101112131415161718192021222324252627282930

PARTNO.

NS-17-49WS-11-24SC-47-32R-74151KW-3-15SC-12-69M-79129P-67203BR-2-16RR-6-1NS-13-30WL-8-31R-71296R-79128WL-8-31RR-7-1NS-13-30BR-2-20M-71403M-77319M-77510M-77511M-77813-1R-72364WS-2-51SC-68-12M-79686M-20852M-20851SC-12-69P-79127

LOWER BEARING CARRIER UNIT

NAME OF PART

Jam Nut - 3/4"-16 Hex Fin.WasherSet Screw - 5/16"-18 x 5/16" Soc. Hdls. Cup Pt."V" Pulley - Brg. Carrier (13" O.D.) (Inels. item #3)Key - #807 WoodruffMach. Screw - l/4"-20 x 1/2" Fil. Hd.Conveyor - Lower Bearing Carrier GreaseCap - Loxver Brg. Carrier ("V" Belt Side)Roller BearingRetaining RingFull Nut - l/2"-13 Hex Fin.Lock Washer - 1/2" Int. ShakeproofCarrier - Lower BearingShaft - Lower Brg. CarrierLock Washer - 1/2" Int. ShakeproofRetaining RingFull Nut - l/2"-13 Hex Fin.Roller BearingSeal - GreaseBearing Cap & Seal Sub-Assy. (Incls. item #19)Washer & Seal Sub-Assy. (Incls. item #22)Seal - DiaphragmGroov-Pin - SpecialFlanged Pulley (Blade) Sub-Assy. Unit (Incls. items #27, 28 & 29) —WasherMach. Screw - #10-32 x 5/16" Trimmed Hex Hd.Catch - Friction (#14-1/2 Frost)LatchScrew - LatchMach. Screw - l/4"-20 x 1/2" Fil. Hd.Lower Bearing Carrier Sub-Assy. (Incls. items #6, 8, 9, 10, 13, 14, 16,

18, 20 & 30)

AMT.

211113111144114141111111441113


| PL-5166]

18'

GAGE PLATE UNIT

ILLUS.PL-5166

1234

91011121314151617181920212223242526

PARTNO.

SC-9-56WL-3-14P-77848M-77515SC-47-70M-83481WS-18-10M-77843PG-7-7M-20887M-78923M-78920M-77235P-77841-2R-80433SC-47-37SC-47-37SC-62-43WL-4-4WS-18-9M-82179PG-7-36M-79155R-77844-2M-77842R-77191S-77234-2P-77846

NAME OF PART

Mach. Screw - #8-32 x 3/8" Rd. Hd. .Lock Washer - #8 x .047" x .031" __.Spring - Gage PlateKnob .Set Screw - #10-32 x 3/8" Soc. Hdls. Cup Pt.Worm Bracket & Brg. Sub-Assy.WasherShaft - WormGroov-Pin - Type #5, 1/8" x 7/16"Worm _Knob & Stud Sub-Assy.SlugPin - Gage PlateRack - Gage PlateBracket - Gage Plate Support (Front)Set Screw - 5/16"-18 x 3/8" Soc. Hdls. Kn. Cup Pt.Set Screw - 5/16"-18 x 3/8" Soc. Hdls. Kn. Cup Pt.Fin. Bolt - 3/8"-16 x 3/4" Hex Hd.Lock Washer - 3/8" x .136" x .070"WasherGaging Pin Sub-Assy.Groov-Pin - Type #5, 7/64" x 7/16"Fin. Mach. BoltGage Plate & Bushing Sub-Assy.Rod - Gage Plate StopBracket - Gage Plate Support (Rear)Gage Plate Assy. (Incls. items #1 thru 13 inclusive and #21. 22, 23 & 24)Worm Bracket Sub-Assy. (Incls. items #1 thru 10 inclusive)

AMT.

1111111111111112244411111111

-15 —


TABLE, CARRIAGE AND TRACK UNIT

— 16 —


TABLE, CARRIAGE AND TRACK UNIT

ILLUS. PARTPL-5472 NO. NAME OF PART AMT.

