Embed Size (px)
Citation preview
For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd
DRAWER REMOVAL/ INSERTION Guide
Page 1 For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd
DRAWER
Guide
Step 2.In one smooth motion, lift the front of the drawer, this will disconnect the runner from the connectors on the base of the drawer. Once properly separated a click will be heard and the drawer will be separate from the runner.
If this motion is not done with enough force then the drawer may need to be lifted again. Be careful not to lift the runners whilst lifting the drawer.
Step 3.The drawer is free to remove from the unit Simply remove the loose drawer from the unit, making sure not to damage the unit in the process.
Step 1.Open the drawer that is required to be removed. Pull out the drawer until the runners are at full maximum extension.
DRAWER REMOVAL
CLICK
REMOVAL
Page 2For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd
DRAWER
Guide
Step 1.Fully extend the drawer runners out of the unit. (for the drawer you are inserting)
Step 3.Once the drawer is placed onto the runners, pull forward the protruding lips on the ends of the runners until a click is heard. Once the click is heard the drawer is properly located and secured to the runner.
Push the drawer back into the Unit.
Step 2.Place the drawer onto the runners, making sure that the groove of the drawer sides and the runner mechanism are aligned.
DRAWER INSERTION
CLICK
INSERTION
Page 3 For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd
DRAWER
Guide
SINGLE
Adjustment
Drawer sidefixing clip
Drawer frontal
Drawer side
DRAWER FRONTALADJUSTMENT
Screw point 1 as shownto adjust drawer frontal right & left.
Releasing fixing clip. Screw point 3 whilst applying downward pressure as shown to release.
Screw point 2a as shown to adjust drawer frontal up & down.
Tighten 2b once in position.
View on side of drawer side
1
2b
2a3
Drawer Cover Cap
Fixing clip
Step 2.Push fit drawer side fixing clips onto drawer side.
Step 3.Fit drawer cover caps over drawer side adjustment.
Step 1.Secure drawer side fixing clips using 2 x 21mm screws per clip using the predrilled holes.
99mm
67mm
99mm
67mm
StandardDrawer
37mm37mm
SINGLE DRAWER
Page 4For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd
DRAWER
Guide
DEEP
Adjustment
Drawerfront
Drawer side
Gallery head fixing clip
Drawer sidefixing clip
Drawer Cover Cap
Step 4.Fit drawer cover caps over drawer side adjustment.
Fixing clip
Deep Drawer
231mm 231mm
99mm
67mm
37mm37mm
67mm
99mm
BA
Step 1.Secure gallery head fixing clips using 1 x 15mm screw and secure drawer side fixing clips using 2 x 21mm screws located with the predrilled holes.
Step 3.A. Clip gallery rail into the top corners of the metal back panel.
B. Locate front end of the gallery rail into the opening of the gallery head fixing clip, which is secured to the frontal as shown.
Step 2.Push fit drawer fixing clips onto drawer sides.
DEEP DRAWER
View on side of drawer sideDRAWER FRONTALADJUSTMENT
Screw point 1 as shown to adjust drawer frontal right & left.
Screw point 2a as shown to adjust drawer frontal up & down.
Tighten 2b once in position.
Releasing fixing clip. Screw point 3 whilst applying downward pressure as shown to release.
Page 5 For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd
DRAWER
Guide
GLASS DEEP
Deepdrawer
195mm
131mm
99mm67mm
Fixing clip
Glass SideFixing Clip
Fixing clip
Glass SideFixing Clip
195mm
131mm
99mm67mm
Step 1.Secure glass side fixing clips using 2 x 15mm screws. Secure drawer side fixing clips using 2 x 21mm screws in pilot holes provided as shown below.
Step 3.Fit glass sides with end caps attached.
Use the groove on the front end cap as a guide to slide into place onto
frontal glass fixing clip, and into metal back as shown.
Fixingclip
GlassClip
Drawer frontal
Step 2.Push fit drawer side fixing clips onto drawer side.
Fixingclip
Step 4.Fit drawer cover caps
over drawer side adjustment.DrawerCover Cap
Screw point 1 as shown to adjust drawer frontalright & left.
Drawer Frontal Adjustment
Screw point 2a as shown to adjustdrawer frontal up & down.
Tighten 2b once in position.
Releasing fixing clip.Screw point 3 whilst applyingdownward pressure as shownto release.
View on side of drawer side
1
3 2a
2b
Drawer frontal
Drawer Side
37mm37mm
Rear end clip release catch,
depress & lift to remove side.
Page 6For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd
DRAWER
Guide
GLASS MIDFor use with 2 + 1 Internal Unit
Releasing fixing clip.Screw point 3 whilst applyingdownward pressure as shownto release.
Step 1.Secure gallery head fixing clips using 1 x 15mm screw. Secure drawer side fixing clips using 2 x 21mm screws in pilot holes provided as shown below.
Step 3.1. Clip gallery rail into the top corners of metal back
panel. 2. Locate front end of the gallery rail into the
opening of the gallery head fixing clip, which is secured to the frontal as shown.
Step 2.Push fit drawer fixing clips onto drawer side.
Fixingclip
Drawer side
Drawer frontal
2
1
Step 4.Fit Drawer Cover Caps
over drawer side adjustment.
DrawerCover Cap
View on side of drawer side
Drawer Frontal AdjustmentScrew point 1 as shown to adjust drawer frontalright & left.Screw point 2a as shown to adjustdrawer frontal up & down.Tighten 2b once in position.
Releasing fixing clip.Screw point 3 whilst applying downwardpressure as shown to release.
1
3 2a
2b
Drawer frontal
Gallery head fixing clip
Fixingclip
Gallery HeadFixing Clip
Gallery HeadFixing ClipMid
drawer
191mm
99mm67mm
Fixing clip
Fixing clip
191mm
99mm67mm
37mm37mm
Page 7 For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd
DRAWER
Guide
GLASS MIDFor use with 2 + 1 Internal Unit
Step 1.Secure glass side fixing clips using 2 x 15mm screws, secure drawer side fixing clips using 2 x 21mm screws in pilot holes provided as shown below.
Step 3.Fit Glass Sides with End Caps attached.
Use the groove on the front End Cap as guide to slide into place onto
Frontal Glass Fixing Clip, and into Metal Back as shown.
Step 2.Push fit drawer fixing clips onto drawer side
Fixingclip
GlassClip
Drawer frontal
Step 4.Fit Drawer Cover Caps
over drawer side adjustment.DrawerCover Cap
Rear End Clip release catch,
depress & lift to remove side.
Drawer Frontal AdjustmentScrew point 1 as shown to adjust drawer frontalright & left.
Screw point 2a as shown to adjustdrawer frontal up & down.
Tighten 2b once in position.
Releasing fixing clip.Screw point 3 whilst applyingdownward pressure as shownto release.
View on side of drawer side
1
3 2a
2b
Drawer Side
Drawer frontal
Fixingclip
Middrawer
Middle DrawerFixing Clip
Middle DrawerFixing Clip
Top DrawerFixing Clip
Top DrawerFixing Clip
176mm
131mm
99mm67mm
176mm
131mm
99mm67mm
37mm37mm
