HMD927 SERIES POWER FEED MAGNETIC DRILL · OM9270717BEF Printed in U.S.A. 11/2018 operator’s manual HMD927 SERIES POWER FEED MAGNETIC DRILL Covers Drill Part Numbers: 0927202 0927204

OM9270717BEF Printed in U.S.A. 11/2018

operator’s manualHMD927 SERIES POWER FEED MAGNETIC DRILL

Covers Drill Part Numbers:

Covers Drill Part Numbers:

0927202 0927204

0927302 0927304

0927402 0927404

The HMD927 is offered in many versions. Refer to the Serial/Part number Label on your housing to direct you to the correct breakdown.

Part NumberCovers All 230V HMD927 Models

2

Control Panel Breakdown 10Motor Slide Assembly Breakdown 11Motor Breakdown 12Maintenance 13Adjustment of Gibs & Arbor Adjustment 13Swivel Base Instructions 14Arbor Removal & Installation 14Hints & Remedies for Holemaking 15Commercial / Industrial Limited Warranty 16Authorized Warranty Repair Centers 16

Welcome to HougenCongratulations on your purchase of the Hougen® Portable Magnetic Drill. Your model is designed to produce superior holes quickly and efficiently. Through constant innovation and development, Hougen is committed to provide you with hole producing tools and products to help you be more productive.

Before attempting to operate your new Portable Magnetic Drill, please read all instructions first. These include the Operator’s Manual and Warning Label on the unit itself. With proper use, care, and maintenance, your model will provide you with years of effective hole drilling performance. Once again, thank you for selecting our product and welcome to Hougen.

Welcome to Hougen 2Safety Instructions 3-4Safety Chain Instructions 4Operation of Controls 5Safety Switch Indicator Light 5Pilot Light Switch 5Installing Hougen Cutters 6Operating Instructions 6Coolant Bottle Assembly & Breakdown 7HMD927 Assembly Breakdown 8-9

Specifications

UNPACKING YOUR NEW MAGNETIC DRILL1. Open shipping carton and remove the literature and hardware packages.2. Read and Follow All Instructions before attempting to operate your new Magnetic Drill.3. Complete and mail the Product Registration Card now. It is important that Hougen Manufacturing, Inc. have a record of product ownership.4. Open hardware package and check contents. 10565 1/8" Hex wrench for Gib Adjustment 04558 Feed handles (3) 04532 Feed handle knobs (3) 10730 Safety chain 24166 T-Handle Hex Key Wrench 13013 5/32" Allen wrench5. Using the handle of Magnetic Drill, lift unit out of the shipping case.

6. Remove all packing and securing material from the drill unit. 7. Screw the three Knobs into the three Feed Handles and then screw Handles into the Hub Assembly. Do not over tighten or may strip the knobs.8. Your Magnetic Drill was factory adjusted prior to shipping. Check to make sure that all gib adjustment screws, motor mount screws, front support bracket screws, and magnet mounting screws are snug and have not vibrated loose in transit.9. Your new Magnetic Drill comes complete with arbor mounted. The 3/4" diameter arbor bore fits all 3/4"-shank "12,000-Series" Hougen Cutters.

Reread Safety Warnings listed in the Operator’s Manual and on the drill unit to avoid injury. Follow operating procedures.

INDEX

Serial Number/Part Number Label

HOUGEN® PORTABLE MAGNETIC DRILLmoDel HmD927 poWerFeeD serIes

Cutter Type....................... Hougen "12,000-Series"Hole Capacity....................7/16" to 1-5/8" (12mm-41mm) Depth of Cut......................2" (50mm)Motor.................................250 and 450 RPM, 4.5A (230V)Swivel Area.......................1-1/8" W x 1-3/8" LNet Weight........................ 43 lbs. (19.5kg) Swivel Base: 46 lbs. (25.4 kg)

3

english

3

WARNING

IMPORTANT SAFETY INSTRUCTIONS

1. Work area safetya) Keep your work area clean and well lit. Cluttered or

dark areas invite accidents.b) Do not operate power tools in explosive atmospheres, such as in the presence of fl ammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. electrical safetya) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodifiedplugsand matching outlets will reduce risk of electrical shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.c) Don’t expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.d) Do not abuse the cord. Never use the cord for carrying or unpluggin the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an outdoor extension cord suitable for outdoor use. Use of cord suitable for outdoor use reduces the risk of

electric shock.f) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. personal safetya) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not

use a power tool while you are tired or under the infl uence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

Important Safety Instructions

Work Area

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to loose control.

Electrical Safety

Grounded tools must be plugged into an outlet properly in-stalled and grounded in accordance with all codes and ordi-anaces. Never remove the ground prong or modify the plug in any way. Do not us any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is prop-erly grounded. If the tools should electrically malfunction or break-down, grounding is provides a low resistance path to carry electricity away from the user.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

Don’t expose power tools to rain or wet conditions. Water enter-ing a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of eletric shock.

When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”; These cords are rated for outdoor use and reduce the risk of electrical shock.

Personal Safety

Stay alert, watch what you are doing and use common sense when using a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inat-tention while operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.

Avoid accidental starting. Be sure switchis off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unex-pected situations.

Use safety equipment. Always wear eye production. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Always use safety chain. Mounting can release.

Tool Use and Care

Use clamps or other practical way to secure and support the work piece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of start-ing the tool accidentally.

Store idle tools out of reach of childern and other untrained persons. Tools are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, break-age of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manu-facturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

Service

Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maitenance Instructions may create a risk of electric shock or injury.

WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electrical shock, fire and/or serious personal injury.

english

c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your fingerontheswitchorenergizingpowertoolsthat

have the switch on invites accidents.d) Remove any adjusting keys or wrench before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury.e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.f) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair

can be caught in moving parts.g) If devices are provided for the connection of dust extraction and collection facilities, ensure

these are conneted and properly used. Use of dustcollectioncanreducedust-relatedhazards.f) Do not let familiarity gained from frequent use of tools allow you to become complacent and

ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.g) Always use safety chain. Mounting can release.

4. power tool use and Carea) Do not force the power tool. Use the correct power tool for your application. The correct power

tool will do the job better and safer at the rate for which it is designed.b) Do not use the power tool if the switch does not turn it on or off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories or storing

power tools. Such preventative safety measures reduce the risk of starting the tool accidently.

(Continued on page 4)

Save all warnings and instructions for future reference.

Always wear eye protection while using cutting tools, or in the vicinity of cutting.

The slug is ejected at the end of the cut. Do not aim cutter or arbor so that ejected slug may hit someone around, or below you.

To prevent electric shock, do not use power tools near wet areas, or where power tool may become wet.

Do not stare at operating light.

Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool.Failuretofollowallinstructionslistedbelowmayresultinelectricshock,fireand/or serious injury.

WarnInG:

Cutters are sharp. Wear gloves when installing or removing cutter from arbor. Do not grab a rotating cutter.

4

IMPORTANT SAFETY INSTRUCTIONS

SAFETY CHAIN INSTRUCTIONS

outdoor extension Cord useWhen tool is used outdoors, use only extension cords intended for use outdoors and so marked.

additional safety precautionsArbor and cutter should never be used as a handhold or handle.Keep hands and clothing away from all moving parts. Do not use Hougen Cutters where ejected slug might cause injury (slug ejected at end of cut). Also, adhere to all operating instructions. Do not drill through any surface that may contain live electrical wiring. Drilling into a live wire could cause exposed metal parts of the drill to be made live. Remove chips wrapped around cutter and arbor after each hole. With motor off and power disconnected, grasp chips with leather gloved hand or pliers and pull while rotatingcounterclockwise. Should the cutter become jammed in the work, stop the unit immediately to prevent personal injury. Disconnect the drill from the power supply and loosen jammed cutter by turning the arbor counterclockwise. Never attempt to free the jammed cutter by starting the motor. Service at authorized repair center only.

operating near Welding equipmentDO NOT operate this unit on the same work surface that welding is being performed on. Severe damage to the unit, particularly the power cord, could occur. This could alsoresult in personal injury to the operator.

Circuit Breaker (If applicable)Changing of the circuit breaker to a higher amp ratedbreaker, or bypassing the circuit breaker is notrecommended and will void product warranty.

Circuit Breaker operation (If applicable) The circuit breaker is a thermal breaker. When it reaches the higher temperature rating it will trip and cause the unit to shut down. This is a protective device and can be reset after 5 to 10 minutes. To reset the breaker, press the breakerbutton back in. If it does not reset, let the unit cool a littlelonger until you can push the button in and it stays in position.

Save all warnings and instructions for future reference.

LENGTHOF CORD,

FEET

RECOMMENDEDWIRE GAUGE

RECOMMENDEDWIRE GAUGE

115V MOTOR10 - 12 AMPS

230V MOTOR5 - 6 AMPS

Up to 25 16 18

26 - 50 14 18

51 - 100 10 16

101 - 200 8 14

201 - 300 6 12

301 - 500 4 10

d) Store idle power tools out of reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Proper maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.g) Use the power tool, accessories and tool bits etc.

in accordance with the instructions, taking into account the working conditions and the work to be performed. Use of the power till for operations differentfromthoseintendedcouldresultinahazard-

ous situation.h) Keep handles and grasping surfaces, clean and

free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5. servicea) Have your power tool serviced by a qualified repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

safe electrical ConnectionYour Drill is rated for use on 115VAC or 230V at 50-60Hz. Do not attempt to use drill on power sources rated other than this.

plugs and receptacles .

Wet electrical connections are shock hazards.To prevent the cutting fluid from traveling along the cord and contacting the plug or power outlet,tie a drip loop as shown. Also elevate extensioncords or gang box connections.

extension CordsUse only 3-wire extension cords that have a 3-prong grounding type plug and 3-pole receptacles that accept the tool’s plug. Replace or repair damaged cords. Make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage.

Safe Electrical Connection Your Mag Drill is rated for use on 115VAC or 230V at 50-60Hz. Do not attempt to use drill on power sources rated other than this.

Extension Cords Use only 3-wire extension cords that have 3-prong grounding type plugs and 3-pole receptacles that accept the tool’s plug. Replace or repair damaged cords. Make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage.

Outdoor Use Extension Cords When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

Additional Safety Precautions Arbor and cutter should never be used as a handhold. Keep hands and clothing away from all moving parts. Do not use Hougen Cutters where ejected slug might cause injury (slug ejected at end of cut). Also, adhere to all operating instructions. Do not drill through any surface that may contain live electrical wiring. Drilling into a live wire could cause exposed

metal parts of the drill to be made live. Remove chips wrapped around Cutter and arbor after each hole. With motor off and power disconnected, grasp chips with leather gloved hand or pliers and pull while rotating counterclockwise. Should the cutter become jammed in the work, stop the unit immediately to prevent personal injury. Disconnect the drill from the power supply and loosen jammed cutter by turning the arbor counterclockwise. Never attempt to free the jammed cutter by starting the motor. Service at authorized repair center only.

Extension Cord Table

Plugs and Receptacles

HTGNEL,DROCFO

TEEF

DEDNEMMOCERERIWEGUAG


ROTOMV511SPMA21-01

ROTOMV032SPMA6-5

52OTPU 61 81

05-62 41 81

001-15 01 61

002-101 8 41

003-102 6 21

005-103 4 01

I

Operating Near Welding EquipmentDO NOT operate this unit on the same work surface that welding is being performed on. Severe damage to the unit, particularly the power cord, could occur. This could also result in personal injury to the operator.

