Upload
dinhlien
View
224
Download
3
Embed Size (px)
Citation preview
Glen Metals
Solutions in Steel
Please contact Glen Metals and one ofour COR-TEN® experts will deal withyour enquiry: -
www.glenmetals.com
Tel: 01236 424 396 Fax: 01236 433 330E: [email protected]
Head Office
ASD metal services - Tel: 0113 254 0711
ContactCOR-TEN®
a coat for allweathers
Advantages ofCOR-TEN®
Protection
Develops its ownprotective filmwhich slows therate of corrosion
Exhibits morefavourableproperties thanthat of mild steelat elevatedtemperatures (upto 800°C).
Its increasedstrength over mildsteel can allow aweight saving ofapproximately30%
Saves the cost ofinitial painting andthe maintenancecosts of repainting
Weathers to anatural browncolour (whichdarkens gradually)and complimentsthe surroundingenvironment
cost saving
strength
properties
protection
environment
Thicker moredurable zinccoatings areobtainablecompared toordinary carbonsteel whenutilising hot dipgalvanising, givingpossible costsavings overstainless steel
The chemicalcomposition givesbetter resistanceagainst acidacceleratedcorrosioncompared toordinary carbonsteel
The same paintsystems used fornormal carbonsteel can beapplied toCOR-TEN® torender up to twicethe functionalpaint life
Up to 12mm thick,welds with thesame facility asmild steelhowever itsgreater strengthmust beconsidered whenselecting awelding procedure
Painted areaswhich aredamaged willweather to aprotective film,inhibiting underpaint “creep”
welds
paint life
resistance
cost savings
Costs less than mildsteel that has beensubsequently coatedby conventionalmeans
coating
inhibiting
www.glenmetals.comwww.glenmetals.com
Glen MetalsThe COR-TEN® Specialists
Quality Strength Self healingEconomicBenefits
COR-TEN®The steel that protects itself
COR-TEN® is a high strength, low alloy, weldablestructural steel possessing excellent weatheringresistance. It may be used to advantage in the paintedor unpainted condition.
The steel owes its weathering characteristics to the formation of a
tightly adherent protective oxide coating which seals the surface
against further corrosion. The protective layer or ‘patina’ is of a
natural dark brown appearance and if chipped or damaged will
actually repair itself to give continuity of protection and
appearance.
COR-TEN® is particularly recommended for use where high
structural strength is required and where maintenance is difficult.
The colour of the ‘patina’ will be determined by the nature of the
atmosphere and the frequency with which the surface is exposed
to the wetting and drying cycle. As the ‘patina’ blends with many
natural surroundings, increasing use has been made of COR-TEN®
for aesthetic reasons in the current environmentally conscious
world.
Corrosion is a major factor in many branches of industry. High costs are incurred by therebuilding of corrosion damaged structures, but the cost of oxidation prevention bypainting and repainting must also be considered.
Many applications of COR-TEN® show that better economy can be achieved in either the
painted or unpainted form where high strength similar to conventional S355 steels can be used
to construct lighter structures utilising well established design practice, but with the advantage
of improved weathering properties.
Paint lasts longer onCOR-TEN®The surface of weathering steel can be painted usingthe same methods applied in painting ordinary steels.As a result of the special alloying of the steel, a coat ofpaint can last twice as long as a coating on ordinarysteel. If weathering steel is continuously exposed towater, it is usually always recommended to be painted.An advantage of using weathering steel in wetconditions is that it, in case of local effects on paintcoating, corrosion on the spot progresses more slowlythan common steel.
Typical applicationsSteel framed buildings, bridges, tanks, hoppers, chutes,containers, cable trays, exhaust systems, rail & roadvehicles, chimneys, ducting, transmission towers and awide range of structural applications including buildingfacades and even sculptures.
