GeneTouchMonitor User Guide-2.3

Product specification subject to change without prior notice. Page 1/28

GeneTouch Corp.

Monitor User Guide

Version 2.3


GeneTouch Corp.

1. Introduction

2. Installing the Monitor

3. Using the Monitor

4. GT-IPC (option)

5. Installation

6. Cleaning the LCD Monitor 7. Disclaimer

8. Trouble Shooting 9. Supplement


GeneTouch Corp.

IMPORTANT SAFETY INSTRUCTIONS

1. Please read this instructions carefully before using the product and keep it for later reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Clean the product with a damp soft cloth. Do not use liquid or aerosol cleaners as it may cause permanent damage to the screen. 4. Caution of use varies from model to model, please observe appropriate operation per model in use. 5. Do not place this product on an unstable cart, stand, or surface which may cause damage or harm to the product or personnel. 6. Slots and openings on the cabinet, in the back cover or in the bottom, are for ventilation; to ensure reliable operation and to prevent from overheating, these openings must not be blocked or covered at all time. The openings should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation space(min. 2 inches/5cm of gap) is provided. 7. This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local service company. 8. This product is equipped with a 3-wire grounding type power plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you do not have proper outlet to insert the plug, contact your electrician to replace your obsolete outlet. Do not break the ground pin and defeat the purpose of the grounding. 9. Do not allow anything to rest, or persons to walk, on the power cord.. 10. If an extension cord is used with this product, make sure that the total ampere rating plugged into the extension cord does not exceed the maximum ampere rating of the extension cord. 11. Never thrust object/tool of any kind through cabinet slots of this product, as they may touch dangerous voltage point or short out parts that could result in risk of fire or electric shock. Never spill liquid of any kind on the product(except IP-rated models). 12. Do not attempt to service this product yourself, always refer to qualified or authorized personnel for servicing this product. 13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: � When the power cord or plug is damaged or frayed or broken. � In case that liquid has been spilled into the product(excepting IP-rate models). In case the product does not operate normally when the operating instructions are followed, adjust only those controls that are delineated by the operating instructions.


GeneTouch Corp.

1. Introduction 1-1 About the Product This monitor is made of TFT LCD panel and microprocessor -controlled main board. It is designed to meet the demanding or rigid performance requirements of education/schools, public premises, corporate, and industrial applications. 1-2 Notice 1. Do not apply any sharp object on the original LCD panel surface, if model is without protective glass. 2. Do not use corrosive or abrasive detergents, waxes or solvents for cleaning. Use only a dry or

damp with clean water, soft cloth when cleaning. 3. Use qualified and safety-approved AC power cord only. 1-3 Check List When opening the carton, please make sure that all the items listed below are present: 1. VGA cable (male-to-male) ×1 2. Power cord ×1 3. USB cable × 1(for touch monitor models only) 4. User guide ×1 (e-file in CD and specific driver) 5. Remote control x 1, battery included If any items are missing or damaged, please contact your dealer immediately. Following items are optional at specific ordering: 6. DVI cable(optional) 7. VGA cable (male-to-male) (optional) for VGA out application 8. HDMI cable(optional) 9. RS232 to RS485 adapter(optional) 10. HDMI-to-DVI adapter (optional)


GeneTouch Corp.

2. Installing the Monitor The procedures for setting up your Monitor kit is as followed: 2-1 Power & Signal Connections

2-1-1. Power cord connection:

Connect the power cord to the AC outlet. 2-1-2. Power on:

Switch on the main power of your monitor (switch is located next to the AC outlet) 2-1-3. VGA Signal cable connection:

Plug one end of the 15-pin signal cable to the video signal connector at the rear of the PC system (or engine box) and the other end to the monitor. Secure the connectors with the screws on the cable connector at both ends.