1 P-77576-2 Pusher Plate Assy. 12 SC-10-48 Mach. Screw - #10-24 x 1/4" Truss Hd. 13 NS-27-3 Acorn Nut - # 10-24 14 S-79089 Carriage Sub-Assy. 15 R-78098 Carriage Guide Sub-Assy. 16 P-79094 Spacer - Carriage Guide 17 M-78935-1 Screw - Carriage Lock 18 NS-13-25 Full Nut - 3/8"-16 Hex Fin. 29 WLr4-4 Lock Washer - 3/8" x .136" x .070" 2

10 BB-8-3 Ball Bearing - Nice #400-24 211 WS-18-12 Washer (.010" thk.) As Reqd.12 M-80698 Shim - Washer (.005" thk.) As Reqd.13 WS-18-14 Washer (3/64" thk.) 214 NS-13-25 Full Nut - 3/8"-16 Hex Fin. 415 WL-4-4 Lock Washer - 3/8" x .136" x .070" 416 WS-18-5 Washer 417 BB-8-3 Ball Bearing - Nice #400-24 418 SC-37-73 Fin. Bolt - 3/8"-16 x 1" Hex Hd. 419 M-77311 Stop - Carriage 220 M-77318 Bumper - Carriage Stop 221 SC-78-35 Carriage Bolt - 5/16"-18 x 3/4" 222 WS-18-12 Washer 223 M-70087 Washer - Spring 224 NS-32-12 Stop Nut - 5/16"-18 "Flexloc" 225 NS-13-14 Full Nut - 5/16"-18 Hex Fin. 526 WL-3-47 Lock Washer - 5/16" x .125" x .078" 527 WS-17-16 Washer 528 SC-78-42 Carriage Bolt - 5/16"-18 x 1" 529 S-78055 Rest - Front Table 130 NS-13-25 Full Nut - 3/8"-16 Hex Fin. 631 WL-4-4 Lock Washer - 3/8" x .136" x .070" 632 WS-18-8 Washer 633 WS-18-8 Washer 634 SC-62-42 Fin. Bolt - 3/8"-16 x 1" Hex Hd. 635 S-78056 Rest - Rear Table 136 S-78049 Table Assy. 1

M-78093 Carriage Unit Assy. (Incls. items #2, 3, 4, 7, 8, 9, 10, 11, 12, 13, 14, 15,16, 17 & 18) _ 1


36 37

35 34 33 32 31 30 29 28 '27-26'

|PL-4482"|

UPPER GUIDE AND PULLEY WIPER UNIT

— 18-


UPPER GUIDE AND PULLEY WIPER UNIT

I L L U S .PL-4482

123456789

10111213141516171819202122232425262728293031323334353637

PARTNO.

SC-53-16M-69849P-75869-1M-75865M-75866M-75864SC-47-74SC-63-33PB-2-26P-71397-1SC-10-33V-21158M-67315R-71361V-23326M-23275M-23328M-71382M-71373M-71377SC-7-24M-67182SC-10-36WS-2-51M-71449-2P-71359SC-75-5M-71368SC-10-33P-75025R-67500-2M-71364P-71376R-67500-7M-67315M-71362M-67306M-71449-2P-71398-1

NAME OF PART

Mach. Screw - 5/16"-18 x 5/8" Truss Hd.Stop - Slide Rod .Rod - Upper Blade Guide SlideShoe - Slide RodSpring - Slide Rod AdjustingScrew - Slide Rod AdjustingSet Screw - #8-32 x 1/4" Soc. Hdls., Cup Pt.Set Screw - 3/8"-16 x 3/8" Hdls. Flat Pt.Plug ButtonGuard - Upper Guide BladeMach. Screw - #10-24 x 1/2" Truss Hd.Stud - Upper Guide SupportKnob _Support - Upper GuideSpring - Back-Up BlockLock Washer - Back-Up Block (Stat.)Lock Washer - Back-Up Block (Rot.)Shaft - Back-Up BlockBlock - Blade Back-UpRetainer - Blade Back-Up BlockMach. Screw - #6-32 x 3/8" Rd. Hd.Guide - BladeMach. Screw - #10-24 x 5/8" Truss Hd.Washer - Blade Guide SpacerShim - Upper Guide SupportBracket - Upper ScraperSet Screw - #10-24 x 1/4" Soc. Hdls., Kn. Cup Pt.Wiper - Blade PulleyMach. Screw - #10-24 x 1/2" Truss Hd.Bracket - Upper Pulley Wiper"O" RingSpring - Blade Pulley WiperShaft

P-75031-2

"O" RingKnobStud - Upper Wiper SupportPin - Table RestShim (Use with item #22)Upper Guide Unit Assy. (Incls. items #10, 11, 12, 14, 15, 16, 17, 18, 19,

20, 21, 22, 23, 24 & 25)Upper Pulley Wiper Assy. (Incls. items #26 thru 37 inclusive)

AMT.