Circuit Breaker (If Applicable)Changing of the circuit breaker to a higher amp rated breaker, orbypassing the circuit breaker is not recommended and will void

product warranty.

Circuit Breaker Operation (If Applicable)The circuit breaker is a thermal breaker. When it reaches the higher temperature rating it will trip and cause the unit to shut down. This is a protective device and can be reset after 5 to 10. To reset the breaker, press the breaker button back in. If it does not reset, let the unit cool a little longer until you can push the button in and it stays in position.

Save these Instructions.

Important Safety Instructions - ContinuedWARNING: Read and understand all instructions. Failure to follow all instructions listed below,

may result in electrical shock, fire and/or serious personal injury.

Typical USA 120v Typical USA 230v

230v Type Plug

Wet electrical connections are shock hazards. To prevent the cutting fluid from traveling along the cord and contacting the plug or power outlet, tie a drip loop as shown. Also elevate extension cords or gang box connections.








HTGNEL,DROCFO

TEEF



ROTOMV511SPMA21-01

ROTOMV032SPMA6-5

52OTPU 61 81

05-62 41 81

001-15 01 61

002-101 8 41

003-102 6 21

005-103 4 01

I



product warranty.






230v Type Plug









HTGNEL,DROCFO

TEEF



ROTOMV511SPMA21-01

ROTOMV032SPMA6-5

52OTPU 61 81

05-62 41 81

001-15 01 61

002-101 8 41

003-102 6 21

005-103 4 01

I



product warranty.






230v Type Plug


Typical USA 115V Typical USA 230V 230V Type I Plug

ADDITIONAL SAFETY INSTRUCTIONS

A safety chain should alWaYs be used whenever operating the drill. The safety chain prevents the drill unit from falling, in the event of a power failure or if the magnet breaks loose from the work surface. The safety chain attaches to the drill by running the chain thru the D-Ring on the back of the unit and then continuing around the material and/or work surface. Adjust the chain so it is tight and secure. Please refer to the diagram.

5

english

Power Feed Magnetic Drill

IMPORTANT: Before turning on the machine, it is important that the operator understands the interrelated functions of the SAFETY SWITCH, MAGNET SWITCH, AND MOTOR SWITCHES. READ SAFETY SWITCH INDICATOR LIGHT INSTRUCTIONS.

SAFETY SWITCH — Located in base of drill. Enables motor operation only whenmagnet is properly seated on a clean and flat work surface. Turns motor off if switch detects lift of unit.MAGNET ON/OFF SWITCH — Energizes and De-energizes the magnetic baseand activates the safety switch. Motor can now be started by pushing the motor START switch. MOTOR START/STOP SWITCHES — Starts and stops the motor

CONTROL PANEL SWITCH PLATE

1. Place Magnetic Drill on clean, flat steel plate that is at least 3/8" thick. 2. Plug unit into proper AC power source. DO NOT use with DC Power. 3. Locate the Magnet ON and OFF switch and the motor STOP and START switch. 4. NOTE: A loss of power will de-energize the magnetic base and deactivate the motor. When power is restored, the magnet will reenergize, however, the motor START switch must be depressed before the motor will start.

OPERATION OF CONTROLS BEFORE INSTALLING HOUGEN CUTTER

PILOT LIGHT SWITCH

CONTROL PANEL SWITCH PLATE

The Pilot Light is a Standard Feature onHougen portable magnetic drills. Its purpose is to illuminate the work surface area for easier viewing of pilot.

• To turn light ON, push the toggle switch up. • To turn light OFF, push the toggle switch down.

PILOT LIGHT


* Patent Pending

250 rpm1-1/16" - 1-5/8" Dia. (26mm - 41mm)

HMD927 RECOMMENDED RPM’S 450 rpm

7/16" - 1" Dia. (12mm - 25mm) RPM recommendations are based on using your HMD927 drill with Hougen "12,000-Series" H.S.S. Cutters. The RPM’s do notrepresent optimum speeds for any given cutter diameter and application. For more information refer to Hougen’s Speed & Feed Calculator located on Hougen.com, or call 1-800-426-7818 for Technical Support.

Material must be a least 3/8" thick. Material thinner than 3/8" will cause a "weak" magnet condition. HOUGEN MANUFACTURING RECOMMENDS THAT CONDITIONS ARE CORRECTED SO LIGHT IS GREEN.

THIS ALLOWS FOR THE UNIT TO BE OPERATED IN A SAFE MANNER.For any questions please contact Hougen Manufacturing’s Technical Service at (810) 635-7111.

The Safety Switch Indicator Light is a Standard Safety Feature on Hougen portable magnetic drills. Its purpose is to inform the user that the lift detector switch is activated.

If light is Green:In normal operation the safety switch light will be green. Motor "On" and "Off" Switchesfunction normally.

If light is Red:A condition with the safety switch exists that needs to be corrected. Possible causes: • Safety Switch is defective. Have drill serviced. • Uneven work surface or material. Check work surface for flatness. • Dirt or chips under magnet. Clean work surface.

Testing Safety Switch:Before operating the drill always test the safety switch. To test switch...place drill on work surface and plug into the outlet.Rock drill so magnet lifts off work surface. Safety Switch Light should change from green to red. If light stays green or red,a problem exists with the safety switch that must be corrected. (ie...safety switch defective, safety plunger in the base of magnet is stuck in position, etc.) Please correct and retest before operating drill.

SAFETY SWITCH INDICATOR LIGHT** SAFETY SWITCH LIGHT WILL COME ON AND REMAIN ON WHILE DRILL IS PLUGGED IN **

6

OPERATING INSTRUCTIONSAlways remember that the magnet’s holding power is directly related to the workpiece thickness and surface condition. Since magnetic attraction diminishes with thinner material or rough surfaces, mechanical clamping of drill unit to the workpiece should be used when cutting thin material (3/8" or less) or material with uneven surfaces.