2-2 Optional Connections:

This Monitor is designed to work with second signal source. Please enter OSD menu to switch between these signal sources and other adjustments 2-2-1 DVI connection(optional cable):

Plug one end of the DVI signal cable to signal source(PC, or, IPC, or, media player of any kind with proper DVI out port), and the other end to the DVI connector on the monitor. Tighten the connector screws on both ends of the cable to secure good signal connection. 2-2-2 VGA output connection (Optional male to male VGA cable):

Plug one end of the VGA signal cable to signal source and the other end to another VGA in connector to daisy-chain, of cascading, signal to the other monitor. Tighten the connector screws on both ends of the cable to secure good signal connection. 2-2-3 USB cable connection (for touch monitor model s):

Plug one end of the USB cable to the USB connector at the rear of the(PC, or, IPC, or, media player), and the other end to the USB connector on monitor.


GeneTouch Corp.

3. Using the Monitor 3-1 Get to know the monitor The Monitor connectors are located on the rear side. They are shown in the physical monitor as

figure below and described in the following paragraphs. Please note that connectors may vary in some derivative models, please refer to individual leaflet for special notation.

3-2 Connector ports The Figure below depicts the signal connectors on the main board.


GeneTouch Corp.

3-3 Remote Control The outlook of remote control is shown in the Figure, hereafter,

Size: 110 x 44 x 22mm Operation distance: > 10 meter Working angle: not more then +/- 40 degree

3-4 Understanding the OSD Menu(with Remote control)

a. Power on/off Press the power button to turn on/off the monitor. b. Auto Press this button to auto-adjust and optimize picture screen of the monitor. c. Brightness button Press this button to quick-access brightness control only to turn brightness up or down.

d. Menu


GeneTouch Corp.

Press the Menu button to go into OSD menu. e. Exit function Press Exit button to exit setting, or, exit OSD menu. Alternatively, press “Menu” button will exit OSD Menu instantly at any time. f. Select function for adjustment Press the (▲/▼) button to scroll up and down the intended function items for adjustment, and then press the Enter button to activate that function item. g. Adjust the function item setting Press the Enter button to enter the sub-menu and press the (▲/▼) button to adjust the value of setting. Once you adjust the value of setting, the value will be memorized instantly. h. DVI Press this button to enter DVI signal source. i. VGA Press this button to enter VGA signal source. Source default is at VGA source. j. Aux Reserved for alternative use.(HDMI 1 / HDMI 2 /YPBPR) k. Mute Press this button to mute or un-mute. l. Infol. Infol. Infol. Info Press to show timing and resolution


GeneTouch Corp.

3-4 Content of OSD Menu

Press "▲" to increase or "▼" to select.

Press “↵“ to enter

Color




GeneTouch Corp.

� CONTRAST: Use to adjust the screen’s contrast

� BRIGHTNESS: Use to adjust the screen’s brightness

� Color Adjust

Press “↵“ to enter sub menu

Adjust: Use to set the RGB gain


GeneTouch Corp.

� Color Temp

9300K: Use to set value of monitor for the CIE coordinate 9300 color temp. 6500K: Use to set value of monitor for the CIE coordinate 6500 color temp. 5800K: Use to set value of monitor for the CIE coordinate 5800 color temp.

sRGB: Standard RGB color space created by Microsoft and HP USER: Color temperature created by user.

Image Setting



Clock


GeneTouch Corp.

Press "▲" to increase or "▼" to decrease. Use to adjust timing of signal to best adapt to LCD panel pixel rate

Phase

Press "▲" to increase or "▼" to decrease. Use to fine-tune video noise to achieve clearer picture Sharpness

Press "▲" or "▼" to select Use to fine-tune the legibility of fine graphic/word .

Position Use to set the Image’s position.


GeneTouch Corp.

Press “enter” to select and "▲" to increase or "▼" to decrease. � H-POSITION: Use to adjust the image to the left or right on the screen � V-POSITION: Use to adjust the image to the up or down on the screen

OSD Menu

Use to set the OSD at your preference.

Press “enter” and "▲" or "▼" to select, and to move the OSD position in horizontal, or, vertical direction. OSD H.Pos. OSD V.Pos

OSD Timer Use to set the time of OSD on screen. Value 0 the OSD will always display.


GeneTouch Corp.

Language Use to select different languages (max. 7 languages) for OSD Menu.

Misc.