111111111121111111112222

As Reqd111211111111

As Reqd.

11

-19 —


CD tO ^CT3 CO CO

58 S 2S

LOWER WIPERS AND GUIDE UNIT

— 20 —


LOWER WIPERS AND GUIDE UNIT

ILLUS.PL-4483

12345

9101112131415161718192021222324252627282930313233343536373839404142434445464748495051

PARTNO.

SC-12-81M-71369NS-9-23M-71363SC-60-72SC-10-33M-71368SC-75-5P-71358SC-63-21P-11800-244SC-12-42P-71372P-67189SC-37-85M-67702M-74612M-67185SC-21-85WL-6-1M-67184SC-21-14WL-6-1M-72443R-67500-2M-71364P-71376R-67500-7S-71360V-23326M-23275M-23328M-71382M-71373M-71377SC-7-24NS-31-19WS-3-45SC-41-1M-75304M-75307NS-11-12WL-6-1SC-21-92SC-21-91M-75310M-74612M-67184M-67185WLr-6-1

SC-21-85S-71378

P-75303

NAME OF PART AMT.

Mach. Screw - #10-24 x 1" Fil. Hd. 2Guide - Saw Blade 1Mach. Nut - #10-24 Hex 1Guard - Saw Blade 1Mach. Screw - #10-24 x 1-1/4" Rd. Hd. 1Mach. Screw - #10-24 x 1/2" Truss Hd. 2Wiper - Blade Pulley 1Set Screw - #10-24 x 1/4" Soc. Hdls., Kn. Cup Pt. 1Bracket - Scraper Pivot 1Set Screw - #10-24 x 5/16" Hdls. Flat Pt. 2Dowel 1Mach. Screw - l/4"-20 x 1/2" Fil. Hd. 3Slide - Lower Wiper Brkt. 1Slideway - Wiper Brkt. 1Fin. Bolt - 5/16"-18 x 1" Hex Hd. 2Plate - Wiper Brkt. Retainer 1Spring - Back-UpSpring - Blade Scraper 2Mach. Screw - #8-32 x 3/16" Rd. Hd. 4Lock Washer - #8 x .047" x .031" 4Scraper - Blade 2Mach. Screw - #8-32 x 3/8" Rd. Hd. 4Lock Washer - #8 x .047" x .031" 4Shield - Lower Pulley 1"O" Ring 1Spring - Blade Pulley Wiper 1Shaft - Lower Wiper Brkt. 1"O" Ring 1Bracket - Lower Wiper 1Spring - Back-Up Block 1Lock Washer - Back-Up Block (Stat.) 1Lock Washer - Back-Up Block (Rot.) 1Shaft - Back-Up Block 1Block - Blade Back-Up 1Retainer - Blade Back-Up Block 1Mach. Screw - #6-32 x 3/8" Rd. Hd. 2Stop Nut - l/4"-20 "Elastic"Washer 4Fin. Bolt - l/4"-20 x 3/4" Hex Hd. 2Rear Wiper Brkt. & Slide Stud Sub-Assy.Stop Spring & Rear Wiper Slide Sub-Assy. 1Mach. Nut - #8-32 Hex 4Lock Washer - #8 x .047" x .031" 4Mach. Screw - #8-32 x 7/16" Rd. Hd. 2Mach. Screw - #8-32 x 5/16" Rd. Hd. 2Support - Rear Wiper Scraper 1Spring - Back-Up 2Scraper - Blade 2Spring - Scraper Blade 2Lock Washer - #8 x .047" x .031" 4Mach. Screw - #8-32 x 3/16" Rd. Hd. 4Lower Wiper & Guide Unit Assy. (Incls. items #1 thru 13 inclusive &

items #17 thru 36 inclusive) 1Rear Wiper Sub-Assy. (Incls. items #40 thru 51 inclusive) 1


10

11

13

29

32 33

37

|PL-59I7|

SWITCH UNIT

— 22 —


SWITCH UNIT

ILLUS.PL-5917

PARTNO. NAME OF PART AMT.

