Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Guide to Measuring Your Space
CUSTOMER’S NAME PHONE
DESIGNER PHONE
APPOINTMENT DATE TIME
Proof 13Final
10/04/2013
FREE
HD Kitchen Measuring Guide_2013 Size: 8.375” x 10.875”Ink: Black + PMS 583Stock: 60lbs. Opaque Text
Printer: Knepper
2013Print Qty: 125,000
2 | For more information, visit www.woodmarkcabinetry.com
Accurate measuring is a critical step in the
remodeling process. Measurement errors
are a source of significant delays and
costly overruns.
Obtaining a professional measurement of your
space is highly recommended — talk to your
designer for more details.
Please read ALL of these instructions carefully from start to finish before beginning to measure your space. For more information, visit
www.woodmarkcabinetry.com
Measure in INCHESCabinets and appliances are measured in inches, so your drawings should be recorded in inches, not feet and inches.
Example: 138-1⁄8 in. NOT 11 ft. 6-1⁄8 in.
For walls and openings, ROUND DOWNWhen you measure ceilings, walls and openings, round down to the nearest 1/8 inch.
Example: 138-1⁄8 in. NOT 138-3 ⁄16 in.
For appliances, ROUND UPWhen you measure appliances round up to the nearest inch.
Example: 36 in. NOT 35-11⁄16 in.
Recording your measurementsWe've provided graph paper to help with your final drawings. It is much more important to record accurate dimensions, rather than draw your room to a precise scale. Be sure to write the actual dimensions on your drawings for all the elements in your space.
1/2
1 full inch
Record this as 12 inches, NOT 1 foot
Record this as 13 inches,
NOT 1 foot, 1 inch
3/4
1/4 1/8
Do not use this side of the ruler, or metric measurements
You do not need to measure closer
than 1/8 inch.
MEASURING YOUR SPACEThis guide walks you through the five easy steps to create
drawings and provide the information necessary for your
kitchen designer to start the design process:
1 Floor Plan Drawing . . . . . . . . page 4A birds-eye view of your space
2 Wall Elevation Drawing . . . . . . page 5A vertical and horizontal map of each wall, from a straight-on view
3 Construction Details . . . . . . . page 6Important information for your renovation project
4 Appliances . . . . . . . . . . . . page 6Dimensions and manufacturers' specs for your appliances
5 Photography . . . . . . . . . . . page 6Photos of your space before renovation
Standard US construction materials are measured in inches. Use a US tape measure and record your dimensions in inches, not feet and inches.
IMPORTANT NOTES ABOUT MEASURING FOR RENOVATIONS
Before your Kitchen Designer can begin to design your new
space and help you select your cabinetry and appliances, they
will need to know the size of your space and the important
construction details.
USE ONLY METAL MEASURING TAPESCloth or plastic tapes may stretch, causing measuring errors.
Proof 13Final
10/04/2013
3
Proof 13Final
10/04/2013
Measuring doors and windowsYour designer needs to know the exact location of windows and doors, as well as the size of each opening (including the trim) in order to plan your new space.
Record all of these measurements:
A. Width, including trim
B. Height, including trim
C. Distance from floor
D. From floor to top of window
E. Width of the window sill
C
B
D
A
E
Floor
B
A
Locate windows and doorsMeasure from the wall to the outside edge of the trim on all your doors and windows.
Range hoodsIf you have an existing range hood vent or over the range wall microwave, note the location on your drawing. Specify if it exhausts back into the room, or if it has ducts that vent to outside.
220 volt outletsBe sure to show any 220 volt outlets on your drawing. Do you have an electric stove? Then you'll have a 220 volt outlet for your stove. Your outlet may not look exactly like the example shown here, but it will look different from standard 110 volt outlets.
Locate water and utility linesMark the center line location of the sink, water lines, drains, gas lines and heating/air conditioning vents.
Locate outlets and switchesMeasure horizontally to the center of the wall plate and vertically from the floor as shown.
MEASURING TIPSHere are helpful tips on how to properly
measure your space and record the correct
window, door and utility information for
your floor plan and wall elevation drawings.
Always double-check your measurements!