COR-TEN® B S355J0W and S355J2WCOR-TEN® A S355J0WP
Steel Grades
MaterialProperties
COR-TEN® EN 10025-5:2004
COR-TEN® B 0.19COR-TEN® A 0.12
C
0.30 - 0.650.25 - 0.75
Si
0.80 - 1.250.20 - 0.50
MnMaximum Maximum Maximum
Content % (ladle analysis)
Chemical Composition
0.035 max.0.07 - 0.15
P
0.0300.030
S
0.020 - 0.060.015 - 0.06
Al
0.02 - 0.10-
V
0.25 - 0.400.25 - 0.55
Cu
0.40 - 0.650.50 - 1.25
Cr
0.400.65
Ni
COR-TEN® BCOR-TEN® A
Smallest allowable internal bending radius mm
Thickness mm
Formability values apply to all forming directions
-6
-8
-10
-12
2121
2424
3030
3636
4242
48-
54-
60-
COR-TEN® A
Thickness mm
Carbon Equivalent CEV
CEV= C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15
0.8 - 10.0
CEV typical
0.35
Product
Strip products
Normalising 860 - 940(target 910
Stressrelieving
550 - 600(target 580)
Temperature°C
1 minute / mm thickness, minimum 15 minutesFree cooling in air atmosphere outside the oven.
2 minutes / mm thickness, minimum 30 minutesSlow cooling in the furnace
Treatment TimeManner of cooling
Heat Treatment
The yield strength is guaranteed as ReL for COR-TEN ® steels and as R for COR-TEN® steels and as ReH for weathering steel gradesaccording to EN 10025-5:2004. A Charpy V impact test is carried out on standard steels equivalent to COR-TEN® B.
Steel grades and their approximatecorrespondence for weatherresistance.
COR-TEN® A 6.0 - 12.0 0.39 Plate productsCOR-TEN® B 6.0 - 20.0 0.48 Plate productsCOR-TEN® B (20.0) - 40.0 0.50 Plate products Rural
Corrosion allowance to be added forone side of the nominal thicknessfor each 10-year period of workinglife. First 10 year period mm
Type ofatmosphere
Example of corrosion allowance foruntreated COR-TEN® steel
0.10
Each following10 year periodmm
0.05Urban1) 0.20 0.05Industrial2) 0.20 0.10
(2) -3 (3) -4 (4) -5 (5) -6 (6) -7 (7) -8 (8) -10 (10) -12 (12) -14 (14) -16 (16) -18 (18) -20
COR-TEN® BCOR-TEN® A
COR-TEN® Thickness mmStrip products
Plate products
Yield strengthRel N/mm2
Minimum
Tensile strengthRm N/mm2
Minimum
ElongationAso %Minimum
Mechanical properties and Thickness Range
-0.8 - 10.0
6.0 - 40.06.0 - 12.0
345345(HR/RMP) 310(CR)
485485(HR/RMP) 450(CR)
1920(HR/RMP) 22(CR)
S355J0WS355J2W
S355J0WP
EN10025-5:2004
Yield strength ReH N/mm2
Minimum Thickness mm
-
355
Tensile strength RmN/mm2
Minimum Thickness mm
-
510 - 680
Elongation R80 %Minimum Thickness mm
14 15
14 15
A5 % MinimumThickness mm
20
20
2 - 16 2 - (3) 2 (2) - 2.5 3 - 40
355
355
470 - 630
470 - 630
16
16
(16) - 40 3 - 40 (2.5) - (3)
1)With the chief impurity in the air being sulphur dioxide, SO2.2)In addition to SO2. the air also contains chloride. Also for locations inthe immediate vicinity of salt water.
ASD Glen Metals is part of the largest independent steel stockholding group in theUnited Kingdom and is the leading UK Stockholder of COR-TEN® products.We hold themost comprehensive range of both standard and non-standard sizes of COR-TEN®sheet and plate in the UK. Furthermore, the company has extensive coil stocks fromwhich non-standard lengths can be cut.
With over 25 years experience of supplying COR-TEN® products to UK industry, we have
successfully demonstrated our strong commitment to customer satisfaction in terms of
quality and reliability of service.
Our own extensive processing capabilities, backed by group resources, enable us to meet all your
needs in COR-TEN®
Thicknessesmm
CR
Stock Range
0.80 - 1.60
HR
1.50 - 10.0
RMP
10.0 - 40.0
Solutions in Steelwww.glenmetals.comwww.glenmetals.com