� Light Sensor ON/ OFF: to switch ambient light sensor on or off

� Signal source: Choose input source of VGA / DVI / HDMI 1 / HDMI 2 /YPbpr

� Auto Color: to Auto adjust Color (under source D-Sub only)


GeneTouch Corp.

� Reset: to go back to previous setting.

� FW VERSION: to check F/W version of Monitor


GeneTouch Corp.

3-5 Understanding of Keypad (option) The outlook of keypad is shown in the Figure, hereafter,

a. Power on/off Press the power button to turn on/off the monitor. b. Menu Press the Menu button to go into OSD menu. c. Exit function Press Exit button to exit setting, or, exit OSD menu. Alternatively, press “Menu” button will exit OSD Menu instantly at any time. d. Volume Up/ Down and Select function for adjustme nt Press Vol+/ Vol- for hotkey of volume up/ down or Press the (▲/▼) button to scroll up and down the intended function items for adjustment, and then press the Enter button to activate that function item.


GeneTouch Corp.

e. Source Press this button to change source D-SUB/ DVI/ Aux source. f. Mute Press this button to mute or un-mute.

4. GT-IPC (option)

CPUCPUCPUCPU AMD Socket AM2 Althon™64, Althon™64 X2, ADD4200IAA5DOE MotherboardMotherboardMotherboardMotherboard

System Chipset AMD RS780E + SB710 BIOS AMI BIOS Memory Two 240-pin 667/800 DDR2 dual-channel SDRAM DIMMs supported (system max. 4GB) Ethernet Dual Realtek PCIe RTL8111CP GbE Chipsets I/O Interface 8 x USB2.0 4 x SATA 3Gb/s with RAID 0, 1, 10 1 x RS-232 2 x PS2 for KB/MS


GeneTouch Corp.

1 x TPM Graphic ATI Radeon™ HD3200 Graphic core for DX10 support Graphic Memory share system memory up to 512MB (system 2GB) Expansion 1 x PCIe x16 Display Output VGA integrated in the AMD RS780E (Max. resolution 1920x1080@32bpp) Support HDMI resolution up to 1080p integrated in the AMD RS780E Dual link DVI-D integrated in the AMD RS780E (Resolution 1920x1080) Digital I/O 8-bit digital I/O, 4-bit input/ 4-bit output Super IO Fintek F71859 Audio Realtek ALC888 HD Codec

Power Supply ATX power supply Temperature Operation: 0°C ~ 60°C (32°F ~ 140°F) Humidity Operation: 5% ~95% non-condensing

CPUCPUCPUCPU Supports 2nd Generation Intel® CoreTM i7/i5/i3 in LGA 1155 Package

MotherboardMotherboardMotherboardMotherboard


GeneTouch Corp.

BIOS 64Mb AMI BIOS Chipset Intel® H67

Memory Dual Channel DDR3 Memory Technology, 2 x DDR3 DIMM slots Supports DDR3 1333/1066 non-ECC, un-buffered Memory Max. capacity of system memory: 16GB

*Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 32-bit OS. For Windows® 64-bit OS with 64-bit CPU, there is no such limitation.

Ethernet Dual Realtek RTL8111E I/O Interface 4 x USB2.0, 2 x USB3.0, 4 x SATA 6Gb/s ,1 x RS-232 1xPS/2, 1 x Optical SPDIF, 1 x HDMI 1 x DVI, 1 x VGA, 1 x RJ-45 LAN Port, HD Audio Jack Graphic Intel® HD Graphics 2000/3000

Expansion 1 x PCIe 2.0x16 solt Audio 7.1 CH HD Audio with Content Protection(Realtek ALC892 Audio Codec) Premium Blu-ray audio support


GeneTouch Corp.

Power Supply ATX power supply Humidity Operation: 5% ~95% non-condensing

CPUCPUCPUCPU Intel® Dual-Core Atom™ Processor D525(1.8GHz)

MotherboardMotherboardMotherboardMotherboard

BIOS 4Mb AMI BIOS Chipset Intel® NM10 Express

Memory 2 x DDR3 DIMM slots Supports DDR3 800 non-ECC, un-buffered Memory Max. capacity of system memory: 8GB

*Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 32-bit OS. For Windows® 64-bit OS with 64-bit CPU, there is no such limitation.