IMPORTANT!
Be sure to write the
measurements on
your drawings!
Most grid paper is to scale, but your designer won't know what size your space is unless
you write down the dimensions.
23 1/8"
Round down to the nearest 1/8 inch, and write it on your drawings.
4 | For more information, visit www.woodmarkcabinetry.com
CREATING A FLOOR PLAN DRAWINGA Floor Plan is a "bird's eye" view of the whole
room, showing all four walls and the location
of important utilities.
Start with your wall drawingsStart your Floor Plan with Wall A, the sink wall. Then go clockwise around the room with walls B, C, and D. Mark the locations of openings and fixtures along the wall segments.
Locate ceiling lights and other fixturesMeasure in two directions to locate the center of ceiling lights, fans, air vents, and any other fixtures in the floor or ceiling.
Locate islands and peninsulasIf there is an existing island or peninsula, mark its size and location. Mark any outlets or utilities coming to these structures.
Always double-check your measurements!The total of your wall segments must equal your overall wall length.
Example: 62-1/2 in. + 36 in. + 39-3/4 in. = 138-1/4 in.
Transfer measurements to gridTransfer all of your measurements to the grid pages in this guide following the example below.
It is more important to write down the exact measurements than to draw the floor plan to scale.
1Proof 13Final
10/04/2013
5
Proof 13Final
10/04/2013 Elevation drawings are a straight-on view
of each wall, with all the features measured
vertically and horizontally, placing them on the
wall space. This helps your designer locate your
new cabinets and appliances along your walls.
Start with the sink wall, go clockwise from thereStart measuring your room with the sink wall. Label this Wall A. Then go clockwise around your room, labeling the walls B, C, and D.
Draw a rough sketchStart by drawing a rough sketch (or two!) of each wall on a separate sheet of paper.
Measure the width of the wallMeasure the full width of each wall, beginning in the left corner. Check the width at two locations, 6 inches above the finished floor and 6 inches below the ceiling. Use the smallest dimension.
Measure the height of the wallMeasure the full height of each wall, beginning in the left corner. Check the height at two other locations. Use the smallest dimension.
Locate the openingsMeasure to the outside edge of the trim. Then measure from the outside trim edge to the next opening, or to the far wall. Follow the measuring tips on page 2 to capture all the important details about windows and doors.
Locate fixtures and utilitiesMeasure horizontally to the center of outlets, switches, water lines and other utilities. Also measure the distance of these items from the floor. If there are HVAC wall vents, mark their location and size. Follow the measuring tips on page 3 for accuracy.
Transfer measurements to gridTransfer all of your measurements to the grid pages in this guide. Label your drawings Wall A, Wall B, Wall C and Wall D. Then begin the Floor Plan Drawing.
CREATING WALL ELEVATION DRAWINGS2
Always double-check your measurements! The total of your wall segments should equal your overall length.
If your floor plan looks like this drawing …
… your elevation view will look like this drawing.
If your space is L-shaped or has a bump out area, you can still draw an elevation view straight on. Just use a vertical line to show where the wall comes forward.
6 | For more information, visit www.woodmarkcabinetry.com
WARNING: Soffits typically contain electrical and plumbing elements that can’t be relocated. Consult a professional on your remodel.
Entrances and accessTo make sure your new products fit through doorways into your space, record the actual openings for doors and hallways.
Entry Door: inches
Interior Door 1: inches
Interior Door 2: inches
Hallway: inches
Is there a basement or crawl space under the room that provides access to plumbing and heating ducts?
❑ Yes ❑ No
Soffit / Bulkhead
Ceiling
Wall cabinets are often hung below
a soffit.
CONSTRUCTION DETAILSSoffitsA soffit, also called a bulkhead, is a wall section that is built out at the ceiling level, usually in the area above wall cabinets.
Does the room have soffits?
❑ Yes ❑ No
If yes, please fill out the two dimensions in the diagram to the right.