POWER FEED MODE

Manual Feed

Power Feed Engagement Handle

Step 5 Step 8

Power Feed

1. Make sure workpiece and bottom of magnet are free of chips, oil, etc.2. Position drill by sliding it and gently feeding Arbor so that pilot point is touching center of hole to be drilled.3. Secure unit to workpiece with safety chain.4. Turn magnet "ON" by pressing the magnet ON switch.5. On Control Panel Flip Power/Manual Feed Switch to Power Feed.6. Turn on Cutting Fluid and check for proper fl ow by slightly depressing.7. Make certain that cutter is clear of workpiece by 1/16" - 1/8" and turn motor "ON" by pressing the motor START switch.8. In center of feed handles Flip Power Feed Handle out to engage Power Feed Motor. The unit will feed itself into and through the workpiece.9. At conclusion of cut, motor will automatically turn OFF. CAUTION: Slug can eject with force and distance. Disengage Power Feed Handle then turn Feed Handles to raise Arbor and make sure slug has fallen free.11. Turn magnet "OFF" by pressing the magnet OFF switch. 12. Disconnect from power source.13. If necessary, remove chips from cutter and magnet, preferably wearing leather work gloves and/or with pliers. Disconnect safety chain and you are ready to move unit to new drilling position.

MANUAL FEED MODE 1. Make sure workpiece and bottom of magnet are free of chips, oil, etc.2. Position drill by sliding it and gently feeding Arbor so that pilot point is touching center of hole to be drilled.3. Secure unit to workpiece with safety chain.4. Turn magnet "ON" by pressing the magnet ON switch.5. On Control Panel Flip Power/Manual Feed Switch to Manual Feed.6. Turn Feed Handle, raising the cutter until the pilot is above the work surface.7. Fill coolant reservoir or fi ll attached coolant bottle if applicable.8. Make certain that cutter is clear of workpiece and turn motor "ON" by pressing the motor START switch.9. Feed Hougen Cutter slowly into workpiece. Only after cutting path is established to a depth of about 1/16" can full force be applied to feed handles.10. Ease up on feed pressure as cutter starts breaking through.11. At conclusion of cut, turn motor "OFF" by pressing motor STOP switch. Turn Feed Handles to raise Arbor thereby ejecting the slug if it hasn’t already fallen free.12. Turn magnet "OFF" by pressing the magnet OFF switch. 13. Disconnect from power source.14. If necessary, remove chips from cutter and magnet, preferably wearing leather work gloves and/or with pliers. Disconnect safety chain and you are ready to move unit to new drilling position.

When drilling, especially in horizontal or overhead positions, always apply feed pressure toward the work surface. Never pull away from the work surface as this can weaken magnetic holding power.

Use handlesto feed towardwork surface

Never pullhandles away

from work surface.

7

english

07950 Coolant Bottle AssemblyPart # Description08255 Round Bottle

08061 Coolant Botttle Bracket (Bottle to Bracket)

41044 SCR-BHC 10-32 x 3/8

05065 Ball Valve

05067 Brass Barb Fitting (bottom of the bottle)

40304 Vinyl Tube

24124 Cap - Coolant Bottle

COOLANT BOTTLE ASSEMBLY

INSTALLING HOUGEN CUTTER IN ARBOR

1. With Magnetic Drill in operating position, turn the feed handles so that cutter and pilot are above the work surface.

2. With magnet turned ON & motor OFF, fill reservoir by introducing cutting fluid through slots in Arbor. Cutting fluid should not leak out.3. Test metering capabilities of Arbor/Cutter/Pilot assembly (magnet ON - motor OFF) feeding the Arbor gently toward work surface until pilot is pushed up into Cutter, thus allowing fluid to filter down onto work surface through groove in pilot.4. For proper lubrication, all fluid in reservoir should empty onto work surface in no less than 15 seconds and no longer than 30 seconds.5. Reservoir holds enough coolant for cutting approximately one hole. * This method of using coolant can also be used for an attached coolant bottle if the bottle is lost.6. For horizontal or drilling overhead holes, use Slick-Stik Lubricant.

OPERATION OF CUTTING FLUID RESERVOIR

CoolantReservoir

Set Screwsgo here

"12000-Series" Hougen Cutter

Pilot

AddCoolant

Here

Slide Vinyl Tube overthe Brass Barb Fitting

AttachCoolantBottle

CoolantFlow On / Off

1. Disconnect from power source and remove T-Handle wrench from holder at top of drill.2. Lay drill on its side with feed handles up or be sure Arbor clears table if unit is in normal operating position.3. Turn Feed Handles until cutter mounting set screws are exposed and completely remove the set screws.4. Insert proper pilot in shank end of Hougen Cutter.5. Insert Hougen Cutter until flat on cutter shank is aligned with set screw holes and is exactly perpendicular to axis of set screw holes. 6. Insert set screws and tighten. Check to be certain that cutter is secure.

Set Screwsgo here

"12000-Series" Hougen Cutter

Pilot

Wrench Holder

8

HMD927 MAG BASE DRILL

70

78

76

77

75

74

72

71

73

79

#51 - Coolant Arbor Assembly

FRONT SUPPORT BRACKET ASSEMBLY

0787017

COOLANT INDUCER ASM0707616WASHER-THRUST 1-3/8 X 2-1/16 X 1/32

4030125

ARBOR ASM0786914RING-RETAINING 1-9/16" SHAFT DIA.

