GIADA N70E-DRThank you for choosing the N70E-DR ITX NAS main board. The N70E-DR is based on Intel 1037U CPU & Intel HM77 chipsets, and 1*SO-DIMM, DDR3 (Max to 8G), delivers a high performance and professional ITX solution.

WARNING:This motherboard contains static-sensitive components and should be handled with care. Failure to employ adequate anti-static measures can cause partial or complete device failure, performance degradation, or reduced operating life. The battery must be replaced with the correct type of lithium cell battery; otherwise there is a risk of damage to the motherboard. To avoid electrostatic discharge (ESD) damage upon handling this product, it is strongly recommended that you wear a grounded wrist strap or other static dissipating device.

CPU, Memory, Modules installationBIOS SettingDriver installationPlease read in Drivers CD’s manual.

Back Panel Interface:

USB2.0

KB_MS USB3.0 HDMI VGA RJ45-1 RJ45-2 Audio JACK

www.giadatech.com

Connectors and Jumpers:

PCB EDGE

GN

DP

RE

S#

SE

N_

1S

EN

_2

MIC

_L M

IC_

RO

UT

_R

SE

N_

JDO

UT

_L

9 10

1 2

1

2

19

20

1

1

12

BA

BGBF

6160

1

1

1

1

2

91

2

91

2

99

+

1 7

1 71 7

1 7

1 7

1 7

13

B8

2B

81

B2

B1

A8

2A

81

A2

A1

12

V5

V

1

12

1920 12

10

19

1

1110

PCB EDGE

191

1. JPF2. JL1

3. CLR_CMOS

4. USB Port

5. PCIE Slot

6. F_USB2.0

7. F_USB3.0

8. TPM

9. SATA

10. ATX_1x4

11. J6

12. F_PANEL113. JD1

14. JOH15. JPI2C

24. m-SATA 23. COM2

22. JP3.421. ATX2(4Pin)

20. SYS_FAN, CPU_FAN

19. JPUSB1

18. JWD1

17. Memory Socket

16. ATX1(24Pin)

www.giadatech.com

1 2

Port and Connectors:

1. JPFJumper JPF allows you to enable (force on) or disable the Power Force On function. Ifenabled, the power will always stay on automatically. If this function is disabled (the normal setting), the user needs to press the power button to power on the system.

Pin#1-2 Disable2-3 Enable

2. JL1A Chassis Intrusion header is located at JL1 on the motherboard. Attach the appropriate cable from the chassis to inform you of a chassis intrusion when the chassis is opened.

Pin#1 Intrusion Input 2 GND

3. CLR_CMOS Jumper CLR_CMOS is used to clear CMOS

4. USB protIntelnal USB2.0 port.

5. PCIE SlotPCI-E x4 Gen2(in x16 physical)

6. F_USB2.0Front Panel USB 2.0 header

Pin# Pin#1 5V 2 5V3 USB DO- 4 USB D1-5 USB DO+ 6 USB D1+7 GND 8 GND9 N/A 10 NC

321

JPF

21JL1

21CLR_CMOS

12

10

F_USB2.0

7. F_USB3.0Front Panel USB 3.0 header

Pin# Pin#1 5V 2 F-USB3.0 RXDN23 F-USB3.0 RXDP2 4 GND5 F-USB3.0 RXDN2 6 F-USB3.0 TXDP27 GND 8 F-USB2.0 0_N29 F-USB2.0 0_P2 10 F_OCP11 F-USB2.0 0_P1 12 F-USB2.0 0_N113 GND 14 F-USB3.0 TXDP115 F-USB3.0 TXDN1 16 GND17 F-USB3.0 TXDP1 18 F-USB3.0 TXDN119 5V 20 NC

8. TPM HeaderThis header is used to connect a Trusted Platform Module (TPM), available from a third-party vendor. A TPM is a secu¬rity device that allows encryption and authentication of hard drives. It enables the motherboard to deny access if the TPM associated with the hard drive is not installed

Pin# Pin#1 CLK 2 GND3 FRAME 45 RESET 6 5V7 AD3 8 AD29 3V3 10 AD111 AD0 12 GND13 RSV0 14 RSV115 3V3_SB 16 SERIRQ17 GND 18 CLKRUN19 LPCPD 20 RSV2

9. SATASATA 0,1are SATA3.0 headers, SATA 2,3,4,5 are SATA2.0 headers.

Pin#1 GND2 TXP3 TXN4 GND

Pin#5 RXN6 RXP7 GND

19

1

1110

F_USB3.0

19

2 1

20

TPM

www.giadatech.com www.giadatech.com

3 4

www.giadatech.com www.giadatech.com

5 6

10. ATX_1x4PPower Connector for Add-on devices (Note: Do NOT plug the power supply into this socket)

Pin# Pin#1 12V 3 GND2 GNG 4 5V

11. J6Jumper J6 allows you to enable or disable the m-SATA.

Pin# m-SATA SATA31-2

Enable Disable2-3Disable Enable

12. F_PANELFront panel header.

Pin# Pin#1 Powerbotton 11 VCC2 GND 12 NIC1 LED-3 Resetbotton 13 3.3V4 GND 14 HD LED-5 VCC 15 3.3V6 Power Fail LED- 16 Power LED-7 VCC 17 X8 OH/FAN Fail LED- 18 X9 VCC 19 NMI10 NIC2 LED- 20 GND

13. JD1External Buzzer/Speaker/Power LED, Pins 1-3 (Power LED), Pins 4-7 (External Speaker)

Pin# Pin#1 Power LED+ 4 External Speaker+2 NC 5 NC3 Power LED- 6 NC

7 External Speaker-

14. JOHThe JOH header is used to connect an LED to provide warnings of chassis overheat. This LED will also blink to indicate a fan

Pin#1 VCC2

15. JPI2C Power System Management Bus (I2C) Connector monitors the status of the power supply, fan and system temperature. See the

Pin#1 Clock2 Data3 Power Fail-4 GND5 3V3

ATX2

12V

5V

41

23

321

J6

19

2

1

20 F_PANEL1

7 123456

JD1

12

JOH

12345

JPI2C

Power Fail LED-

www.giadatech.com www.giadatech.com

7 8

16. ATX1(24PIN)ATX 24-Pin Power Connector

Pin# Pin#1 3.3V 13 3.3V2 3.3V 14 -12V3 GND 15 GND4 5V 16 FS-ON5 GND 17 GND6 5V 18 GND7 GND 19 GND8 PG 20 -5V9 5VSB 21 5V10 12V 22 5V11 12V 23 5V12 3.3V 24 GND

17. Memory socketsupports up to 8GB of unbuffered Non-ECC DDR3 SODIMM

18. JWD1Watch Dog Enable/Disable

Pin#1-2 Enable2-3 Disable

20. CPU_FAN, SYS_FANCPU Fan header and SYSTEM Fan header.

CPU-FAN SYS-FANPin# Pin#

1 GND 1 GND2 +12V 2 +12V3 Tachometer 3 Tachometer4 PWM_Control 4 PWM_Control

21. ATX2(4PIN)External Power Connector

Pin# Pin#1 12V 3 GND2 GND 4 5V

22. JP3,4Pin 1 DCD/P5V Select (COM1/COM2)

Pin#1-2 DCD2-3 5V

23 COM2 Serial Port 2 Headers

Pin# Pin#1 DCD 6 DSR2 RXD 7 RTS3 TXD 8 CTS4 DTR 9 RI5 Ground 10 N/A

24. m-SATAAllows you install SSD on it.

1 2 3

JP3.4

13

24

ATX2

1

2

9321

JWD1