Do you plan to keep the existing soffits? ❑ Yes ❑ No
Will the soffits have recessed lighting after the renovation? ❑ Yes ❑ No
3
Appliance dimensions are critical to the overall fit of all kitchen components. Whether you are buying new appliances or using existing ones, provide the dimensions for each appliance in your kitchen. Door hinges and handles can obstruct surrounding cabinets and must be
factored into the design. Whenever possible, provide brand, model and spec sheets for appliances. Spec sheets are installation guides that list the dimensions of the appliance.Please provide all appliance information.
Existing New None Brand Model Dimensions W x D x H Spec Sheets Enclosed?
Sink n n n ✕ ✕ n Yes n No
Disposal n n n ✕ ✕ n Yes n No
Dishwasher n n n ✕ ✕ n Yes n No
Compactor n n n ✕ ✕ n Yes n No
Refrigerator n n n ✕ ✕ n Yes n No
Freezer, stand alone n n n ✕ ✕ n Yes n No
Range n n n ✕ ✕ n Yes n No
Cook Top n n n ✕ ✕ n Yes n No
Exhaust Hood n n n ✕ ✕ n Yes n No
Wall Oven n n n ✕ ✕ n Yes n No
Microwave, wall mount n n n ✕ ✕ n Yes n No
Microwave, countertop n n n ✕ ✕ n Yes n No
Other: n n n ✕ ✕ n Yes n No
Other: n n n ✕ ✕ n Yes n No
APPLIANCES4
Proof 13Final
10/04/2013
PHOTOGRAPHY5Take photos of your space and share them with your Kitchen Designer. Label your shots to match your walls: A, B, C, D
❑ Straight on views of each wall: A (the sink wall), B, C, D (go clockwise around the room.)
❑ Photos of soffits or other construction details
❑ Close ups of anything unusual in your space: air vents, plumbing or gas lines, entrances or access notes.
FLOOR PLANSee instructions on page 4.
Be sure to include these items on your drawing, using these symbols:
Scale: 3/4˝ = 1´
IMPORTANT:Some cabinets or appliances may not fit through an existing doorway. Make sure you measure the width of all doorway openings on this floor plan drawing.
Note:Keep in mind that each large square equals one foot and each small square equals 3 inches. The scale of this grid is 3/4” = 1’.
Door swing Show if the door opens in or out of the room, swings to the left or the right side.
❑ Wall Lengths
❑ Window & Door Openings
❑ Water Lines
❑ Drain Lines
❑ Heating Ventilation and Air Conditioning (HVAC) Vents
❑ 110 Volt Electrical Outlets
❑ 220 Volt Electrical Outlets
❑ Ceiling Light Locations
❑ Wall Light Locations
❑ Ceiling Fan Locations
❑ Thermostat
❑ Switches, Phone and TV
❑ Gas Line
❑ Range Hood
S
220
110
Ph
For more information, visit www.woodmarkcabinetry.com Para obtener más información, visite www.woodmarkcabinetry.com
159 1/2” 159 1/2”
S Ph
❑ Longitudes de pared
❑ Aberturas de ventanas y puertas
❑ Caños de agua
❑ Caños de drenaje
❑ Salidas de calefacción, ventilación y aire acondicionado (HVAC)
❑ Tomacorrientes de 110 voltios
❑ Tomacorrientes de 220 voltios
❑ Ubicaciones de luces de techo
❑ Ubicaciones de luces de pared
❑ Ubicaciones de ventiladores de techo
❑ Termostato
❑ Interruptores, teléfono y TV
❑ Caño de gas
❑ Campana de estufa220
110
IMPORTANTE:Algunos armarios o electrodomésticos podrían no caber por las puertas existentes. Asegúrese de medir el ancho de todas las aberturas de las puertas en este dibujo del plano.
Nota:Recuerde que cada cuadrado grande equivale a un pie y cada cuadrado pequeño equivale a 3 pulgadas. La escala de esta cuadrícula es 3/4” = 1’.
Abertura de la puerta Muestre si la puerta se abre hacia adentro o hacia fuera de la habitación, con un movimiento hacia la derecha o la izquierda.
PLANOVer instrucciones en la página 9.
Asegúrese de incluir estos elementos en el dibujo usando estos símbolos:
Escala: 3/4˝ = 1´
Ho
w to
indicate lo
cation o
f electrical o
utlets and sw
itches.