1 P-78902 Bracket - Switch Mounting 12 M-78901 Yoke Guide & Track Assy. 13 M-60365 Yoke - Switch Operating 14 M-74835 Screw - Switch Mounting 25 M-78091 Rod - Switch 16 PC-3-16 Cotter Pin - 1/16" x 3/8" 17 M-78837 Pin - Flat Hd. 28 PC-3-16 Cotter Pin - 1/16" x 3/8" 29 M-78832 Lever - Pivot 1

10 ' M-78833-3 Rod - Switch (Upper) 111 M-80540 Speed Nut 112 M-80538 Bushing 113 M-78940 Knob 114 M-74835 Screw - Switch Mounting 215 R-24940-4 Switch (1 Ph., below 250 V.) 116 R-24940-2 Switch (2 & 3 Ph., below 250 V.) 117 SS-3-26 Switch (2 & 3 Ph., above 250 V.) 118 P-62479 Starter - Manual (Single Phase) (Less Elements) (Give Elec. Spec. &

Mach. Model) 119 P-61917 Starter - Manual (Three Phase) (Less Elements) (Give Elec Spec. &

Mach. Model) 120 * Thermal Element - Manual Starter (Give Elec. Spec. & Mach. Model) _-AsReqd.21 M-70262 Insulator - Starter (Use with Manual Starter P-61917) 122 WS-2-51 Washer 223 WL-3-20 Lock Washer - #10 x .055" x .040" 224 SC-8-9 Mach. Screw - #10-24 x 3/8" Rd. Hd. 2

MAGNETIC STARTER25 NS-9-22 Mach. Nut - #10-24 Hex 326 WL-3-20 Lock Washer - #10 x .055" x .040" 327 M-78752-4 Clamp 328 WS-3-45 Washer (7/8" O.D.) 229 WS-2-51 Washer (1/2" O.D.) 230 SC-9-25 Mach. Screw - #10-24 x 5/8" Rd. Hd. 331 P-78092 Mounting Bracket Sub-Assy. 132 NS-13-2 Full Nut - l/4"-20 Hex Fin. 133 WL-3-38 Lock Washer - 1/4" x .109" x .062" 134 SC-9-42 Mach. Screw - l/4"-20 x 5/8" Rd. Hd. 135 R-78558 Station - Push Button 136 SC-37-87 Fin. Bolt - l/4"-20 x 1" Hex Hd. 237 FE-6-37 Ell - 90° Short (1/2" Male Thd. x 1/2" Thinwall) 138 P-67572-38 Conduit - 1/2" x 6-1/2" (Thinwall) 139 FE-6-45 Connector - Straight (1/2" Male Thd. x 1/2" Thinwall) 140 WL-3-38 Lock Washer - 1/4" x .109" x .062" 241 NS-13-2 Full Nut - l/4"-20 Hex Fin. 242 R-78166 Bracket - Starter Mounting 143 P-69917-1 Starter - Magnetic (1 Ph., 208/220 V.) (Less Elements) (Give Elec. Spec.

& Mach. Model) 144 P-69478 Starter - Magnetic (3 Ph., below 250 V.) (Less Elements) (Give Elec.

Spec. & Mach. Model) 145 P-69757 Starter - Magnetic (3 Ph., above 250 V.) (Less Elements) (Give Elec.

Spec. & Mach. Model) 146 * Thermal Element - Magnetic Starter (Give Elec. Spec. & Mach. Model) _As Reqd47 SC-8-9 Mach. Screw - #10-24 x 3/8" Rd. Hd.48 WL-3-20 Lock Washer - #10 x .055" x .040" !_—49 NS-9-22 Mach. Nut - #10-24 Hex 350 SC-9-56 Mach. Screw - #8-32 x 3/8" Rd. Hd. 351 WL-7-7 Lock Washer - #8 Ext. Shakeproof

* Hobart service technician to use Starter Element Part No. as listedon Starter Parts Sheet.

— 23 —

5216 INSTALLATION

ENLARGED VIEW OF LEGSHOWING ADJUSTING FOOT

MACHINE IS PART I ALLY DISASSEMBLEDFOR SHIPMENT. CRATED MACHINE WILLPASS THRU A 33"OPENING.

HOLE "A"LOCATED ASSHOWNON OPPOSITE SIDEOF BASE FOR CABLEOUTLET

HOLE "A" USE7/8"DlA.1-I/I6"DIA.

ALL VOLTAGES (EXCEPT II5V.)II5V.

*THEJ5E_ DIMENSJONS MAY INCREASE AS MUCHAS 1/2" DEPENDING ON LEG ADJUSTMENT

R-79778

INSTALLATION DIAGRAM

FORM 4276-B NOV. 1964 PRINTED IN U. S. A,

Documents

Hobart model 5216 Meat Saw