Ethernet Atheros AR1851 I/O Interface


GeneTouch Corp.

4 x USB2.0, 1 x Parallel Port, 1 x RS232, 2xPS/2, 1 x VGA, 1 x RJ-45 LAN Port, HD Audio Jack Graphic Intel® Graphics Media Accelerator 3150

Expansion 1 x PCIe 2.0x16 slot Audio 5.1 CH HD Audio(Realtek ALC662 Audio Codec)

Power Supply ATX power supply Humidity Operation: 5% ~95% non-condensing

Hard DriveHard DriveHard DriveHard Drive HD 2.5” HD ST9250315AS 250GB/ 320GB/ 500GB (option) DDDDrrrram DDRII 2Gx2 (240pin)am DDRII 2Gx2 (240pin)am DDRII 2Gx2 (240pin)am DDRII 2Gx2 (240pin) BlueBlueBlueBlue----Ray (option)Ray (option)Ray (option)Ray (option) Card Reader Model: CRCard Reader Model: CRCard Reader Model: CRCard Reader Model: CR----USB2.0USB2.0USB2.0USB2.0----35B35B35B35B----UUUU (option) (option) (option) (option) Wireless 802.11NWireless 802.11NWireless 802.11NWireless 802.11N (option) (option) (option) (option)


GeneTouch Corp.

5. Installation 5-1 Stand This stand is standard for 32”, and optional for al l other sizes. 1. Find the appropriate stand, take out the kit, use the bolts attached and install the back plate

first.

2. Assemble the stand and supporting pole, and align the sliding groove, and slide in the stand , tighten the securing bolts.

3. Stand the monitor upright, and place it to desirous position.


GeneTouch Corp.

5-2Wall Mount Kits Subject to different gross weight per model, please use appropriate weight load wall mount kit only. 32”

42”~55”


GeneTouch Corp.

60”~70”

82”


GeneTouch Corp.

6. Cleaning the LCD Monitor 1. Make sure the monitor is turned off. 2. Never spray or pour any liquid directly onto the screen or case (depends on different model). 3. Do not use chemical solvents, alcohol, or any other based to clean the unit or panel. It may cause permanent damage on the unit or panel. 4. Use a clean, soft, lint-free cloth, or apply a small amount of non-ammonia, non-alcohol based glass cleanser to achieve maximum cleaning.

7. Disclaimer The manufacturer assumes no responsibility, and will not be liable of any damage resulting from non-conforming safety actions or operation, or, cleaning on this product.

8. Trouble Shooting Before calling for service, please try following easy and simple steps to verify: Symptom Check Point 1. No picture � Check if the signal cable is firmly seated in the socket.

� Check if the Power is ON at the computer � Check if the brightness control is at the appropriate position, not at the minimum. � State the monitor is powered on and the LED of power is GREEN, plug out the VGA cable and plug in again.

2. The screen is not synchronized

� Check the LED light if it indicates in red, the device is in power off status. Use the remote and press “Power” to turn the power on. � Use the “Auto” key on remote control to automatically adjust the monitor timing scan. � Check if the signal cable is firmly seated in the socket. � Make sure the signal timings of the computer system are within the specification of the monitor. � If your computer was working with a CRT monitor, you should check the current signal timing and turn off your computer before you connect the VGA Cable to this monitor.


GeneTouch Corp.

3. The picture is not centered � Adjust the H-position, and V-position, or Perform the Auto adjustment.

5. The screen is flickering

� Press the “Auto” - adjustment control by remote control or OSD to adjust. Re-locate nearby devices, such as motor, or transformer, which generate magnetic field, away from the monitor. Check if the specific voltage is applied. � Check if the signal timing of signal source (PC, IPC, or media playerngine box) is within the specification of monitor. If you are unable to correct the fault by following this chart, stop using your monitor and contact your distributor or dealer for further assistance.


GeneTouch Corp.

