Upload
trankhanh
View
225
Download
5
Embed Size (px)
Citation preview
Free Machining Stainless Steel
Wire
Mac
hina
bilit
y
Corrosion resistance
Ugitech 420F Ugitech 430F
Ugima 303
Ugima Vitinox18x
Ugitech 420 Ugima 304LCu
Ugima 4435
Martensitic gradesFerritic gradesAustenitic grades
AISIstandard
designation
EURONORMEN 10.088/3
UGITECHcommercialdesignation
Chemical compositionSpECIfIC fEATURES
C Si Mn Ni Cr Mo Cu S p
304 Cu 1.4567 UGIMA® 304 L Cu 0.030 1.0 2.08.5
10.017.018.5
0.53.04.0
0.0150.04
0.04The best compromise between corrosion resistance and machinability
Well suited for deep drilling and plastic deformation (knurling - thread rolling)
303 1.4305 UGIMA® 303 0.080 1.01.02.0
8.09.5
17.018.5
0.60 0.750.250.35
0.04 The reference in machinability
Austenitic steel appropriate for all types of free machining
1.4570 UGIMA® Vitinox 18X 0.080 1.01.02.0
8.09.5
17.018.5
0.601.02.5
0.250.35
Excellent machinability
free machining grade 4305 but with the addition of Cu to further improve machinability. Recommended for difficult machining operations.
316L 1.4435 UGIMA® 4435 0.030 1.0 2.012.513.5
17.018.0
2.53.0
0.750.0100.03
0.04Ugima grade designed to meet the needs of the Watchmaking Component Industry (ICH)
Excellent corrosion resistance. ferrite content <1%. Nickel salting out <0.5mg/cm2/week
430 F 1.4105 UGITECH 430 F 0.050 1.00.41.5
0.516.018.0
0.60,250,35
0.04The alliance of magnetic properties with machinability
ferritic grade with improved machinability
416 1.4005 UGITECH 416 0.070.1
1.00.071.2
0.512.013.5
0.30.250.35
0.04Martensitic stainless steel with a high degree of machinability
Recommended for rough drawn parts before treatment and finishing
420 1.4028 UGITECH 420 0.280.35
1.0 1.5 0.512.014.0
0.5 0.03 0.04The option of high mechanical properties in the heat treated condition
A combination of good mechanical properties in the treated state and good corrosion resistance in environments with low aggressivity
420 F 1.4029 UGITECH 420 F 0.260.31
1.00.71.3
0.512.013.0
0.40.150.25
0.04The alliance of mechanical properties with machinability
Recommended for machined parts with high mechanical properties used in an environment with low aggressivity
Free machiningTo meet the demands for precision and productivity of the free
machining industry, our products combine the low-cost benefits of the UGIMA® grades with geometric precision.
UGIMA®
A “must” in machinabilityIn addition to the usual parameters used to improve machinability (sulfur content, cold hardening, etc.), our main grades undergo the UGIMA®. processing mode. This process consists in controlling the inclusionary condition of the product, improving free machiningproductivity by 15 to 50%.
PerformanceOur grades represent the best compromise between:• corrosion resistance• machinability
Drum - pallet with coverØ 800 - H 600 - 250 Kg (Ø 31.5” - h 23.5” - 113 Lbs )
GRADESAnnealed Cold drawn
diatol
Average Tensile diatol
Average Tensilemm inches mpa Ksi mm inches mpa Ksi
UGIMA® 304LCu 1 to 5 .039”to.196” ISO 9 600 87 1 to 9 .039”to.354” ISO 8 700 102
UGIMA® 303 1 to 5 .039”to.196” ISO 9 630 91 1 to 9 .039”to.354” ISO 8 750 109
UGIMA® Vitinox 18X 1 to 5 .039”to.196” ISO 9 630 91 1 to 9 .039”to.354” ISO 8 750 109
UGIMA® 4435 1 to 5 .039”to.196” ISO 9 650 94 1 to 9 .039”to.354” ISO 8 850 123
UGITECH 430F 2 to 5 .078”to.196” ISO 9 530 77 2 to 9 .078”to.354” ISO 8 600 87
UGITECH 416 2 to 5 .078”to.196” ISO 9 520 75 2 to 9 .078”to.354” ISO 8 600 87
UGITECH 420 2 to 5 .078”to.196” ISO 9 680 98 2 to 9 .078”to.354” ISO 8 830 120
UGITECH 420F 2 to 5 .078”to.196” ISO 9 650 94 2 to 9 .078”to.354” ISO 8 810 118
HP QualityPossibility to produce high precision wires with ISO tolerances 6 and 7, with a “slightly cold hardened” metallurgical quality, in the size range between 1 and 5 mm. (.039” and .196”)
Standard product rangeSurface roughness in the lightly cold work conditiondia 1 < 2,50 Average Ra 0,4 micron CLAdia 2,50 < 5,00 Average Ra 0,8 micron CLA dia ≥ 5,00 Average Ra 1,2 micron CLA
Coils from 30 to 100 Kg (13.5 Lbs to 45 Lbs) on palletInside coil Ø: Ø 1 to 1.50 mm = 350 mm(.039” to .196” = 13.8”)Ø > 1.50 mm = 500 mm(.060” = 19.7”)
Packaging
Reels, 250 or 400Kg(113 Lbs or 181 Lbs)Outside Ø 760 mm (30”boring Ø 40 mm (1.58”)
Wires recommended by Esco S.A.
www.ugitech.com
Bars
UGITECHAvenue Paul Girod73403 UGINE CedexFRANCETel. +33 (0)4 79 89 30 30Fax: +33 (0)4 79 89 34 34
UGITECH ItaliaVia G. Di Vittorio, 34/3620068 PESCHIERA BORROMEO (MI)ITALYTel. +39 02 54 74 34 14Fax: +39 02 54 74 34 30
Wire rod
UGITECHAvenue Paul Girod73403 UGINE CedexFRANCETel. +33 (0)4 79 89 30 30Fax: +33 (0)4 79 89 34 34
Drawn wire
UGITECHBP 3358160 IMPHYFRANCETel. +33 (0)3 86 21 37 98Fax: +33 (0)3 86 21 31 03
UGITECHPetite Rue VolaisBP 11527800 BRIONNEFRANCETel. +33 (0)2 32 47 33 37Fax: +33 (0)2 32 44 96 39
UGITECH3, Chemin de MajornasBP 110901009 BOURG-EN-BRESSEFRANCETel. +33 (0)4 74 50 55 00Fax: +33 (0)4 74 50 55 10
SPRINT METAL Edelstahlziehereien GmbHEckenhagener Strasse 251580 REICHSHOF - PochwerkGERMANYTel. +49 (0)22 61 54 06 23Fax: +49 (0)22 61 54 06 55
SPRINT METALEdelstahlziehereien GmbHGewerbegebiet West39240 BRUMBYGERMANYTel. +49 (0)39 291 46 51 0Fax: +49 (0)39 291 46 51 55
UGITECH production plants
UGITECH a team of 2000 working together for you around the world
GB_Dépliant format A4 photo sur la couverture uniquement 10
Impr
imeu
rs :
Dum
as &
Tito
ulet
- w
ww
.thuria.c
om
- U
gite
ch -
Soc
iété
MOR
ET -
ESC
O SA
- N
on-c
ontra
ctua
l doc
umen
t - 0
2/20
09 -
D74
57