Floor Care - Diversey, Inc. · Floor Stripping (continued) Rinse the floor again before the floor dries. If using an auto scrubber, clean and return to appropriate area. If using

© 2018 Diversey, Inc. All Rights Reserved. 32370-CRD90034 en (18/059)

Always wear personal protective equipment.

Floor CareProcedure Cards

If you have any questions, comments or need to reorder this set of cards, please call 1-800-558-2332

1 3

7

4

8

2

65


Questions: 1-800-558-2332Always wear personal protective equipment.


Assemble your equipment and supplies.

Dust mop the area.

Put on Personal Protective Equipment (PPE).

Prepare your stripping solution water.

Post “Wet Floor” signs and other blockades.

If you are using an autoscrubber, fill with cool water.

Remove freestanding objects. Vacuum and remove walk-off mats.

Apply foaming stripper to baseboards, if necessary. Prepare to control liquid flow.

Floor Stripping

9 11

15

1210

1413



Floor Stripping (continued)

Apply stripping solution.

Check your progress.

Allow the stripping solution to work before scrubbing.

Rinse the floor and pick up the slurry.

Loosen finish on baseboards and corners.

Or use an auto scrubber to rinse and pick up slurry.

Scrub with floor machine or auto scrubber.

16 18 1917

2120



Floor Stripping (continued)

Rinse the floor again before the floor dries.

If using an auto scrubber, clean and return to appropriate area.

If using an auto scrubber, apply water and scrub rinse.

Clean your shoes, clothes, and wash hands.

When the floor is dry, check your work.

Clean your equipment and return it to its appropriate area.

1 3

7

4

8

2

65



Floor Finishing/Sealing


Pour enough sealer or finish for the area.

Note: Skip this step if using a ProSpeedTM/MC or TrailBlazerTM/MC.

Put on appropriate Personal Protective Equipment (PPE).

Dip mop head into the finish or sealer.

Post “Wet Floor” signs and other blockades.

Apply the finish or sealer.

Prepare your mop and bucket.

Normally drying takes 30-45 minutes, depending on the finish or sealer.

9 11 1210



Number each coat. Apply additional finish or sealer coats until desired appearance is achieved.

Discard liner and leftover finish, clean equipment.

Remove “Wet Floor” signs when completely dry.

Floor Finishing/Sealing (continued)

1 3

7

4

8

2

65



Routine Cleaning


Dust mop the floor and remove gum.


Prepare your cleaning solution.

Post “Wet Floor” signs or blockades.

Damp mop light soils.

Remove freestanding objects and trash. Vacuum and remove walk-off mats.

Wet mop heavy soils.

9 1110



Routine Cleaning (continued)

Pick up the cleaning solution with the mop or wet vac.

Rinse equipment. Remove “Wet Floor” signs when floor is dry.

1 3 42

5



Dust Mopping


Dust mop the floor.


Post “Wet Floor” signs or other blockades.


1 3

7

4

8

2

5 6



Deep Scrubbing


Dust mop the entire floor.


Post “Wet Floor” signs or other blockades.

Rotary Machine: When using a rotary machine, liberally apply cleaning solution to the floor.

Note: Rotary floor scrubbing.


Rotary Machine: For heavy buildup, allow the cleaning solution to dwell for additional time.

Prepare your cleaning solution.

(For autoscrubber procedures move ahead two pages)

911109



Deep Scrubbing (continued)

Rotary Machine: Scrub low to medium soiled floors.

Rotary Machine: Scrub heavily soiled floors.

Rotary Machine: Pick up the cleaning solution.

Rotary Machine: Rinse the floor with clean water before it can dry.

1 3 42

65



Autoscrubber

If using an auto scrubber, fill the solution tank with cleaning solution.

Trail mop with clean water and a clean mop head.

Scrub light soils (before burnishing or buffing).

Use an edging tool to clean soils along the wall or on baseboards, if necessary.

When double-scrub heavy soils or damaged finish (before recoating).

Autoscrubber: For heavy soils or damaged finish, a second scrub (before recoating) is necessary.

1 3 42



Rotary and Autoscrubbers

Wipe down baseboards and kick plates.

When the floor is dry, check your work.

Clean and put away equipment.

Remove “Wet Floor” signs when dry.

1 3

7

4

8

2

5 6



Spray Buffing


Mount a red buffing pad on the rotary floor machine.


Post “Wet Floor” signs.

Make three passes.

Dust mop the entire floor.

Change pads as necessary.

Apply spray buff solution in a coarse spray.

9 1110



Clean your equipment and return it to its proper location.

Remove “Wet Floor” signs when floor is dry and dust mopping is complete.

Dust mop the floor after the entire area has been buffed.

Spray Buffing (continued)

1 3

7

4

8

2

5 6



Ultra High Speed (UHS) Burnishing


Mount the appropriate pad on your UHS burnisher.


Post “Wet Floor” signs or blockades.

Change pads as necessary.

Dust mop and damp mop or autoscrub the floor.

Dust mop after burnishing.

Make ONE pass over the work area.

9 10



Ultra High Speed (UHS) Burnishing (continued)

Clean and replace your equipment.

Remove “Wet Floor” signs and blockades after inspecting your work.

Diversey has been, and always will be, a pioneer and facilitator for life. We constantly deliver revolutionary cleaning and hygiene technologies that provide total confidence to our customers across all of our global sectors. Led by Dr. Ilham Kadri, President & CEO, and headquartered in Charlotte, North Carolina, USA, Diversey employs approximately 9,000 people globally, generating net sales of approximately $2.6 billion in 2016.

For more information, visit www.diversey.com or follow us on social media.


Documents

Floor Care - Diversey, Inc. · Floor Stripping (continued) Rinse the floor again before the floor dries. If using an auto scrubber, clean and return to appropriate area. If using