4039813

WASHER-THRUST 40mm X 60mm X 1mm

4023422

RING-RETAINER FOR 1-3/8 SHAFT4030221DESCRIPTIONPART NO.QTYITEM

A60

57

54

59

58

61

63

62

56

55

67

68

69

68

64

65

66

65

64

FRONT SUPPORT BRACKET ASSEMBLY

0787017

COOLANT INDUCER ASM0707616WASHER-THRUST 1-3/8 X 2-1/16 X 1/32

4030125

ARBOR ASM0786914RING-RETAINING 1-9/16" SHAFT DIA.

4039813

WASHER-THRUST 40mm X 60mm X 1mm

4023422

RING-RETAINER FOR 1-3/8 SHAFT4030221DESCRIPTIONPART NO.QTYITEM

A

Motor/Slide Assembly

(see page 11)

Control PanelAssembly

(see page 10)

MotorAssembly

(see page 12)

CoolantBottle Assembly

(see page 7)

2

1

6

3

4

5

7

89 10

1112

8

13

14

15

816

1718

19

20

21

22

2324

25

2627

53

2930

31

3233

34

35

36

38

40

41

42

45

46

47

48

49

50

51

52

53

28

Swivel Base Assembly

(see page 11)

9

1208013 Magnet Assembly

Item Part # Description Qty70 08014 Magnet Assembly 171 04910 Plunger Assembly 172 10971 SCR SHC 1/4-20 x 1/2" LG 273 10972 SCR BHC #6-32 x 7/8" LG 274 17271 Spring - Taper, Comp. 175 04885 Microswitch Assy. 176 07887 Plate - Ring Retaining 177 24144 D-Ring 178 41046 SCR SHC #10-32 x 1/2" LG 479 04909 Bracket - Safety Switch 1

HMD927 BreakdownItem Part # Description Qty

1 08140 Motor / Slide Assy. 12 07950 Coolant Bottle Assy. 13 10559 SCR BHC #10-32 x 1-1/4 LG 14 07833 Stop Block 15 08159 Drill Housing Assembly 16 19571 Power Cord Assembly 17 19024 Engagement Label 18 01165 Retaining Ring 39 19005 Drive Clutch 410 19008 Gear Spur Removable #2 111 08643 Shaft - Spline 112 10836 Retaining Ring 113 19030 Feed Hub Assembly 114 05115 Washer - Flat .505 x .75 x .03 115 05114 Spring - Comp 116 19010 Plate - Hub Engagement 117 90077 SCR BHC #10-32 x 1/2 LG 318 08642 Handle - Lever 119 02902 Pin - Roll 1/2 x 5/8 120 40277 Pin - Dowel 3/16 x 5/8 121 04558 Feed Handle 322 04532 Knob - Oval 323 19020 Spacer 424 19017 Shaft - 20 Tooth Gear 225 19016 Gear Spur Removable #1 226 41044 SCR BHC #10-32 x 3/8 LG 427 08142 Control Panel Assembly 128 40237 Gib Screws 529 40077 SCR SHC 1/4-20 x 1" LG 130 10648 SCR SHC #10-32 x 1/2 LG 131 05187 SCR SHC #2-56 x 1/2 232 19042 Switch Assembly 133 19018 Plate - Travel Switch - Non-Swivel 1

07070 Plate - Travel Switch - Swivel 134 05203 SCR SHC #8-32 x 3/4 235 19026 Feed Motor Assembly 1

02217 Set SCR #8-32 x 3/16 119027 Motor Gear 1

36 19028 Gear - #4 & #5 Assembly 138 19029 Gear #3 & Clutch Assembly 1

05107 Ball Bearing 35mm x 47mm x 7mm 124100 Ball Bearing 3

40 08161 Gear Box Cover 141 51044 SCR SHC #10-32 x 1-1/4 242 41048 SCR SHC #10-32 x 1-1/2 445 07834 Gib - Right Hand 146 07838 Gib - Left Hand 147 07842 Gib 1

07831 Coolant Arbor Assembly Non-Swivel08115 Coolant Arbor Assembly Swivel

Item Part # Description Qty54 07872 Arbor - Coolant 155 07162 Collar Ejector 156 07079 Spring Seat 157 40256 SCR Set 5/16-18 x 3/8 Oval Pt 158 10517 Ring - Retaining Internal 259 40222 SCR Set 7/16-14 x .305 260 40312 Pin-Roll 3/16 dia x 1.564 Altered 161 05049 Spring - Comp 162 07436 Washer - Rubber 163 07440 Washer - Shim 12 x 18 x .5mm 164 40302 Ring - Retaining 265 40301 Washer, Thrust 1-3/8 x 2-1/16 x 1/32 266 07445 Coolant Inducer 1

40300 O-Ring (not shown) 107447 Hose Fitting (not shown) 107082 SCR BHC 1/4-28 x 1/4 (not shown) 1

67 40398 Ring - Retaining 168 40234 Washer, Thrust 269 08113 Front Support Bracket Assy. Swivel 1

07870 Front Support Bracket Assy. Non-Swivel 1

HMD927 BreakdownItem Part # Description Qty48 40594 Bolt - Hex HD 3/8-24 x 3" Non-Swivel 2

07088 Bolt - Hex HD 3/8-24 x 2-1/4" Swivel 249 40391 Lock Washer - Helical 3/8 250 40392 Washer - Flat 3/8 Type A 251 07831 Arbor Assembly Non-Swivel 1

08115 Arbor Assembly Swivel 152 10553 SCR SHC 1/4-20 x 7/8 LG 253 90028 Lock Washer - Helical 1/4 3

Accessories Included10565 Hex Key 1/8 wrench 104558 Feed Handles 304532 Feed Handle Knobs 310730 Safety Chain 3/16 X 5’ w/Snap Hook 124166 T-Handle Hex Key Wrench 113013 5/32" Allen Wrench 1

english

10

CONTROL PANEL BREAKDOWN & WIRING

08142 Panel Assenbly 230VItem Part # Description Qty

1 08139 Faceplate 12 01335 Switch - Motor Off 13 01228 Cover - Switch Red 14 01334 Switch - Motor On 15 02409 Cover - Switch Green 16 05336 Boot - Mini, Toggle Switch 17 04614 Switch - Rocker Illuminated 18 04891 Standoff - 3/8 LG 59 05832 Standoff - Nylon 3