9. Supplement This Monitor is designed to meet following VESA standard resolution and timing per two different types of LCD panel’s native resolution. For 1366 x 768 panel, i.e. 26"/32" Analog timing support Digital timing support No. Resolution fV(Hz) fH(KHz) No. Resolution fV(Hz) fH(KHz) 1 640x350 85 37.9 1 640x400 85 37.9 2 640x400 85 37.9 2 640x480 60 31.5 3 640x480 60 31.5 3 640x480 72 37.9 4 640x480 72 37.9 4 640x480 75 37.5 5 640x480 75 37.5 5 640x480 85 43.3 6 640x480 85 43.3 6 720x400 85 37.9 7 720x400 85 37.9 7 800x600 56 35.1 8 800x600 56 35.1 8 800x600 60 37.9 9 800x600 60 37.9 9 800x600 72 48.1 10 800x600 72 48.1 10 800x600 75 46.9 11 800x600 75 46.9 11 800x600 85 53.7 12 800x600 85 53.7 12 1024x768 60 48.4 13 1024x768 60 48.4 13 1024x768 70 56.5 14 1024x768 70 56.5 14 1024x768 75 60 15 1024x768 75 60 15 1024x768 85 68.7 16 1024x768 85 68.7 16 1152x864 75 67.5 17 1152x864 75 67.5 17 1280x720 60 44.8 18 1280x720 60 44.8 18 1280x768 60 47.4 19 1280x768 60 47.4 19 1280x768 75 60.3 20 1280x768 75 60.3 20 1280x768 85 68.6 21 1280x768 85 68.6 21 1280x960 60 60 22 1280x960 60 60 22 1280x960 85 85.9 23 1280x960 85 85.9 23 1280x1024 60 64 24 1280x1024 60 64 24 1280x1024 75 80 25 1280x1024 75 80 25 1280x1024 85 91.1 26 1280x1024 85 91.1 26 1366x768 60 47.7 27 1366x768 60 47.7


GeneTouch Corp.

For 1920 x 1080 panel, i.e. 42”~82” Analog timing support Digital timing support No. Resolution fV(Hz) fH(KHz) No. Resolution fV(Hz) fH(KHz) 1 640x350 85 37.9 1 640x400 85 37.9 2 640x400 85 37.9 2 640x480 60 31.5 3 640x480 60 31.5 3 640x480 72 37.9 4 640x480 72 37.9 4 640x480 75 37.5 5 640x480 75 37.5 5 640x480 85 43.3 6 640x480 85 43.3 6 720x400 85 37.9 7 720x400 85 37.9 7 800x600 56 35.1 8 800x600 56 35.1 8 800x600 60 37.9 9 800x600 60 37.9 9 800x600 72 48.1

10 800x600 72 48.1 10 800x600 75 46.9 11 800x600 75 46.9 11 800x600 85 53.7 12 800x600 85 53.7 12 1024x768 60 48.4 13 1024x768 60 48.4 13 1024x768 70 56.5 14 1024x768 70 56.5 14 1024x768 75 60 15 1024x768 75 60 15 1024x768 85 68.7 16 1024x768 85 68.7 16 1152x864 75 67.5 17 1280x768 60 47.4 17 1280x768 60 47.4 18 1280x768 75 60.3 18 1280x768 75 60.3 19 1280x768 85 68.6 19 1280x768 85 68.6 20 1280x960 60 60 20 1280x960 60 60 21 1280x960 85 85.9 21 1280x960 85 85.9 22 1280x1024 60 64 22 1280x1024 60 64 23 1280x1024 75 80 23 1280x1024 75 80 24 1280x1024 85 91.1 24 1280x1024 85 91.1 25 1366x768 60 47.7 25 1366x768 60 47.7 26 1440x900 60 55.5 26 1440x900 60 55.5 27 1440x900 75 70.6 27 1440x900 75 70.6 28 1600x1200 60 75 28 1600x1200 60 75 29 1600x1200 65 81.3 29 1680x1050 60 64.7 30 1600x1200 70 87.5 30 1920x1080 60 67.2 31 1600x1200 75 93.8 32 1680x1050 60 64.7 33 1680x1050 75 82.3 34 1920x1080 60 67.2

Documents

GeneTouchMonitor User Guide-2.3