Upload
others
View
9
Download
0
Embed Size (px)
Citation preview
�
Please read this guide completely before starting. For questions about this and other Andersen® products, call �-888-888-7020.
For the most current version of this guide visit www.ander senwindows.com . Consult your local building code official for applicable building codes and regulations. Thank you for choosing Andersen® products.
Please leave this information with homeowner.
KeynUpper Split Arm Hinge (white shoe)nLower Split Arm Hinge (black shoe)nLower Split Arm Hinge with Control Bracket, 20" (black shoe)nUpper Straight Arm Hinge, 22" or 4-Bar HingenLower Straight Arm Hinge, 22" or 4-Bar Hingen#8 x 5/8" Screwn#8 x 5/8" Stopper Screw *
* Used during reinstallation of sash.
Hinge Replacement/Conversion Guidefor Casement Windows
Parts Included(1) Installation Guide(2) Split Arm Hinges or Split Arm Hinges with Control Bracket, 20"(12) #8 x 5/8" Screws(2) #8 x 5/8" Stopper Screws * or(1) Installation Guide(2) Straight Arm Hinges, 22" or 4-Bar Hinge (12) #8 x 5/8" Screws
4Before beginning hinge replacement, remove sash and existing hinges following the instruction guide for casement window sash replacement.
Supplies Needed· Silicone Sealant (color matching)· Wood Plugs
Tools Needed· Safety Glasses· Phillips Screwdriver· Hammer· Pencil
nD
nA
nB
0005462 BA Revised 04/13/06
“Andersen” is a registered trademark of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation. ©2006-2006 Andersen Corporation. All rights reserved.
nF
nC nG
or
· Drill· 3/32" Drill Bit· Tape Measure· Caulk Gun
Use caution when working at elevated heights and around unit openings. Follow manufacturer’s instructions for safe operation of ladder and/or scaffolding. Failure to do so may result in injury or death.
Follow manufacturer’s instructions for safe operation of hand/power tools. Always wear safety glasses. Failure to do so may result in injury and/or product damage.
nA
nF
nE
A BC
DEFG
Limited Publication Release
or
Left hand hinges shown in this guide.
4Interior
Hole Locations
3Exterior
22
Split Arm Hinge Replacement
0005462
Position lower hinge channel tight to corner of frame, as shown, and mark indicated hole locations. Repeat for upper hinge channel.
Drill holes 1/8" deep using a 3/32" drill bit at marked locations.
Position hinge channels over drilled locations and fasten to frame. Position sash interior side up. Mark 1-3/4" from sash corner, as shown.
4For Split Arm Hinge Replacement proceed below.
4For Straight Arm Hinge Replacement proceed to page 3.
Fill and seal old screw holes in frame. Fill and seal old screw holes in sash.
2Interior
1Exterior
Silicone
Caulk Gun
Hammer
Hammer
Repeat at top Repeat on opposite side
Wood Plug
Wood Plug
Pencil
Silicone
Hinge Channel
Pencil
3/32" Drill Bit
1Exterior
2Exterior
Phillips Screwdriver
Hinge Channel
#8 x 5/8" Screw
�-3/4"
Sash Corner
Sash Lip
Drill
7Interior
3
Position hinges over drilled locations and fasten to sash. Reinstallsashfollowinginstructionguideforsashreplacement.
0005462
Drill holes 1/8" deep using a 3/32" drill bit at marked locations.Position hinge channel tight to corner of frame, as shown, and mark hole locations. Repeat for upper hinge channel.
1Exterior
2Exterior
Straight Arm Hinge Replacement
Upper Hinge (white shoe)
Lower Hinge (black shoe)
Pencil
Hinge Channel
Hole Locations
6Interior
Drill holes 1/8" deep using a 3/32" drill bit at marked locations.
3/32" Drill Bit
3/32" Drill Bit
Phillips Screwdriver
#8 x 5/8" Screw
5Interior
Place hinge on sash lip, center first screw hole over marked location and mark screw holes, as shown.
Upper Hinge (white shoe)
Lower Hinge (black shoe)
Hole LocationsPencil
First Screw Hole(centered over mark)
Sash Lip
Drill
Drill
5Interior
6Interior
4Interior
3Interior
4
Position hinges over drilled locations and fasten to sash. Reinstallsashfollowinginstructionguideforsashreplacement.
Drill holes 1/8" deep using a 3/32" drill bit at marked locations.
Place hinge on sash lip, center first screw hole over marked location and mark screw holes, as shown.
3/32" Drill Bit
0005462
Pencil
Phillips Screwdriver
Upper Hinge Channel
Upper Hinge Channel
#8 x 5/8" Screw
Position sash interior side up. Mark 1-3/4" from sash corner, as shown.
Pencil
�-3/4"
Sash Corner
Sash Lip
Hole Locations
First Screw Hole(centered over mark)
Sash Lip
Drill