10 05320 SCR-SLOT HD 311 05319 Nut - Plastic 312 04877 Wire Harness 113 04878 Spacer - LED 114 04881 Bulb - LED 115 04879 Lens - LED 116 01226 Guard - Switch 117 07392 Guard - Toggle Switch 118 08673 Circuit Board - Power 119 05355 SCR-PHMS #4-40 x 1/4 520 08156 Circuit Board - Autofeed 121 05335 Mini Toggle Switch Asm 222 05331 Jumper - Two Wire 123 05332 Jumper Two Wire 1

1

2 & 3

4 & 5

6

7

16

Magnet

J1


6

��

��

�

��

��

��

�

��

��

��

��

��

��

��

8

9, 10 & 11

12, 13, 14 & 15

17

19

Drill Motor White Wire

Drill Motor Black Wire

18

20

21

22 23

Feed Motor

21

Slide Safety Switch

Magnet Safety SwitchMagnet Pilot Light

Ground

Pwr White Wire

Pwr Black Wire

IMPORTANT NOTE:Circuit board must NOT have red jumpers in JP1 or JP2 positions

(jumpers are for 230V Operation Only)

JP2

J5

J2J1

J4J11

J10

11

MOTOR SLIDE ASSEMBLY BREAKDOWN

08140 Motor & Slide AssemblyItem Part # Description Qty

1 08141 Motor Complete Assembly 12 40038 SCR BHC #10-32 x 5/8 LG 53 08062 Bottle Support 14 10560 Lock Washer Ext. #10 35 07955 Slide - Dovetail 16 08001 Rack - Gear 17 05185 Pin - Dowel 18 90028 Lock Washer Helical 1/4 49 10624 SCR SHC 1/4-20 x 3/4 410 51044 SCR SHC #10-32 x 1-1/4 1

9

1

2

3

4

5

6

7

8

10

08103 Swivel Magnet AssemblyItem Part # Description Qty

1 07216 Plug Hole 4

2 05659 Clamp Handle Assembly 13 08094 Swivel Plate 14 02898 Dowel Pin 15 08095 Slide Plate 16 05743 SCR FHC 1/4-20 x 3/4 LG 67 07215 Bushing - Flange 18 05658 Pivot - Rod 19 90237 Washer - Flat #10 1

10 41044 SCR BHC #10-32 x 3/8 LG 111 05652 Ball Switch Assembley 112 08104 Magnet & Safety Switch Asm 1

05653 Plunger (not shown) 113 24144 D - Ring 114 41046 SCR SHC #10-32 x 1/2" LG 415 07887 Plate - Retaining Ring 116 07230 Label - Swivel Warning 1

SWIVEL BASE MAGNET ASSEMBLY BREAKDOWN

1

2

3

4

65

7

8

9

10

11

13

14

15

16

6

12

english

12

MOTOR PARTS DIAGRAM

23

4

5

6 78

9

10

1112

1314

15 16

17

18

1920 21

22

08141 Motor AssemblyItem Part # Description Qty Item Part # Description Qty

1 08234 SCR SHC #10-32 X 1-5/8 4 21 07969 Gear Box Cover 12 50038 Washer - Lock Helical #10 6 22 08070 Washer - Spring 13 07860 Retaining Ring 1 23 08025 SCR - SHC #10-32 x 3-1/4 LG 24 40274 Bearing 25mm x 47mm x 12mm 1 24 08045 Armature Assembly 15 07966 Gear Box Housing 1 25 07958 Baffle 16 08069 SCR - Shsld 3/16 x 7/8 1 26 08046 Field 17 07908 Switch 1 27 07953 Motor/Brush Holder Assembly 18 07910 Spring - Comp 1 28 07961 Carbon Brushes 29 07976 Spindle - Motor Drive 1 29 07960 Brush Holder Cap 210 07904 Key - 3/16 x 3/16 x 3/4 1 30 07848 Cover - Brush Access 111 07975 Gear Spur Removable - 49 Tooth 1 31 02385 SCR BHC #6-32 x 1/4 412 24100 Ball Bearing 3 32 41042 SCR BHC #8-32 x 3/8 LG 113 24160 Retaining Ring 1 33 10538 Washer - Lock #8 114 07977 Shift Control Rod Arm 1 34 08337 Motor Cord 115 07974 Gear Spur Removable - 15 Tooth 1 35 08136 Motor Label 116 07978 Key - 3/16 x 3/16 x 1-1/2 1 36 08044 Motor Specs Labels 117 07973 Assembly - Change Gear 250/450 118 07972 Assembly - Gears #2 & #3 119 17610 Washer - Flat 8mm 220 07903 Needle Bearing 2

23

24

25

26

27

2829

30 31

32

33

1

2

12

12

34

35

36

13

english

MAINTENANCE

ADJUSTMENT OF GIBS

1. Check gibs regularly to make certain they are tight. Tighten as required.2. Loosen all Gib Screws.3. Feed the drill in and out a few times and then, with top of motor slide flush with top of housing, tighten the Gib Screws until you feel them touch the Steel Gib.4. Feed the drill in and out again.5. Adjust Gib Screws so that there is uniform pressure from top to bottom. (Top of motor slide flush with top of housing.)6. Turn each Gib Screw in about 1/8 to 1/4 turn, depending upon your preference.7. Gibs should be tight enough so that slide moves up and down smoothly with no wobble or shaking. (Looseness will cause cutter breakage.) NOTE: Gibs should be lubricated regularly.