16˝
Indicates 16˝ from w
all to center of outlet. (Measured
from the left side, reverse if m
easuring from the right)
Indicates 42˝ from
floorIndicates
110 V outlet42˝
110
W
all lengths and heights,
and wall segm
ent lengths
(the space between item
s)
W
idth and height for doors & w
indows,
including the fram
es (see tips on page 3)
W
ater Lines & D
rains
G
as Lines
220 Volt Electrical O
utlets
110 Volt Electrical O
utlets
Sw
itches, Phone, TV
Be sure to
include these item
s on yo
ur draw
ing:
159 1/2"
110
220
SPh
TV
G
WALL ELEVATION DRAWINGSee instructions on page 5.
Open and remove folded insert to create Floor Plan and Wall Elevation drawings.
IMPORTANT!
Be sure to write the measurements on
your drawings!Most grid paper is to scale,
but your designer won't know what size your space is unless you write down the dimensions.
Materials List:Before you begin measuring your space, make sure you have all the tools you need on hand.
Tape measure (25' to ensure accuracy)
Pencil with eraser
Scrap paper
Ruler or straight edge
Step ladder
Digital camera
Recommended:
Assistant
Digital measuring tool
For more information, visit www.woodmarkcabinetry.com
Proof 13Final
10/04/2013
16.50”w x 21.50”h
English: Approved
Translations: Complete
HD Kitchen Measuring Guide_2013_Grid Insert
Grid Insert
Trim Size: 16.5” x 21.5”Folded Size: 8.25” x 10.75Ink: Black + PMS 583Stock: 60lbs. Opaque TextBinding: Folder and placed as center spread Printer: Knepper
2013Print Qty: 125,000
Abra y retire el anexo doblado para dibujar el plano y las elevaciones de pared.
¡IMPORTANTE!
¡Asegúrese de escribir las medidas
en sus dibujos!En general, el papel cuadriculado es a escala, pero su diseñador no sabrá el tamaño de su espacio a
menos que anote las dimensiones.
Lista de materiales:
Antes de comenzar a medir su espacio, asegúrese de tener todas las herramientas necesarias a mano.
Cinta métrica (de 25' para garantizar la precisión)
Lápiz con goma de borrar
Papel para anotaciones
Regla o borde recto
Escalera
Cámara digital
Se recomienda:
Asistente
Herramienta de medición digital
Para obtener más información, visite www.woodmarkcabinetry.com
DIBUJO DE LA ELEVACIÓN DE LA PARED Ver instrucciones en la página 8
Có
mo
indicar la ub
icación d
e tom
as de
corriente e interrup
tores.
16˝
Indica 16" desde la pared hasta el centro del tomacorriente. (M
edida desde el lado izquierdo; revertir si m
ide desde la derecha)
Indica 42" desde el suelo
Indica tomacorrien-
tes de 110 V42˝
110
Longitudes y alturas de paredes y longitudes de segm
entos de paredes (espacio entre artículos)
Ancho y altura para puertas y paredes, incluidos
los marcos (ver consejos en la página 10)
Caños de agua y desagües
Caños de gas
Tomacorrientes de 220 voltios
Tomacorrientes de 110 voltios
Interruptores, teléfono, TV
SPh
TV
Aseg
úrese de incluir esto
s elemento
s en el dib
ujo:
110220
G159 1/2"
ELEVATION
S: WA
LL C | ELEVACION
ES : PARED C
C
Scale: 1/2˝ = 1´ |
Escala: 1/2˝ = 1´
ELEVATION
S: SINK W
ALL, W
ALL A
| ELEVACION
ES : PARED DE FREG
ADERO, PA
RED AS
cale: 1/2˝ = 1´ | Escala: 1/2˝ = 1´
A
ELEVATION
S: WA
LL D | ELEVACION
ES : PARED D
D
Scale: 1/2˝ = 1´ |
Escala: 1/2˝ = 1´
ELEVATION
S: WA
LL B | ELEVACION
ES : PARED B
B
Scale: 1/2˝ = 1´ |
Escala: 1/2˝ = 1´