Upload
-
View
260
Download
3
Embed Size (px)
Citation preview
7/27/2019 FS 508 Installation Manual
1/8
E-14349-7702-01
INSTALLATION MANUAL
FS-508 Finisher
Applied Machine: /DEVELOP GmbH
I. Outline of Installation Procedures for ineo 250/ineo 350 System
When installing the machine and associated options as a system, follow the order shown on the upper.
Note:
For the detailed installation procedures for each option, follow the instructions given in the corresponding
Installation Manual and perform the procedures correctly.
PC-102 PC-402PC-202
DF-605
JS-502FS-508
SD-502
OT-601
Machine
PU-501
HD-504
EM-303/
EM-304/
EM-305
FK-503SU-501MT-501
ML-502
EK-502
OC-502
4349U010AA
7/27/2019 FS 508 Installation Manual
2/8
E-2
II.Accessory parts
No. Name Figure Qty
1. Finisher Unit
1
2. Tray Unit
1
3. Front Cover
1
4. SecondaryCover
1
5. Exit Tray
(Upper)1
6. Exit Tray
(Lower)1
7. Retaining Plate1
8. E-ring1
9. Screw A
(4 8 mm) 6
10. Screw B
(4 8 mm) 1
11. Screw C
(3 8 mm) 3
12. Screw D
(3 8 mm) 6
13. Label1
14. Installation
Manual
1 set
4349U011AA
4349U012AA
4349U013AA
4349U014AA
4349U015AA
4349U048AA
4349U016AA
9723
9646
9735
9735
9739
4980IXC019DA
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting your head in the wrapper involves
danger of suffocation.
7/27/2019 FS 508 Installation Manual
3/8
E-3
III. Installation procedures
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Open the packaging box and remove the Finisher
and other accessories.
Note:
Be sure to hold onto the portions shown in the
illustration when taking the Finisher Unit out of the
box.
NEVER hold onto part A.
3. Remove pieces of protective tape.
4. Remove the fixing bracket of the Finisher Unit
(ten screws).
Note:
Screws 1 and 2 are used in step 6.
4349U017AA
A
4349IXC001DB
4349U050AA
4349IXC002DB
4349IXC004DA
Screw 1Screw 2
7/27/2019 FS 508 Installation Manual
4/8
E-4
5. Remove the protective tape from the Staple Unit.
6. Screw screws 1 and 2, which have been
unscrewed from the fixing bracket in step 4, to the
Staple Unit (two screws).
* Screw them into the positions, from which they
have been unscrewed.
7. Remove the fixing bracket of the Tray Unit (six
screws).
8. Open the Front Door.
9. Remove the Exit Cover (three screws).
10.Remove the cover.
11.Remove the tray.
12.Using a cutter or nippers, remove the Exit Rolls.* Gray Exit Rolls (three)
4349IXC003DA
4349U021AB
4349U023AA
4349IXC005DA
4349U046AA
4349U024AA
4349U025AA
7/27/2019 FS 508 Installation Manual
5/8
E-5
13.Holding the positions indicated by the arrows in
the illustration, place the Finisher Unit onto the
rail of the machine.
14.Slide the Finisher Unit all the way back into the
machine.
15.Check to see if clearance A between the rail ofthe machine and the Finisher Unit measures 1
0.5 mm.
16.If the clearance measures more than 1 0.5 mm,
slide out the Finisher Unit with the portion indi-
cated in the illustration pushed with a screwdriver
or similar tool.
17.Loosen the adjusting screw and move the Fin-
isher Unit to the right or left as necessary (one
screw).
18.After the adjustment have been made, tighten the
adjusting screw.
4349U026AC
Rail
4349U027AA
4349U022AA
Rail Finisher
Unit
A
4349U028AC
4349U029AC
7/27/2019 FS 508 Installation Manual
6/8
E-6
19.Make sure that the Paddle of the Finisher Unit is
not advanced.
20.If the Paddle is advanced, push the solenoid
shown and turn the Misfeed Clearing Dial to bring
the Paddle into its retracted position.
21.Mount the Tray Unit onto the Finisher Unit.
Note:
Use utmost care to prevent the Tray Unit from con-
tacting the solenoid and motor of the Finisher Unit.
22.Using Screws, secure the Tray Unit by tightening
the screws in the order shown in the illustration
(six screw As furnished with the Finisher).
23.Using Screw, secure the ground wire (one screw
B furnished with the Finisher).
Note:
Make sure that the ground wire runs in the direc-
tion shown in the illustration when secured.
24.Connect the three connectors.
25.Using Screw, secure the ground wire (one screw
C furnished with the Finisher).
4349U031AA
4349U030AA
Paddle
4349U057AA
Motor Solenoid
4349IXC006DA
5
1
3
6
2
4
4349U034AB
4349U051AB
7/27/2019 FS 508 Installation Manual
7/8
E-7
26.Using Screws, secure the Secondary Cover in
position (two screw Cs furnished with the Fin-
isher).
Note:
Make sure that there is a uniform clearance
between the Misfeed Clearing Dial and Secondary
Cover.
27.Using Screw, secure the Secondary Cover (one
screw D furnished with the Finisher).
28.Install the Front Cover to the machine.
29.Close the Front Cover.
30.Snap the E-ring into position.
31.Remove the cover from the Exit Cover that have
been removed in step 9 (two screws).
32.Remove the label from the Front Cover.
33.Using the screws removed in step 31, secure the
cover that have been removed in step 31 to the
Front Cover (two screws).
4349U036AC
4349U037AA
4349U055AA
4349U052AA
4349U039AB
4349U040AD
Label
7/27/2019 FS 508 Installation Manual
8/8
E-8
34.Using Screw, secure the band and the Retaining
Plate to the Secondary Cover (one screw D fur-
nished with the Finisher).
35.Fit the label back to the Front Cover.
36.Close the Front Cover.
37.Install the upper and lower Exit Trays (four screw
Ds furnished with the Finisher).
38.Affix the Label furnished with the Finisher.
4349U041AB
4349U043AB
4349U045AB
4349U044AB