ARBOR ADJUSTMENT

Adjust Gibs before adjusting front support bracket.1. Arbor support bracket may become loose over time. Check Arbor Support bolts regularly to make certain they are tight. Tighten as required.1. Loosen Arbor Support Bracket Bolts.2. Be sure top of arbor is flush with the shoulder on motor output shaft. Also make certain arbor is securely fastened.3. Turn feed handle until motor and spindle are at the bottom of their travel.4. Tighten Arbor Support Bolts.5. Feed slide up and down a few times, checking for free and uniform movement.

Loosen / TightenGib Screws

(1/8” hex wrench)

Feed SlideUp and Down

Motor Slide Levelwith Housing

Tighten to 33 ft/lbs(400 in/lbs)

In order to minimize wear on moving parts and to insure smoother operation and longer life for your magnetic drill, the following maintenance should be done periodically, based on use.1. Regularly tighten all fasteners and replace all worn parts.2. Check motor brushes and replace if worn. 3. Check power cord and cord from panel to motor and, if cracked or frayed, return to an authorized repair center for replacement.4. Apply grease to the slide dovetails, brass gibs, and the feed gear rack. For best results use Shell Cyprina-RA or equivalent.5. Remove arbor (see arbor removal on page 14) and pack the bearing in the front support bracket with grease. Use Shell

Cyprina-RA or equivalent.6. The safety switch plunger should be clean and lubricated with penetrating oil periodically. As necessary remove the magnet

from drill and remove safety switch assembly from magnet. Push the plunger out of magnet. Clean out any debris from inside an around plunger hole in magnet. Coat the plunger with anti-seize. Replace plunger and safety switch assembly and tighten down

screws. Replace magnet into drill housing.

14

ARBOR & FRONT SUPPORT BRACKET REMOVAL AND INSTALLATION

Removal1. Loosen arbor support bracket bolts.2. Remove screw in coolant inducer. Rotate arbor until arbor screw is in line with hole.3. Loosen set screw holding arbor onto motor output shaft.4. Remove arbor.

Installation1. Hand tighten front support bracket bolts. Do not tighten all the way.2. Slide arbor to full up position and hold arbor in position over slot drive motor output shaft. 3. Tighten set screw to hold arbor onto motor output shaft.4. Replace coolant inducer screw.5. Turn feed handle until motor and arbor are at the bottom of their travel. 6. Tighten front support bracket bolts to 400 in/lbs.7. Run motor for 10 seconds. (If visual movement of arbor is noticed, restart at step 1)8. Re-check for tightness of arbor set screws.

1

2

Coolant Arbor

SWIVEL BASE INSTRUCTIONSThe threads on the clamp handle assembly are a Left Handed thread meaning,turning clockwise would loosen the assembly and turning counter clockwise would tighten the assembly. The clamp handle is spring loaded, so you will need to lift & turn the entire clamp handle assembly when repositining as if to be a ratchet drive.

1. Lift the Clamp Handle Assembly, rotated counter- clockwise and release. This will reposition the lever for more movement.2. With the Clamp Handle Assembly now down, pull the Clamp Handle Assembly clockwise. With this being a left handed thread, this will loosen the assembly.3. If more travel is needed, lift the clamp handle assembly, rotate counter clockwise and release.4. Pull the clamp handle assembly clockwise again. This amount of movement should be adequate to reposition the drill, more movement that this may cause the Magnet to disengage from the drill base.

1. Lift the Clamp Handle Assembly, rotated counter- clockwise and release. This will reposition the lever for more movement.2. With the Clamp Handle Assembly now down, pull the Clamp Handle Assembly clockwise. With this being a left handed thread, this will loosen the assembly.3. If more travel is needed, lift the clamp handle assembly, rotate counter clockwise and release.4. Pull the clamp handle assembly clockwise again. This amount of movement should be adequate to reposition the drill, more movement that this may cause the Magnet to disengage from the drill base.

To Loosen the Swivel Plate Assembly To Tighten the Swivel Plate Assembly

1 2 1 2


Work Area




Electrical Safety






Personal Safety








Tool Use and Care









Service





Work Area




Electrical Safety






Personal Safety








Tool Use and Care









Service




Clamp Handle MUST BE TIGHT prior to cutting holesEquipment damage or personal injury could occur

To Loosen the Swivel Plate Assembly

1. Lift the Clamp Handle Assembly, rotate counter- clockwise and release. This will reposition the lever for more movement.2. With the Clamp Handle Assembly now down, pull the Clamp Handle Assembly clockwise. With this being a left handed thread, this will loosen the assembly.3. If more travel is needed, lift the clamp handle assembly, rotate counter-clockwise and release.4. Pull the Clamp Handle Assembly clockwise again. This amount of movement should be adequate to reposition the drill. More movement than this may cause the Magnet to disengage from the drill base.

To Tighten the Swivel Plate Assembly

1. Lift the Clamp Handle Assembly, rotate clockwise and release. This will reposition the lever for more movement.2. With the Clamp Handle Assembly now down, push the Clamp Handle Assembly counter-clockwise. With this being a left handed thread, this will tighten the assembly.3. If more travel is needed, lift the Clamp Handle Assembly, rotate clockwise and release.4. Push the Clamp Handle Assembly counter-clockwise again. Continue this process until the Swivel Assembly is tight.

The threads on the Clamp Handle Assembly are a Left Handed thread. Meaning, turning clockwise will loosen the assembly and turningcounter-clockwise will tighten the assembly. The Clamp Handle Assembly is spring loaded, so you will need to lift & turn the entire ClampHanndle Assemblt when repositioning , as if to be a ratchet drive.

SWIVEL BASE INSTRUCTIONS

15

english

1. Keep the inside of Hougen Cutter clear of chips. Chips will interfere with cutting to maximum depth, maybe impede the free oil flow and can cause cutter breakage.

2. Keep work, machine, arbor and Hougen Cutter free of chips and dirt.3. Tighten all bolts and fasteners regularly.4. We highly recommend using a light viscosity cutting fluid (preferably Hougen Cutting Fluid.5. Occasionally check metering of cutting fluid flow. Lack of cutting fluid may cause Hougen Cutter to freeze in cut, slug to stick and may result in poor cutter life.6. Always start cut with light feed pressure and then increase sufficiently to achieve maximum cutting rate.7. Ease off on pressure as cutter begins to break through at the end of the cut.8. Keep slide dovetails, brass gibs and feed rack lubricated and free of chips and dirt. 9. When slug hangs up in cutter, turn off motor and bring cutter down on a flat surface. This will normally straighten a cocked slug,

allowing it to be ejected. 10. When cutting large diameter or deep holes it may be necessary to stop in the middle of the cut to add cutting fluid and remove the

chips from around the arbor. (When doing this DO NOT raise the cutter out of the hole. Doing so can allow chips to get under the teeth of the cutter. This will make it difficult to restart the cut.)

"Babying" the cutter through the cut will only decrease tool life.

#1 cause of cutter breakage and

prematurely dull teeth is too little

feed pressure

1. Trouble: Magnetic base won’t hold effectively to work. a. Cause: Chips or dirt under magnet. Remedy: Clear area of chips and dirt. b. Cause: Irregular surface on bottom of magnet or on workpiece. Remedy: Lightly surface grind the bottom of the magnet flat and/or file imperfections flat on the work surface as needed.

2. Trouble: Cutter tends to move across surface of work. a. Cause: Magnetic base not holding effectively. Remedy: See causes and remedies under No. 1 above. b. Cause: Too much feed pressure at start of cut. Remedy: Use light pressure until a groove is cut. The groove then serves as a stabilizer. c. Cause: Worn pilot. Remedy: Replace pilot d. Cause: Worn cutter. Remedy: Replace or have cutter resharpened.

3. Trouble: Out of round holes. a. Cause: Worn arbor support bracket bearing and or ejector collar. Remedy: Replace: (only a few thousandths wear permissible.) b. Cause: Misaligned support bracket Remedy: Realign support bracket c. Cause: Misaligned or loose arbor set screw. Remedy: Tighten set screw.

4. Trouble: Motor and slide won’t stay in set position a. Cause: Gibs too loose Remedy: Adjust gibs

5. Trouble: Erratic or intermittent feed. a. Cause: Worn or pinion and/or rack. Remedy: Replace worn parts.

6. Trouble: Motor doesn’t run when motor START button is pushed. a. Cause: Magnet is not turned on Remedy: Push magnet ON button. b. Cause: Magnet on rough or dirty work surface and safety switch not fully depressed. Remedy: File work surface flat and clean all chips and oil from under magnet. c. Cause: No power Remedy: Check power source and extension cords. e. Cause: Worn motor brushes Remedy: Replace brushes f. Cause: Faulty motor START switch Remedy: Return unit to an authorized repair center to have switch replaced.

NOTE: If you are unable to correct any malfunction after trying the above, do not attempt to operate the drill. Return the unit to the factory or authorized repair center for service.

HINTS FOR SMOOTHER OPERATION

REMEDIES FOR HOLEMAKING PROBLEMS

15

16

COMMERCIAL / INDUSTRIAL LIMITED WARRANTY

Hougen Manufacturing, Inc.P.O. Box 2005 • Flint, MI 48501-20053001 Hougen Drive • Swartz Creek, MI 48473Phone (810) 635-7111 • Fax (810) 635-8277www.hougen.com • [email protected]© 2018 Hougen Manufacturing, Inc.

HOUGEN AUTHORIZED WARRANTY REPAIR CENTERSHougen Authorized Warranty Repair Centers have been factory trained to properly service and repair

Hougen Portable Magnetics Drills. To locate an Authorized Warranty Repair Centers near you, please visit: www.hougen.com

Hougen Manufacturing, Inc. warrants its Portable Magnetic Drills and Trak-Star Rail Drills for two (2) years, Electro-hydraulic Hole Punchers and Tornado II Paint Shakers for one (1) year, and it's Husqvarna Saw and other products for ninety (90) days from date of purchase against defects due to faulty material or workmanship and will repair or replace (at its option) without charge any items returned. This warranty is void if the item has been damaged by accident or unreasonable use, neglect, improper service, or other causes not arising out of defects in material or workmanship. No other expressed warranty is given or authorized. Hougen Manufacturing, Inc. disclaims any implied warranty of Merchantability or fitness for any period beyond the expressed warranty and shall not be liable for incidental or consequential damages. Some states do not allow exclusion of incidental or consequential damages or limitation on how long an implied warranty lasts and, if the law of such a state governs your purchase, the above exclusion and limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

To obtain warranty service, return the item(s), transportation prepaid to your nearest Factory Authorized Warranty Service Center, or to Hougen Manufacturing, Inc., 3001 Hougen Drive, Swartz Creek, MI 48473.

This warranty is in lieu of any other warranty, expressed or implied, including any warranty of merchantability or fitness for a particular purpose.

Photographs and Specifications shown are accurate in detail at time of printing. Manufacturer reserves the right to make improvements and modifications without prior notice. Hougen, Rotabroach,

and Hougen-Edge are proprietary trademarks of Hougen Manufacturing Inc.

Documents

HMD927 SERIES POWER FEED MAGNETIC DRILL · OM9270717BEF Printed in U.S.A. 11/2018 operator’s manual HMD927 SERIES POWER FEED MAGNETIC DRILL Covers Drill Part Numbers: 0927202 0927204